KA-8070QB10Z1S [KINGBRIGHT]
SINGLE COLOR LED, BLUE, 6.2mm, ROHS COMPLIANT PACKAGE-2;型号: | KA-8070QB10Z1S |
厂家: | KINGBRIGHT CORPORATION |
描述: | SINGLE COLOR LED, BLUE, 6.2mm, ROHS COMPLIANT PACKAGE-2 光电 |
文件: | 总9页 (文件大小:288K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
KA-8070 SERIES
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
●High efficient lightsource.
●Designed for high current operation.
●Low thermal resistance.
●Encapsulation : Silicone resin.
●Compatible with IR-reflow processes.
●ESD protection .
Applications
z Substitution of micro incandescent lamps.
z Portable light source.
z Signal and symbol luminaire for orientation.
z Marker lights (e.g. steps, exit ways, etc).
z Decorative and entertainment lighting.
z Commercial and residential lighting.
z Emergency-vehicle lighting.
●Package : 500pcs / reel.
●RoHS compliant.
Application Note
Static electricity and surge damage the LEDS.
It is recommended to use a wrist band or anti-electrostatic
glove when handling the LEDs.
All devices, equipment and machinery must be electrically
grounded.
Package Dimensions
CHIP
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAJ6326
APPROVED: WYNEC
REV NO: V.4
DATE: JAN/22/2011
DRAWN: C.H.HAN
PAGE: 1 OF 9
CHECKED: Allen Liu
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4.1. The outer diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks. The inner
diameter of the nozzle should be as large as possible.
4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup
and avoid damage during production.
5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
SPEC NO: DSAJ6326
APPROVED: WYNEC
REV NO: V.4
DATE: JAN/22/2011
DRAWN: C.H.HAN
PAGE: 2 OF 9
CHECKED: Allen Liu
Flux Characteristics at 350mA Ambient Temperature, Ta = 25°C
Typical Luminous Flux
(lm) [1]
Luminous Flux (lm) @ 350mA [1]
Color
Part No.
Code.
B5
Min.
20
24
29
20
24
29
42
50
60
12
14
17
8.6
10
12
12
14
17
Max.
24
29
35
24
29
35
50
60
70
14
17
20
10
12
14
14
17
20
Typ.
Reddish-Orange(AlGaInP)
KA-8070SE28Z1S
B6
27
B7
B5
Super Bright Yellow (AlGaInP) KA-8070SY28Z1S
B6
29
55
15
11
16
B7
B9
Green(AlGaInN)
Blue(InGaN)
KA-8070ZG10Z1S
KA-8070QB12Z1S
KA-8070QB38Z1S
KA-8070QB10Z1S
B10
B11
B2
B3
B4
A17
B1
Blue(InGaN)
B2
B2
Blue(AlGaInN)
B3
B4
Note:
1.Minimum luminous flux performance guaranteed within published operating conditions.Kingbright maintains tolerance of +/-15% on flux.
Optical Characteristics at 350mA Ambient Temperature, Ta = 25°C
Typical
Temperature
Coefficient of
Dominant
Wavelength
(nm/°C)
Typical
Viewing
Angle [3]
(degrees)
2θ1/2
Typical
Spectral
Halfwidth [2]
(nm)
Dominant Wavelength [1] λD
Part No.
Δλ1/2
ΔλD /ΔT
Min.
Typ.
Max.
KA-8070SE28Z1S
619nm
625nm
629nm
30
0.05
120°
KA-8070SY28Z1S
KA-8070ZG10Z1S
KA-8070QB12Z1S
586nm
520nm
450nm
588nm
530nm
594nm
535nm
20
35
25
0.06
0.14
0.04
120°
120°
454nm 457.5nm
120°
KA-8070QB38Z1S
KA-8070QB10Z1S
445nm
-
450nm
452nm
455nm
458nm
24
20
0.03
0.1
120°
120°
Notes:
1.Dominant wavelength is derived from the CIE 1931 Chromaticity diagram and represents the perceived color.
2.Spectral width at 1/2 of the peak intensity.
3.Viewing angle is the off axis angle from lamp centerline where the luminous intensity is 1/2 of the peak value.
SPEC NO: DSAJ6326
APPROVED: WYNEC
REV NO: V.4
DATE: JAN/22/2011
DRAWN: C.H.HAN
PAGE: 3 OF 9
CHECKED: Allen Liu
Electrical Characteristics at 350mA Ambient Temperature, Ta = 25°C
Typical Temperature
Typical
Thermal
Resistance
(°C/W)
Coefficient of
Forward
Voltage [2]
(mV/°C)
Forward Voltage Vf [1]
(V)
Part No.
