T496B224M050CT621B [KEMET]
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 50V, 20% +Tol, 20% -Tol, 0.22uF, Surface Mount, 1411, CHIP, ROHS COMPLIANT;型号: | T496B224M050CT621B |
厂家: | KEMET CORPORATION |
描述: | Tantalum Capacitor, Polarized, Tantalum (dry/solid), 50V, 20% +Tol, 20% -Tol, 0.22uF, Surface Mount, 1411, CHIP, ROHS COMPLIANT 电容器 |
文件: | 总19页 (文件大小:1141K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Fused MnO2 Tantalum Surface Mount Capacitors
T496 Series Fail-Safe Fused Space Grade
Overview
KEMET's Space Grade Series of capacitors are suitable for
use by military/aerospace customers in high reliability space
applications. This series meets the requirements of MIL–
PRF–55365 as well as MIL–STD–1580. These capacitors
incorporate an intensive testing and screening protocol which
isꢀcustomizableꢀdependingꢀonꢀspecificꢀcustomerꢀrequirements.ꢀ
The full part number allows for designation of Weibull grading
level (C=0.01%/k hours), surge current level (10 cycles -55°C and
+85°Cꢀbeforeꢀand/orꢀafterꢀWeibullꢀgrading),ꢀperformanceꢀtestingꢀ
level (see chart for details on available options), ESR (low and
standard),ꢀandꢀterminationꢀfinishꢀ(seeꢀdescriptionꢀinꢀeachꢀseries).ꢀ
Fused versions are available for built-in circuit protection, as well
as multi-anode designs for very low ESR values.
Benefits
• Internal fuse protects against damaging short circuit failure mode • RoHS Compliant and lead-free terminations
• Standard case sizes B, C, D, X per EIA 535BAAC
• 100% surge current test available
• Optional gold-plated terminations
• Weibull Grading C (0.01%/1,000 hours)
•ꢀ Capacitanceꢀvaluesꢀofꢀ0.15ꢀμFꢀtoꢀ470ꢀμF
• Voltage rating of 4 – 50 VDC
•ꢀ Operatingꢀtemperatureꢀrangeꢀofꢀ-55˚Cꢀtoꢀ+125˚C
•ꢀ Fuseꢀactivation,ꢀ25˚C:ꢀwithinꢀ1ꢀsecondꢀatꢀfaultꢀcurrentsꢀofꢀ
4 amps and higher
•ꢀ Continuousꢀcurrentꢀcapability:ꢀ0.75ꢀamps
•ꢀ Postꢀactuationꢀresistance,ꢀ25˚C:ꢀ10ꢀMΩ,ꢀminimum
• Test tabs on side of case bypass the capacitor element to
allow direct testing of the fuse assembly
Environmental Compliance
RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn solder.
SPICE
Forꢀaꢀdetailedꢀanalysisꢀofꢀspecificꢀpartꢀnumbers,ꢀpleaseꢀvisitꢀwww.kemet.comꢀforꢀaꢀfreeꢀdownloadꢀofꢀKEMET'sꢀSPICEꢀsoftware.ꢀ
The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over
frequency, temperature, ripple, and DC bias conditions.
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013
1
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Ordering Information
T
T
496
X
227
M
010
C
61
2
A
Capacitor
Class
Capacitance Capacitance
Code (pF) Tolerance
Failure Rate/
Design
Series Case Size
Voltage
Lead Material
Surge
ESR
Testing
T =
Fail
B, C, D, X First two digits K = ±10% 004 = 4 V
C =
T = 100% Matte 61 = None
1 = ESR - A = Option A
Tantalum Safe -
Space
represent
significantꢀ
figures.ꢀThirdꢀ
digitꢀspecifiesꢀ
number of
zeros.
M = ±20% 006 = 6.3 V 0.01%/1,000 Tin (Sn) Plated 62 = 10 Cycles Standard B = Option B
010 = 10 V
016 = 16 V
020 = 20 V
025 = 25 V
035 = 35 V
050 = 50 V
hours
H = Standard
Solder Coated
(SnPb 5% Pb
minimum)
25°C
2 = ESR - C = Option C
Grade
63 = 10 Cycles, Low
-55°C and 85°C
before Weibull
64 = 10 Cycles,
-55°C and 85°C
after Weibull
65 = Both
Applications
Typicalꢀapplicationsꢀincludeꢀdecouplingꢀandꢀfilteringꢀinꢀcomputingꢀandꢀtelecommunicationsꢀendꢀapplications,ꢀsuchꢀasꢀhigh-endꢀserversꢀ
requiring built-in fuse capability.
Performance Characteristics
Item
Performance Characteristics
Operating Temperature
-55°C to 125°C
Rated Capacitance Range
Capacitance Tolerance
Rated Voltage Range
DF (120 Hz)
0.15 – 477 µF @ 120 Hz/25°C
K Tolerance (10%), M Tolerance (20%)
4 – 50 V
ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpecificationꢀTableꢀ
ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpecificationꢀTableꢀ
≤ꢀ0.01ꢀCVꢀ(µA)ꢀatꢀratedꢀvoltageꢀafterꢀ5ꢀminutes
ESR (100 kHz)
Leakage Current
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013
2
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Qualification
Test
Condition
Characteristics
Within ±10% of initial value
Within initial limits
ΔꢀC/C
DF
85°C @ rated voltage, 2,000 hours
125°C @ 2/3 rated voltage, 2,000 hours
Endurance
DCL
ESR
ΔꢀC/C
DF
Within 1.25 x initial limit
Within initial limits
Within ±10% of initial value
Within initial limits
Storage Life
125°C @ 0 Volts, 2,000 hours
DCL
ESR
ΔꢀC/C
DF
Within 1.25 x initial limit
Within initial limits
Within ±5% of initial value
Within initial limits
MIL–STD–202, Method 107, Condition B, mounted, -55C° to
125°C, 1,000 cycles
Thermal Shock
DCL
ESR
+25°C
IL*
Within 1.25 x initial limit
Within initial limits
-55°C
±10%
IL
+85°C
±10%
+125°C
±20%
Extreme temperature exposure at a
successionꢀofꢀcontinuousꢀstepsꢀatꢀ+25ºC,ꢀ
-55ºC,ꢀ+25ºC,ꢀ+85ºC,ꢀ+125ºC,ꢀ+25ºC
ΔꢀC/C
Temperature Stability
DF
IL
1.5 x IL
10 x IL
1.5 x IL
12 x IL
DCL
IL
n/a
ΔꢀC/C
DF
Within ±5% of initial value
Within initial limits
25°C and 85°C, 1.32 x rated voltage 1,000 cycles.
