T528I686M004AHE2007280

KEMET Organic Capacitor (KO-CAP)

T528 Low ESL/Facedown Terminal Polymer Tantalum

Overview

The KEMET Organic Capacitor (KO-CAP) is a tantalum

capacitor with a Ta anode and Ta₂O₅dielectric. A conductive

organic polymer replaces the traditionally used MnO₂as the

cathode plate of the capacitor. This results in very low ESR and

improved capacitance retention at high frequency. The KO-CAP

also exhibits a benign failure mode which eliminates the ignition

failures that can occur in standard MnO₂tantalum types. KO-

CAPs may also be operated at steady state voltages up to 90%

ofꢀratedꢀvoltageꢀforꢀpartꢀtypesꢀwithꢀratedꢀvoltagesꢀofꢀ≤ꢀ10ꢀvoltsꢀ

and up to 80% of rated voltage for part types > 10 volts with

equivalent or better reliability than traditional MnO₂tantalum

capacitors operated at 50% of rated voltage.

The T528 Series KO-CAP combines ultra-low ESR and high

capacitance in a package design that offers the lowest ESL in

the market for this type of product. This series offers exceptional

performance for high-speed server and microprocessor decoupling

– designs that are driving the demand for low inductance chips.

The T528 uses a different termination design that allows for a

reductionꢀinꢀtheꢀinductanceꢀloopꢀareaꢀandꢀcomesꢀinꢀaꢀlowꢀproﬁleꢀ

1.7 mm case height. These product features offer the advantage of

improved capacitance retention at frequencies of up to 1 MHz.

Beneﬁts

Applications

• Polymer cathode technology

• 100% accelerated steady state aging

• Low ESL <0.7 nH @ 20 MHz

• 100% surge current tested

Typical applications include high speed server, microprocessor

decoupling and high ripple current applications.

• High frequency capacitance retention

• Non-ignition failure mode

•ꢀ Improvedꢀvolumetricꢀefﬁciency

• Self-healing mechanism

• Capacitance: 33 µF to 470 µF

• Use up to 90% of rated voltage (10% derating)

• Voltage: 2 V to 10 V

• RoHS compliant and Halogen Free

• 105°C maximum temperature capability

•ꢀ Leadꢀfreeꢀ260°Cꢀreﬂowꢀcapable

Environmental Compliance

RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn Solder

One world. One KEMET

T2018_T528 • 9/6/2013

1

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

SPICE

Forꢀaꢀdetailedꢀanalysisꢀofꢀspeciﬁcꢀpartꢀnumbers,ꢀpleaseꢀvisitꢀwww.kemet.comꢀforꢀaꢀfreeꢀdownloadꢀofꢀKEMET'sꢀSPICEꢀsoftware.ꢀ

The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over

frequency, temperature, ripple, and DC bias conditions.

Ordering Information

T

528

Z

337

M

2R5

A

T

E009

Capacitor

Class

Capacitance

Code (pF)

Capacitance

Tolerance

Failure Rate/

Design

Packaging

(C-Spec)

Series

Case Size

Voltage

Lead Material

ESR Code

T =

528 =

B, I, K, W, Z

First two digits

represent

signiﬁcantꢀ

ﬁgures.ꢀThirdꢀdigitꢀ

speciﬁesꢀnumberꢀ

of zeros.

M = ±20%

002 = 2 V

2R5 = 2.5 V

003 = 3 V

004 = 4 V

006 = 6.3 V

010 = 10 V

A = N/A

T = 100%

Matte Tin (Sn) Last three digits

Plated

P = Ni-Pd-Au

Plated

E = ESR

Blank = 7"

Reel 7280 =

13" Reel

Tantalum Low ESL

Facedown

specify ESR in

mΩꢀ(009ꢀ=ꢀ9ꢀmΩ)

Terminal

Polymer

Performance Characteristics

Item

Performance Characteristics

Operating Temperature

Rated Capacitance Range

Capacitance Tolerance

Rated Voltage Range

DF (120 Hz)

-55°C to 105°C

33 – 470 µF @ 120 Hz/25°C

M Tolerance (20%)

2 – 10 V

≤ꢀ10%ꢀꢀ

ESR (100 kHz)

