T530D687M2R5TE007 [KEMET]
Tantalum Capacitor, Polarized, Tantalum (solid Polymer), 2.5V, 20% +Tol, 20% -Tol, 680uF, 2917;型号: | T530D687M2R5TE007 |
厂家: | KEMET CORPORATION |
描述: | Tantalum Capacitor, Polarized, Tantalum (solid Polymer), 2.5V, 20% +Tol, 20% -Tol, 680uF, 2917 电容器 |
文件: | 总18页 (文件大小:1605K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
KEMET Organic Capacitor (KO-CAP)
T530 High Capacitance/125°C Rated Polymer Tantalum
Overview
The KEMET Organic Capacitor (KO-CAP) is a tantalum
capacitor with a Ta anode and Ta2O5 dielectric. A conductive
organic polymer replaces the traditionally used MnO2 as the
cathode plate of the capacitor. This results in very low ESR and
improved capacitance retention at high frequency. The KO-
CAP also exhibits a benign failure mode which eliminates the
ignition failures that can occur in standard MnO2 tantalum types.
KO-CAPs may also be operated at steady state voltages up to
90% of rated voltage for part types with rated voltages of ≤10
volts and up to 80% of rated voltage for part types >10 volts with
equivalent or better reliability than traditional MnO2 tantalum
capacitors operated at 50% of rated voltage.
The T530 Series KO-CAP offers the same advantages as
the T520 Series but also has the added advantages of higher
capacitance, 125°C performance capability, higher ripple current
handling capability and a lower ESR range. Packaged as multiple
anodes to reduce the depth that the signal must penetrate, this
parallel arrangement reduces the ESR further still to achieve the
highest capacitance and lowest ESR of any other type of surface
mount capacitor with typical ESR values as low as 4 mΩ. With
reduced ESR, the enhanced capacitance retention at higher
frequencies provides the lowest total capacitance and most
economical solution for high power applications.
Benefits
Applications
• ESR: 4 mΩ to 40 mΩ
• 125°C maximum operating temperature
• Polymer cathode technology
Typical applications include high speed server, microprocessor
decoupling and high ripple current applications.
• High frequency capacitance retention
• Non-ignition failure mode
• Capacitance: 150 µF to 1,500 µF
• 100% accelerated steady state aging
• 100% surge current tested
• Utilizes multiple tantalum anode technology
• Volumetric efficiency
• Use up to 90% of rated voltage (10% derating) for part types ≤ 10 V
• Use up to 80% of rated voltage (20% derating) for part types > 10 V
• Self-healing mechanism
• EIA standard case sizes
Environmental Compliance
RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn Solder
One world. One KEMET
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013
1
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
SPICE
For a detailed analysis of specific part numbers, please visit www.kemet.com for a free download of KEMET's SPICE software.
The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over
frequency, temperature, ripple, and DC bias conditions.
Ordering Information
T
530
X
337
M
010
A
T
E005
Capacitor
Class
Capacitance
Code (pF)
Capacitance
Tolerance
Failure Rate/
Design
Packaging
(C-Spec)
Series
Case Size
D, X, Y
Voltage
Lead Material
ESR Code
T =
530 = High
First two digits
represent significant
figures. Third digit
specifies number of
zeros.
