LT1721IS#PBF [Linear]
LT1721 - Quad, 4.5ns, Single Supply 3V/5V Comparators with Rail-to-Rail Outputs; Package: SO; Pins: 16; Temperature Range: -40°C to 85°C;型号: | LT1721IS#PBF |
厂家: | Linear |
描述: | LT1721 - Quad, 4.5ns, Single Supply 3V/5V Comparators with Rail-to-Rail Outputs; Package: SO; Pins: 16; Temperature Range: -40°C to 85°C |
文件: | 总28页 (文件大小:320K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LT1720/LT1721
Dual/Quad,
4.5ns, Single Supply
3V/5V Comparators
with Rail-to-Rail Outputs
U
FEATURES
DESCRIPTIO
The LT®1720/LT1721 are UltraFastTM dual/quad compara-
tors optimized for single supply operation, with a supply
voltage range of 2.7V to 6V. The input voltage range extends
from100mVbelowgroundto1.2Vbelowthesupplyvoltage.
Internal hysteresis makes the LT1720/LT1721 easy to use
even with slow moving input signals. The rail-to-rail outputs
directly interface to TTL and CMOS. Alternatively, the sym-
metric output drive can be harnessed for analog applications
or for easy translation to other single supply logic levels.
■
UltraFast: 4.5ns at 20mV Overdrive
7ns at 5mV Overdrive
■
Low Power: 4mA per Comparator
■
Optimized for 3V and 5V Operation
■
Pinout Optimized for High Speed Ease of Use
■
Input Voltage Range Extends 100mV
Below Negative Rail
■
TTL/CMOS Compatible Rail-to-Rail Outputs
■
Internal Hysteresis with Specified Limits
■
Low Dynamic Current Drain; 15µA/(V-MHz),
The LT1720 is available in the 8-pin MSOP and SO packages;
three pins per comparator plus power and ground. The
LT1721 is available in the 16-pin SSOP and S packages.
Dominated by Load In Most Circuits
U
APPLICATIO S
ThepinoutsoftheLT1720/LT1721minimizeparasiticeffects
byplacingthemostsensitiveinputs(inverting)awayfromthe
outputs, shieldedbythepowerrails. TheLT1720/LT1721are
ideal for systems where small size and low power are
paramount.
■
High Speed Differential Line Receiver
■
Crystal Oscillator Circuits
■
Window Comparators
Threshold Detectors/Discriminators
Pulse Stretchers
Zero-Crossing Detectors
High Speed Sampling Circuits
■
, LTC and LT are registered trademarks of Linear Technology Corporation.
UltraFast is a trademark of Linear Technology Corporation.
■
■
■
U
TYPICAL APPLICATIO
2.7V to 6V Crystal Oscillator with TTL/CMOS Output
Propagation Delay vs Overdrive
8
2.7V TO 6V
25°C
1MHz TO 10MHz
7
6
5
4
3
2
1
0
V
V
C
= 100mV
= 10pF
STEP
CC
LOAD
2k
CRYSTAL (AT-CUT)
= 5V
RISING EDGE
(t
220Ω
)
PDLH
620Ω
GROUND
CASE
+
FALLING EDGE
(t
C1
)
PDHL
OUTPUT
1/2 LT1720
–
2k
1.8k
1720/21 TA01
0.01µF
10
20
OVERDRIVE (mV)
40
0
50
30
1720/21 TA02
1
LT1720/LT1721
W W U W
ABSOLUTE MAXIMUM RATINGS (Note 1)
Storage Temperature Range ................. –65°C to 150°C
Operating Temperature Range
Supply Voltage, VCC to GND ...................................... 7V
Input Current ...................................................... ±10mA
Output Current (Continuous) ............................. ±20mA
Junction Temperature........................................... 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
C Grade .................................................. 0°C to 70°C
I Grade .............................................. –40°C to 85°C
U
W U
PACKAGE/ORDER INFORMATION
TOP VIEW
–IN A
+IN A
GND
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
–IN D
+IN D
TOP VIEW
TOP VIEW
V
CC
+IN A
–IN A
–IN B
+IN B
1
2
3
4
8
7
6
5
V
CC
+IN A
–IN A
–IN B
+IN B
1
2
3
4
8 V
CC
OUT A
OUT B
GND
OUT D
OUT C
7 OUT A
6 OUT B
5 GND
OUT A
OUT B
GND
V
CC
MS8 PACKAGE
8-LEAD PLASTIC MSOP
+IN B
–IN B
+IN C
–IN C
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 230°C/ W
GN PACKAGE
16-LEAD NARROW
PLASTIC SSOP
S PACKAGE
16-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 200°C/ W
TJMAX = 150°C, θJA = 135°C/ W (GN)
TJMAX = 150°C, θJA = 115°C/ W (S)
ORDER PART
NUMBER
MS8
PART MARKING
ORDER PART
NUMBER
S8
ORDER PART
NUMBER
GN
PART MARKING
PART MARKING
LT1720CMS8
LTDS
LT1720CS8
LT1720IS8
1720
1720I
LT1721CGN
LT1721CS
LT1721IGN
LT1721IS
1721
1721I
Consult factory for Military grade parts.
The ● denotes specifications that apply over the full operating temperature
ELECTRICAL CHARACTERISTICS
range, otherwise specifications are at TA = 25°C. VCC = 5V, VCM = 1V, COUT = 10pF, VOVERDRIVE = 20mV, unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN
2.7
TYP
MAX
UNITS
V
V
V
Supply Voltage
●
●
6
V
V
CC
Common Mode Voltage Range
Input Trip Points
(Note 2)
(Note 3)
–0.1
V
– 1.2
CC
CMR
TRIP
+
–
–2.0
–3.0
5.5
6.5
mV
mV
●
●
V
V
V
Input Trip Points
(Note 3)
(Note 3)
(Note 3)
–5.5
–6.5
2.0
3.0
mV
mV
TRIP
OS
Input Offset Voltage
1.0
3.0
4.5
mV
mV
●
●
●
Input Hysteresis Voltage
Input Offset Voltage Drift
2.0
3.5
10
5.0
mV
HYST
∆V /∆T
µV/°C
OS
2
LT1720/LT1721
The ● denotes specifications that apply over the full operating temperature
ELECTRICAL CHARACTERISTICS
range, otherwise specifications are at TA = 25°C. VCC = 5V, VCM = 1V, COUT = 10pF, VOVERDRIVE = 20mV, unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
0
UNITS
µA
I
I
Input Bias Current
●
●
●
●
–6
B
Input Offset Current
0.6
µA
OS
CMRR
PSRR
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Voltage Gain
(Note 4)
(Note 5)
(Note 6)
55
65
70
80
∞
dB
dB
A
V
V
V
+
Output High Voltage
Output Low Voltage
I
I
= 4mA, V = V
+ 10mV
●
●
V – 0.4
CC
V
V
OH
OL
SOURCE
IN
TRIP
–
= 10mA, V = V
– 10mV
0.4
SINK
IN
TRIP
I
t
t
Supply Current (Per Comparator)
V
V
= 5V
= 3V
●
●
4
3.5
7
6
mA
mA
CC
CC
CC
Propagation Delay
Propagation Delay
V
= 20mV (Note 7)
4.5
7
6.5
8.0
ns
ns
PD20
PD5
OVERDRIVE
●
●
V
= 5mV (Notes 7, 8)
10
13
ns
ns
OVERDRIVE
∆t
Differential Propagation Delay
Propagation Delay Skew
Output Rise Time
(Note 9) Between Channels
0.3
0.5
2.5
2.2
1.0
1.5
ns
ns
ns
ns
PD
+
–
t
t
t
t
(Note 10) Between t /t
SKEW
PD PD
10% to 90%
90% to 10%
r
Output Fall Time
f
+
–
Output Timing Jitter
V
V
= 1.2V (6dBm), Z = 50Ω
t
t
15
11
ps
ps
JITTER
IN
P-P
IN
PD
RMS
RMS
= 2V, f = 20MHz
CM
PD
f
Maximum Toggle Frequency
V
V
= 50mV, V = 3V
70.0
62.5
MHz
MHz
MAX
OVERDRIVE
OVERDRIVE
CC
= 50mV, V = 5V
CC
Note 1: Absolute Maximum Ratings are those values beyond which the
life of a device may be impaired.
Note 7: Propagation delay measurements made with 100mV steps.
Overdrive is measured relative to VTRIP .
±
Note 2: If one input is within these common mode limits, the other
input can go outside the common mode limits and the output will be
valid.
Note 3: The LT1720/LT1721 comparators include internal hysteresis.