ReferꢀtoꢀPartꢀNumberꢀElectricalꢀSpeciﬁcationꢀTableꢀ

≤ꢀ0.1ꢀCVꢀ(µA)ꢀatꢀratedꢀvoltageꢀafterꢀ5ꢀminutes

Leakage Current

T2018_T528 • 9/6/2013

2

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Qualiﬁcation

Test

Condition

Characteristics

Within -20/+10% of initial value

≤ꢀInitialꢀLimit

ΔꢀC/C

DF

Endurance

Storage Life

Humidity

105°C @ rated voltage, 2,000 hours

DCL

ESR

ΔꢀC/C

DF

Within 1.25 x initial limit

Within 2.0 x initial limit

Within -20/+10% of initial value

Within initial limits

105°C @ 0 volts, 2,000 hours

60°C, 90% RH, 500 hours

DCL

ESR

ΔꢀC/C

DF

Within 1.25 x initial limit

Within 2.0 x initial limit

Within -5/+35% of initial value

≤ꢀInitialꢀLimit

DCL

ESR

+25°C

IL*

Within 5.0 x initial limit

Within 2.0 x initial limit

-55°C

±20%

IL

+85°C

±20%

+105°C

±30%

Extreme temperature exposure at a

succession of continuous steps at +25°C,

-55°C, +25°C, +85°C, +105°C, +25°C

ΔꢀC/C

DF

Temperature Stability

IL

1.2 x IL

10 x IL

1.5 x IL

10 x IL

DCL

IL

n/a

ΔꢀC/C

DF

Within -20/+10% of initial value

Within initial limits

Surge Voltage

105°C, 1.32 x rated voltage 1,000 cycles

DCL

ESR

ΔꢀC/C

DF

Within initial limits

Within ±10% of initial value

Within initial limits

MIL–STD–202, Method 213, Condition I, 100 G peak

MIL–STD–202, Method 204, Condition D, 10 Hz to 2,000 Hz,

20 G peak

Mechanical Shock/Vibration

DCL

Within initial limits

*IL = Initial limit

T2018_T528 • 9/6/2013

3

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Electrical Characteristics

Capacitance vs. Frequency

ESR vs. Frequency

10

1000

100

10

T528Z337M2R5ATE012_Imp

T528Z337M2R5ATE009_Imp

1

T528Z337M2R5ATE007_Imp

T528Z337M2R5ATE012_ESR

T528Z337M2R5ATE009_ESR

T528Z337M2R5ATE007_ESR

0.1

0.01

T528Z337M2R5ATE012

T528Z337M2R5ATE009

T528Z337M2R5ATE007

0.001

1

100

1,000

10,000

100,000

1,000,000

10,000,000

1,000

10,000

100,000

Frequency (Hz)

1,000,000

10,000,000

Frequency (Hz)

Dimensions – Millimeters

Case Size

Component

KEMET

EIA

L

W

H

F ±0.2

S1 ±0.2

S2 ±0.2

I

3216–10

3528–10

3528–20

7343–15

7343–17

3.2 ±0.2

3.5 ±0.3

3.5 ±0.2

7.3 ±0.4

1.6 ±0.2

2.8 ±0.3

2.8 ±0.2

4.3 ±0.3

1.0 Maximum

2.0 Maximum

1.5 Maximum

1.7 Maximum

1.2

2

1.0

1.2

0.8

5.1

0.7

0.6

0.8

1.3

K

B

W

Z

2.2

2.8

T2018_T528 • 9/6/2013

4

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Table 1 – Ratings & Part Number Reference

Maximum

Allowable

Ripple Current

Rated

Case Code/

KEMET Part

Number

DC

Leakage

Moisture

Sensitivity

DF

ESR

Voltage Capacitance Case Size

µA @ +20ºC

Maximum/

5 Minutes

% @ +20ºC

120 Hz

Maximum

mΩ @ +20ºC

100 kHz

Maximum

(See below for

part options)