(125°C, 1.2 x rated voltage)
Surge Voltage
DCL
ESR
ΔꢀC/C
DF
Within initial limits
Within initial limits
Within ±10% of initial value
Within initial limits
MIL–STD–202, Method 213, Condition I, 100 G peak.
MIL–STD–202, Method 204, Condition D, 10 Hz to 2,000 Hz,
20 G peak
Mechanical Shock/Vibration
DCL
Within initial limits
*IL = Initial Limit
Certification
DSCC Drawing 04053
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013
3
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Electrical Characteristics
Capacitance vs. Frequency
ESR vs. Frequency
1,000
1000
100
10
T496B106M016ATE3K5
T496B106M016ATE3K5_IMP
T496D476M016ATE400_IMP
T496X107M016ATE700_IMP
T496B106M016ATE3K5_ESR
T496D476M016ATE400_ESR
T496X107M016ATE700_ESR
T496D476M016ATE400
T496X107M016ATE700
100
10
1
1
0
0.1
100
1,000
10,000
Frequency (Hz)
100,000
1,000,000
10,000,000
100
1,000
10,000
100,000
1,000,000
10,000,000
Frequency (Hz)
Dimensions – Millimeters (Inches)
Metric will govern
Termination
cutout at
KEMET’s
option,
either end
Case Size
Component
F* ±0.1 S* ±0.3 B* ±0.15
±(.004) ±(.012) (Ref) ±.006
KEMET EIA
L*
W*
H*
X (Ref)
P (Ref) R (Ref) T (Ref) A (Min) G (Ref) E (Ref)
3.5 ±0.2
2.8 ±0.2
1.9 ±0.2
0.10 ±0.10
(0.004 ±0.004)
3528–21
2.2 (.087) 0.8 (.031)
2.2 (.087) 1.3 (.051)
2.4 (.094) 1.3 (.051)
2.4 (.094) 1.3 (.051)
0.4 (.016)
0.5 (.020)
0.5 (.020)
0.5 (.020)
0.5 (0.020) 1.0 (0.039) 0.13 (0.005) 1.1 (.043) 1.8 (0.071) 2.2 (0.087)
0.9 (0.035) 1.0 (0.039) 0.13 (0.005) 2.5(.098) 2.8 (0.110) 2.4 (0.094)
0.9 (0.035) 1.0 (0.039) 0.13 (0.005) 3.8 (0.150) 3.5 (0.138) 3.5 (0.138)
1.7 (0.067) 1.0 (0.039) 0.13 (0.005) 3.8 (0.150) 3.5 (0.138) 3.5 (0.138)
B
(0.138 ±0.008) (0.110 ±0.008) (0.075 ±0.008)
6.0 ±0.3 3.2 ±0.3 2.5 ±0.3
(0.236 ±0.03) (0.126 ±0.012) (0.098 ±0.012)
7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3
(0.287 ±0.012) (0.169 ±0.012) (0.110 ±0.012)
7.3 ±0.3 4.3 ±0.3 4.0 ±0.3
(0.287 ±0.012) (0.169 ±0.012) (0.157 ±0.012)
0.10 ±0.10
(0.004 ±0.004)
6032–28
C
0.10 ±0.10
(0.004 ±0.004)
7343–31
D
0.10 ±0.10
(0.004 ±0.004)
7343–43
X
Notes: (Ref) – Dimensions provided for reference only. No dimensions provided for B, P or R because low profile cases do not have a bevel or a notch.
* MIL–C–55365/8 specified dimensions
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013
4
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Table 1 – Ratings & Part Number Reference
Rated
Rated
Case Code/
DC
Leakage
µA @ +20ºC
Standard
ESR
Moisture
Sensitivity
Temperature
≤ 260ºC
KEMET Part Number
DF
Low ESR
Voltage Capacitance Case Size
% @ +20ºC
Ω @ +20ºC
Ω @ +20ºC
(See below for
part options)
V
µF
KEMET/EIA
Maximum/5 Min 120 Hz Maximum 100 kHz Maximum 100 kHz Maximum
4
4
4
4
4
4
4
4
68
C/6032-28
C/6032-28
C/6032-28
D/7343-31
D/7343-31
D/7343-31
X/7343-43
X/7343-43
T496C686(1)004(2)(3)(4)(5)(6)
T496C107(1)004(2)(3)(4)(5)(6)
T496C157(1)004(2)(3)(4)(5)(6)
T496D157(1)004(2)(3)(4)(5)(6)
T496D227(1)004(2)(3)(4)(5)(6)
T496D337(1)004(2)(3)(4)(5)(6)
T496X337(1)004(2)(3)(4)(5)(6)
T496X477(1)004(2)(3)(4)(5)(6)
2.7
4
6
6
8
8
8
8
8
8
8
1.6
1.2
1.2
0.8
0.7
0.7
0.7
0.5
0.4
N/A
N/A
N/A
0.4
0.4
N/A
N/A
1
1
1
1
1
1
1
1
100
150
150
220
330
330
470
6
8.8
13.2
13.2
18.8
