C410C105J5N5TA7200 [KEMET]
Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 - 50 VDC (Commercial & Automotive Grade);型号: | C410C105J5N5TA7200 |
厂家: | KEMET CORPORATION |
描述: | Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 - 50 VDC (Commercial & Automotive Grade) |
文件: | 总9页 (文件大小:2550K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Axial Through-Hole Multilayer Ceramic Capacitors
Aximax, 400 Series, Axial, Conformally Coated, X8L
Dielectric, 25 – 50 VDC (Commercial & Automotive Grade)
Overview
KEMET’s Aximax conformally coated axial through-hole
ceramic capacitors in X8L dielectric feature a 150°C
maximum operating temperature and is considered
"general purpose high temperature". These components
are fixed, ceramic dielectric capacitors suited for high
temperature bypass and decoupling applications or
frequency discriminating circuits where Q and stability of
capacitance characteristics are not critical. X8L exhibits
a predictable change in capacitance with respect to time
and voltage and boasts a minimal change in capacitance
with reference to ambient temperature up to 125°C. Beyond
125°C X8L displays a wider variation in capacitance.
Capacitance change is limited to ±15% from -55°C to
+125°C and +15, -40% from 125°C to 150°C.
In addition to commercial grade, automotive grade devices
are available and meet the demanding Automotive Electronics
Council's AEC-Q200 qualification requirements.
These devices meet the flame test requirements outlined in
UL Standard 94V-0.
Driven by the demand for a more robust and reliable
component, X8L dielectric capacitors were developed for
critical applications where reliability at higher operating
temperatures are a concern. These capacitors are widely
used in automotive circuits as well as general high
temperature applications.
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
Ordering Information
C
410
C
105
K
3
N
5
T
A
7200
Rated
Style Specification/ Capacitance Capacitance
Lead
Failure
Rate
Packaging/Grade
(C-Spec)
Ceramic
Voltage Dielectric Design
(VDC)
/Size
Series
Code (pF)
Tolerance1
Finish2
410 C = Standard Two significant J = ±5%
3 = 25 V
N =
X8L
5 =
T = 100% A = N/A Blank = Bulk
430
digits and
number of
zeros
K = ±10% 5 = 50 V
M = ±20%
Multilayer Matte Sn
H = SnPb
7200 = 12" Reel
7293 = Ammo pack
(60/40)
9170 = Automotive grade
9170 7200 = Auto 12" Reel
9170 7293 = Auto Ammo pack
1 Additional capacitance Tolerance offerings may be available. Contact KEMET for details.
2 Lead materials:
Standard: 100% matte tin (Sn) with nickel (Ni) underplate and steel core ( “T” designation).
ꢀ Alternativeꢀ1:ꢀ60%ꢀtinꢀ(Sn)/40%ꢀleadꢀ(Pb)ꢀfinishꢀwithꢀcopper-cladꢀsteelꢀcoreꢀ(ꢀ“H”ꢀdesignation).
ꢀ Additionalꢀleadꢀfinishꢀoptionsꢀmayꢀbeꢀavailable.ꢀContactꢀKEMETꢀforꢀdetails
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1072_AXIMAX_X8L • 10/17/2016
1
Axial Through-Hole Multilayer Ceramic Capacitors
Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 – 50 VDC (Commercial & Automotive Grade)
Dimensions – Millimeters (Inches)
LL
L
D
0ꢀ0ꢁ5 (0ꢀꢂ8)
Maximum
LD
L
D
LL
Style/
Size
LD
Series
Length
Diameter
Maximum
Lead Length
Minimum
Lead Diameter
Maximum
0.170 (4.32)
0.240 (6.10)
C41X
C43X
410
430
0.095 (2.31)
0.020+0.001/−0.003
(0.51+0.025/−0.076)
1.0 (25.4)
0.150 (3.81)
Benefits
• Axial through-hole form factor
• Conformally coated
• Operating temperature range of −55°C to +150°C
• Lead (Pb)-free, RoHS and REACH compliant
• DC voltage ratings of 25 V and 50 V
• Commercial and Automotive (AEC-Q200) grades available
• Non-polar device, minimizing installation concerns
• 100% pure matte tin-plated lead finish allowing for
excellent solderability
• SnPb-plated lead finish option available upon request
(60/40)
• Capacitance offerings ranging from 0.1 μF up to 2.2 μF
• Available capacitance tolerances of ±5%, ±10% and ±20%
• Encapsulation meets flammability standard UL 94V–0
Applications
Typical applications include use in extreme environments such as down-hole oil exploration, under-hood automotive,
aerospace and defense.