VDC

µF

KEMET/EIA

(mA) +45ºC 100 kHz

Temp ≤ 260ºC

2

270

220

330

470

100

68

B/3528-21

Z/7343-18

W/7343-15

Z/7343-18

I/3216-10

K/3528-10

Z/7343-18

I/3216-10

K/3528-10

Z/7343-18

I/3216-10

T528B277M002APE006

T528B277M002APE009

T528Z227M2R5ATE006

T528W337M2R5ATE009

T528Z337M2R5ATE005

T528Z337M2R5ATE006

T528Z337M2R5ATE007

T528Z337M2R5ATE008

T528Z337M2R5ATE009

T528Z337M2R5ATE012

T528Z477M2R5ATE005

T528Z477M2R5ATE006

T528Z477M2R5ATE008

T528Z477M2R5ATE009

T528Z477M2R5ATE012

T528I107M003ATE150

T528I107M003ATE200

T528I686M004ATE150

T528I686M004ATE200

T528K227M004ATE100

T528Z227M004ATE007

T528Z227M004ATE008

T528Z227M004ATE009

T528Z227M004ATE012

T528Z337M004ATE009

T528Z337M004ATE012

T528I476M006ATE150

T528I476M006ATE200

T528K157M006ATE100

T528K157M006ATE200

T528Z157M006ATE007

T528Z157M006ATE008

T528Z157M006ATE009

T528Z157M006ATE012

T528Z227M006ATE009

T528Z227M006ATE012

T528I336M010ATE150

T528I336M010ATE200

54.0

55.0

82.5

117.5

30.0

27.2

8

6

9

6

9

5

6

7

8

9

12

5

6

8

9

12

150

200

150

200

100

7

8

9

12

9

12

150

200

100

200

7

3900

3200

7400

6000

8100

7400

6800

6400

6000

5200

8100

7400

6400

6000

5200

800

3

2.5

3

4

10

700

800

700

68

27.2

220

330

47

88.0

132.0

29.6

94.5

138.6

33.0

1200

6800

6400

6000

5200

6000

5200

800

700

1200

900

6800

6400

6000

5200

6000

5200

800

4

6.3

10

47

150

220

33

8

9

12

9

12

150

200

33

700

µA @ +20ºC

Maximum/

5 Minutes

% @ +20ºC

120 Hz

Maximum

mΩꢀ@ꢀ+20ºC

100 kHz

Maximum

(See below for

part options)

VDC

µF

KEMET/EIA

(mA) +45ºC 100 kHz

Temp ≤ 260ºC

Rated

Voltage

Rated

Capacitance

Case Code/

Case Size

DC

Leakage

Maximum Allowable

Ripple Current

Moisture

Sensitivity

KEMET Part Number

DF

ESR

Other part number options:

1- Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H).

Also available on large (13 inch) reels. Add 7280 to the end of the part number.

Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked

T

528

Z

337

M

2R5

A

T

E009

with the higher voltage rating. Substitutions can include better than series.

Capacitor

Class

Capacitance

Code (pF)

Capacitance

Tolerance

Failure Rate/

Design

Packaging

(C-Spec)

Bold text denotes black epoxy product

Series

Case Size

Voltage

Lead Material

ESR Code

T =

528 =

B, I, K, W, Z

First two digits

represent

signi ꢀcantꢀ

ꢀgures.ꢀThirdꢀdigitꢀ

speci ꢀesꢀnumberꢀ

of zeros.

M = ±20%

002 = 2 V

2R5 = 2.5 V

003 = 3 V

004 = 4 V

006 = 6.3 V

010 = 10 V

A = N/A

T = 100%

Matte Tin (Sn) Last three digits

Plated

P = Ni-Pd-Au

Plated

E = ESR

Blank = 7"

Reel 7280 =

13" Reel

Tantalum Low ESL

Facedown

specify ESR in

mΩꢀ(009ꢀ=ꢀ9ꢀmΩ)

Terminal

Polymer

T2018_T528 • 9/6/2013

5

Roll Over for

Order Info.

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Derating Guidelines

100%

Maximum

Transient

Voltage

95%

90%

85%

80%

75%

70%

65%

60%

55%

50%

Maximum

Recommended

Steady State

Voltage

Maximum

Recommended

Transient Voltage

(1 ms – 1 µs)

Recommended

Application

Voltage

Voltage Rating

-55°C to 105°C

2ꢀVꢀ≤ꢀV_Rꢀ≤ꢀ10ꢀV

90% of V_R

V_R

V_R= Rated Voltage

-55

25

85

105

Temperature (°C)

Ripple Current/Ripple Voltage

Permissible AC ripple voltage and current are related to equivalent

series resistance (ESR) and the power dissipation capabilities of

the device. Permissible AC ripple voltage which may be applied is

limited by two criteria:

1. The positive peak AC voltage plus the DC bias voltage, if any,

must not exceed the DC voltage rating of the capacitor.

