LT3013EFE#TR [Linear]
LT3013 - 250mA, 4V to 80V Low Dropout Micropower Linear Regulator with PWRGD; Package: TSSOP; Pins: 16; Temperature Range: -40°C to 85°C;型号: | LT3013EFE#TR |
厂家: | Linear |
描述: | LT3013 - 250mA, 4V to 80V Low Dropout Micropower Linear Regulator with PWRGD; Package: TSSOP; Pins: 16; Temperature Range: -40°C to 85°C 光电二极管 输出元件 调节器 |
文件: | 总20页 (文件大小:217K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LT3013
250mA, 4V to 80V
Low Dropout Micropower
Linear Regulator with PWRGD
DESCRIPTION
FEATURES
The LT®3013 is a high voltage, micropower low dropout
linearregulator. Thedeviceiscapableofsupplying250mA
ofoutputcurrentwithadropoutvoltageof400mV.Designed
foruseinbattery-poweredorhighvoltagesystems,thelow
quiescent current (65μA operating and 1μA in shutdown)
makes the LT3013 an ideal choice. Quiescent current is
also well controlled in dropout.
n
Wide Input Voltage Range: 4V to 80V
n
Low Quiescent Current: 65μA
n
Low Dropout Voltage: 400mV
n
Output Current: 250mA
n
No Protection Diodes Needed
n
Adjustable Output from 1.24V to 60V
n
1μA Quiescent Current in Shutdown
n
Stable with 3.3μF Output Capacitor
Other features of the LT3013 include a PWRGD flag to
indicate output regulation. The delay between regulated
output level and flag indication is programmable with
a single capacitor. The LT3013 also has the ability to
operate with very small output capacitors. The regulator
is stable with only 3.3μF on the output while most older
devices require between 10μF and 100μF for stability.
Small ceramic capacitors can be used without any need
for series resistance (ESR) as is common with other
regulators. Internal protection circuitry includes reverse-
battery protection, current limiting, thermal limiting and
reverse current protection.
n
Stable with Aluminum, Tantalum or Ceramic
Capacitors
Reverse-Battery Protection
n
n
No Reverse Current Flow from Output to Input
n
Thermal Limiting
n
Thermally Enhanced 16-Lead TSSOP and
12-Pin (4mm × 3mm) DFN Package
APPLICATIONS
n
Low Current High Voltage Regulators
n
Regulator for Battery-Powered Systems
The device is available with an adjustable output with a
1.24Vreferencevoltage. TheLT3013regulator isavailable
in the thermally enhanced 16-lead TSSOP and the low
profile (0.75mm), 12-pin (4mm × 3mm) DFN package,
both providing excellent thermal characteristics.
n
Telecom Applications
Automotive Applications
n
, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
Dropout Voltage
TYPICAL APPLICATION
400
350
300
250
200
150
100
50
5V Supply with Shutdown
V
OUT
IN
OUT
ADJ
5V
250mA
V
LT3013
IN
750k
249k
5.4V TO
80V
1.6M
3.3μF
1μF
SHDN
PWRGD
GND
C
T
3013 TA01
V
SHDN
OUTPUT
1000pF
<0.3V
>2.0V
OFF
ON
0
0
50
100
150
200
250
OUTPUT CURRENT (mA)
3013 TA02
3013fe
1
LT3013
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Storage Temperature Range
IN Pin Voltage ......................................................... 80V
OUT Pin Voltage...................................................... 60V
IN to OUT Differential Voltage ................................. 80V
ADJ Pin Voltage ....................................................... 7V
SHDN Pin Input Voltage.......................................... 80V
CT Pin Voltage .................................................7V, –0.5V
PWRGD Pin Voltage.......................................80V, –0.5V
Output Short-Circuit Duration .......................... Indefinite
TSSOP Package.................................–65°C to 150°C
DFN Package......................................–65°C to 125°C
Operating Junction Temperature Range
(Notes 3, 10, 11)
LT3013E.............................................–40°C to 125°C
LT3013HFE.........................................–40°C to 140°C
LT3013MP..........................................–55°C to 125°C
Lead Temperature (FE16 Soldering, 10 sec) ......... 300°C
PIN CONFIGURATION
TOP VIEW
TOP VIEW
GND
NC
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
GND
NC
NC
OUT
1
2
3
4
5
6
12 NC
11 IN
10 IN
OUT
IN
OUT
IN
OUT
17
13
ADJ
NC
ADJ
9
8
7
NC
GND
SHDN
GND
SHDN
PWRGD
GND
C
T
PWRGD
C
T
GND
DE PACKAGE
FE PACKAGE
12-LEAD (4mm s 3mm) PLASTIC DFN
16-LEAD PLASTIC TSSOP
T
= 125°C, θ = 40°C/W, θ = 16°C/W
JA JC
EXPOSED PAD (PIN 13) IS GND
MUST BE SOLDERED TO PCB
JMAX
T
JMAX
= 140°C, θ = 40°C/W, θ = 16°C/W
JA JC
EXPOSED PAD (PIN 17) IS GND
MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
LT3013EDE#PBF
LT3013EFE#PBF
LT3013HFE#PBF
LT3013MPFE#PBF
LEAD BASED FINISH
LT3013EDE
TAPE AND REEL
LT3013EDE#TRPBF
LT3013EFE#TRPBF
LT3013HFE#TRPBF
LT3013MPFE#TRPBF
TAPE AND REEL
LT3013EDE#TR
PART MARKING
3013
PACKAGE DESCRIPTION
12-Lead (4mm x 3mm) Plastic DFN
16-Lead Plastic TSSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 140°C
–55°C to 125°C
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 140°C
–55°C to 125°C
3013EFE
3013HFE
16-Lead Plastic TSSOP
3013MPFE
PART MARKING
3013
16-Lead Plastic TSSOP
PACKAGE DESCRIPTION
12-Lead (4mm x 3mm) Plastic DFN
16-Lead Plastic TSSOP
LT3013EFE
LT3013EFE#TR
3013EFE
LT3013HFE
LT3013HFE#TR
3013HFE
16-Lead Plastic TSSOP
LT3013MPFE
LT3013MPFE#TR
3013MPFE
16-Lead Plastic TSSOP
Consult LTC Marketing for parts specified with wider operating temperature ranges.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
3013fe
2
LT3013
(LT3013E, LT3013MP)
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TJ = 25°C.
