ZTTCV30.0MX [LGE]

Ceramic Resonator; 陶瓷谐振器


型号：	ZTTCV30.0MX
厂家：	LGE
描述：	Ceramic Resonator 陶瓷谐振器陶瓷谐振器
文件：	总8页 (文件大小：368K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

ZTTCV30.0MX

Ceramic Resonator

1. SCOPE

This specification shall cover the characteristics of the ceramic

resonator with the type ZTTCV30.0MX

2. PART NO.:

PART NUMBER CUSTOMER PART NO SPECIFICATION NO

ZTTCV30.0MX

3. OUTLINE DRAWING AND DIMENSIONS:

Appearance: No visible damage and dirt.

Dimensions:

30.0M

UINT: mm

SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD

ZTTCV30.0MX

Ceramic Resonator

4. ELECTRICAL SPECIFICATIONS:

Requirements

Item

4.1 Oscillation Frequency Fosc（MHz）

Frequency Accuracy (%)

30.0

±0.5

4.2 Resonant Impedance Ro (Ω)max

4.3

Temperature Coefficient of

Oscillation Frequency (%) max

Withstanding Voltage

Rating Voltage U_R(V)

(1) D.C. Voltage

±0.3 (Oscillation Frequency

drift -20℃ to +80℃)

50 VDC, 1 min

4.4

4.5

6 VDC.

15 Vp-p.

(2) A.C. Voltage

4.6

100 ( 100V, 1min)

Insulation Resistance Ri（, MΩ）min

4.7

4.8

4.9

Operating Temperature (℃)

-40～+85

-55～+85

±0.3 (For 10 years)

Storage Temperature

(℃)

Aging Rate (%) max

5. MEASUREMENT:

Measurement Conditions: Parts shall be measured under a condition

( Temp. ：20±15℃,Humidity ：65±20% R.H.) unless the standard

condition(Temp.：25±3℃,Humidity ：65±5% R.H.) is regulated to

measure.

Test Circuit:

IC：1/6TC74HCU04×2

X：CERAMIC RESONATOR

C1=C2: 15PF

SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD

ZTTCV30.0MX

Ceramic Resonator

6.PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS

Item

Condition of Test

Performance

Requirements

6.1 Humidity

Keep the resonator at 40±2℃ and 90-95% RH It shall fulfill

for 96±4 hours. Then Release the resonator into the

the room Condition for 1 hour prior to the specifications

Measurement.

in Table 1.

6.2 Vibration

Subject the resonator to vibration for 2 hours It shall fulfill

each in x、y and z axis With the amplitude of the

1.5mm, the frequency shall be varied uniformly specifications

between the limits of 10 Hz—55Hz.

in Table 1.

6.3 Mechanical

Shock

Drop the resonator randomly onto a wooden It shall fulfill

floor from the height of 100cm 3 times.

the

specifications

in Table 1.

6.4 Soldering

Test

Passed through the re-flow oven under the It shall fulfill

following condition and left at room the

temperature for 1 hour before measurement.

specifications

in Table 1.

Temperature at the surface of the

substrate

Time

Preheat 150±5℃

60±10

sec

Peak

240±5℃

10±3 sec

6.5 Solder

Ability

Dipped in 230±5℃ solder bath for 3±0.5 sec The terminals

seconds with rosin flux (25wt% ethanol shall be at

solution.)

least

covered

solder.

95%

6.6 High

Subject the resonator to 80±5℃ for 96 hours, It shall fulfill

Temperature then release the resonator into the room the

Exposure

6.7 Low

conditions for 1 hour prior to the measurement. specifications

in Table 1.

Subject the resonator to -20±5℃ for 96 hours, It shall fulfill

Temperature then release the resonator into the room the

Exposure

conditions for 1 hour prior to the measurement. specifications

in Table 1.

SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD

ZTTCV30.0MX

Ceramic Resonator

6.PHYSICAL AND ENVIRONMENAL CHARACTERISICS

(Continued from the preceding page)

Item

Condition of Test

Performance

Requirements

6.8 Temperature

Cycling

Subject the resonator to -40℃ for 30 It shall fulfill the

min. followed by a high temperature of specifications

85℃ for 30 min.

Table 1.

Cycling shall be repeated 5 times with a

transfer time of 15 sec. At the room

temperature for 1 hour prior to the

measurement.

Mount

glass-epoxy

board

6.9 Board

Bending

Mechanical damage

such as breaks shall

not occur.

(Width=40mm,thickness=1.6mm),then bend it

to 1mm displacement and keep it for 5 seconds.

(See the following figure)

PRESS

PRESS HEAD

SUPPORT BAR

TABLE 1

Item

Specification

Oscillation Frequency Change

△Fosc/Fosc (%) max

Resonant Impedance Change

△Ro(Ω)max

±0.3

±10

Note: The limits in the above table are referenced to the initial measurements.

SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD

ZTTCV30.0MX

Ceramic Resonator

7. REVIEW OF SPECIFICATIONS

When something gets doubtful with this specifications, we shall

jointly work to get an agreement.

8. RECOMMENDED LAND PATTERN AND REFLOW SOLDERING

STANDARD CONDITIONS

8.1Recommended land pattern

DIMENSIONS (mm)

T₁

T₂

T₃

W₁

1.0±0.2

0.7±0.2

1.5±0.2

4.1±0.2

8.2Recommended reflow soldering standard conditions

within 10 sec

℃

Pre-heating

within

80-120sec.

20-40sec

SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD

ZTTCV30.0MX

Ceramic Resonator

9. PACKAGE

To protect the products in storage and transportation，it is

necessary to pack them（outer and inner package）.On paper pack, the

following requirements are requested.

a) Dimensions and Mark

At the end of package, the warning (moisture proof, upward put)

should be stick to it.

Dimensions and Mark (see below)

NO.

Name

Package

Certificate of approval

Label

Quantity

Notes

Tying

Adhesive tape

Belt

1.2m

2.9m

Inner Box

b) Section of package

Package is made of corrugated paper with thickness of

0.8cm.Package has 10 inner boxes, each box has 1 reel(each reel for

plastic bag)

SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD

ZTTCV30.0MX

Ceramic Resonator

c) Quantity of package

Per plastic reel

4000 pieces of piezoelectric ceramic part

Per inner box

1 reel

Per package

10 inner boxes（40000 pieces of piezoelectric

ceramic part ）

d) Inner Packing Dimensions

Label

QC Label

Inner Box

1.UNIT: mm

Pars shall be packaged in box with hold down tape upside. Part

No., quantity and lot No.

8.5Reel

Dimensions

Unit：mm

φA

φB

Pieces per reel Carrier tape size

330±3 80min 16.4min 22.4max

4000typ.

SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD

ZTTCV30.0MX

Ceramic Resonator

8.6Taping Dimensions

8.7Packing Method Sketch Map

Blank Pocket

10 Pitches

Blank Pocket

10 Pitches

Leader

200mmMax

Loaded Pocket

8.8Test Condition Of Peeling Strength

T o p T a p e

1 0 ° M a x

C a rrie r T a p e

SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD