C0805X824K3RACTU [KEMET]
Ceramic Capacitor, Multilayer, Ceramic, 25V, 10% +Tol, 10% -Tol, X7R, 15% TC, 0.82uF, Surface Mount, 0805, CHIP;型号: | C0805X824K3RACTU |
厂家: | KEMET CORPORATION |
描述: | Ceramic Capacitor, Multilayer, Ceramic, 25V, 10% +Tol, 10% -Tol, X7R, 15% TC, 0.82uF, Surface Mount, 0805, CHIP 电容器 |
文件: | 总20页 (文件大小:1391K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP) X7R Dielectric,
6.3 – 250 VDC (Commercial & Automotive Grade)
Overview
KEMET’s Flexible Termination (FT-CAP) multilayer ceramic
capacitor in X7R dielectric incorporates a unique, flexible
termination system that is integrated with KEMET’s standard
termination materials. A conductive silver epoxy is utilized
between the base metal and nickel barrier layers of KEMET’s
standard termination system in order to establish pliability
while maintaining terminal strength, solderability and electrical
performance. This technology was developed in order to
address the primary failure mode of MLCCs– flex cracks, which
are typically the result of excessive tensile and shear stresses
produced during board flexure and thermal cycling. Flexible
environmental and handling conditions, it does provide superior
flex performance over standard termination systems.FT-CAP
complements KEMET’s Open Mode, Floating Electrode (FE-CAP),
Floating Electrode with Flexible Termination (FF-CAP) and KEMET
Power Solutions (KPS) product lines by providing a complete
portfolio of flex mitigation solutions.
Combined with the stability of an X7R dielectric and designed to
accommodate all capacitance requirements, these flex-robust
devices are RoHS-compliant, offer up to 5mm of flex-bend
capability and exhibit a predictable change in capacitance with
termination technology inhibits the transfer of board stress to the respect to time and voltage. Capacitance change with reference to
rigid ceramic body, therefore mitigating flex cracks which can
result in low IR or short circuit failures.
ambient temperature is limited to ±15% from -55°C to +125°C.
In addition to commercial grade, automotive grade devices are
available which meet the demanding Automotive Electronics
Council's AEC–Q200 qualification requirements.
Although this technology does not eliminate the potential
for mechanical damage that may propagate during extreme
Ordering Information
C
1206
X
106
K
4
R
A
C
AUTO
Case Size Specification/ Capacitance Capacitance
Failure Rate/
Design
Packaging/Grade
(C-Spec)2
Ceramic
Voltage
Dielectric
Termination Finish1
(L" x W")
Series
Code (pF)
Tolerance
0603
0805
1206
1210
1808
1812
1825
2220
2225
X = Flexible 2 significant
J = ±5%
K = ±10%
M = ±20%
9 = 6.3 V
8 = 10 V
4 = 16 V
3 = 25 V
5 = 50 V
1 = 100 V
2 = 200 V
A = 250 V
R = X7R A = N/A
C = 100% Matte Sn Blank = Bulk
Termination
digits +
number of
zeros
L = SnPb (5%
minimum)
TU = 7" Reel Unmarked
TM = 7" Reel Marked
AUTO = Automotive
Grade 7" Reel Unmarked
1 Additional termination finish options may be available. Contact KEMET for details.
1,2 SnPb termination finish option is not available on Automotive Grade product.
2 Additional reeling or packaging options may be available. Contact KEMET for details.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012
1
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Dimensions – Millimeters (Inches)
L
W
B
T
S
EIA
Metric
Size
Code
1608
2012
S
L
W
Width
T
B
Mounting
Technique
Size
Code
0603
0805
1206
1210
1808
1812
Separation
Minimum
0.58 (.023)
0.75 (.030)
Length
Thickness
Bandwidth
1.60 (.064) ± 0.17 (.007) 0.80 (.032) ± 0.15 (.006)
2.00 (.079) ± 0.20 (.008) 1.25 (.049) ± 0.20 (.008)
3.30 (.130) ± 0.40 (.016) 1.60 (.063) ± 0.20 (.008)
3.30 (.130) ± 0.40 (.016) 2.50 (.098) ± 0.20 (.008)
4.70 (.185) ± 0.50 (.020) 2.00 (.079) ± 0.20 (.008)
4.50 (.178) ± 0.40 (.016) 3.20 (.126) ± 0.30 (.012)
4.60 (.181) ± 0.40 (.016) 6.40 (.252) ± 0.40 (.016)
5.90 (.232) ± 0.75 (.030) 5.00 (.197) ± 0.40 (.016)
5.90 (.232) ± 0.75 (.030) 6.40 (.248) ± 0.40 (.016)
0.45 (.018) ± 0.15 (.006)
0.50 (0.02) ± 0.25 (.010)
0.60 (.024) ± 0.25 (.010)
0.60 (.024) ± 0.25 (.010)
0.70 (.028) ± 0.35 (.014)
0.70 (.028) ± 0.35 (.014)
0.70 (.028) ± 0.35 (.014)
0.70 (.028) ± 0.35 (.014)
0.70 (.028) ± 0.35 (.014)
Solder Wave
or
Solder Reflow
3216
3225
4520
4532
4564
5650
5664
See Table 2 for
Thickness
N/A
Solder Reflow
Only
1825
2220
2225
Benefits
• -55°C to +125°C operating temperature range
• Superior flex performance (up to 5 mm)
• High capacitance flex mitigation
• Pb-Free and RoHS Compliant
• EIA 0603, 0805, 1206, 1210, 1808, 1812, 1825, 2220, and
2225 case sizes
• Capacitance offerings ranging from 180 pF to 22 μF
• Available capacitance tolerances of ±5%, ±10%, and ±20%
• Non-polar device, minimizing installation concerns
• 100% pure matte tin-plated termination finish allowing for
excellent solderability
• SnPb termination finish option available upon request (5% min)
• Commercial and Automotive (AEC–Q200) grades available
• DC voltage ratings of 6.3 V, 10 V, 16 V, 25 V, 50 V, 100 V,
200 V, and 250 V
Applications
Typical applications include circuits with a direct battery or power source connection, critical and safety relevant circuits without
(integrated) current limitation and any application that is subject to high levels of board flexure or temperature cycling. Examples
include raw power input side filtering (power plane/bus), high current applications (automobile battery line) and circuits that cannot be
fused to open. Markets include consumer, medical, industrial (power supply), automotive, aerospace and telecom.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012
2
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Qualification/Certification
Commercial Grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in
Table 4, Performance & Reliability.
Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test
methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive Components. For additional
information regarding the Automotive Electronics Council and AEC–Q200, please visit their website at www.aecouncil.com.
Environmental Compliance
Pb-Free and RoHS Compliant (excluding SnPb termination finish option).
Electrical Parameters/Characteristics
Item
Parameters/Characteristics
Operating Temperature Range
-55°C to +125°C
±15%
Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC)
Aging Rate (Maximum % Capacitance Loss/Decade Hour)
3.0%
250% of rated voltage
Dielectric Withstanding Voltage (DWV)
Dissipation Factor (DF) Maximum Limit @ 25ºC
Insulation Resistance (IR) Limit @ 25°C
(5 ±1 seconds and charge/discharge not exceeding 50 mA)
5% (6.3 and 10 V), 3.5% (16 and 25 V) and 2.5% (50 to 250 V)
See Insulation Resistance Limit Table
(Rated voltage applied for 120 ±5 seconds @ 25°C)
Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours.
To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.
Capacitance and dissipation factor (DF) measured under the following conditions:
1 kHz ±50 Hz and 1.0 ±0.2 Vrms if capacitance ≤ 10 µF
120 Hz ±10 Hz and 0.5 ±0.1 Vrms if capacitance > 10 µF
Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as
Automatic Level Control (ALC). The ALC feature should be switched to "ON."
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012
3
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Post Environmental Limits
High Temperature Life, Biased Humidity, Moisture Resistance
Rated DC
Voltage
Capacitance
Dissipation Factor
(Maximum %)
Capacitance
Insulation
Resistance
Dielectric
X7R
Value
Shift
> 25
16/25
< 16
3.0
5.0
7.5
All
±20%
10% of Initial Limit
Insulation Resistance Limit Table (X7R Dielectric)
1,000 Megohm
EIA Case Size
500 Megohm
Microfarads or 10 GΩ
Microfarads or 100 GΩ
0201
0402
0603
0805
1206
1210
1808
1812
1825
2220
2225
N/A
< 0.012 µF
< 0.047 µF
< 0.047 µF
< 0.22 µF
< 0.39 µF
ALL
ALL
≥ 0.012 µF
≥ 0.047 µF
≥ 0.047 µF
≥ 0.22 µF
≥ 0.39 µF
N/A
< 2.2 µF
ALL
≥ 2.2 µF
N/A
< 10 µF
ALL
≥ 10 µF
N/A
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012
4
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Table 1A – Capacitance Range/Selection Waterfall (0603 – 1210 Case Sizes)
Series
Voltage Code
Voltage DC
C0603X
C0805X
C1206X
C1210X
Cap
Code
9
8
4
3
5
1
2
9
8
4
3
5
1
2
A
9
8
4
3
5
1
2
A
9
8
4
3
5
1
2
A
Cap
Cap Tolerance
Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions
180 pF
220 pF
270 pF
330 pF
390 pF
470 pF
560 pF
680 pF
820 pF
181
221
271
331
391
471
561
681
821
102
122
152
182
222
272
332
392
472
562
682
822
103
123
153
183
223
273
333
393
473
563
683
823
104
124
154
184
224
274
334
394
474
564
684
824
105
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
1,000 pF
1,200 pF
1,500 pF
1,800 pF
2,200 pF
2,700 pF
3,300 pF
3,900 pF
4,700 pF
5,600 pF
6,800 pF
8,200 pF
10,000 pF
12,000 pF
15,000 pF
18,000 pF
22,000 pF
27,000 pF
33,000 pF
39,000 pF
47,000 pF
56,000 pF
68,000 pF
82,000 pF
0.10 µF
0.12 µF
0.15 µF
0.18 µF
0.22 µF
0.27 µF
0.33 µF
0.39 µF
0.47 µF
0.56 µF
0.68 µF
0.82 µF
1.0 µF
CB CB CB CB CB CB
CB CB CB CB CB CB
CB CB CB CB CB CB
CB CB CB CB CB CB
CB CB CB CB CB CB
CB CB CB CB CB CB
CB CB CB CB CB CB
CB CB CB CB CB CB
CB CB CB CB CB
CB CB CB CB CB
CB CB CB CB CB
CB CB CB CB CB
CB CB CB CB CB
CB CB CB CB CD
CB CB CB CB
DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
DC DC DC DC DC DD DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
DC DC DC DC DC DD DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
DC DC DC DC DC DD DC DC EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
DC DC DC DC DC DD DE
DC DC DC DC DC DD DE
DC DC DC DC DC DD DE
DC DC DC DC DC DE DG
DD DD DD DD DD DE DG
DD DD DD DD DD DE
DD DD DD DD DD DE
DD DD DD DD DD DE
DC DC DC DC DD DG
DC DC DC DC DD DG
DC DC DC DC DG DG
DC DC DC DC DG DG
