KL731ETE18NG [KOA]
General Purpose Inductor, 0.018uH, 2%, 1 Element, Alumina Ceramic-Core, SMD, 0402;
| 型号： | KL731ETE18NG |
| 厂家： | 
KOA SPEER ELECTRONICS, INC. |
| 描述： | General Purpose Inductor, 0.018uH, 2%, 1 Element, Alumina Ceramic-Core, SMD, 0402 |
| 文件： | 总12页 (文件大小：154K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TN-200
CERTIFIED
Thin Film Chip Inductors
Typ e KL7 3 S e rie s
1. Scope
This specification applies to Thin Film Chip Inductors (KL73) 1E, 1J, 2A and 2B sizes
produced by KOA Corporation.
2. Type Designation
The type designation shall be the following form:
1E
G
10N
KL73
TE
1J
2A
2B
Tolerance
Nominal
Inductance
Type
Packaging
Chip Size
.039 X .020 X .014"
C: ± 0.2nH
(≤ 4.7nH only)
G: ±2%
(1.0 X 0.5 X 0.35 mm)
Thin Film
Chip Inductors
TE: Embossed Taping
No Designation: Bulk
.063 X .031 X.020"
(1.6 X 0.8 X 0.5 mm)
J: ±5%
.079 X .049 X .020"
(2.0 X 1.25 X 0.5 mm)
.126 X .063 X .024"
(3.2 X 1.6 X 0.6 mm)
3. Rating
Ratings
0805
Item
0402
0603
1206
Nominal Inductance Range (nH)
Inductance Tolerance
1.0 ~ 27
1.0 ~ 82
1.0 ~ 82
2.2 ~ 100 (E-12 series)
± 2%, ± 5% (± 0.2nH: Under 4.7nH)
Quality Factor (typ.)
10 ~ 7
12 ~ 25
15 ~ 32
600 ~ 13,000
0.03 ~ 4.00
17 ~ 44
Self Resonant Frequency (typ.) (MHz) 12,000 ~ 1,500 600 ~ 13,000
470 ~ 9,000
0.07 ~ 1.90
250 ~ 1,000
DC Resistance (typ.) (Ω)
0.15 ~ 5.00
700 ~ 150
0.05 ~ 4.50
100 ~ 650
Allowable Current (max.) (mA)
Operating Temperature Range (°C)
Storage Temperature Range (°C)
150 ~ 900
-40°C ~ +85°C
-40°C ~ +125°C
PAGE 1 OF 12
www.koaspeer.com
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
TN-200
Rating Table
Nominal
Inductance Marking
(nH)
Quality Self Resonant
Factor Frequency Resistance DC Current Frequency
(typ.) (typ.) (MHz)
DC
Allowable Measuring
Inductance
Tolerance
Type
(typ.) (Ω)
(typ.) (mA)
(MHz)
KL73 1E T 1N0C
KL73 1E T 1N2C
KL73 1E T 1N5C
KL73 1E T 1N8C
KL73 1E T 2N2C
KL73 1E T 2N7C
KL73 1E T 3N3C
KL73 1E T 3N9C
KL73 1E T 4N7C
KL73 1E T 5N6
KL73 1E T 6N8
KL73 1E T 8N2
KL73 1E T 10N
KL73 1E T 12N
KL73 1E T 15N
KL73 1E T 18N
KL73 1E T 22N
KL73 1E T 27N
KL73 1J TE 1N0C
KL73 1J TE 1N2C
KL73 1J TE 1N5C
KL73 1J TE 1N8C
KL73 1J TE 2N2C
KL73 1J TE 2N7C
KL73 1J TE 3N3C
KL73 1J TE 3N9C
KL73 1J TE 4N7C
KL73 1J TE 5N6
KL73 1J TE 6N8
KL73 1J TE 8N2
KL73 1J TE 10N
KL73 1J TE 12N
KL73 1J TE 15N
KL73 1J TE 18N
KL73 1J TE 22N
KL73 1J TE 27N
KL73 1J TE 33N
KL73 1J TE 39N
1.0
1.2
12,000
0.15
700
1.5
10,000
8,000
0.20
1.8
C
2.2
(± 0.2nH)
0.25
0.30
0.50
650
2.7
3.3
600
550
500
450
6,000
10
3.9
500
4.7
5,000
5.6
6.8
4,000
3,000
1.00
350
8.2
10.0
12.0
15.0
18.0
22.0
27.0
300
250
G (± 2%)
J (± 5%)
2,500
2,000
1.50
2.00
3.00
200
150
7
1,500
200
5.00
1.0
1.2
L1
L2
L3
L4
22
27
33
39
47
56
68
82
10
12
15
H1
H2
H3
H4
H5
10
15
0.05
0.06
0.07
0.08
0.09
0.10
0.11
0.12
0.15
0.22
0.26
0.30
0.42
0.46
0.60
