C921U332MZVDBA7317_技术文档

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc,

Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Overview

KEMET’s 900 Series encapsulated radial through-hole ceramic

disc capacitors are speciﬁcally designed for interference-

suppression AC line ﬁltering applications. Having internationally

recognized safety certiﬁcations, these capacitors are well-suited

for applications that require keeping potentially disruptive or

damaging line transients and EMI out of susceptible equipment.

They are also an ideal solution in situations where there is a

need to suppress line disturbances at the source.

With a working voltage of 440 VAC in line-to-line (Class X) and

300 VAC in line-to-ground (Class Y) applications, these safety

capacitors meet the impulse test criteria outlined in IEC Standard

60384. Meeting subclass X1 and Y2 requirements, these devices

are certiﬁed to withstand impulses up to 4 KV (X1) and 5 KV (Y2)

respectively. These encapsulated devices also meet the ﬂame test

requirements outlined in UL Standard 94V–0.

Safety Certiﬁed Capacitors are classiﬁed as either X and/or

Y capacitors. Class X capacitors are primarily used in line-to-

line (across-the-line) applications. In this application there is

no danger of electric shock to humans should the capacitor

fail, but could result in a risk of ﬁre. The class Y capacitor is

primarily used in line-to-ground (line by-pass) applications. In

this application, failure of the capacitor could lead to danger of

electric shock.

Ordering Information

C9

7

1

U

472

M

Z

W

D

A

7317

Ceramic

Series

Body

Diameter

Lead

Capacitance Capacitance

Code (pF) Tolerance

2 signiﬁcant C = ±0.25 pF Z = X1

digits + D = ±0.5 pF 440 VAC (NP0)

Number of J = ±5% / Y2 300 S = SL

Rated

Voltage Temp. Char.

Dielectric/

Lead

Failure

Packaging

(C-Spec)^2,3

Spec.

Design

Spacing^1,3

Conﬁg.^2,3Rate

C9 =

0 = 7.0 mm 7 = 7.5 mm

U =

N = CH

D =

A =

A = 7317 = Ammo Pack

N/A WL30 = Bulk/3.0 mm

Lead length

Ceramic 1 = 8.0 mm 1 = 10.0 mm Safety

900

Series

Disc Straight

B = Vertical

2 = 9.0 mm

3 = 10.0 mm

4 = 11.0 mm

6 = 13.0 mm

8 = 15.0 mm

zeroes

Use 9 for

1.0 -

K = ±10%

M = ±20%

VAC

Y = Y5P

W = Y5U

V = Y5V

Kink

C =

Outside

Kink

WL35 = Bulk/3.5 mm

Lead length

WL40 = Bulk/4.0 mm

Lead length

9.9 pF

e.g., 2.2 pF

= 229

D = Inside

Kink

WL45 = Bulk/4.5 mm

Lead length

WL50 = Bulk/5.0 mm

Lead length

WL20 = Bulk/20 mm

Lead length

¹Capacitor body diameter will limit available lead spacing and packaging options. See "Dimensions" and "Product Ordering Codes and Ratings" sections of this

document to determine availability.

²"Vertical Kink","Outside Kink" and "Inside Kink" lead conﬁgurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead length is

only available on capacitors with straight leads (lead conﬁguration ordering code "A"). For nonstandard lead length inquiries, please contact KEMET.

³Bulk packaging lead length availability is dependent upon "Lead Conﬁguration" and "Lead Spacing." See "Dimensions" section of this document to verify

availability of a speciﬁc lead length option. For nonstandard lead length inquiries, please contact KEMET.

One world. One KEMET

1

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Lead Conﬁgurations

Straight

Vertical Kink

Outside Kink

Inside Kink

Dimensions – Millimeters

Lead

Conﬁg.

Ordering

Code¹

Packaging

C-Spec

F

L

D

T

e

Ød

Lead

Spacing

Tolerance

Lead

Conﬁg.

Packaging

Type²

Lead

Length

Body

Lead

Ordering

Spacing²

Diameter²Thickness Meniscus Dia.

Code³

7317

Ammo Pack 20.0 +1.5/-1.0

3.0 ±1.0

WL30

WL45

WL50

7317

7.5

±1.0

Bulk

4.5 ±1.0

5.0 ±1.0

See Table 1 - "Product

Ordering Codes and

3.0

maximum

Straight

A

0.5 ±0.1

Ammo Pack 20.0 +1.5/-1.0

3.0 ±1.0

Ratings"

WL30

WL45

WL50

7317

10.0

Bulk

4.5 ±1.0

5.0 ±1.0

Ammo Pack 18.0 +2.0/-0

7.5

±1.0

3.5 ±1.0

WL35

WL40

7317

Bulk

See Table 1 - "Product

Ordering Codes and

Ratings"

4.0 ±1.0

Vertical Kink

(Preformed)

3.0

maximum

B

0.5 ±0.1

Ammo Pack 18.0 +2.0/-0

10.0

3.5 ±1.0

WL35

WL40

Bulk

4.0 ±1.0

¹Lead Conﬁguration is identiﬁed in the 13^thcharacter of the ordering code. See "Lead Conﬁguration" and "Ordering Information" sections of this document for

further details.

²Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for

further details.

³The "Packaging C-Spec" is a 4-digit numeric or alphanumeric code which identiﬁes both the packaging type and lead length requirement. When ordering, this

code must be included in the 15^ththrough 18^thcharacter positions of the ordering code. See "Ordering Information" section of this document for further details.

2

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Dimensions – Millimeters cont'd

Lead

Conﬁg.

Ordering

Code¹

Packaging

C-Spec

F

L

D

T

e

Ød

Lead

Spacing

Tolerance

Lead

Conﬁg.

Packaging

Type²

Lead

Length

Body

Lead

Ordering

Spacing²

Diameter²Thickness Meniscus Dia.

Code³

Ammo Pack 18.0 +2.0/-0

3.5 ±1.0

7317

WL35

WL40

WL50

7317

7.5

±1.0

Bulk

4.0 ±1.0

5.0 ±1.0

See Table 1 - "Product

Ordering Codes and

Outside Kink

(Preformed)

3.0

maximum

C

0.5 ±0.1

Ammo Pack 18.0 +2.0/-0

3.5 ±1.0

Ratings"

WL35

WL40

WL50

7317

10.0

Bulk

4.0 ±1.0

5.0 ±1.0

Ammo Pack 18.0 +2.0/-0

Bulk 3.5 ±1.0

Ammo Pack 18.0 +2.0/-0

Bulk 3.5 ±1.0

7.5

WL35

7317

Inside Kink

(Preformed)

13.0

maximum

7.0

maximum

3.0

maximum

D

0.5 ±0.1

10.0

WL35

¹Lead Conﬁguration is identiﬁed in the 13^thcharacter of the ordering code. See "Lead Conﬁguration" and "Ordering Information" sections of this document for

further details.

²Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for

further details.

³The "Packaging C-Spec" is a 4-digit numeric or alphanumeric code which identiﬁes both the packaging type and lead length requirement. When ordering, this

code must be included in the 15^ththrough 18^thcharacter positions of the ordering code. See "Ordering Information" section of this document for further details.

3

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Beneﬁts

• Safety Standard Recognized (IEC 60384-14)

• Reliable operation up to 125°C

• Class X1/Y2

• 7.5 mm and 10 mm lead spacing

• Lead (Pb)-free and RoHS Compliant

• Halogen Free

• Capacitance offerings ranging from 2.0 pF up to 10,000 pF

• Available capacitance tolerances of ±0.25 pF, ±0.5 pF, ±5%, ±10%, and ±20%

• High reliability

• Preformed (crimped) or straight lead conﬁgurations

• Non-polar device, minimizing installation concerns

• Encapsulation meets ﬂammability standard UL 94V–0

Applications

Typical applications include:

• Line-to-line (Class X) ﬁltering

• Line-to-ground (Class Y) ﬁltering

• Antenna coupling

• Primary and secondary coupling (switching power supplies)

• Line disturbances suppression (motors and motor controls, relays, switching power supplies, and inverters)

Approval Standard and Certiﬁcation No.

Safety Standard

Standard No.

Subclass

Working Voltage

440 VAC

Certiﬁcate No.

VDE

(ENEC)

X1

Y2

IEC 60384–14

40036415

300 VAC

These devices are VDE/ENEC recognized for antenna coupling and AC line-to-line (Class X) and line-to-ground (Class Y) applications per IEC60384–14.

Environmental Compliance

These devices are Halogen Free and RoHS Compliant. They meet all requirements set forth by both EU and China RoHS directives.

4

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

General Speciﬁcations/Performance Characteristics

Dielectric/Temperature Characteristic:

CH(NP0)

SL

Y5P

Y5U

Y5V

Operating Temperature Range

-40°C to +125°C

-1,000 ~ +350

ppm/ºC

Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC)

Dielectric Withstanding Voltage (7.5 mm and 10 mm Lead Spacing)

±60 ppm/ºC

±10%

+20%/-55% ~ +30%/-80%

2,600 VAC

(60 ±5 seconds at 25ºC)

30 pF% and above: ≥ 1,000

Below 30 pF: ≥ 400 +(20 x C)*

Quality Factor (Q)

Dissipation Factor (tanδ) at +25ºC¹

See “Dissipation Factor”

See “Quality Factor”

2.50%

5.0%

10,000 MΩ Minimum

(500 VDC applied for 60 ±5 seconds @ 25°C)

Insulation Resistance (IR) Limit at +25°C

*C = Nominal capacitance

²Capacitance and Dissipation Factor (DF) measured under the following conditions:

CH(NP0) & SL: 1 MHz ± 100 kHz and 1.0 ±0.2 Vrms

X5P, Y5U and Y5V: 1 kHz ± 50 Hz and 1.0 ±0.2 Vrms

Note: When measuring capacitance, it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as

Automatic Level Control (ALC). The ALC feature should be switched to "ON."

5

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 1 – Product Ordering Codes and Ratings

Dimensions (mm)

Body

Diameter Thickness

(Maximum) (Maximum)

Lead Spacing

Bulk Ammo

Dielectric/

Temp.

Char.

