HW005A0F1-SZ中文资料_数据手册_规格书

Data Sheet

May 16, 2008

HW/HC004/005/006 Series DC-DC Converter Power Modules:

18-36V & 36-75Vdc Input; 1.0V-5Vdc Output; 4A-6A Output Current

RoHS Compliant

Features

Compliant to RoHS EU Directive 2002/95/EC (-Z

versions)

Compliant to ROHS EU Directive 2002/95/EC with

lead solder exemption (non-Z versions)

Delivers up to 6A Output current

5V (4A), 3.3V (5A), 2.5V – 1.0V (6A each)

High efficiency – 89% at 5.0V full load

Low Output voltage- supports migration to future IC

supply voltages down to 1.0V

Low output ripple and noise

Applications

Small Size and low profile

Wireless Networks

47.2mm x 29.5mm x 8.5mm

(1.86 x 1.16 x 0.335 in)

Distributed power architectures

Optical and Access Network Equipment

Enterprise Networks

Surface mount or Through hole (TH)

Remote On/Off

Latest generation IC’s (DSP, FPGA, ASIC)

and Microprocessor powered applications

Output overcurrent/Over voltage protection

Over temperature protection

Single Tightly regulated output

Output voltage adjustment trim ±10%

Wide operating temperature range (-40°C to 85°C)

Options

Remote On/Off logic (positive or negative)

Surface Mount (-S Suffix)

Meets the voltage insulation requirements for ETSI

300-132-2 and complies with and is Licensed for

Basic Insulation rating per EN 60950

Additional Vout+ pin (-3 Suffix)

CE mark meets 73/23/EEC and 93/68/EEC

directives^§

UL* 60950-1Recognized, CSA^†C22.2 No. 60950-1-

03 Certified, and VDE^‡0805:2001-12 (EN60950-1)

Licensed

ISO** 9001 and ISO 14001 certified manufacturing

facilities

Description

The HW/HC series power modules are isolated dc-dc converters that operate over a wide input voltage range of 18

to 36 Vdc (HC) or 36 to 75 Vdc (HW) and provide one precisely regulated output. The output is fully isolated from

the input, allowing versatile polarity configurations and grounding connections. The modules exhibit high efficiency,

e.g. typical efficiency of 87% 3.3V/5A, 86% at 2.5V/6A. Built-in filtering for both input and output minimizes the need

for external filtering. These open frame modules are available either in surface-mount (-S) or in through-hole form.

*

UL is a registered trademark of Underwriters Laboratories, Inc.

CSA is a registered trademark of Canadian Standards Association.

VDE is a trademark of Verband Deutscher Elektrotechniker e.V.

†

‡

** ISO is a registered trademark of the International Organization of Standards

Document No: DS03-017 ver.1.21

PDF No: hw-hc_4-6a.pdf

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are

absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in

excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for

extended periods can adversely affect the device reliability.

Parameter

Device

HC

Symbol

V_IN

Min

-0.3

-40

Max

50

Unit

Vdc

°C

Input Voltage

Continuous

HW

All

V_IN

80

Transient (100ms)

V_{IN, trans}

T_A

100

85

Operating Ambient Temperature

(see Thermal Considerations section)

Storage Temperature

I/O Isolation Voltage (100% factory tested)

All

T_stg

-55

125

°C

2250

Vdc

⎯

Electrical Specifications

Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature

conditions.

Parameter

Device

Symbol

Min

Typ

Max

Unit

Operating Input Voltage

HC

HW

HC

V_IN

18

36

24

54

36

75

Vdc

Adc

Maximum Input Current

(V_IN=0V to 75V, I_O=I_{O, max}

I_IN,max

1.75

)

HW

All

I_IN,max

I²t

0.85

1

Adc

A²s

Inrush Transient

Input Reflected Ripple Current, peak-to-peak

(5Hz to 20MHz, 12μH source impedance; V_IN=0V to

75V, I_O= I_Omax; see Figure 9)

All

5

mAp-p

dB

Input Ripple Rejection (120Hz)

50

EMC, EN55022

See EMC Considerations section

CAUTION: This power module is not internally fused. An input line fuse must always be used.

This power module can be used in a wide variety of applications, ranging from simple standalone operation to being

part of complex power architecture. To preserve maximum flexibility, internal fusing is not included; however, to

achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-

acting fuse with a maximum rating of 3A (see Safety Considerations section). Based on the information provided in

this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be

used. Refer to the fuse manufacturer’s data sheet for further information.

LINEAGE POWER

2

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Electrical Specifications (continued)

Parameter

Device

Symbol

Min

Typ

Max

Unit

5V, 3.3V

2.5V, 2.0V,

1.8V, 1.5V

Output Voltage Set-point

V_{O, set}

-1.0

+1.0

% V_{O, nom}

⎯

(V_IN=V_IN,nom, I_O=I_{O, max}, T_ref=25°C)

Output Voltage

1.2V, 1.0V

All

V_{O, set}

V_O

-1.25

-3.0

+1.25

+3.0

% V_{O, nom}

⎯

(Over all operating input voltage, resistive load,

and temperature conditions until end of life)

Adjustment Range

All

V_O

-10.0

+10.0

% V_{O, nom}

Selected by external resistor

Output Regulation

Line (V_IN=V_{IN, min}to V_{IN, max}

Load (I_O=I_{O, min}to I_{O, max}

Temperature (T_ref=T_{A, min}to T_{A, max}

Output Ripple and Noise on nominal output

(V_IN=V_{IN, nom}and I_O=I_{O, min}to I_{O, max}

)

All

10

15

mV

%

⎯

)

1.00

)

RMS (5Hz to 20MHz bandwidth)

All

8

15

mV_rms

⎯

Peak-to-Peak (5Hz to 20MHz bandwidth)

External Capacitance

All

25

50

mV_pk-pk

⎯

C_{O, max}

470

μF

⎯

Output Current

5V

I_o

0

4.0

5.0

Adc

3.3V

2.5V, 2.0,

1.8V, 1.5V,

1.2V, 1.0V

I_o

0

6.0

Adc

Output Current Limit Inception

( Hiccup Mode )