0.90
1.10
1.40
1.60
1.70
13,000
10,000
8,000
6,000
5,000
650
450
1.5
1.8
C
2.2
(± 0.2nH)
2.7
20
3.3
500
3.9
4.7
5.6
350
6.8
4,000
3,000
8.2
10.0
12.0
15.0
18.0
22.0
27.0
33.0
39.0
25
10
250
200
2,500
2,000
1,500
G (± 2%)
J (± 5%)
250
200
150
200
1,000
1,100
: Inductance tolerance (G or J)
PAGE 2 OF 12
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
TN-200
Rating Table Continued
Nominal
Inductance Marking
Quality Self Resonant
Factor Frequency Resistance DC Current Frequency
(typ.) (typ.) (MHz)
DC
Allowable Measuring
Inductance
Tolerance
Type
(nH)
(typ.) (Ω)
(typ.) (mA)
(MHz)
KL73 1J TE 47N
KL73 1J TE 56N
KL73 1J TE 68N
KL73 1J TE 82N
KL73 2A TE 1N0C
KL73 2A TE 1N2C
KL73 2A TE 1N5C
KL73 2A TE 1N8C
KL73 2A TE 2N2C
KL73 2A TE 2N7C
KL73 2A TE 3N3C
KL73 2A TE 3N9C
KL73 2A TE 4N7C
KL73 2A TE 5N6
KL73 2A TE 6N8
KL73 2A TE 8N2
KL73 2A TE 10N
KL73 2A TE 12N
KL73 2A TE 15N
KL73 2A TE 18N
KL73 2A TE 22N
KL73 2A TE 27N
KL73 2A TE 33N
KL73 2A TE 39N
KL73 2A TE 47N
KL73 2A TE 56N
KL73 2A TE 68N
KL73 2A TE 82N
KL73 2B TE 2N2C
KL73 2B TE 2N7C
KL73 2B TE 3N3C
KL73 2B TE 3N9C
KL73 2B TE 4N7C
KL73 2B TE 5N6
KL73 2B TE 6N8
KL73 2B TE 8N2
KL73 2B TE 10N
47.0
56.0
68.0
82.0
1.0
H6
H7
1,000
1.90
3.50
4.00
4.50
0.03
0.04
0.05
0.06
0.07
0.09
0.10
0.12
0.16
0.18
0.26
0.28
0.36
0.38
0.40
1.00
1.10
1.20
1.30
1.40
1.50
120
G (± 2%)
J (± 5%)
800
13
200
H8
700
600
100
900
H9
1.0
13,000
24
1.2
1.2
1.5
1.5
10,000
9,000
1.8
1.8
C
2.2
2.2
(± 0.2nH)
28
8,000
6,000
2.7
2.7
800
3.3
3.3
3.9
3.9
29
30
4.7
4.7
5,000
4,500
4,000
3,000
2,750
2,500
2,250
1,600
1,450
1,350
1,200
1,000
950
700
500
500
5.6
5.6
6.8
6.8
30
8.2
8.2
10.0
12.0
15.0
18.0
22.0
27.0
33.0
39.0
47.0
56.0
68.0
82.0
2.2
10.0
12.0
15.0
18.0
22.0
27.0
33.0
39.0
47.0
56.0
68.0
82.0
2N2
2N7
3N3
3N9
4N7
5N6
6N8
8N2
10N
32
30
28
450
400
G (± 2%)
J (± 5%)
22
15
300
17
15
250
150
200
800
3.50
4.00
0.07
700
600
32
38
40
42
9,000
7,000
6,000
5,000
4,500
4,000
3,500
3,000
2,900
2.7
C
1,000
900
3.3
(± 0.2nH)
0.08
0.10
0.11
0.13
0.15
0.18
0.21
3.9
4.7
500
44
5.6
6.8
G (± 2%)
J (± 5%)
40
44
8.2
800
10.0
: Inductance tolerance (G or J)
PAGE 3 OF 12
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
TN-200
Rating Table Continued
Nominal
Inductance Marking
Quality Self Resonant
Factor Frequency Resistance DC Current Frequency
(typ.) (typ.) (MHz)
DC
Allowable Measuring
Inductance
Tolerance
Type
(nH)
(typ.) (Ω)
(typ.) (mA)
(MHz)
KL73 2B TE 12N
KL73 2B TE 15N
KL73 2B TE 18N
KL73 2B TE 22N
KL73 2B TE 27N
KL73 2B TE 33N
KL73 2B TE 39N
KL73 2B TE 47N
KL73 2B TE 56N
KL73 2B TE 68N
KL73 2B TE 82N
KL73 2B TE 100
12.0
15.0
18.0
22.0
27.0
33.0
39.0
47.0
56.0
68.0
82.0
100.0
5.6
15N
18N
22N
27N
33N
39N
47N
56N
68N
82N
100.0
2,700
0.22
0.30
0.37
0.45
0.58
0.69
0.78
0.85
1.50
1.60
1.80
1.90
800
2,400
42
500
2,100
500
400
250
1,940
30
28
1,680
1,500