DD DD DD DD DD
EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
EB EB EB EB EB EB EB EB FB FB FB FB FB FB FB FB
EB EB EB EB EB EC EB EB FB FB FB FB FB FB FB FB
EB EB EB EB EB EC ED ED FB FB FB FB FB FB FC FC
EB EB EB EB EB EB ED ED FB FB FB FB FB FB FC FC
EB EB EB EB EB EB ED ED FB FB FB FB FB FB FC FC
EB EB EB EB EB EB ED ED FB FB FB FB FB FC FF FF
EB EB EB EB EB EB EM EM FB FB FB FB FB FD FG FG
EC EC EC EC EC EC EG
EC EC EC EC EC EC EG
EC EC EC EC EC EC
EC EC EC EC EC EC
EB EB EB EB EC EM
EB EB EB EB EC EG
EB EB EB EB EC EG
EC EC EC EC EC EG
ED ED ED ED EC
EE EE EE EE ED
EF EF EF EF ED
EF EF EF EG ED
FB FB FB FB FB FD
FC FC FC FC FC FD
FC FC FC FC FC FD
FC FC FC FC FC FD
FC FC FC FC FC FD
FD FD FD FD FD FD
FD FD FD FD FD FD
FD FD FD FD FD FD
FD FD FD FD FD FF
FD FD FD FD FD FG
FF FF FF FF FF FL
FH FH FH FH FH FM
CB CB CB CD
CB CB CB
CB CB CB
DG DG DG DG DD
CB CB CB
DG DG DG DG DE
CB CB CB
DD DD DD DD DE
DD DD DD DG DH
DD DD DD DG DH
DD DD DD DG
DD DD DD DG
1
1
1
2
2
3
3
4
C
1206
X
106
K
4
R
A
C
AUTO
Case Size Specification/ Capacitance Capacitance
Failure Rate/
Packaging/Grade
Ceramic
Voltage
Dielectric
Termination Finish
(L" x W")
Series
Code (pF)
Tolerance
Design
(C-Spec)
0603
X = Flexible 2 significant
J = ±5%
K = ±10%
M = ±20%
9 = 6.3 V
8 = 10 V
4 = 16 V
3 = 25 V
5 = 50 V
1 = 100 V
2 = 200 V
R = X7R A = N/A
C = 100% Matte Sn Blank = Bulk
0805
Termination
digits +
number of
zeros
L = SnPb (5%
minimum)
TU = 7" Reel Unmarked
1206
TM = 7" Reel Marked
5
6
8
1210
AUTO = Automotive
Grade 7" Reel Unmarked
1808
1812
1825
C
2220
A = 250 V
2225
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012
5
Roll Over for
Order Info.
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Table 1A – Capacitance Range/Selection Waterfall (0603 – 1210 Case Sizes) cont'd
Series
Voltage Code
Voltage DC
C0603X
C0805X
C1206X
C1210X
Cap
Code
9
8
4
3
5
1
2
9
8
4
3
5
1
2
A
9
8
4
3
5
1
2
A
9
8
4
3
5
1
2
A
Cap
Cap Tolerance
Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions
10 µF
12 µF
15 µF
18 µF
22 µF
106
126
156
186
226
J
J
J
J
J
K
K
K
K
K
M
M
M
M
M
EH EH EH
FH FH FH FS
FS FS
Voltage DC
Voltage Code
Series
Cap
Code
9
8
4
3
5
1
2
9
8
4
3
5
1
2
A
9
8
4
3
5
1
2
A
9
8
4
3
5
1
2
A
Cap
C0603X
C0805X
C1206X
C1210X
Table 1B – Capacitance Range/Selection Waterfall (1808 – 2225 Case Sizes)
Series
Voltage Code
Voltage DC
C1808X
C1812X
C1825X
C2220X
C2225X
Cap
Code
5
1
2
A
3
5
1
2
A
5
1
2
A
3
5
1
2
A
5
1
2
A
Cap
Cap Tolerance
Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions
4,700 pF
5,600 pF
6,800 pF
8,200 pF
10,000 pF
12,000 pF
15,000 pF
18,000 pF
22,000 pF
27,000 pF
33,000 pF
39,000 pF
47,000 pF
56,000 pF
68,000 pF
82,000 pF
0.10 µF
0.12 µF
0.15 µF
0.18 µF
0.22 µF
0.27 µF
0.33 µF
0.
0.
472
562
682
822
103
123
153
183
223
273
333
393
473
563
683
823
104
124
154
184
224
274
334
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
LD
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GE
GF
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GB
GE
GG
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
HB
KC
KC
KC
KC
KC
KC
KC
KC
KC
KB
KB
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
KC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
JC
GB GG GG
GG GG GG
GG GG GG
C
1206
X
106
K
4
R
A
C
AUTO
0.
0.
0.
1
Case Size Specification/ Capacitance Capacitance
Failure Rate/
Packaging/Grade
Ceramic
Voltage
Dielectric
Termination Finish
(L" x W")
Series
Code (pF)
Tolerance
Design
(C-Spec)
0603
X = Flexible 2 significant
J = ±5%
9 = 6.3 V
8 = 10 V
4 = 16 V
3 = 25 V
5 = 50 V
1 = 100 V
R = X7R A = N/A
C = 100% Matte Sn Blank = Bulk
1
1
1
2
0805
Termination
digits +
number of
zeros
K = ±10%
M = ±20%
L = SnPb (5%
TU = 7" Reel Unmarked
1206
minimum)
TM = 7" Reel Marked
12
10
AUTO = Automotive
1808
Grade 7" Reel Unmarked
1812
C
1825
2 = 200 V
A = 250 V
2220
2225
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012
6
Roll Over for
Order Info.
