JT107MG18 [LGE]
Ceramics discriminator for FM receiver; 陶瓷鉴别器的FM接收器型号: | JT107MG18 |
厂家: | LGE |
描述: | Ceramics discriminator for FM receiver |
文件: | 总6页 (文件大小:144K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
http://www.luguang.cn Email: lge@luguang.cn
1. SCOPE
This specification is applied to the ceramics discriminator used with the
type JT10.7MG18 for FM receiver. Please contact us before using any
of the products in the applications not described above.
2. PART NO.:
PART NUMBER CUSTOMER PART NO SPECIFICATION NO
JT10.7MG18
3. OUTLINE DRAWING AND DIMENSIONS:
Appearance: No visible damage and dirt.
Construction: Leads are soldered on electrode and body is molded by
resin.
Dimensions:
COLOR
J10.7G
UNIT:mm
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
1
http://www.luguang.cn Email: lge@luguang.cn
4. ELECTRICAL SPECIFICATIONS:
No
4.1
Item
Requirements
Center Frequency fo (MHz)
Recovered Audio Voltage (at fo)
(mV) min
A:10.700±0.030 (RED)
4.2
4.3
4.4
60
0.9
300
Distortion (at fo)
(%) max
Recovered Audio 3dB Bandwidth
(kHz) min
Temp. Coefficient of Frequency
(ppm/℃) max
±100 (Center Frequency drift,
-10℃~+70℃)
4.5
4.6 Insulation Resistance Ri,(MΩ)min
4.7 Withstanding Voltage
100 (100V,1min)
50VDC, 1min
5. MEASUREMENT:
Measurement Conditions: Parts shall be measured under a condition
( Temp. :20±15℃,Humidity :65±20% R.H.) unless the standard
condition(Temp.:25±2℃,Humidity :65±5% R.H.) is regulated to
measure.
Test Circuit:
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
2
http://www.luguang.cn Email: lge@luguang.cn
Input Signal:
Input Level: 80dBμV
Modulation Frequency:1000Hz
Frequency Deviation: ±22.5kHz
Center Frequency(fo): Center frequency is measured under the
condition that modulated and 80dBμV input signal (center)
is supplied and varied its frequency. It is defined as the
frequency at that D.C.output voltage shall correspond to that for
0dBμV input signal.
Recovered Audio Voltage: It is defined as the recovered audio
voltage at center frequency(fo).
Distortion: It is defined as the distortion at center frequency
(fo).
Recovered Audio 3dB Bandwidth: It is defined as the difference
between the two frequencies where the recovered audio voltage
3dB from the level of center frequency(fo).
6. PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS
Performance
Requirements
No
6.1
Item
Condition of Test
Humidity
Subject the discriminator at +40±2℃ and It shall fulfill
90%-95% R.H. for 100 hours, discriminator the
shall be measured after being placed in natural specifications
conditions for 1 hour.
in Table 1.
6.2
6.3
6.4
High
Subject the discriminator to +85±5℃ for 100 It shall fulfill
Temperature hours, discriminator shall be measured after the
Exposure
Low
being placed in natural conditions for 1 hour.
specifications
in Table 1.
Subject the discriminator to –25±5℃ for 100 It shall fulfill
Temperature hours, discriminator shall be measured after the
Exposure
being placed in natural conditions for 1 hour.
specifications
in Table 1.
Temperature Subject the discriminator to -25℃ for 30 It shall fulfill
Cycling
min. followed by a high temperature of + the
85℃ for 30 min. Cycling shall be repeated 5 specifications
times. Discriminator shall be measured after in Table 1.
being placed in natural conditions for 1 hour.
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
3
http://www.luguang.cn Email: lge@luguang.cn
6. PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS
(Continued from the preceding page)
Performance
Requirements
No
6.5
Item
Condition of Test
Vibration
Subject the discriminator to vibration for 2 It shall fulfill the
hours each in x y and z axis with the specifications in
amplitude of 1.5mm, the frequency shall be Table 1.
varied uniformly between the limits of
10Hz-55Hz and then discriminator shall be
measured.
6.6
6.7
6.8
Mechanical Discriminator shall be measured after 3 times' No
visible
Shock
random dropping from the height of 100cm damage and it
on concrete floor.
shall fulfill the
specifications in
Table 1.
Resistance
Lead terminals are immersed up to 2 mm It shall fulfill the
to Soldering from discriminator’s body in soldering bath of specifications in
Heat
260 ± 5 ℃ for 5 ± 1 seconds and then Table 1.
discriminator shall be measured after being
placed in natural conditions for 1 hour
Solderability Lead terminals are immersed up to 2mm from More than 95%
discriminator’s body in soldering bath of 250 of the terminal
±5℃ for 2±0.5 sec.
surface of the
discriminator
shall be covered
with
fresh
solder.
6.9
Terminal
Strength
Force of 5N is applied to each lead in axial No
direction for 10±1 sec.
visible
damage and it
6.9.1 Terminal
Pulling
6.9.2 Terminal
Bending
When force of 5N is applied to each lead in shall fulfill the
axial direction, the lead shall folded up 90° specifications in
from the axial direction and folded back to the Table 1.
axial direction. The speed of folding shall be
each 3 seconds.
Table 1
Item
Specification after test
±30kHz max
±2dB max
Center Frequency drift
Recovered Audio Voltage drift
Note :The limits in the above table are referenced to the initial measurements.
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
4
http://www.luguang.cn Email: lge@luguang.cn
7. .REVIEW OF SPECIFICATIONS
When something gets doubtful with this specifications, we shall
jointly work to get an agreement.
8. PACKAGE
To protect the products in storage and transportation,it is
necessary to pack them(outer and inner package).On paper pack, the
following requirements are requested.
a) Dimensions and Mark
At the end of package, the warning (moisture proof, upward put)
should be stick to it.
Dimensions and Mark (see below)
NO.
1
Name
Inner Box
Box
Quantity
Notes
40
2
2
3
Package
1
4
Adhesive tape
Label
1.2m
1
5
6
Belt
2.9m
1
7
Certificate of approval
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
5
http://www.luguang.cn Email: lge@luguang.cn
b) Section of package
Package is made of corrugated paper with thickness of
0.8cm.Package has 2 inner boxes, each has 20 inner boxes (each box for
plastic bag).
c) Quantity of package
Per plastic bag
Per inner box
Per package
500 pieces
3 plastic bag
40 inner boxes(60000 pieces of
piezoelectric ceramic part )
d) Inner box Dimensions
1.UNIT: mm
1
2
3
Label
QC Label
Inner Box
Pars shall be packaged in box with hold down tape upside. Part No.,
quantity and lot No.
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
6
相关型号:
©2020 ICPDF网 联系我们和版权申明