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
4.7
6.8
10
22
15
22
33
47
47
B/3528-21
B/3528-21
B/3528-21
B/3528-21
C/6032-28
C/6032-28
C/6032-28
C/6032-28
D/7343-31
C/6032-28
D/7343-31
C/6032-28
D/7343-31
X/7343-43
D/7343-31
X/7343-43
X/7343-43
D/7343-31
X/7343-43
T496B475(1)006(2)(3)(4)(5)(6)
T496B685(1)006(2)(3)(4)(5)(6)
T496B106(1)006(2)(3)(4)(5)(6)
T496B226(1)006(2)(3)(4)(5)(6)
T496C156(1)006(2)(3)(4)(5)(6)
T496C226(1)006(2)(3)(4)(5)(6)
T496C336(1)006(2)(3)(4)(5)(6)
T496C476(1)006(2)(3)(4)(5)(6)
T496D476(1)006(2)(3)(4)(5)(6)
T496C686(1)006(2)(3)(4)(5)(6)
T496D686(1)006(2)(3)(4)(5)(6)
T496C107(1)006(2)(3)(4)(5)(6)
T496D107(1)006(2)(3)(4)(5)(6)
T496X107(1)006(2)(3)(4)(5)(6)
T496D157(1)006(2)(3)(4)(5)(6)
T496X157(1)006(2)(3)(4)(5)(6)
T496X227(1)006(2)(3)(4)(5)(6)
T496D227(1)006(2)(3)(4)(5)(6)
T496X337(1)006(2)(3)(4)(5)(6)
0.5
0.5
0.6
1.3
0.9
1.4
2
2.9
2.9
4.1
4.1
6
6
6
9
9
13.2
13.2
19.8
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
3.5
3.5
3.5
3.5
2
2
2
1.6
1
1.2
1
0.4
0.8
0.9
0.7
0.3
0.7
0.7
0.5
N/A
N/A
N/A
1.5
N/A
N/A
0.6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0.6
N/A
N/A
N/A
N/A
0.4
0.3
0.3
N/A
0.3
0.3
0.3
68
68
100
100
100
150
150
220
220
330
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
3.3
4.7
6.8
10
15
15
22
33
33
47
47
68
68
100
100
150
150
220
B/3528-21
B/3528-21
B/3528-21
C/6032-28
B/3528-21
C/6032-28
C/6032-28
C/6032-28
D/7343-31
C/6032-28
D/7343-31
D/7343-31
X/7343-43
D/7343-31
X/7343-43
D/7343-31
X/7343-43
X/7343-43
T496B335(1)010(2)(3)(4)(5)(6)
T496B475(1)010(2)(3)(4)(5)(6)
T496B685(1)010(2)(3)(4)(5)(6)
T496C106(1)010(2)(3)(4)(5)(6)
T496B156(1)010(2)(3)(4)(5)(6)
T496C156(1)010(2)(3)(4)(5)(6)
T496C226(1)010(2)(3)(4)(5)(6)
T496C336(1)010(2)(3)(4)(5)(6)
T496D336(1)010(2)(3)(4)(5)(6)
T496C476(1)010(2)(3)(4)(5)(6)
T496D476(1)010(2)(3)(4)(5)(6)
T496D686(1)010(2)(3)(4)(5)(6)
T496X686(1)010(2)(3)(4)(5)(6)
T496D107(1)010(2)(3)(4)(5)(6)
T496X107(1)010(2)(3)(4)(5)(6)
T496D157(1)010(2)(3)(4)(5)(6)
T496X157(1)010(2)(3)(4)(5)(6)
T496X227(1)010(2)(3)(4)(5)(6)
0.5
0.5
0.7
1
6
6
6
6
6
6
6
6
6
6
6
6
6
8
8
8
8
8
3.5
3.5
3.5
2
3.5
2
2
1.6
1
N/A
N/A
N/A
N/A
N/A
0.6
0.5
0.4
0.4
0.4
0.4
0.4
N/A
0.4
N/A
0.4
0.4
0.3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1.5
1.5
2.2
3.3
3.3
4.7
4.7
6.8
6.8
10
1.2
1
0.8
0.9
0.7
0.4
0.7
0.7
0.5
10
15
15
22
T
496
Series Case Size
X
227
M
010
C
T
61
2
A
Capacitor
Class
Capacitance Capacitance
Failure Rate/
Voltage
Lead Material
Surge
ESR
Testing
Code (pF)
Tolerance
Design
1 = ESR - A = Option A
V
C =
T =
Fail
B, C, D, X First two digits K = ±10% 004 = 4 V
T = 100% Matte 61 = None
Tantalum Safe -
represent
M = ±20% 006 = 6.3 V 0.01%/1,000 Tin (Sn) Plated 62 = 10 Cycles Standard B = Option B
25°C 2 = ESR - C = Option C
63 = 10 Cycles, Low
(1) T
Space signi ꢀcantꢀ 010 = 10 V hours H = Standard
(2) T
Grade ꢀgures.ꢀThirdꢀ 016 = 16 V Solder Coated
(3) T
digitꢀspeci ꢀesꢀ 020 = 20 V (SnPb 5% Pb -55°C and 85°C
(4) T
number of
zeros.
025 = 25 V
035 = 35 V
minimum)
before Weibull
64 = 10 Cycles,
-55°C and 85°C
Weib
(5) T
050 = 50 V
(6) T
after Weibull
65 = Both
infor
Refe
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013
5
Roll Over for
Order Info.