Application Notes
These devices are not recommended for use in overmold applications and/or processes.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1072_AXIMAX_X8L • 10/17/2016
2
Axial Through-Hole Multilayer Ceramic Capacitors
Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 – 50 VDC (Commercial & Automotive Grade)
Qualification/Certification
Commercial Grade products are subject to internal qualification. Details regarding test methods and conditions are
referenced in Table 4, Performance & Reliability.
Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details
regarding test methods and conditions are referenced in document AEC–Q200, Stress Test Qualification for Passive
Components. For additional information regarding the Automotive Electronics Council and AEC–Q200, please visit their
website at www.aecouncil.com.
Environmental Compliance
Lead (Pb)-free, RoHS, and REACH compliant without exemptions (excluding SnPb termination finish option).
Electrical Parameters/Characteristics
Item
Parameters/Characteristics
Operating Temperature Range
−55°C to +150°C
Capacitance Change with Reference to
+25°C and 0 VDC Applied (TCC)
±15%(−55ºC to 125ºC) +15%, −40% (125ºC to 150ºC)
Aging Rate (Maximum % Capacitance Loss/Decade Hour)
Dielectric Withstanding Voltage (DWV)
3.0%
250% of rated voltage
(5±1 seconds and charge/discharge not exceeding 50 mA)
2.5%
Dissipation Factor (DF) Maximum Limit at 25ºC
Insulation Resistance (IR) Limit at 25°C
1,000 megohm microfarads or 100 GΩ
(Rated voltage applied for 120±5 seconds at 25°C)
ToꢀobtainꢀIRꢀlimit,ꢀdivideꢀMΩ-µFꢀvalueꢀbyꢀtheꢀcapacitanceꢀandꢀcompareꢀtoꢀGΩꢀlimit.ꢀSelectꢀtheꢀlowerꢀofꢀtheꢀtwoꢀlimits.
Capacitanceꢀandꢀdissipationꢀfactorꢀ(DF)ꢀmeasuredꢀunderꢀtheꢀfollowingꢀconditions:
ꢀ
ꢀ
1ꢀMHzꢀ±100ꢀkHzꢀandꢀ1.0ꢀ±0.2ꢀVrmsꢀifꢀcapacitanceꢀ≤ꢀ1,000ꢀpF
1ꢀkHzꢀ±50ꢀHzꢀandꢀ1.0ꢀ±0.2ꢀVrmsꢀifꢀcapacitanceꢀ>ꢀ1,000ꢀpF
Note:ꢀWhenꢀmeasuringꢀcapacitanceꢀitꢀisꢀimportantꢀtoꢀensureꢀtheꢀsetꢀvoltageꢀlevelꢀisꢀheldꢀconstant.ꢀTheꢀHP4284ꢀandꢀAgilentꢀE4980ꢀhaveꢀaꢀfeatureꢀknownꢀ
as Automatic Level Control (ALC). The ALC feature should be switched to "ON."