2. The negative peak AC voltage in combination with bias

voltage,ꢀifꢀany,ꢀmustꢀnotꢀexceedꢀtheꢀallowableꢀlimitsꢀspeciﬁedꢀforꢀ

reverse voltage. See the Reverse Voltage section for allowable

limits.

The maximum power dissipation by case size can be determined

using the table at right. The maximum power dissipation rating

stated in the table must be reduced with increasing environmental

operating temperatures. Refer to the table below for temperature

compensation requirements.

Maximum Power

Dissipation (P max)

mWatts @ 45°C with

EIA

Case Code

+30°C Rise

I

3216-10

3528-10

3528-20

7343-15

7343-17

7343-31

7343-40

7443-43

96

K

B

W

Z

162

127

325

255

263

270

D

Y

X

The maximum power dissipation rating must be reduced with increasing

environmental operating temperatures. Refer to the Temperature

Compensation Multiplier table for details.

Temperature Compensation Multipliers

for Maximum Power Dissipation

Tꢀ≤ꢀ45°C

45°ꢀCꢀ<ꢀTꢀ≤ꢀ85°C

85°Cꢀ<ꢀTꢀ≤ꢀ125°C

1.00

0.70

0.25

T= Environmental Temperature

Using the P max of the device, the maximum allowable rms ripple

current or voltage may be determined.

I(max) = √P max/R

E(max) = Z √P max/R

I = rms ripple current (amperes)

E = rms ripple voltage (volts)

P max = maximum power dissipation (watts)

R = ESR at speciﬁed frequency (ohms)

Z = Impedance at speciﬁed frequency (ohms)

T2018_T528 • 9/6/2013

6

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Reverse Voltage

Polymer tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected in the wrong polarity.

These devices will withstand a small degree of transient voltage reversal for short periods as shown in the below table.

Temperature

Permissible Transient Reverse Voltage

25°C

55°C

15% of Rated Voltage

10% of Rated Voltage

5% of Rated Voltage

3% of Rated Voltage

1% of Rated Voltage

85°C

105°C

125°C*

*For Series Rated to 125°C

Table 2 – Land Dimensions/Courtyard

Metric

Size

Density Level A:

Maximum (Most)

Density Level B:

Median (Nominal)

Density Level C:

Minimum (Least)

KEMET

Code

Land Protrusion (mm)

Case

B

I¹

EIA

L1

L2

W

S1

S2 V1 V2

L1

L2

W

S1

S2 V1 V2

L1

L2

W

S1

S2 V1 V2

3528-20 2.20 2.20 2.35 0.46 0.46 6.32 4.00 1.80 1.80 2.23 0.56 0.56 5.22 3.50 1.42 1.42 2.13 0.64 0.64 4.36 3.24

3216-10 2.34 2.04 1.44 0.17 0.47 6.02 2.80 1.94 1.64 1.32 0.27 0.57 4.92 2.30 1.56 1.26 1.22 0.35 0.65 4.06 2.04

3258-10 2.62 2.02 2.24 0.09 0.69 6.42 4.10 2.22 1.62 2.12 0.19 0.79 5.32 3.60 1.84 1.24 2.02 0.27 0.87 4.46 3.34

7343-15 6.48 2.68 3.04 -1.82 1.98 10.32 5.60 6.18 2.38 2.92 -1.82 1.98 9.22 5.10 5.82 2.02 2.82 -1.76 2.04 8.36 4.84

7343-17 6.48 2.68 3.04 -1.82 1.98 10.32 5.60 6.18 2.38 2.92 -1.82 1.98 9.22 5.10 5.82 2.02 2.82 -1.76 2.04 8.36 4.84

K

W²

Z²

Density Level A: For low-density product applications. Recommended for wave solder

applications and provides a wider process window for reﬂow solder processes.

Density Level B: For products with a moderate level of component density. Provides a

robust solder attachment condition for reﬂow solder processes.