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Table 1 – Ratings & Part Number Reference cont'd
Rated
Rated
Case Code/
DC
Leakage
µA @ +20ºC
Standard
ESR
Moisture
Sensitivity
Temperature
≤ 260ºC
KEMET Part Number
DF
Low ESR
Voltage Capacitance Case Size
% @ +20ºC
Ω @ +20ºC
Ω @ +20ºC
(See below for
part options)
V
µF
KEMET/EIA
Maximum/5 Min 120 Hz Maximum 100 kHz Maximum 100 kHz Maximum
16
16
16
16
16
16
16
16
16
16
16
3.3
4.7
6.8
10
15
22
22
33
47
47
68
B/3528-21
B/3528-21
C/6032-28
C/6032-28
C/6032-28
C/6032-28
D/7343-31
D/7343-31
D/7343-31
X/7343-43
D/7343-31
T496B335(1)016(2)(3)(4)(5)(6)
T496B475(1)016(2)(3)(4)(5)(6)
T496C685(1)016(2)(3)(4)(5)(6)
T496C106(1)016(2)(3)(4)(5)(6)
T496C156(1)016(2)(3)(4)(5)(6)
T496C226(1)016(2)(3)(4)(5)(6)
T496D226(1)016(2)(3)(4)(5)(6)
T496D336(1)016(2)(3)(4)(5)(6)
T496D476(1)016(2)(3)(4)(5)(6)
T496X476(1)016(2)(3)(4)(5)(6)
T496D686(1)016(2)(3)(4)(5)(6)
0.5
0.8
1.1
6
6
6
6
6
6
6
6
6
6
8
3.5
3.5
2
2
2
1.6
1
1
0.8
0.9
0.4
2.1
1.6
0.6
0.7
0.6
1
0.5
0.4
0.4
0.4
N/A
1
1
1
1
1
1
1
1
1
1
1
1.6
2.4
3.6
3.6
5.3
7.5
7.5
10.9
20
20
20
20
20
20
20
20
20
20
1.5
2.2
4.7
6.8
10
15
15
22
33
33
B/3528-21
B/3528-21
C/6032-28
C/6032-28
C/6032-28
C/6032-28
D/7343-31
D/7343-31
D/7343-31
X/7343-43
T496B155(1)020(2)(3)(4)(5)(6)
T496B225(1)020(2)(3)(4)(5)(6)
T496C475(1)020(2)(3)(4)(5)(6)
T496C685(1)020(2)(3)(4)(5)(6)
T496C106(1)020(2)(3)(4)(5)(6)
T496C156(1)020(2)(3)(4)(5)(6)
T496D156(1)020(2)(3)(4)(5)(6)
T496D226(1)020(2)(3)(4)(5)(6)
T496D336(1)020(2)(3)(4)(5)(6)
T496X336(1)020(2)(3)(4)(5)(6)
0.5
0.5
1
1.4
2
3
3
4.4
6.6
6.6
6
6
6
6
6
6
6
6
6
6
5
3.5
2
2
2
0.5
1
1
0.4
0.9
N/A
1.6
N/A
0.6
0.8
N/A
0.5
0.5
0.4
0.4
1
1
1
1
1
1
1
1
1
1
25
25
25
25
25
25
25
25
25
25
25
25
25
0.68
1
B/3528-21
B/3528-21
B/3528-21
C/6032-28
C/6032-28
B/3528-21
C/6032-28
C/6032-28
D/7343-31
C/6032-28
D/7343-31
D/7343-31
X/7343-43
T496B684(1)025(2)(3)(4)(5)(6)
T496B105(1)025(2)(3)(4)(5)(6)
T496B155(1)025(2)(3)(4)(5)(6)
T496C225(1)025(2)(3)(4)(5)(6)
T496C335(1)025(2)(3)(4)(5)(6)
T496B475(1)025(2)(3)(4)(5)(6)
T496C475(1)025(2)(3)(4)(5)(6)
T496C685(1)025(2)(3)(4)(5)(6)
T496D106(1)025(2)(3)(4)(5)(6)
T496C156(1)025(2)(3)(4)(5)(6)
T496D156(1)025(2)(3)(4)(5)(6)
T496D226(1)025(2)(3)(4)(5)(6)
T496X226(1)025(2)(3)(4)(5)(6)
0.5
0.5
0.5
0.6
0.9
1.2
1.2
1.7
2.5
3.8
3.8
5.5
5.5
4
4
6
6
6
6
6
6
6
6
6
6
6
6.5
5
5
3.5
2.5
4
2.5
2
1.2
0.75
1
0.8
0.9
N/A
3.5
1.6
N/A
2.1
N/A
1.3
0.6
0.6
N/A
0.5
0.4
0.4
1
1
1
1
1
1
1
1
1
1
1
1
1
1.5
2.2
3.3
4.7
4.7
6.8
10
15
15
22
22
35
35
35
35
35
35
35
35
35
35
0.47
0.68
1
1.5
2.2
3.3
4.7
6.8
10
B/3528-21
B/3528-21
B/3528-21
C/6032-28
C/6032-28
C/6032-28
D/7343-31
D/7343-31
D/7343-31
X/7343-43
T496B474(1)035(2)(3)(4)(5)(6)
T496B684(1)035(2)(3)(4)(5)(6)
T496B105(1)035(2)(3)(4)(5)(6)
T496C155(1)035(2)(3)(4)(5)(6)
T496C225(1)035(2)(3)(4)(5)(6)
T496C335(1)035(2)(3)(4)(5)(6)
T496D475(1)035(2)(3)(4)(5)(6)
T496D685(1)035(2)(3)(4)(5)(6)
T496D106(1)035(2)(3)(4)(5)(6)
T496X106(1)035(2)(3)(4)(5)(6)
0.5
0.5
0.5
0.5
0.8
1.2
1.7
2.4
3.5
3.5
4
4
4
6
6
6
6
6
6
6
8
6.5
5
4.5
3.5
2.5
1.5
1.3
0.5
1
2.6
N/A
3.1
2.6
1.6
0.9
0.7
0.75
N/A
0.5
1
1
1
1
1
1
1
1
1
1
10
T
496
X
227
M
010
C
T
61
2 A
Capacitor
Capacitance Capacitance
Failure Rate/
Series Case Size
Voltage
Lead Material
Surge
ESR
Testing
Class
V
T =
Code (pF)
Tolerance
Design
C =
Fail
B, C, D, X First two digits K = ±10% 004 = 4 V
T = 100% Matte 61 = None
1 = ESR - A = Option A
M = ±20% 006 = 6.3 V 0.01%/1,000 Tin (Sn) Plated 62 = 10 Cycles Standard B = Option B
010 = 10 V hours H = Standard 25°C 2 = ESR - C = Option C
(1) T
Tantalum Safe - represent
(2) T
Space signi ꢀcantꢀ
Grade ꢀgures.ꢀThirdꢀ 016 = 16 V Solder Coated 63 = 10 Cycles, Low
(3) T
digitꢀspeci ꢀesꢀ 020 = 20 V (SnPb 5% Pb -55°C and 85°C
(4) T
number of
zeros.
025 = 25 V
035 = 35 V
050 = 50 V
minimum)
before Weibull
64 = 10 Cycles,
-55°C and 85°C
after Weibull
65 = Both
Weib
(5) T
(6) T
infor
Refe
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013
6
Roll Over for
Order Info.
