R0487YS10F [LITTELFUSE]
Silicon Controlled Rectifier,;型号: | R0487YS10F |
厂家: | LITTELFUSE |
描述: | Silicon Controlled Rectifier, |
文件: | 总12页 (文件大小:385K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Date:- 14 Oct, 2004
Data Sheet Issue:- 3
WESTCODE
An IXYS Company
Distributed Gate Thyristor
Type R0487YS10# to R0487YS14#
(Old Type Number: R210SH10-14)
Absolute Maximum Ratings
MAXIMUM
LIMITS
VOLTAGE RATINGS
UNITS
VDRM
VDSM
VRRM
VRSM
Repetitive peak off-state voltage, (note 1)
Non-repetitive peak off-state voltage, (note 1)
Repetitive peak reverse voltage, (note 1)
Non-repetitive peak reverse voltage, (note 1)
1000-1400
V
V
V
V
1000-1400
1000-1400
1100-1500
MAXIMUM
LIMITS
487
OTHER RATINGS
UNITS
IT(AV)M
IT(AV)M
IT(AV)M
IT(RMS)
IT(d.c.)
ITSM
Maximum average on-state current, Tsink=55°C, (note 2)
Maximum average on-state current. Tsink=85°C, (note 2)
Maximum average on-state current. Tsink=85°C, (note 3)
Nominal RMS on-state current, Tsink=25°C, (note 2)
D.C. on-state current, Tsink=25°C, (note 4)
Peak non-repetitive surge tp=10ms, Vrm=60%VRRM, (note 5)
Peak non-repetitive surge tp=10ms, Vrm≤10V, (note 5)
I2t capacity for fusing tp=10ms, Vrm=60%VRRM, (note 5)
I2t capacity for fusing tp=10ms, Vrm≤10V, (note 5)
Critical rate of rise of on-state current (repetitive), (Note 6)
Critical rate of rise of on-state current (non-repetitive), (Note 6)
Peak reverse gate voltage
A
A
321
184
A
982
A
802
A
4300
A
ITSM2
I2t
I2t
4700
A
92.5×103
110.5×103
500
A2s
A2s
A/µs
A/µs
V
(di/dt)cr
1000
VRGM
PG(AV)
PGM
5
Mean forward gate power
2
W
Peak forward gate power
30
W
Tj op
Operating temperature range
-40 to +125
-40 to +150
°C
°C
Tstg
Storage temperature range
Notes:-
1) De-rating factor of 0.13% per °C is applicable for Tj below 25°C.
2) Double side cooled, single phase; 50Hz, 180° half-sinewave.
3) Single side cooled, single phase; 50Hz, 180° half-sinewave.
4) Double side cooled.
5) Half-sinewave, 125°C Tj initial.
6) VD=67% VDRM, IFG=2A, tr≤0.5µs, Tcase=125°C.
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 1 of 12
October, 2004
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
Characteristics
PARAMETER
MIN.
TYP. MAX. TEST CONDITIONS (Note 1)
UNITS
VTM
VT0
rT
Maximum peak on-state voltage
Threshold voltage
-
-
-
2.7
1.738
0.943
-
ITM=1000A
V
V
-
Slope resistance
-
-
mΩ
V/µs
mA
mA
V
(dv/dt)cr Critical rate of rise of off-state voltage
200
-
VD=80% VDRM, Linear ramp, Gate o/c
Rated VDRM
IDRM
IRRM
VGT
IGT
VGD
IH
Peak off-state current
Peak reverse current
-
-
-
-
-
-
-
-
-
-
-
-
-
60
-
60
Rated VRRM
Gate trigger voltage
-
3.0
Tj=25°C
VD=10V, IT=3A
Gate trigger current
-
200
mA
V
Gate non-trigger voltage
Holding current
-
0.25 Rated VDRM
1000 Tj=25°C
1.0
-
mA
tgd
Gate controlled turn-on delay time
Turn-on time
0.4
1.0
90
40
45
1.9
VD=67% VDRM, ITM=2000A, di/dt=60A/µs,
µs
I
FG=2A, tr=0.5µs, Tj=25°C
tgt
2.0
Qrr
Qra
Irm
Recovered charge
-
55
-
µC
µC
A
Recovered charge, 50% Chord
Reverse recovery current
Reverse recovery time, 50% Chord
I
TM=550A, tp=500µs, di/dt=40A/µs, Vr=50V
trr
-
µs
ITM=550A, tp=500µs, di/dt=40A/µs, Vr=50V,
Vdr=80%VDRM, dVdr/dt=20V/µs
-
-
-
28
30
tq
Turn-off time (note 2)
µs
I
TM=550A, tp=500µs, di/dt=40A/µs, Vr=50V,
20
Vdr=80%VDRM, dVdr/dt=200V/µs
-
-
-
-
0.05 Double side cooled
K/W
K/W
kN
RthJK
Thermal resistance, junction to heatsink
0.1
9
Single side cooled
F
Mounting force
Weight
5
-
-
Wt
90
-
kg
Notes:-
1) Unless otherwise indicated Tj=125°C.