KEMET

Part Number

Capacitance

Tolerance

Body

Capacitance

Lead

Diameter Packaging Packaging

C90(1)U209CZND(2)A(3)

C90(1)U309CZND(2)A(3)

C90(1)U409CZND(2)A(3)

C90(1)U509CZND(2)A(3)

C90(1)U609DZND(2)A(3)

C90(1)U709DZND(2)A(3)

C90(1)U809DZND(2)A(3)

C90(1)U909DZND(2)A(3)

C90(1)U100DZND(2)A(3)

C90(1)U120JZND(2)A(3)

C90(1)U150JZND(2)A(3)

C91(1)U180JZND(2)A(3)

C91(1)U200JZND(2)A(3)

C91(1)U220JZND(2)A(3)

C91(1)U240JZND(2)A(3)

C92(1)U270JZND(2)A(3)

C92(1)U300JZND(2)A(3)

C92(1)U330JZND(2)A(3)

C93(1)U360JZND(2)A(3)

C93(1)U390JZND(2)A(3)

C94(1)U470JZND(2)A(3)

2.0 pF

3.0 pF

4.0 pF

5.0 pF

6.0 pF

7.0 pF

8.0 pF

9.0 pF

10 pF

12 pF

15 pF

18 pF

20 pF

22 pF

24 pF

27 pF

30 pF

33 pF

36 pF

39 pF

47 pF

±0.25 pF

±0.5 pF

7.0

7.5 mm

or

10 mm

CH

(NP0)

5.0

0.5 ±0.1

8.0

±5%

9.0

10.0

11.0

C90(1)U100JZSD(2)A(3)

C90(1)U120JZSD(2)A(3)

C90(1)U150JZSD(2)A(3)

C90(1)U180JZSD(2)A(3)

C90(1)U200JZSD(2)A(3)

C90(1)U220JZSD(2)A(3)

C90(1)U240JZSD(2)A(3)

C90(1)U270JZSD(2)A(3)

C90(1)U300JZSD(2)A(3)

C90(1)U330JZSD(2)A(3)

C90(1)U360JZSD(2)A(3)

C90(1)U390JZSD(2)A(3)

C90(1)U470JZSD(2)A(3)

C90(1)U500JZSD(2)A(3)

C90(1)U510JZSD(2)A(3)

C91(1)U560JZSD(2)A(3)

C91(1)U620JZSD(2)A(3)

C91(1)U680JZSD(2)A(3)

C91(1)U750JZSD(2)A(3)

C92(1)U820JZSD(2)A(3)

C93(1)U101JZSD(2)A(3)

10 pF

12 pF

15 pF

18 pF

20 pF

22 pF

24 pF

27 pF

30 pF

33 pF

36 pF

39 pF

47 pF

50 pF

51 pF

56 pF

62 pF

68 pF

75 pF

82 pF

100 pF

7.0

7.5 mm

or

10 mm

SL

±5%

5.0

0.5 ±0.1

8.0

9.0

10.0

C9 _KEMET7_{Part Number}

1

U

472_Capacitance

M

_{Body Di}Z_{ameter B}W_{ody Thickness}

D

_LeadA_Diameter

A

7317

Capacitance

Lead Spacing

Tolerance

(Maximum)

Ceramic

Body

Lead

Capacitance Capacitance

Rated

Dielectric/

Lead

Failure

Packaging

(C-Spec)^2,3

Spec.

Design

Series

Diameter

Spacing^1,3

Code (pF)

Tolerance

Voltage Temp. Char.

C o n ﬁ g . ^2,3Rate

(1) To properly complete ordering code, insert the one-digit numeric code to reﬂect required lead spacing: (Note that select capacitance values and packaging

C9 =

0 = 7.0 mm 7 = 7.5 mm

U =

2 signiﬁcant C = ±0.25 pF Z = X1

N = CH

D =

Disc Straight

B = Vertical

Kink

A =

A = 7317 = Ammo Pack

N/A WL30 = Bulk/3.0 mm

Lead length

options may limit lead spacing availability. See table above to verify availability.)

Ceramic 1 = 8.0 mm 1 = 10.0 mm Safety digits + D = ±0.5 pF 440 VAC (NP0)

Number of J = ±5% / Y2 300 S = SL

zeroes K = ±10% VAC Y = Y5P

7 = 7.5 mm

900

2 = 9.0 mm

3 = 10.0 mm

4 = 11.0 mm

6 = 13.0 mm

1 = 10.0 mm

Series

WL35 = Bulk/3.5 mm

Lead length

WL40 = Bulk/4.0 mm

Lead length

WL45 = Bulk/4.5 mm

Lead length

(2) To properly complete ordering code, insert the one-digit character code to reﬂect the required lead conﬁguration: (See "Lead Conﬁguration" section of this

Use 9 for

1.0 -

M = ±20%

W = Y5U

V = Y5V

C =

Outside

Kink

D = Inside

Kink

document, page 2, for further details.)

8 = 15.0 mm

9.9 pF

e.g., 2.2 pF

= 229

A = Straight

B = Vertical Kink

C = Outside Kink

D = Inside Kink

WL50 = Bulk/5.0 mm

Lead length

WL20 = Bulk/20 mm

(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this

Lead length

document, page 2, for available options.

