LT3407EDD-2 [Linear]
IC 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10, 3 X 3 MM, PLASTIC, MO-229WEED-2, DFN-10, Switching Regulator or Controller;型号: | LT3407EDD-2 |
厂家: | Linear |
描述: | IC 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10, 3 X 3 MM, PLASTIC, MO-229WEED-2, DFN-10, Switching Regulator or Controller 开关 光电二极管 |
文件: | 总16页 (文件大小:221K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LTC3407-2
Dual Synchronous, 800mA,
2.25MHz Step-Down
DC/DC Regulator
U
DESCRIPTIO
FEATURES
The LTC®3407-2 is a dual, constant frequency, synchro-
nous step down DC/DC converter. Intended for low power
applications, it operates from 2.5V to 5.5V input voltage
range and has a constant 2.25MHz switching frequency,
allowing the use of tiny, low cost capacitors and inductors
with a profile ≤1.2mm. Each output voltage is adjustable
from 0.6V to 5V. Internal synchronous 0.35Ω, 1.2A power
switches provide high efficiency without the need for
external Schottky diodes.
■
High Efficiency: Up to 95%
Very Low Quiescent Current: Only 40μA
2.25MHz Constant Frequency Operation
High Switch Current: 1.2A on Each Channel
No Schottky Diodes Required
Low RDS(ON) Internal Switches: 0.35Ω
Current Mode Operation for Excellent Line
■
■
■
■
■
■
and Load Transient Response
Short-Circuit Protected
Low Dropout Operation: 100% Duty Cycle
Ultralow Shutdown Current: IQ < 1μA
Output Voltages from 5V down to 0.6V
Power-On Reset Output
Externally Synchronizable Oscillator
■
■
A user selectable mode input is provided to allow the user
to trade-off noise ripple for low power efficiency. Burst
Mode® operation provides high efficiency at light loads,
while Pulse Skip Mode provides low noise ripple at light
loads.
■
■
■
■
■
Small Thermally Enhanced MSOP and 3mm × 3mm
To further maximize battery life, the P-channel MOSFETs
are turned on continuously in dropout (100% duty cycle),
and both channels draw a total quiescent current of only
40μA. In shutdown, the device draws <1μA.
DFN Packages
U
APPLICATIO S
■
PDAs/Palmtop PCs
■
, LT, LTC, LTM, and Burst Mode are registered trademarks of Linear Technology
Corporation. All other trademarks are the property of their respective owners.
Digital Cameras
Cellular Phones
Portable Media Players
PC Cards
■
■
■
■
Wireless and DSL Modems
U
TYPICAL APPLICATIO
V
= 2.5V*
TO 5.5V
LTC3407-2 Efficiency Curve
IN
R5
100
C1
100k
10μF
RUN2
V
RUN1
POR
IN
95
90
85
80
75
70
65
60
2.5V
MODE/SYNC
RESET
1.8V
LTC3407-2
L2
L1
2.2μH
2.2μH
V
= 2.5V
OUT2
AT 800mA
V
= 1.8V
OUT1
SW2
SW1
AT 800mA
C5, 22pF
C4, 22pF
V
V
FB1
FB2
R4
887k
R2
604k
GND
C3
10μF
C2
10μF
V
= 3.3V
R3
280k
R1
301k
IN
Burst Mode OPERATION
NO LOAD ON OTHER CHANNEL
1
10
100
1000
3407 TA01
C1, C2, C3: TAIYO YUDEN JMK316BJ106ML
L1, L2: MURATA LQH32CN2R2M33
LOAD CURRENT (mA)
*V CONNECTED TO V FOR V ≤ 2.8V
OUT
IN IN
3407 TA02
Figure 1. 2.5V/1.8V at 800mA Step-Down Regulators
34072fa
1
LTC3407-2
W W
U W
ABSOLUTE AXI U RATI GS
(Note 1)
Ambient Operating Temperature Range (Note 2)
LTC3407E-2........................................ –40°C to 85°C
LTC3407I-2 ...................................... –40°C to 125°C
Junction Temperature (Note 5)............................. 125°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec)
VIN Voltages.................................................–0.3V to 6V
VFB1, VFB2, RUN1, RUN2
Voltages ..................................... –0.3V to VIN + 0.3V
MODE/SYNC Voltage ...................... –0.3V to VIN + 0.3V
SW1, SW2 Voltage ......................... –0.3V to VIN + 0.3V
POR Voltage ................................................–0.3V to 6V
MSE Package Only ........................................... 300°C
Reflow Peak Body Temperature............................ 260°C
U
U
U
PI CO FIGURATIO
TOP VIEW
TOP VIEW
V
1
2
3
4
5
10
9
V
FB2
RUN2
POR
SW2
MODE/
SYNC
V
1
2
3
4
5
10
9
V
FB2
FB1
FB1
RUN1
RUN1
RUN2
V
SW1
GND
11
8
IN
11
V
8
POR
SW2
7
6
IN
SW1
GND
7
6
MODE/
SYNC
MSE PACKAGE
10-LEAD PLASTIC MSOP
DD PACKAGE
10-LEAD (3mm × 3mm) PLASTIC DFN
MSE PIN 11, EXPOSED PAD: PGND
MUST BE CONNECTED TO GND
DD PIN 11, EXPOSED PAD: PGND
MUST BE CONNECTED TO GND
TJMAX = 125°C, θJA = 45°C/W, θJC = 10°C/W
TJMAX = 125°C, θJA = 45°C/W, θJC = 10°C/W
U
W
U
ORDER I FOR ATIO
LEAD FREE FINISH
LT3407EDD-2#PBF
LT3407IDD-2#PBF
LT3407EMSE-2#PBF
LT3407IMSE-2#PBF
LEAD BASED FINISH
LT3407EDD-2
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
–40°C to 85°C
–40°C to 125°C
–40°C to 85°C
–40°C to 125°C
TEMPERATURE RANGE
–40°C to 85°C
–40°C to 125°C
–40°C to 85°C
LT3407EDD-2#TRPBF
LT3407IDD-2#TRPBF
LT3407EMSE-2#TRPBF
LT3407IMSE-2#TRPBF
TAPE AND REEL
LBFB
10-Lead (3mm x 3mm) Plastic DFN
10-Lead (3mm x 3mm) Plastic DFN
10-Lead Plastic MSOP
LBFB
LTBDZ
LTBDZ
PART MARKING*
LBFB
