MAX34334CSE 第1页-第5页 PDF中文翻译页面详情预览
1.6×0.8mm的SMD贴片LED LAMP
Part Number: KPT-1608SECK
超级明亮的橙色
特点
1.6mmX0.8mm SMT LED , 0.75毫米厚度。
低功耗。
广视角。
理想背光和指示。
包装: 2000个/卷。
湿度敏感度等级: 3级。
符合RoHS 。
描述
超级明亮的橙色装置是用的AlGaInP (上
GaAs基板)发光二极管芯片。
包装尺寸
K
g
in
ig
r
b
t
h
注意事项:
1.所有尺寸为毫米(英寸) 。
2.公差为± 0.1( 0.004" ),除非另有说明。
3,规格,特性和在数据表中所描述的技术参数如有更改,恕不另行通知。
4.该设备具有一个单个的安装表面。设备必须按照规范进行安装。
SPEC NO: DSAB1874
批准: WYNEC
REV NO: V.21A
检查:艾伦刘
DATE: JUN/26/2015
DRAWN: M.Liu
页次: 1/5
ERP: 1203001727
选购指南
产品型号
Emitting Color (Material)
镜头类型
IV( MCD ) [ 2 ]
@ 20毫安
分钟。
KPT-1608SECK
超级明亮的橙色(铝镓铟磷)
无色透明
120
*80
注意事项:
1.
θ1
/ 2 is the angle from optical centerline where the luminous intensity is 1 / 2 of the optical peak value.
2. Luminous intensity / luminous Flux: + / -15%.
*发光强度值可溯源到CIE127-2007符合国家标准。
VIEWING
角[1]
2θ1/2
120
°
典型值。
250
*180
在TA电气/光学特性= 25°C
符号
λpeak
λD
[1]
Δλ1/2
C
V
F
[2]
I
R
参数
峰值波长
主波长
谱线半宽
电容
正向电压
反向电流
发光颜色
超级明亮的橙色
超级明亮的橙色
超级明亮的橙色
超级明亮的橙色
典型值。
610
马克斯。
超级明亮的橙色
超级明亮的橙色
注意事项:
1. Wavelength: + / -1nm.
2. Forward Voltage: + / -0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
in
K
b
g
ig
r
601
29
15
2.1
t
h
2.5
10
V
单位
nm
测试条件
I
F
=20mA
I
F
=20mA
I
F
=20mA
V
F
=0V;f=1MHz
I
F
=20mA
V
R
=5V
nm
nm
pF
uA
在Ta绝对最大额定值= 25°C
参数
功耗
直流正向电流
峰值正向电流[ 1 ]
反向电压
工作温度
储存温度
注意:
1. 1 / 10 Duty Cycle, 0.1ms Pulse Width.
75
30
195
5
-40 ° C至+ 85°C
-40 ° C至+ 85°C
单位
mW
mA
mA
V
SPEC NO: DSAB1874
批准: WYNEC
REV NO: V.21A
检查:艾伦刘
DATE: JUN/26/2015
DRAWN: M.Liu
页次: 2/5
ERP: 1203001727
超级明亮的橙色
t
h
ig
r
b
g
in
K
KPT-1608SECK
SPEC NO: DSAB1874
批准: WYNEC
REV NO: V.21A
检查:艾伦刘
DATE: JUN/26/2015
DRAWN: M.Liu
页次: 3/5
ERP: 1203001727
KPT-1608SECK
回流焊接,建议与焊接信息如下所示。
其他焊接方法不推荐,因为它们可能会导致产品损坏。
推荐焊接模式
(单位:mm ;公差: ± 0.1 )
带尺寸
(单位:毫米)
K
g
in
ig
r
b
REEL DIMENSION
t
h
SPEC NO: DSAB1874
批准: WYNEC
REV NO: V.21A
检查:艾伦刘
DATE: JUN/26/2015
DRAWN: M.Liu
第4页: 5
ERP: 1203001727
包装&标签规范
KPT-1608SECK
K
g
in
ig
r
b
t
h
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at
http://www.kingbright.com/application_notes
SPEC NO: DSAB1874
批准: WYNEC
REV NO: V.21A
检查:艾伦刘
DATE: JUN/26/2015
DRAWN: M.Liu
第5页: 5
ERP: 1203001727
相关元器件产品Datasheet PDF文档

KPT-1608SGC

1.6x0.8mm SUPER THIN SMD CHIP LED LAMPS
141 KINGBRIGHT

KPT-1608SGD

1.6x0.8mm SUPER THIN SMD CHIP LED LAMPS
暂无信息
23 KINGBRIGHT

KPT-1608SGT

1.6x0.8mm SUPER THIN SMD CHIP LED LAMPS
暂无信息
14 KINGBRIGHT

KPT-1608SRC

1.6x0.8mm SUPER THIN SMD CHIP LED LAMPS
暂无信息
26 KINGBRIGHT

KPT-1608SRC-PRV

暂无描述
暂无信息
0 KINGBRIGHT

KPT-1608SRD

1.6x0.8mm SUPER THIN SMD CHIP LED LAMPS
暂无信息
18 KINGBRIGHT