5V

I_{O, lim}

6.5

7

Adc

⎯

3.3V

2.5V, 2.0V,

1.8V, 1.5V,

1.2V, 1.0V

I_{O, lim}

8.5

Adc

⎯

Output Short-Circuit Current

5V

I_{O, s/c}

2.4

A rms

⎯

(V_O≤250mV) ( Hiccup Mode )

3.3V

2.5V, 2.0V,

1.8V, 1.5V,

1.2V, 1.0V

I_{O, s/c}

2.8

A rms

⎯

LINEAGE POWER

3

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Electrical Specifications (continued)

Parameter

Device

HW 5V

Symbol

Min

⎯

Typ

89.0

87.0

86.0

82.0

80.0

77.0

75.0

88.0

86.0

300

Max

⎯

Unit

%

η

Efficiency

HW 3.3V

HW 2.5V

HW 2.0V

HW 1.8V

HW 1.5V

HW 1.2V

HW 1.0V

HC 5V

%

V_IN=V_{IN, nom}, T_A=25°C

I_O=I_{O, max ,}V_O= V_O,set

η

%

η

%

η

%

η

%

η

%

η

%

η

%

HC 3.3V

All HW

η

%

Switching Frequency

f_sw

kHz

All HC

380

Dynamic Load Response

5V, 3.3V

V_pk

100

80

mV

(ΔIo/Δt=1A/μs; V_in=V_in,nom; T_A=25°C)

⎯

2.5V, 2.0V,

1.8V, 1.5V,

1.2V, 1.0V

Load Change from Io= 50% to 75% of Io,max:

Peak Deviation

Settling Time (Vo<10% peak deviation)

All

t_s

100

⎯

μs

Dynamic Line Response

(ΔV_in/ Δt≤0.5V/μs; V_in=V_in,nom; T_A=25°C)

%Vo,

set

Peak Deviation

All

V_pk

t_s

0.6

2

⎯

Settling Time (Vo<10% peak deviation)

150

1000

μs

Isolation Specifications

Parameter

Symbol

Min

⎯

Typ

200

⎯

Max

Unit

pF

Isolation Capacitance

Isolation Resistance

C_iso

R_iso

⎯

10

MΩ

General Specifications

Parameter

Min

Typ

Max

Unit

Calculated MTBF (for HW005A0F1-S in accordance with Lucent

RIN 6: I_O=80% of I_{O, max}, T_A=25°C, airflow=1m/s)

>4,000,000

13

Hours

g (oz.)

Weight

⎯

LINEAGE POWER

4

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Feature Specifications

Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature

conditions. See Feature Descriptions for additional information.

Parameter

Device

Symbol

Min

Typ

Max

Unit

Remote On/Off Signal Interface

(V_IN=V_{IN, min}to V_{IN, max}; open collector or equivalent,

Signal referenced to V_IN-terminal)

Negative Logic: device code suffix “1”

Logic Low = module On, Logic High = module Off

Positive Logic: No device code suffix required

Logic Low = module Off, Logic High = module On

Logic Low Specification

Remote On/Off Current – Logic Low

On/Off Voltage:

All

I_on/off

0.15

1.0

mA

⎯

Logic Low

All

V_on/off

I_on/off

0.0

⎯

1.2

15

10

V

⎯

5.8

⎯

Logic High – (Typ = Open Collector)

Logic High maximum allowable leakage current

Turn-On Delay and Rise Times

μA

⎯

(I_O=I_{O, max}

)

T_delay

T_rise

100

40

ms

⎯

5V, 3.3V

T_delay= Time until V_O= 10% of V_O,setfrom either

application of Vin with Remote On/Off set to On or

operation of Remote On/Off from Off to On with Vin

already applied for at least one second.

2.5V, 2.0V,

1.8V, 1.5V,

1.2V, 1.0V

T_delay

12

3

ms

⎯

T_rise= time for V_Oto rise from 10% of V_O,setto 90%

of V_O,set

.

T_rise

5V

V_{O, limit}

7.0

4.6

3.5

3.2

2.8

2.5

2.0

1.8

⎯

V

⎯

Output Overvoltage Protection^#

3.3V

2.5V

2.0V

1.8V

1.5V

1.2V

1.0V

All

V

⎯

Values are the same for HW and HC codes

V

⎯

V

⎯

V

⎯

V

⎯

V

⎯

Overtemperature Protection

T_ref

125

°C

(See Feature Descriptions)

Input Undervoltage Lockout

Turn-on Threshold

All HW

All HC

33

30

17

15

36

⎯

18

V

⎯

27

Turn-off Threshold

Turn-on Threshold

⎯

Turn-off Threshold

13.5

⎯

# More accurate Overvoltage protection can be accomplished externally by means of the remote On/Off pin.

LINEAGE POWER

5

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Characteristic Curves

The following figures provide typical characteristics for the HW004A0A (5.0V, 4A) at 25ºC. The figures are identical

for either positive or negative Remote On/Off logic.

90

88

86

84

82

80

78

76

74

72

70

5

4

3

2

1

0

V_I=36V

V_I= 54V

V_I= 75V

3.0 m/s (600 ft./min.)

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

NATURAL CONVECTION

0

10

20

30

40

50

60

70

80

90

100 110

0

1

2

3

4

OUTPUT CURRENT, I_O(A)

AMBIENT TEMPERATURE, T_A^OC

Figure 1. Converter Efficiency versus Output Current

Figure 4. Derating Output Current versus Local

Ambient Temperature and Airflow

TIME, t (20ms/div)

TIME, t (1μs/div)

Figure 2. Typical Output Ripple and Noise.

Figure 5. Typical Start-Up with application of Vin.

TIME, t (20ms/div)

TIME, t (50μs/div)

Figure 3. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

Figure 6. Typical Start-Up Using Remote On/Off,

negative logic version shown.