M = ±20%
2R5 = 2.5 V
003 = 3 V
004 = 4 V
006 = 6.3 V
010 = 10 V
016 = 16 V
A = N/A
T = 100% Matte E = ESR Last Blank = 7"
Tantalum Capacitance
125°C Rated
Tin (Sn) Plated
H = Tin/Lead
(SnPb) Solder
Coated (5% Pb
minimum)
three digits
Reel
specify ESR 7280 = 13"
in mΩ (005 = Reel
5 mΩ )
Polymer
G = Gold Plated
Performance Characteristics
Item
Performance Characteristics
Operating Temperature
Rated Capacitance Range
Capacitance Tolerance
Rated Voltage Range
DF (120 Hz)
-55°C to 125°C
150 – 1,500 µF @ 120 Hz/25°C
M Tolerance (20%)
2.5 – 16 V
8%
ESR (100 kHz)
Refer to Part Number Electrical Specification Table
≤ 0.1 CV (µA) at rated voltage after 5 minutes
Leakage Current
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013
2
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Qualification
Test
Condition
Characteristics
Within -20%/+10% of initial value
≤ initial limit
Δ C/C
DF
105°C @ rated voltage, 2,000 hours
125°C @ 2/3 rated voltage, 2,000 hours
Endurance
DCL
ESR
Δ C/C
DF
2 x initial limit @ 125ºC
2 x initial limit
Within -20%/+10% of initial value
Within initial limits
Storage Life
Humidity
125°C @ 0 volts, 2,000 hours
DCL
ESR
Δ C/C
DF
Within 2.0 x initial limit
Within 2.0 x initial limit
Within -5%/+35% of initial value
≤ initial limit
60°C, 90% RH, 1,000 hours, No Load
DCL
+25°C
IL*
Within 3.0 x initial limit
-55°C
±20%
IL
+85°C
±20%
+125°C
±30%
Extreme temperature exposure at a
succession of continuous steps at +25ºC,
-55ºC, +25ºC, +85ºC, +105ºC, +25ºC
Δ C/C
DF
Temperature Stability
IL
1.2 x IL
10 x IL
1.5 x IL
10 x IL
DCL
IL
n/a
Δ C/C
DF
Within -20%/+10% of initial value
Within initial limits
Surge Voltage
105°C, 1.32 x rated voltage, 33Ω Resistance, 1,000 cycles
DCL
ESR
Δ C/C
DF
Within initial limits
Within initial limits
Within ±10% of initial value
Within initial limits
MIL–STD–202, Method 213, Condition I, 100 G peak
MIL–STD–202, Method 204, Condition D, 10 Hz to 2,000 Hz,
20 G peak
Mechanical Shock/Vibration
DCL
Within initial limits
*IL = Initial limit
Certification
DSCC Drawing 04052
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013
3
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Electrical Characteristics
Capacitance vs. Frequency
ESR vs. Frequency
10
1
1,000
100
10
T530D227M006ATE006_Imp
T530Y337M006ATE005_Imp
T530X477M006ATE004_Imp
T530D227M006ATE006_ESR
T530Y337M006ATE005_ESR
T530X477M006ATE004_ESR
0.1
T530D227M006ATE006
T530Y337M006ATE005
T530X477M006ATE004
0.01
1
0.001
100
1,000
10,000
Frequency (Hz)
100,000
1,000,000 10,000,000
100
1,000
10,000
100,000
1,000,000
10,000,000
Frequency (Hz)
Dimensions – Millimeters (Inches)
Metric will govern
Termination
cutout at
KEMET’s
option,
either end
Case Size
Component
F* ±0.1 S* ±0.3 B* ±0.15
±(.004) ±(.012) (Ref) ±.006
KEMET EIA
L*
W*
H*
X (Ref)
P (Ref) R (Ref) T (Ref) A (Min) G (Ref) E (Ref)
7.3 ±0.3
4.3 ±0.3
2.8 ±0.3
0.10 ± 0.10
(.004 ± .004)
0.10 ± 0.10
(.004 ± .004)
0.10 ± 0.10
(.004 ± .004)
7343–31
2.4 (.094) 1.3 (.051)
2.4 (.094) 1.3 (.051)
2.4 (.094) 1.3 (.051)
0.5 (.020)
0.5 (.020)
0.5 (.020)
0.9 (.035)
1.7 (.067)
1.7 (.067)
1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138)
1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138)
1.0 (.039) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138)
D
(0.287 ±0.012) (0.169 ±0.012) (0.110 ±0.012)
7.3 ±0.3 4.3 ±0.3 4.3 ±0.3
(0.287 ±0.012) (0.169 ±0.012) (0.157 ±0.012)
7.3 ±0.3 4.3 ±0.3
(0.287 ±0.012) (0.169 ±0.012)
7343–43
X
7343–40
4.0 (0.157)
Y
Notes: (Ref) – Dimensions provided for reference only. No dimensions are provided for B, P or R because low profile cases do not have a bevel or a notch.