Post Environmental Limits
High Temperature Life, Biased Humidity, Moisture Resistance
Rated DC
Voltage
Capacitance Dissipation Factor Capacitance
Insulation
Dielectric
X8L
Value
(Maximum %)
Shift
Resistance
25
50
5.0
10% of Initial
Limit
All
±20%
3.0
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1072_AXIMAX_X8L • 10/17/2016
3
Axial Through-Hole Multilayer Ceramic Capacitors
Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 – 50 VDC (Commercial & Automotive Grade)
Table 1A - C410 Style/Size (0.095" Diameter x 0.170" L), Capacitance Range Waterfall
C410 Style/Size (0.095" Diameter x 0.170" L)
Rated Voltage (VDC)
Voltage Code
25
3
50
5
Capacitance
Tolerance
Capacitance
Capacitance Code (Available Capacitance)
0.1µF
0.12µF
0.15µF
0.18µF
0.22µF
0.27µF
0.33µF
0.39µF
0.47µF
0.56µF
0.68µF
104
124
154
184
224
274
334
394
474
564
684
104
124
154
184
224
J = ±5%
K = ±10%
M = ±20%
Rated Voltage (VDC)
Voltage Code
25
3
50
5
Table 1B - C430 Style/Size (0.150" Diameter x 0.290" L), Capacitance Range Waterfall
C430 Style/Size (0.150" Diameter x 0.290" L)
Rated Voltage (VDC)
Voltage Code
25
3
50
5
Capacitance
Tolerance
Capacitance
Capacitance Code (Available Capacitance)
0.33µF
0.39µF
0.47µF
0.82µF
1.0µF
1.2µF
1.5µF
1.8µF
2.2µF
334
394
474
824
105
125
155
185
225
J = ±5%
K = ±10%
M = ±20%
Rated Voltage (VDC)
Voltage Code
25
3
50
5
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1072_AXIMAX_X8L • 10/17/2016
4
Axial Through-Hole Multilayer Ceramic Capacitors
Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 – 50 VDC (Commercial & Automotive Grade)
Soldering Process
Recommended Soldering Technique:
• Solder Wave
• Hand Soldering (Manual)
Recommended Soldering Profile:
• Optimum Wave Solder Profile
Solder ꢈave ꢆeaꢊ
Temperature 2ꢃ0ꢋC
ꢇntrance to Solder ꢈave
ꢇxit from Solder ꢈave
(Time in ꢈave – 2 to 4 Seconds)
ꢄlux ꢅone
ꢆreheat ꢅone
Hot Air Deꢉridging
250
225
200
ꢁꢀ5
ꢁ50
ꢁ25
ꢁ00
ꢀ5
ꢇxit from
Solder
Machine
80ꢋC
ꢇntrance to
ꢏn-Line Cleaner
ꢇxit from
to ꢁ20ꢋC
ꢄree
Air
Cool
ꢏn-Line Cleaner
(time in cleaner
may ꢉe less)
ꢌottom Side
Temperature
ꢍange
ꢇntrance
to Solder
Machine
ꢏmmersion in
Cleaning
Vapor
ꢁ50ꢋC
Maximum
Top Side
ꢎominal
50
25
0
ꢁ
2
ꢂ
4
5
ꢃ
Time (Minutes)
• Hand Soldering (Manual)
Manual Solder Profile with Pre-heating
Soldering
Gradual Cooling
Delta T ꢈ ꢉ ꢂ20ꢅC
Gradual ꢀreheat
ꢁ0 – ꢂ20 Seconds
ꢃecommend 2ꢄ5ꢅCꢆsecond
KEMET recommends following the guidelines and techniques outlined in technical bulletins F2103 and F9207.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1072_AXIMAX_X8L • 10/17/2016
5
Axial Through-Hole Multilayer Ceramic Capacitors
Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 – 50 VDC (Commercial & Automotive Grade)
Table 2 – Performance & Reliability: Test Methods and Conditions
Stress
Reference
Test or Inspection Method
Magnification 50 X. Conditions:
a) Method A, at 235°C, Category 3
Solderability
J–STD–002
Temperature Cycling
JESD22 Method JA–104 5 cycles (−55°C to +150°C), measurement at 24 hours ±2 hours after test conclusion.
Load humidity: 1,000 hours 85°C/85% RH and rated voltage. Add 100 K ohm resistor.
MIL–STD–202 Method
Measurement at 24 hours ±2 hours after test conclusion.
Biased Humidity
Low volt humidity: 1,000 hours 85°C/85% RH and 1.5 V. Add 100 K ohm resistor.
103
Measurement at 24 hours ±2 hours after test conclusion.