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Table 1 – Ratings & Part Number Reference cont'd
Rated
Rated
Case Code/
DC
Leakage
µA @ +20ºC
Standard
ESR
Moisture
Sensitivity
Temperature
≤ 260ºC
KEMET Part Number
DF
Low ESR
Voltage Capacitance Case Size
% @ +20ºC
Ω @ +20ºC
Ω @ +20ºC
(See below for
part options)
V
µF
KEMET/EIA
Maximum/5 Min 120 Hz Maximum 100 kHz Maximum 100 kHz Maximum
50
50
50
50
50
50
50
50
50
50
50
0.15
0.22
0.33
0.47
0.68
1
1.5
2.2
3.3
4.7
B/3528-21
B/3528-21
B/3528-21
C/6032-28
C/6032-28
C/6032-28
C/6032-28
D/7343-31
D/7343-31
D/7343-31
X/7343-43
T496B154(1)050(2)(3)(4)(5)(6)
T496B224(1)050(2)(3)(4)(5)(6)
T496B334(1)050(2)(3)(4)(5)(6)
T496C474(1)050(2)(3)(4)(5)(6)
T496C684(1)050(2)(3)(4)(5)(6)
T496C105(1)050(2)(3)(4)(5)(6)
T496C155(1)050(2)(3)(4)(5)(6)
T496D225(1)050(2)(3)(4)(5)(6)
T496D335(1)050(2)(3)(4)(5)(6)
T496D475(1)050(2)(3)(4)(5)(6)
T496X475(1)050(2)(3)(4)(5)(6)
0.5
0.5
0.5
0.5
0.5
0.5
0.8
1.1
4
4
4
4
4
4
6
6
16
14
10
8
7
5.5
5
2.5
N/A
10
2.6
1.9
1.7
2.7
2
0.9
1
1
1
1
1
1
1
1
1
1
1
1.7
2.4
2.4
6
6
6
2
0.4
1.5
1
N/A
0.4
4.7
µA @ +20ºC
% @ +20ºC
Ω @ +20ºC
Ω @ +20ºC
Temperature
≤ 260ºC
(See below for
part options)
V
µF
KEMET/EIA
Maximum/5 Min 120 Hz Maximum 100 kHz Maximum 100 kHz Maximum
Rated
Voltage
Rated
Capacitance
Case Code/
Case Size
DC
Leakage
Moisture
Sensitivity
KEMET Part Number
DF
Standard ESR
Low ESR
(1) To complete KEMET part number, insert M for ±20%, K for ±10%. Designates Capacitance tolerance.
(2) To complete KEMET part number, insert C (0.01%/1,000 hours). Designates Reliability Level.
(3) To complete KEMET part number, insert H = Solder Plated or T = 100% Tin (Sn). Designates Termination Finish.
(4) To complete KEMET part number, insert 61 = None, 62 = 10 cycles +25°C, 63 = 10 cycles -55°C +85°C after Weibull, 64 = 10 cycles -55°C +85°C before
Weibull or 65 = Both. Designates Surge current option.
(5) To complete KEMET part number, insert 1 = Standard ESR, 2 = Low ESR. Designates ESR option.
(6) To complete KEMET part number, insert A = Option 1, B = Option 2 or C = Option 3. Designates Test Option. See Space Grade Test Methods chart for more
information.
Refer to Ordering Information for additional detail.
T
496
X
227
M
010
C
T
61
2
A
Capacitor
Class
Capacitance Capacitance
Code (pF) Tolerance
Failure Rate/
Design
Series Case Size
Voltage
Lead Material
Surge
ESR
Testing
T =
Fail
B, C, D, X First two digits K = ±10% 004 = 4 V
C =
T = 100% Matte 61 = None
1 = ESR - A = Option A
Tantalum Safe -
Space
represent
signi ꢀcantꢀ
ꢀgures.ꢀThirdꢀ
digitꢀspeci ꢀesꢀ
number of
zeros.
M = ±20% 006 = 6.3 V 0.01%/1,000 Tin (Sn) Plated 62 = 10 Cycles Standard B = Option B
010 = 10 V
016 = 16 V
020 = 20 V
025 = 25 V
035 = 35 V
050 = 50 V
hours
H = Standard
Solder Coated
(SnPb 5% Pb
minimum)
25°C
2 = ESR - C = Option C
Grade
63 = 10 Cycles, Low
-55°C and 85°C
before Weibull
64 = 10 Cycles,
-55°C and 85°C
after Weibull
65 = Both
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013
7
Roll Over for
Order Info.
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Recommended Voltage Derating Guidelines
1.2
1
-55°C to 125°C
% Change in Working DC
50% of VR
VR
VR
Voltage with Temperature
Recommended Maximum
Application Voltage
0.8
0.6
0.4
0.2
0
100% of VR
% Change in Working DC Voltage
with Temperature
67%
33%
Recommended Maximum Application
Voltage (As % of Rated Voltage)
-55
25
85
125
Temperature (ºC)
Ripple Current/Ripple Voltage
Temperature Compensation Multipliers
for Maximum Power Dissipation
Maximum Power
Dissipation (P max)
mWatts @ 25°C
KEMET Series
and Case Code
EIA
Case Code
≤ꢀ25°C
85°C
125°C
1.00
0.90
0.40
w/+20°C Rise
A
3216–18
3528–21
6032–28
7343–31
7343–43
7360–38
7360–38
2012–12
3216–12
3528–12
6032–15
7343–20
7343–43
7360–38
75
T= Environmental Temperature
B
85
C
110
150
165
200
325
25
Using the P max of the device, the maximum allowable rms ripple
current or voltage may be determined.
D
X
E
I(max) = √P max/R
E(max) = √P max*R
T428P
R
I = rms ripple current (amperes)
E = rms ripple voltage (volts)
P max = maximum power dissipation(watts)
R = ESR at specified frequency (ohms)
S
T
60
70
U
90
V
125
270
285
T510X
T510E
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013
8
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Reverse Voltage
Solid tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected with the wrong polarity. The
positiveꢀterminalꢀisꢀidentifiedꢀonꢀtheꢀcapacitorꢀbodyꢀbyꢀaꢀstripeꢀplusꢀinꢀsomeꢀcasesꢀaꢀbeveledꢀedge.ꢀAꢀsmallꢀdegreeꢀofꢀtransientꢀreverseꢀ
voltage is permissible for short periods per the table. The capacitors should not be operated continuously in reverse mode, even within
these limits.