1,300
1,270
600
G (± 2%)
J (± 5%)
200
18
17
18
19
570
480
470
: Inductance tolerance (G or J)
4. Dimensions
Dimensions in inches (mm)
L
W
H
a
b
0402
0603
0805
1206
.039
.020
.014
.006
.010
(1.0 ± 0.1) (0.5 ± 0.05) (0.35 ± 0.05) (0.15 ± 0.1) (0.25 ± 0.1)
.063 .031 .020 .012 .012
(1.6 ± 0.2) (0.8 ± 0.1) (0.5 ± 0.1) (0.3 ± 0.1) (0.3 ± 0.1)
.079 .049 .020 .016 .012
(2.0 ± 0.2) (1.25 ± 0.2) (0.5 ± 0.1) (0.4 ± 0.2) (0.3 ± 0.2)
W
5N6
a
a
.126
.063
.024
.020
.016
L
0.2
0.1
(3.2 ± 0.2) (1.6 ± 0.2) (0.6 ± 0.1) (0.5 ± 0.2) (0.4 ±
)
H
b
b
5. Construction
Ni barrier
1 Alumina ceramic substrate 6
5
4
3
2
6
7
Solder plating
Veer hole
2 Cross electrode
7
8
3 Polyimide insulated film
4 Cu thin film coil pattern
5 Epoxy protected film
Direction mark
Marking
1
9
10
8
PAGE 4 OF 12
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
TN-200
5. Construction Continued
Ni barrier
1 Alumina ceramic substrate 6
Solder plating
Veer hole
2 Cross electrode
7
8
3 Polyimide insulated film
4 Cu thin film coil pattern
5 Epoxy protected film
Direction mark
Marking
9
10
9
10
5
7
7
3
4
5N6
6. Marking
6-1 Coating and Marking Color
Coating color:
Direction mark color:
Dark blue
Yellow
6-2 Marking Method
0402
1206
Inductance value shall have no marking.
Direction marking only.
Inductance value shall be indicated to
two letters marking of significant figures.
An alphabetical letter N shall replace
0603
position of decimal point.
Direction
mark
Inductance value shall be indicated to two
letters marking of figures and alphabet.
Direction
(Example of marking)
2N2
5N6
10
2.2nH
5.6nH
10nH
47nH
(Example of marking)
mark
5N6
L1
56
10
H6
1.0nH
5.6nH
10nH
47nH
Decimal
point
47
56
0805
Inductance value shall be indicated to two
letters marking, including decimal point.
Direction
See marking item on page 2, rating table.
(Example of marking)
mark
2.2
5.6
10
2.2nH
5.6nH
10nH
47nH
5.6
Decimal
point
47
PAGE 5 OF 12
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
TN-200
7. Characteristics
7-1 Test Condition
Unless otherwise specified, the standard range of atmospheric
conditions for marking measurements and tests is as follows:
Ambient temperature: 20 ± 15°C
Relative humidity:
65 ± 20%
If there may be any doubt on results, measurements shall be made
within the following limits:
Ambient temperature: 20 ± 2°C
Relative humidity:
65 ± 5%
7-2 Measurement Method of L and Q
Test equipment:
Fixture:
Hewlett Packard RF Impedance analyzer 4191A
Hewlett Packard Test fixture 16092A
Measuring frequency: 500 MHz/1.0nH ~ 22nH (1.0nH ~ 15nH)
200 MHz/27nH ~ 100nH (18nH ~ 47nH)
1. Perform auto-calibration to the HP4191A .275" (7 mm) unknown connector connected to
0Ω/0S/50Ω standard terminations.
2. Connected the test fixture 16092A.
Measure the open circuit admittance (Go, Bo), and the short circuit impedance (Ro, Xo).