6

Roll Over for

Order Info.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 1 – Product Ordering Codes and Ratings cont'd

Dimensions (mm)

Body

Diameter Thickness

(Maximum) (Maximum)

Lead Spacing

Bulk Ammo

Dielectric/

Temp.

Char.

KEMET

Part Number

Capacitance

Tolerance

Body

Capacitance

Lead

Diameter Packaging Packaging

C90(1)U101KZYD(2)A(3)

C90(1)U151KZYD(2)A(3)

C90(1)U221KZYD(2)A(3)

C90(1)U331KZYD(2)A(3)

C90(1)U471KZYD(2)A(3)

C91(1)U561KZYD(2)A(3)

C91(1)U681KZYD(2)A(3)

C92(1)U821KZYD(2)A(3)

C92(1)U102KZYD(2)A(3)

100 pF

150 pF

220 pF

330 pF

470 pF

560 pF

680 pF

820 pF

1,000 pF

7.0

7.5 mm

or

10 mm

Y5P

±10%

5.0

0.5 ±0.1

8.0

9.0

C90(1)U102MZWD(2)A(3)

C92(1)U152MZWD(2)A(3)

C92(1)U222MZWD(2)A(3)

C94(1)U332MZWD(2)A(3)

C96(1)U392MZWD(2)A(3)

C96(1)U472MZWD(2)A(3)

1,000 pF

1,500 pF

2,200 pF

3,300 pF

3,900 pF

4,700 pF

7.0

9.0

7.5 mm or 10 mm

Y5U

±20%

5.0

0.5 ±0.1

7.5 mm or 10 mm

11.0

13.0

10 mm only

C90(1)U102MZVD(2)A(3)

C90(1)U152MZVD(2)A(3)

C90(1)U222MZVD(2)A(3)

C92(1)U332MZVD(2)A(3)

C94(1)U392MZVD(2)A(3)

C94(1)U472MZVD(2)A(3)

C96(1)U682MZVD(2)A(3)

C98(1)U103MZVD(2)A(3)

1,000 pF

1,500 pF

2,200 pF

3,300 pF

3,900 pF

4,700 pF

6,800 pF

10,000 pF

7.0

7.5 mm or 10 mm

9.0

Y5V

±20%

5.0

0.5 ±0.1

7.5 mm or 10 mm

11.0

13.0

15.0

10 mm only

Capacitance

Tolerance

Body Diameter

(Maximum)

Body Thickness

(Maximum)

KEMET Part Number

Capacitance

Lead Diameter

Lead Spacing

(1) To properly complete ordering code, insert the one-digit numeric code to reﬂect required lead spacing: (Note that select capacitance values and packaging

options may limit lead spacing availability. See table above to verify availability.)

7 = 7.5 mm

1 = 10.0 mm

(2) To properly complete ordering code, insert the one-digit character code to reﬂect the required lead conﬁguration: (See "Lead Conﬁguration" section of this

document, page 2, for further details.)

A = Straight

B = Vertical Kink

C = Outside Kink

D = Inside Kink

(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this

document, page 2, for available options.

C9

7

1

U

472

M

Z

W

D

A

7317

Ceramic

Series

Body

Diameter

Lead

Capacitance Capacitance

Code (pF) Tolerance

2 signiﬁcant C = ±0.25 pF Z = X1

digits + D = ±0.5 pF 440 VAC (NP0)

Number of J = ±5% / Y2 300 S = SL

Rated

Voltage Temp. Char.

Dielectric/

Lead

Failure

Packaging

(C-Spec)^2,3

Spec.

Design

Spacing^1,3

C o n ﬁ g . ^2,3Rate

C9 =

0 = 7.0 mm 7 = 7.5 mm

U =

N = CH

D =

A =

A = 7317 = Ammo Pack

N/A WL30 = Bulk/3.0 mm

Lead length

Ceramic 1 = 8.0 mm 1 = 10.0 mm Safety

900

Series

Disc Straight

B = Vertical

2 = 9.0 mm

3 = 10.0 mm

4 = 11.0 mm

6 = 13.0 mm

8 = 15.0 mm

zeroes

Use 9 for

1.0 -

K = ±10%

M = ±20%

VAC

Y = Y5P

W = Y5U

V = Y5V

Kink

C =

Outside

Kink

WL35 = Bulk/3.5 mm

Lead length

WL40 = Bulk/4.0 mm

Lead length

9.9 pF

e.g., 2.2 pF

= 229

D = Inside

Kink

WL45 = Bulk/4.5 mm

Lead length

WL50 = Bulk/5.0 mm

Lead length

WL20 = Bulk/20 mm

Lead length

7

Roll Over for

Order Info.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions

Item

Speciﬁcation

Test Method

-40ºC to +125ºC

Operating Temperature Range

Between lead

wires

The capacitor shall not be damaged when 2,600 VAC(rms) is applied

between the lead wires for 60 seconds.

No failures

The terminals (leads) of the capacitor shall

be connected together. A metal foil is tightly

wrapped around the body of the capacitor at a

distance of about 3 to 4 mm from each terminal.