LINEAGE POWER

6

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Characteristic Curves (continued)

The following figures provide typical characteristics for the HW005A0F (3.3V, 5A) at 25ºC. The figures are identical

for either positive or negative Remote On/Off logic.

90

88

86

84

82

80

78

76

74

72

70

6

5

4

3

2

1

0

V_I=36V

V_I= 54V

V_I= 75V

3.0 m/s (600 ft./min.)

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

NATURAL CONVECTION

0

10

20

30

40

50

60

70

80

90

100 110

0

1

2

3

4

5

OUTPUT CURRENT, I_O(A)

AMBIENT TEMPERATURE, T_A^OC

Figure 7. Converter Efficiency versus Output Current

Figure 10. Derating Output Current versus Local

Ambient Temperature and Airflow

TIME, t (20ms/div)

TIME, t (1μs/div)

Figure 8. Typical Output Ripple and Noise.

Figure 11. Typical Start-Up with application of Vin.

TIME, t (20ms/div)

TIME, t (50μs/div)

Figure 9. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

Figure 12. Typical Start-Up Using Remote On/Off,

negative logic version shown.

LINEAGE POWER

7

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Characteristic Curves (continued)

The following figures provide typical characteristics for the HW006A0G (2.5V, 6A) at 25ºC. The figures are identical

for either positive or negative Remote On/Off logic.

88

86

84

82

80

78

76

74

72

70

68

7

6

5

4

3

2

1

0

V_I= 36V

V_I= 54V

V_I= 75V

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

NATURAL CONVECTION

0

1

2

3

4

5

6

0

10

20

30

40

50

60

70

80

90

100 110

OUTPUT CURRENT, I_O(A)

AMBIENT TEMPERATURE, T_A^OC

Figure 13. Converter Efficiency versus Output Current. Figure 16. Derating Output Current versus Local

Ambient Temperature and Airflow.

TIME, t (5ms/div)

TIME, t (1μs/div)

Figure 14. Typical Output Ripple and Noise.

Figure 17. Typical Start-Up with application of Vin.

TIME, t (5ms/div)

TIME, t (50μs/div)

Figure 15. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

Figure 18. Typical Start-Up Using Remote On/Off,

negative logic version shown.

LINEAGE POWER

8

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Characteristic Curves (continued)

The following figures provide typical characteristics for the HW006A0D (2.0V, 6A) at 25ºC. The figures are identical

for either positive or negative Remote On/Off logic.

88

86

84

82

80

78

76

74

72

70

68

7

6

5

4

3

2

1

0

V_I= 36V

V_I= 54V

V_I= 75V

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

NATURAL CONVECTION

0

1

2

3

4

5

6

0

10

20

30

40

50

60

70

80

90

100 110

OUTPUT CURRENT, I_O(A)

AMBIENT TEMPERATURE, T_A^OC

Figure 13. Converter Efficiency versus Output

Current.

Figure 16. Derating Output Current versus Local

Ambient Temperature and Airflow

TIME, t (5ms/div)

TIME, t (1μs/div)

Figure 14. Typical Output Ripple and Noise.

Figure 17. Typical Start-Up with application of Vin.

TIME, t (5ms/div)

TIME, t (50μs/div)

Figure 15. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

Figure 18. Typical Start-Up Using Remote On/Off,

negative logic version shown.

LINEAGE POWER

9

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Characteristic Curves (continued)

The following figures provide typical characteristics for the HW006A0Y (1.8V, 6A) at 25ºC. The figures are identical

for either positive or negative Remote On/Off logic.

7

6

5

4

3

2

1

0

86

84

82

80

78

76

74

72

70

68

66

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

V_I= 36V

V_I= 54V

V_I= 75V

NATURAL CONVECTION

0

10

20

30

40

50

60

70

80

90

100 110

0

1

2

3

4

5

6

OUTPUT CURRENT, I_O(A)

AMBIENT TEMPERATURE, T_A^OC

Figure 25. Converter Efficiency versus Output

Current

Figure 28. Derating Output Current versus Local

Ambient Temperature and Airflow

TIME, t (5ms/div)

TIME, t (1μs/div)

Figure 26. Typical Output Ripple and Noise.

Figure 29. Typical Start-Up with application of Vin.

TIME, t (5ms/div)

TIME, t (50μs/div)

Figure 27. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

Figure 30. Typical Start-Up Using Remote On/Off,

negative logic version shown.

LINEAGE POWER

10

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Characteristic Curves (continued)

The following figures provide typical characteristics for the HW006A0M (1.5V, 6A) at 25ºC. The figures are identical

for either positive or negative Remote On/Off logic.

86

84

82

80

78

76

74

72

70

68

66

7

6

5

4

3

2

1

0

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

V_I= 36V

V_I= 54V

V_I= 75V

NATURAL CONVECTION

0

1

2

3

4

5

6

0

10

20

30

40

50

60

70

80

90

100 110

OUTPUT CURRENT, I_O(A)

AMBIENT TEMPERATURE, T_A^OC

Figure 31. Converter Efficiency versus Output

Current.

Figure 34. Derating Output Current versus Local

Ambient Temperature and Airflow

TIME, t (5ms/div)

TIME, t (1μs/div)

Figure 32. Typical Output Ripple and Noise.

Figure 35. Typical Start-Up with application of Vin.

TIME, t (5ms/div)

TIME, t (50μs/div)

Figure 33. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

Figure 36. Typical Start-Up Using Remote On/Off,

negative logic version shown.

LINEAGE POWER

11

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Characteristic Curves (continued)

The following figures provide typical characteristics for the HW006A0P (1.2V, 6A) at 25ºC. The figures are identical

for either positive or negative Remote On/Off logic.

80

78

76

74

72

70

68

66

64

62

60

7

6

5

4

3

2

1

0

V_I= 36V

V_I= 54V

V_I= 75V

3.0 m/s (600 ft./min.)