The trip points are the input voltage needed to change the output state
Note 8: tPD cannot be measured in automatic handling equipment with
low values of overdrive. The LT1720/LT1721 are 100% tested with a
100mV step and 20mV overdrive. Correlation tests have shown that
tPD limits can be guaranteed with this test, if additional DC tests are
performed to guarantee that all internal bias conditions are correct.
Note 9: Differential propagation delay is defined as the larger of the
two:
+
in each direction. The offset voltage is defined as the average of VTRIP
and VTRIP–, while the hysteresis voltage is the difference of these two.
Note 4: The common mode rejection ratio is measured with VCC = 5V
∆tPDLH = tPDLH(MAX) – tPDLH(MIN)
∆tPDHL = tPDHL(MAX) – tPDHL(MIN)
where (MAX) and (MIN) denote the maximum and minimum values of
a given measurement across the different comparator channels.
and is defined as the change in offset voltage measured from VCM
–0.1V to VCM = 3.8V, divided by 3.9V.
=
Note 5: The power supply rejection ratio is measured with VCM = 1V
and is defined as the change in offset voltage measured from VCC
2.7V to VCC = 6V, divided by 3.3V.
Note 6: Because of internal hysteresis, there is no small-signal region
in which to measure gain. Proper operation of internal circuity is
ensured by measuring VOH and VOL with only 10mV of overdrive.
=
Note 10: Propagation Delay Skew is defined as:
tSKEW = |tPDLH – tPDHL
|
3
LT1720/LT1721
TYPICAL PERFORMANCE CHARACTERISTICS
W
U
Input Offset and Trip Voltages
vs Supply Voltage
Input Offset and Trip Voltages
vs Temperature
Input Common Mode Limits
vs Temperature
3
2
3
2
4.2
4.0
V
CC
= 5V
+
+
V
TRIP
V
TRIP
3.8
3.6
0.2
0
1
0
1
V
V
OS
OS
0
–1
–2
–3
–1
–2
–3
–
–
V
V
TRIP
TRIP
–0.2
25°C
CM
V
= 1V
–0.4
–50 –25
0
25
50
75 100 125
4.5
SUPPLY VOLTAGE (V)
5.5 6.0
50
TEMPERATURE (°C)
100 125
2.5 3.0
3.5 4.0
5.0
–50
25
75
–25
0
TEMPERATURE (°C)
1720/21 G02
1720/21 G01
1720/21 G03
Input Current
vs Differential Input Voltage
Quiescent Supply Current
vs Temperature
Quiescent Supply Current
vs Supply Voltage
7
6
5
4
3
2
1
0
2
1
6.0
25°C
CC
V
= 5V
125°C
5.5
5.0
0
–1
–2
–3
–4
–5
–6
–7
4.5
4.0
3.5
3.0
2.5
25°C
V
CC
= 5V
–55°C
V
CC
= 3V
2.0
0
2
3
4
5
6
7
–25
0
50
75 100 125
1
–50
25
–5 –4 –3 –2 –1
0
5
1
2
3
4
SUPPLY VOLTAGE (V)
DIFFERENTIAL INPUT VOLTAGE (V)
TEMPERATURE (˚C)
1720/21 G06
1720/21 G05
1720/21 G04
Propagation Delay
vs Load Capacitance
Propagation Delay
vs Temperature
Propagation Delay
vs Supply Voltage
9
8.0
5.0
4.5
4.0
t
25°C
STEP
PDLH
CM
STEP
LOAD
25°C
STEP
RISING EDGE
(t
V
V
C
= 1V
= 100mV
= 10pF
8
7
6
5
4
3
2
1
0
V
= 100mV
V
= 100mV
7.5
7.0
)
PDLH
OVERDRIVE = 20mV
= 5V
OVERDRIVE = 20mV
= 10pF
V
= 3V
CC
V
CC
C
LOAD
V
= 5V
6.5
6.0
5.5
5.0
4.5
CC
FALLING EDGE
(t
RISING EDGE
(t
)
PDHL
)
OVERDRIVE = 5mV
OVERDRIVE = 20mV
PDLH
V
CC
= 5V
FALLING EDGE
(t
PDHL
)
V
CC
= 3V
4.0
10
20
40
0
50
30
4.5
5.5
6.0
–25
0
50
75 100 125
2.5 3.0
3.5 4.0
5.0
–50
25
OUTPUT LOAD CAPACITANCE (pF)
TEMPERATURE (°C)
SUPPLY VOLTAGE (V)
1720/21 G07
1720/21 G08
1720/21 G09
4
LT1720/LT1721
W
U
TYPICAL PERFORMANCE CHARACTERISTICS
Output High Voltage
vs Load Current
Output Low Voltage
vs Load Current
Supply Current vs Frequency
0.5
0.4
0.3
0.2
0.1
0.0
–0.2
–0.4
–0.6
–0.8
–1.0
10
9
25°C
CC
V
V
V
= 5V
= 1V
V
V
V
= 5V
= 1V
CC
CM
IN
CC
CM
IN
V
= 5V
125°C
= 15mV
= –15mV
125°C
125°C
= 2.7V
8
V
CC
–55°C
C
= 20pF
LOAD
25°C
7
6
5
4
3
25°C
–55°C
NO LOAD
25°C
= 2.7V
V
CC
4
8
12
16
20
10
20
FREQUENCY (MHz)
40
0
4
8
12
16
20
0
0
30
OUTPUT SINK CURRENT (mA)
OUTPUT SOURCE CURRENT (mA)
1720/21 G10
1720/21 G11
1720/21 G12
U
U
U
PIN FUNCTIONS
LT1720
LT1721
–IN A (Pin 1): Inverting Input of Comparator A.
+IN A (Pin 1): Noninverting Input of Comparator A.
–IN A (Pin 2): Inverting Input of Comparator A.
–IN B (Pin 3): Inverting Input of Comparator B.
+IN B (Pin 4): Noninverting Input of Comparator B.
GND (Pin 5): Ground.
+IN A (Pin 2): Noninverting Input of Comparator A.
GND (Pins 3, 6): Ground.
OUT A (Pin 4): Output of Comparator A.
OUT B (Pin 5): Output of Comparator B.
OUT B (Pin 6): Output of Comparator B.
OUT A (Pin 7): Output of Comparator A.
VCC (Pin 8): Positive Supply Voltage.
+IN B (Pin 7): Noninverting Input of Comparator B.
–IN B (Pin 8): Inverting Input of Comparator B.
–IN C (Pin 9): Inverting Input of Comparator C.
+IN C (Pin 10): Noninverting Input of Comparator C.
VCC (Pins 11, 14): Positive Supply Voltage.
OUT C (Pin 12): Output of Comparator C.
OUT D (Pin 13): Output of Comparator D.
+IN D (Pin 15): Noninverting Input of Comparator D.
–IN D (Pin 16): Inverting Input of Comparator D.
5
LT1720/LT1721
TEST CIRCUITS
±VTRIP Test Circuit
15V
P-P
LTC203
BANDWIDTH-LIMITED
TRIANGLE WAVE
~
1kHz
14
15
3
2
V
CC
0.1µF
+
1000 × V
TRIP
50k
10nF
1µF
10k
+
–
16
9
1
8
50Ω
50Ω
1/2 LT1112
200k
+
–
1000 × V
HYST
DUT
1/2 LT1720 OR
1/4 LT1721
V
CM
11
10
6
7
1000 × V
OS
10k
LTC203
3
2
14
15
1/2 LT1638
+
–
1000 × V
TRIP
100k
100k
1µF
10nF
–
1
8
16
9
+
–
2.4k
100k
100k
1/2 LT1638
1/2 LT1112
+
–
0.15µF
6
7
11
10
1720/21 TC01
NOTES: LT1638, LT1112, LTC203s ARE POWERED FROM ±15V.
200kΩ PULL-DOWN PROTECTS LTC203 LOGIC INPUTS
WHEN DUT IS NOT POWERED
Response Time Test Circuit
+V – V
CC
CM
0V
DUT
1/2 LT1720 OR
1/4 LT1721
–100mV
0.01µF
+
–
25Ω
10 × SCOPE PROBE
(C ≈ 10pF)
25Ω
50k
IN
0.01µF
50Ω
V1*
0.1µF
130Ω
400Ω
PULSE
IN
2N3866
0V
1N5711
–V
+
CM
–3V
50Ω
750Ω
*V1 = –1000 • (OVERDRIVE + V
TRIP
)
NOTE: RISING EDGE TEST SHOWN.