The capacitor is then inserted into a container

ﬁlled with metal balls approximately 1 mm in

diameter. 2,600 VAC(rms) is applied for 60

seconds between the capacitor lead wires and

metal balls.

Dielectric

Strength

Body Insulation

No failures

The insulation resistance shall be measured with 500 ±50 VDC applied

after 60 ±5 seconds of charging.

Insulation Resistance (IR)

Capacitance

10,000 MΩ minimum

Within speciﬁed tolerance

Temperature

Speciﬁcation

Characteristics

Y5P, Y5U

Y5V

Y5P, Y5U and Y5V: Capacitance is measured at 1 kHz ±20% and 5

Vrms or less. (20 ±2°C)

DF ≤ 2.5%

DF ≤ 5.0%

NP0 and SL: Capacitance is measured at 1 MHz ±20% and 1.0 ±0.2

Vrms (25°C)

Dissipation Factor (DF) or Q

NP0,SL

≥ 30 pF: Q ≥ 1000

< 30 pF: Q ≥ 400

+(20 x C)

C = Nominal

capacitance

A capacitance measurement is made at each step speciﬁed:

Temperature

Characteristics

Capacitance

Change

Step

Temperature

+20 ±2ºC

1

Y5P

Y5U

Y5V

CH

Within ±10%

Within +20%/-55%

Within ~+30%/-80%

0 ±60 ppm/ºC

2

-25 ±2ºC

Temperature Characteristics

3

+20 ±2ºC

4

+85 ±2ºC

+20 ±2ºC

5

SL

-1,000 ~+350 ppmºC

(+20ºC ~+85ºC)

Pre-treatment:

Capacitor is stored at 85 ±2ºC for 1 hour and then placed at room

condition¹for 24 ±2 hours before measurement.

With the termination in its normal position, the specimen is held by its

body in such a manner that the axis of the termination is vertical; a

tensile force of 10 N is applied to the termination in the direction of its

axis and acting in a direction away from the body of the specimen.

With the termination in its normal position, the specimen is held by its

body in such a manner that the axis of the termination is vertical; a

mass force of 5 N is then suspended from the end of the termination.

The body of the specimen is then inclined within a period of 2 to 3

seconds, through an angle of approximately 90° in the vertical plane

and then resumed to its initial position over the same period of time;

this operation constitutes one bend. One bend immediately followed by

a second bend in the opposite direction.

Tensile

Lead wire or capacitor body shall not break.

Terminal Strength

Bending

The lead wire of the capacitor is dipped into molten solder for 2 ±0.5

seconds. The depth of immersion is up to 1.5 mm (+5/-0 mm) from the

root of lead wires.

Lead wire should have a uniform coating of

solder in the axial direction and over 3/4 of its

circumference.

Solderability

Solder Temperature: Lead free solder (Sn-3Ag – 0.5Cu) 245°C ±5°C.

¹“Room Condition” is deﬁned as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

8

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item

Speciﬁcation

Test Method

As shown in the ﬁgure below, the lead wires are immersed in molten

solder up to 1.5 mm (+5/-0 mm) from the end of the epoxy meniscus

(root of lead wire).

Duration/Solder Temperature: 3.5 ±0.5 seconds/350°C ±10°C or 10 ±1

seconds/260°C ±5°C

No visual defect

Appearance

IR

1,000 MΩ

Dielectric

Strength

Per item 1

Soldering Effect

(Non-Preheat)

Y5P, Y5U and Y5V: Within ±10%

SL, CH (NP0): Within ±2.5% or ±0.25 pF,

whichever is larger.

Capacitance

Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then

placed at room condition¹for 24 ±2 hours before initial measurements.

Post-treatment: Capacitor is stored for 1 to 2 hours at room

condition¹.

Appearance

IR

No visual defect

1,000 MΩ

Capacitor is stored at 120°C +0/-5°C for 60 +0/-5 seconds. Then, as

shown in the ﬁgure below, the lead wires are immersed in molten solder

up to 1.5 mm (+5/-0mm) from the end of the epoxy meniscus (root of

lead wire).

Dielectric

Strength

Duration/Solder Temperature: 7.5 +0/-1 seconds/260°C ±5°C

Per item 1

Soldering Effect

(Preheat)

Y5P, Y5U and Y5V: Within ±10%

SL, CH (NP0): Within ±2.5% or ±0.25 pF,

whichever is larger.

Capacitance

Appearance

Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then

placed at room condition¹for 24 ±2 hours before initial measurements.

Post-treatment: Capacitor is stored for 1 to 2 hours at room condition¹.

No visual defect

Steady State Humidity:

Load Humidity:

Temperature

Characteristics

Capacitance

Change

Y5P

Y5U

Within ±10%

Within ±20%

Within ±30%

Capacitance

Y5V

90 to 95% humidity at 40°C

±2°C for 500 ±12 hours with full

rated voltage applied.

SL CH (NP0)

Within ±2.5% or

±0.25 pF, whichever

is larger.

90 to 95% humidity at 40°C

±2°C for 500 ±12 hours.

Biased Humidity

Post Treatment:

Capacitor is stored for 1 to 2

Y5P and Y5U: 5.0% maximum

Capacitor is stored for 1 to 2

DF

Q

hours at room condition¹.