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

NATURAL CONVECTION

0

1

2

3

4

5

6

0

10

20

30

40

50

60

70

80

90

100 110

OUTPUT CURRENT, I_O(A)

AMBIENT TEMPERATURE, T_A^OC

Figure 37. Converter Efficiency versus Output

Current.

Figure 40. Derating Output Current versus Local

Ambient Temperature and Airflow

TIME, t (5ms/div)

TIME, t (1μs/div)

Figure 38. Typical Output Ripple and Noise.

Figure 41. Typical Start-Up with application of Vin.

TIME, t (5ms/div)

TIME, t (50μs/div)

Figure 39. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

Figure 42. Typical Start-Up Using Remote On/Off,

negative logic version shown.

LINEAGE POWER

12

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Characteristic Curves (continued)

The following figures provide typical characteristics for the HW006A0S1R0 (1.0V, 6A) at 25ºC. The figures are

identical for either positive or negative Remote On/Off logic.

80

78

76

74

72

70

68

66

64

62

60

7

6

5

4

3

2

1

0

3.0 m/s (600 ft./min.)

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

VI = 36V

VI = 54V

VI = 75V

NATURAL CONVECTION

0

1

2

3

4

5

6

0

10

20

30

40

50

60

70

80

90

100 110

OUTPUT CURRENT, I_O(A)

AMBIENT TEMPERATURE, T_A^OC

Figure 43. Converter Efficiency versus Output

Current.

Figure 46. Derating Output Current versus Local

Ambient Temperature and Airflow.

TIME, t (5ms/div)

TIME, t (1μs/div)

Figure 44. Typical Output Ripple and Noise.

Figure 47. Typical Start-Up with application of Vin.

TIME, t (5ms/div)

TIME, t (50μs/div)

Figure 45. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

Figure 48. Typical Start-Up Using Remote On/Off,

negative logic version shown.

LINEAGE POWER

13

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Characteristic Curves (continued)

The following figures provide typical characteristics for the HC004A0A (5.0V, 4A) at 25ºC. The figures are identical for

either positive or negative Remote On/Off logic.

5

4

3

2

3.0 m/s (600 ft./min.)

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

Natural Convection

1

0

10

20

30

40

50

60

70

80

90

100 110

OUTPUT CURRENT, I_O(A)

AMBIENT TEMPERATURE, T_A^OC

Figure 49. Converter Efficiency versus Output

Current.

Figure 52. Derating Output Current versus Local Ambient

Temperature and Airflow.

TIME, t (20ms/div)

TIME, t (1μs/div)

Figure 50. Typical Output Ripple and Noise.

Figure 53. Typical Start-Up with application of Vin.

TIME, t (20ms/div)

TIME, t (50μs/div)

Figure 51. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

Figure 54. Typical Start-Up Using Remote On/Off,

negative logic version shown.

LINEAGE POWER

14

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Characteristic Curves (continued)

The following figures provide typical characteristics for the HC005A0F (3.3V, 5A) at 25ºC. The figures are identical for

either positive or negative Remote On/Off logic.

6

5

4

3

3.0 m/s (600 ft./min.)

2

2.0 m/s (400 ft./min.)

1.0 m/s (200 ft./min.)

1

Natural Convection

0

10

20

30

40

50

60

70

80

90

100 110

OUTPUT CURRENT, I_O(A)

AMBIENT TEMPERATURE, T_A^OC

Figure 55. Converter Efficiency versus Output

Current.

Figure 58. Derating Output Current versus Local

Ambient Temperature and Airflow.

TIME, t (20ms/div)

TIME, t (1μs/div)

Figure 56. Typical Output Ripple and Noise.

Figure 59. Typical Start-Up with application of Vin.

TIME, t (20ms/div)

TIME, t (50μs/div)

Figure 57. Transient Response to Dynamic Load

Change from 50% to 75% to 50% of full load.

Figure 60. Typical Start-Up Using Remote On/Off,

negative logic version shown.

LINEAGE POWER

15

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Test Configurations

Design Considerations

CURRENT PROBE

Vin+

TO OSCILLOSCOPE

Input Source Impedance

L_TEST

The power module should be connected to a low

ac-impedance source. A highly inductive source

impedance can affect the stability of the power module.

For the test configuration in Figure 61, a 33μF

electrolytic capacitor (ESR<0.7Ω at 100kHz), mounted

close to the power module helps ensure the stability of

the unit. Consult the factory for further application

guidelines.

12μH

C_S220μF

E.S.R.<0.1Ω

33μF

@ 20°C 100kHz

Vin-

Safety Considerations

NOTE: Measure input reflected ripple current with a simulated

source inductance (L_TEST) of 12μH. Capacitor C_Soffsets

possible battery impedance. Measure current as shown

above.

For safety-agency approval of the system in which the

power module is used, the power module must be

installed in compliance with the spacing and separation

requirements of the end-use safety agency standard,

i.e., UL 60950-1-3, CSA C22.2 No. 60950-00, and VDE

0805:2001-12 (IEC60950-1).

Figure 61. Input Reflected Ripple Current Test Setup.

C O PPER STRIP

V_O(+)

V_O(–)

RESISTIV E

LO AD

If the input source is non-SELV (ELV or a hazardous

voltage greater than 60 Vdc and less than or equal to

75Vdc), for the module’s output to be considered as

meeting the requirements for safety extra-low voltage

(SELV), all of the following must be true:

1uF

.

10uF

SC O PE

GROUND PLANE

The input source is to be provided with reinforced

insulation from any other hazardous voltages, including

the ac mains.

NOTE: All voltage measurements to be taken at the module

terminals, as shown above. If sockets are used then

Kelvin connections are required at the module terminals

to avoid measurement errors due to socket contact

resistance.

One V_INpin and one V_OUTpin are to be grounded, or both

the input and output pins are to be kept floating.

Figure 62. Output Ripple and Noise Test Setup.

The input pins of the module are not operator accessible.

