LT6011CS8 [Linear]
Dual/Quad135uA, 14nV/Hz, Rail-to-Rail Output Precision Op Amp; 双/ Quad135uA , 14nV / Hz的轨至轨输出精密运算放大器型号: | LT6011CS8 |
厂家: | Linear |
描述: | Dual/Quad135uA, 14nV/Hz, Rail-to-Rail Output Precision Op Amp |
文件: | 总16页 (文件大小:266K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LT6011/LT6012
Dual/Quad135µA, 14nV/√Hz,
Rail-to-Rail Output
Precision Op Amp
U
FEATURES
DESCRIPTIO
■
60µV Maximum Offset Voltage
The LT®6011/LT6012 op amps combine low noise and
high precision input performance with low power con-
sumption and rail-to-rail output swing.
■
300pA Maximum Input Bias Current
■
135µA Supply Current per Amplifier
■
Rail-to-Rail Output Swing
Input offset voltage is trimmed to less than 60µV. The low
drift and excellent long-term stability guarantee a high
accuracy over temperature and time. The 300pA maxi-
mum input bias current and 120dB minimum voltage gain
further maintain this precision over operating conditions.
■
120dB Minimum Voltage Gain, VS = ±15V
■
0.8µV/°C Maximum VOS Drift
14nV/√Hz Input Noise Voltage
■
■
2.7V to ±18V Supply Voltage Operation
■
Operating Temperature Range: –40°C to 85°C
■
The LT6011/LT6012 work on any power supply voltage
from 2.7V to 36V and draw only 135µA of supply current
ona5Vsupply.Theoutputswingstowithin40mVofeither
supply rail, making the amplifier a good choice for low
voltage single supply applications.
Space Saving 3mm × 3mm DFN Package
U
APPLICATIO S
■
Thermocouple Amplifiers
■
Precision Photo Diode Amplifiers
TheLT6011/LT6012arespecifiedat5Vand±15Vsupplies
and from –40°C to 85°C. The LT6011 (dual) is available in
SO-8 and space saving 3mm × 3mm DFN packages. The
LT6012 (quad) is available in SO-14 and 16-pin SSOP
packages.
■
Instrumentation Amplifiers
■
Battery-Powered Precision Systems
■
Low Voltage Precision Systems
, LTC and LT are registered trademarks of Linear Technology Corporation.
SoftSpan is a trademark of Linear Technology Corporation.
U
TYPICAL APPLICATIO
Low Power Programmable Output Range 16-Bit SoftSpanTM DAC
+
V
S
20V Output Step Response
LT1236-5
5
6
+
7
5V/DIV
0V
1/2 LT6011
SUPPLY CURRENT 1.6mA TO 4mA
DEPENDING ON CODE
–
C2
270pF
2
1
16 15
R2
3
4
5V/DIV
0V
R1
R
R
FB
REF
R
COM
OFS
C1
270pF
R1
R2
+
9
V
S
V
5V
CC
8
0.1µF
I
I
–
OUT1
5
2
3
1
14
13
12
11
10
16-BIT DAC
V
OUT
1/2 LT6011
CLR
CS/LD
SCK
SDI
OUT2
6
7
8
+
100µs/DIV
6011 TA03
4
–
AGND
GND
V
S
LTC1592
SDO
6011 TA01
sn60112 60112fas
1
LT6011/LT6012
W W U W
ABSOLUTE AXI U RATI GS (Note 1)
Total Supply Voltage (V+ to V–) .............................. 40V
Differential Input Voltage (Note 2) .......................... 10V
Input Voltage .................................................... V+ to V–
Input Current (Note 2) ....................................... ±10mA
Output Short-Circuit Duration (Note 3)........... Indefinite
Operating Temperature Range (Note 4) .. –40°C to 85°C
Specified Temperature Range (Note 5)... –40°C to 85°C
Maximum Junction Temperature
DD Package ..................................................... 125°C
All Other Packages .......................................... 150°C