Y5V: 7.5% maximum

SL and CH(NP0): Less than 30 pF:

Q ≥ 100 + 10 × C/3

More than 30 pF: Q ≥ 200

C = Nominal capacitance

Y5P, Y5V and Y5U: 3,000 MΩ minimum

SL and CH (NP0): 1,000 MΩ minimum

IR

Dielectric

Strength

No failures

¹“Room Condition” is deﬁned as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

9

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item

Speciﬁcation

Test Method

Impulse Voltage: Each individual capacitor is subjected to three 5 kv

impulses prior to life testing.

No visual defect

Appearance

Y5P, Y5V and Y5U: Within ±20%

SL and CH (NP0): Within ±3 or ±0.3 pF,

whichever is larger.

3,000 MΩ minimum

SL and CH (NPO): 1,000 MΩ minimum

Capacitance

Change

Cx tr td

U

PR

Vp

(uF) (uS) (uS)

0.9Vp

U

PP

0.01 1.2 46

0.1 1.5 47

IR

0.5Vp

High Temperature

Life

tr

Dielectric

Strength

td

No failures

Time

Capacitors are placed in a circulating air oven for a period of 1,000

hours. The air in the oven is maintained at a temperature of 125°C ±2

throughout the test. The capacitors are subjected to AC 510 Vrms.

Each hour the voltage is increased to 1,000 Vrms for 0.1 seconds.

The capacitor is exposed to a ﬂame for 15 seconds and then removed

for 15 seconds. This test is repeated for 5 cycles.

The capacitor ﬂame extinguishes as follows:

Cycle

1 ~ 4

5

Time

Flame Test

30 seconds maximum

60 seconds maximum

The capacitors are individually wrapped in at least one, but not more

than two, complete layers of cheesecloth. They are then subjected

to 20 discharges. The interval between successive discharges is 5

seconds. The VAC is maintained for 2 minutes after the last discharge.

C_{1, 2}

1 μF ±10%

C₃

Cx

V_AC

V_R

Vt

0.033 μF ±5% 10 kV

Test capacitor

Active Flammability

The cheesecloth should not ignite.

L_1-41.5 Mh ±20% 16A Rod core choke

R

Ct

F

100 ±2%

VR ±5%

3 μF ±5% 10 kV

Fuse, Rated 10A

Rated Voltage

Voltage applied to Ct

¹“Room Condition” is deﬁned as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item

Speciﬁcation

Test Method

The capacitor under test is held into a ﬂame and in a position which

best promotes burning. Each specimen is exposed to the ﬂame one

time.

The burning time should not exceed 30

seconds.

Passive Flammability

The tissue paper should not ignite.

Time of exposure to ﬂame:

Length of ﬂame:

30 seconds

12 ±1 mm

Gas burner length:

Inside diameter:

Outside diameter:

35 mm minimum

0.5 ±0.1 mm

0.9 mm maximum

95% minimum

Gas butane gas purity:

Appearance

No visual defect

Temperature

Characteristics

Capacitance

Change

The capacitor is subjected to 5 temperature cycles.

SL, CH (NP0)

Y5P

Within ±5%

Within ±10%

Within ±20%

Capacitance

(Temperature Cycle)

Time

Step Temperature (°C)

Y5U, Y5V

(minutes)

1

2

3

4

-40 +0/-3

Room temperature

125 +3/-0

30

3

SL, CH (NP0)

≥ 30 pF: Q ≥ 350

< 30 pF: Q ≥ 275

+5/2C

C = Nominal

capacitance

Temperature

Cycle

30

3

Room temperature

DF/Q

Y5P

DF ≤ 5%

Pre-treatment: Capacitor shall be stored at 85 ±2 for 1 hour then

placed at room condition¹for 24 ±2 hours.

Y5U, Y5V

DF ≤ 7.5%

Post-treatment: Capacitor is stored for 1 to 2 hours at room condition¹.

IR

3,000 MΩ minimum

No failures

Dielectric

Strength

¹“Room Condition” is deﬁned as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Soldering and Mounting Information

Soldering:

When soldering this product to a PCB/PWB, do not exceed the solder heat resistance speciﬁcation of the capacitor. Subjecting this

product to excessive heating could reﬂow the solder joint between the lead and ceramic element and/or may result in thermal shocks

that can crack the ceramic element.