MIL–STD–202 Method
t = 24 hours/cycle. Steps 7a and 7b not required. Unpowered.
Moisture Resistance
Thermal Shock
Measurement at 24 hours ±2 hours after test conclusion.
106
MIL–STD–202 Method
−55°C/+150°C. Note: Number of cycles required = 300. Maximum transfer time = 20
seconds. Dwell time – 15 minutes. Air – Air.
107
MIL–STD–202 Method
108
High Temperature Life
1,000 hours at 150°C with 2 X rated voltage applied.
/EIA–198
MIL–STD–202 Method
108
Storage Life
Vibration
150°C, 0 VDC, for 1,000 hours.
5 g for 20 minutes, 12 cycles each of 3 orientations. Note: Use 8"X5" PCB .031" thick 7
secure points on one long side and 2 secure points at corners of opposite sides. Parts
mounted within 2" from any secure point. Test from 10 – 2,000 Hz.
MIL–STD–202 Method
204
Resistance to Soldering MIL–STD–202 Method
Condition B. No preheat of samples. Note: single wave solder – procedure 2.
Heat
210
MIL–STD–202 Method
Terminal Strength
Conditions A (454g), Condition C (227g)
211
MIL–STD–202 Method
213
Mechanical Shock
Figure 1 of Method 213, Condition C.
MIL–STD–202 Method
215
Resistance to Solvents
Add aqueous wash chemical – OKEM Clean or equivalent.
Storage & Handling
The un-mounted storage life of a through-hole (leaded) ceramic capacitor is dependent upon storage and atmospheric
conditions as well as packaging materials. While the ceramic chips enveloped under the epoxy coating themselves are quite
robust in most environments, solderability of the wire lead on the final epoxy-coated product will be degraded by exposure
to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be
degraded by high temperature and exposure to direct sunlight – reels may soften or warp, and tape peel force may increase.
KEMET recommends storing the un-mounted capacitors in their original packaging, in a location away from direct sunlight,
and where the temperature and relative humidity do not exceed 40 degrees centigrade and 70% respectively. For optimum
solderability, capacitor stock should be used promptly, preferably within 18 months of receipt. For applications requiring
pre-tinning of components, storage life may be extended if solderability is verified. Before cleaning, bonding or molding these
devices, it is important to verify that your process does not affect product quality and performance. KEMET recommends
testing and evaluating the performance of a cleaned, bonded or molded product prior to implementing and/or qualifying any
of these processes.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1072_AXIMAX_X8L • 10/17/2016
6
Axial Through-Hole Multilayer Ceramic Capacitors
Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 – 50 VDC (Commercial & Automotive Grade)
Construction
Detailed Cross Section
ꢆinish Layer
(Sn)
ꢆinish Layer
(Sn)
Dielectric Material
(ꢀaTiꢁꢂ)
ꢄpoxy
ꢄncapsulation
ꢀarrier Layer
(ꢅi)
ꢀarrier Layer
(ꢅi)
ꢄxternal ꢄlectrode
(Cu)
ꢄxternal ꢄlectrode
(Cu)
ꢃnner ꢄlectrodes
(ꢅi)
ꢄpoxy
ꢄncapsulation
Lead ꢏire
Lead Attach Solder
(Snꢇ5ꢈSꢉ5)
Std
Alt ꢊ
Alt 2
Core Metal
Steel
Cu
ꢎ
ꢅi
Cu
ꢀarrier Layer
ꢊ00ꢌ ꢋ0ꢌ Sn ꢋ0ꢌ Sn
Matte Sn 40ꢌ ꢍꢉ 40ꢌ ꢍꢉ
ꢆinish Layer
ꢃnner ꢄlectrodes
(ꢅi)
Dielectric
Material (ꢀaTiꢁꢂ)
ꢃnner ꢄlectrodes
(ꢅi)
Marking
Voltage Code
ꢀꢁMꢁT ꢂD
Capacitance Code
Dielectric Code
Capacitance
Tolerance Code
15
20
Manufacturing Year:
15 = 2015
Manufacturing Week:
20 = Week 20
(of mfg. calendar year)
Lot Code
Date Code
Packaging Quantities
Ammo Pack Reel Quantity
Style/
Size
Standard Bulk
Quantity
Quantity
Maximum
(12" Reel)
Maximum
410
430
300/Box
200/Box
4000
5000
2000
2500
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1072_AXIMAX_X8L • 10/17/2016
7
Axial Through-Hole Multilayer Ceramic Capacitors
Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 – 50 VDC (Commercial & Automotive Grade)
Tape & Reel Packaging Information
KEMET offers standard reeling of molded and conformally
coated axial leaded ceramic capacitors for automatic insertion
or lead forming machines in accordance with EIA standard
296. KEMET’s internal specification four-digit suffix, 7200, is
placed at the end of the part number to designate tape and reel
packaging, e.g., C410C104Z5U5CA7200.