10-Lead Plastic MSOP
PACKAGE DESCRIPTION
LT3407EDD-2#TR
LT3407IDD-2#TR
10-Lead (3mm x 3mm) Plastic DFN
10-Lead (3mm x 3mm) Plastic DFN
10-Lead Plastic MSOP
LT3407IDD-2
LBFB
LT3407EMSE-2
LT3407IMSE-2
LT3407EMSE-2#TR
LT3407IMSE-2#TR
LTBDZ
LTBDZ
10-Lead Plastic MSOP
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is indicated by a label on the shipping container
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
34072fa
2
LTC3407-2
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 3.6V, unless otherwise specified. (Note 2)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
5.5
UNITS
V
V
IN
Operating Voltage Range
Feedback Pin Input Current
Feedback Voltage (Note 3)
●
●
2.5
I
30
nA
FB
V
FB
0°C ≤ T ≤ 85°C
0.588
0.585
0.585
0.6
0.6
0.6
0.612
0.612
0.612
V
V
V
A
–40°C ≤ T ≤ 85°C
●
●
A
–40°C ≤ T ≤ 125°C (Note 2)
A
ΔV
ΔV
Reference Voltage Line Regulation
Output Voltage Load Regulation
V
= 2.5V to 5.5V (Note 3)
0.3
0.5
0.5
%/V
%
LINE REG
IN
(Note 3)
LOAD REG
I
Input DC Supply Current
Active Mode
S
V
V
= V = 0.5V
700
40
0.1
950
60
1
μA
μA
μA
FB1
FB2
Sleep Mode
Shutdown
= V = 0.63V, MODE/SYNC = 3.6V
FB1
FB2
RUN = 0V, V = 5.5V, MODE/SYNC = 0V
IN
f
f
I
Oscillator Frequency
V
= 0.6V
FBX
●
1.8
2.25
2.25
1.2
2.7
MHz
MHz
A
OSC
SYNC
LIM
Synchronization Frequency
Peak Switch Current Limit
V
IN
= 3V, V
= 0.5V, Duty Cycle <35%
0.95
1.6
FBX
R
Top Switch On-Resistance
Bottom Switch On-Resistance
(Note 6)
(Note 6)
0.35
0.30
0.45
0.45
Ω
Ω
DS(ON)
I
Switch Leakage Current
V
IN
= 5V, V
= 0V, V = 0V
FBX
0.01
1
μA
SW(LKG)
RUN
POR
Power-On Reset Threshold
V
FBX
V
FBX
Ramping Up, MODE/SYNC = 0V
Ramping Down, MODE/SYNC = 0V
8.5
–8.5
%
%
Power-On Reset On-Resistance
Power-On Reset Delay
RUN Threshold
100
262,144
1
200
Ω
Cycles
V
V
I
●
●
0.3
1.5
1
RUN
RUN Leakage Current
0.01
μA
RUN
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 3: The LTC3407-2 is tested in a proprietary test mode that connects
to the output of the error amplifier.
Note 4: Dynamic supply current is higher due to the internal gate charge
V
FB
being delivered at the switching frequency.
Note 2: The 5LTC3407E-2 is guaranteed to meet specified performance
from 0°C to 70°C. Specifications over the –40°C to 85°C operating
temperature range are assured by design, characterization and correlation
with statistical process controls. The LTC3407I-2 is guaranteed over the
full –40°C to 125°C operating temperature range.
Note 5: T is calculated from the ambient T and power dissipation P
D
J
A
according to the following formula: T = T + (P • θ ).
J
A
D
JA
Note 6: The DFN switch on-resistance is guaranteed by correlation to
wafer level measurements.
U W
TYPICAL PERFOR A CE CHARACTERISTICS TA = 25°C unless other wise specified.
Load Step
Burst Mode Operation
Pulse Skipping Mode
SW
5V/DIV
SW
5V/DIV
V
OUT
200mV/DIV
V
V
I
L
OUT
OUT
100mV/DIV
10mV/DIV
500mA/DIV
I
L
I
I
LOAD
500mA/DIV
L
200mA/DIV
200mA/DIV
3407 G01
3407 G02
3407 G03
V
V
LOAD
= 3.6V
V
V
LOAD
= 3.6V
V
= 3.6V
IN
2μs/DIV
1μs/DIV
20μs/DIV
IN
IN
= 1.8V
= 1.8V
V
= 1.8V
OUT
OUT
OUT
I
= 100mA
I
= 20mA
I
LOAD
CIRCUIT OF FIGURE 1
= 80mA TO 800mA
CIRCUIT OF FIGURE 1
CIRCUIT OF FIGURE 1
34072fa
3
LTC3407-2
U W
TYPICAL PERFOR A CE CHARACTERISTICS TA = 25°C unless other wise specified.
Oscillator Frequency vs Supply
Voltage
Oscillator Frequency vs
Temperature
Efficiency vs Input Voltage
100
95
90
85
80
75
70
65
60
2.5
2.4
2.3
2.2
2.1
2.0
10
8
V
= 3.6V
IN
6
100mA
10mA
1mA
4
2
800mA
0
–2
–4
–6
–8
–10
V
= 1.8V
OUT
Burst Mode OPERATION
CIRCUIT OF FIGURE 1
4
5
6
50
TEMPERATURE (°C)
100 125
4
5
6
2
3
–50 –25
0
25
75
2
3
INPUT VOLTAGE (V)
SUPPLY VOLTAGE (V)
3407 G04
3407 G05
3407 G06
Reference Voltage vs
Temperature
RDS(ON) vs Input Voltage
RDS(ON) vs Temperature
0.615
0.610
0.605
0.600
0.595
0.590
0.585
500
450
400
350
300
250
200
550
500
450
400
350
300
250
200
150
100
V
= 3.6V
V
= 2.7V
IN
T
= 25°C
IN
A
V
= 3.6V
IN
V
= 4.2V
IN
MAIN
SWITCH
SYNCHRONOUS
SWITCH
MAIN SWITCH
SYNCHRONOUS SWITCH
3
2
50
TEMPERATURE (°C)
100 125
5
7
50
TEMPERATURE (°C)
100 125 150
–50 –25
0
25
75
1
4
6
–50 –25
0
25
75
V
(V)
IN
3407 G07
3407 G08
3407 G09
Load Regulation
Efficiency vs Load Current
Efficiency vs Load Current
4
3
100
95
90
85
80
75
70
65
60
100
95
90
85
80
75
70
65
60
2.7V
3.6V
4.2V
Burst Mode OPERATION
Burst Mode OPERATION
2
1
0
PULSE SKIP MODE
–1
–2
–3
–4
PULSE SKIP MODE
V
= 2.5V
OUT
Burst Mode OPERATION
NO LOAD ON OTHER CHANNEL
CIRCUIT OF FIGURE 1
V
= 3.6V, V
= 1.8V
OUT
IN
V
= 3.6V, V
= 1.8V
OUT
IN
NO LOAD ON OTHER CHANNEL
NO LOAD ON OTHER CHANNEL
1
10
100
1000
1
10
100
1000
1
10
100
1000
LOAD CURRENT (mA)
LOAD CURRENT (mA)
LOAD CURRENT (mA)
3407 G12
3407 G10
3407 G11
34072fa
4
LTC3407-2
U W
TYPICAL PERFOR A CE CHARACTERISTICS TA = 25°C unless other wise specified.