Another SELV reliability test is conducted on the whole

system (combination of supply source and subject

module), as required by the safety agencies, to verify that

under a single fault, hazardous voltages do not appear at

the module’s output.

R_distributionR_contact

R_contactR_distribution

Vin+

Vout+

R_LOAD

V_O

V_IN

Note: Do not ground either of the input pins of the

module without grounding one of the output pins.

This may allow a non-SELV voltage to appear

between the output pins and ground.

R_distributionR_contact

R_contactR_distribution

Vin-

Vout-

The power module has extra-low voltage (ELV) outputs

when all inputs are ELV.

NOTE: All voltage measurements to be taken at the module

terminals, as shown above. If sockets are used then

Kelvin connections are required at the module terminals

to avoid measurement errors due to socket contact

resistance.

For input voltages exceeding –60 Vdc but less than or

equal to –75 Vdc, these converters have been evaluated

to the applicable requirements of BASIC INSULATION

between secondary DC MAINS DISTRIBUTION input

(classified as TNV-2 in Europe) and unearthed SELV

outputs.

Figure 63. Output Voltage and Efficiency Test Setup.

V_O. I_O

Efficiency

=

x

100 %

η

V_IN. I_IN

"All flammable materials used in the manufacturing of

these modules are rated 94V-0 and UL60950 A.2 for

reduced thicknesses.

The input to these units is to be provided with a

maximum 3A fast-acting fuse in the unearthed lead."

LINEAGE POWER

16

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

only begin to operate once the input voltage is raised

Feature Description

above the undervoltage lockout turn-on threshold,

V_UV/ON

Remote On/Off

.

Once operating, the module will continue to operate until

the input voltage is taken below the undervoltage turn-off

Two remote on/off options are available. Positive logic

turns the module on during a logic high voltage on the

ON/OFF pin, and off during a logic low. Negative logic

remote On/Off, device code suffix “1”, turns the module

off during a logic high and on during a logic low.

threshold, V_UV/OFF

.

Over Voltage Protection

The output overvoltage protection consists of circuitry

that internally clamps the output voltage. If a more

accurate output overvoltage protection scheme is

required then this should be implemented externally via

use of the remote on/off pin.

To maintain compatibility with LW series power modules

the Remote On/Off pin is optional for the TH (through

hole) version. Standard TH modules have no On/Off pin

fitted. TH modules ordered with device code suffix “1”

are negative logic with the On/Off pin fitted.

Over Temperature Protection

To provide protection in a fault condition, the unit is

equipped with a thermal shutdown circuit. The unit will

shutdown if the overtemperature threshold of 125 ^oC is

exceeded at the thermal reference point T_ref. Once the

unit goes into thermal shutdown it will then wait to cool

before attempting to restart.

V_IN(+)

V_O

I_on/off

ON/OFF

V_on/off

Output Voltage Programming

COM

Trimming allows the output voltage set point to be

increased or decreased, this is accomplished by

connecting an external resistor between the TRIM pin

and either the V_O(+) pin or the V_O(-) pin (COM pin) .

V_IN(-)

V_IN(+)

V_O(+)

V_OTRIM

COM

Figure 64. Remote On/Off Implementation.

R_trim-up

To turn the power module on and off, the user must

supply a switch (open collector or equivalent) to control

the voltage (V_on/off) between the ON/OFF terminal and

the V_IN(-) terminal. Logic low is 0V ≤ V_on/off≤ 1.2V. The

maximum I_on/offduring a logic low is 1mA, the switch

should be maintain a logic low level whilst sinking this

current.

ON/OFF

LOAD

R_trim-down

V_IN(-)

During a logic high, the typical V_on/offgenerated by the

module is 5.8V, and the maximum allowable leakage

current at V_on/off= 5.8V is 10μA.

Figure 65. Circuit Configuration to Trim Output

Voltage.

If not using the remote on/off feature:

For positive logic, leave the ON/OFF pin open.

For negative logic, short the ON/OFF pin to V_IN(-).

Overcurrent Protection

Connecting an external resistor (R_trim-down) between the

TRIM pin and the COM pin decreases the output voltage

set point. To maintain set point accuracy, the trim

resistor tolerance should be ±0.1%.

To provide protection in a fault (output overload)

condition, the unit is equipped with internal

current-limiting circuitry and can endure current limiting

continuously. At the point of current-limit inception, the

unit enters hiccup mode. The unit operates normally

once the output current is brought back into its specified

range. The average output current during hiccup is 10%

I_{O, max}

.

Input Undervoltage Lockout

At input voltages below the input undervoltage lockout

limit, the module operation is disabled. The module will

LINEAGE POWER

17

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Feature Descriptions (continued)

The relationship between the output voltage and the trim

resistor value for a Δ% reduction in output voltage is:

R_trim-down= 249.39 kΩ

Nominal 5V, 3.3V, 2.5V, 2.0V, 1.8V, & 1.5V modules:

511

To trim up the output of a nominal 3.3V module

(HW005A0F) to 3.63V

Δ% = 10

R_trim-down

=

- 6.11 kΩ

Δ%

5.11x3.3(100+10)

1.225x10

511

Nominal 1.2V module:

R_trim-up

=

-

- 6.11 kΩ

10

346

R_trim-down

Nominal 1.0V module:

R_trim-down

=

- 4.46 kΩ

R_trim-up=94.2 kΩ

Δ%

390

=

- 4.90 kΩ

Δ%

Connecting an external resistor (R_trim-up) between the

TRIM pin and the V_O(+) pin increases the output voltage

set point. To maintain set point accuracy, the trim

resistor tolerance should be ±0.5%.