Ro
Xo
Rx
Xx
Gm + jBm: Measured admittance [S]
Ro + jXo: Residual impedance [Ω]
Go + jBo: Stray admittance [S]
Bo
Gm + j Bm
Go
4191A
Caribration
plane
Rx + jXx: Unknown impedance [Q]
16092A Spring clip fixture
Coil
3. Set pattern up and ground side to direction mark on insulator. Measure admittance (Gm, Bm).
Chip inductor (Face up)
0402
Insulator (Teflon)
Spring clip
.118 (3.0)
.039 (1.0)
.118 (3.0)
Grand plane
See table
Terminal
Cross section of 16092A
0603 .055 (1.4)
.031 (0.8)
0805 .071 (1.8)
1206 .106 (2.7)
Dimensions of insulator (Teflon)
in inches (mm)
Thickness: .040 (1.0)
PAGE 6 OF 12
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
TN-200
4. The L and Q value shall be given the following equation. (Compensated calculation)
Gm - Go
Rx =
- Ro
2
2
(Gm - Go) + (Bm - Bo)
L: Inductance of coil
Q: Quality factor of coil
f: Measuring frequency
Bo - Bm
Xx =
- Xo
2
2
(Gm - Go) - (Bm - Bo)
Xx
2πf
Xx
Rx
Q =
L =
,
7-3 Characteristics
Item
Requirement
More than 104 MΩ
Test Method
Insulation
resistance
DC 500V, 1 minute between
both terminals and center
of reverse side.
V
More than 103 MΩ
DC 500V, 1 minute
Between both terminals and center
of protection coating.
V
Dielectric
withstanding
voltage
Without distinct damage
DC 500V, 1 minute
Between both terminals and center
of protection coating.
V
PAGE 7 OF 12
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
TN-200
7-3 Characteristics Continued
Item Requirement
Terminal
Test Method
∆ R/R: Within ± 1%
Soldered chip on wiring board A for
test is to be bent down to .079" (2 mm)
- 0603, .118" (3 mm) - 0402, 0805 and
1206 as below drawing.
strength
∆ L/L: Within ± 2%
∆ Q/Q: Within ± 20%
No mechanical damage by
cracks or stripping, etc.
(Set condition)
Dimensions in inches (mm)
Wiring board A
Chip coil
for test
Solder
Within ±2
Support
(ø5)
1.77 (45.0)
1.77 (45.0)
.786 (20)
1.97 (50)
Weight
.118
(3.0)
R230
Ohmmeter
Vibration
∆ L/L: Within ± 2%
∆ Q/Q: Within ± 20%
Without distinct damage in
appearance and construction
Inflict 2 hours in each direction of X, Y,
Z at vibration of JIS C 5025 (1978) type
A - 0603; 10 ~ 55Hz, amplitude .059"
(1.5 mm) - 0402, 0805 and 1206
Resistance to
solder heat
∆ L/L: Within ± 2%
∆ Q/Q: Within ± 20%
Without distinct damage in
appearance and construction
260 ± 5°C, 10 ± 1 second
Solderability
Terminal surface wet %:
more than 75%
230 ± 5°C, 3 ± 0.5 second
Shock
resistance
∆ L/L: Within ± 2%
∆ Q/Q: Within ± 20%
Inflict the impulse 3 times to both
directions (total 18 times) along
Without distinct damage in
appearance and construction
perpendicular axis that test condition
C of JIS C 5026 (1974) table-1 - 0603;
100G, 6 months - 0402, 0805 and 1206
PAGE 8 OF 12
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
TN-200
7-3 Characteristics Continued
Item
Requirement
Test Method
Low temperature
operation
∆ L/L: Within ± 2%
∆ Q/Q: Within ± 20%
Without distinct damage in
appearance and construction
-40°C ± 3°C, 1,000 ± 4 hours
Heat resisting
property
∆ L/L: Within ± 2%
∆ Q/Q: Within ± 20%
Without distinct damage in
appearance and construction
125°C ± 2°C, 1,000 ± 4 hours
Temperature
cycling
∆ L/L: Within ± 2%
∆ Q/Q: Within ± 20%
Without distinct damage in
appearance and construction
-40 ± 3°C, 30 minutes/125 ± 2°C,
30 minutes 100 cycles
Humidity
∆ L/L: Within ± 2%
40 ± 2°C, 90 ~ 95% RH
1,000 ± 4 hours
∆ Q/Q: Within ± 20%
Without distinct damage in
appearance and construction.
Insulation resistance:
more than 50MΩ
Resistance to
solvent
∆ L/L: Within ± 2%
∆ Q/Q: Within ± 20%
Without distinct damage in
appearance, construction
and marking
Immerse 30 ± 5 seconds in the regent
(20 ~ 25°C) of JIS K 8839 (1995)
PAGE 9 OF 12
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
TN-200
8. Packaging
8-1 Bulk Packaging
Bulk products shall be packed 1,000 pieces in a poly bag.