Efficiency vs Load Current
Line Regulation
Efficiency vs Load Current
0.5
0.4
100
95
90
85
80
75
70
65
60
100
95
90
85
80
75
70
65
60
V
= 1.8V
OUT
OUT
I
= 200mA
3.6V
T
= 25°C
A
0.3
3.6V
2.7V
2.7V
4.2V
0.2
0.1
0
4.2V
–0.1
–0.2
–0.3
–0.4
–0.5
V
= 1.2V
V
= 1.5V
OUT
OUT
Burst Mode OPERATION
NO LOAD ON OTHER CHANNEL
CIRCUIT OF FIGURE 1
Burst Mode OPERATION
NO LOAD ON OTHER CHANNEL
CIRCUIT OF FIGURE 1
2
6
1
10
100
1000
1
10
100
1000
3
4
5
V
(V)
LOAD CURRENT (mA)
LOAD CURRENT (mA)
IN
3407 G15
3407 G13
3407 G14
U
U
U
PI FU CTIO S
VFB1 (Pin 1): Output Feedback. Receives the feedback
voltage from the external resistive divider across the
output. Nominal voltage for this pin is 0.6V.
be syncronized to an external oscillator applied to this pin
and pulse skipping mode is automatically selected.
SW2 (Pin 7): Regulator 2 Switch Node Connection to the
RUN1 (Pin 2): Regulator 1 Enable. Forcing this pin to VIN
enables regulator 1, while forcing it to GND causes regu-
lator 1 to shut down.
Inductor. This pin swings from VIN to GND.
POR (Pin 8): Power-On Reset . This common-drain logic
output is pulled to GND when the output voltage is not
within 8.5% of regulation and goes high after 117ms
when both channels are within regulation.
VIN (Pin3):MainPowerSupply.Mustbecloselydecoupled
to GND.
SW1 (Pin 4): Regulator 1 Switch Node Connection to the
Inductor. This pin swings from VIN to GND.
RUN2 (Pin 9): Output Feedback. Forcing this pin to VIN
enables regulator 2, while forcing it to GND causes regu-
lator 2 to shut down.
GND (Pin 5): Main Ground. Connect to the (–) terminal of
C
OUT, and (–) terminal of CIN.
VFB2 (Pin 10): Output Feedback. Receives the feedback
voltage from the external resistive divider across the
output. Nominal voltage for this pin is 0.6V.
MODE/SYNC (Pin 6): Combination Mode Selection and
OscillatorSynchronization.Thispincontrolstheoperation
of the device. When tied to VIN or GND, Burst Mode
operation or pulse skipping mode is selected, respec-
tively. Do not float this pin. The oscillation frequency can
Exposed Pad (GND) (Pin 11): Power Ground. Connect to
the (–) terminal of COUT, and (–) terminal of CIN. Must be
connected to electrical ground on PCB.
34072fa
5
LTC3407-2
W
BLOCK DIAGRA
REGULATOR 1
MODE/SYNC
6
BURST
CLAMP
V
IN
SLOPE
COMP
EN
–
+
+
–
0.6V
SLEEP
–
+
I
TH
5Ω
EA
I
COMP
0.35V
V
FB1
1
BURST
Q
S
R
RS
LATCH
Q
0.55V
–
+
SWITCHING
LOGIC
UV
OV
UVDET
OVDET
AND
BLANKING
CIRCUIT
ANTI
SHOOT-
THRU
4
SW1
+
–
0.65V
+
–
I
RCMP
SHUTDOWN
11 GND
V
IN
3
8
V
IN
PGOOD1
POR
2
9
RUN1
RUN2
POR
COUNTER
0.6V REF
OSC
OSC
5
7
GND
PGOOD2
REGULATOR 2 (IDENTICAL TO REGULATOR 1)
10
SW2
V
FB2
U
OPERATIO
Main Control Loop
The LTC3407-2 uses a constant frequency, current mode
architecture. The operating frequency is set at 2.25MHz
and can be synchronized to an external oscillator. Both
channels share the same clock and run in-phase. To suit
a variety of applications, the selectable Mode pin allows
the user to choose between low noise and high efficiency.
Duringnormaloperation,thetoppowerswitch(P-channel
MOSFET) is turned on at the beginning of a clock cycle
when the VFB voltage is below the the reference voltage.
The current into the inductor and the load increases until
the current limit is reached. The switch turns off and
energy stored in the inductor flows through the bottom
switch (N-channel MOSFET) into the load until the next
clock cycle.
The output voltage is set by an external divider returned to
the VFB pins. An error amplfier compares the divided
outputvoltagewithareferencevoltageof0.6Vandadjusts
the peak inductor current accordingly. Overvoltage and
undervoltage comparators will pull the POR output low if
the output voltage is not within 8.5%. The POR output
will go high after 262,144 clock cycles (about 117ms) of
achieving regulation.
The peak inductor current is controlled by the internally
compensated ITH voltage, which is the output of the error
amplifier.This amplifier compares the VFB pin to the 0.6V
reference. When the load current increases, the VFB volt-
age decreases slightly below the reference. This
34072fa
6
LTC3407-2
U
OPERATIO
decrease causes the error amplifier to increase the ITH For lower ripple noise at low currents, the pulse skipping
voltageuntiltheaverageinductorcurrentmatchesthenew modecanbeused. Inthismode, theLTC3407-2continues
to switch at a constant frequency down to very low
currents, where it will begin skipping pulses. The effi-
ciency in pulse skip mode can be improved slightly by
connecting the SW node to the MODE/SYNC input which
reduces the clock frequency by approximately 30%.
load current.
The main control loop is shut down by pulling the RUN pin
to ground.
Low Current Operation
Two modes are available to control the operation of the
LTC3407-2 at low currents. Both modes automatically
switch from continuous operation to the selected mode
when the load current is low.
Dropout Operation
When the input supply voltage decreases toward the
output voltage, the duty cycle increases to 100% which is
the dropout condition. In dropout, the PMOS switch is
turned on continuously with the output voltage being
equal to the input voltage minus the voltage drops across
the internal p-channel MOSFET and the inductor.