The relationship between the output voltage and the trim

resistor value for a Δ% increase in output voltage is:

Nominal 5V, 3.3V, 2.5V, 2.0V, 1.8V, & 1.5V modules:

511

5.11V_O(100+Δ%)

1.225Δ%

R_trim-up

=

-

- 6.11 kΩ

- 4.46 kΩ

Δ%

Nominal 1.2V module:

346

5.11V_O(100+Δ%)

1.225Δ%

R_trim-up

=

Δ%

Nominal 1.0V module:

390

5.11V_O(100+Δ%)

1.225Δ%

R_trim-up

=

-

- 4.90 kΩ

Δ%

(V_Orefers to the nominal output voltage, i.e. 5.0V for V_O

on an HW004A0A. Δ% is the required % change in

output voltage, i.e. to trim a 5.0V module to 5.10V the

Δ% value is 2).

Examples:

To trim down the output of a nominal 5.0V module

(HW004A0A) to 4.90V

Δ% = 2

511

R_trim-down

=

- 6.11 kΩ

2

LINEAGE POWER

18

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Thermal Considerations

C5 56nF

L2

The power modules operate in a variety of thermal

environments; however, sufficient cooling should be

provided to help ensure reliable operation.

10uH

Vin+

Vout+

C4

33uF

100V

HW005

Considerations include ambient temperature, airflow,

module power dissipation, and the need for increased

reliability. A reduction in the operating temperature of the

module will result in an increase in reliability. The

thermal data presented here is based on physical

measurements taken in a wind tunnel.

C1

0.68uF

C2

0.68uF

C3

0.68uF

Vin-

Vout-

L1 - CMC

Pulse P0354

C6 56nF

The thermal reference point, T_refused in the

specifications is shown in Figure 66. For reliable

Figure 67. Suggested Configuration for EN55022

Class B.

operation this temperature should not exceed 115 ^oC.

90

80

70

60

EN 55022 Class B Conducted Average dBuV

50

40

30

20

10

100K

Frequency(Hz)

500K

1M

5M

10M

30M

Figure 66. T_refTemperature Measurement Location.

Figure 68. EMC signature using above filter,

HW005A0F.

Please refer to the Application Note “Thermal

Characterization Process For Open-Frame Board-

Mounted Power Modules” for a detailed discussion of

thermal aspects including maximum device

temperatures.

For further information on designing for EMC

compliance, please refer to the FLTR100V10 data sheet

(FDS01-043EPS).

Layout Considerations

The HW/HC005 power module series are low profile in

order to be used in fine pitch system card architectures.

As such, component clearance between the bottom of

the power module and the mounting board is limited.

Avoid placing copper areas on the outer layer directly

underneath the power module. Also avoid placing via

interconnects underneath the power module.

Heat Transfer via Convection

Increased airflow over the module enhances the heat

transfer via convection. Derating figures showing the

maximum output current that can be delivered by each

module versus local ambient temperature (T_A) for natural

convection and up to 3m/s (600 ft./min) are shown in the

respective Characteristics Curves section.

For additional layout guide-lines, refer to FLTR100V10

data sheet.

EMC Considerations

The figure 67 shows a suggested configuration to meet

the conducted emission limits of EN55022 Class B.

LINEAGE POWER

19

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Mechanical Outline for HW/HC Surface-Mount Module

Dimensions are in millimeters and (inches).

Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]

x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)

47.2

(1.860)

Top View

29.5

(1.162)

2.54

(0.100)

8.50

(0.335)

MAX

min stand-off

Side View

height

0.5

(.020)

max

compliance

40.00

(1.576)

Bottom View

10.00

(0.394)

1

Function

Vout +

PIN 3

OPTIONAL

2

3

1

9

2

Vout -

26.16

(1.031)

Standard = No Pin

Optional = Vout +

Trim

3

9

18 17

11

17

18

On/Off

1.65

(0.065)

5.00

(0.197)

Vin -

Vin +

3.63

(0.143)

35.00

(1.379)

LINEAGE POWER

20

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Mechanical Outline for HW/HC Through Hole Module

Dimensions are in millimeters and (inches).

Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]

x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)

47.2

(1.860)

Top View

29.5

(1.162)

Side View

* Optional pin lengths shown in Table 2 Device Options

40.00

(1.576)

Bottom View

1

Function

Vout +

2

1

9

26.16

(1.031)

2

Vout -

Trim

9

11

17

18

On/Off

Vin -

18 17

11

Vin +

1.65

(0.065)

5.00

(0.197)

3.63

(0.143)

35.00

(1.379)

LINEAGE POWER

21

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Recommended Pad Layout for Surface Mount and Through Hole Module

Dimensions are in millimeters and (inches).

Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]

x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)

1

Function

Vout +

2

Vout -

Standard = No Pin

Optional = Vout +

Trim

3

9

11

17

18

On/Off

Vin -

Vin +

Surface Mount Pad Layout – Component side view

1

Function

Vout +

Vout -

2

9

Trim

11

17

18

On/Off

Vin -

Vin +

Through-Hole Pad Layout – Component side view

LINEAGE POWER

22

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Packaging Details

The surface mount versions of the HW005 family are also available in tape & reel (suffix –SR) as an option. Detailed

of tape dimensions are shown below. Modules are shipped in quantities of 115 per reel.

Tape Dimensions

Dimensions are in millimeters and (inches).

9.02

(0.355)

4.00

(0.157)

40.00

(1.575)

PICK POINT

FEED

DIRECTION

72.00

(2.834)

34.20

(1.346)

68.40

(2.692)

66.50

(2.692)

EMBOSSED CARRIER

TOP COVER TAPE

NOTE: CONFORMS TO EAI-481 REV. A STANDARD

Reel Dimensions

Outside diameter:

Inside diameter:

Tape Width:

330.2 mm (13.00”)

177.8 mm (7.00”)

72.00 mm (2.834”)

LINEAGE POWER

23

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Through-Hole Lead-Free Soldering

Information

The RoHS-compliant through-hole products use the

SAC (Sn/Ag/Cu) Pb-free solder and RoHS-compliant

components. They are designed to be processed

through single or dual wave soldering machines. The

pins have an RoHS-compliant finish that is compatible

with both Pb and Pb-free wave soldering processes.

