LTW-008RGB-L [LITEON]
Property of Lite-On Only; 精简版，关于财产只有
| 型号： | LTW-008RGB-L |
| 厂家： | 
LITE-ON TECHNOLOGY CORPORATION |
| 描述： | Property of Lite-On Only |
| 文件： | 总11页 (文件大小：453K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Features
* Package in 12mm tape on 7" diameter reels.
* Compatible with automatic placement equipment.
* Compatible with infrared and vapor phase reflow solder process.
* EIA STD package.
* I.C. compatible.
* Meet green product and Pb-free(According to RoHS)
Package Dimensions
Part No.
Lens Color
Water clear
Source Color
InGaN Blue
InGaN Green
AlInGaP Red
LTW-008RGB-L
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1 mm (.004") unless otherwise noted.
Part No. : LTW-008RGB-L
BNS-OD-C131/A4
Page :
1
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
°C
Absolute Maximum Ratings at Ta=25
Rating
Parameter
Power Dissipation
Symbol
Unit
R
75
G
120
B
Po
IFP
120
100
30
mW
mA
mA
V
Peak Forward Current 1
Continuous Forward Current
Reverse Voltage
100
30
100
IF
30
VR
Topr
Tstg
Tsol
5
Operating Temperature Range
Storage Temperature Range
Soldering Condition
-40 ~ +85
-40 ~ +100
°C
°C
260°C For 10 Seconds
Note 1: 1/10 Duty Cycle, 0.1ms Pulse Width.
Suggestion IR Reflow Profile For Pb Free Process
:
IR-Reflow Soldering Profile for lead free soldering (Acc. to J-STD-020B)
Part No. : LTW-008RGB-L
BNS-OD-C131/A4
Page :
2
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
°C
Absolute Maximum Ratings at Ta=25
Values
Parameter
Symbol
Test Condition
Unit
R
G
B
Min
500
700
610
620
623
1.8
700
100
R: IF = 20mA
G: IF = 20mA
B: IF = 20mA
Luminous Intensity 1
Viewing Angle
IV
mcd
°
Typ.
Max.
Typ.
Min
1200
120
300
455
465
455
3.0
2θ1/2
IF = 20mA
520
R: IF = 20mA
G: IF = 20mA
B: IF = 20mA
Dominant Wavelength 2
nm
Typ.
Max.
Min
λd
530
518
3.0
R: IF = 20mA
G: IF = 20mA
B: IF = 20mA
Peak Wavelength
Forward Voltage 3
nm
V
Typ.
Max.
Min
λp
R: IF = 20mA
G: IF = 20mA
B: IF = 20mA
VF
Typ.
Max.
Typ.
Max.
2.4
3.6
2.66
10
3.6
Luminous Flux
Reverse Current
1.57
0.49
IF = 20mA
VR = 5V
lm
ꢀA
nm
Φv
IR
Spectrum Radiation
Bandwidth
Typ.
20
33
22
IF = 20mA
∆
λ
Note :
1. Tolerance of Luminous Intensity +/- 10%
2. Tolerance of Dominant Wavelength +/- 1nm
3. Tolerance of Forward Voltage +/- 0.1V
4. Caution in ESD:
Static Electricity and surge damages the LED. It is recommend to use a wrist band or
anti-electrostatic glove when handling the LED. All devices, equipment and machinery
must be properly grounded.
5. CAS140B is the test standard for the chromaticity coordinates IV.
.
Part No. : LTW-008RGB-L
BNS-OD-C131/A4
Page :
3
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Bin Code List
VF Spec. Table
Forward Voltage (V) at IF: R=20mA, G=20mA, B=20mA
Rank
Red
1.8 – 2.1
2.1 – 2.4
Green
Blue
3.0 – 3.3
3.3 – 3.6
V11
V12
V21
V22
W11
W12
W21
W22
Tolerance on each Forward Voltage bin is +/- 0.10volt.