To optimize efficiency, the Burst Mode operation can be
selected. When the load is relatively light, the LTC3407-2
automatically switches into Burst Mode operation, in
which the PMOS switch operates intermittently based on
load demand with a fixed peak inductor current. By run-
ning cycles periodically, the switching losses which are
dominatedbythegatechargelossesofthepowerMOSFETs
are minimized. The main control loop is interrupted when
the output voltage reaches the desired regulated value. A
hysteretic voltage comparator trips when ITH is below
0.35V, shuttingofftheswitchandreducingthepower. The
output capacitor and the inductor supply the power to the
load until ITH exceeds 0.65V, turning on the switch and the
main control loop which starts another cycle.
An important design consideration is that the RDS(ON) of
the P-channel switch increases with decreasing input
supplyvoltage(SeeTypicalPerformanceCharacteristics).
Therefore, the user should calculate the power dissipation
when the LTC3407-2 is used at 100% duty cycle with low
input voltage (See Thermal Considerations in the Applica-
tions Information Section).
Low Supply Operation
To prevent unstable operation, the LTC3407-2 incorpo-
rates an Under-Voltage Lockout circuit which shuts down
the part when the input voltage drops below about 1.65V.
W U U
U
APPLICATIO S I FOR ATIO
Accepting larger values of ΔIL allows the use of low
inductances, but results in higher output voltage ripple,
greater core losses, and lower output current capability.
A reasonable starting point for setting ripple current is
ΔIL = 0.3 • ILIM, where ILIM is the peak switch current limit.
The largest ripple current ΔIL occurs at the maximum
input voltage. To guarantee that the ripple current stays
below a specified maximum, the inductor value should be
chosen according to the following equation:
A general LTC3407-2 application circuit is shown in
Figure 2. External component selection is driven by the
load requirement, and begins with the selection of the
inductor L. Once the inductor is chosen, CIN and COUT can
be selected.
Inductor Selection
Although the inductor does not influence the operating
frequency, the inductor value has a direct effect on ripple
current. The inductor ripple current ΔIL decreases with
⎛
⎞
VOUT
VOUT
higher inductance and increases with higher VIN or VOUT
:
L =
• 1–
⎜
⎟
fO • ΔIL
V
IN(MAX)
⎝
⎠
⎛
⎞
VOUT
fO •L
VOUT
ΔIL =
• 1–
⎜
⎟
The inductor value will also have an effect on Burst Mode
V
IN
⎝
⎠
operation. The transition from low current operation
34072fa
7
LTC3407-2
U
W U U
APPLICATIO S I FOR ATIO
Table 1. Representative Surface Mount Inductors
begins when the peak inductor current falls below a level
set by the burst clamp. Lower inductor values result in
higher ripple current which causes this to occur at lower
load currents. This causes a dip in efficiency in the upper
range of low current operation. In Burst Mode operation,
lower inductance values will cause the burst frequency to
increase.
PART
VALUE
DCR
MAX DC
SIZE
3
NUMBER
(μH)
(Ω MAX) CURRENT (A) W × L × H (mm )
Sumida
CDRH3D16
2.2
3.3
4.7
0.075
0.110
0.162
1.20
1.10
0.90
3.8 × 3.8 × 1.8
Sumida
CDRH2D11
1.5
2.2
0.068
0.170
0.900
0.780
3.2 × 3.2 × 1.2
4.4 × 5.8 × 1.2
2.5 × 3.2 × 2.0
2.5 × 3.2 × 2.0
4.5 × 5.4 × 1.2
Inductor Core Selection
Sumida
CMD4D11
2.2
3.3
0.116
0.174
0.950
0.770
Different core materials and shapes will change the size/
current and price/current relationship of an inductor.
Toroid or shielded pot cores in ferrite or permalloy mate-
rials are small and don’t radiate much energy, but gener-
ally cost more than powdered iron core inductors with
similar electrical characterisitics. The choice of which
style inductor to use often depends more on the price vs
size requirements and any radiated field/EMI require-
ments than on what the LTC3407-2 requires to operate.
Table 1 shows some typical surface mount inductors that
work well in LTC3407-2 applications.
Murata
LQH32CN
1.0
2.2
0.060
0.097
1.00
0.79
Toko
D312F
2.2
3.3
0.060
0.260
1.08
0.92
Panasonic
ELT5KT
3.3
4.7
0.17
0.20
1.00
0.95
Output Capacitor (COUT) Selection
The selection of COUT is driven by the required ESR to
minimizevoltagerippleandloadsteptransients.Typically,
once the ESR requirement is satisfied, the capacitance is
adequate for filtering. The output ripple (ΔVOUT) is deter-
mined by:
Input Capacitor (CIN) Selection
In continuous mode, the input current of the converter is
a square wave with a duty cycle of approximately VOUT
/
VIN. To prevent large voltage transients, a low equivalent
series resistance (ESR) input capacitor sized for the maxi-
mum RMS current must be used. The maximum RMS
capacitor current is given by:
⎛
⎞
1
ΔVOUT ≈ ΔIL ESR +
⎜
⎟
8fO COUT
⎝
⎠
where f = operating frequency, COUT = output capacitance
and ΔIL = ripple current in the inductor. The output ripple
is highest at maximum input voltage since ΔIL increases
with input voltage. With ΔIL = 0.3 • ILIM the output ripple
willbelessthan100mVatmaximumVIN andfO =2.25MHz
with:
VOUT (V – VOUT
)
IN
IRMS ≈ IMAX
V
IN
where the maximum average output current IMAX equals
the peak current minus half the peak-to-peak ripple cur-
rent, IMAX = ILIM – ΔIL/2.
ESRCOUT < 150mΩ
This formula has a maximum at VIN = 2VOUT, where IRMS
= IOUT/2. This simple worst-case is commonly used to
design because even significant deviations do not offer
much relief. Note that capacitor manufacturer’s ripple
current ratings are often based on only 2000 hours life-
time. This makes it advisable to further derate the capaci-
tor, or choose a capacitor rated at a higher temperature
thanrequired. Severalcapacitorsmayalsobeparalleledto
meet the size or height requirements of the design. An
additional 0.1μF to 1μF ceramic capacitor is also recom-
mended on VIN for high frequency decoupling, when not
using an all ceramic capacitor solution.
Once the ESR requirements for COUT have been met, the
RMS current rating generally far exceeds the IRIPPLE(P-P)
requirement, except for an all ceramic solution.