FOR FALLING EDGE, REVERSE LT1720 INPUTS
1720/21 TC02
–5V
6
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
Input Voltage Considerations
Input Protection
The LT1720/LT1721 are specified for a common mode
range of –100mV to 3.8V when used with a single 5V
supply. In general the common mode range is 100mV
below ground to 1.2V below VCC. The criterion for this
common mode limit is that the output still responds
correctly to a small differential input signal. Also, if one
input is within the common mode limit, the other input
signal can go outside the common mode limits, up to the
absolute maximum limits (a diode drop past either rail at
10mA input current) and the output will retain the correct
polarity.
The input stage is protected against damage from large
differential signals, up to and beyond a differential voltage
equal to the supply voltage, limited only by the absolute
maximum currents noted. External input protection cir-
cuitry is only needed if currents would otherwise exceed
these absolute maximums. The internal catch diodes can
conduct current up to these rated maximums without
latchup, even when the supply voltage is at the absolute
maximum rating.
The LT1720/LT1721 input stage has general purpose
internalESDprotectionforthehumanbodymodel.Foruse
as a line receiver, additional external protection may be
required. As with most integrated circuits, the level of
immunity to ESD is much greater when residing on a
printed circuit board where the power supply decoupling
capacitance will limit the voltage rise caused by an ESD
pulse.
When either input signal falls below the negative common
mode limit, the internal PN diode formed with the sub-
strate can turn on, resulting in significant current flow
through the die. An external Schottky clamp diode
between the input and the negative rail can speed up
recovery from negative overdrive by preventing the sub-
strate diode from turning on.
Input Bias Current
When both input signals are below the negative common
mode limit, phase reversal protection circuitry prevents
false output inversion to at least –400mV common mode.
However, the offset and hysteresis in this mode will
increasedramatically,toasmuchas15mVeach.Theinput
bias currents will also increase.
Inputbiascurrentismeasuredwithbothinputsheldat1V.
As with any PNP differential input stage, the LT1720/
LT1721 bias current flows out of the device. With a
differential input voltage of even just 100mV or so, there
will be zero bias current into the higher of the two inputs,
while the current flowing out of the lower input will be
twice the measured bias current. With more than two
diode drops of differential input voltage, the LT1720/
LT1721’s input protection circuitry activates, and current
out of the lower input will increase an additional 30% and
there will be a small bias current into the higher of the two
input pins, of 4µA or less. See the Typical Performance
curve “Input Current vs Differential Input Voltage.”
When both input signals are above the positive common
mode limit, the input stage will become debiased and the
output polarity will be random. However, the internal
hysteresis will hold the output to a valid logic level, and
because the biasing of each comparator is completely
independent, there will be no impact on any other com-
parator. When at least one of the inputs returns to within
thecommonmodelimits,recoveryfromthisstatewilltake
as long as 1µs.
High Speed Design Considerations
The propagation delay does not increase significantly
whendrivenwithlargedifferentialvoltages.However,with
low levels of overdrive, an apparent increase may be seen
with large source resistances due to an RC delay caused
by the 2pF typical input capacitance.
Application of high speed comparators is often plagued
by oscillations. The LT1720/LT1721 have 4mV of internal
hysteresis, which will prevent oscillations as long as
parasitic output to input feedback is kept below 4mV.
7
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
However, with the 2V/ns slew rate of the LT1720/LT1721
outputs, a 4mV step can be created at a 100Ω input
source with only 0.02pF of output to input coupling. The
pinouts of the LT1720/LT1721 have been arranged to
minimize problems by placing the most sensitive inputs
(inverting) away from the outputs, shielded by the power
rails. The input and output traces of the circuit board
should also be separated, and the requisite level of
isolationisreadilyachievedifatopsidegroundplaneruns
betweentheoutputsandtheinputs. Formultilayerboards
where the ground plane is internal, a topside ground or
supply trace should be run between the inputs and
outputs, as illustrated in Figure 1.
The supply bypass should include an adjacent
10nF ceramic capacitor and a 2.2µF tantalum capacitor no
farther than 5cm away; use more capacitance if driving
more than 4mA loads. To prevent oscillations, it is helpful
tobalancetheimpedanceattheinvertingandnoninverting
inputs; source impedances should be kept low, preferably
1kΩ or less.
The outputs of the LT1720/LT1721 are capable of very
high slew rates. To prevent overshoot, ringing and other
problems with transmission line effects, keep the output
traces shorter than 10cm, or be sure to terminate the lines
to maintain signal integrity. The LT1720/LT1721 can drive
DCterminationsof250Ωormore,butlowercharacteristic
impedance traces can be driven with series termination or
AC termination topologies.
Hysteresis
The LT1720/LT1721 include internal hysteresis, which
makes them easier to use than many other comparable
speed comparators.
(a)
(b)
1720/21 F01
The input-output transfer characteristic is illustrated in
Figure 2 showing the definitions of VOS and VHYST based
upon the two measurable trip points. The hysteresis band
makestheLT1720/LT1721wellbehaved, evenwithslowly
moving inputs.
Figure 1. Typical Topside Metal for Multilayer PCB Layouts
Figure 1a shows a typical topside layout of the LT1720 on
such a multilayer board. Shown is the topside metal etch
including traces, pin escape vias, and the land pads for an
SO-8 LT1720 and its adjacent X7R 10nF bypass capacitor
in a 1206 case.
The ground trace from Pin 5 runs under the device up to
the bypass capacitor, shielding the inputs from the
outputs. Note the use of a common via for the LT1720 and
the bypass capacitor, which minimizes interference from
highfrequencyenergyrunningaroundthegroundplaneor
power distribution traces.
V
OH
V
HYST
+
–
(= V
– V
)
TRIP
TRIP
V
/2
HYST
Figure 1b shows a typical topside layout of the LT1721 on
a multilayer board. In this case, the power and ground
traces have been extended to the bottom of the device
solely to act as high frequency shields between input and
output traces.
V
OL
+
–
∆V = V – V
IN
IN
IN
0
–
+
V
V
TRIP
TRIP
+
–
V
+ V
2
TRIP
TRIP
V
=
OS
1720/21 F02
Although both VCC pins are electrically shorted internal to
the LT1721, they must be shorted together externally as
well in order for both to function as shields. The same is
true for the two GND pins.
Figure 2. Hysteresis I/O Characteristics
8
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
The exact amount of hysteresis will vary from part to part
asindicatedinthespecificationstable.Thehysteresislevel
will also vary slightly with changes in supply voltage and
common mode voltage. A key advantage of the LT1720/
LT1721 is the significant reduction in these effects, which
is important whenever an LT1720/LT1721 is used to de-
tect a threshold crossing in one direction only. In such a
case, the relevant trip point will be all that matters, and a
stable offset voltage with an unpredictable level of hyster-
esis, as seen in competing comparators, is of little value.
TheLT1720/LT1721aremanytimesbetterthanpriorcom-
parators in these regards. In fact, the CMRR and PSRR
tests are performed by checking for changes in either trip
point to the limits indicated in the specifications table.
Because the offset voltage is the average of the trip points,
the CMRR and PSRR of the offset voltage is therefore
guaranteed to be at least as good as those limits. This
more stringent test also puts a limit on the common mode
and power supply dependence of the hysteresis voltage.
voltage on the right side of R3 is 300mV or VCC – 300mV,
for a total voltage swing of (VCC – 300mV) – 300mV =
VCC – 600mV.
Withthisinmind, calculationoftheresistorvaluesneeded
isatwo-stepprocess.First,calculatethevalueofR3based
on the additional hysteresis desired, the output voltage
swing, and the impedance of the primary bias string:
R3 = (R1 R2)(VCC – 0.6V)/(additional hysteresis)
Additional hysteresis is the desired overall hysteresis less
the internal 3.5mV hysteresis.
The second step is to recalculate R2 to set the same
averagethresholdasbefore. Theaveragethresholdbefore
was set at VTH = (VREF)(R1)/(R1 + R2). The new R2 is
calculated based on the average output voltage (VCC/2)
and the simplified circuit model in Figure 4. To assure that
the comparator’s noninverting input is, on average, the
same VTH as before:
R2′ = (VREF – VTH)/(VTH/R1 + (VTH – VCC/2)/R3)
Additionalhysteresismaybeaddedexternally. Therail-to-
rail outputs of the LT1720/LT1721 make this more pre-
dictable than with TTL output comparators due to the
LT1720/LT1721’s small variability of VOH (output high
voltage).
For additional hysteresis of 10mV or less, it is not uncom-
mon for R2′ to be the same as R2 within 1% resistor
tolerances.