* MIL–PRF–55365/8 specified dimensions
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013
4
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Table 1 – Ratings & Part Number Reference
Maximum
Allowable
Ripple Current
Rated
Voltage
Rated Case Code/
KEMET Part
Number
DC
Leakage
Moisture
Sensitivity
Rated
Temp
DF
ESR
Cap
Case Size
µA @ +20°C
Maximum/
5 Minutes
% @ +20°C mΩ @ +20°C
120 Hz
Maximum
(See below for
part options)
Temperature
≤ 260ºC
VDC
µF
KEMET/EIA
100 kHz
Maximum
(mA) +45°C 100 kHz
(ºC)
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
470
470
470
560
680
680
680
680
680
D/7343-31
D/7343-31
D/7343-31
D/7343-31
Y/7343-40
Y/7343-40
Y/7343-40
D/7343-31
D/7343-31
D/7343-31
X/7343-43
Y/7343-40
Y/7343-40
X/7343-43
X/7343-43
X/7343-43
X/7343-43
T530D477M2R5A(1)E005
T530D477M2R5A(1)E006
T530D477M2R5A(1)E010
T530D567M2R5A(1)E005
T530Y687M2R5A(1)E005
T530Y687M2R5A(1)E006
T530Y687M2R5(1)E007
T530D687M2R5A(1)E006
T530D687M2R5A(1)E010
T530D687M2R5(1)E007
T530X687M2R5A(1)E006
T530Y108M2R5A(1)E005
T530Y108M2R5A(1)E006
T530X108M2R5A(1)E004
T530X108M2R5A(1)E005
T530X108M2R5A(1)E006
T530X158M2R5A(1)E005
118
118
118
140
170
170
170
170
170
170
170
250
250
250
250
250
375
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
5
6
10
5
5
6
7
6
10
7
6
5
6
4
5
6
5
7100
6500
5000
7100
7300
6600
6100
6500
5000
6000
6700
7300
6600
8200
7300
6700
7300
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
125
680
680
1000
1000
1000
1000
1000
1500
3
3
3
3
470
680
1000
1500
D/7343-31
D/7343-31
X/7343-43
X/7343-43
T530D477M003A(1)E010
T530D687M003A(1)E010
T530X108M003A(1)E010
T530X158M003A(1)E008
141
204
300
450
8
8
8
8
10
10
10
8
5000
5000
5200
5800
3
3
3
3
125
125
125
125
4
4
4
4
4
4
4
4
4
4
4
4
330
330
470
470
470
470
680
680
680
680
680
1000
D/7343-31
D/7343-31
D/7343-31
D/7343-31
Y/7343-40
Y/7343-40
Y/7343-40
X/7343-43
X/7343-43
X/7343-43
X/7343-43
X/7343-43
T530D337M004A(1)E005
T530D337M004A(1)E006
T530D477M004A(1)E006
T530D477M004A(1)E010
T530Y477M004A(1)E005
T530Y477M004A(1)E006
T530Y687M004A(1)E005
T530X687M004A(1)E004
T530X687M004A(1)E005
T530X687M004A(1)E006
T530X687M004A(1)E010
T530X108M004A(1)E006
132
132
188
188
188
188
272
272
272
272
272
400
8
8
8
8
8
8
8
8
8
8
8
8
5
6
6
10
5
6
5
4
5
6
7100
6500
6500
5000
7300
6600
7300
8200
7300
6700
5200
6700
3
3
3
3
3
3
3
3
3
3
3
3
125
125
125
125
125
125
125
125
125
125
125
125
10
6
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
6.3
220
220
330
330
330
330
330
470
470
D/7343-31
D/7343-31
D/7343-31
D/7343-31
Y/7343-40
Y/7343-40
Y/7343-40
Y/7343-40
X/7343-43
T530D227M006A(1)E005
T530D227M006A(1)E006
T530D337M006A(1)E006
T530D337M006A(1)E010
T530Y337M006A(1)E005
T530Y337M006A(1)E006
T530Y337M006A(1)E010
T530Y477M006A(1)E005
T530X477M006A(1)E004
139
139
208
208
208
208
208
296
296
8
8
8
8
8
8
8
8
8
5
6
6
10
5
6
10
5
4
7100
6500
6500
5000
7300
6600
5100
7300
8200
3
3
3
3
3
3
3
3
3
125
125
125
125
125
125
125
125
125
010
A
T
530
X
337
M
T
E005
Capacitor
Class
Capacitance
Code (pF)
Capacitance
Failure Rate/
Packaging
ESR Code
Series
Case Size
Voltage
Lead Material
Tolerance
Design
(C-Spec)
T =
530 = High
D, X, Y
First two digits
M = ±20%
2R5 = 2.5 V
003 = 3 V
004 = 4 V
006 = 6.3 V
010 = 10 V
A = N/A
T = 100% Matte E = ESR Last Blank = 7"
Tantalum Capacitance
represent significant
Tin (Sn) Plated
three digits
specify ESR 7280 = 13"
Reel
125°C Rated
Polymer
figures. Third digit
specifies number of
zeros.
H = Tin/Lead
(SnPb) Solder
Coated (5% Pb
minimum)
G = Gold Plated
in mΩ (005 = Reel
5 mΩ )
O
(
A
016 = 16 V
H
w
©
Roll Over for
Order Info.