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Table 1B – Capacitance Range/Selection Waterfall (1808 – 2225 Case Sizes) cont'd
Series
Voltage Code
Voltage DC
C1808X
C1812X
C1825X
C2220X
C2225X
Cap
Code
5
1
2
A
3
5
1
2
A
5
1
2
A
3
5
1
2
A
5
1
2
A
Cap
Cap Tolerance
Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions
2.7 µF
3.3 µF
3.9 µF
4.7 µF
5.6 µF
6.8 µF
8.2 µF
10 µF
12 µF
15 µF
18 µF
22 µF
275
335
395
475
565
685
825
106
126
156
186
226
J
J
J
J
J
J
J
J
J
J
J
J
K
K
K
K
K
K
K
K
K
K
K
K
M
M
M
M
M
M
M
M
M
M
M
M
GK
GK
GK
JF
JO
JO
JO
Voltage DC
Cap
Code
Voltage Code
5
1
2
A
3
5
1
2
A
5
1
2
A
3
5
1
2
A
5
1
2
A
Cap
Series
C1808X
C1812X
C1825X
C2220X
C2225X
Table 2 – Chip Thickness/Packaging Quantities
Paper Quantity
Plastic Quantity
Thickness Case Thickness ±
Code
Size
Range (mm)
7" Reel
13" Reel
7" Reel
13" Reel
CB
CD
DC
DD
DE
DG
DH
EB
EC
EN
ED
EE
EF
0603
0603
0805
0805
0805
0805
0805
1206
1206
1206
1206
1206
1206
1206
1206
0.80 ± 0.07
0.80 ± 0.15
0.78 ± 0.10
0.90 ± 0.10
1.00 ± 0.10
1.25 ± 0.15
1.25 ± 0.20
0.78 ± 0.10
0.90 ± 0.10
0.95 ± 0.10
1.00 ± 0.10
1.10 ± 0.10
1.20 ± 0.15
1.25 ± 0.15
1.60 ± 0.15
4,000
4,000
0
0
0
0
0
10,000
10,000
0
0
0
0
0
0
0
0
0
4,000
4,000
2,500
2,500
2,500
4,000
4,000
4,000
2,500
2,500
2,500
2,500
2,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
8,000
4,000
10,000
0
0
0
0
0
0
0
0
0
0
0
0
0
0
EM
EG
C
1206
X
106
K
4
R
A
C
AUTO
Case Size Specification/ Capacitance Capacitance
Failure Rate/
Packaging/Grade
(C-Spec)
Ceramic
Voltage
Dielectric
Termination Finish
Design
(L" x W")
Series
Code (pF)
Tolerance
0603
0805
X = Flexible 2 significant
J = ±5%
9 = 6.3 V
R = X7R A = N/A
C = 100% Matte Sn Blank = Bulk
L = SnPb (5%
minimum)
Termination
digits +
number of
zeros
K = ±10%
8 = 10 V
TU = 7" Reel Unmarked
TM = 7" Reel Marked
AUTO = Automotive
1206
M = ±20%
4 = 16 V
1210
3 = 25 V
1808
1812
5 = 50 V
1 = 100 V
Grade 7" Reel Unmarked
Th
1825
2 = 200 V
A = 250 V
2220
2225
Packa
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012
7
Roll Over for
Order Info.
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Table 2 – Chip Thickness/Packaging Quantities cont'd
Paper Quantity
7" Reel 13" Reel
Plastic Quantity
7" Reel 13" Reel
Thickness Case Thickness ±
Code
Size
Range (mm)
FH
FM
FJ
1210
1210
1210
1210
1210
1808
1812
1812
1812
1812
1812
1812
1812
1825
1825
1825
1825
2220
2220
2220
2220
2225
2225
2225
2225
1.55 ± 0.15
1.70 ± 0.20
1.85 ± 0.20
2.10 ± 0.20
2.50 ± 0.20
0.90 ± 0.10
1.00 ± 0.10
1.10 ± 0.10
1.30 ± 0.10
1.50 ± 0.10
1.55 ± 0.10
1.60 ± 0.20
1.70 ± 0.15
1.10 ± 0.15
1.15 ± 0.15
1.30 ± 0.15
1.50 ± 0.15
1.10 ± 0.15
1.30 ± 0.15
1.50 ± 0.15
2.40 ± 0.15
1.00 ± 0.15
1.10 ± 0.15
1.30 ± 0.15
1.40 ± 0.15
0
0
2,000
8,000
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2,000
2,000
2,000
1,000
2,500
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
8,000
8,000
8,000
4,000
10,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
2,000
4,000
4,000
4,000
4,000
FK
FS
LD
GB
GC
GE
GF
GG
GK
GJ
HB
HC
HD
HF
JC
JD
JF
JO
KB
KC
KD
KE
1,000
1,000
1,000
1,000
7" Reel
13" Reel
7" Reel
13" Reel
Thickness
Code
Case
Size
Thickness ±
Range (mm)
Paper Quantity
Plastic Quantity
Package quantity based on finished chip thickness specifications.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012
8
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Table 3 – Chip Capacitor Land Pattern Design Recommendations per IPC–7351
Density Level A:
Maximum (Most)
Land Protrusion (mm)
Density Level B:
Median (Nominal)
Land Protrusion (mm)
Density Level C:
Minimum (Least)
Land Protrusion (mm)
EIA
Size
Code
Metric
Size
Code
C
Y
X
V1
V2
C
Y
X
V1
V2
C
Y
X
V1
V2
0603
0805
1206
1210
1808
1812
1825
2220
2225
1608
2012
3216
3225
4520
4532
4564
5650
5664
0.85
1.00
1.60
1.60
2.25
2.10
2.15
2.85
2.85
1.25
1.35
1.65
1.65
1.85
1.80
1.80
2.10
2.10
1.10
1.55
1.90
2.80
2.30
3.60
6.90
5.50
6.90
4.00
4.40
5.90
5.90
7.40
7.00
7.10
8.80
8.80
2.10
2.60
2.90
3.80
3.30
4.60
7.90
6.50
7.90
0.75
0.90
1.50
1.50
2.15
2.00
2.05
2.75
2.75
1.05
1.15
1.45
1.45
1.65
1.60
1.60
1.90
1.90
1.00
1.45
1.80
2.70
2.20
3.50
6.80
5.40
6.80
3.10
3.50
5.00
5.00
6.50
6.10
6.20
7.90
7.90
1.50
2.00
2.30
3.20
2.70
4.00
7.30
5.90
7.30
0.65
0.80
1.40
1.40
2.05
1.90
1.95
2.65
2.65
0.85
0.95
1.25
1.25
1.45
1.40
1.40
1.70
1.70
0.90
1.35
1.70
2.60
2.10
3.40
6.70
5.30
6.70
2.40
2.80
4.30
4.30
5.80
5.40
5.50
7.20
7.20
1.20
1.70
2.00
2.90
2.40
3.70
7.00
5.60
7.00
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder
processes. KEMET only recommends wave soldering of EIA 0603, 0805, and 1206 case sizes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes.
Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification
testing based on the conditions outlined in IPC Standard 7351 (IPC–7351).
Soldering Process
Recommended Soldering Technique:
• Solder wave or solder reflow for EIA case sizes 0603, 0805, and 1206
• All other EIA case sizes are limited to solder reflow only
Recommended Soldering Profile:
• KEMET recommends following the guidelines outlined in IPC/JEDEC J–STD–020
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012
9
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Table 4 – Performance & Reliability: Test Methods and Conditions
Stress
Reference
Test or Inspection Method
Terminal Strength
JIS–C–6429
Appendix 1, Note: Force of 1.8 kg for 60 seconds.
Appendix 2, Note: Standard termination system – 2.0 mm (minimum) for all except 3 mm for C0G.
Flexible termination system – 3.0 mm (minimum).
Board Flex
JIS–C–6429
Magnification 50 X. Conditions:
a) Method B, 4 hours @ 155°C, dry heat @ 235°C
b) Method B @ 215°C category 3
Solderability
J–STD–002
c) Method D, category 3 @ 260°C
Temperature Cycling
Biased Humidity
JESD22 Method JA–104
MIL–STD–202 Method 103
1,000 Cycles (-55°C to +125°C). Measurement at 24 hours +/- 2 hours after test conclusion.
Load Humidity: 1,000 hours 85°C/85% RH and rated voltage. Add 100 K ohm resistor. Measurement
at 24 hours +/- 2 hours after test conclusion.
Low Volt Humidity: 1,000 hours 85°C/85% RH and 1.5 V. Add 100 K ohm resistor.
Measurement at 24 hours +/- 2 hours after test conclusion.
t = 24 hours/cycle. Steps 7a and 7b not required. Unpowered.
Measurement at 24 hours +/- 2 hours after test conclusion.
-55°C/+125°C. Note: Number of cycles required – 300, maximum transfer time – 20 seconds, dwell
time – 15 minutes. Air – Air.
Moisture Resistance
Thermal Shock
MIL–STD–202 Method 106
MIL–STD–202 Method 107
MIL–STD–202 Method 108
/EIA–198
High Temperature Life
1,000 hours at 125°C (85°C for X5R, Z5U and Y5V) with 2 X rated voltage applied.
Storage Life
MIL–STD–202 Method 108 150°C, 0 VDC for 1,000 hours.
Mechanical Shock
MIL–STD–202 Method 213 Figure 1 of Method 213, Condition F.
Resistance to Solvents MIL–STD–202 Method 215 Add aqueous wash chemical, OKEM Clean or equivalent.
Storage and Handling
Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other
environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term
storage. In addition, packaging materials will be degraded by high temperature– reels may soften or warp and tape peel force may
increase. KEMET recommends that maximum storage temperature not exceed 40ºC and maximum storage humidity not exceed 70%
relative humidity. Temperature fluctuations should be minimized to avoid condensation on the parts and atmospheres should be free of
chlorine and sulfur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within 1.5 years of
receipt.
Construction
Reference
Item
Material
A
B
C
D
Finish
100% Matte Sn SnPb (5% min)
Barrier Layer
Epoxy Layer
Base Metal
Ni
Ag
Cu
Termination
System
E
Inner Electrode
Dielectric Material
Ni
F
BaTiO3
Note: Image is exaggerated in order to clearly identify all components of construction.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012 10
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Capacitor Marking (Optional):
These surface mount multilayer ceramic capacitors are
normally supplied unmarked. If required, they can be marked
as an extra cost option. Marking is available on most KEMET
devices but must be requested using the correct ordering
code identifier(s). If this option is requested, two sides of the
ceramic body will be laser marked with a “K” to identify KEMET,
followed by two characters (per EIA–198 - see table below) to
identify the capacitance value. EIA 0603 case size devices are
limited to the “K” character only.
Marking appears in legible contrast. Illustrated below is an
example of an MLCC with laser marking of “KA8”, which
designates a KEMET device with rated capacitance of 100 µF.
Orientation of marking is vendor optional.
_
KA8
Laser marking option is not available on:
• C0G and Y5V dielectric devices
• EIA 0402 case size devices
• EIA 0603 case size devices with Flexible Termination option.