This method will work for additional hysteresis of up to a
few hundred millivolts. Beyond that, the impedance of R3
is low enough to effect the bias string, and adjustment of
R1 may also be required. Note that the currents through
the R1/R2 bias string should be many times the input
currents of the LT1720/LT1721. For 5% accuracy, the
current must be at least 120µA(6µA IB ÷ 0.05); more for
higher accuracy.
To add additional hysteresis, set up positive feedback by
adding additional external resistor R3 as shown in Figure
3. ResistorR3addsaportionoftheoutputtothethreshold
set by the resistor string. The LT1720/LT1721 pulls the
outputs to the supply rail and ground to within 200mV of
the rails with light loads, and to within 400mV with heavy
loads. For the load of most circuits, a good model for the
V
REF
R2′
V
REF
V
TH
R3
R3
V
2
CC
V
=
AVERAGE
R2
R1
+
+
1/2 LT1720
1/2 LT1720
R1
–
–
1720/21 F04
INPUT
1720/21 F03
Figure 3. Additional External Hysteresis
Figure 4. Model for Additional Hysteresis Calculations
9
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
Interfacing the LT1720/LT1721 to ECL
100µA of forward current. R4 prevents this with the
minimum additional power dissipation.
The LT1720/LT1721 comparators can be used in high
speed applications where Emitter-Coupled Logic (ECL) is
deployed. To interface the outputs of the LT1720/LT1721
to ECL logic inputs, standard TTL/CMOS to ECL level
translators such as the 10H124, 10H424 and 100124 can
be used. These components come at a cost of a few
nanosecondsadditionaldelayaswellassupplycurrentsof
50mA or more, and are only available in quads. A faster,
simpler and lower power translator can be constructed
with resistors as shown in Figure 5.
Finally, Figure 5d shows the case of driving standard,
negative-rail, ECL with the LT1720/LT1721. Resistor val-
ues are given for both ECL interface types and for both a
5V and 3V LT1720/LT1721 supply rail. Again, a fourth
resistor,R4isneededtopreventthelowstatecurrentfrom
flowing out of the LT1720/LT1721, turning on the internal
ESD/substrate diodes. Not only can the output stage func-
tionality and speed suffer, but in this case the substrate is
common to all the comparators in the LT1720/LT1721, so
operation of the other comparator(s) in the same package
could also be affected. Resistor R4 again prevents this
with the minimum additional power dissipation.
Figure 5a shows the standard TTL to Positive ECL (PECL)
resistive level translator. This translator cannot be used
for the LT1720/LT1721, or with CMOS logic, because it
depends on the 820Ω resistor to limit the output swing
(VOH)oftheall-NPNTTLgatewithitsso-calledtotem-pole
output. The LT1720/LT1721 are fabricated in a comple-
mentary bipolar process and their output stage has a PNP
driver that pulls the output nearly all the way to the supply
rail, even when sourcing 10mA.
For all the dividers shown, the output impedance is about
110Ω. This makes these fast, less than a nanosecond,
with most layouts. Avoid the temptation to use speedup
capacitors. Not only can they foul up the operation of the
ECL gate because of overshoots, they can damage the
ECL inputs, particularly during power-up of separate
supply configurations.
Figure 5b shows a three resistor level translator for inter-
facing the LT1720/LT1721 to ECL running off the same
supply rail. No pull-down on the output of the LT1720/
LT1721 is needed, but pull-down R3 limits the VIH seen by
the PECL gate. This is needed because ECL inputs have
both a minimum and maximum VIH specification for
proper operation. Resistor values are given for both ECL
interface types; in both cases it is assumed that the
LT1720/LT1721 operates from the same supply rail.
The level translator designs assume one gate load. Mul-
tiple gates can have significant IIH loading, and the trans-
missionlineroutingandterminationissuesalsomakethis
case difficult.
ECL,andparticularlyPECL,isvaluabletechnologyforhigh
speed system design, but it must be used with care. With
less than a volt of swing, the noise margins need to be
evaluated carefully. Note that there is some degradation of
noise margin due to the ±5% resistor selections shown.
With10KH/E,thereisnotemperaturecompensationofthe
logic levels, whereas the LT1720/LT1721 and the circuits
shown give levels that are stable with temperature. This
will degrade the noise margin over temperature. In some
configurations it is possible to add compensation with
diode or transistor junctions in series with the resistors of
these networks.
Figure 5c shows the case of translating to PECL from an
LT1720/LT1721 powered by a 3V supply rail. Again,
resistorvaluesaregivenforbothECLinterfacetypes.This
time four resistors are needed, although with 10KH/E, R3
is not needed. In that case, the circuit resembles the
standard TTL translator of Figure 5a, but the function of
the new resistor, R4, is much different. R4 loads the
LT1720/LT1721 output when high so that the current
flowing through R1 doesn’t forward bias the LT1720/
LT1721’s internal ESD clamp diode. Although this diode
can handle 20mA without damage, normal operation and
performance of the output stage can be impaired above
For more information on ECL design, refer to the ECLiPS
data book (DL140), the 10KH system design handbook
(HB205) and PECL design (AN1406), all from Motorola.
10
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
5V
5V
180Ω
270Ω
820Ω
DO NOT USE FOR LT1720/LT1721
LEVEL TRANSLATION. SEE TEXT
LSTTL
10KH/E
(a) STANDARD TTL TO PECL TRANSLATOR
V
CC
R2
R1
V
R1
10KH/E 5V OR 5.2V 510Ω 180Ω 750Ω
100K/E 4.5V 620Ω 180Ω 510Ω
R2
R3
CC
1/2 LT1720
R3
(b) LT1720/LT1721 OUTPUT TO PECL TRANSLATOR
V
CC
3V
R2
R1
R4
V
R1
R2
R3
R4
CC
1/2 LT1720
10KH/E 5V OR 5.2V 300Ω 180Ω OMIT 560Ω
100K/E
4.5V
330Ω 180Ω 1500Ω 1000Ω
R3
(c) 3V LT1720/LT1721 OUTPUT TO PECL TRANSLATOR
V
CC
R4
ECL FAMILY
V
V
R1
R2
R3
R4
EE
CC
R1
5V
3V
5V
3V
560Ω 270Ω 330Ω 1200Ω
270Ω 510Ω 300Ω 330Ω
680Ω 270Ω 300Ω 1500Ω
330Ω 390Ω 270Ω 430Ω
1720/21 F05
1/2 LT1720
10KH/E
–5.2V
–4.5V
R2
R3
100K/E
V
EE
(d) LT1720/LT1721 OUTPUT TO STANDARD ECL TRANSLATOR
Figure 5
11
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
Circuit Description
Technology’s rail-to-rail amplifiers and other products.
But the output of a comparator is digital, and this output
stagecandriveTTLorCMOSdirectly.ItcanalsodriveECL,
as described earlier, or analog loads as demonstrated in
the applications to follow.
TheblockdiagramofonecomparatorintheLT1720/LT1721
is shown in Figure 6. There are differential inputs
(+IN/–IN), an output (OUT), a single positive supply (VCC)
and ground (GND). All comparators are completely inde-
pendent, sharing only the power and ground pins. The
circuit topology consists of a differential input stage, a
gain stage with hysteresis and a complementary
common-emitter output stage. All of the internal signal
pathsutilizelowvoltageswingsforhighspeedatlowpower.
Thebiasconditionsandsignalswingsintheoutputstages
are designed to turn their respective output transistors off
faster than on. This nearly eliminates the surge of current
from VCC to ground that occurs at transitions, keeping the
power consumption low even with high output-toggle
frequencies.
The input stage topology maximizes the input dynamic
range available without requiring the power, complexity
and die area of two complete input stages such as are
foundinrail-to-railinputcomparators.Witha2.7Vsupply,
the LT1720/LT1721 still have a respectable 1.6V of input
common mode range. The differential input voltage range
is rail-to-rail, without the large input currents found in
competing devices. The input stage also features phase
reversal protection to prevent false outputs when the
inputs are driven below the –100mV common mode
voltage limit.
The low surge current is what keeps the power consump-
tion low at high output-toggle frequencies. The frequency
dependence of the supply current is shown in the Typical
Performance Characteristics. Just 20pF of capacitive load
on the output more than triples the frequency dependent
rise. Theslopeoftheno-loadcurveisjust32µA/MHz. With
a 5V supply, this current is the equivalent of charging and
discharging just 6.5pF. The slope of the 20pF load curve is
133µA/MHz, an addition of 101µA/MHz, or 20µA/MHz-V,
units that are equivalent to picoFarads.
Theinternalhysteresisisimplementedbypositive,nonlin-
ear feedback around a second gain stage. Until this point,
the signal path has been entirely differential. The signal
path is then split into two drive signals for the upper and
lower output transistors. The output transistors are con-
nected common emitter for rail-to-rail output operation.
