C961U222MWDCA7317 [KEMET]
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade);型号: | C961U222MWDCA7317 |
厂家: | KEMET CORPORATION |
描述: | Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade) |
文件: | 总15页 (文件大小:1916K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated,
AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Overview
KEMET’s 900 series encapsulated radial leaded ceramic
disc capacitors are specifically designed for interference-
suppression AC line filtering applications. Having
internationally recognized safety certifications, these
capacitors are well-suited for applications that require
keeping potentially disruptive or damaging line transients
and EMI out of susceptible equipment. They are also an
ideal solution when needing to suppress line disturbances
at the source.
With a working voltage of 760 VAC in line-to-line (Class X)and
500 VAC in line-to-ground (Class Y) applications, these safety
capacitors meet the impulse test criteria outlined in IEC
Standard 60384. Meeting subclass X1 and Y1 requirements,
these devices are certified to withstand impulses up to 4
KV (X1) and 8 KV (Y1) respectively. These encapsulated
devices also meet the flame test requirements outlined in UL
Standard 94V–0.
Safety Certified Capacitors are classified as either X and/
or Y capacitors. Class X capacitors are primarily used in
line-to line (across-the-line) applications. In this application
there is no danger of electric shock to humans should the
capacitor fail, but could result in a risk of fire. The class Y
capacitor is primarily used in line-to-ground (line by-pass)
applications. In this application, failure of the capacitor
could lead to danger of electric shock.
Click image above for interactive 3D content
Open PDF in Adobe Reader for full functionality
Ordering Information
C9
6
1
U
222
M
W
W
D
A
A
7317
Ceramic
Series
Body
Diameter
Lead
Spacing1
Capacitance Capacitance Rated Dielectric/
Lead
Config.1
Failure Packaging
Spec.
Design
Code (pF)
Tolerance
Voltage Temp. Char.
Rate
(C-Spec)
C9 =
1 = 8.0 mm
1 =
10.0 mm
U =
Two
K = ±10%
M = ±20%
W = X1
760 VAC
/Y1 500
VAC
W = Y5U
D = A = Straight
Disc B = Vertical
Kink
A =
N/A
See
"Packaging
C-Spec
Ordering
Options
Table"
Ceramic 2 = 9.0 mm
900 3 = 10.0 mm
Series 5 = 12.0 mm
6 = 13.0 mm
Safety significant
digits and
number of
zeroes
C = Outside
Kink
7 = 14.0 mm
8 = 15.0 mm
below
1 "Vertical Kink" and "Outside Kink" lead configurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead length is
only available on capacitors ordered with straight leads (lead configuration ordering code "A"). For nonstandard lead length inquiries, please contact
KEMET.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017
1
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Packaging C-Spec Ordering Options Table
Lead Length
(mm)2,3
Packaging
Ordering Code (C-Spec)
Packaging Type
20.0+1.5/−1.0 (straight leads)
18.0+2.0/−0 (preformed leads1)
Ammo Pack
7317
3.0±1.0
3.5±1.0
WL30
WL35
WL40
WL45
WL50
WL20
4.0±1.0
Bulk Bag
4.5±1.0
5.0±1.0
20.0 minimum4
1 Preformed (crimped) lead configurations include vertical kink, outside kink and inside kink. See "Lead Configurations" and "Ordering Information"
sections of this document for further details.
2 "Vertical Kink", "Outside Kink" and "Inside Kink" lead configurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead
length is only available on capacitors with straight leads (lead configuration ordering code "A"). For nonstandard lead length inquiries, please contact
KEMET.