PARAMETER
CONDITIONS
= 250mA
MIN
TYP
MAX
UNITS
l
Minimum Input Voltage
ADJ Pin Voltage (Notes 2,3)
I
4
4.75
V
LOAD
V
= 4V, I
= 1mA
1.225
1.2
1.24
1.24
1.255
1.28
V
V
IN
LOAD
l
l
4.75V < V < 80V, 1mA < I
< 250mA
IN
LOAD
Line Regulation
ΔV = 4V to 80V, I
IN
= 1mA (Note 2)
0.1
7
5
mV
LOAD
Load Regulation (Note 2)
12
25
mV
mV
V
IN
V
IN
= 4.75V, ΔI
= 4.75V, ΔI
= 1mA to 250mA
= 1mA to 250mA
LOAD
LOAD
l
l
l
Dropout Voltage
I
I
= 10mA
= 10mA
160
250
400
230
300
mV
mV
LOAD
LOAD
V
= V
(Notes 4, 5)
OUT(NOMINAL)
IN
I
I
= 50mA
= 50mA
340
420
mV
mV
LOAD
LOAD
I
I
= 250mA
= 250mA
490
620
mV
mV
LOAD
LOAD
l
l
GND Pin Current
I
I
I
= 0mA
= 100mA
= 250mA
65
3
10
120
μA
mA
mA
LOAD
LOAD
LOAD
V
= 4.75V
IN
l
(Notes 4, 6)
18
Output Voltage Noise
ADJ Pin Bias Current
Shutdown Threshold
C
= 10μF, I
= 250mA, BW = 10Hz to 100kHz
100
30
μV
RMS
OUT
LOAD
(Note 7 )
100
2
nA
l
l
V
OUT
V
OUT
= Off to On
= On to Off
1.3
0.8
V
V
0.3
85
SHDN Pin Current (Note 8)
V
SHDN
V
SHDN
= 0V
= 6V
0.3
0.1
2
1
μA
μA
Quiescent Current in Shutdown
PWRGD Trip Point
V
IN
= 6V, V
= 0V
1
5
μA
SHDN
l
l
% of Nominal Output Voltage, Output Rising
% of Nominal Output Voltage
90
94
%
%
PWRGD Trip Point Hysteresis
PWRGD Output Low Voltage
1.1
140
3.0
1.6
75
I
= 50μA
250
6
mV
μA
V
PWRGD
C Pin Charging Current
T
C Pin Voltage Differential
T
V – V
CT(PWRGD High) CT(PWRGD Low)
Ripple Rejection
Current Limit
V
IN
= 7V(Avg), V
= 0.5V , f
= 120Hz, I = 250mA
LOAD
65
dB
mA
mA
μA
RIPPLE
P-P RIPPLE
V
IN
V
IN
= 7V, V
= 0V
400
OUT
l
= 4.75V, ΔV
= –0.1V (Note 2)
250
OUT
Reverse Output Current (Note 9)
V
OUT
= 1.24V, V < 1.24V (Note 2)
12
25
IN
(LT3013H)
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the –40°C to 140°C operating temperature range, otherwise specifications are at TJ = 25°C.
PARAMETER
CONDITIONS
= 200mA
MIN
TYP
MAX
UNITS
l
Minimum Input Voltage
ADJ Pin Voltage (Notes 2,3)
I
4
4.75
V
LOAD
V
= 4V, I
= 1mA
1.225
1.2
1.24
1.24
1.255
1.28
V
V
IN
LOAD
l
l
4.75V < V < 80V, 1mA < I
< 200mA
IN
LOAD
Line Regulation
ΔV = 4V to 80V, I
IN
= 1mA (Note 2)
0.1
6
5
mV
LOAD
Load Regulation (Note 2)
V
IN
V
IN
= 4.75V, ΔI
= 4.75V, ΔI
= 1mA to 200mA
= 1mA to 200mA
12
30
mV
mV
LOAD
LOAD
l
3013fe
3
LT3013
(LT3013H)
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the –40°C to 140°C operating temperature range, otherwise specifications are at TJ = 25°C.
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Dropout Voltage
IN
I
I
= 10mA
= 10mA
160
230
320
mV
mV
LOAD
LOAD
l
l
V
= V
(Notes 4, 5)
OUT(NOMINAL)
I
I
= 50mA
= 50mA
250
360
340
450
mV
mV
LOAD
LOAD
I
I
= 200mA
= 200mA
490
630
mV
mV
LOAD
LOAD
l
l
GND Pin Current
I
I
I
= 0mA
= 100mA
= 200mA
65
3
7
130
μA
mA
mA
LOAD
LOAD
LOAD
V
= 4.75V
IN
l
(Notes 4, 6)
18
Output Voltage Noise
ADJ Pin Bias Current
Shutdown Threshold
C
= 10μF, I
= 200mA, BW = 10Hz to 100kHz
100
30
μV
RMS
OUT
LOAD
(Note 7)
100
2
nA
l
l
V
OUT
V
OUT
= Off to On
= On to Off
1.3
0.8
V
V
0.3
85
SHDN Pin Current (Note 8)
V
SHDN
V
SHDN
= 0V
= 6V
0.3
0.1
2
1
μA
μA
Quiescent Current in Shutdown
PWRGD Trip Point
V
IN
= 6V, V
= 0V
1
5
μA
%
SHDN
l
l
% of Nominal Output Voltage, Output Rising
% of Nominal Output Voltage
90
95
PWRGD Trip Point Hysteresis
PWRGD Output Low Voltage
1.1
140
3.0
1.6
75
%
I
= 50μA
250
6
mV
μA
V
PWRGD
C Pin Charging Current
T
C Pin Voltage Differential
T
V – V
CT(PWRGD High) CT(PWRGD Low)
Ripple Rejection
Current Limit
V
IN
= 7V(Avg), V
= 0.5V , f
= 120Hz, I = 200mA
LOAD
65
dB
RIPPLE
P-P RIPPLE
V
IN
V
IN
= 7V, V
= 0V
400
mA
mA
OUT
l
= 4.75V, ΔV
= –0.1V (Note 2)
200
OUT
Reverse Output Current (Note 9)
V
OUT
= 1.24V, V < 1.24V (Note 2)
12
25
μA
IN
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3013 is tested and specified for these conditions with the
ADJ pin connected to the OUT pin.
Note 3: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specification will not apply
for all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 4: To satisfy requirements for minimum input voltage, the LT3013 is
tested and specified for these conditions with an external resistor divider
(249k bottom, 649k top) for an output voltage of 4.5V. The external
resistor divider will add a 5μA DC load on the output.
Note 7: ADJ pin bias current flows into the ADJ pin.
Note 8: SHDN pin current flows out of the SHDN pin.
Note 9: Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the rated output voltage. This current flows into the OUT
pin and out the GND pin.
Note 10: The LT3013E is guaranteed to meet performance specifications
from 0°C to 125°C operating junction temperature. Specifications over
the –40°C to 125°C operating junction temperature range are assured by
design, characterization and correlation with statistical process controls.
The LT3013H is tested to the LT3013H Electrical Characteristics table at
140°C operating junction temperature. High junction temperatures degrade
operating lifetimes. Operating lifetime is derated at junction temperatures
greater than 125°C. The LT3013MP is 100% tested and guaranteed over
the –55°C to 125°C operating junction temperature range.