The Schottky clamps limit the output voltages at about
300mVfromtherail, notquitethe50mVor15mVofLinear
The LT1720/LT1721 dynamic current can be estimated by
addingtheexternalcapacitiveloadingtoaninternalequiva-
lent capacitance of 5pF to 15pF, multiplied by the toggle
frequency and the supply voltage. Because the capaci-
tance of routing traces can easily approach these values,
the dynamic current is dominated by the load in most
circuits.
V
NONLINEAR STAGE
CC
+
–
+
Σ
+IN
+
–
+
–
A
A
OUT
V1
V2
+
Σ
–IN
+
–
GND
1720/21 F06
Figure 6. LT1720/LT1721 Block Diagram
12
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
Speed Limits
The second output speed limit is the clamp turnaround.
The LT1720/LT1721 output is optimized for fast initial
response, with some loss of turnaround speed, limiting
the toggle frequency. The output transistors are idled in a
low power state once VOH or VOL is reached by detecting
the Schottky clamp action. It is only when the output has
slewed from the old voltage to the new voltage, and the
clamp circuitry has settled, that the idle state is reached
andtheoutputisfullyreadytotransitionagain. Thisclamp
turnaround time is typically 8ns for each direction, result-
ing in a maximum toggle frequency of 62.5MHz, or a
125MB data rate. With higher frequencies, dropout and
runt pulses can occur. Increases in capacitive load will
increase the time needed for slewing due to the limited
slew currents and the maximum toggle frequency will
decrease further. For higher toggle frequency applica-
tions, consider the LT1394, whose linear output stage can
toggle at 100MHz typical.
The LT1720/LT1721 comparators are intended for high
speed applications, where it is important to understand a
few limitations. These limitations can roughly be divided
into three categories: input speed limits, output speed
limits, and internal speed limits.
There are no significant input speed limits except the
shunt capacitance of the input nodes. If the 2pF typical
input nodes are driven, the LT1720/LT1721 will respond.
The output speed is constrained by two mechanisms, the
firstofwhichistheslewcurrentsavailablefromtheoutput
transistors. To maintain low power quiescent operation,
the LT1720/LT1721 output transistors are sized to deliver
25mA to 45mA typical slew currents. This is sufficient to
drive small capacitive loads and logic gate inputs at
extremelyhighspeeds.Buttheslewratewillslowdramati-
callywithheavycapacitiveloads.Becausethepropagation
delay (tPD) definition ends at the time the output voltage is
halfway between the supplies, the fixed slew current
actually makes the LT1720/LT1721 faster at 3V than 5V
with 20mV of input overdrive.
The internal speed limits manifest themselves as disper-
sion. All comparators have some degree of dispersion,
defined as a change in propagation delay versus input
overdrive. The propagation delay of the LT1720/LT1721
will vary with overdrive, from a typical of 4.5ns at 20mV
overdrive to 7ns at 5mV overdrive (typical). The LT1720/
LT1721’s primary source of dispersion is the hysteresis
stage. As a change of polarity arrives at the gain stage, the
positive feedback of the hysteresis stage subtracts from
the overdrive available. Only when enough time has
elapsedforasignaltopropagateforwardthroughthegain
stage, backwards through the hysteresis stage and for-
ward through the gain stage again, will the output stage
receive the same level of overdrive that it would have
received in the absence of hysteresis.
Another manifestation of this output speed limit is skew,
the difference between tPD+ and tPD–. The slew currents of
theLT1720/LT1721varywiththeprocessvariationsofthe
PNP and NPN transistors, for rising edges and falling
edges respectively. The typical 0.5ns skew can have either
polarity, rising edge or falling edge faster. Again, the skew
will increase dramatically with heavy capacitive loads.
The skews of comparators in a single package are corre-
lated, but not identical. Besides some random variability,
there is a small (100ps to 200ps) systematic skew due to
physical parasitics of the packages. For the LT1720 SO-8,
comparatorA, whoseoutputisadjacenttotheVCC pin, will
have a relatively faster rising edge than comparator B.
Likewise, comparator B, by virtue of an output adjacent to
the ground pin will have a relatively faster falling edge.
Similar dependencies occur in the LT1721 S16, while the
systemic skews in the smaller MSOP and SSOP packages
arehalfagainassmall. Ofcourse, ifthecapacitiveloadson
the two comparators of a single package are not identical,
the differential timing will degrade further.
With5mVofoverdrive, theLT1720/LT1721arefasterwith
a 5V supply than with a 3V supply, the opposite of what is
true with 20mV overdrive. This is due to the internal speed
limit, because the gain stage is faster at 5V than 3V due
primarily to the reduced junction capacitances with higher
reverse voltage bias.
Inmanyapplications, asshowninthefollowingexamples,
there is plenty of input overdrive. Even in applications
providing low levels of overdrive, the LT1720/LT1721 are
13
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
fast enough that the absolute dispersion of 2.5ns
noninvertinginput.ThecircuitwilloperatewithanyAT-cut
crystal from 1MHz to 10MHz over a 2.7V to 6V supply
range. As the power is applied, the circuit remains off until
the LT1720/LT1721 bias circuits activate, at a typical VCC
of 2V to 2.2V (25°C), at which point the desired frequency
output is generated.
(= 7 – 4.5) is often small enough to ignore.
The gain and hysteresis stage of the LT1720/LT1721 is
simple, short and high speed to help prevent parasitic
oscillations while adding minimum dispersion. This in-
ternal “self-latch” can be usefully exploited in many
applicationsbecauseitoccursearlyinthesignalchain, in
a low power, fully differential stage. It is therefore highly
immune to disturbances from other parts of the circuit,
either in the same comparator, on the supply lines, or
from the other comparator(s) in the same package. Once
a high speed signal trips the hysteresis, the output will
respond, after a fixed propagation delay, without regard
to these external influences that can cause trouble in
nonhysteretic comparators.
The output duty cycle for this circuit is roughly 50%, but
it is affected by resistor tolerances and, to a lesser extent,
by comparator offsets and timings. If a 50% duty cycle is
required, the circuit of Figure 7 creates a pair of comple-
mentary outputs with a forced 50% duty cycle. Crystals
are narrow-band elements, so the feedback to the nonin-
vertinginputisafilteredanalogversionofthesquarewave
output.Changingthenoninvertingreferencelevelcanthere-
fore vary the duty cycle. C1 operates as in the previous
example, whereas C2 creates a complementary output by
comparing the same two nodes with the opposite input
polarity. A1 compares band-limited versions of the out-
puts and biases C1’s negative input. C1’s only degree of
freedom to respond is variation of pulse width; hence the
outputs are forced to 50% duty cycle. Again, the circuit
operatesfrom2.7Vto6V, andtheskewbetweentheedges
of the two outputs are shown in Figure 8. There is a slight
duty cycle dependence on comparator loading, so equal
capacitive and resistive loading should be used in critical
±VTRIP Test Circuit
The input trip points are tested using the circuit shown in
the Test Circuits section that precedes this Applications
Information section. The test circuit uses a 1kHz triangle
wave to repeatedly trip the comparator being tested. The
LT1720/LT1721outputisusedtotriggerswitchedcapaci-
tor sampling of the triangle wave, with a sampler for each
direction. Because the triangle wave is attenuated 1000:1
and fed to the LT1720/LT1721’s differential input, the
sampled voltages are therefore 1000 times the input trip
voltages. The hysteresis and offset are computed from the
trip points as shown.
V
CC
2.7V TO 6V
1MHz TO 10MHz
CRYSTAL (AT-CUT)
2k
220Ω
Crystal Oscillators
620Ω
GROUND
CASE
A simple crystal oscillator using one comparator of an
LT1720/LT1721 is shown on the first page of this data
sheet. The 2k-620Ω resistor pair set a bias point at the
comparator’s noninverting input. The 2k-1.8k-0.1µF path
sets the inverting input node at an appropriate DC average
level based on the output. The crystal’s path provides
resonant positive feedback and stable oscillation occurs.
Although the LT1720/LT1721 will give the correct logic
output when one input is outside the common mode
range, additional delays may occur when it is so operated,
opening the possibility of spurious operating modes.
Therefore, the DC bias voltages at the inputs are set near
the center of the LT1720/LT1721’s common mode range
and the 220Ω resistor attenuates the feedback to the
+
C1
OUTPUT
100k
1/2 LT1720
–
2k
+
–
A1
LT1636
0.1µF
0.1µF
1.8k
0.1µF
1k
100k
+
C2
OUTPUT
1/2 LT1720
–
1720 F07
Figure 7. Crystal Oscillator with Complementary
Outputs and 50% Duty Cycle
14
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
1000
56% low duty cycle, sufficient to allow 2ns between the
high pulses. Figure 10 shows the two outputs.