Storage Temperature Range
DD Package ..................................... –65°C to 125°C
All Other Packages .......................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
U W
U
PACKAGE/ORDER I FOR ATIO
ORDER PART
NUMBER
ORDER PART
NUMBER
TOP VIEW
TOP VIEW
LT6011CDD
LT6011IDD
LT6011ACDD
LT6011AIDD
LT6011CS8
+
OUT A
–IN A
+IN A
1
2
3
4
8
7
6
5
V
+
OUT A
–IN A
+IN A
1
2
3
4
8
7
6
5
V
LT6011IS8
OUT B
–IN B
+IN B
A
OUT B
–IN B
+IN B
LT6011ACS8
LT6011AIS8
A
B
–
V
B
–
V
S8 PART MARKING
DD PART MARKING*
LACD
DD PACKAGE
S8 PACKAGE
8-LEAD PLASTIC SO
TJMAX = 150°C, θJA = 190°C/W
8-LEAD (3mm × 3mm) PLASTIC DFN
6011
TJMAX = 125°C, θJA = 160°C/W
UNDERSIDE METAL CONNECTED TO V–
(PCB CONNECTION OPTIONAL)
6011I
6011A
6011AI
TOP VIEW
ORDER PART
NUMBER
ORDER PART
NUMBER
TOP VIEW
OUT A
–IN A
+IN A
1
2
3
4
5
6
7
8
16 OUT D
15 –IN D
OUT A
–IN A
+IN A
1
2
3
4
5
6
7
14
13
12
11
10
9
OUT D
–IN D
+IN D
–
–
+
–
+
A
D +
LT6012CS
LT6012IS
LT6012ACS
LT6012AIS
LT6012CGN
LT6012IGN
LT6012ACGN
LT6012AIGN
–
+
A
B
D
C
14
13
12
11
10
9
+IN D
+
–
V
V
+
–
V
V
+
–
+IN B
–IN B
OUT B
NC
+IN C
–IN C
OUT C
NC
+
+
–
+IN B
–IN B
OUT B
+IN C
–IN C
OUT C
B
C
–
+
–
8
GN PART MARKING
S PACKAGE
14-LEAD PLASTIC SO
6012
GN PACKAGE
16-LEAD PLASTIC SSOP
TJMAX = 150°C, θJA = 135°C/W
6012I
6012A
6012AI
TJMAX = 150°C, θJA = 110°C/W
*Temperature and electrical grades are identified by a label on the shipping container.
Consult LTC Marketing for parts specified with wider operating temperature ranges.
sn60112 60112fas
2
LT6011/LT6012
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 5V, 0V; VCM = 2.5V; RL to 0V; unless otherwise specified. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
Input Offset Voltage (Note 8)
LT6011AS8, LT6012AS
20
60
85
110
µV
µV
µV
OS
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011ADD, LT6012AGN
25
25
30
85
135
170
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011S8, LT6012S
75
100
125
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011DD, LT6012GN
125
175
210
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
∆V /∆T
Input Offset Voltage Drift (Note 6)
Input Offset Current (Note 8)
LT6011AS8, LT6011S8, LT6012AS,LT6012S
LT6011ADD, LT6011DD,LT6012AGN, LT6012GN
●
●
0.2
0.2
0.8
1.2
µV/°C
µV/°C
OS
I
LT6011AS8, LT6011ADD, LT6012AS,
LT6012AGN
OS
20
150
20
300
450
600
pA
pA
pA
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011S8, LT6011DD, LT6012S,
LT6012GN
900
1200
1500
pA
pA
pA
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
I
Input Bias Current (Note 8)
LT6011AS8, LT6011ADD, LT6012AS,
LT6012AGN
B
±300
±450
±600
pA
pA
pA
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011S8, LT6011DD, LT6012S,
LT6012GN
150
±900
±1200
±1500
pA
pA
pA
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
Input Noise Voltage
0.1Hz to 10Hz
400
14
nV
P-P
e
Input Noise Voltage Density
Input Noise Current Density
Input Resistance
f = 1kHz
nV/√Hz
pA/√Hz
n
i
f = 1kHz, Unbalanced Source Resistance
0.1
n
R
IN
Common Mode, V = 1V to 3.8V
Differential
10
120
20
GΩ
MΩ
CM
C
V
Input Capacitance
4
pF
IN
Input Voltage Range (Positive)
