KA-3529ASEL2Z4S [KINGBRIGHT]
Single Color LED,;型号: | KA-3529ASEL2Z4S |
厂家: | KINGBRIGHT CORPORATION |
描述: | Single Color LED, 光电 |
文件: | 总6页 (文件大小:545K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
3.5x2.8mm SMD CHIP LED LAMP
Part Number: KA-3529ASEL2Z4S
Hyper Red
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
zSingle color.
zThe Hyper Red device is based on light emitting diode
chip made from AlGaInP.
zSuitable for all SMD assembly and solder process.
zAvailable on tape and reel.
zElectrostatic discharge and power surge could damage
the LEDs.
zWhite SMD package, silicone resin.
zLow thermal resistance.
zIt is recommended to use a wrist band or anti-
electrostatic glove when handling the LEDs.
zAll devices, equipments and machineries must be
electrically grounded.
zPackage: 2000pcs / reel.
zMoisture sensitivity level : level 2a.
zRoHS compliant.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAN3501
APPROVED: Wynec
REV NO: V.3B
DATE: MAY/17/2016
DRAWN: L.T.Zhang
PAGE: 1 OF 6
CHECKED: Allen Liu
ERP: 1201008734
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exosEDsImpact may scratch the silicone lens or
damage the internal circuitry.
4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks.
4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup
and avoid damage during production.
5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
SPEC NO: DSAN3501
APPROVED: Wynec
REV NO: V.3B
DATE: MAY/17/2016
DRAWN: L.T.Zhang
PAGE: 2 OF 6
CHECKED: Allen Liu
ERP: 1201008734
Selection Guide
Iv (cd) [2]
@ 150mA
Φv (lm) [2]
@ 150mA
Viewing
Angle [1]
Emitting Color
(Material)
Lens Type
Part No.
2θ1/2
120°
Min.
3.1
Typ.
Min.
Typ.
12
KA-3529ASEL2Z4S
Notes:
Hyper Red(AlGaInP)
Water Clear
4.2
8.6
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous flux: +/-15%.
3. LEDs are binned according to their luminous flux.
4. Luminous intensity/ luminous Flux value is traceable to CIE127-2007 standards.
Absolute Maximum Ratings at TA=25°C
Parameter
Power Dissipation
Symbol
Value
Unit
PD
450
mW
Junction Temperature [1]
Operating Temperature
Storage Temperature
TJ
110
°C
°C
°C
Top
Tstg
-40 To +85
-4To +85
DC Forward Current [1]
Peak Forward Current [2]
IF
10
350
mA
mA
IFM
Thermal Resistance [1]
(Junction/ambient)
Rj-a
h j-
155
60
°C/W
°C/W
Thermal Resistance [1]
(Junction/solder point)
Notes:
1.Results from mounting on PC bard FR4(psize70mm2), ounted on pc board-metal core PCB is recommend
for lowest thermal Resistance.
2.1/10 Duty Cycle, 0.1ms Pse idth.
3. Relative humidity levels maietween 40% and 60% in production area are recommended to avoid the build-up of static
electricity – Ref JEDEC/JESD5-A and JEDEC/J-STD-033.
Electrical / Optical Characteristics at TA=25°C
Symbol
λpeak
λD [1]
Δλ1/2
C
Parameter
Peak Wavelength
Dominant Wavelength
Spectral Line Half-width
Capacitance
Emitting Color
Hyper Red
Hyper Red
Hyper Red
Hyper Red
Hyper Red
Hyper Red
Typ.
631
623
20
Max.
Units
nm
nm
nm
pF
Test Conditions
IF=150mA
IF=150mA
IF=150mA
27
VF=0V;f=1MHz
IF=150mA
VF [2]
IR
Forward Voltage
2.5
3.0
10
V
Reverse Current
uA
VR = 5V
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to CIE127-2007 standards.
4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
SPEC NO: DSAN3501
APPROVED: Wynec
REV NO: V.3B
DATE: MAY/17/2016
DRAWN: L.T.Zhang
PAGE: 3 OF 6
CHECKED: Allen Liu
ERP: 1201008734
Hyper Red
KA-3529ASEL2Z4S
SPEC NO: DSAN3501
APPROVED: Wynec
REV NO: V.3B
DATE: MAY/17/2016
DRAWN: L.T.Zhang
PAGE: 4 OF 6
CHECKED: Allen Liu
ERP: 1201008734
KA-3529ASEL2Z4S
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Reel Dimension
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Tape Specifications
(Units : mm)
SPEC NO: DSAN3501
APPROVED: Wynec
REV NO: V.3B
DATE: MAY/17/2016
DRAWN: L.T.Zhang
PAGE: 5 OF 6
CHECKED: Allen Liu
ERP: 1201008734
PACKING & LABEL SPECIFICATIONS
KA-3529ASEL2Z4S
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsi-
ble for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.kingbright.com/application_notes
SPEC NO: DSAN3501
APPROVED: Wynec
REV NO: V.3B
DATE: MAY/17/2016
DRAWN: L.T.Zhang
PAGE: 6 OF 6
CHECKED: Allen Liu
ERP: 1201008734
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 202
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 202
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 202
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 202
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 202
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 202
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 202
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 202
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 202
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 202
-
VISHAY
©2020 ICPDF网 联系我们和版权申明