In surface mount applications, multiple capacitors may
have to be paralleled to meet the capacitance, ESR or RMS
current handling requirement of the application. Alumi-
numelectrolytic,specialpolymer,ceramicanddrytantulum
capacitorsareallavailableinsurfacemountpackages.The
OS-CONsemiconductordielectriccapacitoravailablefrom
Sanyo has the lowest ESR(size) product of any aluminum
electrolytic at a somewhat higher price. Special polymer
34072fa
8
LTC3407-2
U
W U U
APPLICATIO S I FOR ATIO
capacitors, such as Sanyo POSCAP, Panasonic Special
Polymer (SP), and Kemet A700, offer very low ESR, but
have a lower capacitance density than other types. Tanta-
lum capacitors have the highest capacitance density, but
they have a larger ESR and it is critical that the capacitors
are surge tested for use in switching power supplies. An
excellent choice is the AVX TPS series of surface mount
tantalums, available in case heights ranging from 2mm to
4mm. Aluminum electrolytic capacitors have a signifi-
cantly larger ESR, and are often used in extremely cost-
sensitiveapplicationsprovidedthatconsiderationisgiven
to ripple current ratings and long term reliability. Ceramic
capacitorshavethelowestESRandcost, butalsohavethe
lowest capacitance density, a high voltage and tempera-
ture coefficient, and exhibit audible piezoelectric effects.
In addition, the high Q of ceramic capacitors along with
trace inductance can lead to significant ringing.
requires the designer to check loop stability over the
operating temperature range. To minimize their large
temperature and voltage coefficients, only X5R or X7R
ceramic capacitors should be used. A good selection of
ceramic capacitors is available from Taiyo Yuden, AVX,
Kemet, TDK, and Murata.
Great care must be taken when using only ceramic input
and output capacitors. When a ceramic capacitor is used
at the input and the power is being supplied through long
wires,suchasfromawalladapter,aloadstepattheoutput
can induce ringing at the VIN pin. At best, this ringing can
couple to the output and be mistaken as loop instability. At
worst, the ringing at the input can be large enough to
damage the part.
Since the ESR of a ceramic capacitor is so low, the input
and output capacitor must instead fulfill a charge storage
requirement.Duringaloadstep,theoutputcapacitormust
instantaneously supply the current to support the load
untilthefeedbackloopraisestheswitchcurrentenoughto
support the load. The time required for the feedback loop
to respond is dependent on the compensation and the
output capacitor size. Typically, 3-4 cycles are required to
respond to a load step, but only in the first cycle does the
output drop linearly. The output droop, VDROOP, is usually
about 2-3 times the linear drop of the first cycle. Thus, a
good place to start is with the output capacitor size of
approximately:
In most cases, 0.1μF to 1μF of ceramic capacitors should
also be placed close to the LTC3407-2 in parallel with the
main capacitors for high frequency decoupling.
V = 2.5V
IN
TO 5.5V
C
R5
IN
RUN2
V
RUN1
POR
IN
BM*
POWER-ON
RESET
MODE/SYNC
PS*
LTC3407-2
L1
L2
V
OUT2
SW2
SW1
V
OUT1
C5
R4
C4
R2
V
FB1
V
FB2
GND
R1
C
OUT1
C
R3
OUT2
ΔIOUT
fO •VDROOP
COUT ≈ 2.5
3407 F02
*MODE/SYNC = 0V: PULSE SKIP
MODE/SYNC = V : Burst Mode
IN
More capacitance may be required depending on the duty
cycle and load step requirements.
Figure 2. LTC3407-2 General Schematic
Ceramic Input and Output Capacitors
In most applications, the input capacitor is merely re-
quired to supply high frequency bypassing, since the
impedance to the supply is very low. A 10μF ceramic
capacitor is usually enough for these conditions.
Higher value, lower cost ceramic capacitors are now
becomingavailableinsmallercasesizes.Thesearetempt-
ing for switching regulator use because of their very low
ESR. Unfortunately, the ESR is so low that it can cause
loop stability problems. Solid tantalum capacitor ESR
generatesaloop“zero”at5kHzto50kHzthatisinstrumen-
tal in giving acceptable loop phase margin. Ceramic ca-
pacitors remain capacitive to beyond 300kHz and usually
resonate with their ESL before ESR becomes effective.
Also, ceramic caps are prone to temperature effects which
Setting the Output Voltage
The LTC3407-2 develops a 0.6V reference voltage be-
tween the feedback pin, VFB, and the ground as shown in
Figure 2. The output voltage is set by a resistive divider
according to the following formula:
34072fa
9
LTC3407-2
U
W
U U
APPLICATIO S I FOR ATIO
Checking Transient Response
⎛
⎞
R2
R1
VOUT = 0.6V 1+
⎜
⎟
The regulator loop response can be checked by looking at
the load transient response. Switching regulators take
several cycles to respond to a step in load current. When
a load step occurs, VOUT immediately shifts by an amount
equal to ΔILOAD • ESR, where ESR is the effective series
resistance of COUT. ΔILOAD also begins to charge or
discharge COUT, generating a feedback error signal used
by the regulator to return VOUT to its steady-state value.
During this recovery time, VOUT can be monitored for
overshoot or ringing that would indicate a stability
problem.
⎝
⎠
Keeping the current small (<5μA) in these resistors maxi-
mizes efficiency, but making them too small may allow
stray capacitance to cause noise problems and reduce the
phase margin of the error amp loop.
To improve the frequency response, a feed-forward ca-
pacitor CF may also be used. Great care should be taken to
route the VFB line away from noise sources, such as the
inductor or the SW line.
The initial output voltage step may not be within the
bandwidth of the feedback loop, so the standard second-
order overshoot/DC ratio cannot be used to determine
phase margin. In addition, a feed-forward capacitor, CF,
can be added to improve the high frequency response, as
shown in Figure 2. Capacitor CF provides phase lead by
creating a high frequency zero with R2, which improves
the phase margin.
Power-On Reset
The POR pin is an open-drain output which pulls low when
either regulator is out of regulation. When both output
voltages are within 8.5% of regulation, a timer is started
which releases POR after 218 clock cycles (about 117ms).
This delay can be significantly longer in Burst Mode
operation with low load currents, since the clock cycles
only occur during a burst and there could be milliseconds
of time between bursts. This can be bypassed by tying the
POR output to the MODE/SYNC input, to force pulse
skipping mode during a reset. In addition, if the output
voltage faults during Burst Mode sleep, POR could have a
slight delay for an undervoltage output condition and may
notrespondtoanovervoltageoutput. Thiscanbeavoided
by using pulse skipping mode instead. When either chan-
nel is shut down, the POR output is pulled low, since one
or both of the channels are not in regulation.
The output voltage settling behavior is related to the
stability of the closed-loop system and will demonstrate
the actual overall supply performance. For a detailed
explanation of optimizing the compensation components,
including a review of control loop theory, refer to Applica-
tion Note 76.
