LTL-4233-051A [LITEON]
Property of Lite-On Only; 精简版，关于财产只有
| 型号： | LTL-4233-051A |
| 厂家： | 
LITE-ON TECHNOLOGY CORPORATION |
| 描述： | Property of Lite-On Only |
| 文件： | 总7页 (文件大小：262K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Features
* High Intensity.
* Popular T-1
diameter Package.
3/4
* Selected minimun intensities.
* General purpose leads.
* Reliable and rugged.
Package Dimensions
Part No.
Lens
Source Color
Green
LTL-4233-051A
Green Diffused
Notes:
1. All dimensions are in millimeters (inches).
±
2. Tolerance is 0.25mm(.010") unless otherwise noted.
3. Protruded resin under flange is 1.0mm(.04") max.
4. Lead spacing is measured where the leads emerge from the package.
5. Specifications are subject to change without notice.
Part No. : LTL-4233-051A
BNS-OD-C131/A4
Page :
1
of
7
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
℃
Absolute Maximum Ratings at TA=25
Parameter
Maximum Rating
100
Unit
mW
Power Dissipation
Peak Forward Current
120
mA
mA
(1/10 Duty Cycle, 0.1ms Pulse Width)
Continuous Forward Current
30
0.4
5
℃
℃
mA/
Derating Linear From 50
Reverse Voltage
V
℃
℃
℃
-55 to + 100
Operating Temperature Range
Storage Temperature Range
℃
-55 to + 100
Lead Soldering Temperature
[1.6mm(.063") From Body]
℃
260 for 5 Seconds
Part No. : LTL-4233-051A
BNS-OD-C131/A4
Page :
1
of
7
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
℃
Electrical / Optical Characteristics at TA=25
Parameter
Luminous Intensity
Viewing Angle
Symbol
IV
Min.
5.6
Typ.
Max.
Unit
mcd
deg
nm
nm
nm
V
Test Condition
IF = 10mA
Note 1,4
19
36
θ
2
1/2
Note 2 (Fig.6)
Measurement
@Peak (Fig.1)
λP
λd
Peak Emission Wavelength
Dominant Wavelength
Spectral Line Half-Width
Forward Voltage
565
569
30
Note 3
Δλ
VF
IR
2.1
2.6
IF = 20mA
μ
A
Reverse Current
100
VR = 5V
Capacitance
C
35
pF
VF = 0 , f = 1MHz
Note: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE
(Commission International De L'Eclairage) eye-response curve.
θ
2. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
λd is derived from the CIE chromaticity diagram and represents the single
3. The dominant wavelength,
wavelength which defines the color of the device.
±
4. The Iv guarantee should be added 15%.
Part No. : LTL-4233-051A
BNS-OD-C131/A4
Page :
3
of
7
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Typical Electrical / Optical Characteristics Curves
℃
(25 Ambient Temperature Unless Otherwise Noted)
Part No. : LTL-4233-051A
BNS-OD-C131/A4
Page :
4
of
7
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Features
* Compatible with radial lead automatic insertion equipment.
* Most radial lead plastic lead lamps available packaged in tape and folding.
* 5mm (0.197") formed lead and 2.54mm (0.1") straight lead spacing available.
* Folding packaging simplifies handling and testing.
Package Dimensions
Specification
Minimum Maximum
Item
Symbol
mm
3.8
inch
0.149
0.188
--
mm
4.2
inch
0.165
0.228
0.078
0.649
0.898
0.60
Tape Feed Hole Diameter
Component Lead Pitch
Front to Rear Deflection
Height of Seating Plane
D
F
4.8
5.8
△
H
--
2.0
H
15.5
20.8
13.7
0.610
0.818
0.540
16.5
22.8
15.2
11.0
13.0
4.55
7.65
0.90
9.75
15.5
3.0
Feed Hole to Bottom of Component
Seating Plane to Top of Component
Lead Length After Component Height
Feed Hole Pitch
H1
H3
L
W0
0.433
0.511
0.179
0.301
0.035
0.384
0.610
0.118
0.748
P
12.4
3.15
5.05
--
0.488
0.124
0.198
--
Lead Location
P1
P2
T
Center of Component Location
Total Tape Thickness
Feed Hole Location
W0
W1
W2
W3
8.5
0.334
0.571
0
Adhesive Tape Width
14.5
0
Adhesive Tape Position
Tape Width
17.5
0.689
19.0
Part No. : LTL-4233-051A
BNS-OD-C131/A4
Page :
5
of
7
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
CAUTIONS
1. Application limitation
The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment,
communication equipment and household application.) Consult Liteon’s sales in advance for information on
application in which exceptional quality and reliability are required, particularly when the failure or malfunction
of the LEDs may directly jeopardize life or health (such as airplanes, automobiles, traffic control equipment, life
support system and safety devices).
