30KPA28CAB [LITTELFUSE]
30000W, BIDIRECTIONAL, SILICON, TVS DIODE, HALOGEN FREE AND ROHS COMPLIANT, PLASTIC PACKAGE-2;
| 型号： | 30KPA28CAB |
| 厂家： | 
LITTELFUSE |
| 描述： | 30000W, BIDIRECTIONAL, SILICON, TVS DIODE, HALOGEN FREE AND ROHS COMPLIANT, PLASTIC PACKAGE-2 二极管 电视 瞬态抑制器 |
| 文件： | 总6页 (文件大小：915K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TransientVoltage Suppression Diodes
Axial Leaded – 30000W > 30KPA series
RoHS
30KPA Series
Description
Uni-directional
The 30KPA Series is designed specifically to protect
sensitive electronic equipment from voltage transients
induced by lightning and other transient voltage events.
Features
Bi-directional
• VBR @TJ= VBR@25°C × (1+αT • ESD protection of data
lines in accordance with
IEC 61000-4-2 (IEC801-2)
x (TJ - 25))
(αT:Temperature Coefficient)
• EFT protection of data
lines in accordance with
IEC 61000-4-4 (IEC801-4)
• Low incremental surge
resistance
• Glass passivated chip
junction in P600 package
• 30000W peak pulse
capability at 10/1000μs
waveform, repetition rate
(duty cycles):0.01%
• Fast response time:
typically less than 1.0ps
from 0 Volts to BV min
Agency Approvals
AGENCY
AGENCY FILE NUMBER
E230531
• Typical IR less than 2μA
above 73V
• High temperature
soldering guaranteed:
260°C/40 seconds /
0.375”,(9.5mm) lead
length, 5 lbs., (2.3kg)
tension
• Plastic package has
underwriters laboratory
flammability classification
94V-O
Maximum Ratings andThermal Characteristics
(TA=25°C unless otherwise noted)
• Excellent clamping
capability
•Typical failure mode is
short from over-specified
voltage or current
• Whisker test is conducted
based on JEDEC
JESD201A per its table 4a
and 4c
• IEC-61000-4-2 ESD
Parameter
Symbol
PPPM
Value
Unit
W
Peak Pulse Power Dissipation by
10/1000μsTest Waveform (Fig.1)
(Note 1)
30000
Steady State Power Dissipation on
Inifinite Heat Sink atTL=75ºC (Fig. 5)
PD
8.0
W
A
• Matte tin lead–free plated
• Halogen free and RoHS
compliant
Peak Forward Surge Current, 8.3ms
Single Half Sine Wave Unidirectional
Only (Note 2)
IFSM
400
15kV(Air), 8kV (Contact)
Operating Junction and Storage
Temperature Range
TJ, TSTG -55 to 150
°C
TypicalThermal Resistance Junction
to Lead
Applications
RuJL
RuJA
8.0
40
°C/W
°C/W
TVS devices are ideal for the protection of I/O interfaces,
CC bus and other vulnerable circuits used in telecom,
TypicalThermal Resistance Junction
to Ambient
V
computer, industrial and consumer electronic applications.
Notes:
1. Non-repetitive current pulse , per Fig. 4 and derated aboveTA = 25°C per Fig. 3.
2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per
minute maximum.
Additional Information
Functional Diagram
Datasheet
Resources
Samples
Bi-directional
Cathode
Anode
Uni-directional
© 2014 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/24/14
TransientVoltage Suppression Diodes
Axial Leaded – 30000W > 30KPA series
Electrical Characteristics (TA=25°C unless otherwise noted)
Maximum
Reverse
Leakage
IR @VR
Maximum
Clamping
Voltage
VC @ IPP
(V)
Breakdown
Reverse
Test
Current
IT
Maximum
Peak
Pulse Current
Ipp (A)
Agency
Part
Number
(Uni)
Part
Number
(Bi)
Voltage VBR
(Volts) @ IT
Stand off
Voltage VR
(Volts)
Approval
(mA)
MIN
MAX
34.41
36.86
40.59
44.22
47.96
51.59
52.80
55.33
58.96
62.70
66.33
71.28
73.70
78.65
81.07
86.02
87.23
88.44
92.18
(µ A)
5000
5000
5000
5000
2000
1000
1000
250
150
50
20