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Table 1 – Ratings & Part Number Reference cont'd
Maximum
Allowable
Ripple Current
Rated
Voltage
Rated Case Code/
KEMET Part
Number
DC
Leakage
Moisture
Sensitivity
Rated
Temp
DF
ESR
Cap
Case Size
µA @ +20°C
Maximum/
5 Minutes
% @ +20°C mΩ @ +20°C
120 Hz
Maximum
(See below for
part options)
Temperature
≤ 260ºC
VDC
µF
KEMET/EIA
100 kHz
Maximum
(mA) +45°C 100 kHz
(ºC)
6.3
680
X/7343-43
T530X687M006A(1)E018
428
8
18
3900
3
125
10
10
10
10
10
10
10
10
10
10
150
150
150
220
220
220
330
330
330
330
D/7343-31
D/7343-31
D/7343-31
D/7343-31
D/7343-31
Y/7343-40
X/7343-43
X/7343-43
X/7343-43
X/7343-43
T530D157M010A(1)E005
T530D157M010A(1)E006
T530D157M010A(1)E010
T530D227M010A(1)E006
T530D227M010A(1)E010
T530Y227M010A(1)E006
T530X337M010A(1)E004
T530X337M010A(1)E005
T530X337M010A(1)E006
T530X337M010A(1)E010
150
150
150
220
220
220
330
330
330
330
8
8
8
8
8
8
8
8
8
8
5
6
10
6
10
6
4
5
6
10
7100
6500
5000
6500
5000
6600
8200
7300
6700
5200
3
3
3
3
3
3
3
3
3
3
125
125
125
125
125
125
125
125
125
125
16
16
16
150
150
150
X/7343-43
X/7343-43
X/7343-43
T530X157M016A(1)E015
T530X157M016A(1)E025
T530X157M016A(1)E040
240
240
240
8
8
8
15
25
40
4200
3300
2600
3
3
3
125
125
125
µA @ +20°C
Maximum/
5 Minutes
% @ +20°C mΩ @ +20°C
(See below for
part options)
Temperature
≤ 260ºC
VDC
µF
KEMET/EIA
120 Hz
100 kHz
(mA) +45°C 100 kHz
(ºC)
Maximum
Maximum
Maximum
Allowable
Ripple Current
Rated
Voltage
Rated
Cap
Case Code/
Case Size
KEMET Part
Number
DC
Leakage
Moisture
Sensitivity
Rated
Temp
DF
ESR
Other part number options:
(1) Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H).
Also available on large (13 inch) reels. Add 7280 to the end of the part number.
Higher voltage ratings and tighter tolerance product including ESR may be substituted within the same size at KEMET's option. Voltage substitutions will be marked
with the higher voltage rating. Substitutions can include better than series.
T
530
X
337
M
010
A
T
E005
Capacitor
Class
Capacitance
Code (pF)
Capacitance
Tolerance
Failure Rate/
Design
Packaging
(C-Spec)
Series
Case Size
D, X, Y
Voltage
Lead Material
ESR Code
T =
530 = High
First two digits
represent significant
figures. Third digit
specifies number of
zeros.
M = ±20%
2R5 = 2.5 V
003 = 3 V
004 = 4 V
006 = 6.3 V
010 = 10 V
016 = 16 V
A = N/A
T = 100% Matte E = ESR Last Blank = 7"
Tantalum Capacitance
125°C Rated
Tin (Sn) Plated
H = Tin/Lead
(SnPb) Solder
Coated (5% Pb
minimum)
three digits
Reel
specify ESR 7280 = 13"
in mΩ (005 = Reel
5 mΩ )
Polymer
G = Gold Plated
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013
6
Roll Over for
Order Info.
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Derating Guidelines
100%
95%
90%
85%
80%
75%
70%
65%
60%
55%
50%
Maximum
Recommended Steady
State Voltage
Maximum Transient Voltage
Voltage
Rating
Maximum Recommended
Transient Voltage (1 ms – 1 µs)
Recommended Application Voltage VR ≤ 10 V
Recommended Application Voltage VR > 10 V
-55°C to 105°C
67%
60%
54%
2.5 V ≤ VR ≤ 10 V
VR = 16V
90% of VR
80% of VR
VR
VR
105°C to 125°C
-55
25
45
85
105
125
2.5 V ≤ VR ≤ 10 V
VR = 16 V
60% of VR
54% of VR
67% of VR
67% of VR
Temperature (ºC)
VR = Rated Voltage
Ripple Current/Ripple Voltage
Permissible AC ripple voltage and current are related to equivalent
series resistance (ESR) and the power dissipation capabilities of
the device. Permissible AC ripple voltage which may be applied is
limited by two criteria:
1. The positive peak AC voltage plus the DC bias voltage, if any,
must not exceed the DC voltage rating of the capacitor.