3 For nonstandard lead length inquiries, please contact KEMET.
4 Lead length of 20.0 mm minimum only available for straight leads.
Benefits
• Safety Standard Recognized (IEC 60384–14)
• Reliable operation up to 125°C
• Class X1/Y1
• 10 mm lead spacing
• Lead (Pb)-free and RoHS Compliant
• Halogen free
• Available capacitance tolerances of ±5%, ±10% and ±20%
• High reliability
• Preformed (crimped) or straight lead configurations
• Non-polar device, minimizing installation concerns
• 100% pure matte tin-plated lead finish allowing for excellent solderability
• Encapsulation meets flammability standard UL 94V–0
Applications
Typical applications include:
• Line-to-line (Class X) filtering
• Line-to-ground (Class Y) filtering
• Antenna coupling
• Primary and secondary coupling (switching power supplies)
• Line disturbances suppression (motors and motor controls, relays, switching power supplies, and inverters)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017
2
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Lead Configurations
Straight
Vertical Kink
Outside Kink
D
T
D
T
D
T
ꢁꢂ0
ꢃaꢄimum
ꢅꢂ0
ꢃaꢄimum
ꢄꢁ0
ꢂaꢃimum
5ꢁ0 ꢂaꢃimum
ꢁꢂ0 ꢃaꢄimum
LL
LL
LL
ꢀ
ꢀ
ꢀ
S
S
S
Dimensions – Millimeters
S
D
T
e
ØF
Lead
Lead
Lead
Spacing
Tolerance
Configuration
Configuration
Ordering Code1
Lead
Body
Diameter2
Body
Thickness
Lead
Meniscus
Lead
Diameter
Spacing2
Straight
A
B
C
10.0
±1.0
±1.0
±1.0
See Table 1 -
"Product Ordering Codes
and Ratings"
Vertical Kink
(Preformed)
3.0
maximum
10.0
10.0
0.55±0.1
Outside Kink
(Preformed)
1 Lead Configuration is identified in the 13th character of the ordering code. See "Lead Configuration" and "Ordering Information" sections of this
document for further details.
2 Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this
document for further details.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017
3
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Approval Standard and Certification No.
Safety Standard
Standard No.
Subclass
Working Voltage
760 VAC
Certificate No.
X1
Y1
X1
Y1
VDE
(ENEC)
IEC 60384–14
40034867
500 VAC
760 VAC
UL
CAN/CSA
UL 60384–14 and
E356389
E60384–14
500 VAC
These devices are VDE/ENEC and UL recognized for antenna coupling and AC line-to-line (Class X) and line-to-ground (Class Y) applications per
IEC60384–14 and UL 60384–14.
Environmental Compliance
These devices are Halogen free and RoHS Compliant. They meet all requirements set forth by both EU and China RoHS
directives.
General Specifications/Performance Characteristics
Dielectric/Temperature Characteristic
Y5P
Y5U
Operating Temperature Range:
−40°C to +125°C
Capacitance Change with Reference to
+25°C and 0 VDC Applied (TCC):
±10%
+20%/−55%
4,000 VAC
(60±5 seconds at 25ºC)
Dielectric Withstanding Voltage
Quality Factor (Q)
See “Dissipation Factor”
Dissipation Factor (tanδ) at +25ºC1
2.50%
2.50%
10,000 MΩ Minimum
(500 VDC applied for 60±5 seconds at 25°C)
Insulation Resistance (IR) Limit at +25°C
1 Capacitance and Dissipation Factor (DF) measured under the following conditions:
1 kHz ±50 Hz and 1.0 ±0.2 Vrms
Note: When measuring capacitance, it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known
as Automatic Level Control (ALC). The ALC feature should be switched to "ON."
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017
4
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Table 1 – Product Ordering Codes and Ratings
Dimensions (mm)
Lead Spacing
Dielectric/
Temp.
Char.
KEMET
Part Number
Capacitance
Tolerance
Body
Diameter
(Maximum) (Maximum)
Body
Thickness
Capacitance
Lead
Bulk
Ammo
Packaging
Diameter Packaging
C911U101KWYD(1)A(2)
C911U151KWYD(1)A(2)
C911U221KWYD(1)A(2)
C911U331KWYD(1)A(2)
C921U471KWYD(1)A(2)
C931U561KWYD(1)A(2)
C931U681KWYD(1)A(2)
C951U102KWYD(1)A(2)
C921U102MWWD(1)A(2)
C931U152MWWD(1)A(2)
C961U222MWWD(1)A(2)
C961U332MWWD(1)A(2)
C971U392MWWD(1)A(2)
C981U472MWWD(1)A(2)
100 pF
150 pF
8.0
8.0
8.0
8.0
9.0
220 pF
330 pF
Y5P
±10%
470 pF
560 pF
10.0
680 pF
10.0
7.0
0.55 ±0.05
10 mm
1,000 pF
1,000 pF
1,500 pF
2,200 pF
3,300 pF
3,900 pF
4,700 pF
12.0
9.0
10.0
13.0
13.0
14.0
15.0
Y5U
±20%
(1) To properly complete ordering code, insert the one-digit character code to reflect the required lead configuration: (See "Lead Configuration" section
of this document, page 2, for further details.)