2) The required tq (specified with dVdr/dt=200V/µs) is represented by a ‘#’ in the device part number. See ordering information for
details of tq codes.
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 2 of 12
October, 2004
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
Notes on Ratings and Characteristics
1.0 Voltage Grade Table
V
DRM VDSM VRRM
VRSM
V
1100
1300
1500
VD VR
DC V
690
810
930
Voltage Grade
V
10
12
14
1000
1200
1400
2.0 Extension of Voltage Grades
This report is applicable to other and higher voltage grades when supply has been agreed by
Sales/Production.
3.0 Extension of Turn-off Time
This Report is applicable to other tq/re-applied dv/dt combinations when supply has been agreed by
Sales/Production.
4.0 Repetitive dv/dt
Higher dv/dt selections are available up to 1000V/µs on request.
5.0 De-rating Factor
A blocking voltage de-rating factor of 0.13%/°C is applicable to this device for Tj below 25°C.
6.0 Snubber Components
When selecting snubber components, care must be taken not to use excessively large values of snubber
capacitor or excessively small values of snubber resistor. Such excessive component values may lead to
device damage due to the large resultant values of snubber discharge current. If required, please consult
the factory for assistance.
7.0 Rate of rise of on-state current
The maximum un-primed rate of rise of on-state current must not exceed 1500A/µs at any time during
turn-on on a non-repetitive basis. For repetitive performance, the on-state rate of rise of current must not
exceed 1000A/µs at any time during turn-on. Note that these values of rate of rise of current apply to the
total device current including that from any local snubber network.
8.0 Gate Drive
The nominal requirement for a typical gate drive is illustrated below. An open circuit voltage of at least 30V
is assumed. This gate drive must be applied when using the full di/dt capability of the device.
IGM
4A/µs
IG
tp1
The magnitude of IGM should be between five and ten times IGT, which is shown on page 2. Its duration
(tp1) should be 20µs or sufficient to allow the anode current to reach ten times IL, whichever is greater.
Otherwise, an increase in pulse current could be needed to supply the necessary charge to trigger. The
‘back-porch’ current IG should remain flowing for the same duration as the anode current and have a
magnitude in the order of 1.5 times IGT.
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 3 of 12
October, 2004
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
9.0 Frequency Ratings
The curves illustrated in figures 10 to 18 are for guidance only and are superseded by the maximum
ratings shown on page 1.
10.0 Square wave ratings
These ratings are given for load component rate of rise of forward current of 100 and 500 A/µs.
11.0 Duty cycle lines
The 100% duty cycle is represented on all the ratings by a straight line. Other duties can be included as
parallel to the first.
12.0 Maximum Operating Frequency
The maximum operating frequency is set by the on-state duty, the time required for the thyristor to turn off
(tq) and for the off-state voltage to reach full value (tv), i.e.
1
f max =
tpulse +tq +tv
13.0 On-State Energy per Pulse Characteristics
These curves enable rapid estimation of device dissipation to be obtained for conditions not covered by
the frequency ratings.
Let Ep be the Energy per pulse for a given current and pulse width, in joules
Let Rth(JK) be the steady-state d.c. thermal resistance (junction to sink)
and TK be the heat sink temperature.
Then the average dissipation will be:
WAV = EP f and TK (max.) =125 −
WAV Rth
(
JK
)
14.0 Reverse recovery ratings
(i) Qra is based on 50% Irm chord as shown in Fig. 1
Fig. 1
(ii) Qrr is based on a 150µs integration time i.e.
150µs
Qrr = irr .dt
∫
0
(iii)
t1
K Factor =
t2
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 4 of 12
October, 2004
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
15.0 Reverse Recovery Loss
15.1 Determination by Measurement
From waveforms of recovery current obtained from a high frequency shunt (see Note 1, Page 5) and
reverse voltage present during recovery, an instantaneous reverse recovery loss waveform must be
constructed. Let the area under this waveform be E joules per pulse. A new heat sink temperature can
then be evaluated from the following:
TK (new) = TK (original ) − E
k + f Rth
(
JK
)
Where k=0.227 (°C/W)/s
E = Area under reverse loss waveform per pulse in joules (W.s.)
f = rated frequency Hz at the original heat sink temperature.