IV Spec. Table
Luminous Intensity (mcd) at IF: R=20mA, G=20mA, B=20mA
Rank
Red
500 – 700
Green
Blue
100 – 200
200 – 300
A21
A22
A31
A32
A41
A42
A51
A52
A61
A62
Tolerance on each Luminous Intensity bin is +/- 10%.
Part No. : LTW-008RGB-L
BNS-OD-C131/A4
Page :
4
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Bin Code List
λ
D Spec. Table
Dominated Wavelength (nm) at IF: R=20mA, G=20mA, B=20mA
Rank
Red
610 – 620
Green
520 – 525
525 – 530
Blue
455 – 460
460 – 465
M
P
N
R
Tolerance on each Dominated Wavelength bin is +/- 1nm.
Part No. : LTW-008RGB-L
BNS-OD-C131/A4
Page :
5
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
100%
80%
60%
40%
20%
0%
Blue
Green
Red
nm
350
400
450
500
550
600
650
700
Wavelength
Fig.1 Relative Intensity vs Dominant Wavelength
Part No. : LTW-008RGB-L
BNS-OD-C131/A4
Page :
6
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
User Guide
Cleaning
Do not use unspecified chemical liquid to clean LED they could harm the package.
If cleaning is necessary, immerse the LED in ethyl alcohol or isopropyl alcohol at
normal temperature for less one minute.
Recommend Printed Circuit Board Attachment Pad
Infrared / vapor phase
Reflow Soldering
Package Dimensions of Tape
Part No. : LTW-008RGB-L
BNS-OD-C131/A4
Page :
7
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
Package Dimensions of Reel
Notes:
1. Empty component pockets sealed with top cover tape.
2. 7 inch reel-2000 pieces per reel.
3. Minimum packing quantity is 500 pieces for remainders.
4. The maximum number of consecutive missing lamps is two.
5. In accordance with EIA-481-1-B specifications.
Part No. : LTW-008RGB-L
BNS-OD-C131/A4
Page :
8
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office
equipment, communication equipment and household applications).Consult Liteon’s Sales in advance for
information on applications in which exceptional reliability is required, particularly when the failure or
malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic
control equipment, medical and life support systems and safety devices).
2. Storage
This product is qualified as Moisture sensitive Level 3 per JEDEC J-STD-020 Precaution when handing
this moisture sensitive product is important to ensure the reliability of the product.
The package is sealed:
The LEDs should be stored at 30°C or less and 90%RH or less. And the LEDs are limited to use
within one year, while the LEDs is packed in moisture-proof package with the desiccants inside.
The package is opened:
The LEDs should be stored at 30°C or less and 60%RH or less. Moreover, the LEDs are limited to
solder process within 168hrs. If the Humidity Indicator shows the pink color in 10% even higher or
exceed the storage limiting time since opened, that we recommended to baking LEDs at 60°C at least
48hrs. To seal the remainder LEDs return to package, it’s recommended to be with workable
desiccants in original package.
3. Cleaning
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary.
4. Soldering
Recommended soldering conditions:
Reflow soldering
Soldering iron
Pre-heat
Pre-heat time
120~150°C
120 sec. Max.
Temperature
Soldering time
300°C Max.
3 sec. Max.
Soldering
Soldering time
Temp. 260°C Max.
30 sec. Max.
(one time only)
5. Drive Method
An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected
in parallel in an application, it is recommended that a current limiting resistor be incorporated in the
drive circuit, in series with each LED as shown in Circuit A below.
Circuit model A
Circuit model B
LED
LED
(A) Recommended circuit.
(B) The brightness of each LED might appear different due to the differences in the I-V characteristics
of those LEDs.
Part No. : LTW-008RGB-L
BNS-OD-C131/A4
Page :
9
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
6. ESD (Electrostatic Discharge)
Static Electricity or power surge will damage the LED.
Suggestions to prevent ESD damage:
ꢀ Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs.