When soldering these capacitors with a soldering iron, it should be performed under the following conditions:

• Temperature of iron-tip: 400ºC maximum

• Soldering iron wattage: 50 W maximum

• Soldering time: 3.5 seconds maximum

Cleaning (ultrasonic cleaning):

To perform ultrasonic cleaning, observe the following conditions:

• Rinse bath capacity: Output of 20 watts per liter or less

• Rinsing time: 5 minute maximum

• Do not vibrate the PCB/PWB directly

• Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires

Construction

Reference

Item

Encapsulation¹

Dielectric Material

Solder

Material

Epoxy resin, Pigment (Blue/UL 94 V–0)

BaTiO₃

1

2

3

4

Sn 96.5, Ag 3, Cu 0.5

Electrodes

Ag (Glass frit)

Tinned copper clad steel wire

(Sn Plating 100% 3-7 µm)

5

Lead Wires

¹The minimum thickness of the insulation coating (encapsulation) is 0.4 mm

Note: Image is exaggerated in order to clearly identify all components of construction.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Capacitor Marking

These capacitors shall be stamped or laser marked with KEMET's trademark, type designation, capacitor class, rated voltage, rated

capacitance, and capacitance tolerance codes. In addition, all devices are marked with the recognized approval mark and a date/lot

code for traceability. Marking will be supplied either on one side or both sides of the encapsulated capacitor body. All marking shall

be legible to allow for clear identiﬁcation of the component. Marking appears in legible contrast. Illustrated below is an example of the

marking format and content. (Two sided marking is limited to capacitors with body diameters ≤ 8.0 mm.)

AC472M

X1:440V~ Y2:300V~

2C12345

Location #

Description

Detail

KEMET Trademark

❶

Type Designation

(2 characters)

AC

❷

❸

❹

❺

❻

First two digits are the signiﬁcant ﬁgures of capacitance. Third digit indicates the additional

number of zeros. For example, 4,700 pF is identiﬁed as 472. (For values below 10 pF an “R” is

used in place of the decimal point, e.g., 2R0 = 2.0 pF.)

Rated Capacitance

(3 numeric characters)

Capacitance Tolerance

Code (1 character)

C = 0.25 pF, D = 0.5 pF, J = ±5%, K = ±10%, M = ±20%

VDE & ENEC approval mark

IEC 60384–14 3rd (2005)

Capacitor Class and Rated

Voltage

X1: 440 V ~ Y2: 300 V ~

Date/Lot Code, e.g., 3C12345

3

C

1

2345

Last digit of year,

Manufacturing

Location Code

Manufacturing Month:

Last 4 digits of

e.g.,

lot no.

Date/Lot Code

❼

1-9 = Jan - Sept

A = October

3 = 2013

N = November

D = December

Packaging Quantities

Carrier Tape Quantity

(15 mm Pitch¹)

Packaging Type

Loose (Bulk Bag)

(12.7 mm Pitch¹)

(25.4 mm Pitch¹)

Ammo Pack

Bulk

N/A

1,000 pieces/box

500 pieces/box

500 pieces/bag

N/A

¹For details regarding component pitch on carrier tape, see "Ammo Pack Taping Format" and "Ammo Pack Taping Speciﬁcations" sections of this document.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Figure 1 - Ammo Pack Taping Format

5 mm and 7.5 mm Lead Spacing:

10 mm Lead Spacing:

Table 3 – Ammo Pack Taping Speciﬁcations

Lead Spacing

5 mm

Straight

Preformed¹

7.5 mm

Straight

Preformed¹

10 mm

Straight

Preformed¹

Lead Style

Item

Symbol

Dimensions (mm)

Lead Spacing

Component Pitch

Sprocket Hole Pitch

F

P

5.0 +0.8/-0.2

12.7

7.5 ±1.0

10.0 ±1.0

25.4 ±2

15.0

P₀

12.7 ±0.3

15.0 ±0.3

12.7 ±0.3

Sprocket Hole Center to

P₂

6.35 ±1.5

7.5 ±1.5

12.7 ±1.5

Component Center

Sprocket Hole Center to Lead Center

Body Diameter

P₁

D

3.75 ±1.0

7.7 ±1.5

See "Product Ordering Codes and Ratings" section of this document.

Component Alignment (side/side)

Carrier Tape Width

∆S

W

0 ±2.0

18.0 +1.0/-0.5

9.0 ±0.5

Sprocket Hole Position

W₁

¹Prefromed (crimped) lead conﬁgurations include vertical kink, outside kink and inside kink. See "Lead Conﬁgurations" and "Ordering Information" sections of this

document for further details.

²Also referred to as "lead length" in this document.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 3 – Ammo Pack Taping Speciﬁcations cont'd

Lead Spacing

5 mm

Preformed¹

7.5 mm

Straight

Preformed¹

10 mm

Lead Style

Straight

Preformed¹

Item

Symbol

H₀

Dimensions (mm)

Height to Seating Plane²

N/A

18.0 +2.0/-0

N/A

20.0 +1.5/-1.0

18.0 +2.0/-0

N/A

18.0 +2.0/-0

N/A

(preformed leads¹)

Height to Seating Plane²

H

20.0 +1.5/-1.0

(straight leads)

Lead Protrusion

Diameter of Sprocket Hole

Lead Diameter

ℓ

2.0 maximum

D₀

φd

t₁

4.0 ±0.2

0.5 ±0.1

0.6 ±0.3

Carrier Tape Thickness

Total Thickness (Carrier Tape,

Hold-Down Tape and Lead)

t₂

1.5 maximum

∆h₁

∆h₂

L

Component Alignment (front/back )

2.0 maximum

11.0 maximum

Cut Out Length

Hold-Down Tape Width

Hold-Down Tape Position

W₀

W₂

11.0 minimum

3.0 maximum

11.5 minimum

1.5 ±1.5

¹Prefromed (crimped) lead conﬁgurations include vertical kink, outside kink and inside kink. See "Lead Conﬁgurations" and "Ordering Information" sections of this

document for further details.