800
600
400
200
The optional A1 feedback network shown can be used to
force identical output duty cycles. The steady state duty
cycles of both outputs will be 44%. Note, though, that the
addition of this network only adjusts the percentage of
time each output is high to be the same, which can be
important in switching circuits requiring identical settling
times. Itcannotadjusttherelativephasesbetweenthetwo
outputs to be exactly 180° apart, because the signal at the
input node driven by the crystal is not a pure sinusoid.
0
2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
1720/21 F08
Q0
2V/DIV
Figure 8. Timing Skew of Figure 7’s Circuit
applications. This circuit works well because of the two
matcheddelaysandrail-to-railstyleoutputsoftheLT1720.
Q1
2V/DIV
ThecircuitinFigure9showsacrystaloscillatorcircuitthat
generatestwononoverlappingclocksbymakingfulluseof
the two independent comparators of the LT1720.
C1 oscillates as before, but with a lower reference level,
C2’s output will toggle at different times. The resistors set
thedegreeofseparationbetweentheoutput’shighpulses.
With the values shown, each output has a 44% high and
20ns/DIV
Figure 10. Nonoverlapping Outputs of Figure 9's Circuit
V
CC
2.7V TO 6V
10MHz
CRYSTAL (AT-CUT)
2k
220Ω
620Ω
GROUND
CASE
+
C1
OUTPUT 0
1/2 LT1720
–
OPTIONAL—
SEE TEXT
100k
2k
+
A1
LT1636
0.1µF
1.3k
0.1µF
–
0.1µF
1k
2.2k
100k
+
C2
OUTPUT 1
1/2 LT1720
1720/21 F09
–
Figure 9. Crystal-Based Nonoverlapping 10MHz Clock Generator
15
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
Timing Skews
high speed instrumentation. The circuit in Figure 12 is a
delay detector which will output a pulse when signals X
and Y are out of sync (specifically, when X is high and Y is
low). Note that the addition of an identical circuit to detect
the opposite situation (X low and Y high) allows for full
skew detection.
For a number of reasons, the LT1720/LT1721’s superior
timing specifications make them an excellent choice for
applications requiring accurate differential timing skew.
The comparators in a single package are inherently well
matched, with just 300ps ∆tPD typical. Monolithic con-
struction keeps the delays well matched vs supply voltage
and temperature. Crosstalk between the comparators,
usually a disadvantage in monolithic duals and quads, has
minimal effect on the LT1720/LT1721 timing due to the
internal hysteresis, as described in the Speed Limits
section.
Comparators U1A and U1B clean up the incoming signals
and render the circuit less sensitive to input levels and
slew rates. The resistive divider network provides level
shifting for the downstream comparator’s common mode
input range, as well as offset to keep the output low except
during a decisive event. When the upstream comparator’s
outputs can overcome the resistively generated offset
(and hysteresis), comparator U1C performs a Boolean
“X*_Y” function and produces an output pulse (see Fig-
ure 13). The circuit will give full output response with
input delays down to 3ns and partial output response with
inputdelaysdownto1.8ns.CapacitorC1helpsensurethat
an imbalance of parasitic capacitances in the layout will
not cause common mode excursions to result in differen-
tial mode signal and false outputs.1
The circuits of Figure 11 show basic building blocks for
differential timing skews. The 2.5k resistance interacts
with the 2pF typical input capacitance to create at least
±4ns delay, controlled by the potentiometer setting.
A differential and a single-ended version are shown. In the
differentialconfiguration,theoutputedgescanbesmoothly
scrolled through ∆t = 0 with negligible interaction.
3ns Delay Detector
1 Make sure the input levels at X and Y are not too close to the 0.5V threshold set by the R8–R9
divider. If you are still getting false outputs, try increasing C1 to 10pF or more. You can also look
fortheproblemintheimpedancebalance(R5||R6=R7)attheinputsofU1C. Increasingtheoffset
by lowering R5 will help reject false outputs, but R7 should also be lowered to maintain impedance
balance. For ease of design and parasitic matching, R7 can be replaced by two parallel resistors
equal to R5 and R6.
It is often necessary to measure comparative timing of
pulseedgesinordertodeterminethetruesynchronicityof
clock and control signals, whether in digital circuitry or in
LT1720
LT1720
C
IN
C
IN
+
–
+
INPUT
–
2.5k
C
IN
C
IN
0ns TO 4ns
SINGLE-ENDED
DELAY
DIFFERENTIAL ±4ns
RELATIVE SKEW
INPUT
2.5k
C
IN
C
IN
–
+
–
+
C
IN
C
IN
V
V
REF
REF
1720/21 F11
Figure 11. Building Blocks for Timing Skew Generation with the LT1720
16
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
DELAY DETECTOR
5V
R5
1.82k*
OPTIONAL LOGARITHMIC PULSE STRETCHER (SEE TEXT)
+
X
301Ω*
R6
301Ω*
U1A
5V
1/4 LT1721
51Ω*
CAPTURE
–
0.33µF
R1
–
1N5711
499Ω*
Z
U1C
R8*
4.53k
C1
5.6pF
301Ω*
+
1/4 LT1721
V
V
U1D
IN
C
R9
487Ω*
5V
0.1µF
L
+
1/4 LT1721
C2
540pF
**
–
5V
–
301Ω*
U1B
1/4 LT1721
475Ω*
Y
+
+
R7
261Ω*
51Ω*
R2
1k*
R3
1Ω*
–
V
OFF
1V
R4
DELAY
X
Y
Z
30Ω*
0V
1V
0V
1720/21 F12
* 1% METAL FILM RESISTOR
** 270pF ×2 FOR REDUCED LEAD INDUCTANCE
5V
0V
RESULT OF X AND NOT Y
Figure 12. 3ns Delay Detector with Logarithmic Pulse Stretcher
X
Y
Z
Figure 13. Output Pulse Due to Delay of Y Input Pulse
17
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
Optional Logarithmic Pulse Stretcher
For simplicity, with tP < τ1, and neglecting the very slight
delay in turn-on due to offset and hysteresis, the equation
can be approximated by:
The fourth comparator of the quad LT1721 can be put to
work as a logarithmic pulse stretcher. This simple circuit
can help tremendously if you don’t have a fast enough
oscilloscope(orcontrolcircuit)toeasilycapture3nspulse
widths (or faster). When an input pulse occurs, C2 is
charged up with a 180ns capture2 time constant. The
hysteresis and 10mV offset across R3 are overcome
within the first nanosecond3, switching the comparator
output high. When the input pulse subsides, C2 dis-
chargeswitha540nstimeconstant,keepingthecompara-
tor on until the decay overrides the 10mV offset across R3
minus hysteresis. Because of this exponential decay, the
output pulse width will be proportional to the logarithm of
theinputpulsewidth. Itisimportanttobypassthecircuit’s
VCC well to avoid coupling into the resistive divider. R4
keepsthequiescentinputvoltageinarangewhereforward
leakage of the diode due to the 0.4V VOL of the driving
comparator is not a problem.
tOUT = τ2 • ln [(VCH • tP/τ1)/(VOFF – VH/2)]
(2)
For example, an 8ns input pulse gives a 1.67µs output
pulse. Doubling the input pulse to 16ns lengthens the
output pulse by 0.37µs. Doubling the input pulse again to
32ns adds another 0.37µs to the output pulse, and so on.
The rate of 0.37µs per octave falls out of the above
equation as:
∆tOUT/octave = τ2 • ln(2)
(3)
There is ±0.01µs jitter5 in the output pulse which gives an
uncertainty referred to the input pulse of less than 2%
(60ps resolution on a 3ns pulse with a 60MHz oscillo-
scope—not bad!). The beauty of this circuit is that it gives
resolution precisely where it’s hardest to get. The jitter is
due to a combination of the slow decay of the last few
millivolts on C2 and the 4nV/√Hz noise and 400MHz
bandwidthoftheLT1721inputstage.Increasingtheoffset
across R3 or decreasing τ2 will decrease this jitter at the
expense of dynamic range.
Neglectingsomeeffects4, theoutputpulseisrelatedtothe
input pulse as:
tOUT = τ2 • ln {VCH • [1 – exp (–tP/τ1)]/(VOFF – VH/2)}
– τ1 • ln [VCH/(VCH – VOFF – VH/2)]
The circuit topology itself is extremely fast, limited theo-
retically only by the speed of the diode, the capture time
constant τ1 and the pulse source impedance. Figure 14
shows results achieved with the implementation shown,
compared to a plot of equation (1). The low end is limited
by the delivery time of the upstream comparators. As the
input pulse width is increased, the log function is con-
strained by the asymptotic RC response but, rather than
becoming clamped, becomes time linear. Thus, for very
long input pulses the third term of equation (1) dominates
and the circuit becomes a 3µs pulse stretcher.