Note 11: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C (LT3013E, LT3013MP) or 140°C (LT3013H)
when overtemperature protection is active. Continuous operation above
the specified maximum operating junction temperature may impair device
reliability.
Note 5: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specified output current. In dropout, the
output voltage will be equal to (V – V
).
IN
DROPOUT
Note 6: GND pin current is tested with V = 4.75V and a current source
IN
load. This means the device is tested while operating close to its dropout
region. This is the worst-case GND pin current. The GND pin current will
decrease slightly at higher input voltages.
3013fe
4
LT3013
TYPICAL PERFORMANCE CHARACTERISTICS
Typical Dropout Voltage
Guaranteed Dropout Voltage
Dropout Voltage
600
500
400
300
200
100
0
600
500
600
500
400
300
200
100
0
= TEST POINTS
T
≤ 125°C
J
T
= 125°C
J
I
= 250mA
L
I
= 100mA
L
400
300
T
≤ 25°C
J
T
= 25°C
J
I
= 50mA
L
I
= 10mA
= 1mA
L
200
100
0
I
L
0
50
100
150
200
250
0
50
100
150
200
250
–50
0
25 50 75 100 125 150
TEMPERATURE (°C)
–25
OUTPUT CURRENT (mA)
OUTPUT CURRENT (mA)
3013 G02
3013 G03
3013 G01
Quiescent Current
ADJ Pin Voltage
120
100
80
60
40
20
0
1.260
V
= 6V
= ∞
I
L
= 1mA
IN
L
= 0
R
I
1.255
1.250
L
V
= V
IN
SHDN
1.245
1.240
1.235
1.230
1.225
V
= GND
SHDN
1.220
–50
–25
0
25 50 75 100 125 150
TEMPERATURE (°C)
3013 G05
–50
0
25 50 75 100 125 150
TEMPERATURE (°C)
3013 G04
–25
3013fe
5
LT3013
TYPICAL PERFORMANCE CHARACTERISTICS
Quiescent Current
Quiescent Current
GND Pin Current
250
225
200
175
150
125
100
75
1.2
1.0
0.8
0.6
0.4
0.2
0
80
70
60
50
40
30
20
10
0
T
R
V
= 25°C
T
= 25°C
= ∞
J
L
T = 25°C
J
J
L
=
∞
R
*FOR V
= 1.24V
OUT
= 1.24V
OUT
R
I
= 49.6Ω
L
L
V
= V
IN
= 25mA*
SHDN
R
L
= 124Ω
= 10mA*
V
= V
IN
L
SHDN
I
V
= GND
R
L
I
L
= 1.24k
= 1mA*
SHDN
50
25
V
= GND
SHDN
0
0
10 20 30 40 50 60 70 80
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
3013 G06b
3013 G07
3013 G06
GND Pin Current
GND Pin Current vs ILOAD
10
10
9
8
7
6
5
4
3
2
1
0
T
= 25°C, *FOR V
= 1.24V
OUT
V
J
= 4.75V
J
IN
9
8
7
6
5
4
3
2
1
0
T
= 25°C
R
L
= 4.96Ω
L
I
= 250mA*
R
= 12.4Ω
= 100mA*
L
I
L
R
= 24.8Ω, I = 50mA*
L
L
0
1
2
3
4
5
6
7
8
9
10
0
50
100
150
200
250
INPUT VOLTAGE (V)
LOAD CURRENT (mA)
3013 G08
3013 G09
3013fe
6
LT3013
TYPICAL PERFORMANCE CHARACTERISTICS
SHDN Pin Current
SHDN Pin Threshold
SHDN Pin Current
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
0.6
0.5
0.4
0.3
0.2
0.1
0
0.6
0.5
0.4
0.3
0.2
0.1
0
T
= 25°C
V
V
= 6V
J
IN
SHDN
CURRENT FLOWS
= 0V
OUT OF SHDN PIN
CURRENT FLOWS
OUT OF SHDN PIN
OFF-TO-ON
ON-TO-OFF
–50
0
25 50 75 100 125 150
TEMPERATURE (°C)
–25
0
0.5
1.0
1.5
2.0
2.5
3.0
–50
0
25
50
TEMPERATURE (°C)
75 100
125 150
–25
SHDN PIN VOLTAGE (V)
3013 G10
3013 G11
3013 G12
ADJ Pin Bias Current
PWRGD Trip Point
120
95
94
93
92
91
90
89
88
87
86
85
100
80
OUTPUT RISING
OUTPUT FALLING
60
40
20
0
–50
0
25 50 75 100 125 150
TEMPERATURE (°C)
3013 G13
–50
0
25 50 75
125 150
100
–25
–25
TEMPERATURE (°C)
3013 G25
3013fe
7
LT3013
TYPICAL PERFORMANCE CHARACTERISTICS
PWRGD Output Low Voltage
CT Charging Current
CT Comparator Thresholds
200
180
160
140
120
100
80
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
I
= 50μA
PWRGD TRIPPED HIGH
PWRGD
V
(HIGH)
CT
60
40
V
(LOW)
20
CT
0
–50
0
25 50 75 100 125 150
–50
–25
0
25 50 75 100 125 150
TEMPERATURE (°C)
3013 G28
–25
–50
0
25 50 75 100 125 150
TEMPERATURE (°C)
3013 G27
–25
TEMPERATURE (°C)
3013 G26
Current Limit
Current Limit
700
600
500
400
300
200
100
0
1000
V
= 0V
OUT
900
800
700
600
500
400
300
200
100
0
T
= 25°C
J
T
= 125°C
J
V
V
= 7V
IN
OUT
= 0V
0
10 20 30 40 50 60 70 80
–50
0
25 50 75 100 125 150
TEMPERATURE (°C)
–25
INPUT VOLTAGE (V)
3013 G15
3013 G14
3013fe
8
LT3013
TYPICAL PERFORMANCE CHARACTERISTICS
Reverse Output Current
Reverse Output Current
Input Ripple Rejection
92
88
84
80
76
72
68
64
60
120
100
80
200
180
160
140
120
100
80
T
V
V
= 25°C
= 0V
V
V
= 0V
= V
J
IN
IN
OUT
= 1.24V
ADJ
= V
OUT
ADJ
CURRENT FLOWS
INTO OUTPUT PIN
60
ADJ
PIN CLAMP
(SEE APPLICATIONS
INFORMATION)
40
60
40
V
L
V
= 4.75V + 0.5V RIPPLE AT f = 120Hz
P-P
IN
20
0
I
= 250mA
20
= 1.24V
OUT
0
0
1
2
3
4
5
6
7
8
9
10
–50
–25
0
25 50 75 100 125 150
TEMPERATURE (°C)
–50
0
25 50 75
125 150
100
–25
TEMPERATURE (°C)
OUTPUT VOLTAGE (V)
3013 G17
3013 G18
3013 G16
Input Ripple Rejection
Minimum Input Voltage
100
90
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
V
LOAD
= 4.75V + 50mV
RIPPLE
RMS
I
= 250mA
IN
LOAD
I
= 250mA
80
70
60
50
C
= 10μF
OUT
40
30
20
10
0
C
= 3.3μF
OUT
10
100
1k
10k
100k
1M
–50
0
25 50 75 100 125 150
TEMPERATURE (°C)
3013 G20
–25
FREQUENCY (Hz)
3013 G19
3013fe
9
LT3013
TYPICAL PERFORMANCE CHARACTERISTICS
Load Regulation
Output Noise Spectral Density
10
1
0
C
= 3.3μF
= 250mA
ΔI = 1mA TO 250mA
L
OUT
–2
–4
I
LOAD
–6
–8
–10
–12
–14
–16
–18
–20
0.1
0.01
–50
0
25 50 75 100 125 150
TEMPERATURE (°C)
3013 G21
–25
10
100
1k
FREQUENCY (Hz)
10k
100k
10Hz to 100kHz Output Noise
Transient Response
0.15
0.10
0.05
0
V
OUT
–0.05
–0.10
–0.15
300
200
100
0
100μV/DIV
V
V
C
C
= 6V
= 5V
= 3.3μF CERAMIC
IN
OUT
IN
= 3.3μF CERAMIC
LOAD
OUT
ΔI
= 100mA TO 200mA
3013 G23
C
I
OUT
= 10μF
1ms/DIV
OUT
L
= 250mA
V
= 1.24V
0
100
200
300
400
500
TIME (μs)
3013 G24
3013fe
10
LT3013
PIN FUNCTIONS (DFN Package)/(TSSOP Package)
NC (Pins 1, 9, 12)/(Pins 2, 12, 15): No Connect. These
pins have no internal connection; connecting NC pins
to a copper area for heat dissipation provides a small
improvement in thermal performance.