Temperature
Permissible Transient Reverse Voltage
25°C
85°C
15% of Rated Voltage
5% of Rated Voltage
1% of Rated Voltage
125°C
Table 2 – Land Dimensions/Courtyard
Metric
Size
Code
Density Level A:
Maximum (Most) Land
Protrusion (mm)
Density Level B:
Median (Nominal) Land
Protrusion (mm)
Density Level C:
Minimum (Least) Land
Protrusion (mm)
KEMET
Case
EIA
X
Y
C
V1
V2
X
Y
C
V1
V2
X
Y
C
V1
V2
B
3528–21
2.35
2.15
1.45
6.10
4.00
2.25
1.75
1.35
5.00
3.50
2.15
1.35
1.25
4.10
3.20
C
D
6032–28
7343–31
7343–43
2.35
2.55
2.55
2.65
3.75
3.75
2.60
2.70
2.70
8.90
10.20
10.20
4.40
5.50
5.50
2.25
2.45
2.45
2.25
3.35
3.35
2.50
2.60
2.60
7.80
9.10
9.10
3.90
5.00
5.00
2.15
2.35
2.35
1.85
2.95
2.95
2.40
2.50
2.50
6.90
8.20
8.20
3.60
4.70
4.70
X¹
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes.
Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification
testing based on the conditions outlined in IPC Standard 7351 (IPC–7351).
¹ Height of these chips may create problems in wave soldering.
² Land pattern geometry is too small for silkscreen outline
.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013
9
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Soldering Process
KEMET’s families of surface mount capacitors are compatible
Profile Feature
SnPb Assembly Pb-Free Assembly
withꢀwaveꢀ(singleꢀorꢀdual),ꢀconvection,ꢀIR,ꢀorꢀvaporꢀphaseꢀreflowꢀ
techniques. Preheating of these components is recommended
toꢀavoidꢀextremeꢀthermalꢀstress.ꢀKEMET'sꢀrecommendedꢀprofileꢀ
conditionsꢀforꢀconvectionꢀandꢀIRꢀreflowꢀreflectꢀtheꢀprofileꢀconditionsꢀ
of the IPC/J–STD–020D standard for moisture sensitivity testing.
Theꢀdevicesꢀcanꢀsafelyꢀwithstandꢀaꢀmaximumꢀofꢀthreeꢀreflowꢀ
passes at these conditions.
Preheat/Soak
Temperature Minimum (TSmin
)
100°C
150°C
150°C
200°C
Temperature Maximum (TSmax
)
Time (ts) from Tsmin to Tsmax
)
60 – 120 seconds
3°C/seconds maximum
183°C
60 – 120 seconds
3°C/seconds maximum
217°C
Ramp-up Rate (TL to TP)
Liquidous Temperature (TL)
Time Above Liquidous (tL)
60 – 150 seconds
60 – 150 seconds
220°C*
235°C**
250°C*
260°C**
Peak Temperature (TP)
Please note that although the X/7343–43 case size can withstand
waveꢀsoldering,ꢀtheꢀtallꢀprofileꢀ(4.3ꢀmmꢀmaximum)ꢀdictatesꢀcareꢀinꢀ
wave process development.
Time within 5°C of Maximum
Peak Temperature (tP)
20 seconds maximum
6°C/seconds maximum
6 minutes maximum
30 seconds maximum
6°C/seconds maximum
8 minutes maximum
Ramp-down Rate (TP to TL)
Time 25°C to Peak Temperature
Handꢀsolderingꢀshouldꢀbeꢀperformedꢀwithꢀcareꢀdueꢀtoꢀtheꢀdifficultyꢀ
in process control. If performed, care should be taken to avoid
contact of the soldering iron to the molded case. The iron should
be used to heat the solder pad, applying solder between the pad
andꢀtheꢀtermination,ꢀuntilꢀreflowꢀoccurs.ꢀOnceꢀreflowꢀoccurs,ꢀtheꢀ
iron should be removed immediately. “Wiping” the edges of a chip
and heating the top surface is not recommended.
Note: All temperatures refer to the center of the package, measured on the
package body surface that is facing up during assembly reflow.
*Case Size D, E, P, Y, and X
**Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z
TP
tP
Maximum Ramp Up Rate = 3ºC/seconds
Maximum Ramp Down Rate = 6ºC/seconds
TL
tL
Duringꢀtypicalꢀreflowꢀoperations,ꢀaꢀslightꢀdarkeningꢀofꢀtheꢀgold-
colored epoxy may be observed. This slight darkening is normal
and not harmful to the product. Marking permanency is not
affected by this change.
T
smax
T
smin
tS
25
25ºC to Peak
Time
Construction
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013 10
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Capacitor Marking
KEMET
Fused
MnO2
Polarity
Indicator (+)
S+
Picofarad Code
KEMET ID
227
10 K
230
Rated
Voltage
Date
Code *
* 230 = 30th week of 2012
Date Code *
1st digit = Last number of Year
9 = 2009
0 = 2010
1 = 2011
2 = 2012
3 = 2013
4 = 2014
2nd and 3rd digit = Week of the Year
01 = 1st week of the Year to
52 = 52nd week of the Year
Storage
Tantalum chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other
environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term
storage. In addition, packaging materials will be degraded by high temperature– reels may soften or warp and tape peel force may
increase.ꢀKEMETꢀrecommendsꢀthatꢀmaximumꢀstorageꢀtemperatureꢀnotꢀexceedꢀ40ºCꢀandꢀmaximumꢀstorageꢀhumidityꢀnotꢀexceedꢀ60%ꢀ
relativeꢀhumidity.ꢀTemperatureꢀfluctuationsꢀshouldꢀbeꢀminimizedꢀtoꢀavoidꢀcondensationꢀonꢀtheꢀpartsꢀandꢀatmospheresꢀshouldꢀbeꢀfreeꢀofꢀ
chlorine and sulphur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within three years
of receipt.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013 11
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Tape & Reel Packaging Information
KEMET’s molded tantalum and aluminum chip capacitor families are packaged in 8 and 12 mm plastic tape on 7" and 13" reels in
accordance with EIA Standard 481–1:ꢀEmbossedꢀCarrierꢀTapingꢀofꢀSurfaceꢀMountꢀComponentsꢀforꢀAutomaticꢀHandling.ꢀThisꢀpackagingꢀ
system is compatible with all tape-fed automatic pick-and-place systems.