ꢀ
ꢀ
ꢀ
All devices, equipment, and machinery must be properly grounded.
Work tables, storage racks, etc. should be properly grounded.
Use ion blower to neutralize the static charge which might have built up on surface of the LED’s
plastic lens as a result of friction between LEDs during storage and handling.
ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward
Voltage, or “no light-up” at low currents.
To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents.
The Vf of “good” LEDs should be>2.0V@0.1mA for InGaN product.
7.1 Reliability Test
Number of
Damaged
Test Item
Test Condition
Reference Standard
Note
± ℃
Solderability
(Reflow Soldering)
Tsld=245 5 , 3sec.
1 time
Over 95%
JEITA ED-4701
300 303
0/50
0/50
0/50
(Lead Free Solder)
℃
℃
~ 85
30min. 30min.
-30
JEITA ED-4701
300 307
Thermal Shock
100 cycles
100 cycles
℃
℃
℃
℃
~ 25
-40
~ 25
~ 100
JEITA ED-4701
100 105
Temperature Cycle
30min. 5min. 30min. 5min.
25℃ ~ 65℃ ~ -10℃
90%RH 24HRS./1cycle
JEITA ED-4701
200 203
Moisture Resistance Cyclic
High Temperature Storage
10 cycles
1000 hrs.
1000 hrs.
1000 hrs.
1000 hrs.
0/50
0/50
0/50
0/50
0/50
JEITA ED-4701
200 201
Ta=100℃
Temperature Humidity
Storage
JEITA ED-4701
100 103
Ta=60℃, RH=90%
Ta=-40℃
JEITA ED-4701
200 202
Low Temperature Storage
Steady State
Operating Life Condition 1
Ta=25℃, IF=20mA
Steady State
Operating Life Condition 2
Ta=25℃, IF=30mA
Ta=85℃, IF=5mA
500 hrs.
0/50
0/50
Steady State
Operating Life of High
Temperature
1000 hrs.
Steady State
60℃, RH=90% , IF=15mA
Ta=-30℃, IF=20mA
Operating Life of High
Humidity Heat
500 hrs.
0/50
0/50
Steady State
Operating Life of low
Temperature
1000 hrs.
Part No. : LTW-008RGB-L
BNS-OD-C131/A4
Page :
10
of
11
LITE-ON TECHNOLOGY CORPORATION
P r o p e r t y o f L i t e - O n O n l y
7.2 Criteria for Judging the Damage
Criteria for Judgment
Item
Symbol Test Conditions
Min.
-
Max.
U.S.L.*) × 1.1
Forward Voltage
Reverse Current
VF
IR
IF=20mA
VR=5V
-
-
-
U.S.L.*) × 2.0
-
U.S.L.**) × 0.7
Luminous Intensity
IV
IF=20mA
-
8. Others
The appearance and specifications of the product may be modified for improvement without prior notice.
9. Suggested Checking List
Training and Certification
1. Everyone working in a static-safe area is ESD-certified?
2. Training records kept and re-certification dates monitored?
Static-Safe Workstation & Work Areas
1. Static-safe workstation or work-areas have ESD signs?
2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V?
3. All ionizer activated, positioned towards the units?
4. Each work surface mats grounding is good?
Personnel Grounding
1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or
conductive shoes with conductive flooring?
2. If conductive footwear used, conductive flooring also present where operator stand or walk?
3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*?
4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs?
5. All wrist strap or heel strap checkers calibration up to date?
Note: *50V for Blue LED.
Device Handling
1. Every ESDS items identified by EIA-471 labels on item or packaging?
2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe
workstation?
3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items?
4. All flexible conductive and dissipative package materials inspected before reuse or recycle?
Others
1. Audit result reported to entity ESD control coordinator?
2. Corrective action from previous audits completed?
3. Are audit records complete and on file?
Part No. : LTW-008RGB-L
BNS-OD-C131/A4
Page :
11
of
11
相关型号：
©2020 ICPDF网 联系我们和版权申明