SHDN (Pin 8)/(Pin 11): Shutdown. The SHDN pin is used
to put the LT3013 into a low power shutdown state. The
output will be off when the SHDN pin is pulled low. The
SHDNpincanbedriveneitherby5Vlogicoropen-collector
logic with a pull-up resistor. The pull-up resistor is only
requiredtosupplythepull-upcurrentoftheopen-collector
gate,normallyseveralmicroamperes.Ifunused,theSHDN
OUT (Pins 2, 3)/(Pins 3, 4): Output. The output supplies
power to the load. A minimum output capacitor of 3.3μF is
required to prevent oscillations. Larger output capacitors
will be required for applications with large transient loads
to limit peak voltage transients. See the Applications
Information section for more information on output
capacitance and reverse output characteristics.
pin must be tied to a logic high or V .
IN
C (Pin 7)/(Pin 10): Timing Capacitor. The C pin allows
T
T
the use of a small capacitor to delay the timing between
the point where the output crosses the PWRGD threshold
and the PWRGD flag changes to a high impedance state.
Current out of this pin during the charging phase is
3μA. The voltage difference between the PWRGD low
and PWRGD high states is 1.6V (see the Applications
Information Section).
ADJ (Pin 4)/(Pin 5): Adjust. This is the input to the error
amplifier. This pin is internally clamped to 7V. It has a
bias current of 30nA which flows into the pin (see curve
of ADJ Pin Bias Current vs Temperature in the Typical
Performance Characteristics). The ADJ pin voltage is
1.24V referenced to ground, and the output voltage range
is 1.24V to 60V.
IN (Pins 10, 11)/(Pins 13,14): Input. Power is supplied
to the device through the IN pin. A bypass capacitor is
required on this pin if the device is more than six inches
away from the main input filter capacitor. In general, the
output impedance of a battery rises with frequency, so it is
advisabletoincludeabypasscapacitorinbattery-powered
circuits. A bypass capacitor in the range of 1μF to 10μF is
sufficient. The LT3013 is designed to withstand reverse
voltages on the IN pin with respect to ground and the OUT
pin. In the case of a reversed input, which can happen if
a battery is plugged in backwards, the LT3013 will act as
if there is a diode in series with its input. There will be
no reverse current flow into the LT3013 and no reverse
voltage will appear at the load. The device will protect both
itself and the load.
GND (Pins 5, 13)/(Pins 1, 6, 8, 9, 16, 17): Ground. The
exposedbacksideofthepackageisanelectricalconnection
forGND.Assuch,toensureoptimumdeviceoperationand
thermalperformance,theexposedpadmustbeconnected
directly to Pin 5/Pin 6 on the PC board.
PWRGD (Pin 6)/(Pin 7): Power Good. The PWRGD flag is
an open collector flag to indicate that the output voltage
has come up to above 90% of the nominal output voltage.
There is no internal pull-up on this pin; a pull-up resistor
must be used. The PWRGD pin will change state from an
open-collector to high impedance after both the output is
above 90% of the nominal voltage and the capacitor on
the CT pin has charged through a 1.6V differential. The
maximum pull-down current of the PWRGD pin in the low
state is 50μA.
3013fe
11
LT3013
APPLICATIONS INFORMATION
The LT3013 is a 250mA high voltage low dropout regula-
tor with micropower quiescent current and shutdown.
The device is capable of supplying 250mA at a dropout
voltage of 400mV. The low operating quiescent current
(65μA) drops to 1μA in shutdown. In addition to the
low quiescent current, the LT3013 incorporates several
protection features which make it ideal for use in bat-
tery-powered systems. The device is protected against
both reverse input and reverse output voltages. In battery
backup applications where the output can be held up by
a backup battery when the input is pulled to ground, the
LT3013 acts like it has a diode in series with its output
and prevents reverse current flow.
Note that in shutdown the output is turned off and the
divider current will be zero.
The adjustable device is tested and specified with the
ADJ pin tied to the OUT pin and a 5μA DC load (unless
otherwisespecified)foranoutputvoltageof1.24V. Speci-
fications for output voltages greater than 1.24V will be
proportional to the ratio of the desired output voltage to
1.24V; (V /1.24V). For example, load regulation for an
OUT
outputcurrentchangeof1mAto250mAis–7mVtypicalat
V
OUT
= 1.24V. At V
= 12V, load regulation is:
OUT
(12V/1.24V) • (–7mV) = –68mV
Output Capacitance and Transient Response
Adjustable Operation
The LT3013 is designed to be stable with a wide range of
output capacitors. The ESR of the output capacitor affects
stability, most notably with small capacitors. A minimum
output capacitor of 3.3μF with an ESR of 3ꢀ or less is
recommended to prevent oscillations. The LT3013 is a
micropower device and output transient response will be
a function of output capacitance. Larger values of output
capacitance decrease the peak deviations and provide
improved transient response for larger load current
changes. Bypass capacitors, used to decouple individual
components powered by the LT3013, will increase the
effective output capacitor value.