²Also referred to as "lead length" in this document.

Application Notes:

Storage and Operating Conditions:

The insulating coating of these devices does not form an air and moisture-tight seal. Avoid exposure to moisture and do not use or

store these devices in a corrosive atmosphere, especially where chloride gas, sulﬁde gas, acid, alkali, salt, or the like are present.

Before cleaning, bonding or molding these devices, it is important to verify that your process does not affect product quality and

performance. KEMET recommends testing and evaluating the performance of a cleaned, bonded or molded product prior to

implementing and/or qualifying any of these processes. Store the capacitors where the temperature and relative humidity do not

exceed 40 degrees Centigrade and 70% respectively. For optimum solderability, capacitor stock should be used promptly, preferably

within 6 months of receipt.

Working Voltage:

Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated for a

transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a capacitor with a

voltage rating greater than or equal to these irregular voltages.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Operating Temperature and Self-Generating Heat:

The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be sure to take

into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or similar

current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated heating should not exceed 20°C (while

operated at an atmosphere temperature of 25°C).

Handling - Vibration and Impact:

Do not expose these devices or their leads to excessive shock or vibration during use.

FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR

PARTIAL DISPERSION WHEN THE PRODUCT IS USED.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

KEMET Corporation

World Headquarters

Europe

Asia

Southern Europe

Paris, France

Tel: 33-1-4646-1006

Northeast Asia

Hong Kong

Tel: 852-2305-1168

2835 KEMET Way

Simpsonville, SC 29681

Sasso Marconi, Italy

Tel: 39-051-939111

Shenzhen, China

Tel: 86-755-2518-1306

Mailing Address:

P.O. Box 5928

Greenville, SC 29606

Beijing, China

Central Europe

Landsberg, Germany

Tel: 49-8191-3350800

Tel: 86-10-5829-1711

www.kemet.com

Tel: 864-963-6300

Fax: 864-963-6521

Shanghai, China

Tel: 86-21-6447-0707

Kamen, Germany

Tel: 49-2307-438110

Corporate Ofﬁces

Fort Lauderdale, FL

Tel: 954-766-2800

Taipei, Taiwan

Tel: 886-2-27528585

Northern Europe

Bishop’s Stortford, United Kingdom

Tel: 44-1279-460122

North America

Southeast Asia

Singapore

Southeast

Tel: 65-6586-1900

Lake Mary, FL

Tel: 407-855-8886

Espoo, Finland

Tel: 358-9-5406-5000

Penang, Malaysia

Tel: 60-4-6430200

Northeast

Wilmington, MA

Tel: 978-658-1663

Bangalore, India

Tel: 91-806-53-76817

Central

Novi, MI

Tel: 248-994-1030

West

Milpitas, CA

Tel: 408-433-9950

Mexico

Guadalajara, Jalisco

Tel: 52-33-3123-2141

Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not

assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of

KEMET Electronics Corporation.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Other KEMET Resources

Tools

Resource

Location

Conﬁgure A Part: CapEdge

SPICE & FIT Software

http://capacitoredge.kemet.com

http://www.kemet.com/spice

http://www.kemet.com/keask

http://www.kemet.com:8080/elc

Search Our FAQs: KnowledgeEdge

Electrolytic LifeCalculator

Product Information

Resource

Location

Products

Technical Resources (Including Soldering Techniques)

RoHS Statement

http://www.kemet.com/products

http://www.kemet.com/technicalpapers

http://www.kemet.com/rohs

Quality Documents

http://www.kemet.com/qualitydocuments

Product Request

Resource

Location

http://www.kemet.com/sample

http://www.kemet.com/kits

Sample Request

Engineering Kit Request

Contact

Location

Website

Contact Us

Investor Relations

Call Us

www.kemet.com

http://www.kemet.com/contact

http://www.kemet.com/ir

1-877-MyKEMET

Twitter

http://twitter.com/kemetcapacitors

Disclaimer

All product speciﬁcations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and

verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.

All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.

Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are

not intended to constitute – and KEMET speciﬁcally disclaims – any warranty concerning suitability for a speciﬁc customer application or use. The Information is intended for use only

by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise

provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.

Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still

occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective

circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.

Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not

be required.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)


型号：	C921U332MZVDBA7317
厂家：	KEMET CORPORATION
描述：	Ceramic Capacitor, Multilayer, Ceramic, 20% +Tol, 20% -Tol, Y5V, -80/+30% TC, 0.0033uF, Through Hole Mount, 3520, RADIAL LEADED 电容器
文件：	总19页 (文件大小：789K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

C921U332MZVDBA7317 [KEMET]

相关型号：

C921U472JZSDAA7317

C921U472JZSDBA7317

C921U472JZSDCA7317

C921U472JZSDDA7317

C921U472JZVDAA7317

C921U472JZVDBA7317

C921U472JZVDCA7317

C921U472JZVDDA7317

C921U472JZWDAA7317

C921U472JZWDBA7317

C921U472JZWDCA7317

C921U472JZWDDA7317