LTCS107MA5 [LGE]
ceramic fliter; 陶瓷Fliter型号: | LTCS107MA5 |
厂家: | LGE |
描述: | ceramic fliter |
文件: | 总7页 (文件大小:282K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
http://www.luguang.cn Email: lge@luguang.cn
1 SCOPE
This specification shall cover the characteristics of the ceramic
fliter with the
type LTCS10.7MA5. The LTCS10.7MA5 filters are small, high performance and very
thin (1.4mm) chip devices consisting of 2 ceramic elements for communication
equipment. They are designed on MgTiO3 ceramic cap package.
2 PART NO.
PART NUMBER
LTCS10.7MA5
CUSTOMER PART NO.
SPECIFICATION NO.
3 OUTLINE DRAWING AND STRUCTURE
3.1 Appearance
No visible damage and dirt.
3.2 Except the chip(ceramic element, ceramic base, capacitance slice), the materials
don’t contain lead.
3.3 Dimensions
A5
*
Input electrode marker
(1) :Input
(2) :Ground
(3) :Float(signal line)
(4) :Output
(*) :Range of frequency
1
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
http://www.luguang.cn Email: lge@luguang.cn
4 ELECTRICAL SPECIFICATIONS
4.1 RATING
Items
Content
50 (DC,1min)
100 (100V,1min)
-20~+80
Withstanding Voltage (V)
Insulation Resistance Ri,(MΩ)min.
Operating Temperature Range (℃)
Storage Temperature Range (℃)
-40~+85
4.2 ELECTRICAL SPECIFICATIONS
Items
Content
A:10.700±0.030
B:10.670±0.030
C:10.730±0.030
D:10.640±0.030
E:10.760±0.030
280±50
Center Frequency(fo) (MHz)*
3dB Bandwidth(kHz)
20dB Bandwidth(kHz) max
590
Insertion Loss (dB) (at minimum loss point)
Ripple (dB) max (within 3dB Bandwidth)
Spurious Response (dB) min(9MHz-12MHz)
Input/Output Impedance(Ω)
3.0±2.0
1.0
30
330
5 TEST
5.1 Test Conditions
Parts shall be tested under a condition (Temperature:+20℃±15℃,Humidity:65%
±20%R.H.)unless the standard condition(Temperature:+25℃±3℃,Humidity:65%±5%
R.H.) is regulated to test.
5.2 Test Circuit
R1=280Ω(1±5%,) R2=330Ω(1±5%,) Rg=50Ω
C2=10pF(Including stray capacitance
and capacitance of RF Voltmeter)
S.S.G:Output Voltmeter
①:Input ②:Ground ③:Float ④:Output
2
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
http://www.luguang.cn Email: lge@luguang.cn
6 PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS
Performance
NO.
6.1
Item
Condition of Test
Requirment
Low Temp Stored in -40℃±3℃ for 96h,and left at room
Meet Table 1
Storage
temp. for 1h before measurement.
High Temp Stored in 85℃±2℃ for 96h,and left at room
6.2
Meet Table 1
Meet Table 1
Storage
temp. for 1h before measurement.
Stored at 40℃±2℃,in 90%~95%R.H. for 96h,
and left at room temp. for 1h before measurement
After temp. cycling of -40℃(30 minutes) to +85℃
(30min) was performed 5 times, filter shall be
measured after being placed in natural condition for
6.3 Humidity
Thermal
6.4
Meet Table 1
Shock
1h.
Passed through the reflow oven under the following
condition for 2 times, and left at room temp. for
24h before measurement.
Soldering
Test
Temp. at the surface of the substrate
Time
60s±10s
20s-40 s
10s±1s
6.5
Meet Table 1
Preheat 150℃±5℃
≥200℃
240℃±5℃
Soldering
The terminals
Dipped in 235℃±5℃ solder bath for 3s±0.5s shall be at least
6.6 Solderability
with rosin flux.
95% covered
by solder
Free drop to the wood plate from the height of 70
cm for 3 times.