8 mm (0.315")
or
12 mm (0.472")
180 mm (7.0")
Top Tape Thickness
or
0.10 mm (0.004")
330 mm (13.0")
Maximum Thickness
Table 3 – Packaging Quantity
Tape Width
Case Code
7" Reel*
13" Reel*
(mm)
KEMET
EIA
I
S
T
M
U
L
W
Z
V
A
B
C
D
Y
3216-10
3216-12
3528-12
3528-15
6032-15
6032-19
7343-15
7343-17
7343-20
3216-18
3528-21
6032-28
7343-31
7343-40
7343-43
7360-38
7360-20
8
8
8
8
12
12
12
12
12
8
3,000
2,500
2,500
2,000
1,000
1,000
1,000
1,000
1,000
2,000
2,000
500
12,000
10,000
10,000
8,000
5,000
5,000
3,000
3,000
3,000
9,000
8,000
3,000
2,500
2,000
2,000
2,000
2,500
8
12
12
12
12
12
12
500
500
500
500
X
E/T428P
H
1,000
* No C-Spec required for 7" reel packaging. C-7280 required for 13" reel packaging.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013 12
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
T
T
P2
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
2
E
1
Po
ØDo
Ao
F
Ko
W
E
2
B
1
Bo
S
1
P
1
T
1
Embossment
For cavity size,
see Note 1 Table 4
Center Lines of Cavity
ØD
1
Cover Tape
is for tape feeder reference only,
including draft concentric about B
B
1
o
.
User Direction of Unreeling
Table 4 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
D1 Minimum
Note 1
1.0
R Reference S1 Minimum
Tape Size
8 mm
D0
E1
P0
P2
T Maximum T1 Maximum
Note 2
Note 3
25.0
(0.984)
(0.039)
1.5ꢀ+0.10/-0.0ꢀ
(0.059ꢀ+0.004/-0.0)
1.75 ±0.10
4.0 ±0.10
2.0 ±0.05
0.600
(0.024)
0.600
(0.024)
0.100
(0.004)
12 mm
16 mm
(0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002)
1.5
(0.059)
30
(1.181)
Variable Dimensions — Millimeters (Inches)
B1 Maximum
Note 4
4.35
(0.171)
8.2
(0.323)
12.1
(0.476)
Tape Size
8 mm
Pitch
E2 Minimum
F
P1
T2 Maximum W Maximum
A0,B0 & K0
6.25
(0.246)
10.25
(0.404)
14.25
3.5 ±0.05
4.0 ±0.10
2.5
(0.098)
4.6
8.3
(0.327)
12.3
Single (4 mm)
(0.138 ±0.002) (0.157 ±0.004)
5.5 ±0.05 8.0 ±0.10
(0.217 ±0.002) (0.315 ±0.004)
5.5 ±0.05 8.0 ±0.10
(0.217 ±0.002) (0.315 ±0.004)
Single (4 mm) &
Double (8 mm)
12 mm
16 mm
Note 5
(0.181)
4.6
(0.484)
16.3
Triple (12 mm)
(0.561)
(0.181)
(0.642)
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
2. The tape, with or without components, shall pass around R without damage (see Figure 5).
3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481–D, paragraph 4.3, section b).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 2).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 3).
(e) see Addendum in EIA Standard 481–D for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013 13
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Packaging Information Performance Notes
1. Cover Tape Break Force: 1.0 Kg minimum.
2. Cover Tape Peel Strength: Theꢀtotalꢀpeelꢀstrengthꢀofꢀtheꢀcoverꢀtapeꢀfromꢀtheꢀcarrierꢀtapeꢀshallꢀbe:ꢀ
Tape Width
8 mm
Peel Strength
0.1 to 1.0 Newton (10 to 100 gf)
0.1 to 1.3 Newton (10 to 130 gf)
12 and 16 mm
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180°
from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute.
3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA
Standards 556 and 624.
Figure 2 – Maximum Component Rotation
°
T
Maximum Component Rotation
Top View
Maximum Component Rotation
Side View
Typical Pocket Centerline
Tape
Maximum
°
°
T
s
Width (mm) Rotation (
)
8,12
16 – 200
20
10
Bo
Tape
Maximum
°
S
Width (mm) Rotation (
)
8,12
16 – 56
72 – 200
20
10
5
Typical Component Centerline
Ao
Figure 4 – Bending Radius
Figure 3 – Maximum Lateral Movement
Embossed
Carrier
Punched
Carrier
8 mm & 12 mm Tape
16 mm Tape
0.5 mm maximum
0.5 mm maximum
1.0 mm maximum
1.0 mm maximum
R
Bending
Radius
R
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013 14
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Figure 5 – Reel Dimensions
Full Radius,
W3 (Includes
flange distortion
at outer edge)
Access Hole at
Slot Location
(Ø 40 mm minimum)
See Note
W
2 (Measured at hub)
D
(See Note)
A
N
C
(Arbor hole
W
1 (Measured at hub)
diameter)
If present,
tape slot in core
for tape start:
2.5 mm minimum width x
10.0 mm minimum depth
B
(see Note)
Note: Drive spokes optional; if used, dimensions B and D shall apply.