Density Level C: For high component desity product applications. Before adapting the

minimum land pattern variations the user should perform qualiﬁcation testing based on

the conditions outlined in IPC standard 7351 (IPC–7351).

¹ Land pattern geometry is too small for silkscreen outline.

²Negative values of S1 mean that pad lies at the center's right side.

T2018_T528 • 9/6/2013

7

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Soldering Process

KEMET’s families of surface mount capacitors are compatible

Proﬁle Feature

SnPb Assembly Pb-Free Assembly

withꢀwaveꢀ(singleꢀorꢀdual),ꢀconvection,ꢀIR,ꢀorꢀvaporꢀphaseꢀreﬂowꢀ

techniques. Preheating of these components is recommended

toꢀavoidꢀextremeꢀthermalꢀstress.ꢀKEMET'sꢀrecommendedꢀ

proﬁleꢀconditionsꢀforꢀconvectionꢀandꢀIRꢀreﬂowꢀreﬂectꢀtheꢀproﬁleꢀ

conditions of the IPC/J–STD–020D standard for moisture

sensitivity testing. The devices can safely withstand a maximum

ofꢀthreeꢀreﬂowꢀpassesꢀatꢀtheseꢀconditions.

Preheat/Soak

Temperature Minimum (T_Smin

)

100°C

150°C

200°C

Temperature Maximum (T_Smax

)

Time (t_s) from T_sminto T_smax

Ramp-up Rate (T_Lto T_P)

)

60 – 120 seconds

3°C/seconds maximum

183°C

60 – 120 seconds

3°C/seconds maximum

217°C

Liquidous Temperature (T_L)

Time Above Liquidous (t_L)

60 – 150 seconds

220°C*

235°C**

250°C*

260°C**

Peak Temperature (T_P)

Please note that although the X/7343–43 case size can withstand

waveꢀsoldering,ꢀtheꢀtallꢀproﬁleꢀ(4.3ꢀmmꢀmaximum)ꢀdictatesꢀcareꢀinꢀ

wave process development.

Time within 5°C of Maximum

Peak Temperature (t_P)

20 seconds maximum

6°C/seconds maximum

6 minutes maximum

30 seconds maximum

6°C/seconds maximum

8 minutes maximum

Ramp-down Rate (T_Pto T_L)

Time 25°C to Peak

Temperature

Handꢀsolderingꢀshouldꢀbeꢀperformedꢀwithꢀcareꢀdueꢀtoꢀtheꢀdifﬁcultyꢀ

in process control. If performed, care should be taken to avoid

contact of the soldering iron to the molded case. The iron should

be used to heat the solder pad, applying solder between the pad

andꢀtheꢀtermination,ꢀuntilꢀreﬂowꢀoccurs.ꢀOnceꢀreﬂowꢀoccurs,ꢀtheꢀ

iron should be removed immediately. “Wiping” the edges of a chip

and heating the top surface is not recommended.

Note: All temperatures refer to the center of the package, measured on the

package body surface that is facing up during assembly reﬂow.

*Case Size D, E, P, Y, and X

**Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z

T_P

t_P

Maximum Ramp Up Rate = 3ºC/seconds

Maximum Ramp Down Rate = 6ºC/seconds

T_L

t_L

Duringꢀtypicalꢀreﬂowꢀoperations,ꢀaꢀslightꢀdarkeningꢀofꢀtheꢀgold-

colored epoxy may be observed. This slight darkening is normal

and not harmful to the product. Marking permanency is not

affected by this change.

T

smax

T

smin

t_S

25

25ºC to Peak

Time

Construction

Epoxy

Tantalum

Washer

Tantalum

Wire

Weld

Leadframe

(-Cathode)

Polymer

Silver Paint

Leadframe

Carbon

(+Anode)

Ta₂O₅

T2018_T528 • 9/6/2013

8

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Capacitor Marking

(FDO)

Facedown

Organic

Polarity

Indicator (+)

FD

Polymer

Picofarad Code

KEMET ID

337

2R5 K

230

Rated

Voltage

Date

Code*

* 230 = 30^thweek of 2012

Date Code *

1^stdigit = Last number of Year

9 = 2009

0 = 2010

1 =2011

2 = 2012

3 = 2013

4 =2014

2^ndand 3^rddigit = Week of the Year

01 = 1^stweek of the Year to

52 = 52^ndweek of the Year

Storage

All KO-CAPꢀseriesꢀareꢀshippedꢀinꢀmoistureꢀbarrierꢀbagsꢀwithꢀaꢀdesiccantꢀandꢀmoistureꢀindicatorꢀcard.ꢀTheseꢀseriesꢀareꢀclassiﬁedꢀ

as MSL3 (Moisture Sensitivity Level 3). Product contained within the moisture barrier bags should be stored in normal working

environments with temperatures not to exceed 40°C and humidity not in excess of 60% RH.