2. The negative peak AC voltage in combination with bias
voltage, if any, must not exceed the allowable limits specified for
reverse voltage. See the Reverse Voltage section for allowable
limits.
The maximum power dissipation by case size can be determined
using the table at right. The maximum power dissipation rating
stated in the table must be reduced with increasing environmental
operating temperatures. Refer to the table below for temperature
compensation requirements.
Maximum Power
Dissipation (P max)
mWatts @ 45°C with
EIA
Case Code
Case Code
+30°C Rise
W
Z
7343-15
7343-17
7343-31
7343-40
7443-43
325
325
255
263
270
D
Y
X
The maximum power dissipation rating must be reduced with increasing
environmental operating temperatures. Refer to the Temperature
Compensation Multiplier table for details.
Temperature Compensation Multipliers
for Maximum Power Dissipation
≤ 45°C
45° C < T ≤ 85°C
85°C < T ≤ 125°C
1.00
0.70
0.25
T= Environmental Temperature
Using the P max of the device, the maximum allowable rms ripple
current or voltage may be determined.
I(max) = √P max/R
E(max) = √P max*R
I = rms ripple current (amperes)
E = rms ripple voltage (volts)
P max = maximum power dissipation (watts)
R = ESR at specified frequency (ohms)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013
7
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Reverse Voltage
Polymer tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected in the wrong polarity.
These devices will withstand a small degree of transient voltage reversal for short periods as shown in the below table.
Temperature
Permissible Transient Reverse Voltage
25°C
55°C
15% of Rated Voltage
10% of Rated Voltage
5% of Rated Voltage
3% of Rated Voltage
1% of Rated Voltage
85°C
105°C
125°C*
*For series rated to 125°C
Table 2 – Land Dimensions/Courtyard
Metric
Size
Code
Density Level A:
Maximum (Most) Land
Protrusion (mm)
Density Level B:
Median (Nominal) Land
Protrusion (mm)
Density Level C:
Minimum (Least) Land
Protrusion (mm)
KEMET
Case
EIA
X
Y
C
V1
V2
X
Y
C
V1
V2
X
Y
C
V1
V2
D
7343–31
2.55
3.75
2.70
10.20
5.50
2.45
3.35
2.60
9.10
5.00
2.35
2.95
2.50
8.20
4.70
X¹
Y¹
7343–43
7343–40
2.55
2.55
3.75
3.75
2.70
2.70
10.20
10.20
5.50
5.50
2.45
2.45
3.35
3.35
2.60
2.60
9.10
9.10
5.00
5.00
2.35
2.35
2.95
2.95
2.50
2.50
8.20
8.20
4.70
4.70
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes.
Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification
testing based on the conditions outlined in IPC Standard 7351 (IPC–7351).
¹ Height of these chips may create problems in wave soldering.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013
8
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Soldering Process
KEMET’s families of surface mount capacitors are compatible
Profile Feature
SnPb Assembly Pb-Free Assembly
with wave (single or dual), convection, IR, or vapor phase reflow
techniques. Preheating of these components is recommended
to avoid extreme thermal stress. KEMET's recommended
profile conditions for convection and IR reflow reflect the profile
conditions of the IPC/J–STD–020D standard for moisture
sensitivity testing. The devices can safely withstand a maximum
of three reflow passes at these conditions.
Preheat/Soak
Temperature Minimum (TSmin
)
100°C
150°C
150°C
200°C
Temperature Maximum (TSmax
)
Time (ts) from Tsmin to Tsmax
Ramp-up Rate (TL to TP)
)
60 – 120 seconds
3°C/seconds maximum
183°C
60 – 120 seconds
3°C/seconds maximum
217°C
Liquidous Temperature (TL)
Time Above Liquidous (tL)
60 – 150 seconds
60 – 150 seconds
220°C*
235°C**
250°C*
260°C**
Peak Temperature (TP)
Please note that although the X/7343–43 case size can withstand
wave soldering, the tall profile (4.3 mm maximum) dictates care in
wave process development.