A = Straight
B = Vertical Kink
C = Outside Kink
(2) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code". See "Dimensions" section of
this document, page 2, for available options.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017
5
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Table 2 – Performance & Reliability: Test Methods and Conditions
Item
Specification
Test Method
−40ºC to +125ºC
Operating Temperature Range
Between lead
wires
The capacitor shall not be damaged when 4,000 VAC(rms) is
applied between the lead wires for 60 seconds.
No failures
The terminals (leads) of the capacitor
shall be connected together. A metal foil
is tightly wrapped around the body of the
capacitor at a distance of about 3 to 4 mm
Dielectric
Strength
ꢀetal
ꢁoil
Body Insulation
No failures
from each terminal. The capacitor is then
aꢃout
ꢄ to ꢅ mm
inserted into a container filled with metal
balls approximately 1 mm in diameter. 4,000
VAC(rms) is applied for 60 seconds between
the capacitor lead wires and metal balls.
ꢀetal
ꢂalls
The insulation resistance shall be measured with 500±50 VDC
Insulation Resistance (IR)
Capacitance
10,000 MΩ minimum
Within specified tolerance
DF ≤ 2.5%
applied after 60±5 seconds of charging.
Capacitance is measured at 1 kHz ±20% and 5 Vrms or less
(20±2°C)
Dissipation Factor (DF) or Q
A capacitance measurement is made at each step specified:
Step
Temperature
+20±2ºC
1
2
−25±2ºC
Temperature
Capacitance
Characteristics
Change
3
+20±2ºC
Temperature Characteristics
4
+85±2ºC
+20±2ºC
Y5U
Within +22%/−56%
5
Pre-treatment:
Capacitor is stored at 85±2ºC for 1 hour and then placed at room
condition1 for 24±2 hours before measurement.
With the termination in its normal position, the specimen is held
by its body in such a manner that the axis of the termination is
vertical; a tensile force of 10 N is applied to the termination in the
direction of its axis and acting in a direction away from the body
of the specimen.
Lead wire or capacitor body shall not
break.
Tensile
With the termination in its normal position, the specimen is held
by its body in such a manner that the axis of the termination is
vertical; a mass force of 5 N is then suspended from the end of
the termination. The body of the specimen is then inclined within
a period of 2 to 3 seconds, through an angle of approximately 90°
in the vertical plane and then resumed to its initial position over
the same period of time; this operation constitutes one bend.
One bend immediately followed by a second bend in the opposite
direction.
Terminal
Strength
Lead wire or capacitor body shall not
break.
Bending
The lead wire of the capacitor is dipped into molten solder for
5±0.5 seconds. The depth of immersion is up to 1.5 mm
(+5/−0 mm) from the root of lead wires.
Solder Temperature: Lead free solder (Sn-3Ag – 0.5Cu)
245°C ±5°C.
Lead wire should have a uniform coating
of solder in the axial direction and over
3/4 of its circumference.
Solderability
1 “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017
6
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Table 2 – Performance & Reliability: Test Methods and Conditions cont'd
Item
Specification
Test Method
As shown in the figure below, the lead wires are immersed in
molten solder up to 1.5 mm (+5/−0 mm) from the end of the
epoxy meniscus (root of lead wire).
No visual defect
Appearance
IR
1,000 MΩ
Duration/Solder Temperature: 3.5±0.5 seconds/350°C ±10°C or
10±1 seconds/260°C ±5°C
Dielectric
Strength
Per item 1
Tꢃermal
Screen
Capacitor
Soldering Effect
(Non-Preheat)
1ꢁ5 to
ꢂꢁ0 mm
ꢀolten
Solder
Capacitance
Within ±10%
Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and
then placed at room condition1 for 24±2 hours before initial
measurements.
Post-treatment: Capacitor is stored for 1 to 2 hours at room
condition1.
Capacitor is stored at 120°C +0/−5°C for 60+0/−5 seconds. Then,
as shown in the figure below, the lead wires are immersed in
molten solder up to 1.5 mm (+5/−0mm) from the end of the epoxy
meniscus (root of lead wire).
Appearance
IR
No visual defect
1,000 MΩ
Dielectric
Strength
Duration/Solder Temperature: 7.5 +0/−1 seconds/260°C ±5°C
Per item 1
Tꢃermal
Screen
Capacitor
Soldering Effect
(Preheat)
1ꢁ5 to
ꢂꢁ0 mm
ꢀolten
Solder
Capacitance
Within ±10%
Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and
then placed at room condition1 for 24±2 hours before initial
measurements.