20
15
10
2
2
2
2
30KPA28CA
30KPA30CA
30KPA33CA
30KPA36CA
30KPA39CA
30KPA42CA
30KPA43CA
30KPA45CA
30KPA48CA
30KPA51CA
30KPA54CA
30KPA58CA
30KPA60CA
30KPA64CA
30KPA66CA
30KPA70CA
30KPA71CA
30KPA72CA
30KPA75CA
28
30
33
36
39
42
43
45
48
51
54
58
60
64
66
70
71
72
75
31.28
33.51
36.90
40.20
43.60
46.90
48.00
50.30
53.60
57.00
60.30
64.80
67.00
71.50
73.70
78.20
79.30
80.40
83.80
50
50
50
50
20
10
10
5
5
5
5
5
5
5
5
5
5
5
5
606.0
548.9
517.9
490.3
450.9
420.8
415.1
391.5
371.3
350.7
331.5
327.9
297.1
291.3
283.2
278.0
271.7
265.8
253.8
50.0
55.2
58.5
61.8
30KPA28A
30KPA30A
30KPA33A
30KPA36A
30KPA39A
30KPA42A
30KPA43A
30KPA45A
30KPA48A
30KPA51A
30KPA54A
30KPA58A
30KPA60A
30KPA64A
30KPA66A
30KPA70A
30KPA71A
30KPA72A
30KPA75A
30KPA78A
30KPA84A
30KPA90A
30KPA96A
30KPA102A
30KPA108A
30KPA120A
30KPA132A
30KPA144A
30KPA150A
30KPA156A
30KPA160A
30KPA168A
30KPA170A
30KPA180A
30KPA198A
30KPA216A
30KPA240A
30KPA258A
30KPA260A
30KPA270A
30KPA280A
30KPA288A
30KPA300A
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
67.2
72.0
73.0
77.4
81.6
86.4
91.4
92.4
102.0
104.0
107.0
109.0
111.5
114.0
119.4
2
30KPA78CA
30KPA84CA
30KPA90CA
30KPA96CA
30KPA102CA
30KPA108CA
30KPA120CA
30KPA132CA
30KPA144CA
30KPA150CA
30KPA156CA
30KPA160CA
30KPA168CA
30KPA170CA
30KPA180CA
78
84
90
87.10
93.80
95.81
103.18
110.55
117.92
125.29
132.66
147.40
162.14
176.88
184.36
191.73
196.57
206.47
208.89
221.21
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
234.9
217.7
207.0
194.2
183.0
172.9
155.9
142.3
135.8
129.8
123.7
120.0
111.2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
129.0
139.2
146.4
156.0
165.6
175.2
194.4
213.0
223.2
233.4
245.0
252.6
272.4
275.0
290.4
100.50
107.20
113.90
120.60
134.00
147.40
160.80
167.60
174.30
178.70
187.70
189.90
201.10
96
102
108
120
132
144
150
156
160
168
170
180
110.2
104.3
30KPA198CA
30KPA216CA
30KPA240CA
30KPA258CA
30KPA260CA
30KPA270CA
30KPA280CA
30KPA288CA
30KPA300CA
198
216
240
258
260
270
280
288
300
221.20
241.30
268.10
288.20
290.40
301.60
312.80
321.70
334.00
243.32
265.43
294.91
317.02
319.44
331.76
344.08
353.87
367.40
5
5
5
5
5
5
5
5
5
94.7
86.9
78.3
72.8
72.8
69.5
65.3
64.5
62.0
2
2
2
2
2
2
2
2
2
319.8
348.6
387.0
416.4
416.0
436.2
464.0
469.9
484.0
For bidirectional type having VRWM of 60 volts and less, the IR limit is double.
For parts without A , the VBR is + 10% and Vc is 5% higher than with A parts.
© 2014 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/24/14
TransientVoltage Suppression Diodes
Axial Leaded – 30000W > 30KPA series
I-V Curve Characteristics
Bi-directional
Uni-directional
Ipp
IT
IR
Vc VBR
VR
V
Vc VBR
VR
IR
IT
V
VRVBR Vc
IR
IT
VF
Ipp
Ipp
PPPM Peak Pulse Power Dissipation -- Max power dissipation
VR Stand-off Voltage -- Maximum voltage that can be applied to theTVS without operation
VBR Breakdown Voltage -- Maximum voltage that flows though theTVS at a specified test current (IT)
VC Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current)
IR Reverse Leakage Current -- Current measured at VR
VF Forward Voltage Drop for Uni-directional
Ratings and Characteristic Curves (TA=25°C unless otherwise noted)
Figure 1 -TVSTransients ClampingWaveform
Figure 2 - Peak Pulse Power Rating Curve
1000
Voltage Transients
100
Voltage Across TVS
Current Through TVS
10
1
0.000001
0.00001
0.0001
0.001
td-Pulse Width (sec.)
Time
continues on next page.