+ tP
(1)
where
tP = input pulse width
tOUT = output pulse width
τ1 = R1 || R2 • C2
τ2 = R2 • C2
the capture time constant
the decay time constant
the voltage drop across R1
LT1721 hysteresis
VOFF = 10mV
2 So called because the very fast input pulse is “captured,” for later examination, as a charge on the
capacitor.
VH = 3.5mV
3 Assumingtheinputpulseslewrateatthediodeisinfinite.Thiseffectivedelayconstant,about0.4%
of τ1 or 0.8ns, is the second term of equation 1, below. Driven by the 2.5ns slew-limited LT1721,
this effective delay will be 2ns.
4 VC is dependent on the LT1721 output voltage and nonlinear diode characteristics. Also, the
Thevenin equivalent charge voltage seen by C2 is boosted slightly by R2 being terminated above
ground.
5 Output jitter increases with inputs pulse widths below ~3ns.
VC = VIN – VFDIODE
the input pulse voltage after
the diode drop
VCH = VC • R2/(R1 + R2) the effective source voltage
for the charge
18
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
14
easily measured 1.70µs output pulses. A 12 foot cable
length difference will result in ~18.4ns delay and 2.07µs
output pulses. The difference in the two output pulse
widths is the per-octave response of your circuit (see
equation (3)). Shorter cable length differences can be
used to get a plot of circuit performance down to 1.5ns (if
any), which can then later be used as a lookup reference
whenyouhavemovedfromquantifyingthecircuittousing
the circuit. (Note there is a slight aberration in perfor-
mance below 10ns. See Figure 14.) As a final check, feed
the circuit with identical cable lengths and check that it is
not producing any output pulses.
12
10
8
6
MEASURED
4
EQUATION 1
2
0
1
10
100
(ns)
1000
10000
t
PULSE
1720/21 F14
Figure 14. Log Pulse Stretcher Output Pulse vs Input Pulse
10ns Triple Overlap Generator
The circuit of Figure 16 utilizes an LT1721 to generate
three overlapping outputs whose pulse edges are sepa-
ratedby10nsasshown. ThetimeconstantissetbytheRC
network on the output of comparator A. Comparator B and
Dtripatfixedpercentagesoftheexponentialvoltagedecay
across the capacitor. The 4.22kΩ feed-forward to the C
comparator’s inverting input keeps the delay differences
the same in each direction despite the exponential nature
of the RC network’s voltage.
NANOSECOND
INPUT RANGE
MICROSECOND
OUTPUT RANGE
X
Y
1 FOOT CABLE
L
t
OUT
(SEE TEXT)
CIRCUIT OF
FIGURE 12
2V
0V
There is a 15ns delay to the first edge in both directions,
due to the 4.5ns delay of two LT1721 comparators, plus
6ns delay in the RC network. This starting delay is short-
ened somewhat if the pulse was shorter than 40ns be-
cause the RC network will not have fully settled; however,
the 10ns edge separations stay constant.
SPLITTER
n FOOT CABLE
1720/21 F15
Thevaluesshownutilizeonlythelowest75%ofthesupply
voltagespan, whichallowsittoworkdownto2.7Vsupply.
Thedelaydifferencesgrowacouplenanosecondsfrom5V
to 2.7V supply due to the fixed VOL/VOH drops which grow
as a percentage at low supply voltage. To keep this effect
to a minimum, the 1kΩ pull-up on comparator A provides
equal loading in either state.
Figure 15. RG-58 Cable with Velocity of Propogation = 66%;
Delay at Y = (n – 1) • 1.54ns
You don’t need expensive equipment to confirm the actual
overall performance of this circuit. All you need is a
respectablewaveformgenerator(capableof>~100kHz), a
splitter, a variety of cable lengths and a 20MHz or 60MHz
oscilloscope. Split a single pulse source into different
cable lengths and then into the delay detector, feeding the
longer cable into the Y input (see Figure 15). A 6 foot cable
length difference will create a ~9.2ns delay (using 66%
propagation speed RG-58 cable), and should result in
Fast Waveform Sampler
Figure 17 uses a diode-bridge-type switch for clean, fast
waveform sampling. The diode bridge, because of its
inherent symmetry, provides lower AC errors than other
semiconductor-based switching technologies. This cir-
cuit features 20dB of gain, 10MHz full power bandwidth
19
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
V
CC
V
CC
OUTPUTS
+
U1B
1k
1/4 LT1721
V
CC
10ns
10ns
–
V
CC
INPUT
750Ω
909Ω
+
1.37k
215Ω
681Ω
U1A
+
1/4 LT1721
U1C
100pF
V
–
REF
1/4 LT1721
10ns
10ns
–
681Ω
4.22k
+
U1D
1/4 LT1721
–
453Ω
1720/21 F16
Figure 16. 10ns Triple Overlap Generator
5V
2.2k
2.2k
INPUT
±100mV FULL SCALE
+
–
OUTPUT
±1V FULL SCALE
LT1227
1k
909Ω
= 1N5711
AC BALANCE
3pF
= CA3039 DIODE ARRAY
(SUBSTRATE TO –5V)
100Ω
5V
1.5k
3.6k
1.1k
1.1k
0.1µF
1.1k
+
C
IN
1/2 LT1720
1.1k
–
MRF501
MRF501
SKEW
COMP
2k
10pF
SAMPLE
COMMAND
DC BALANCE
2.5k
+
500Ω
680Ω
11
8
1/2 LT1720
2k
–
820Ω
820Ω
6
9
C
IN
LM3045
13
10
51Ω
7
51Ω
1720/21 F17
–5V
Figure 17. Fast Waveform Sampler Using the LT1720 for Timing-Skew Compensation
20
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
and 100µV/°C baseline uncertainty. Switching delay is
less than 15ns and the minimum sampling window width
for full power response is 30ns.
is adjusted for minimal bridge ON vs OFF variation at the
output. The skew compensation and AC balance adjust-
ments are then optimized for minimum AC disturbance in
the output. Finally, unground the input and the circuit is
ready for use.
The input waveform is presented to the diode bridge
switch, the output of which feeds the LT1227 wideband
amplifier.TheLT1720comparators,triggeredbythesample
command, generate phase-opposed outputs. These sig-
nals are level shifted by the transistors, providing comple-
mentary bipolar drive to switch the bridge. A skew
compensation trim ensures bridge-drive signal simulta-
neity within 1ns. The AC balance corrects for parasitic
capacitive bridge imbalances. A DC balance adjustment
trims bridge offset.
Voltage-Controlled Clock Skew Generator
It is sometimes necessary to generate pairs of identical
clock signals that are phase skewed in time. Further, it is
desirable to be able to set the amount of time skew via a
tuning voltage. Figure 18’s circuit does this by utilizing
theLT1720todigitizephaseinformationfromavaractor-
tuned time domain bridge. A 0V to 2V control signal
provides ≈±10ns of output skew. This circuit operates
from a 2.7V to 6V supply.
The trim sequence involves grounding the input via 50Ω
and applying a 100kHz sample command. The DC balance
CLOCK
INPUT
V
CC
2.7V TO 6V
+
C1
FIXED
OUTPUT
Q
1/2 LT1720
–
V
CC
2k
2.5k
2.5k
2.5k*
10ns
TRIM
14k
2k*
“FIXED”
“SKEWED”
†
+
†
C2
SKEWED
OUTPUT
36pF
Q′
1/2 LT1720
12pF
–
MV-209
VARACTOR
DIODE
1M
1M
0.1µF
0.005µF
47µF
INPUT
L1**
0V TO 2V ≈
±10ns
+
–
V
CC
A1
LT1077
+
SKEW
1.1M
100k
2.2µF
V
SW
IN
= 1N4148
= 74HC04
6.2M*
LT1317 FB
GND
V
C
200pF
* 1% FILM RESISTOR
** SUMIDA CD43-100
1.82M*
†
POLYSTYRENE, 5%
1720/21 F18
Figure 18. Voltage-Controlled Clock Skew
21
LT1720/LT1721
U
W U U
APPLICATIONS INFORMATION
Coincidence Detector
AND gate could instead be used, but would add consider-
ably more delay than the 300ps contributed by this dis-
crete stage.