Post-treatment: Capacitor is stored for 1 to 2 hours at room
condition1.
Appearance
Capacitance
No visual defect
Steady State Humidity:
Load Humidity:
Temperature
Characteristics
Capacitance
Change
90 to 95% humidity at 40°C
±2°C for 500 ±12 hours with
full rated voltage applied.
90 to 95% humidity at 40°C
±2°C for 500 ±12 hours.
Y5U
Within ±30%
Biased Humidity
Post Treatment:
DF
5.0% maximum
Post Treatment:
Capacitor is stored for 1 to 2
Capacitor is stored for 1 to 2
hours at room condition1.
hours at room condition1.
IR
3,000 MΩ minimum
No failures
Dielectric
Strength
Impulse Voltage: Each individual capacitor is subjected to three 8
kv impulses prior to life testing.
Appearance
No visual defect
Within ±20%
Capacitance
Change
Cꢀ tr td
ꢀꢀR
Vp
(uꢀ) (uS) (uS)
0ꢀ01 1ꢀꢁ ꢀ6
0ꢀ1 1ꢀ5 ꢀ7
0ꢀ9Vp
ꢀꢀꢀ
IR
3,000 MΩ minimum
0ꢀ5Vp
High
Temperature
Life
tr
Dielectric
Strength
td
Time
No failures
Capacitors are placed in a circulating air oven for a period of
1,000 hours. The air in the oven is maintained at a temperature of
125°C ±2°C throughout the test. The capacitors are subjected to
AC 850 Vrms. Each hour the voltage is increased to 1,000 Vrms
for 0.1 seconds. .
1 “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017
7
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Table 2 – Performance & Reliability: Test Methods and Conditions cont'd
Item
Specification
Test Method
The capacitor is exposed to a flame for 15 seconds and then
The capacitor flame extinguishes as
follows:
removed for 15 seconds. This test is repeated for 5 cycles.
Capacitor
ꢀlame
Cycle
Time
76
Flame Test
30 seconds
maximum
ꢁꢂ
1 ~ 4
1ꢃ7
60 seconds
maximum
Gas ꢅurner
5
ꢃ0ꢄ
(ꢆnitꢇmm)
The capacitors are individually wrapped in at least one, but not
more than two, complete layers of cheesecloth. They are then
subjected to 20 discharges. The interval between successive
discharges is 5 seconds. The VAC is maintained for 2 minutes
after the last discharge.
ꢃ
L1
Lꢀ
R
S1
C1
Vac
Cꢀ
Lꢁ
Cꢁ CX
Lꢂ
Ct
Vt
Sꢀ
Tr
ꢄscilloscope
C1, 2
L1-4
R
1 μF ±10%
C3
0.033 μF ±5% 10 kV
Test capacitor
VR ±5%
1.5 Mh ±20% 16A Rod core choke
100±2%
Cx
VAC
VR
Active Flammability
The cheesecloth should not ignite.
Ct
F
3 μF ±5% 10 kV
Rated Voltage
Voltage applied to Ct
Fuse, Rated 10A
Vt
Vꢀ
5ꢁV
time
1 “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017
8
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Table 2 – Performance & Reliability: Test Methods and Conditions cont'd
Item
Specification
Test Method
The capacitor under test is held into a flame and in a position
which best promotes burning. Each specimen is exposed to the
flame one time.
Test Specimen
ꢀ00
ꢁ5mm
ꢄ5ꢅ
Tissue
The burning time should not exceed 30
seconds.
The tissue paper should not ignite.
Passive Flammability
Aꢂout 10mm
Tꢆicꢇ ꢈoard
Time of exposure to flame:
Length of flame:
30 seconds
12±1 mm
35 mm minimum
0.5±0.1 mm
Gas burner length:
Inside diameter:
Outside diameter:
Gas butane gas purity:
0.9 mm maximum
95% minimum
The capacitor is subjected to 5 temperature cycles.
Appearance
No visual defect
Temperature Cycle
Dwell
Transition
Time
Temperature
Characteristics
Capacitance
Change
Step Temperature (°C)
Time
Capacitance
(minutes) (minutes)
Y5V
Within ±20%
1
2
3
4
−40 +0/−3
Room temperature
125 +3/−0
30
Temperature
3
Cycle
3
DF/Q
DF ≤ 7.5%
30
Room temperature
3
IR
3,000 MΩ minimum
No failures
Pre-treatment: Capacitor shall be stored at 85±2 for 1 hour then
placed at room condition1 for 24±2 hours.