Rth(JK) = d.c. thermal resistance (°C/W).
The total dissipation is now given by:
W(TOT) = W(original) + E f
15.2 Determination without Measurement
In circumstances where it is not possible to measure voltage and current conditions, or for design
purposes, the additional losses E in joules may be estimated as follows.
Let E be the value of energy per reverse cycle in joules (curves in Figure 9).
Let f be the operating frequency in Hz
TK
= TK
−
)
(
E Rth f
)
(
new
)
(
original
Where TK (new) is the required maximum heat sink temperature and
TK (original) is the heat sink temperature given with the frequency ratings.
A suitable R-C snubber network is connected across the thyristor to restrict the transient reverse voltage
to a peak value (Vrm) of 67% of the maximum grade. If a different grade is being used or Vrm is other than
67% of Grade, the reverse loss may be approximated by a pro rata adjustment of the maximum value
obtained from the curves.
NOTE 1- Reverse Recovery Loss by Measurement
This thyristor has a low reverse recovered charge and peak reverse recovery current. When measuring
the charge, care must be taken to ensure that:
(a) a.c. coupled devices such as current transformers are not affected by prior passage of high
amplitude forward current.
(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope
to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal
(c) Measurement of reverse recovery waveform should be carried out with an appropriate critically
damped snubber, connected across diode anode to cathode. The formula used for the calculation
of this snubber is shown below:
Vr
= Commutating source voltage
Vr
R2 = 4
Where: CS = Snubber capacitance
di
CS
R
= Snubber resistance
dt
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 5 of 12
October, 2004
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
16.0 Computer Modelling Parameters
16.1 Calculating VT using ABCD Coefficients
The on-state characteristic IT vs VT, on page 7 is represented in two ways;
(i)
(ii)
the well established VT0 and rT tangent used for rating purposes and
a set of constants A, B, C, D, forming the coefficients of the representative equation for VT in
terms of IT given below:
VT = A+ B ln
(
IT + C IT + D IT
)
The constants, derived by curve fitting software, are given in this report for hot and cold characteristics
where possible. The resulting values for VT agree with the true device characteristic over a current range,
which is limited to that plotted.
25°C Coefficients
125°C Coefficients
A
B
C
D
2.934606
0.02319972
7.8776×10-4
-0.0191799
A
B
C
D
1.73452
-0.06566122
5.7985×10-4
0.02661417
16.2 D.C. Thermal Impedance Calculation
p=n
−t
τ p
r = r 1− e
∑
t
p
p=1
Where p = 1 to n, n is the number of terms in the series.
t = Duration of heating pulse in seconds.
rt = Thermal resistance at time t.
rp = Amplitude of pth term.
τp = Time Constant of rth term.
D.C. Double Side Cooled
Term
rp
1
2
3
4
0.0200056
0.3391689
9.923438×10-3
0.01433715
0.03562131
4.284403×10-3
2.562946×10-3
0.1269073
τp
D.C. Single Side Cooled
3
Term
rp
1
2
4
5
0.06157697
2.136132
8.431182×10-3
0.01031315
0.1512408
0.01613806
0.04244
5.181088×10-3
2.889595×10-3
1.212898
τp
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 6 of 12
October, 2004
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
Curves
Figure 1 - On-state characteristics of Limit device
Figure 2 - Transient thermal impedance
10000
1
R0487YS10#-14#
R0487YS10#-14#
Issue 3
Issue 3
25°C
125°C
SSC 0.1K/W
0.1
DSC 0.05K/W
1000
0.01
0.001
100
0.0001
0
1
2
3
4
5
6
7
0.000001
0.0001
0.01
1
100
Instantaneous on-state voltage - VT (V)
Time (s)
`
Figure 3 - Gate characteristics - Trigger limits
Figure 4 - Gate characteristics - Power curves
20
8
R0487YS10#-14#
Issue 3
R0487YS10#-14#
Issue 3
Tj=25°C
18
Tj=25°C
7
Max VG dc
16
6
14
12
10
8
Max VG dc
5
4
3
2
1
0
IGT, VGT
PG Max 30W dc
6
4
PG 2W dc
2
Min VG dc
0.5
Min VG dc
IGD, VGD
0.1
0
0
2
4
6
8
10
0
0.2
0.3
0.4
0.6
Gate Trigger Current - IGT (A)
Gate Trigger Current - IGT (A)
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 7 of 12