A maximum preheat rate of 3°C/s is suggested. The

wave preheat process should be such that the

temperature of the power module board is kept below

210°C. For Pb solder, the recommended pot

temperature is 260°C, while the Pb-free solder pot is

270°C max. Not all RoHS-compliant through-hole

products can be processed with paste-through-hole

Pb or Pb-free reflow process. If additional information

is needed, please consult with your Lineage Power

representative for more details.

Figure 69. Surface Mount Packaging Tray

Tray Specification

Material

Antistatic coated PVC

10¹²Ω/sq

Max surface resistivity

Color

Clear

Surface Mount Information

Packaging Details

Capacity

15 power modules

Min order quantity

60 pcs (1 box of 4 full

trays)

The surface mount versions of the HW005 family

(suffix –S) are supplied as standard in the plastic tray

shown in Figure 69. The tray has external

dimensions of 135.1mm (W) x 321.8mm (L) x 12.4mm

(H) or 5.319in (W) x 12.669in (L) x 0.489in (H).

Each tray contains a total of 15 power modules. The

trays are self-stacking and each shipping box will

contain 4 full trays plus one empty hold down tray

giving a total number of 60 power modules.

Surface mount versions of the HW005 family are also

available as an option packaged in Tape and Reel.

For further information on this please contact your

local Lineage Power Technical Sales Representative.

Pick and Place

The HW005-S series of DC-to-DC power converters

use an open-frame construction and are designed for

surface mount assembly within a fully automated

manufacturing process.

The HW005-S series modules are fitted with a Kapton

label designed to provide a large flat surface for pick

and placing. The label is located covering the Centre

of Gravity of the power module. The label meets all

the requirements for surface-mount processing, as

well as meeting UL safety agency standards. The

label will withstand reflow temperatures up to 300°C.

The label also carries product information such as

product code, date and location of manufacture.

LINEAGE POWER

24

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

damage to the modules, and can adversely affect

long-term reliability.

Surface Mount Information (continued)

The surface mountable modules in the HW005 family

use our newest SMT technology called “Column Pin”

(CP) connectors. Fig 71 shows the new CP connector

before and after reflow soldering onto the end-board

assembly.

24.2

COG

HW005 Board

Insulator

19.0

9.5

Solder Ball

End assembly PCB

Note: All dimensions in mm.

Figure 70. Pick and Place Location.

Figure 71. Column Pin Connector Before and After

Reflow Soldering.

Z Plane Height

The CP is constructed from a solid copper pin with an

integral solder ball attached, which is composed of

tin/lead (Sn/Pb) solder. The CP connector design is

able to compensate for large amounts of co-planarity

and still ensure a reliable SMT solder joint.

The ‘Z’ plane height of the pick and place location is

7.50mm nominal with an RSS tolerance of +/-0.25

mm.

Nozzle Recommendations

Typically, the eutectic solder melts at 183^oC, wets the

land, and subsequently wicks the device connection.

Sufficient time must be allowed to fuse the plating on

the connection to ensure a reliable solder joint. There

are several types of SMT reflow technologies

currently used in the industry. These surface mount

power modules can be reliably soldered using natural

forced convection, IR (radiant infrared), or a

combination of convection/IR. For reliable soldering

the solder reflow profile should be established by

accurately measuring the modules CP connector

temperatures.

The module weight has been kept to a minimum by

using open frame construction. Even so, they have a

relatively large mass when compared with

conventional SMT components. Variables such as

nozzle size, tip style, vacuum pressure and placement

speed should be considered to optimize this process.

The minimum recommended nozzle diameter for

reliable operation is 6mm. The maximum nozzle outer

diameter, which will safely fit within the allowable

component spacing, is 9 mm.

Oblong or oval nozzles up to 11 x 9 mm may also be

used within the space available.

300

Peak Temp 235^oC

For further information please contact your local

Lineage Power Technical Sales Representative.

250

Cooling

zone

1- 4 ^oCs^-1

Heat zone

max 4^oCs^-1

200

150

10 0

50

Reflow Soldering Information

The HW005 family of power modules is available for

either Through-Hole (TH) or Surface Mount (SMT)

soldering. These power modules are large mass, low

thermal resistance devices and typically heat up

slower than other SMT components. It is

recommended that the customer review data sheets

in order to customize the solder reflow profile for each

application board assembly.

Soak zone

30-240s

T

_limabove

205^oC

Preheat zone

max 4^oCs^-1

0

REFLOW TIME (S)

The following instructions must be observed when

SMT soldering these units. Failure to observe these

instructions may result in the failure of or cause

Figure 72. Recommended Reflow Profile

LINEAGE POWER

25

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

The shelf life for dry packed SMT packages will be a

Surface Mount Information (continued)

minimum of 12 months from the bag seal date, when

stored at the following conditions: < 40° C, < 90%

relative humidity.

240

235

230

225

220

215

210

205

200

Post Solder Cleaning and Drying

Considerations

Post solder cleaning is usually the final circuit-board

assembly process prior to electrical board testing. The

result of inadequate cleaning and drying can affect

both the reliability of a power module and the

testability of the finished circuit-board assembly. For

guidance on appropriate soldering, cleaning and

drying procedures, refer to Lineage Power Board

Mounted Power Modules: Soldering and Cleaning

Application Note (AP01-056EPS).

0

10

20

30

40

50

60

TIME LIMIT (S)

300

Figure 73. Time Limit Curve Above 205^oC Reflow .

Per J-STD-020 Rev. C

Peak Temp 260°C

250

Cooling

Lead Free Soldering

200

Zone

* Min. Time Above 235°C

The –Z version SMT modules of the HW/HC series

are lead-free (Pb-free) and RoHS compliant and are

compatible in a Pb-free soldering process. Failure to

observe the instructions below may result in the

failure of or cause damage to the modules and can

adversely affect long-term reliability.