Post-treatment: Capacitor is stored for 1 to 2 hours at room
condition1.
Dielectric
Strength
1 “Room Condition” is defined as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017
9
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Soldering and Mounting Information
Soldering:
When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor.
Subjecting this product to excessive heating could reflow the solder joint between the lead and ceramic element and/or may
result in thermal shocks that can crack the ceramic element.
When soldering these capacitors with a soldering iron, it should be performed under the following conditions:
• Temperature of iron-tip: 400ºC maximum
• Soldering iron wattage: 50 W maximum
• Soldering time: 3.5 seconds maximum
Cleaning (ultrasonic cleaning):
To perform ultrasonic cleaning, observe the following conditions:
• Rinse bath capacity: Output of 20 watts per liter or less
• Rinsing time: 5 minute maximum
• Do not vibrate the PCB/PWB directly
• Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires
Construction
Detailed Cross Section
Epoxy Encapsulation
(0.4 mm Minimum Thickness,
Pigment = Blue/UL 94 V-0)
Lead Attach Solder
(Sn96.5/Ag3/Cu0.5)
Dielectric Material
(BaTiO3)
Electrode
(Ag – Glass Frit)
Electrode
(Ag – Glass Frit)
Lead Wire
Lead Attach Solder
(Sn96.5/Ag3/Cu0.5)
Core Metal
Steel
Cu
Dielectric
Material
(BaTiO3)
Barrier Layer
100% Sn
(3-7 µm)
Finish Layer
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017 10
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Marking
These capacitors shall be stamped or laser marked with KEMET's trademark, type designation, capacitor class, rated voltage,
rated capacitance and capacitance tolerance codes. In addition, all devices are marked with the recognized approval mark
and a date/lot code for traceability. Marking will be supplied either on one side or both sides of the encapsulated capacitor
body. All marking shall be legible to allow for clear identification of the component. Marking appears in legible contrast.
Illustrated below is an example of the marking format and content. (Two sided marking is limited to capacitors with body
diameters ≤ 8.0 mm.)
Single Sided
Rated Capacitance
(3 Numeric Characters)
KEMET ID
Type Designation
(2 Characters)
Capacitance Tolerance Code
(1 Character)
VDE & ENEC
approval marks
IEC 60384-14 3rd
(2005)
Capacitor Class
and Rated Voltage
UL approval mark
Date/Lot Code
(See Table Below)
Double Sided
Front
Back
UL approval mark
Rated Capacitance
(3 Numeric Characters)
KEMET ID
Capacitance
Tolerance Code
(1 Character)
Type Designation
(2 Characters)
VDE & ENEC
approval marks
IEC 60384-14 3rd
(2005)
Capacitor Class
and Rated Voltage
Date/Lot Code
(See Table Below)
Date/Lot Code Explanation
6
C
6
1234
Manufacturing
Month:
Last digit of year,
e.g.,
Manufacturing
Location Code
Last 4 digits of
1-9 = Jan - Sept
A = October
N = November
D = December
lot no.
6 = 2016
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017 11
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Packaging Quantities
Ammo Pack (Carrier Tape)
Component pitch on carrier tape2
25.4 mm
Capacitor
Body Diameter (mm)
Bulk Bag
(Loose)
Body Diameter Code1
7.0
8.0
0
1
2
3
4
6
7
8
9.0
1,000 pieces/box
10.0
11.0
13.0
14.0
15.0
500 pieces/bag
500 pieces/box
1 The "Body Diameter Code" is located in the third character position of the ordering code. This code identifies the maximum diameter of the capacitor
body in millimeters. For more information regarding the ordering code, see "Ordering Information" section of this document.