October, 2004
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
Figure 5 - Total recovered charge, Qrr
Figure 6 - Recovered charge, Qra (50% chord)
1000
1000
R0487YS10#-14#
Issue 3
R0487YS10#-14#
Issue 3
Tj = 125°C
Tj = 125°C
2000A
1500A
1000A
550A
2000A
1500A
1000A
550A
100
100
10
10
10
100
1000
10
100
Commutation rate - di/dt (A/µs)
1000
Commutation rate - di/dt (A/µs)
Figure 7 - Peak reverse recovery current, Irm
Figure 8 - Maximum recovery time, trr (50% chord)
10
1000
R0487YS10#-14#
Issue 3
R0487YS10#-14#
Issue 3
Tj = 125°C
Tj = 125°C
2000A
1500A
1000A
550A
100
2000A
1500A
1000A
500A
1
10
10
100
1000
10
100
1000
Commutation rate - di/dt (A/µs)
Commutation rate - di/dt (A/µs)
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 8 of 12
October, 2004
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
Figure 9 – Reverse recovery energy per pulse
Figure 10 - Sine wave energy per pulse
100
1.00E+02
R0487YS10#-14#
R0487YS10#-14#
Issue 3
Issue 3
2000A
1000A
Tj = 125°C
Vrm = 67% VRRM
Tj=125°C
Ω
0.1µF, 10 snubber
500A
200A
1.00E+01
3kA
2kA
1.00E+00
10
1kA
1.00E-01
500A
250A
1.00E-02
1
1.00E-05
1.00E-04
1.00E-03
1.00E-02
1
10
100
1000
Pulse width (s)
Commutation rate - di/dt (A/µs)
Figure 11 – Square wave energy per pulse
Figure 12 - Square wave energy per pulse
1.00E+03
1.00E+03
R0487YS10#-14#
Issue 3
R0487YS10#-14#
Issue 3
di/dt=500A/µs
di/dt=100A/µs
Tj=125°C
Tj=125°C
1.00E+02
1.00E+01
1.00E+02
3kA
2kA
1.00E+01
1.00E+00
3kA
2kA
1.00E+00
1kA
1kA
500A
250A
1.00E-01
500A
1.00E-01
250A
1.00E-02
1.00E-02
1.00E-05
1.00E-04
1.00E-03
1.00E-02
1.00E-05
1.00E-04
1.00E-03
1.00E-02
Pulse width (s)
Pulse width (s)
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 9 of 12
October, 2004
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
Figure 13 - Sine wave frequency ratings
Figure 14 - Sine wave frequency ratings
1.00E+05
1.00E+05
R0487YS10#-14#
Issue 3
R0487YS10#-14#
Issue 3
Tk=55°C
Tk=85°C
250A
500A
250A
100% Duty Cycle
1.00E+04
500A
1.00E+04
1.00E+03
1.00E+02
1.00E+01
100% Duty Cycle
1kA
1kA
1.00E+03
2kA
2kA
3kA
1.00E+02
3kA
1.00E+01
1.00E+00
1.00E-05
1.00E-04
1.00E-03
1.00E-02
1.00E-05
1.00E-04
1.00E-03
1.00E-02
Pulse Width (s)
Pulse width (s)
Figure 15 - Square wave frequency ratings
Figure 16 - Square wave frequency ratings
1.00E+05
1.00E+05
R0487YS10#-14#
Issue 3
R0487YS10#-14#
Issue 3
di/dt=100A/µs
Tk=55°C
di/dt=500A/µs
Tk=55°C
250A
100% Duty Cycle
250A
500A
1.00E+04
1.00E+03
1.00E+02
1.00E+01
1.00E+00
1.00E+04
1.00E+03
1.00E+02
1.00E+01
1.00E+00
500A
1kA
100% Duty Cycle
2kA
1kA
3kA
2kA
3kA
1.00E-05
1.00E-04
1.00E-03
1.00E-02
1.00E-05
1.00E-04
1.00E-03
1.00E-02
Pulse width (s)
Pulse width (s)
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 10 of 12
October, 2004
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
Figure 17 - Square wave frequency ratings
Figure 18 - Square wave frequency ratings
1.00E+05
1.00E+05
R0487YS10#-14#
Issue 3
R0487YS10#-14#
Issue 3
di/dt=100A/µs
Tk=85°C
di/dt=500A/µs
Tk=85°C
100% Duty Cycle
1.00E+04
100% Duty Cycle
250A
500A
250A
1.00E+04
1.00E+03
1.00E+02
1.00E+01
500A
1kA
1.00E+03
1.00E+02
1.00E+01
1.00E+00
1kA
2kA
2kA
3kA
3kA
1.00E-05
1.00E-04
1.00E-03
1.00E-02
1.00E-05
1.00E-04
1.00E-03
1.00E-02
Pulse width (s)
Pulse width (s)
Figure 19 - Maximum surge and I2t Ratings
Gate may temporarily lose control of conduction angle
100000
10000
1000
1.00E+06
1.00E+05
1.00E+04
I2t: VRRM≤10V
R0487YS10#-14#
Issue 3
I2t: 60% VRRM
Tj (initial) = 125°C
ITSM: VRRM≤10V
ITSM: 60% VRRM
1
3
5
10
1
5
10
50 100
Duration of surge (ms)
Duration of surge (cycles @ 50Hz)
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 11 of 12
October, 2004
WESTCODE An IXYS Company
Distributed Gate Thyristor types R0487YS10# to R0487YS14#
Outline Drawing & Ordering Information
101A335
ORDERING INFORMATION
(Please quote 10 digit code as below)
R0487
YS
♦ ♦
#
Fixed
Type Code
Fixed
Outline Code
Fixed Voltage Code
VDRM/100
tq Code
D=20µs, E=25µs, F=30µs
10-14
Typical order code: R0487YS14E – 1400V VRRM/VDRM, 25µs tq, 15.1mm clamp height capsule.