15 Seconds

150

Heating Zone

1°C/Second

*Time Above 217°C

60 Seconds

100

50

0

Reflow Time (Seconds)

Pb-free Reflow Profile

Power Systems will comply with J-STD-020 Rev. C

(Moisture/Reflow Sensitivity Classification for

Nonhermetic Solid State Surface Mount Devices) for

both Pb-free solder profiles and MSL classification

procedures. This standard provides a recommended

forced-air-convection reflow profile based on the

volume and thickness of the package (table 4-2). The

suggested Pb-free solder paste is Sn/Ag/Cu (SAC).

The recommended linear reflow profile using

Sn/Ag/Cu solder is shown in Figure. 74.

Figure 74. Recommended linear reflow profile

using Sn/Ag/Cu solder.

Solder Ball and Cleanliness Requirements

The open frame (no case or potting) power module

will meet the solder ball requirements per

J-STD-001B. These requirements state that solder

balls must neither be loose nor violate the power

module minimum electrical spacing.

The cleanliness designator of the open frame power

module is C00 (per J specification).

MSL Rating

The HW/HC series SMT modules have a MSL rating

of 1.

Storage and Handling

The recommended storage environment and handling

procedures for moisture-sensitive surface mount

packages is detailed in J-STD-033 Rev. A (Handling,

Packing, Shipping and Use of Moisture/Reflow

Sensitive Surface Mount Devices). Moisture barrier

bags (MBB) with desiccant are required for MSL

ratings of 2 or greater. These sealed packages

should not be broken until time of use. Once the

original package is broken, the floor life of the product

at conditions of ≤ 30°C and 60% relative humidity

varies according to the MSL rating (see J-STD-033A).

LINEAGE POWER

26

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Ordering Information

Please contact your Lineage Power Sales Representative for pricing, availability and optional features.

Table 1. Device Codes

Remote

On/Off

Logic

Input

Voltage

Output

Voltage

Output

Current

Connector

Type

Product codes

Comcodes

HW004A0A-S

HW004A0A-SZ

HW004A0A1

HW004A0A1-S

HW004A0A1Z

HW004A0A1-SB

HW004A0A1-SZ

HW005A0F-S

48 Vdc

24 Vdc

5.0V

3.3V

2.5V

2.0V

1.8V

1.2V

5.0V

3.3V

4A

5A

6A

4A

5A

Positive

SMT

Through-Hole

SMT

Through-Hole

SMT

108968272

109100245

108965476

108960634

CC109102002

108980525

109100237

108968678

109100261

108986951

108967779

CC109107125

108960667

108995197

109100253

108987512

108995206

109100311

108969676

109100303

108960782

109100344

109100336

108960642

108996113

108960659

108996121

Positive

Negative

Positive

SMT

HW005A0F-SZ

HW005A0F-SR39*

HW005A0F1

Positive

SMT (tape & reel)

Through-Hole

SMT

SMT (tape&reel)

SMT

Negative

HW005A0F1Z

HW005A0F1-S

HW005A0F1-SZ

HW005A0F1-SRZ

HW005A0F1-S65*

HW005A0F1-S65Z*

HW006A0G1-SZ

HW006A0D1-S

HW006A0D1-SZ

HW006A0Y1-S

HW006A0Y1-SZ

HW006A0P1-SZ

HC004A0A1-S

HC004A0A1-SZ

HC005A0F1-S

HC005A0F1-SZ

SMT

LINEAGE POWER

27

Data Sheet

HW/HC004/005/006 Series DC-DC Power Module:

May 16, 2008

18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current

Table 2. Device Options

Option

Suffix

1

Negative remote on/off logic

With additional Vout+ pin3

Short Pins: 3.68 mm ± 0.25 mm (0.145 in ±0.010 in)

Short Pins: 2.79 mm ± 0.25 mm (0.110 in ±0.010 in)

Customer specific

3

6

8

-39

-65

-R

-S

-Z

Customer specific

Tape & Reel

Surface mount connections

RoHS Compliant

* Please contact Lineage Power for availability of these options, samples, minimum order quantity and lead times

Asia-Pacific Headquarters

Tel: +65 6416 4283

Europe, Middle-East and Africa Headquarters

World Wide Headquarters

Tel: +49 89 6089 286

Lineage Power Corporation

3000 Skyline Drive, Mesquite, TX 75149, USA

+1-800-526-7819

India Headquarters

(Outside U.S.A.: +1-972-284-2626)

www.lineagepower.com

Tel: +91 80 28411633

e-mail: techsupport1@lineagepower.com

^{Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is}D^aso^suc^mu^em^de^an^st^aN^reo^su:^ltD^oS^{f th}0^e3^ir-0^us1^e7^orver.1.21

application. No rights under any patent accompany the sale of any such product(s) or information.

PDF No: hw-hc_4-6a.pdf

型号	制造商	描述	价格	文档
HW005A0F1Z	LINEAGEPOWER	18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current	获取价格
HW006A0D1-S	LINEAGEPOWER	18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current	获取价格
HW006A0D1-SZ	LINEAGEPOWER	18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current	获取价格
HW006A0G1-SZ	LINEAGEPOWER	18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current	获取价格
HW006A0P1-SZ	LINEAGEPOWER	18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current	获取价格
HW006A0Y1-S	LINEAGEPOWER	18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current	获取价格
HW006A0Y1-SZ	LINEAGEPOWER	18-36Vdc & 36-75Vdc Input; 1.0V-5Vdc Output; 4A - 6A Output Current	获取价格
HW006A6A-S	LINEAGEPOWER	36-75 Vdc Input; 1.2 Vdc to 5 Vdc Output; 6.6A to 12A	获取价格
HW006A6A1	LINEAGEPOWER	36-75 Vdc Input; 1.2 Vdc to 5 Vdc Output; 6.6A to 12A	获取价格
HW006A6A1-S	LINEAGEPOWER	36-75 Vdc Input; 1.2 Vdc to 5 Vdc Output; 6.6A to 12A	获取价格

HW005A0F1-SZ

HW005A0F1-SZ 概述

HW005A0F1-SZ 数据手册

HW005A0F1-SZ 相关器件

HW005A0F1-SZ 相关文章

热门型号