Capacitance (pF) For Various Alpha / Numeral Identifiers
Numeral
Alpha
Character
9
0
1
2
3
4
5
6
7
8
Capacitance (pF)
A
B
C
D
E
F
G
H
J
0.1
0.11
0.12
0.13
0.15
0.16
0.18
0.2
1 0
1.1
1 2
1 3
1 5
1 6
1 8
2 0
2 2
2.4
2.7
3 0
3 3
3 6
3 9
4 3
4.7
5.1
5 6
6 2
6 8
7 5
8 2
9.1
2 5
3 5
4 0
4 5
5 0
6 0
7 0
8 0
9 0
10
11
12
13
15
16
18
20
22
24
27
30
33
36
39
43
47
51
56
62
68
75
82
91
25
35
40
45
50
60
70
80
90
100
110
120
130
150
160
180
200
220
240
270
300
330
360
390
430
470
510
560
620
680
750
820
910
250
350
400
450
500
600
700
800
900
1,000
1,100
1,200
1,300
1,500
1,600
1,800
2,000
2,200
2,400
2,700
3,000
3,300
3,600
3,900
4,300
4,700
5,100
5,600
6,200
6,800
7,500
8,200
9,100
2,500
3,500
4,000
4,500
5,000
6,000
7,000
8,000
9,000
10,000
11,000
12,000
13,000
15,000
16,000
18,000
20,000
22,000
24,000
27,000
30,000
33,000
36,000
39,000
43,000
47,000
51,000
56,000
62,000
68,000
75,000
82,000
91,000
25,000
35,000
40,000
45,000
50,000
60,000
70,000
80,000
90,000
100,000 1,000,000
110,000 1,100,000
120,000 1,200,000
130,000 1,300,000
150,000 1,500,000
160,000 1,600,000
180,000 1,800,000
200,000 2,000,000
220,000 2,200,000
240,000 2,400,000
270,000 2,700,000
300,000 3,000,000
330,000 3,300,000
360,000 3,600,000
390,000 3,900,000
430,000 4,300,000
470,000 4,700,000
510,000 5,100,000
560,000 5,600,000
620,000 6,200,000
680,000 6,800,000
750,000 7,500,000
820,000 8,200,000
910,000 9,100,000
250,000 2,500,000
350,000 3,500,000
400,000 4,000,000
450,000 4,500,000
500,000 5,000,000
600,000 6,000,000
700,000 7,000,000
800,000 8,000,000
900,000 9,000,000
10,000,000
11,000,000
12,000,000
13,000,000
15,000,000
16,000,000
18,000,000
20,000,000
22,000,000
24,000,000
27,000,000
30,000,000
33,000,000
36,000,000
39,000,000
43,000,000
47,000,000
51,000,000
56,000,000
62,000,000
68,000,000
75,000,000
82,000,000
91,000,000
25,000,000
35,000,000
40,000,000
45,000,000
50,000,000
60,000,000
70,000,000
80,000,000
90,000,000
100,000,000
110,000,000
120,000,000
130,000,000
150,000,000
160,000,000
180,000,000
200,000,000
220,000,000
240,000,000
270,000,000
300,000,000
330,000,000
360,000,000
390,000,000
430,000,000
470,000,000
510,000,000
560,000,000
620,000,000
680,000,000
750,000,000
820,000,000
910,000,000
250,000,000
350,000,000
400,000,000
450,000,000
500,000,000
600,000,000
700,000,000
800,000,000
900,000,000
0.22
0.24
0.27
0.3
K
L
M
N
P
Q
R
S
T
U
V
W
X
Y
Z
a
0.33
0.36
0.39
0.43
0.47
0.51
0.56
0.62
0.68
0.75
0.82
0.91
0.25
0.35
0.4
b
d
e
0.45
0.5
f
m
n
0.6
0.7
t
0.8
y
0.9
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012 11
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Tape & Reel Packaging Information
KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with EIA
Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for details on
reeling quantities for commercial chips.
Bar Code Label
Anti-Static Reel
®
Embossed Plastic* or
Punched Paper Carrier.
Chip and KPS Orientation in Pocket
(except 1825 Commercial, and 1825 and 2225 Military)
KEMET
Sprocket Holes
Embossment or Punched Cavity
8 mm, 12 mm
or 16 mm Carrier Tape
Anti-Static Cover Tape
(.10 mm (.004") Maximum Thickness)
178 mm (7.00")
or
330 mm (13.00")
*EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only.
Table 5 – Carrier Tape Configuration – Embossed Plastic & Punched Paper (mm)
EIA Case Size
01005 – 0402
0603 – 1210
Tape Size (W)*
Lead Space (P1)*
8
8
2
4
1805 – 1808
12
12
12
16
8
4
≥ 1812
8
KPS 1210
8
KPS 1812 & 2220
Array 0508 & 0612
12
4
*Refer to Figures 1 & 2 for W and P1 carrier tape reference locations.
*Refer to Tables 6 & 7 for tolerance specifications.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012 12
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
T
T
P2
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
2
E
1
Po
ØDo
Ao
F
Ko
W
E
2
B
1
Bo
S
1
P
1
T
1
Embossment
For cavity size,
see Note 1 Table 4
Center Lines of Cavity
ØD
1
Cover Tape
is for tape feeder reference only,
including draft concentric about B
B
1
o
.