The LT3013 has an output voltage range of 1.24V to 60V.
The output voltage is set by the ratio of two external
resistors as shown in Figure 1. The device servos the
output to maintain the voltage at the adjust pin at 1.24V
referenced to ground. The current in R1 is then equal to
1.24V/R1 and the current in R2 is the current in R1 plus
the ADJ pin bias current. The ADJ pin bias current, 30nA
at 25°C, flows through R2 into the ADJ pin. The output
voltagecanbecalculatedusingtheformulainFigure1.The
value of R1 should be less than 250k to minimize errors
in the output voltage caused by the ADJ pin bias current.
V
IN
OUT
ADJ
OUT
R2
V
= 1.24V 1 +
= 1.24V
+ (I )(R2)
ADJ
OUT
ADJ
+
R1
LT3013
GND
R2
R1
V
IN
V
I
= 30nA AT 25°C
OUTPUT RANGE = 1.24V TO 60V
ADJ
3013 F01
Figure 1. Adjustable Operation
3013fe
12
LT3013
APPLICATIONS INFORMATION
Extra consideration must be given to the use of ceramic
capacitors. Ceramic capacitors are manufactured with a
variety of dielectrics, each with different behavior across
temperature and applied voltage. The most common
dielectrics used are specified with EIA temperature
characteristiccodesofZ5U,Y5V,X5RandX7R.TheZ5Uand
Y5V dielectrics are good for providing high capacitances
in a small package, but they tend to have strong voltage
and temperature coefficients as shown in Figures 2
and 3. When used with a 5V regulator, a 16V 10μF Y5V
capacitor can exhibit an effective value as low as 1μF to
2μF for the DC bias voltage applied and over the operating
temperature range. The X5R and X7R dielectrics result in
more stable characteristics and are more suitable for use
as the output capacitor. The X7R type has better stability
acrosstemperature, whiletheX5Rislessexpensiveandis
availableinhighervalues.Carestillmustbeexercisedwhen
using X5R and X7R capacitors; the X5R and X7R codes
only specify operating temperature range and maximum
capacitancechangeovertemperature.Capacitancechange
due to DC bias with X5R and X7R capacitors is better than
Y5VandZ5Ucapacitors,butcanstillbesignificantenough
todropcapacitorvaluesbelowappropriatelevels.Capacitor
DC bias characteristics tend to improve as component
casesizeincreases, butexpectedcapacitanceatoperating
voltage should be verified.
Voltage and temperature coefficients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltageacrossitsterminalsduetomechanicalstress,simi-
lartothewayapiezoelectricaccelerometerormicrophone
works. For a ceramic capacitor the stress can be induced
by vibrations in the system or thermal transients.
PWRGD Flag and Timing Capacitor Delay
The PWRGD flag is used to indicate that the ADJ pin volt-
age is within 10% of the regulated voltage. The PWRGD
pin is an open-collector output, capable of sinking 50μA
of current when the ADJ pin voltage is low. There is no
internal pull-up on the PWRGD pin; an external pull-up
resistor must be used. When the ADJ pin rises to within
10% of its final reference value, a delay timer is started.
At the end of this delay, programmed by the value of the
capacitor on the C pin, the PWRGD pin switches to a high
T
impedance and is pulled up to a logic level by an external
pull-up resistor.
To calculate the capacitor value on the C pin, use the
T
following formula:
ICT •tDELAY
CT(HIGH) – VCT(LOW)
CTIME
=
V
40
20
20
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10μF
0
X5R
0
–20
X5R
Y5V
–20
–40
–60
–80
–100
–40
–60
Y5V
–80
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10μF
–100
50
TEMPERATURE (°C)
100 125
–50 –25
0
25
75
0
8
12 14
2
4
6
10
16
DC BIAS VOLTAGE (V)
3013 F03
3013 F02
Figure 2. Ceramic Capacitor DC Bias Characteristics
Figure 3. Ceramic Capacitor Temperature Characteristics
3013fe
13
LT3013
APPLICATIONS INFORMATION
Figure 4 shows a block diagram of the PWRGD circuit. At
startup,thetimingcapacitorisdischargedandthePWRGD
pin will be held low. As the output voltage increases and
the ADJ pin crosses the 90% threshold, the JK flip-flop
is reset, and the 3μA current source begins to charge the
Thermal Considerations
The power handling capability of the device will be limited
by the maximum rated junction temperature (125°C
for LT3013E, LT3013MP or 140°C for LT3013HFE). The
power dissipated by the device will be made up of two
components:
timing capacitor. Once the voltage on the C pin reaches
T
the V
threshold (approximately 1.7V at 25°C), the
CT(HIGH)
1. Output current multiplied by the input/output voltage
capacitor voltage is clamped and the PWRGD pin is set to
a high impedance state.
differential: I
• (V – V ) and,
OUT
IN OUT
2. GND pin current multiplied by the input voltage:
• V .
Duringnormaloperation,aninternalglitchfilterwillignore
shorttransients(<15μs).Longertransientsbelowthe90%
threshold will reset the JK flip-flop. This flip-flop ensures
I
GND
IN
TheGNDpincurrentcanbefoundbyexaminingtheGNDPin
CurrentcurvesintheTypicalPerformanceCharacteristics.
Power dissipation will be equal to the sum of the two
components listed above.
that the capacitor on the C pin is quickly discharged all
T
the way to the V
threshold before re-starting the
CT(LOW)
time delay. This provides a consistent time delay after the
ADJ pin is within 10% of the regulated voltage before the
PWRGD pin switches to high impedance.
The LT3013 has internal thermal limiting designed
to protect the device during overload conditions. For
continuous normal conditions the maximum junction
temperatureratingof125°C(E-grade,MP-grade)or140°C
(H-grade)must not be exceeded. It is important to give
careful consideration to all sources of thermal resistance
fromjunctiontoambient.Additionalheatsourcesmounted
nearby must also be considered.
I
3μA
CT
C
T
PWRGD
+
–
ADJ
V
– V
BE
CT(HIGH)
J
Q
(~1.1V)
K
V
• 90%
REF
–
+
V
CT(LOW)
~0.1V
3013 F04
Figure 4. PWRGD Circuit Block Diagram
3013fe
14
LT3013
APPLICATIONS INFORMATION
For surface mount devices, heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Copper board stiffeners and plated
through-holescanalsobeusedtospreadtheheatgenerated
by power devices.
Calculating Junction Temperature
Example 1: Given an output voltage of 5V, an input voltage
range of 8V to 12V, an output current range of 0mA to
250mA, and a maximum ambient temperature of 30°C,
what will the maximum junction temperature be?
The following tables list thermal resistance for several
different board sizes and copper areas. All measurements
were taken in still air on 3/32” FR-4 board with one ounce
copper.