© 2014 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/24/14
TransientVoltage Suppression Diodes
Axial Leaded – 30000W > 30KPA series
Ratings and Characteristic Curves (TA=25°C unless otherwise noted) (Continued)
Figure 3 - Pulse Derating Curve
Figure 4 - PulseWaveform
100
80
60
40
20
0
150
t =10µsec
T
=25°C
r
J
Pulse Width(td) is defined
as the point where the peak
current decays to 50% of I
PPM
Peak Value
I
100
PPM
Half Value
I
PPM
I
PPM
( )
2
50
0
10/1000µsec. Waveform
as defined by R.E.A
t
d
0
25
50
75
100
125
150
175
1.0
2.0
t-Time (ms)
3.0
4.0
0
TA-Ambient temperature (ºC)
Figure 5 -Typical Junction Capacitance
Figure 6 - Steady State Power Derating Curve
9
8
7
6
5
4
Bi-directional V= OV
10000
Uni-directional V= OV
Uni-directional @ VR
Bi-directional @ VR
100
1
3
L = 0.375” (9.5mm)
Lead Lengths
2
Tj=25C
f=1.0MHz
1
0
Vsig=50mVp-p
0
50
100
150
200
250
300
0
25 50 75 100 125 150 175 200
TL- Lead Temperature (ºC)
VBR - Reverse Breakdown Voltage (V)
Figure 7 - Maximum Non-Repetitive Peak Forward
Surge Current
450
400
350
300
250
200
150
100
50
0
1
10
100
Number of Cycles at 60 Hz
© 2014 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/24/14
TransientVoltage Suppression Diodes
Axial Leaded – 30000W > 30KPA series
Soldering Parameters
tp
Reflow Condition
Lead–free assembly
TP
Ramp-up
Critical Zone
to T
T
-Temperature Min (Ts(min)
)
150°C
L
P
TL
tL
Pre Heat -Temperature Max (Ts(max)
)
200°C
Ts(max)
-Time (min to max) (ts)
60 – 180 secs
Ramp-down
Ts(min)
Average ramp up rate (LiquidusTemp
(TL) to peak
ts
3°C/second max
Preheat
TS(max) toTL - Ramp-up Rate
3°C/second max
25˚C
t 25˚C to Peak
-Temperature (TL) (Liquidus) 217°C
Time (t)
Reflow
-Time (min to max) (ts)
60 – 150 seconds
PeakTemperature (TP)
260+0/-5 °C
Time within 5°C of actual peak
Temperature (tp)
Flow/Wave Soldering (Solder Dipping)
20 – 40 seconds
PeakTemperature :
DippingTime :
Soldering :
265OC
Ramp-down Rate
6°C/second max
8 minutes Max.
280°C
10 seconds
1 time
Time 25°C to peakTemperature (TP)
Do not exceed
Environmental Specifications
Physical Specifications
Weight
Case
0.07oz., 2.5g
HighTemp. Storage
HTRB
JESD22-A103
P600 molded plastic body over
passivated junction.
JESD22-A108
JESD22-A104
JESD22-A101
JESD22-B106
Color band denotes the cathode except
Bipolar.
Temperature Cycling
H3TRB
Polarity
MatteTin axial leads, solderable per
JESD22-B102.
Terminal
RSH
Dimensions
Cathode Band
(for Uni-directional products only)
Inches
Millimeters
Min Max
Dimensions
Min
Max
D
A
B
C
D
1.000
0.340
0.048
0.340
-
25.40
8.60
1.22
-
C
0.360
0.052
0.360
9.10
1.32
9.10
A
A
B
8.60
P600
© 2014 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/24/14
TransientVoltage Suppression Diodes
Axial Leaded – 30000W > 30KPA series
Part Numbering System
Part Marking System
30KPA xxxXXX
OPTION CODE:
BLANK ReelTape
-B Bulk Packaging
Cathode Band
YYWW
(for Uni-directional
products only)
TYPE CODE:
A
Uni-Directional (5%
V
BR VoltageTolerance)
VBR VoltageTolerance)
CA Bi-Directional (5%
Trace Code Marking
YY:Year Code
WW: Week Code
Littelfuse Logo
VR VOLTAGE
30KPAXXX
SERIES CODE
Product Type
Packing Options
Part Number
Component Package
Quantity
Packaging Option
Packaging Specification
EIA STD RS-296
30KPAxxxXX
P600
800
Tape & Reel
30KPAxxxXX-B
P600
100
Bulk
Littelfuse Spec.
Tape and Reel Specification
Off Center
either side
0.028(0.7)
2.56
(65.0)
2.063+0.079/-0.039
(53.0+2.0/-1.0)
0.236
(6.0)
0.047
(1.2)
0.394+/-0.020
(10.0+/-0.5)
Dimensions are in
inches/mm
13.0
(330.2)
3.0
(76.2)
0.68
(17. 27)
2.75
(69.85)
Direction of Feed
Recess Depth Max. 0.75 (19.05)
© 2014 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 01/24/14
相关型号：
30KPA300A
Trans Voltage Suppressor Diode, 30000W, 300V V(RWM), Unidirectional, 1 Element, Silicon, HALOGEN FREE AND ROHS COMPLIANT, PLASTIC, P600, 2 PIN
LITTELFUSE
30KPA300A-HR
Trans Voltage Suppressor Diode, 30000W, 300V V(RWM), Unidirectional, 1 Element, Silicon,
LITTELFUSE
30KPA300A-HRA
Trans Voltage Suppressor Diode, 30000W, 300V V(RWM), Unidirectional, 1 Element, Silicon, HALOGEN FREE AND ROHS COMPLIANT, PLASTIC, P600, 2 PIN
LITTELFUSE
30KPA300A-LF
Trans Voltage Suppressor Diode, 30000W, 300V V(RWM), Unidirectional, 1 Element, Silicon, ROHS COMPLIANT, PLASTIC PACKAGE-2
PROTEC
30KPA300CA
Trans Voltage Suppressor Diode, 30000W, 300V V(RWM), Bidirectional, 1 Element, Silicon, HALOGEN FREE AND ROHS COMPLIANT, PLASTIC, P600, 2 PIN
LITTELFUSE
©2020 ICPDF网 联系我们和版权申明