In some applications, a more severe transient can be
caused by switching in loads with large (>1μF) input
capacitors.Thedischargedinputcapacitorsareeffectively
put in parallel with COUT, causing a rapid drop in VOUT. No
regulator can deliver enough current to prevent this prob-
Mode Selection & Frequency Synchronization
TheMODE/SYNCpinisamultipurposepinwhichprovides lem, if the switch connecting the load has low resistance
mode selection and frequency synchronization. Connect- and is driven quickly. The solution is to limit the turn-on
ing this pin to VIN enables Burst Mode operation, which speed of the load switch driver. A Hot SwapTM controller is
provides the best low current efficiency at the cost of a designedspecificallyforthispurposeandusuallyincorpo-
higheroutputvoltageripple.Connectingthispintoground rates current limiting, short-circuit protection, and soft-
selects pulse skipping mode, which provides the lowest starting.
output ripple, at the cost of low current efficiency.
Efficiency Considerations
The LTC3407-2 can also be synchronized to an external
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
2.25MHz clock signal by the MODE/SYNC pin. During
synchronization, the mode is set to pulse skipping and the
topswitchturn-onissynchronizedtotherisingedgeofthe
external clock.
Hot Swap is registered trademark of Linear Technology Corporation.
34072fa
10
LTC3407-2
U
W
U U
APPLICATIO S I FOR ATIO
produce the most improvement. Percent efficiency can be
expressed as:
include these “system” level losses in the design of a
system. The internal battery and fuse resistance losses
can be minimized by making sure that CIN has adequate
charge storage and very low ESR at the switching fre-
quency. Other losses including diode conduction losses
during dead-time and inductor core losses generally ac-
count for less than 2% total additional loss.
%Efficiency = 100% - (L1 + L2 + L3 + ...)
whereL1, L2, etc. aretheindividuallossesasapercentage
of input power.
Although all dissipative elements in the circuit produce
losses, 4 main sources usually account for most of the
losses in LTC3407-2 circuits: 1)VIN quiescent current, 2)
switching losses, 3) I2R losses, 4) other losses.
Thermal Considerations
In a majority of applications, the LTC3407-2 does not
dissipate much heat due to its high efficiency. However, in
applications where the LTC3407-2 is running at high
ambient temperature with low supply voltage and high
duty cycles, such as in dropout, the heat dissipated may
exceed the maximum junction temperature of the part. If
the junction temperature reaches approximately 150°C,
both power switches will turn off and the SW node will
become high impedance.
1) The VIN current is the DC supply current given in the
Electrical Characteristics which excludes MOSFET driver
andcontrolcurrents.VIN currentresultsinasmall(<0.1%)
loss that increases with VIN, even at no load.
2) The switching current is the sum of the MOSFET driver
and control currents. The MOSFET driver current results
fromswitchingthegatecapacitanceofthepowerMOSFETs.
Each time a MOSFET gate is switched from low to high to
low again, a packet of charge dQ moves from VIN to
ground. The resulting dQ/dt is a current out of VIN that is
typically much larger than the DC bias current. In continu-
ousmode, IGATECHG =fO(QT +QB), whereQT andQB arethe
gate charges of the internal top and bottom MOSFET
switches. The gate charge losses are proportional to VIN
and thus their effects will be more pronounced at higher
supply voltages.
3) I2R losses are calculated from the DC resistances of the
internal switches, RSW, and external inductor, RL. In
continuousmode,theaverageoutputcurrentflowsthrough
inductor L, but is “chopped” between the internal top and
bottom switches. Thus, the series resistance looking into
the SW pin is a function of both top and bottom MOSFET
RDS(ON) and the duty cycle (DC) as follows:
To prevent the LTC3407-2 from exceeding the maximum
junction temperature, the user will need to do some
thermal analysis. The goal of the thermal analysis is to
determine whether the power dissipated exceeds the
maximum junction temperature of the part. The tempera-
ture rise is given by:
TRISE = PD • θJA
where PD is the power dissipated by the regulator and θJA
is the thermal resistance from the junction of the die to the
ambient temperature.
The junction temperature, TJ, is given by:
TJ = TRISE + TAMBIENT
As an example, consider the case when the LTC3407-2 is
in dropout on both channels at an input voltage of 2.7V
with a load current of 800mA and an ambient temperature
of 70°C. From the Typical Performance Characteristics
graph of Switch Resistance, the RDS(ON) resistance of the
main switch is 0.425Ω. Therefore, power dissipated by
each channel is:
RSW = (RDS(ON)TOP)(DC) + (RDS(ON)BOT)(1 – DC)
The RDS(ON) for both the top and bottom MOSFETs can be
obtained from the Typical Performance Characteristics
curves. Thus, to obtain I2R losses:
I2R losses = IOUT2(RSW + RL)
PD = I2 • RDS(ON) = 272mW
4) Other ‘hidden’ losses such as copper trace and internal
battery resistances can account for additional efficiency
degradations in portable systems. It is very important to
The MS package junction-to-ambient thermal resistance,
θJA, is 45°C/W. Therefore, the junction temperature of the
34072fa
11
LTC3407-2
U
W
U U
APPLICATIO S I FOR ATIO
Board Layout Considerations
regulator operating in a 70°C ambient temperature is
approximately:
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of the
LTC3407-2. These items are also illustrated graphically in
the layout diagram of Figure 3. Check the following in your
layout:
TJ = 2 • 0.272 • 45 + 70 = 94.5°C
which is below the absolute maximum junction tempera-
ture of 125°C.
Design Example
1. Does the capacitor CIN connect to the power VIN (Pin 3)
andGND(exposedpad)ascloseaspossible?Thiscapaci-
torprovidestheACcurrenttotheinternalpowerMOSFETs
and their drivers.
As a design example, consider using the LTC3407-2 in an
portable application with a Li-Ion battery. The battery
provides a VIN = 2.8V to 4.2V. The load requires a maxi-
mum of 800mA in active mode and 2mA in standby mode.
The output voltage is VOUT = 2.5V. Since the load still
needs power in standby, Burst Mode operation is selected
for good low load efficiency.
2. Are the COUT and L1 closely connected? The (–) plate of
COUT returns current to GND and the (–) plate of CIN.
3. The resistor divider, R1 and R2, must be connected
between the (+) plate of COUT and a ground sense line
terminatednearGND(exposedpad). Thefeedbacksignals
VFB should be routed away from noisy components and
traces, such as the SW line (Pins 4 and 7), and its trace
should be minimized.