T2018_T528 • 9/6/2013

9

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Tape & Reel Packaging Information

KEMET’s molded tantalum and aluminum chip capacitor families are packaged in 8 and 12 mm plastic tape on 7" and 13" reels in

accordance with EIA Standard 481–1: Embossed Carrier Taping of Surface Mount Components for Automatic Handling. This packaging

system is compatible with all tape-fed automatic pick-and-place systems.

8 mm (0.315")

or

12 mm (0.472")

180 mm (7.0")

Top Tape Thickness

or

0.10 mm (0.004")

330 mm (13.0")

Maximum Thickness

Table 3 – Packaging Quantity

Tape Width

Case Code

7" Reel*

13" Reel*

(mm)

KEMET

EIA

I

S

T

M

U

L

W

Z

V

A

B

C

D

Y

3216-10

3216-12

3528-12

3528-15

6032-15

6032-19

7343-15

7343-17

7343-20

3216-18

3528-21

6032-28

7343-31

7343-40

7343-43

7360-38

7360-20

8

12

8

3,000

2,500

2,000

1,000

2,000

500

12,000

10,000

8,000

5,000

3,000

9,000

8,000

3,000

2,500

2,000

2,500

8

12

500

X

E/T428P

H

1,000

* No C-Spec required for 7" reel packaging. C-7280 required for 13" reel packaging.

T2018_T528 • 9/6/2013 10

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Figure 1 – Embossed (Plastic) Carrier Tape Dimensions

T

P2

[10 pitches cumulative

tolerance on tape ± 0.2 mm]

2

E

1

Po

ØDo

Ao

F

Ko

W

E

2

B

1

Bo

S

1

P

1

T

1

Embossment

For cavity size,

see Note 1 Table 4

Center Lines of Cavity

ØD

1

Cover Tape

is for tape feeder reference only,

including draft concentric about B

B

1

o

.

User Direction of Unreeling

Table 4 – Embossed (Plastic) Carrier Tape Dimensions

Metric will govern

Constant Dimensions — Millimeters (Inches)

D₁Minimum

Note 1

1.0

R Reference S₁Minimum

Tape Size

8 mm

D₀

E₁

P₀

P₂

T Maximum T₁Maximum

Note 2

Note 3

25.0

(0.984)

(0.039)

1.5 +0.10/-0.0

(0.059 +0.004/-0.0)

1.75 ±0.10

4.0 ±0.10

2.0 ±0.05

0.600

(0.024)

0.600

(0.024)

0.100

(0.004)

12 mm

16 mm

(0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002)

1.5

(0.059)

30

(1.181)

Variable Dimensions — Millimeters (Inches)

B₁Maximum

Note 4

4.35

(0.171)

8.2

(0.323)

12.1

(0.476)

Tape Size

8 mm

Pitch

E₂Minimum

F

P₁

T₂Maximum W Maximum

A₀,B₀& K₀

6.25

(0.246)

10.25

(0.404)

14.25

3.5 ±0.05

4.0 ±0.10

2.5

(0.098)

4.6

8.3

(0.327)

12.3

Single (4 mm)

(0.138 ±0.002) (0.157 ±0.004)

5.5 ±0.05 8.0 ±0.10

(0.217 ±0.002) (0.315 ±0.004)

5.5 ±0.05 8.0 ±0.10

(0.217 ±0.002) (0.315 ±0.004)

Single (4 mm) &

Double (8 mm)

12 mm

16 mm

Note 5

(0.181)

4.6

(0.484)

16.3

Triple (12 mm)

(0.561)

(0.181)

(0.642)

1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and

hole location shall be applied independent of each other.