Time within 5°C of Maximum
Peak Temperature (tP)
20 seconds maximum
6°C/seconds maximum
6 minutes maximum
30 seconds maximum
6°C/seconds maximum
8 minutes maximum
Ramp-down Rate (TP to TL)
Time 25°C to Peak
Temperature
Hand soldering should be performed with care due to the difficulty
in process control. If performed, care should be taken to avoid
contact of the soldering iron to the molded case. The iron should
be used to heat the solder pad, applying solder between the pad
and the termination, until reflow occurs. Once reflow occurs, the
iron should be removed immediately. “Wiping” the edges of a chip
and heating the top surface is not recommended.
Note: All temperatures refer to the center of the package, measured on the
package body surface that is facing up during assembly reflow.
*Case Size D, E, P, Y, and X
**Case Size A, B, C, H, I, K, M, R, S, T, U, V, W, and Z
TP
tP
Maximum Ramp Up Rate = 3ºC/seconds
Maximum Ramp Down Rate = 6ºC/seconds
TL
tL
During typical reflow operations, a slight darkening of the gold-
colored epoxy may be observed. This slight darkening is normal
and not harmful to the product. Marking permanency is not
affected by this change.
T
smax
T
smin
tS
25
25ºC to Peak
Time
Construction
Polymer /Ta2O5/Ta
Silver Adhesive
Silver Paint
Washer
Leadframe
Leadframe
(-Cathode)
(+Anode)
Carbon
Tantalum Wire
Weld
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013
9
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Capacitor Marking
(KO)
KEMET
Multi -
Anode
Polymer
Polarity
Indicator (+)
KM
Picofarad Code
KEMET ID
158
3 K
230
Rated
Voltage
Date
Code*
* 230 = 30th week of 2012
Date Code *
1st digit = Last number of Year
9 = 2009
0 = 2010
1 =2011
2 = 2012
3 = 2013
4 =2014
2nd and 3rd digit = Week of the Year
01 = 1st week of the Year to
52 = 52nd week of the Year
Storage
All KO-CAP series are shipped in moisture barrier bags with a desiccant and moisture indicator card. These series are classified
as MSL3 (Moisture Sensitivity Level 3). Product contained within the moisture barrier bags should be stored in normal working
environments with temperatures not to exceed 40°C and humidity not in excess of 60% RH.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013 10
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Tape & Reel Packaging Information
KEMET’s molded tantalum and aluminum chip capacitor families are packaged in 8 and 12 mm plastic tape on 7" and 13" reels in
accordance with EIA Standard 481–1: Embossed Carrier Taping of Surface Mount Components for Automatic Handling. This packaging
system is compatible with all tape-fed automatic pick-and-place systems.
8 mm (0.315")
or
12 mm (0.472")
180 mm (7.0")
Top Tape Thickness
or
0.10 mm (0.004")
330 mm (13.0")
Maximum Thickness
Table 3 – Packaging Quantity
Tape Width
Case Code
7" Reel*
13" Reel*
(mm)
KEMET
EIA
I
S
T
M
U
L
W
Z
V
A
B
C
D
Y
3216-10
3216-12
3528-12
3528-15
6032-15
6032-19
7343-15
7343-17
7343-20
3216-18
3528-21
6032-28
7343-31
7343-40
7343-43
7360-38
7360-20
8
8
8
8
12
12
12
12
12
8
3,000
2,500
2,500
2,000
1,000
1,000
1,000
1,000
1,000
2,000
2,000
500
12,000
10,000
10,000
8,000
5,000
5,000
3,000
3,000
3,000
9,000
8,000
3,000
2,500
2,000
2,000
2,000
2,500
8
12
12
12
12
12
12
500
500
500
500
X
E/T428P
H
1,000
* No C-Spec required for 7" reel packaging. C-7280 required for 13" reel packaging.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013 11
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
T
T
P2
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
2
E
1
Po
ØDo
Ao
F
Ko
W
E
2
B
1
Bo
S
1
P
1
T
1
Embossment
For cavity size,
see Note 1 Table 4
Center Lines of Cavity
ØD
1
Cover Tape
is for tape feeder reference only,
including draft concentric about B
B
1
o
.
