KPC-1608SYCK [KINGBRIGHT]
1.6*0.8*1.06mm kingbright SMD;
| 型号： | KPC-1608SYCK |
| 厂家： | 
KINGBRIGHT CORPORATION |
| 描述： | 1.6*0.8*1.06mm kingbright SMD |
| 文件： | 总5页 (文件大小：689K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
1.6X0.8mm SMD CHIP LED LAMP
Part Number: KPC-1608SYCK
Super Bright Yellow
Features
Description
z 1.6mmX0.8mm SMD LED, 1.06mm thickness.
z Low power consumption.
The Super Bright Yellow device is made with AlGaInP (on
GaAs substrate) light emitting diode chip.
z Wide viewing angle.
z Ideal for backlight and indicator.
z Package: 3000pcs / reel.
z Moisture sensitivity level : level 3.
z RoHS compliant.
Package Dimensions
Notes:
唐希：13760227272
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4.The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAN4360
APPROVED: Wynec
REV NO: V.2B
DATE: MAY/30/2016
DRAWN: W.Q.Zhong
PAGE: 1 OF 5
CHECKED: Allen Liu
ERP: 1203014137
Selection Guide
Iv (mcd) [2]
@ 20mA
Viewing
Angle [1]
Part No.
Emitting Color (Material)
Lens Type
Min.
Typ.
2θ1/2
KPC-1608SYCK
Super Bright Yellow (AlGaInP)
Water Clear
80
150
150°
QQ：2160785368
唐希：13760227272
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous Flux: +/-15%.
3. Luminous intensity value is traceable to CIE127-2007 standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
λpeak
λD [1]
Δλ1/2
C
Parameter
Peak Wavelength
Dominant Wavelength
Spectral Line Half-width
Capacitance
Emitting Color
Typ.
590
590
20
Max.
Units
Test Conditions
IF=20mA
Super Bright Yellow
Super Bright Yellow
Super Bright Yellow
Super Brht w
Super ight
Sut Yellow
m
nm
nm
pF
V
IF=20mA
IF=20mA
20
VF=0V;f=1MHz
IF=20mA
VF [2]
IR
Forward Voltage
2
2.5
10
Reverse Current
uA
VR=5V
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceablCIE17-2007 standards.
4. Excess driving current and / or erating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Values
75
Units
mW
mA
mA
V
Power dissipation
DC Forward Current
Peak Forward Current [1]
Reverse Voltage
30
175
5
Operating Temperature
Storage Temperature
-40°C To +85°C
-40°C To +85°C
QQ：2160785368
Notes: 唐希：13760227272
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static
electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.
SPEC NO: DSAN4360
APPROVED: Wynec
REV NO: V.2B
DATE: MAY/30/2016
DRAWN: W.Q.Zhong
PAGE: 2 OF 5
CHECKED: Allen Liu
ERP: 1203014137
Super Bright Yellow
KPC-1608SYCK
SPEC NO: DSAN4360
APPROVED: Wynec
REV NO: V.2B
DATE: MAY/30/2016
DRAWN: W.Q.Zhong
PAGE: 3 OF 5
CHECKED: Allen Liu
ERP: 1203014137
KPC-1608SYCK
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reeenion
Tape Dimensions
(Units : mm)
唐希：13760227272
SPEC NO: DSAN4360
APPROVED: Wynec
REV NO: V.2B
CHECKED: Allen Liu
DATE: MAY/30/2016
DRAWN: W.Q.Zhong
PAGE: 4 OF 5
ERP: 1203014137
PACKING & LABEL SPECIFICATIONS
KPC-1608SYCK
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.kingbright.com/application_notes
SPEC NO: DSAN4360
APPROVED: Wynec
REV NO: V.2B
DATE: MAY/30/2016
DRAWN: W.Q.Zhong
PAGE: 5 OF 5
CHECKED: Allen Liu
ERP: 1203014137
相关型号：
KPC-3216
The High Effciency Red sourse color devices are made with Galium Arsenide Phosphide Orange Light Emitting Diode
KINGBRIGHT
KPC-3216CGCK
SINGLE COLOR LED, GREEN, 2mm, 3.20 X 1.60 MM, 1.10 MM HEIGHT, ROHS COMPLIANT, SMD, 2 PIN
KINGBRIGHT
KPC-3216EC
The High Effciency Red sourse color devices are made with Galium Arsenide Phosphide Orange Light Emitting Diode
KINGBRIGHT
KPC-3216MBC
Single Color LED, Blue, Water Clear, 2mm, 3.20 X 1.60 MM, 1.10 MM HEIGHT, SMD, 2 PIN
KINGBRIGHT
KPC-3216MGC
Single Color LED, Mega Green, Water Clear, 2mm, 3.20 X 1.60 MM, 1.10 MM HEIGHT, ROHS COMPLIANT, SMD, 2 PIN
KINGBRIGHT
KPC-3216PBC-A
SINGLE COLOR LED, BLUE, 2mm, 3.20 X 1.60 MM, 1.10 MM HEIGHT, ROHS COMPLIANT, SMD, 2 PIN
KINGBRIGHT
KPC-3216SGC
The High Effciency Red sourse color devices are made with Galium Arsenide Phosphide Orange Light Emitting Diode
KINGBRIGHT
©2020 ICPDF网 联系我们和版权申明