The power dissipated by the device will be equal to:
I
• (V
– V ) + (I
• V
)
OUT(MAX)
IN(MAX)
OUT
GND
IN(MAX)
where:
Table 1. TSSOP Measured Thermal Resistance
I
= 250mA
= 12V
OUT(MAX)
COPPER AREA
TOPSIDE
THERMAL RESISTANCE
BOARD AREA
2500 sq mm
2500 sq mm
2500 sq mm
2500 sq mm
(JUNCTION-TO-AMBIENT)
V
IN(MAX)
2500 sq mm
1000 sq mm
225 sq mm
100 sq mm
40°C/W
45°C/W
50°C/W
62°C/W
I
at (I = 250mA, V = 12V) = 8mA
OUT IN
GND
So:
P = 250mA • (12V – 5V) + (8mA • 12V) = 1.85W
The thermal resistance will be in the range of 40°C/W to
62°C/W depending on the copper area. So the junction
temperature rise above ambient will be approximately
equal to:
Table 2. DFN Measured Thermal Resistance
COPPER AREA
TOPSIDE
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
BOARD AREA
2500 sq mm
2500 sq mm
2500 sq mm
2500 sq mm
2500 sq mm
1000 sq mm
225 sq mm
100 sq mm
40°C/W
45°C/W
1.85W • 50°C/W = 92.3°C
50°C/W
The maximum junction temperature will then be equal to
the maximum junction temperature rise above ambient
plus the maximum ambient temperature or:
62°C/W
The thermal resistance junction-to-case (θ ), measured
at the exposed pad on the back of the die, is 16°C/W.
JC
T
= 30°C + 92.3°C = 122.3°C
JMAX
Continuous operation at large input/output voltage dif-
ferentials and maximum load current is not practical
due to thermal limitations. Transient operation at high
input/output differentials is possible. The approximate
thermal time constant for a 2500sq mm 3/32” FR-4 board
with maximum topside and backside area for one ounce
copper is three seconds. This time constant will increase
as more thermal mass is added (i.e., vias, larger board,
and other components).
Example 2: Given an output voltage of 5V, an input voltage
of 48V that rises to 72V for 5ms(max) out of every 100ms,
and a 5mA load that steps to 200mA for 50ms out of
every 250ms, what is the junction temperature rise above
ambient? Using a 500ms period (well under the time
constant of the board), power dissipation is as follows:
P1(48V in, 5mA load) = 5mA • (48V – 5V)
+ (200μA • 48V) = 0.23W
Foranapplicationwithtransienthighpowerpeaks,average
power dissipation can be used for junction temperature
calculations if the pulse period is significantly less than
the thermal time constant of the device and board.
P2(48V in, 50mA load) = 200mA • (48V – 5V)
+ (8mA • 48V) = 8.98W
P3(72V in, 5mA load) = 5mA • (72V – 5V)
+ (200μA • 72V) = 0.35W
P4(72V in, 50mA load) = 200mA • (72V – 5V)
+ (8mA • 72V) = 13.98W
3013fe
15
LT3013
APPLICATIONS INFORMATION
Operation at the different power levels is as follows:
Protection Features
76% operation at P1, 19% for P2, 4% for P3, and
1% for P4.
TheLT3013incorporatesseveralprotectionfeatureswhich
make it ideal for use in battery-powered circuits. In ad-
dition to the normal protection features associated with
monolithicregulators,suchascurrentlimitingandthermal
limiting, thedeviceisprotectedagainstreverse-inputvolt-
ages, and reverse voltages from output to input.
P
= 76%(0.23W) + 19%(8.98W) + 4%(0.35W)
EFF
+ 1%(13.98W) = 2.03W
With a thermal resistance in the range of 40°C/W to
62°C/W, this translates to a junction temperature rise
above ambient of 81°C to 125°C.
Current limit protection and thermal overload protection
areintendedtoprotectthedeviceagainstcurrentoverload
conditions at the output of the device. For normal opera-
tion, the junction temperature should not exceed 125°C
(LT3013E, LT3013MP) or 140°C (LT3013HFE).
High Temperature Operation
CaremustbetakenwhendesigningLT3013applicationsto
operate at high ambient temperatures. The LT3013 works
at elevated temperatures but erratic operation can occur
duetounforeseenvariationsinexternalcomponents.Some
tantalum capacitors are available for high temperature
operation, but ESR is often several ohms; capacitor ESR
above 3Ω is unsuitable for use with the LT3013. Ceramic
capacitor manufacturers (Murata, AVX, TDK, and Vishay
Vitramonatthiswriting)nowofferceramiccapacitorsthat
areratedto150°CusinganX8Rdielectric.Deviceinstability
will occur if output capacitor value and ESR are outside
design limits at elevated temperature and operating DC
voltage bias (see information on capacitor characteristics
underOutputCapacitanceandTransientResponse).Check
each passive component for absolute value and voltage
ratings over the operating temperature range.
Like many IC power regulators, the LT3013 has safe oper-
ating area protection. The safe area protection decreases
the current limit as input voltage increases and keeps
the power transistor inside a safe operating region for
all values of input voltage. The protection is designed to
provide some output current at all values of input voltage
up to the device breakdown. The SOA protection circuitry
for the LT3013 uses a current generated when the input
voltage exceeds 25V to decrease current limit. This cur-
rent shows up as additional quiescent current for input
voltages above 25V. This increase in quiescent current
occurs both in normal operation and in shutdown (see
curve of Quiescent Current in the Typical Performance
Characteristics).
Leakages in capacitors or from solder flux left after
insufficient board cleaning adversely affects low
quiescent current operation. The output voltage resistor
divider should use a maximum bottom resistor value of
124k to compensate for high temperature leakage, setting
divider current to 10μA. Consider junction temperature
increase due to power dissipation in both the junction and
nearbycomponentstoensuremaximumspecificationsare
not violated for the device or external components.
The input of the device will withstand reverse voltages of
80V. No negative voltage will appear at the output. The
device will protect both itself and the load. This provides
protection against batteries which can be plugged in
backward.
The ADJ pin of the device can be pulled above or below
ground by as much as 7V without damaging the device.
If the input is left open-circuit or grounded, the ADJ pin
will act like an open-circuit when pulled below ground,
and like a large resistor (typically 100k) in series with a
diode when pulled above ground. If the input is powered
by a voltage source, pulling the ADJ pin below the refer-
ence voltage will cause the device to current limit. This
will cause the output to go to a unregulated high voltage.
Pulling the ADJ pin above the reference voltage will turn
off all output current.
3013fe
16
LT3013
APPLICATIONS INFORMATION
In situations where the ADJ pin is connected to a resistor
divider that would pull the ADJ pin above its 7V clamp
voltageiftheoutputispulledhigh,theADJpininputcurrent
must be limited to less than 5mA. For example, a resistor
divider is used to provide a regulated 1.5V output from the
1.24V reference when the output is forced to 60V. The top
resistor of the resistor divider must be chosen to limit the
current into the ADJ pin to less than 5mA when the ADJ
pin is at 7V. The 53V difference between the OUT and ADJ
pins divided by the 5mA maximum current into the ADJ
pin yields a minimum top resistor value of 10.6k.
open-circuit. Current flow back into the output will follow
the curve shown in Figure 5. The rise in reverse output
current above 7V occurs from the breakdown of the 7V
clamp on the ADJ pin. With a resistor divider on the
regulator output, this current will be reduced depending
on the size of the resistor divider.