Paper (50 lb.) test minimum is inserted between the layers
of capacitors wound on reels for component pitch ≤ 0.400".
Capacitor lead length may extend only a maximum of .0625"
(1.59 mm) beyond the tapes’ edges. Capacitors are centered in
a row between the two tapes and will deviate only ± 0.031" (0.79
mm) from the row center. A minimum of 36" (91.5 cm) leader
tape is provided at each finished length of taped components.
Universal splicing clips are used to connect the tape.
Table 3 – Ceramic Axial Tape and Reel Dimensions
Metric will govern
Dimensions — Millimeters (Inches)
Symbol Reference Table
Axial Capacitor
Body Diameter
A
B
A
B
Component Pitch
Inside Tape Spacing
±1.5 (0.059)*
±0.5 (0.020)
0.0 to 5.0
(0.0 to 0.197)
5.0 (0.197)
52.4 (2.062)
* Inside tape spacing dimension (B) is determined by the body diameter of the capacitor.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1072_AXIMAX_X8L • 10/17/2016
8
Axial Through-Hole Multilayer Ceramic Capacitors
Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 – 50 VDC (Commercial & Automotive Grade)
KEMET Electronic Corporation Sales Offices
For a complete list of our global sales offices, please visit www.kemet.com/sales.
Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for
checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such
applications, but are not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use.
The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any
technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no
obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component
failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards
(such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or
property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other
measures may not be required.
KEMET is a registered trademark of KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1072_AXIMAX_X8L • 10/17/2016
9
相关型号:
C410C105J5N5TA7293
Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 - 50 VDC (Commercial & Automotive Grade)
KEMET
C410C105J5N5TA9170
Aximax, 400 Series, Axial, Conformally Coated, X8L Dielectric, 25 - 50 VDC (Commercial & Automotive Grade)
KEMET
C410C105J5R5HA7200
Aximax, 400 Series, Conformally Coated, X7R Dielectric, 25 - 250 VDC (Commercial Grade)
KEMET
C410C105J5R5HA7293
Aximax, 400 Series, Conformally Coated, X7R Dielectric, 25 - 250 VDC (Commercial Grade)
KEMET
C410C105J5R5TA7200
Aximax, 400 Series, Conformally Coated, X7R Dielectric, 25 - 250 VDC (Commercial Grade)
KEMET
C410C105J5R5TA7293
Aximax, 400 Series, Conformally Coated, X7R Dielectric, 25 - 250 VDC (Commercial Grade)
KEMET
C410C105JAR5HA7200
Aximax, 400 Series, Conformally Coated, X7R Dielectric, 25 - 250 VDC (Commercial Grade)
KEMET
C410C105JAR5HA7293
Aximax, 400 Series, Conformally Coated, X7R Dielectric, 25 - 250 VDC (Commercial Grade)
KEMET
C410C105JAR5TA7200
Aximax, 400 Series, Conformally Coated, X7R Dielectric, 25 - 250 VDC (Commercial Grade)
KEMET
C410C105JAR5TA7293
Aximax, 400 Series, Conformally Coated, X7R Dielectric, 25 - 250 VDC (Commercial Grade)
KEMET
©2020 ICPDF网 联系我们和版权申明