Marking item for bag shall be following form.
(Marking item)
(1) Type designation
(3) Quantity
(5) Manufacturer's name
(2) Nominal inductance
(4) Production lot number
8-2 Taping
The tapes for taping shall be embossed carrier tapes of .315" (8 mm) width and .157" (4 mm)
pitches. The standard quantity per reel shall be 4,000 pieces. Tapes for size 0402 (only) shall
be paper carrier tapes of .315" (8 mm) width and .079" (2 mm) pitches.
(1) Dimensions of carrier tape
.010
(0.25 ± 0.1)
.069
(1.75 ± 0.1)
.059
(1.5 ± 0.1)
.157 (4.0 ± 0.1)
D
.138
(3.5 ±
0.05)
.315
(8.0 ± 0.2)
Direction of mark
C
A
B
E
Tape running direction
Dimensions in inches (mm)
Size
A
B
C
D
E
0402
.018
.026
.045
.079
.079
(0.45 ± 0.2) (0.65 ± 0.1) (1.15 ± 0.1) (2.0 ± 0.05) (2.0 ± 0.05)
0603
0805
1206
.035
.043
.075
.079
.157
(4.0 ± 0.1)
(0.90 ± 0.1) (1.1 ± 0.15) (1.9 ± 0.15) (2.0 ± 0.01)
.037
.057
.094
.079
(2.0 ± 0.1)
.157
(4.0 ± 0.1)
(0.95 ± 0.1) (1.45 ± 0.15) (2.4 ± 0.2)
.037
.074
.137
.079
.157
(0.95 ± 0.1)
(1.9 ± 0.2)
(3.5 ± 0.2)
(2.0 ± 0.1)
(4.0 ± 0.1)
11.80 (300 ± 200
)
5.90 (150 ± 200
)
4,000 pieces
13.76 (350 ± 200
)
Top tape
Empty
Empty
Tape running direction
PAGE 10 OF 12
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
TN-200
(2) Reel dimensions
Dimensions in inches (mm)
7.00
(178 ± 2.0)
Marking
place
(Marking item)
.079
(2 ± 0.5)
(1) Type designation
(2) Nominal inductance
(3) Quantity
.511
(13 ± 0.5)
2.36
(60 ± 2.0)
(4) Production lot number
(5) Manufacturer's name
.393 (10 ± 1.5)
.448 (11.4 ± 1.5)
9. Recommended Soldering Condition
9-1 Dimensions of Standard Land
Solder resist
A
C
Dimensions in inches (mm)
Size
A
B
C
0402 - 1E .016 ~ .020
.012 ~ .020
(0.3 ~ 0.5)
.016 ~ .020
(0.4 ~ 0.5)
B
(0.4 ~ 0.5)
Chip coil
Land
0603 - 1J .031 ~ .039
.016 ~ .031
(0.4 ~ 0.8)
.016 ~ .031
(0.4 ~ 0.8)
(0.8 ~ 1.0)
0805 - 2A .047 ~ .055
.035 ~ .051
(0.9 ~ 1.3)
.016 ~ .031
(0.4 ~ 0.8)
(1.2 ~ 1.4)
1206 - 2B .079 ~ .094
.047 ~ .063
(1.2 ~ 1.6)
.016 ~ .031
(0.4 ~ 0.8)
(2.0 ~ 2.4)
9-2 Soldering Condition
Reflow soldering should be done at 240°C
within 20 seconds. Flow soldering should be
done at 260°C within 10 seconds. Please
use suitable solder quantity, too much
solder may affect performance of product.
Solder
Solder
PAGE 11 OF 12
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
TN-200
10. Recommended Washing Condition
Isopropyl alcohol and methyl alcohol used for the washing process will not affect the part performance.
Ultrasonic cleaning should be changed to condition for size of printed wiring board and
type of oscillator. Overpowering of ultrasonic cleaning will cause problems according to resonant
phenomenon. Condition of ultrasonic cleaner should be confirmed prior to use.
We recommend the following conditions:
Ultrasonic power: Within 20W/1
Cleaning times: Within 5 minutes
11. Storage
Chip inductors should not be stored under high temperature and high humidity conditions.
In particular, do not store taping where it is exposed to heat or direct sunlight. Otherwise,
the packing material may be deformed, causing problems during mounting.
PAGE 12 OF 12
■
■
■
■
■
■
Bolivar Drive
P.O. Box 547
Bradford, PA 16701
USA
814-362-5536
Fax 814-362-8883
www.koaspeer.com
AHA 6/99
相关型号：
©2020 ICPDF网 联系我们和版权申明