When the IN pin of the LT3013 is forced below the OUT
pin or the OUT pin is pulled above the IN pin, input current
will typically drop to less than 2μA. This can happen if
the input of the LT3013 is connected to a discharged
(low voltage) battery and the output is held up by either
a backup battery or a second regulator circuit. The state
of the SHDN pin will have no effect on the reverse output
current when the output is pulled above the input.
In circuits where a backup battery is required, several
different input/output conditions can occur. The output
voltage may be held up while the input is either pulled
to ground, pulled to some intermediate voltage, or is left
200
T
V
V
= 25°C
= 0V
J
IN
180
160
140
120
100
80
= V
OUT
ADJ
CURRENT FLOWS
INTO OUTPUT PIN
ADJ
PIN CLAMP
(SEE ABOVE)
60
40
20
0
0
1
2
3
4
5
6
7
8
9
10
OUTPUT VOLTAGE (V)
3013 F05
Figure 5. Reverse Output Current
3013fe
17
LT3013
TYPICAL APPLICATIONS
5V Buck Converter with Low Current Keep Alive Backup
D2
D1N914
Buck Converter
6
C2
L1†
Efficiency vs Load Current
0.33μF
BOOST
15μH
V
V
IN
OUT
4
2
100
90
80
70
60
50
5.5V*
V
SW
5V
IN
V
= 5V
OUT
L = 68μH
TO 60V
C3
4.7μF
100V
D1
1A/250mA
V
V
= 10V
= 42V
IN
IN
10MQ060N
LT1766
CERAMIC
15
14
10
12
SHDN
BIAS
FB
R1
15.4k
C1
+
100μF 10V
SOLID
SYNC
GND
R2
4.99k
TANTALUM
V
C
1, 8, 9, 16 11
C
C
1nF
14
3
5
0
0.25
0.50
0.75
1.00
1.25
3013 TA03
IN
OUT
LOAD CURRENT (A)
LT3013
*FOR INPUT VOLTAGES BELOW 7.5V,
SOME RESTRICTIONS MAY APPLY
† INCREASE L1 TO 30μH FOR LOAD
CURRENTS ABOVE 0.6A AND TO
60μH ABOVE 1A
OPERATING
CURRENT
100k
750k
249k
11
7
3013 TA04
SHDN
ADJ
HIGH
LOW
PWRGD
GND
C
T
1
10
1000pF
LT3013 Automotive Application
IN
OUT
ADJ
NO PROTECTION
DIODE NEEDED!
+
V
IN
12V
(LATER 42V)
LT3013
GND
750k
249k
3.3μF
1μF
LOAD: CLOCK,
SECURITY SYSTEM
ETC
SHDN
OFF
ON
LT3013 Telecom Application
V
IN
48V
(72V TRANSIENT)
IN
OUT
+
LT3013
GND
750k
249k
BACKUP
BATTERY
NO PROTECTION
DIODE NEEDED!
3.3μF
1μF
LOAD:
SYSTEM MONITOR
ETC
SHDN
ADJ
–
3013 TA05
OFF
ON
3013fe
18
LT3013
PACKAGE DESCRIPTION
DE Package
12-Lead Plastic DFN (4mm × 3mm)
(Reference LTC DWG # 05-08-1695)
0.38 0.10
12
4.00 0.10
(2 SIDES)
R = 0.115
TYP
7
0.65 0.05
R = 0.20
TYP
3.50 0.05
2.20 0.05 (2 SIDES)
1.70 0.05
3.00 0.10 1.70 0.10
(2 SIDES)
(2 SIDES)
PIN 1
TOP MARK
(NOTE 6)
PIN 1
NOTCH
PACKAGE OUTLINE
(UE12/DE12) DFN 0603
6
0.25 0.05
1
0.75 0.05
0.200 REF
0.25 0.05
0.50
BSC
0.50
BSC
3.30 0.10
(2 SIDES)
3.30 0.05
(2 SIDES)
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
NOTE:
1. DRAWING PROPOSED TO BE A VARIATION OF VERSION
(WGED) IN JEDEC PACKAGE OUTLINE M0-229
2. DRAWING NOT TO SCALE
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON THE TOP AND BOTTOM OF PACKAGE
3. ALL DIMENSIONS ARE IN MILLIMETERS
FE Package
16-Lead Plastic TSSOP (4.4mm)
(Reference LTC DWG # 05-08-1663)
Exposed Pad Variation BB
4.90 – 5.10*
(.193 – .201)
3.58
(.141)
3.58
(.141)
16 1514 13 12 1110
9
6.60 0.10
4.50 0.10
2.94
(.116)
6.40
(.252)
BSC
SEE NOTE 4
2.94
(.116)
0.45 0.05
1.05 0.10
0.65 BSC
5
7
8
1
2
3
4
6
RECOMMENDED SOLDER PAD LAYOUT
1.10
(.0433)
MAX
4.30 – 4.50*
(.169 – .177)
0.25
REF
0° – 8°
0.65
(.0256)
BSC
0.09 – 0.20
(.0035 – .0079)
0.50 – 0.75
(.020 – .030)
0.05 – 0.15
(.002 – .006)
0.195 – 0.30
FE16 (BB) TSSOP 0204
(.0077 – .0118)
TYP
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS 4. RECOMMENDED MINIMUM PCB METAL SIZE
FOR EXPOSED PAD ATTACHMENT
*DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.150mm (.006") PER SIDE
MILLIMETERS
(INCHES)
2. DIMENSIONS ARE IN
3. DRAWING NOT TO SCALE
3013fe
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LT3013
TYPICAL APPLICATION
Constant Brightness for Indicator LED over Wide Input Voltage Range
RETURN
IN
OUT
LT3013
1μF
3.3μF
OFF
ON
SHDN
GND
ADJ
R
SET
–48V
–48V CAN VARY
FROM –4V TO –80V
3013 TA06
I
= 1.24V/R
SET
LED
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1020
125mA, Micropower Regulator and Comparator V : 4.5V to 36V, V
= 2.5V, V = 0.4V, I = 40μA, I = 40μA, Comparator
DO Q SD
IN
OUT(MIN)
and Reference, Class B Outputs, S16, PDIP14 Packages
LT1120/LT1120A
125mA, Micropower Regulator and Comparator V : 4.5V to 36V, V
= 2.5V, V = 0.4V, I = 40μA, I = 10μA,
DO Q SD
IN
OUT(MIN)
Comparator and Reference, Logic Shutdown, Ref Sources and Sinks 2/4mA,