User Direction of Unreeling
Table 4 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
D1 Minimum
Note 1
1.0
R Reference S1 Minimum
Tape Size
8 mm
D0
E1
P0
P2
T Maximum T1 Maximum
Note 2
Note 3
25.0
(0.984)
(0.039)
1.5 +0.10/-0.0
(0.059 +0.004/-0.0)
1.75 ±0.10
4.0 ±0.10
2.0 ±0.05
0.600
(0.024)
0.600
(0.024)
0.100
(0.004)
12 mm
16 mm
(0.069 ±0.004) (0.157 ±0.004) (0.079 ±0.002)
1.5
(0.059)
30
(1.181)
Variable Dimensions — Millimeters (Inches)
B1 Maximum
Note 4
4.35
(0.171)
8.2
(0.323)
12.1
(0.476)
Tape Size
8 mm
Pitch
E2 Minimum
F
P1
T2 Maximum W Maximum
A0,B0 & K0
6.25
(0.246)
10.25
(0.404)
14.25
3.5 ±0.05
4.0 ±0.10
2.5
(0.098)
4.6
8.3
(0.327)
12.3
Single (4 mm)
(0.138 ±0.002) (0.157 ±0.004)
5.5 ±0.05 8.0 ±0.10
(0.217 ±0.002) (0.315 ±0.004)
5.5 ±0.05 8.0 ±0.10
(0.217 ±0.002) (0.315 ±0.004)
Single (4 mm) &
Double (8 mm)
12 mm
16 mm
Note 5
(0.181)
4.6
(0.484)
16.3
Triple (12 mm)
(0.561)
(0.181)
(0.642)
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
2. The tape, with or without components, shall pass around R without damage (see Figure 5).
3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481–D, paragraph 4.3, section b).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 2).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 mm and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 3).
(e) see Addendum in EIA Standard 481–D for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013 12
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Packaging Information Performance Notes
1. Cover Tape Break Force: 1.0 Kg minimum.
2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width
8 mm
Peel Strength
0.1 to 1.0 Newton (10 to 100 gf)
0.1 to 1.3 Newton (10 to 130 gf)
12 and 16 mm
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180°
from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute.
3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA
Standards 556 and 624.
Figure 2 – Maximum Component Rotation
°
T
Maximum Component Rotation
Top View
Maximum Component Rotation
Side View
Typical Pocket Centerline
Tape
Maximum
°
°
T
s
Width (mm) Rotation (
)
8,12
16 – 200
20
10
Bo
Tape
Maximum
°
S
Width (mm) Rotation (
)
8,12
16 – 56
72 – 200
20
10
5
Typical Component Centerline
Ao
Figure 4 – Bending Radius
Figure 3 – Maximum Lateral Movement
Embossed
Carrier
Punched
Carrier
8 mm & 12 mm Tape
16 mm Tape
0.5 mm maximum
0.5 mm maximum
1.0 mm maximum
1.0 mm maximum
R
Bending
Radius
R
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013 13
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Figure 5 – Reel Dimensions
Full Radius,
W3 (Includes
flange distortion
at outer edge)
Access Hole at
Slot Location
(Ø 40 mm minimum)
See Note
W
2 (Measured at hub)
D
(See Note)
A
N
C
(Arbor hole
W
1 (Measured at hub)
diameter)
If present,
tape slot in core
for tape start:
2.5 mm minimum width x
10.0 mm minimum depth
B
(see Note)
Note: Drive spokes optional; if used, dimensions B and D shall apply.
