CR2A10YTE220/221J [KOA]
Capacitor/Resistor Chip Networks; 电容/电阻片上网络型号: | CR2A10YTE220/221J |
厂家: | KOA SPEER ELECTRONICS, INC. |
描述: | Capacitor/Resistor Chip Networks |
文件: | 总8页 (文件大小:90K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
KOA SPEER ELECTRONICS, INC.
SS-192 R4
AHA 12/19/03
CERTIFIED
Capacitor/Resistor Chip Networks
Type CR2A10Y
1. Scope
This specification shall be applied to CR chip networks CR2A10Y
produced by KOA Corporation.
2. Related Standard
JIS C 5102 (1994) Test method of fixed capacitors for use in electronic equipment.
JIS C 5202 (1994) Test method of fixed resistors for use in electronic equipment.
JIS C 6429 (1991) Fixed Multilayer Ceramic Chip capacitors for use in electronic equipment.
JIS C 0806 (1990) Packaging of electronic components on continuous tapes
(surface mounting devices).
3. Dimensions
C
C
3-1 Dimensions
W
D
D
411
B
D
P
A
L
T
A
D
unit: inches (mm)
L
W
C
D
T
A
B
P
.157 .008 .083 .008 .012 .008 .016 .006 .028 .004
.02
.006
.031
(4.0 0.2) (2.1 0.2) (0.3 0.2) (0.4 0.15) (0.7 0.1) (0.5 Ref.) (0.15 Ref.) (0.8 Ref.)
PAGE 1 OF 8
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-192 R4
3-2. Circuit Schematic
3-3. Structure
10
9
8
7
1
3
1 Alumina Ceramic
2 Passivation
3 Ni & Solder Plating
1
6
41
1
2
2
3
4
5
4. Type Designation
The type designation shall be the following form:
Y
TE
CR
xxxM/xxxJ
2A10
Style
Chip Size
Circuit
Packaging
Capacitance Tolerance/Resistance Tolerance
3 Digit Numbers +1 for
Resistance Tolerance for each
Ex: 270M/510J
CR Chip
Networks
.157" x .083"
4.0 x 2.1 mm
TE: Embossed Taping
No Designation: Bulk
5. Rating
Operating environment -25°C ~ +85°C
Capacitor Item
Capacitor Rating
1 KHz 10%
(1 Vrms 0.2V)
Resistor Item
Resistor Rating
Capacitance Measuring
Condition
Power Rating
0.063 W
Voltage Rating
25V (DC)
Maximum Working Voltage
Maximum Overload Voltage
7.9 V
Capacitance Tolerance
Temperature Coefficient
20%/ 30%
+20%/-55%
15.8 V
Temperature Coefficient
(-25°C ~ +85°C)
200 ppm/°C
Dissipation Factor
3% maximum
Resistor Tolerance
(at 1 KHz 1.0 Vrms)
5%
Insulation Resistance
1,000 MΩ minimum Rating Ambient Temperature
+ 70°C
Dielectric Withstanding Voltage
62.5V DC 5 sec. Operating Temperature Range
50 mA charge
-25°C to +85°C
Operating Temperature Range
Capacitance Range
-25°C to +85°C
Resistor Range
22pF, 47pF, 100pF
22Ω, 47Ω,100Ω,
220Ω, 470Ω, 1KΩ, 47KΩ
PAGE 2 OF 8
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-192 R4
5-2 Rated Voltage
The rated voltage is limited to the maximum
working voltage.
The maximum value DC voltage capable
of being applied continuously to a resistor
at the rated ambient temperature. Rated
voltage shall be calculated from the following
formula:
Power Derating Curve
120
100
80
60
40
20
0
Where:
E = Rated voltage (V)
E =
√
P x R P = Rated power (W)
R = Nominal resistance (Ω)
-30 -20 -10
0
10 20 30 40 50 60 70 80 90
Ambient Temperature (°C)
6. Marking
6-1 Apply a mark of 1st terminal for a position of 1st terminal.