User Direction of Unreeling
Table 6 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
D1 Minimum
Note 1
1.0
(0.039)
R Reference S1 Minimum
T
T1
Tape Size
8 mm
D0
E1
P0
P2
Note 2
Note 3
Maximum
Maximum
25.0
(0.984)
1.5 +0.10/-0.0 (0.059
+0.004/-0.0)
1.75 ±0.10
4.0 ±0.10
2.0 ±0.05 (0.079
±0.002)
0.600
(0.024)
0.600
(0.024)
0.100
(0.004)
12 mm
16 mm
(0.069 ±0.004) (0.157 ±0.004)
1.5
(0.059)
30
(1.181)
Variable Dimensions — Millimeters (Inches)
B1 Maximum
Note 4
4.35
(0.171)
E2
T2
W
Tape Size
8 mm
Pitch
F
P1
A0,B0 & K0
Minimum
6.25
(0.246)
Maximum
2.5
(0.098)
Maximum
8.3
(0.327)
3.5 ±0.05
(0.138 ±0.002) (0.157 ±0.004)
4.0 ±0.10
Single (4 mm)
Single (4 mm) &
Double (8 mm)
8.2
10.25
5.5 ±0.05
8.0 ±0.10 (0.315
±0.004)
4.6
12.3
12 mm
16 mm
Note 5
(0.323)
(0.404)
(0.217 ±0.002)
(0.181)
(0.484)
12.1
(0.476)
14.25
(0.561)
5.5 ±0.05
(0.217 ±0.002)
8.0 ±0.10 (0.315
±0.004)
4.6
(0.181)
16.3
(0.642)
Triple (12 mm)
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
2. The tape with or without components shall pass around R without damage (see Figure 6).
3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 3).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 4).
(e) for KPS Series product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket.
(f) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012 13
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Figure 2 – Punched (Paper) Carrier Tape Dimensions
T
P2
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
E
1
Po
ØDo
0
A
F
W
2
E
0
B
Bottom Cover Tape
P
1
G
Cavity Size,
See
1
T
1
T
Top Cover Tape
Center Lines of Cavity
Note 1, Table 7
Bottom Cover Tape
User Direction of Unreeling
Table 7 – Punched (Paper) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
R Reference
Note 2
Tape Size
8 mm
D0
E1
P0
P2
T1 Maximum
G Minimum
1.5 +0.10 -0.0
(0.059 +0.004 -0.0)
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
2.0 ±0.05
(0.079 ±0.002) (0.004) Maximum
0.10
0.75
(0.030)
25
(0.984)
Variable Dimensions — Millimeters (Inches)
Tape Size
8 mm
Pitch
E2 Minimum
F
P1
T Maximum
W Maximum
A0 B0
2.0 ±0.05
(0.079 ±0.002)
4.0 ±0.10
8.3
(0.327)
8.3
Half (2 mm)
Single (4 mm)
6.25
(0.246)
3.5 ±0.05
(0.138 ±0.002)
1.1
(0.098)
Note 1
8 mm
(0.157 ±0.004)
(0.327)
1. The cavity defined by A0, B0 and T shall surround the component with sufficient clearance that:
a) the component does not protrude beyond either surface of the carrier tape.
b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
c) rotation of the component is limited to 20° maximum (see Figure 3).
d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4).
e) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements.
2. The tape with or without components shall pass around R without damage (see Figure 6).
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012 14
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Packaging Information Performance Notes
1. Cover Tape Break Force: 1.0 Kg minimum.
2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width
8 mm
Peel Strength
0.1 to 1.0 Newton (10 to 100 gf)
0.1 to 1.3 Newton (10 to 130 gf)
12 and 16 mm
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180°
from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute.
3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA
Standards 556 and 624.
Figure 3 – Maximum Component Rotation
°
T
Maximum Component Rotation
Top View
Maximum Component Rotation
Side View
Typical Pocket Centerline
Tape
Maximum
°
°
T
s
Width (mm) Rotation (
)
8,12
16 – 200
20
10
Bo
Tape
Maximum
°
S
Width (mm) Rotation (
)
8,12
16 – 56
72 – 200
20
10
5
Typical Component Centerline
Ao
Figure 4 – Maximum Lateral Movement
Figure 5 – Bending Radius
Embossed
Carrier
Punched
Carrier
8 mm & 12 mm Tape
16 mm Tape
0.5 mm maximum
0.5 mm maximum
1.0 mm maximum
1.0 mm maximum
R
Bending
Radius
R
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012 15
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Figure 6 – Reel Dimensions
Full Radius,
W3 (Includes
flange distortion
at outer edge)
Access Hole at
Slot Location
(Ø 40 mm minimum)
See Note
W
2 (Measured at hub)
D
(See Note)
A
N
C
(Arbor hole
W
1 (Measured at hub)
diameter)
If present,
tape slot in core
for tape start:
2.5 mm minimum width x
10.0 mm minimum depth
B
(see Note)
Note: Drive spokes optional; if used, dimensions B and D shall apply.