Input Voltage Range (Negative)
Guaranteed by CMRR
Guaranteed by CMRR
●
●
3.8
4
0.7
V
V
CM
1
CMRR
Common Mode Rejection Ratio
Minimum Supply Voltage
V
= 1V to 3.8V
●
●
●
107
135
2.4
dB
V
CM
Guaranteed by PSRR
2.7
PSRR
Power Supply Rejection Ratio
Large-Signal Voltage Gain
V = 2.7V to 36V, V = 1/2V
S
112
135
dB
S
CM
A
R = 10k, V = 1V to 4V
OUT
R = 2k, V
●
●
300
250
2000
2000
V/mV
V/mV
VOL
L
= 1V to 4V
L
OUT
Channel Separation
V
= 1V to 4V
●
110
140
dB
OUT
sn60112 60112fas
3
LT6011/LT6012
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = 5V, 0V; VCM = 2.5V; RL to 0V; unless otherwise specified. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
Maximum Output Swing
(Positive, Referred to V )
No Load, 50mV Overdrive
35
55
65
mV
mV
OUT
+
●
●
●
●
●
●
I
= 1mA, 50mV Overdrive
120
40
170
220
mV
mV
SOURCE
Maximum Output Swing
(Negative, Referred to 0V)
No Load, 50mV Overdrive
55
65
mV
mV
I
= 1mA, 50mV Overdrive
= 0V, 1V Overdrive, Source
= 5V, –1V Overdrive, Sink
150
14
225
275
mV
mV
SINK
I
Output Short-Circuit Current (Note 3)
V
V
10
4
mA
mA
SC
OUT
OUT
10
4
21
mA
mA
SR
Slew Rate
A = –10, R = 50k, R = 5k
0.06
0.05
0.04
0.09
V/µs
V/µs
V/µs
V
F
G
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
GBW
Gain Bandwidth Product
f = 10kHz
250
225
330
kHz
kHz
●
t
Settling Time
A = –1, 0.01%, V = 1.5V to 3.5V
OUT
45
1
µs
µs
s
V
t , t
Rise Time, Fall Time
Offset Voltage Match (Note 7)
A = 1, 10% to 90%, 0.1V Step
V
r
f
∆V
LT6011AS8, LT6012AS
50
120
170
220
µV
µV
µV
OS
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011ADD, LT6012AGN
50
50
60
170
270
340
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011S8, LT6012S
150
200
250
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011DD, LT6012GN
250
350
420
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
∆I
B
Input Bias Current Match (Note 7)
LT6011AS8, LT6011ADD, LT6012AS,
LT6012AGN
50
600
900
1200
pA
pA
pA
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011S8, LT6011DD, LT6012S,
LT6012GN
1800
2400
3000
pA
pA
pA
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
∆CMRR
∆PSRR
Common Mode Rejection Ratio
Match (Note 7)
●
101
106
135
135
135
dB
Power Supply Rejection Ratio
Match (Note 7)
●
dB
I
Supply Current
per Amplifier
150
190
210
µA
µA
µA
S
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
sn60112 60112fas
4
LT6011/LT6012
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = ±15V, VCM = 0V, RL to 0V, unless otherwise specified. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
Input Offset Voltage (Note 8)
LT6011AS8, LT6012AS
30
135
160
185
µV
µV
µV
OS
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011ADD, LT6012AGN
35
35
40
160
210
225
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011S8, LT6012S
150
175
200
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011DD, LT6012GN
200
250
275
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
∆V /∆T
Input Offset Voltage Drift (Note 6)
Input Offset Current (Note 8)
LT6011AS8, LT6011S8, LT6012AS, LT6012S
LT6011ADD, LT6011DD, LT6012AGN, LT6012GN
●
●
0.2
0.2
0.8
1.3
µV/°C
µV/°C
OS
I
LT6011AS8, LT6011ADD, LT6012AS LT6012AGN