Rth j-slug
ΔVf /ΔT
Min.
Typ.
2.5
2.5
3.3
3.5
3.5
3.2
Max.
KA-8070SE28Z1S
KA-8070SY28Z1S
KA-8070ZG10Z1S
KA-8070QB12Z1S
KA-8070QB38Z1S
KA-8070QB10Z1S
2.0
2.0
2.8
-
3.0
3.0
3.8
4.1
4.1
3.6
-3.2
-3.2
-2.3
-2.2
-2.2
-3.2
16
9
12
11
11
9
-
2.7
Notes:
1.Kingbright maintains a tolerance of +/- 0.1V on forward voltage measurements.
2.Measured between 25 °C < TJ < 110 °C at IF = 350 mA.
Absolute Maximum Ratings
Parameter
Reddish-Orange /Super Bright Yellow/Green/Blue
DC Forward Current (mA) [1]
Peak Pusled Forward Current (mA)
Average Forward Current (mA)
Reverse Voltage (V)
350
500
350
5
ESD Sensitivity
8000V HBM
110
LED Junction Temperature (°C)
Operation Temperature (°C)
Storage Temperature (°C)
Soldering Temperature (°C)
Note:
-40 to+ 100
-40 to+ 110
260 For 5 Seconds
1. Proper current derating must be observed to maintain junction temperature below the maximum.
Moisture Sensitivity
KA-8070 LEDs are packaged in airtight and moisture-resistant bags to prevent moisture absorption which may lead to
catastrophic failure in reflow soldering process. Kingbright recommends that the devices must be baked before soldering if
they are removed from the original package, and are exposed to environmental conditions for longer than the durations
(unit: days) defined in the table below. Recommended baking conditions are 24 hours at 80ºC.
Maximum Percent Relative Humidity
Temperature
30%
40%
50%
60%
70%
80%
1
90%
1
30°C
25°C
20°C
9
5
4
3
1
12
17
7
9
5
7
4
6
2
2
1
2
1
1
Storage Conditions
After being removed from the original sealed package, KA-8070 LEDs should be stored at a temperature of 25 ºC with a
relative humidity lower than 10%. Under such conditions, storage duration is excluded from the exposure duration as defined
in the Moisture Sensitivity section.
SPEC NO: DSAJ6326
APPROVED: WYNEC
REV NO: V.4
DATE: JAN/22/2011
DRAWN: C.H.HAN
PAGE: 4 OF 9
CHECKED: Allen Liu
Wavelength Characteristics Ta = 25°C
Light Output Characteristics
SPEC NO: DSAJ6326
APPROVED: WYNEC
REV NO: V.4
CHECKED: Allen Liu
DATE: JAN/22/2011
DRAWN: C.H.HAN
PAGE: 5 OF 9
Forward Current Characteristics, Ta = 25°C
SPEC NO: DSAJ6326
APPROVED: WYNEC
REV NO: V.4
DATE: JAN/22/2011
DRAWN: C.H.HAN
PAGE: 6 OF 9
CHECKED: Allen Liu
Current Derating Curves
Representative Typical Spatial Radiation Pattern
SPEC NO: DSAJ6326
APPROVED: WYNEC
REV NO: V.4
DATE: JAN/22/2011
DRAWN: C.H.HAN
PAGE: 7 OF 9
CHECKED: Allen Liu
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Reel Dimension
Recommended Soldering Pattern
(Units : mm ; Tolerance: ± 0.1)
Tape Dimensions
(Units : mm)
SPEC NO: DSAJ6326
APPROVED: WYNEC
REV NO: V.4
DATE: JAN/22/2011
DRAWN: C.H.HAN
PAGE: 8 OF 9
CHECKED: Allen Liu
PACKING & LABEL SPECIFICATIONS
KA-8070 SERIES
數位簽署者:yalin
DN:cn=yalin,o,
ya
ou=SPE
C 專用,
email=yalin@ yalin.
com,c=<無>
日期 2011.01.22
16:48:05+08'00'
lin
SPEC NO: DSAJ6326
APPROVED: WYNEC
REV NO: V.4
DATE: JAN/22/2011
DRAWN: C.H.HAN
PAGE: 9 OF 9
CHECKED: Allen Liu
相关型号:
©2020 ICPDF网 联系我们和版权申明