6-2 Marking Code
Type
Capacitance (pF)
Resistance (Ω)
Marking Code
CR2A10YTE220/220J
CR2A10YTE220/470J
CR2A10YTE220/101J
CR2A10YTE220/221J
CR2A10YTE220/471J
CR2A10YTE220/102J
CR2A10YTE470/220J
CR2A10YTE470/470J
CR2A10YTE470/101J
CR2A10YTE470/221J
CR2A10YTE470/471J
CR2A10YTE470/102J
CR2A10YTE101/220J
CR2A10YTE101/470J
CR2A10YTE101/101J
CR2A10YTE101/221J
CR2A10YTE101/471J
CR2A10YTE101/102J
CR2A10YLTE101M/473J
22
22
22
47
120
140
111
121
141
112
220
240
211
221
241
212
420
440
411
421
441
412
443
22
100
220
470
1K
22
22
22
47
22
47
47
47
100
220
470
1K
47
47
47
100
100
100
100
100
100
100
22
47
100
220
470
1K
47K
PAGE 3 OF 8
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-192 R4
7. Test Condition
Unless otherwise specified, the test shall be
performed in accordance with JIS-C-5020
specifying at the temperature of 20 °C 15°C
and at the humidity of 65% 20%.
In case doubts arise about the test results,
the test shall be performed at the temperature
of 20°C 2°C and at the humidity of 65% 5%.
8. Reliability Test
8-1 Electrical Characteristics
No.
Item
Requirement
Test Methods
Insulation
Resistance
More than 104 MΩ
Within 2 minutes at DC 25V between terminal
and another
1
v
2
Dielectric
Withstanding
Voltage
No evidence of fuming
flaming or breakdown
2.5 times maximum rated voltage for 5 seconds
with 50 mA maximum charging current
v
PAGE 4 OF 8
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-192 R4
8-2 Mechanical Characteristics
Item
Requirement
Test Methods
No.
Resistance to
Soldering Heat
No evidence of damage
∆C within 20%
Immerse in the solder (H63A) of 260°C 5°C for
10 1 seconds. Measurement shall be done 24
hours at room condition after test.
1
4
∆R within
5%
D. F. within 5%
I. R. more than 100 MΩ
2
3
Solderability
Approximately 95% of the
terminal should be covered
with new solder
Immerse in the solder (H63A) of 235°C 5°C
for 3 0.5 seconds.
Terminal Strength
(Bend test)
No mechanical damage
Specimen shall be soldered on PCB and support
by applying strength so that the bending width
becomes 3mm.
4
5
Resistance to
Solvents
No mechanical damage
No evidence of damage
Immerse in the IPA of 20 ~ 25°C
for 60 10 seconds.
Vibration
2 hours in each direction of X,Y,Z on PCB at a
frequency range of 10-55-10Hz with 1.5mm amplitude.
Measurement shall be done 24 4 hours at room
condition after test.
8-3 Environmental Characteristics
Item
Requirement
Test Methods
No.
1
Temperature
cycling
100 cycles between -40°C/30 minutes and
+125°C/30 minutes. Measurement shall be
done 24 4 hours at room condition after test.
No evidence of damage
∆C within 20% ∆R within 5%
D.F. within 5% I.R. more than 100 MΩ
Humidity
(No Load)
MIL-STD-202F Method 106 10 cycles
Measurement shall be done 24 4 hours
at room condition after test.
2
3
No evidence of damage
∆C within 20% ∆R within 5%
D.F. within 5% I.R. more than 100 MΩ
Moisture
Resistance
Temperature 40°C 2°C Humidity 90% ~ 95%
1000 hours
DC 50V 1.5 hours ON 0.5 hours OFF
Measurement shall be done 24 4 hours
at room condition after test.