First, calculate the inductor value for about 30% ripple
current at maximum VIN:
⎛
⎞
2.5V
2.5V
4.2V
L =
• 1–
= 1.5μH
⎜
⎟
2.25MHz • 300mA
⎝
⎠
4.KeepsensitivecomponentsawayfromtheSWpins.The
input capacitor CIN and the resistors R1 to R4 should be
routed away from the SW traces and the inductors.
Choosing a vendor’s closest inductor value of 2.2μH,
results in a maximum ripple current of:
5. Agroundplaneispreferred, butifnotavailable, keepthe
signal and power grounds segregated with small signal
components returning to the GND pin at one point and
⎛
⎞
2.5V
2.5V
4.2V
ΔIL =
• 1−
= 204mA
⎜
⎟
2.25MHz •2.2μ
⎝
⎠
should not share the high current path of CIN or COUT
.
For cost reasons, a ceramic capacitor will be used. COUT
selection is then based on load step droop instead of ESR
requirements. For a 5% output droop:
6. Flood all unused areas on all layers with copper.
Flooding with copper will reduce the temperature rise of
power components. These copper areas should be con-
nected to VIN or GND.
800mA
COUT ≈ 2.5
= 7.1μF
2.25MHz •(5%•2.5V)
V
IN
C
A good standard value is 10μF. Since the output imped-
ance of a Li-Ion battery is very low, CIN is typically 10μF.
The output voltage can now be programmed by choosing
the values of R1 and R2. To maintain high efficiency, the
current in these resistors should be kept small. Choosing
2μA with the 0.6V feedback voltage makes R1~300k. A
close standard 1% resistor is 280k, and R2 is then 887k.
IN
RUN2
V
RUN1
POR
IN
MODE/SYNC
LTC3407-2
L1
C4
L2
V
OUT2
SW2
SW1
V
OUT1
C5
R4
V
V
FB2
FB1
R2
GND
R1
C
OUT1
C
OUT2
R3
The PGOOD pin is a common drain output and requires a
pull-upresistor.A100kresistorisusedforadequate speed.
3407 F03
BOLD LINES INDICATE HIGH CURRENT PATHS
Figure 1 shows the complete schematic for this design
example.
Figure 3. LTC3407-2 Layout Diagram (See Board Layout Checklist)
34072fa
12
LTC3407-2
U
TYPICAL APPLICATIO S
Low Ripple Buck Regulators Using Ceramic Capacitors
V
= 2.5V
IN
TO 5.5V
R5
100k
C1
10μF
RUN2
V
RUN1
POR
IN
POWER-ON
RESET
LTC3407-2
L2
L1
4.7μH
4.7μH
V
= 1.8V
V
= 1.2V
OUT2
OUT1
SW2
SW1
AT 800mA
AT 800mA
C5, 22pF
C4, 22pF
V
V
FB1
FB2
R4
887k
R2
604k
MODE/SYNC GND
C3
10μF
C2
10μF
R3
442k
R1
604k
3407 TA03
C1, C2, C3: TAIYO YUDEN JMK316BJ106ML
L1, L2: SUMIDA CDRH2D18/HP-4R7NC
Efficiency vs Load Current
100
95
90
85
80
75
70
65
60
55
50
1.8V
1.2V
V
= 3.3V
IN
PULSE SKIP MODE
NO LOAD ON OTHER CHANNEL
10
100
1000
LOAD CURRENT (mA)
3407 TA03b
34072fa
13
LTC3407-2
U
TYPICAL APPLICATIO S
2mm Height Core Supply
V
= 3.6V
IN
TO 5.5V
R5
100k
C1*
4.7μF
RUN2
V
RUN1
POR
IN
POWER-ON
RESET
MODE/SYNC
LTC3407-2
L2
L1
2.2μH
2.2μH
V
OUT2
= 3.3V
V
= 1.8V
OUT1
SW2
SW1
AT 800mA
AT 800mA
C5, 22pF
C4, 22pF
V
V
FB2
FB1
R4
887k
R2
604k
C3
C2
GND
R3
196k
R1
301k
4.7μF
4.7μF
×2
×2
3407 TA07
C1, C2, C3: TDK C1608X5ROJ475M
L1, L2: CMD4D11-2R2
*IF C1 IS GREATER THAN 3" FROM POWER SOURCE,
ADDITIONAL CAPACITANCE MAY BE REQUIRED.
Efficiency vs Load Current
100
95
90
85
80
75
70
65
60
3.3V
1.8V
V
= 5V
IN
Burst Mode OPERATION
NO LOAD ON OTHER CHANNEL
1
10
100
1000
LOAD CURRENT (mA)
3407 TA08
34072fa
14
LTC3407-2
U
PACKAGE DESCRIPTIO
DD Package
10-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1699)
R = 0.115
TYP
6
0.38 0.10
10
0.675 0.05
3.50 0.05
2.15 0.05 (2 SIDES)
1.65 0.05
3.00 0.10
(4 SIDES)
1.65 0.10
(2 SIDES)
PIN 1
TOP MARK
(SEE NOTE 6)
PACKAGE
OUTLINE
(DD) DFN 1103
5
1
0.25 0.05
0.50 BSC
0.75 0.05
0.200 REF
0.25 0.05
0.50
BSC
2.38 0.05
(2 SIDES)
2.38 0.10
(2 SIDES)
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2).
CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION ASSIGNMENT
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
MSE Package
10-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1664)
BOTTOM VIEW OF
EXPOSED PAD OPTION
2.06 0.102
3.00 0.102
(.118 .004)
(NOTE 3)
2.794 0.102
(.110 .004)
0.889 0.127
(.035 .005)
0.497 0.076
(.0196 .003)
REF
(.081 .004)
1
10 9
8
7 6
1.83 0.102
(.072 .004)
3.00 0.102
(.118 .004)
(NOTE 4)
5.23
(.206)
MIN
DETAIL “A”
0° – 6° TYP
4.90 0.152
(.193 .006)
2.083 0.102 3.20 – 3.45
(.082 .004) (.126 – .136)
0.254
(.010)
GAUGE PLANE
0.53 0.152
(.021 .006)
1
2
3
4
5
10
0.50
(.0197)
BSC
0.305 0.038
(.0120 .0015)
TYP
0.86
(.034)
REF
1.10
(.043)
MAX
RECOMMENDED SOLDER PAD LAYOUT
DETAIL “A”
0.18
(.007)
SEATING
PLANE
0.17 – 0.27
(.007 – .011)
TYP
0.1016 0.0508
(.004 .002)
0.50
(.0197)
BSC
MSOP (MSE) 0307 REV B
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
34072fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.