2. The tape, with or without components, shall pass around R without damage (see Figure 5).

3. If S₁< 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481–D, paragraph 4.3, section b).

4. B₁dimension is a reference dimension for tape feeder clearance only.

5. The cavity deﬁned by A₀, B₀and K₀shall surround the component with sufﬁcient clearance that:

(a) the component does not protrude above the top surface of the carrier tape.

(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.

(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 2).

(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 3).

(e) see Addendum in EIA Standard 481–D for standards relating to more precise taping requirements.

T2018_T528 • 9/6/2013 11

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Packaging Information Performance Notes

1. Cover Tape Break Force: 1.0 Kg minimum.

2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:

Tape Width

8 mm

Peel Strength

0.1 to 1.0 Newton (10 to 100 gf)

0.1 to 1.3 Newton (10 to 130 gf)

12 and 16 mm

The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180°

from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute.

3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA

Standards 556 and 624.

Figure 2 – Maximum Component Rotation

°

T

Maximum Component Rotation

Top View

Maximum Component Rotation

Side View

Typical Pocket Centerline

Tape

Maximum

°

T

s

Width (mm) Rotation (

)

8,12

16 – 200

20

10

Bo

Tape

Maximum

°

S

Width (mm) Rotation (

)

8,12

16 – 56

72 – 200

20

10

5

Typical Component Centerline

Ao

Figure 4 – Bending Radius

Figure 3 – Maximum Lateral Movement

Embossed

Carrier

Punched

Carrier

8 mm & 12 mm Tape

16 mm Tape

0.5 mm maximum

1.0 mm maximum

R

Bending

Radius

R

T2018_T528 • 9/6/2013 12

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Figure 5 – Reel Dimensions

Full Radius,

W3 (Includes

flange distortion

at outer edge)

Access Hole at

Slot Location

(Ø 40 mm minimum)

See Note

W

2 (Measured at hub)

D

(See Note)

A

N

C

(Arbor hole

W

1 (Measured at hub)

diameter)

If present,

tape slot in core

for tape start:

2.5 mm minimum width x

10.0 mm minimum depth

B

(see Note)

Note: Drive spokes optional; if used, dimensions B and D shall apply.

Table 5 – Reel Dimensions

Metric will govern

Constant Dimensions — Millimeters (Inches)

Tape Size

8 mm

A

B Minimum

C

D Minimum

178 ±0.20

(7.008 ±0.008)

or

330 ±0.20

(13.000 ±0.008)

1.5

(0.059)

13.0 +0.5/-0.2

(0.521 +0.02/-0.008)

20.2

(0.795)

12 mm

16 mm

Variable Dimensions — Millimeters (Inches)

Tape Size

8 mm

N Minimum

W₁

W₂Maximum

W₃

8.4 +1.5/-0.0

(0.331 +0.059/-0.0)

12.4 +2.0/-0.0

(0.488 +0.078/-0.0)

16.4 +2.0/-0.0

14.4

(0.567)

18.4

(0.724)

22.4

50

(1.969)

Shall accommodate tape width

without interference

12 mm

16 mm

(0.646 +0.078/-0.0)

(0.882)

T2018_T528 • 9/6/2013 13

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Figure 6 – Tape Leader & Trailer Dimensions

Embossed Carrier

Carrier Tape

Round Sprocket Holes

Punched Carrier

8 mm & 12 mm only

START

END

Top Cover Tape

Elongated Sprocket Holes

(32 mm tape and wider)

100 mm

Minimum Leader

400 mm Minimum

Trailer

160 mm Minimum

Components

Top Cover Tape

Figure 7 – Maximum Camber

Elongated sprocket holes

(32 mm & wider tapes)

Carrier Tape

Round Sprocket Holes

1 mm Maximum, either direction

Straight Edge

250 mm

T2018_T528 • 9/6/2013 14

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

KEMET Corporation

World Headquarters

Europe

Asia

Southern Europe

Paris, France

Tel: 33-1-4646-1006

Northeast Asia

Hong Kong

Tel: 852-2305-1168

2835 KEMET Way

Simpsonville, SC 29681

Sasso Marconi, Italy

Tel: 39-051-939111

Shenzhen, China

Tel: 86-755-2518-1306

Mailing Address:

P.O. Box 5928

Greenville, SC 29606

Beijing, China

Central Europe

Landsberg, Germany

Tel: 49-8191-3350800

Tel: 86-10-5829-1711

www.kemet.com

Tel: 864-963-6300

Fax: 864-963-6521

Shanghai, China

Tel: 86-21-6447-0707

Kamen, Germany

Tel: 49-2307-438110

Corporate Ofﬁces

Fort Lauderdale, FL

Tel: 954-766-2800

Taipei, Taiwan

Tel: 886-2-27528585

Northern Europe

Bishop’s Stortford, United Kingdom

Tel: 44-1279-460122

North America

Southeast Asia

Singapore

Southeast

Tel: 65-6586-1900

Lake Mary, FL

Tel: 407-855-8886

Espoo, Finland

Tel: 358-9-5406-5000

Penang, Malaysia

Tel: 60-4-6430200

Northeast

Wilmington, MA

Tel: 978-658-1663

Bangalore, India

Tel: 91-806-53-76817

Central

Novi, MI

Tel: 248-994-1030

West

Milpitas, CA

Tel: 408-433-9950

Mexico

Guadalajara, Jalisco

Tel: 52-33-3123-2141

Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not

assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of

KEMET Electronics Corporation.

T2018_T528 • 9/6/2013 15

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Other KEMET Resources

Tools

Resource

Location

Con ꢀgureꢀAꢀPart:ꢀCapEdge

SPICE & FIT Software

http://capacitoredge.kemet.com

http://www.kemet.com/spice

http://www.kemet.com/keask

http://www.kemet.com:8080/elc

Search Our FAQs: KnowledgeEdge

Electrolytic LifeCalculator

Product Information

Resource

Location

Products

Technical Resources (Including Soldering Techniques)

RoHS Statement

http://www.kemet.com/products

http://www.kemet.com/technicalpapers

http://www.kemet.com/rohs

Quality Documents

http://www.kemet.com/qualitydocuments

Product Request

Resource

Location

http://www.kemet.com/sample

http://www.kemet.com/kits

Sample Request

Engineering Kit Request

Contact

Location

Website

Contact Us

Investor Relations

Call Us

www.kemet.com

http://www.kemet.com/contact

http://www.kemet.com/ir

1-877-MyKEMET

Twitter

http://twitter.com/kemetcapacitors

Disclaimer

Allꢀproductꢀspeci ꢀcations,ꢀstatements,ꢀinformationꢀandꢀdataꢀ(collectively,ꢀtheꢀ“Information”)ꢀinꢀthisꢀdatasheetꢀareꢀsubjectꢀtoꢀchange.ꢀTheꢀcustomerꢀisꢀresponsibleꢀforꢀcheckingꢀandꢀ

verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.

All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.

Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are

notꢀintendedꢀtoꢀconstituteꢀ–ꢀandꢀKEMETꢀspeci ꢀcallyꢀdisclaimsꢀ–ꢀanyꢀwarrantyꢀconcerningꢀsuitabilityꢀforꢀaꢀspeci ꢀcꢀcustomerꢀapplicationꢀorꢀuse.ꢀTheꢀInformationꢀisꢀintendedꢀforꢀuseꢀonlyꢀ

by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise

provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.

Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still

occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective

circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.

Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not

be required.

T2018_T528 • 9/6/2013 16

KEMET Organic Capacitor (KO-CAP) – T528 Low ESL/Facedown Terminal Polymer Tantalum

Digitally signed by Jeannette Calvo

DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corp., ou=Marketing

Communications, cn=Jeannette Calvo, email=jeannettecalvo@kemet.com

Date: 2013.09.06 13:01:48 -04'00'

T2018_T528 • 9/6/2013 17


型号：	T528I686M004AHE2007280
厂家：	KEMET CORPORATION
描述：	CAPACITOR, TANTALUM, SOLID 电容器
文件：	总17页 (文件大小：1134K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

T528I686M004AHE2007280 [KEMET]

相关型号：

T528I686M004ATE150

T528I686M004ATE200

T528I686M004ATE2007280

T528K157M006ATE150

T528K157M006ATE200

T528M107M010ATE150

T528M107M010ATE200

T528M157M006ATE150

T528M157M006ATE200

T528M227M004ATE150

T528M227M004ATE200

T528M337M003ATE150