Table 5 – Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
8 mm
A
B Minimum
C
D Minimum
178 ±0.20
(7.008 ±0.008)
or
330 ±0.20
(13.000 ±0.008)
1.5
(0.059)
13.0ꢀ+0.5/-0.2ꢀ
(0.521ꢀ+0.02/-0.008)
20.2
(0.795)
12 mm
16 mm
Variable Dimensions — Millimeters (Inches)
Tape Size
8 mm
N Minimum
W1
W2 Maximum
W3
8.4ꢀ+1.5/-0.0
(0.331ꢀ+0.059/-0.0)
12.4ꢀ+2.0/-0.0
(0.488ꢀ+0.078/-0.0)ꢀꢀ
16.4ꢀ+2.0/-0.0
14.4
(0.567)
18.4
(0.724)
22.4
50
(1.969)
Shall accommodate tape width
without interference
12 mm
16 mm
(0.646ꢀ+0.078/-0.0)
(0.882)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013 15
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Figure 6 – Tape Leader & Trailer Dimensions
Embossed Carrier
Carrier Tape
Round Sprocket Holes
Punched Carrier
8 mm & 12 mm only
START
END
Top Cover Tape
Elongated Sprocket Holes
(32 mm tape and wider)
100 mm
Minimum Leader
400 mm Minimum
Trailer
160 mm Minimum
Components
Top Cover Tape
Figure 7 – Maximum Camber
Elongated sprocket holes
(32 mm & wider tapes)
Carrier Tape
Round Sprocket Holes
1 mm Maximum, either direction
Straight Edge
250 mm
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013 16
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Paris, France
Tel:ꢀ33-1-4646-1006ꢀ
Northeast Asia
Hong Kong
Tel:ꢀ852-2305-1168
2835 KEMET Way
Simpsonville, SC 29681
Sasso Marconi, Italy
Tel:ꢀ39-051-939111
Shenzhen, China
Tel:ꢀ86-755-2518-1306
MailingꢀAddress:
P.O. Box 5928
Greenville, SC 29606
Beijing, China
Central Europe
Tel:ꢀ86-10-5829-1711
www.kemet.com
Landsberg, Germany
Tel:ꢀ49-8191-3350800ꢀꢀ
Tel:ꢀ864-963-6300ꢀ
Fax:ꢀ864-963-6521
Shanghai, China
Tel:ꢀ86-21-6447-0707
Kamen, Germany
Tel:ꢀ49-2307-438110
Corporate Offices
Fort Lauderdale, FL
Tel:ꢀ954-766-2800
Taipei, Taiwan
Tel:ꢀ886-2-27528585
Northern Europe
Bishop’s Stortford, United Kingdom
Tel:ꢀ44-1279-460122ꢀ
North America
Southeast Asia
Singapore
Southeast
Tel:ꢀ65-6586-1900
Lake Mary, FL
Tel:ꢀ407-855-8886
Espoo, Finland
Tel:ꢀ358-9-5406-5000
Penang, Malaysia
Tel:ꢀ60-4-6430200
Northeast
Wilmington, MA
Tel:ꢀ978-658-1663ꢀ
Bangalore, India
Tel:ꢀ91-806-53-76817
Central
Novi, MI
Tel:ꢀ248-994-1030
West
Milpitas, CA
Tel:ꢀ408-433-9950
Mexico
Guadalajara, Jalisco
Tel:ꢀ52-33-3123-2141ꢀꢀ
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013 17
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Other KEMET Resources
Tools
Resource
Location
Con ꢀgureꢀAꢀPart:ꢀCapEdge
SPICE & FIT Software
http://capacitoredge.kemet.com
http://www.kemet.com/spice
http://www.kemet.com/keask
http://www.kemet.com:8080/elc
SearchꢀOurꢀFAQs:ꢀKnowledgeEdge
Electrolytic LifeCalculator
Product Information
Resource
Location
Products
Technical Resources (Including Soldering Techniques)
RoHS Statement
http://www.kemet.com/products
http://www.kemet.com/technicalpapers
http://www.kemet.com/rohs
Quality Documents
http://www.kemet.com/qualitydocuments
Product Request
Resource
Resource
Location
http://www.kemet.com/sample
http://www.kemet.com/kits
Sample Request
Engineering Kit Request
Contact
Location
Website
Contact Us
Investor Relations
Call Us
www.kemet.com
http://www.kemet.com/contact
http://www.kemet.com/ir
1-877-MyKEMET
Twitter
http://twitter.com/kemetcapacitors
Disclaimer
Allꢀproductꢀspeci ꢀcations,ꢀstatements,ꢀinformationꢀandꢀdataꢀ(collectively,ꢀtheꢀ“Information”)ꢀinꢀthisꢀdatasheetꢀareꢀsubjectꢀtoꢀchange.ꢀTheꢀcustomerꢀisꢀresponsibleꢀforꢀcheckingꢀandꢀ
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are
notꢀintendedꢀtoꢀconstituteꢀ–ꢀandꢀKEMETꢀspeci ꢀcallyꢀdisclaimsꢀ–ꢀanyꢀwarrantyꢀconcerningꢀsuitabilityꢀforꢀaꢀspeci ꢀcꢀcustomerꢀapplicationꢀorꢀuse.ꢀTheꢀInformationꢀisꢀintendedꢀforꢀuseꢀonlyꢀ
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013 18
Tantalum Surface Mount Capacitors
Fused MnO2 Tantalum Surface Mount Capacitors – T496 Series Fail-Safe Fused Space Grade
Digitally signed by Jeannette Calvo
DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corp., ou=Marketing Communications,
cn=Jeannette Calvo, email=jeannettecalvo@kemet.com
Date: 2013.07.19 15:48:29 -04'00'
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2026_T496_SPACE • 7/19/2013 19
相关型号:
T496B225K016AT
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 16V, 10% +Tol, 10% -Tol, 2.2uF, Surface Mount, 1411, CHIP, ROHS COMPLIANT
KEMET
T496B225K020AHE3K5
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 20V, 10% +Tol, 10% -Tol, 2.2uF, Surface Mount, 1411, CHIP
KEMET
T496B225K020AT
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 20V, 10% +Tol, 10% -Tol, 2.2uF, Surface Mount, 1411, CHIP, ROHS COMPLIANT
KEMET
T496B225K020ATE3K5
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 20V, 10% +Tol, 10% -Tol, 2.2uF, Surface Mount, 1411, CHIP
KEMET
T496B225K020CT612B
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 20V, 10% +Tol, 10% -Tol, 2.2uF, 1411
KEMET
T496B225K020CT612C
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 20V, 10% +Tol, 10% -Tol, 2.2uF, 1411
KEMET
T496B225K020CT621A
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 20V, 10% +Tol, 10% -Tol, 2.2uF, Surface Mount, 1411, CHIP, ROHS COMPLIANT
KEMET
T496B225K020CT631A
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 20V, 10% +Tol, 10% -Tol, 2.2uF, Surface Mount, 1411, CHIP, ROHS COMPLIANT
KEMET
T496B225K020CT631B
Tantalum Capacitor, Polarized, Tantalum (dry/solid), 20V, 10% +Tol, 10% -Tol, 2.2uF, Surface Mount, 1411, CHIP, ROHS COMPLIANT
KEMET
©2020 ICPDF网 联系我们和版权申明