2 For details regarding component pitch on carrier tape, see "Ammo Pack Taping Format" and "Ammo Pack Taping Specifications" sections of this
document.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017 12
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Figure 1 - Ammo Pack Taping Format (10 mm Lead Spacing)
∆ꢃ1 0 ∆ꢃꢄ
T maꢀimum
ꢁarꢂing Side
∆S
ꢀꢁ
ꢀ
D
e
ꢀ1
ꢃꢁ
ꢃ0
ꢂ
ꢅd
ꢄ0
L
ꢃ1
ꢃ
tꢄ
t1
ꢀ0
ꢅD0
ℓ
Table 3 – Ammo Pack Taping Specifications
Lead Spacing
Lead Style
10 mm
Straight
Preformed1
Item
Symbol
F
Dimensions (mm)
10.0±1.0
Lead Spacing
Component Pitch
Sprocket Hole Pitch
P
25.4±2
P0
P2
P1
D
12.7±0.3
12.7±1.5
Sprocket Hole Center to Component Center
Sprocket Hole Center to Lead Center
Body Diameter
7.7±1.5
See Table 1 - Product Ordering Codes and Ratings
Component Alignment (side/side )
Carrier Tape Width
∆S
W
0±2.0
18.0+1.0/−0.5
9.0±0.5
Sprocket Hole Position
W1
H0
H
Height to Seating Plane2 (preformed leads1)
Height to Seating Plane2 (straight leads)
Lead Protrusion
N/A
18.0+2.0/−0
20.0+1.5/−1.0
N/A
ℓ
2.0 maximum
4.0±0.2
Diameter of Sprocket Hole
Lead Diameter
D0
φd
t1
0.55±0.1
0.6±0.3
Carrier Tape Thickness
Total Thickness (Carrier Tape, Hold-Down Tape and
Lead)
t2
1.5 maximum
∆h1
∆h2
L
2.0 maximum
2.0 maximum
11.0 maximum
Component Alignment (front/back )
Cut Out Length
Hold-Down Tape Width
Hold-Down Tape Position
W0
W2
11.0 minimum
1.5±1.5
3.0 maximum for straight lead; not to exceed the bend for preformed1 lead
Coating Extension on Leads (meniscus)
Body Thickness
e
configurations.
7.0 Maximum
T
1 Preformed (crimped) lead configurations include vertical kink and outside kink. See "Lead Configurations" and "Ordering Information" sections of this
document for further details.
2 Also referred to as "lead length" in this document.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017 13
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
Application Notes:
Storage and Operating Conditions:
The insulating coating of these devices does not form an air and moisture-tight seal. Avoid exposure to moisture and do not
use or store these devices in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt, or the like
are present. Before cleaning, bonding or molding these devices, it is important to verify that your process does not affect
product quality and performance. KEMET recommends testing and evaluating the performance of a cleaned, bonded or
molded product prior to implementing and/or qualifying any of these processes. Store the capacitors where the temperature
and relative humidity do not exceed 40 degrees Centigrade and 70% respectively. For optimum solderability, capacitor stock
should be used promptly, preferably within 6 months of receipt.
Working Voltage:
Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated
for a transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a
capacitor with a voltage rating greater than or equal to these irregular voltages.
Operating Temperature and Self-Generating Heat:
The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be
sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current,
pulse current or similar current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated
heating should not exceed 20°C (while operated at an atmosphere temperature of 25°C).
Handling - Vibration and Impact:
Do not expose these devices or their leads to excessive shock or vibration during use.
FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR
PARTIAL DISPERSION WHEN THE PRODUCT IS USED.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017 14
Radial Leaded Ceramic Disc Capacitors
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
KEMET Electronic Corporation Sales Offices
For a complete list of our global sales offices, please visit www.kemet.com/sales.
Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for
checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such
applications, but are not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use.
The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any
technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no
obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component
failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards
(such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or
property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other
measures may not be required.
KEMET is a registered trademark of KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com
C1066_X1_760 VAC_Y1_500 VAC • 1/13/2017 15
相关型号:
C961U222MWWDAA7317
Safety Standard Recognized, 900 Series, Encapsulated, AS Type, X1 760 VAC/Y1 500 VAC (Industrial Grade)
KEMET
C961U222MWWDBA7317
Ceramic Capacitor, Ceramic, 20% +Tol, 20% -Tol, Y5U, -56/+22% TC, 0.0022uF, Through Hole Mount, 5128, RADIAL LEADED, HALOGEN FREE AND ROHS COMPLIANT
KEMET
C961U472JZSDAA7317
Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)
KEMET
C961U472JZSDBA7317
Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)
KEMET
C961U472JZSDCA7317
Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)
KEMET
C961U472JZSDDA7317
Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)
KEMET
C961U472JZVDAA7317
Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)
KEMET
C961U472JZVDBA7317
Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)
KEMET
C961U472JZVDCA7317
Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)
KEMET
C961U472JZVDDA7317
Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)
KEMET
C961U472JZWDAA7317
Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)
KEMET
C961U472JZWDBA7317
Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)
KEMET
©2020 ICPDF网 联系我们和版权申明