IXYS Semiconductor GmbH
Westcode Semiconductors Ltd
Edisonstraße 15
Langley Park Way, Langley Park,
D-68623 Lampertheim
Tel: +49 6206 503-0
Fax: +49 6206 503-627
E-mail: marcom@ixys.de
Chippenham, Wiltshire, SN15 1GE.
Tel: +44 (0)1249 444524
Fax: +44 (0)1249 659448
E-mail: WSL.sales@westcode,com
WESTCODE
An IXYS Company
IXYS Corporation
3540 Bassett Street
Santa Clara CA 95054 USA
Tel: +1 (408) 982 0700
Fax: +1 (408) 496 0670
E-mail: sales@ixys.net
Westcode Semiconductors Inc
3270 Cherry Avenue
Long Beach CA 90807 USA
Tel: +1 (562) 595 6971
Fax: +1 (562) 595 8182
E-mail: WSI.sales@westcode.com
www.westcode.com
www.ixys.com
The information contained herein is confidential and is protected by Copyright. The information may not be used or disclosed
except with the written permission of and in the manner permitted by the proprietors Westcode Semiconductors Ltd.
© Westcode Semiconductors Ltd.
In the interest of product improvement, Westcode reserves the right to change specifications at any time without prior notice.
Devices with a suffix code (2-letter, 3-letter or letter/digit/letter combination) added to their generic code are not necessarily
subject to the conditions and limits contained in this report.
Data Sheet. Type R0487YS10# to R0487YS14# Issue 3
Page 12 of 12
October, 2004
相关型号:
R0487YS12#
Silicon Controlled Rectifier, 1200V V(DRM), 1200V V(RRM), 1 Element, 101A335, 3 PIN
LITTELFUSE
R0487YS12D
Silicon Controlled Rectifier, 982A I(T)RMS, 1200V V(DRM), 1200V V(RRM), 1 Element, 101A335, 3 PIN
LITTELFUSE
R0487YS12E
Silicon Controlled Rectifier, 982A I(T)RMS, 1200V V(DRM), 1200V V(RRM), 1 Element, 101A335, 3 PIN
LITTELFUSE
R0487YS12F
Silicon Controlled Rectifier, 982A I(T)RMS, 1200V V(DRM), 1200V V(RRM), 1 Element, 101A335, 3 PIN
LITTELFUSE
R0487YS14#
Silicon Controlled Rectifier, 1400V V(DRM), 1400V V(RRM), 1 Element, 101A335, 3 PIN
LITTELFUSE
R0487YS14D
Silicon Controlled Rectifier, 982A I(T)RMS, 1400V V(DRM), 1400V V(RRM), 1 Element, 101A335, 3 PIN
IXYS
R0487YS14D
Silicon Controlled Rectifier, 982A I(T)RMS, 1400V V(DRM), 1400V V(RRM), 1 Element, 101A335, 3 PIN
LITTELFUSE
R0487YS14E
Silicon Controlled Rectifier, 982A I(T)RMS, 1400V V(DRM), 1400V V(RRM), 1 Element, 101A335, 3 PIN
IXYS
R0487YS14E
Silicon Controlled Rectifier, 982A I(T)RMS, 1400V V(DRM), 1400V V(RRM), 1 Element, 101A335, 3 PIN
LITTELFUSE
R0487YS14F
Silicon Controlled Rectifier, 982A I(T)RMS, 1400V V(DRM), 1400V V(RRM), 1 Element, 101A335, 3 PIN
LITTELFUSE
©2020 ICPDF网 联系我们和版权申明