Table 8 – Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
8 mm
A
B Minimum
C
D Minimum
178 ±0.20
(7.008 ±0.008)
or
330 ±0.20
(13.000 ±0.008)
1.5
(0.059)
13.0 +0.5/-0.2
(0.521 +0.02/-0.008)
20.2
(0.795)
12 mm
16 mm
Variable Dimensions — Millimeters (Inches)
Tape Size
8 mm
N Minimum
W1
W2 Maximum
W3
8.4 +1.5/-0.0
(0.331 +0.059/-0.0)
14.4
(0.567)
50
(1.969)
12.4 +2.0/-0.0
18.4
Shall accommodate tape width
without interference
12 mm
16 mm
(0.488 +0.078/-0.0)
(0.724)
16.4 +2.0/-0.0
(0.646 +0.078/-0.0)
22.4
(0.882)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012 16
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Figure 7 – Tape Leader & Trailer Dimensions
Embossed Carrier
Carrier Tape
Round Sprocket Holes
Punched Carrier
8 mm & 12 mm only
START
END
Top Cover Tape
Elongated Sprocket Holes
(32 mm tape and wider)
100 mm
Minimum Leader
400 mm Minimum
Trailer
160 mm Minimum
Components
Top Cover Tape
Figure 8 – Maximum Camber
Elongated sprocket holes
(32 mm & wider tapes)
Carrier Tape
Round Sprocket Holes
1 mm Maximum, either direction
Straight Edge
250 mm
Bulk Cassette Packaging (Ceramic Chips Only)
Meets Dimensional Requirements IEC–286 and EIAJ 7201
Unit mm *Reference
53 3*
10*
1.5 ± 00.1
2.0 ± 00.1
3.0 ± 00.2
5 0*
110 ± 0.7
Capacitor Dimensions for Bulk Cassette
Cassette Packaging – Millimeters
EIA Size Metric Size
S Separation
Minimum
Number of
Pieces/Cassette
L Length
W Width
B Bandwidth
T Thickness
Code
Code
0402
1005
1.0 ±0.05
1.6 ±0.07
0.5 ±0.05
0.8 ±0.07
0.2 to 0.4
0.2 to 0.5
0.3
0.5 ±0.05
0.8 ±0.07
50,000
0603
1608
0.7
15,000
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012 17
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Geneva, Switzerland
Tel: 41-22-715-0100
Northeast Asia
Hong Kong
Tel: 852-2305-1168
2835 KEMET Way
Simpsonville, SC 29681
Paris, France
Tel: 33-1-4646-1009
Shenzhen, China
Tel: 86-755-2518-1306
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
Sasso Marconi, Italy
Tel: 39-051-939111
Beijing, China
Tel: 86-10-5829-1711
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Milan, Italy
Tel: 39-02-57518176
Shanghai, China
Tel: 86-21-6447-0707
Corporate Offices
Fort Lauderdale, FL
Tel: 954-766-2800
Rome, Italy
Tel: 39-06-23231718
Taipei, Taiwan
Tel: 886-2-27528585
Madrid, Spain
Tel: 34-91-804-4303
North America
Southeast Asia
Singapore
Tel: 65-6586-1900
Southeast
Lake Mary, FL
Tel: 407-855-8886
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Penang, Malaysia
Tel: 60-4-6430200
Northeast
Wilmington, MA
Tel: 978-658-1663
Bangalore, India
Tel: 91-806-53-76817
Dortmund, Germany
Tel: 49-2307-3619672
West Chester, PA
Tel: 610-692-4642
Kwidzyn, Poland
Tel: 48-55-279-7025
Central
Novi, MI
Tel: 248-994-1030
Northern Europe
Bishop’s Stortford, United Kingdom
Tel: 44-1279-757201
Carmel, IN
Tel: 317-706-6742
Weymouth, United Kingdom
Tel: 44-1305-830747
West
Milpitas, CA
Tel: 408-433-9950
Coatbridge, Scotland
Tel: 44-1236-434455
Mexico
Zapopan, Jalisco
Tel: 52-33-3123-2141
Färjestaden, Sweden
Tel: 46-485-563934
Espoo, Finland
Tel: 358-9-5406-5000
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012 18
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Other KEMET Resources
Tools
Resource
Location
Configure A Part: CapEdge
SPICE & FIT Software
http://capacitoredge.kemet.com
http://www.kemet.com/spice
http://www.kemet.com/keask
Search Our FAQs: KnowledgeEdge
Product Information
Resource
Location
Products
Technical Resources (Including Soldering Techniques)
RoHS Statement
http://www.kemet.com/products
http://www.kemet.com/technicalpapers
http://www.kemet.com/rohs
Quality Documents
http://www.kemet.com/qualitydocuments
Product Request
Resource
Location
http://www.kemet.com/sample
http://www.kemet.com/kits
Sample Request
Engineering Kit Request
Contact
Resource
Location
Website
Contact Us
Investor Relations
Call Us
www.kemet.com
http://www.kemet.com/contact
http://www.kemet.com/ir
1-877-MyKEMET
Twitter
http://twitter.com/kemetcapacitors
Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) are subject to change without notice.
All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute – and we
specifically disclaim – any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite
experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the
use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained.
Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur.
Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or
redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012 19
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
Flexible Termination System (FT-CAP), X7R Dielectric, 6.3 – 250 VDC (Commercial Grade & Automotive Grade)
Digitally signed by Jeannette Calvo
DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corp., ou=Marketing
Communications, cn=Jeannette Calvo,
email=jeannettecalvo@kemet.com
Date: 2012.10.09 16:49:10 -04'00'
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
C1013_X7R_FT-CAP_SMD • 10/3/2012 20
相关型号:
C0805X824K8RAC7867
Ceramic Capacitor, Ceramic, 10V, 10% +Tol, 10% -Tol, X7R, -/+15ppm/Cel TC, 0.82uF, 0805,
KEMET
C0805X824K9RAC7867
Ceramic Capacitor, Ceramic, 6.3V, 10% +Tol, 10% -Tol, X7R, -/+15ppm/Cel TC, 0.82uF, 0805,
KEMET
C0805X824K9RACAUTO
Ceramic Capacitor, Multilayer, Ceramic, 6.3V, 10% +Tol, 10% -Tol, X7R, 15% TC, 0.82uF, Surface Mount, 0805, CHIP
KEMET
C0805X824K9RACTM
Ceramic Capacitor, Multilayer, Ceramic, 6.3V, 10% +Tol, 10% -Tol, X7R, 15% TC, 0.82uF, Surface Mount, 0805, CHIP, ROHS COMPLIANT
KEMET
C0805X824K9RACTU
Ceramic Capacitor, Multilayer, Ceramic, 6.3V, 10% +Tol, 10% -Tol, X7R, 15% TC, 0.82uF, Surface Mount, 0805, CHIP
KEMET
©2020 ICPDF网 联系我们和版权申明