2. Storage
After being shipped from Liteon the LEDs should be kept at 30°C or less and 70%RH or less.
The LEDs should be used within 3 months. They can be stored for a year in a sealed container with a nitrogen
atmosphere and moisture absorbent material. Please avoid rapid transitions in ambient temperature in high
humidity environments where condensation may occur.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED.
4. Forming & Mounting
When forming a lead, the leads should be bent at a point at least 3mm from the base of epoxy bulb. Do not use
the base of the leadframe as a fulcrum during forming. Lead forming must be done before soldering at normal
temperature. When mounted through hole type LED lamp, avoid the occurrence of residual mechanical stress
due to clinching.
5. Soldering
When soldering, leave a minimum of 2mm clearance from the resin to the soldering point.
Dipping the resin into the solder must be avoided.
Do not apply any stress to the lead frame during soldering while the LED is at high temperature.
Recommended soldering condition
Soldering iron
300°C Max.
Wave soldering
100°C Max.
Temperature
Pre-heat
Soldering time
3 sec. Max.
Pre-heat time
Solder wave
Soldering time
60 sec. Max.
260°C Max.
10 sec. Max.
(one time only)
6. Drive Method
LED is a current operated device, and therefore, requires some kind of current limiting incorporated into the
drive circuit. This current limiting typically takes the form of a current limiter resistor placed in series with
the LED. Consider worst case voltage variations that could occur across the current limiting resistor.
The forward current should not be allowed to change by more than 40% of its desired value.
Circuit model A
Circuit model B
LED
LED
(A) Recommended circuit.
(B) The difference of brightness between LEDs could be found due to the Vf-If characteristics of LED
Part No. : LTL-4233-051A
BNS-OD-C131/A4
Page :
6
of
7
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
7. ESD (Electrostatic Discharge)
Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti- electrostatic glove
is recommended when handling these LED. All devices, equipment and machinery must be properly grounded.
8. Reliability Test
Duration
/ Cycle
Classification
Test Item
Test Condition
Referance Standard
Ta= Room Temp,
MIL-STD-750D:1026 (1995)
MIL-STD-883D:1005 (1991)
JIS C 7021:B-1 (1982)
Endurance
Test
Room Temp.
1000 hrs
Ip= 160 mA / 1/8 duty,
Pulse Width =1.25 ms
Operation Life
MIL-STD-202F:107D (1980)
MIL-STD-750D:1051(1995)
MIL-STD-883D:1010 (1991)
JIS C 7021: A-4(1982)
105℃ ～ 25℃ ～ -55℃ ～ 25℃
Temperature
Cycling
10 cycles
10 sec
30mins 5mins
30mins 5mins
MIL-STD-202F:210A(1980)
MIL-STD-750D:2031(1995)
JIS C 7021: A-1(1982)
Solder
Environmental
Test
Solder temperature is 260± 5 ℃
Solder temperature is 230± 5 ℃
Resistance
MIL-STD-202F:208D(1980)
MIL-STD-750D:2026(1995)
MIL-STD-883D:2003(1991)
JIS C 7021: A-2(1982)
5 sec
Solderability
9. Others
The appearance and specifications of the product may be modified for improvement without notice.
Part No. : LTL-4233-051A
BNS-OD-C131/A4
Page :
7
of
7
相关型号：
©2020 ICPDF网 联系我们和版权申明