Apply the vibration of sweep frequency 10 to
55Hz/minutes, amplitude 1.5mm, duration 2h in Meet Table 1
each direction of 3 planes.
6.7 Drop test
6.8 Vibration
Meet Table 1
Mount on a glass-epoxy board( width=50 mm,
thickness=1.6mm),then
bend
it
to 1mm
displacement(velocity 1mm/s) and keep it for 5s.
Press
Mechanical
damage such
as break shall
not occur
20
Board
6.9
Press Head
Bending
Support bar
D.U.T
5
45± 2
45± 2
3
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
http://www.luguang.cn Email: lge@luguang.cn
Table 1
Item
Specification after test
Insertion Loss Drift (dB) max
3dB Bandwidth Drift (kHz) max
20dB Bandwidth Drift (kHz) max
±2
±25
±60
Note:The limits in the above table are referenced to the initial measurements.
7
RECOMMENDED LAND PATTERN AND REFLOW SOLDERING
STANDARD CONDITIONS
7.1 Recommended land pattern
(4)
(1)
(3)
(2)
7.2 Recommended reflow soldering standard conditions
℃
within 10s
℃
Pre-heating
within
within
80s-120s.
20s-40s
4
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
http://www.luguang.cn Email: lge@luguang.cn
8 PACKAGE
To protect the products in storage and transportation,it is necessary to pack them
(outer and inner package).On paper pack, the following requirements are requested.
8.1 Dimensions and Mark
At the end of package, the warning (moisture proof, upward put) should be stick
to it.
Dimensions and Mark (see below)
1 Package
2 Certificate ofapproval
3 Label
4 Tying
5 Adhesive tape
6 Belt Box
7 Inner
UNIT:mm
8.2 Section of package
Package is made of corrugated paper with thickness of 0.8cm.Package has 10 inner
boxes, each box has 1reel (each reel for plastic bag).
8.3 Quantity of package
Per plastic reel
Per inner box
Per package
4000 pieces of piezoelectric ceramic part
1 reel
10 inner boxes
(40000 pieces of piezoelectric ceramic part )
5
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
http://www.luguang.cn Email: lge@luguang.cn
8.4 Reel
φ
max
8.5 Packing Method Sketch Map
Leader
200mm Max
Blank Pocket
10 Pitches
Blank Pocket
10 Pitches
Loaded Pocket
8.6 Test Condition Of Peeling Strength
T o p T a p e
1 0 ° M a x
C a rrie r T a p e
6
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
http://www.luguang.cn Email: lge@luguang.cn
9 EIAJ Monthly Code
2003 / 2005 / 2007 / 2009
2004 / 2006 / 2008 / 2010
MONTH
JAN
CODE
MONTH
JAN
CODE
A
B
C
D
E
F
N
P
FEB
FEB
MAR
APR
MAY
JUN
MAR
APR
MAY
JUN
Q
R
S
T
JUL
G
H
J
JUL
U
V
W
X
Y
AUG
SEP
AUG
SEP
OCT
NOV
K
L
OCT
NOV
10 OTHER
10.1 Caution of use
10.1.1 Do not use this product with bend. Please don’t apply excess mechanical
stress to the component and terminals at soldering.
10.1.2 The component may be damaged when an excess stress will be applied.
10.1.3 This specification mentions the quality of the component as a single unit.
Please insure the component is thoroughly evaluated in your application circuit.
10.2 Notice
10.2.1 Please return one of this specification after your signature of acceptance.
10.2.2 When something gets doubtful with this specifications, we shall jointly work
to get an agreement.
7
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD
.
相关型号:
LTCT1991CDD#TRPBF
IC OP-AMP, 250 uV OFFSET-MAX, 0.56 MHz BAND WIDTH, PDSO10, 3 X 3 MM, 0.80 MM HEIGHT, LEAD FREE, PLASTIC, MO-299WEED-2, DFN-10, Operational Amplifier
Linear
©2020 ICPDF网 联系我们和版权申明