High speed comparators are especially suited for interfac-
ing pulse-output transducers, such as particle detectors,
to logic circuitry. The matched delays of a monolithic dual
are well suited for those cases where the coincidence of
two pulses needs to be detected. The circuit of Figure 19
isacoincidencedetectorthatusesanLT1720anddiscrete
components as a fast AND gate.
This circuit can detect coincident pulses as narrow as 3ns.
For narrower pulses, the output will degrade gracefully,
responding, but with narrow pulses that don’t rise all the
way to “high” before starting to fall. The decision delay is
4.5ns with input signals 50mV or more above the refer-
encelevel.ThiscircuitcreatesaTTLcompatibleoutputbut
it can typically drive CMOS as well.
Thereferencelevelissetto1V,anarbitrarythreshold.Only
when both input signals exceed this will a coincidence be
detected. The Schottky diodes from the comparator out-
puts to the base of the MRF-501 form the AND gate, while
the other two Schottkys provide for fast turn-off. A logic
For a more detailed description of the operation of this
circuit, see Application Note 75, pages 10 and 11.
5V
5V
GROUND
CASE LEAD
300Ω
+
MRF501
OUTPUT
1/2 LT1720
51Ω
5V
3.9k
–
1k
0.1µF
–
1/2 LT1720
+
300Ω
4× 1N5711
51Ω
1720/21 F19
300ps AND GATE
COINCIDENCE COMPARATORS
Figure 19. A 3ns Coincidence Detector
22
LT1720/LT1721
W
W
SI PLIFIED SCHE ATIC
23
LT1720/LT1721
U
PACKAGE DESCRIPTION Dimensions in inches (millimeters) unless otherwise noted.
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
7
5
8
6
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
1
3
4
2
0.010 – 0.020
(0.254 – 0.508)
× 45°
0.053 – 0.069
(1.346 – 1.752)
0.004 – 0.010
(0.101 – 0.254)
0.008 – 0.010
(0.203 – 0.254)
0°– 8° TYP
0.016 – 0.050
(0.406 – 1.270)
0.050
(1.270)
BSC
0.014 – 0.019
(0.355 – 0.483)
TYP
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
SO8 1298
24
LT1720/LT1721
U
PACKAGE DESCRIPTION Dimensions in inches (millimeters) unless otherwise noted.
MS8 Package
8-Lead Plastic MSOP
(LTC DWG # 05-08-1660)
0.118 ± 0.004*
(3.00 ± 0.102)
8
7
6
5
0.118 ± 0.004**
(3.00 ± 0.102)
0.193 ± 0.006
(4.90 ± 0.15)
1
2
3
4
0.040 ± 0.006
(1.02 ± 0.15)
0.034 ± 0.004
(0.86 ± 0.102)
0.007
(0.18)
0° – 6° TYP
SEATING
PLANE
0.012
(0.30)
REF
0.021 ± 0.006
(0.53 ± 0.015)
0.006 ± 0.004
(0.15 ± 0.102)
0.0256
(0.65)
BSC
MSOP (MS8) 1098
* DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
25
LT1720/LT1721
U
PACKAGE DESCRIPTION Dimensions in inches (millimeters) unless otherwise noted.
S Package
16-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.386 – 0.394*
(9.804 – 10.008)
16
15
14
13
12
11
10
9
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
5
7
8
1
2
3
4
6
0.010 – 0.020
(0.254 – 0.508)
× 45°
0.053 – 0.069
(1.346 – 1.752)
0.004 – 0.010
(0.101 – 0.254)
0.008 – 0.010
(0.203 – 0.254)
0° – 8° TYP
0.050
(1.270)
BSC
0.014 – 0.019
(0.355 – 0.483)
TYP
0.016 – 0.050
(0.406 – 1.270)
S16 1098
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
26
LT1720/LT1721
U
PACKAGE DESCRIPTION Dimensions in inches (millimeters) unless otherwise noted.
GN Package
16-Lead Plastic SSOP (Narrow 0.150)
(LTC DWG # 05-08-1641)
0.189 – 0.196*
(4.801 – 4.978)
0.009
(0.229)
REF
16 15 14 13 12 11 10 9
0.229 – 0.244
(5.817 – 6.198)
0.150 – 0.157**
(3.810 – 3.988)
1
2
3
4
5
6
7
8
0.015 ± 0.004
(0.38 ± 0.10)
× 45°
0.053 – 0.068
(1.351 – 1.727)
0.004 – 0.0098
(0.102 – 0.249)
0.007 – 0.0098
(0.178 – 0.249)
0° – 8° TYP
0.016 – 0.050
(0.406 – 1.270)
0.0250
(0.635)
BSC
0.008 – 0.012
(0.203 – 0.305)
* DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
GN16 (SSOP) 1098
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.
27
LT1720/LT1721
U
TYPICAL APPLICATION
Pulse Stretcher
capacitor C now begins charging through R and, at the
end of 100ns, C2 resets low. The output of C1 also goes
low, latching both outputs low. A new pulse at the input
of C1 can now restart the process. Timing capacitor C can
be increased without limit for longer output pulses.
For detecting short pulses from a single sensor, a pulse
stretcher is often required. The circuit of Figure 20 acts as
a one-shot, stretching the width of an incoming pulse to a
consistent 100ns. Unlike a logic one-shot, this LT1720-
based circuit requires only 100pV-s of stimulus to trigger.
This circuit has an ultimate sensitivity of better than 14mV
with 5ns to 10ns input pulses. It can even detect an
avalanche generated test pulse of just 1ns duration with
sensitivity better than 100mV.6 It can detect short events
better than the coincidence detector of Figure 14 because
the one-shot is configured to catch just 100mV of upward
movement from C1’s VOL, whereas the coincidence
detector’s 3ns specification is based on a full, legitimate
logic high, without the help of a regenerative one-shot.
The circuit works as follows: Comparator C1 functions as
a threshold detector, whereas comparator C2 is config-
uredasaone-shot. Thefirstcomparatorisprebiasedwith
a threshold of 8mV to overcome comparator and system
offsets and establish a low output in the absence of an
input signal. An input pulse sends the output of C1 high,
which in turn latches C2’s output high. The output of C2
is fed back to the input of the first comparator, causing
regeneration and latching both outputs high. Timing
6 See Linear Technology Application Note 47, Appendix B. This circuit can detect the output of the
pulse generator described after 40dB attenuation.
5V
0.01µF
15k
OUTPUT
–
C1
PULSE SOURCE
1/2 LT1720
50Ω
100ns
+
51Ω
24Ω
R
1k
6.8k
1N5711
C
100pF
–
C2
1/2 LT1720
+
2k
2k
1720/21 F20
2k
Figure 20. A 1ns Pulse Stretcher
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1016
UltraFast Precision Comparator
Industry Standard 10ns Comparator
Single Supply Version of LT1016
6mA Single Supply Comparator
450µA Single Supply Comparator
Single Comparator Similar to the LT1720/LT1721
LT1116
12ns Single Supply Ground-Sensing Comparator
7ns, UltraFast, Single Supply Comparator
60ns, Low Power, Single Supply Comparator
4.5ns Single Supply 3V/5V Comparator
LT1394
LT1671
LT1719
17201f LT/TP 1099 4K • PRINTED IN USA
28 LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
●
●
LINEAR TECHNOLOGY CORPORATION 1998
(408)432-1900 FAX:(408)434-0507 www.linear-tech.com
相关型号:
LT1721IS#TRPBF
LT1721 - Quad, 4.5ns, Single Supply 3V/5V Comparators with Rail-to-Rail Outputs; Package: SO; Pins: 16; Temperature Range: -40°C to 85°C
Linear
LT1722CS5#PBF
LT1722 - Single 200MHz Low Noise Precision Op Amps; Package: SOT; Pins: 5; Temperature Range: 0°C to 70°C
Linear
LT1722CS5#TRM
LT1722 - Single 200MHz Low Noise Precision Op Amps; Package: SOT; Pins: 5; Temperature Range: 0°C to 70°C
Linear
LT1722CS5#TRMPBF
LT1722 - Single 200MHz Low Noise Precision Op Amps; Package: SOT; Pins: 5; Temperature Range: 0°C to 70°C
Linear
LT1722CS5#TRPBF
LT1722 - Single 200MHz Low Noise Precision Op Amps; Package: SOT; Pins: 5; Temperature Range: 0°C to 70°C
Linear
LT1722CS8#PBF
LT1722 - Single 200MHz Low Noise Precision Op Amps; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LT1722CS8#TRPBF
LT1722 - Single 200MHz Low Noise Precision Op Amps; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
©2020 ICPDF网 联系我们和版权申明