No evidence of damage
∆C within 20% ∆R within 5%
D.F. within 5% I.R. more than 100 MΩ
4
Load Life
No evidence of damage
∆C within 20% ∆R within 5%
D.F. within 5% I.R. more than 100 MΩ
Temperature 70°C 2°C 1000 hours
DC 50V 1.5 hours ON 0.5 hours OFF
Measurement shall be done 24 4 hours
at room condition after test.
PAGE 5 OF 8
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-192 R4
9. Packaging
9-1 Bulk Packaging
100 pieces chip are packed in a poly bag.
The package shall be marked:
(1) Type Designation (CR2A10Y)
(2) Nominal Capacitance/Nominal Resistance
(3 digit/3 digit)
(3) Quantity
(4) Production Lot. No.
(5) Manufacturer’s name
9-2 Taping
The taping shall be embossed carrier tapes
of 12 mm width and 4 mm pitches.
The standard quantity per reel shall be 4000 pieces.
(1) Carrier Tape
P0
P2
øD
E
F
W
B
2nd Terminal
T2
P1
A
Tape Running Direction
T1
(unit: mm)
Type
A
B
W
E
F
CR2A10Y
2.5 0.2
4.4 0.2
12.0 0.2
1.75 0.1
5.5 0.1
T1
T2
P0
P1
P2
øD
0.1
- 0
1.15 0.2
0.25 0.05
4.0 0.1
4.0 0.1
2.0 0.1
1.5
Top tape peeling strength: 10 ~ 55g
PAGE 6 OF 8
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-192 R4
(2) Reel
A
B
D
W
(unit: mm)
W
A
B
D
178 2.0
60 2.0
21 0.8
10 1.0
(3) Leader and End Tape
Leader tape
150 (+20)
End tape
300 (+20)
(4,000 pieces)
350 (+20)
Empty
Top tape
Empty
Tape Running Direction
(4) Contents on label
(1) Type Designation (CR2A10Y)
(2) Nominal Capacitance/Nominal Resistance (3 digit/3 digit)
(3) Quantity
(4) Customer’s code No.
(5) Production lot No. Manufacturer’s name
(6) Manufacturer’s name
PAGE 7 OF 8
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA SPEER ELECTRONICS, INC.
SS-192 R4
10. Land Pattern Design
F
G
D
B W A
C
E
L
(unit: mm)
L
W
A
B
C
D
E
F
G
4.0
2.1
1.7
3.1
0.4
0.4
0.8
5.1
3.5
11. Soldering
11-1 Reflow Soldering
Reflow soldering should be done at 240°C for less than 20 seconds.
Temperature (°C)
1. The melting time of soldering should
be as short as possible.
300
200 ~ 240°C
~ 4°C/sec
1
2. After the soldering, allow products
to cool naturally.
200
100
150°C
3. We do not recommend flow soldering
to CR Chip Networks, because of concern
that a solder bridge occurs due to narrow
0.8 mm pitch. We therefore recommend
reflow soldering.
cooling
naturally
60 ~ 120
sec
5 ~ 30 sec
30
~
60 sec
11-2 Cleaning
1. Residual flux after board washing may cause solder migration.
Carefully check the status of board washing.
2. Confirm they will not cause problems when they are not washed.
11-3 Others
1. This product has circuits on both sides. Do not use adhesives, because
of concern that characteristics will be impaired by adhesives.
2. Do not use the products in dewy atmosphere.
PAGE 8 OF 8
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
相关型号:
CR2AA1600J100S2
Fixed Resistor, Metal Glaze/thick Film, 0.2W, 160ohm, 5% +/-Tol, -100,100ppm/Cel, 0705,
VISHAY
CR2AA2201G100S2
Fixed Resistor, Metal Glaze/thick Film, 0.2W, 2200ohm, 2% +/-Tol, -100,100ppm/Cel, 0705,
VISHAY
CR2AA2263F100S2
Fixed Resistor, Metal Glaze/thick Film, 0.2W, 226000ohm, 1% +/-Tol, -100,100ppm/Cel, 0705,
VISHAY
©2020 ICPDF网 联系我们和版权申明