S8, N8 Packages
LT1121/LT1121HV 150mA, Micropower, LDO
V : 4.2V to 30/36V, V
= 3.75V, V = 0.42V, I = 30μA, I = 16μA,
IN
OUT(MIN) DO Q SD
Reverse Battery Protection, SOT-223, S8, Z Packages
LT1129
700mA, Micropower, LDO
V : 4.2V to 30V, V = 3.75V, V = 0.4V, I = 50μA, I = 16μA,
IN
OUT(MIN)
DO
Q
SD
DD, S0T-223, S8,TO220-5, TSSOP20 Packages
LT1676
60V, 440mA (I ), 100kHz, High Efficiency
V : 7.4V to 60V, V
= 1.24V, I = 3.2mA, I = 2.5μA, S8 Package
Q SD
OUT
IN
OUT(MIN)
Step-Down DC/DC Converter
LT1761
100mA, Low Noise Micropower, LDO
V : 1.8V to 20V, V
= 1.22V, V = 0.3V, I = 20μA, I = <1μA,
DO Q SD
IN
OUT(MIN)
Low Noise < 20μV
, Stable with 1μF Ceramic Capacitors, ThinSOTTM Package
RMS
LT1762
150mA, Low Noise Micropower, LDO
500mA, Low Noise Micropower, LDO
3A, Low Noise, Fast Transient Response, LDO
V : 1.8V to 20V, V
= 1.22V, V = 0.3V, I = 25μA, I = <1μA,
IN
OUT(MIN) DO Q SD
Low Noise < 20μV
, MS8 Package
RMS
LT1763
V : 1.8V to 20V, V
= 1.22V, V = 0.3V, I = 30μA, I = <1μA,
, S8 Package
IN
OUT(MIN) DO Q SD
Low Noise < 20μV
RMS
LT1764/LT1764A
V : 2.7V to 20V, V
= 1.21V, V = 0.34V, I = 1mA, I = <1μA,
, “A” Version Stable with Ceramic Capacitors,
IN
OUT(MIN) DO Q SD
Low Noise < 40μV
RMS
DD, TO220-5 Packages
LT1766
60V, 1.2A (I ), 200kHz, High Efficiency
V : 5.5V to 60V, V
= 1.2V, I = 2.5mA, I = 25μA, TSSOP16/E Package
Q SD
OUT
IN
OUT(MIN)
OUT(MIN)
Step-Down DC/DC Converter
LT1776
40V, 550mA (I ), 200kHz, High Efficiency
V : 7.4V to 40V, V
IN
= 1.24V, I = 3.2mA, I = 30μA, N8, S8 Packages
OUT
Q
SD
Step-Down DC/DC Converter
LT1934/LT1934-1
LT1956
300mA/60mA, (I ), Constant Off-Time, High
90% Efficiency, V : 3.2V to 34V, V
= 1.25V, I = 14μA, I = <1μA,
OUT
IN
OUT(MIN) Q SD
Efficiency Step-Down DC/DC Converter
ThinSOT Package
60V, 1.2A (I ), 500kHz, High Efficiency
V : 5.5V to 60V, V
= 1.2V, I = 2.5mA, I = 25μA, TSSOP16/E Package
Q SD
OUT
IN
OUT(MIN)
Step-Down DC/DC Converter
LT1962
300mA, Low Noise Micropower, LDO
V : 1.8V to 20V, V
= 1.22V, V = 0.27V, I = 30μA, I = <1μA,
DO Q SD
IN
OUT(MIN)
Low Noise < 20μV
, MS8 Package
RMS
LT1963/LT1963A
1.5A, Low Noise, Fast Transient Response, LDO V : 2.1V to 20V, V
= 1.21V, V = 0.34V, I = 1mA, I = <1μA,
IN
OUT(MIN) DO Q SD
Low Noise < 40μV
, “A” Version Stable with Ceramic Capacitors,
RMS
DD, TO220-5, S0T-223, S8 Packages
LT1964
200mA, Low Noise Micropower, Negative LDO
50mA, 3V to 80V, Low Noise Micropower LDO
V : –1.9V to –20V, V = –1.21V, V = 0.34V, I = 30μA, I = 3μA,
IN
OUT(MIN)
DO
Q
SD
Low Noise < 30μVRMS, Stable with Ceramic Capacitors, ThinSOT Package
LT3010/LT3010H
LT3012/LT3012H
LT3014/HV
V : 3V to 8V, V = 1.275V, V = 0.3V, I = 30μA, I = 1μA,
IN
OUT(MIN)
DO
Q
SD
Low Noise < 100μV
, MS8E Package, H Grade = +140°C T
RMS
JMAX
250mA, 4V to 80V, Low Dropout Micropower
Linear Regulator
V : 4V to 80V, V : 1.24V to 60V, V = 0.4V, I = 40μA, I = <1μA,
IN OUT DO Q SD
TSSOP-16E and 4mm × 3mm DFN-12 Packages, H Grade = +140°C T
JMAX
20mA, 3V to 80V, Low Dropout Micropower
Linear Regulator
V : 3V to 80V (100V for 2ms, HV version), V : 1.22V to 60V, V = 0.35V,
IN OUT DO
I = 7μA, I = <1μA, ThinSOT and 3mm × 3mm DFN-8 Packages
Q
SD
ThinSOT is a trademark of Linear Technology Corporation.
3013fe
LT 0209 REV E • PRINTED IN USA
LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
20
●
●
© LINEAR TECHNOLOGY CORPORATION 2005
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
相关型号:
LT3013HFE#PBF
LT3013 - 250mA, 4V to 80V Low Dropout Micropower Linear Regulator with PWRGD; Package: TSSOP; Pins: 16; Temperature Range: -40°C to 125°C
Linear
LT3013HFE#TR
IC VREG 1.24 V-60 V ADJUSTABLE POSITIVE LDO REGULATOR, 0.62 V DROPOUT, PDSO16, 4.40 MM, PLASTIC, TSSOP-16, Adjustable Positive Single Output LDO Regulator
Linear
LT3013HFE#TRPBF
LT3013 - 250mA, 4V to 80V Low Dropout Micropower Linear Regulator with PWRGD; Package: TSSOP; Pins: 16; Temperature Range: -40°C to 125°C
Linear
LT3013MPFE#PBF
LT3013 - 250mA, 4V to 80V Low Dropout Micropower Linear Regulator with PWRGD; Package: TSSOP; Pins: 16; Temperature Range: -55°C to 125°C
Linear
LT3013MPFE#TRPBF
LT3013 - 250mA, 4V to 80V Low Dropout Micropower Linear Regulator with PWRGD; Package: TSSOP; Pins: 16; Temperature Range: -55°C to 125°C
Linear
©2020 ICPDF网 联系我们和版权申明