15
LTC3407-2
U
TYPICAL APPLICATIO
2mm Height Lithium-Ion Single Inductor Buck-Boost Regulator and a Buck Regulator
V
= 2.8V
IN
TO 4.2V
R5
100k
C1
10μF
RUN2
V
RUN1
POR
IN
POWER-ON
RESET
MODE/SYNC
LTC3407-2
L2
10μH
L1
2.2μH
D1
V = 3.3V
OUT2
AT 200mA
V
= 1.8V
OUT1
SW2
SW1
AT 800mA
C5, 22pF
C4, 22pF
M1
+
C6
47μF
V
V
FB2
FB1
R4
887k
R2
604k
GND
C3
10μF
C2
10μF
R3
196k
R1
301k
3407 TA04
C1, C2, C3: TAIYO YUDEN JMK316BJ106ML
C6: SANYO 6TPB47M
D1: PHILIPS PMEG2010
L1: MURATA LQH32CN2R2M33
L2: TOKO A914BYW-100M (D52LC SERIES)
M1: SILICONIX Si2302
Efficiency vs Load Current
Efficiency vs Load Current
100
95
90
85
80
75
70
65
60
90
80
70
60
50
40
30
2.8V
4.2V
3.6V
4.2V
3.6V
2.8V
V
OUT
= 1.8V
V
OUT
= 3.3V
Burst Mode OPERATION
Burst Mode OPERATION
NO LOAD ON OTHER CHANNEL
NO LOD ON OTHER CHANNEL
1
10
100
1000
1
10
100
1000
LOAD CURRENT (mA)
LOAD CURRENT (mA)
3407 TA06
3407 TA05
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
95% Efficiency, V : 2.7V to 6V, V
LTC1878
600mA (I ), 550kHz,
= 0.8V, I = 10μA,
Q
OUT
IN
OUT(MIN)
Synchronous Step-Down DC/DC Converter
I
<1μA, MSOP-8, Package
SD
LT1940
Dual Output 1.4A(I , Constant 1.1MHz,
V : 3V to 25V, V
= 1.2V, I = 2.5mA, I = <1μA,
OUT)
IN
OUT(MIN)
Q
SD
High Efficiency Step-Down DC/DC Converter
TSSOP-16E Package
LTC3252
Dual 250mA (I ), 1MHz, Spread Spectrum
88% Efficiency, V : 2.7V to 5.5V, V
Q SD
= 0.9V to 1.6V,
OUT
IN
OUT(MIN)
Inductorless Step-Down DC/DC Converter
I = 60μA, I < 1μA, DFN-12 Package
LTC3405/LTC3405A
LTC3406/LTC3406B
LT3407
300mA (I ), 1.5MHz,
96% Efficiency, V : 2.5V to 5.5V, V
SD
= 0.8V, I = 20μA,
OUT
IN
OUT(MIN)
OUT(MIN)
OUT(MIN)
OUT(MIN)
OUT(MIN)
Q
Synchronous Step-Down DC/DC Converters
I
<1μA, ThinSOT Package
600mA (I ), 1.5MHz,
96% Efficiency, V : 2.5V to 5.5V, V
= 0.6V, I = 20μA,
OUT
IN
Q
Synchronous Step-Down DC/DC Converters
I
<1μA, ThinSOT Package
SD
600mA, 1.5MHz
Dual Synchronous Step-Down DC/DC Converter
96% Efficiency, V : 2.5V to 5.5V, V
= 0.6V, I = 40μA,
IN
Q
I
<1μA, MSE, DFN Package
SD
LTC3411
1.25A (I ), 4MHz,
95% Efficiency, V : 2.5V to 5.5V, V
= 0.8V, I = 60μA,
OUT
IN
Q
Synchronous Step Down DC/DC Converter
I
<1μA, MSOP-10 Package
SD
LTC3412
2.5A (I ), 4MHz,
95% Efficiency, V : 2.5V to 5.5V, V
= 0.8V, I = 60μA,
OUT
IN
Q
Synchronous Step Down DC/DC Converter
I
<1μA, TSSOP-16E Package
SD
LTC3414
4A (I ), 4MHz,
95% Efficiency, V : 2.25V to 5.5V, V
SD
= 0.8V, I = 64μA,
OUT
IN
OUT(MIN)
Q
Synchronous Step Down DC/DC Converter
I
<1μA, TSSOP-28E Package
LTC3440
600mA (I ), 2MHz,
95% Efficiency, V : 2.5V to 5.5V, V
SD
= 2.5V, I = 25μA,
OUT
IN
OUT(MIN)
Q
Synchronous Buck-Boost DC/DC Converter
I
<1μA, MSOP-10 Package
34072fa
LT 0707 REV A • PRINTED IN USA
16 LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
●
●
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2004
相关型号:
LT3407EDD-2#PBF
IC 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10, 3 X 3 MM, LEAD FREE, PLASTIC, MO-229WEED-2, DFN-10, Switching Regulator or Controller
Linear
LT3407EDD-2#TR
IC 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10, 3 X 3 MM, PLASTIC, MO-229WEED-2, DFN-10, Switching Regulator or Controller
Linear
LT3407EDD-2#TRPBF
IC 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10, 3 X 3 MM, LEAD FREE, PLASTIC, MO-229WEED-2, DFN-10, Switching Regulator or Controller
Linear
LT3407EMSE-2
IC 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10, PLASTIC, MSOP-10, Switching Regulator or Controller
Linear
LT3407EMSE-2#PBF
IC 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10, PLASTIC, LEAD FREE, MSOP-10, Switching Regulator or Controller
Linear
LT3407EMSE-2#TR
IC 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10, PLASTIC, MSOP-10, Switching Regulator or Controller
Linear
LT3407EMSE-2#TRPBF
IC 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10, PLASTIC, LEAD FREE, MSOP-10, Switching Regulator or Controller
Linear
LT3407IDD-2
Dual Switching Controller, Current-mode, 1.6A, 2700kHz Switching Freq-Max, PDSO10
Linear
LT3407IDD-2#PBF
Dual Switching Controller, Current-mode, 1.6A, 2700kHz Switching Freq-Max, PDSO10
Linear
LT3407IDD-2#TR
IC 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10, 3 X 3 MM, PLASTIC, MO-229WEED-2, DFN-10, Switching Regulator or Controller
Linear
LT3407IDD-2#TRPBF
Dual Switching Controller, Current-mode, 1.6A, 2700kHz Switching Freq-Max, PDSO10
Linear
LT3407IMSE-2
IC 1.6 A DUAL SWITCHING CONTROLLER, 2700 kHz SWITCHING FREQ-MAX, PDSO10, PLASTIC, MSOP-10, Switching Regulator or Controller
Linear
©2020 ICPDF网 联系我们和版权申明