Table 5 – Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size
8 mm
A
B Minimum
C
D Minimum
178 ±0.20
(7.008 ±0.008)
or
330 ±0.20
(13.000 ±0.008)
1.5
(0.059)
13.0 +0.5/-0.2
(0.521 +0.02/-0.008)
20.2
(0.795)
12 mm
16 mm
Variable Dimensions — Millimeters (Inches)
Tape Size
8 mm
N Minimum
W1
W2 Maximum
W3
8.4 +1.5/-0.0
(0.331 +0.059/-0.0)
12.4 +2.0/-0.0
(0.488 +0.078/-0.0)
16.4 +2.0/-0.0
14.4
(0.567)
18.4
(0.724)
22.4
50
(1.969)
Shall accommodate tape width
without interference
12 mm
16 mm
(0.646 +0.078/-0.0)
(0.882)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013 14
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Figure 6 – Tape Leader & Trailer Dimensions
Embossed Carrier
Carrier Tape
Round Sprocket Holes
Punched Carrier
8 mm & 12 mm only
START
END
Top Cover Tape
Elongated Sprocket Holes
(32 mm tape and wider)
100 mm
Minimum Leader
400 mm Minimum
Trailer
160 mm Minimum
Components
Top Cover Tape
Figure 7 – Maximum Camber
Elongated sprocket holes
(32 mm & wider tapes)
Carrier Tape
Round Sprocket Holes
1 mm Maximum, either direction
Straight Edge
250 mm
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013 15
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Paris, France
Tel: 33-1-4646-1006
Northeast Asia
Hong Kong
Tel: 852-2305-1168
2835 KEMET Way
Simpsonville, SC 29681
Sasso Marconi, Italy
Tel: 39-051-939111
Shenzhen, China
Tel: 86-755-2518-1306
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
Beijing, China
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Tel: 86-10-5829-1711
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Shanghai, China
Tel: 86-21-6447-0707
Kamen, Germany
Tel: 49-2307-438110
Corporate Offices
Fort Lauderdale, FL
Tel: 954-766-2800
Taipei, Taiwan
Tel: 886-2-27528585
Northern Europe
Bishop’s Stortford, United Kingdom
Tel: 44-1279-460122
North America
Southeast Asia
Singapore
Southeast
Tel: 65-6586-1900
Lake Mary, FL
Tel: 407-855-8886
Espoo, Finland
Tel: 358-9-5406-5000
Penang, Malaysia
Tel: 60-4-6430200
Northeast
Wilmington, MA
Tel: 978-658-1663
Bangalore, India
Tel: 91-806-53-76817
Central
Novi, MI
Tel: 248-994-1030
West
Milpitas, CA
Tel: 408-433-9950
Mexico
Guadalajara, Jalisco
Tel: 52-33-3123-2141
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013 16
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Other KEMET Resources
Tools
Resource
Location
Configure A Part: CapEdge
SPICE & FIT Software
http://capacitoredge.kemet.com
http://www.kemet.com/spice
http://www.kemet.com/keask
http://www.kemet.com:8080/elc
Search Our FAQs: KnowledgeEdge
Electrolytic LifeCalculator
Product Information
Resource
Location
Products
Technical Resources (Including Soldering Techniques)
RoHS Statement
http://www.kemet.com/products
http://www.kemet.com/technicalpapers
http://www.kemet.com/rohs
Quality Documents
http://www.kemet.com/qualitydocuments
Product Request
Resource
Location
http://www.kemet.com/sample
http://www.kemet.com/kits
Sample Request
Engineering Kit Request
Contact
Resource
Location
Website
Contact Us
Investor Relations
Call Us
www.kemet.com
http://www.kemet.com/contact
http://www.kemet.com/ir
1-877-MyKEMET
Twitter
http://twitter.com/kemetcapacitors
Disclaimer
All product specifications, statements, information and data (collectively, the “Information”) are subject to change without notice.
All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute – and we
specifically disclaim – any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite
experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the
use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained.
Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur.
Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or
redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013 17
KEMET Organic Capacitor (KO-CAP) – T530 High Capacitance/125°C Rated Polymer Tantalum
Digitally signed by Jeannette Calvo
DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corp., ou=Marketing Communications,
cn=Jeannette Calvo, email=jeannettecalvo@kemet.com
Date: 2013.02.27 16:28:26 -05'00'
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
T2019_T530 • 1/30/2013 18
相关型号:
T530X108K003AGE010
Tantalum Capacitor, Polarized, Tantalum (solid Polymer), 3V, 10% +Tol, 10% -Tol, 1000uF, Surface Mount, 2917, CHIP, LEAD FREE
KEMET
T530X108M003A
KEMET Organic Capacitor (KO-CAP) T530 High Capacitance/125°C Rated Polymer Tantalum
KEMET
T530X108M003AGE010
Tantalum Capacitor, Polarized, Tantalum (solid Polymer), 3V, 20% +Tol, 20% -Tol, 1000uF, Surface Mount, 2917, CHIP
KEMET
T530X108M003AHE010
Tantalum Capacitor, Polarized, Tantalum (solid Polymer), 3V, 20% +Tol, 20% -Tol, 1000uF, Surface Mount, 2917, CHIP
KEMET
T530X108M003ASE010
Tantalum Capacitor, Polarized, Tantalum (solid Polymer), 3V, 20% +Tol, 20% -Tol, 1000uF, Surface Mount, 2917, CHIP
KEMET
T530X108M004A
KEMET Organic Capacitor (KO-CAP) T530 High Capacitance/125°C Rated Polymer Tantalum
KEMET
T530X108M2R5A
KEMET Organic Capacitor (KO-CAP) T530 High Capacitance/125°C Rated Polymer Tantalum
KEMET
©2020 ICPDF网 联系我们和版权申明