20
150
20
300
450
600
pA
pA
pA
OS
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011S8, LT6011DD, LT6012S, LT6012GN
900
1200
1500
pA
pA
pA
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
I
Input Bias Current (Note 8)
LT6011AS8, LT6011ADD, LT6012AS, LT6012AGN
±300
±450
±600
pA
pA
pA
B
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011S8, LT6011DD, LT6012S, LT6012GN
150
±900
±1200
±1500
pA
pA
pA
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
Input Noise Voltage
0.1Hz to 10Hz
400
13
nV
P-P
e
Input Noise Voltage Density
Input Noise Current Density
Input Resistance
f = 1kHz
nV/√Hz
pA/√Hz
n
i
f = 1kHz, Unbalanced Source Resistance
0.1
n
R
IN
Common Mode, V = ±13.5V
Differential
50
400
20
GΩ
MΩ
CM
C
V
Input Capacitance
4
pF
V
IN
Input Voltage Range
Guaranteed by CMRR
●
±13.5
±14
CM
CMRR
Common Mode Rejection Ratio
V
= –13.5V to 13.5V
115
112
135
135
dB
dB
CM
●
●
●
Minimum Supply Voltage
Power Supply Rejection Ratio
Large-Signal Voltage Gain
Guaranteed by PSRR
V = ±1.35V to ±18V
±1.2
135
±1.35
V
PSRR
112
dB
S
A
V
R = 10k, V = –13.5V to 13.5V
OUT
1000
600
2000
V/mV
V/mV
VOL
OUT
L
●
R = 5k, V
= –13.5V to 13.5V
OUT
500
300
1500
V/mV
V/mV
L
●
●
Channel Separation
V
= –13.5V to 13.5V
120
140
45
dB
OUT
Maximum Output Swing
No Load, 50mV Overdrive
80
100
mV
mV
+
(Positive, Referred to V )
●
●
●
●
I
= 1mA, 50mV Overdrive
140
45
195
240
mV
mV
SOURCE
Maximum Output Swing
No Load, 50mV Overdrive
= 1mA, 50mV Overdrive
80
100
mV
mV
–
(Negative, Referred to V )
I
150
250
300
mV
mV
SINK
sn60112 60112fas
5
LT6011/LT6012
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VS = ±15V, VCM = 0V, RL to 0V, unless otherwise specified. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
I
Output Short-Circuit Current
(Note 3)
V
= 0V, 1V Overdrive (Source)
10
5
15
mA
mA
SC
OUT
OUT
●
●
V
= 0V, –1V Overdrive (Sink)
10
5
20
mA
mA
SR
Slew Rate
A = –10, R = 50k, R = 5k
0.08
0.07
0.05
0.11
V/µs
V/µs
V/µs
V
F
G
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
GBW
Gain Bandwidth Product
f = 10kHz
275
250
350
kHz
kHz
●
t
Settling Time
A = –1, 0.01%, V = 0V to 10V
OUT
85
1
µs
µs
s
V
t , t
Rise Time, Fall Time
Offset Voltage Match (Note 7)
A = 1, 10% to 90%, 0.1V Step
V
r
f
∆V
LT6011AS8, LT6012AS
50
270
320
370
µV
µV
µV
OS
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011ADD, LT6012AGN
50
70
80
50
320
420
450
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011S8, LT6012S
300
350
400
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011DD, LT6012GN
400
500
550
µV
µV
µV
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
∆I
B
Input Bias Current Match (Note 7)
LT6011AS8, LT6011ADD, LT6012AS, LT6012AGN
600
900
1200
pA
pA
pA
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
LT6011S8, LT6011DD, LT6012S, LT6012GN
1800
2400
3000
pA
pA
pA
T = 0°C to 70°C
●
●
A
T = –40°C to 85°C
A
∆CMRR
∆PSRR
Common Mode Rejection Ratio
Match (Note 7)
●
109
106
135
135
260
dB
Power Supply Rejection Ratio
Match (Note 7)
●
dB
I
Supply Current
per Amplifier
A
T = –40°C to 85°C
A
330
380
400
µA
µA
µA
S
T = 0°C to 70°C
●
●
Note 1: Absolute Maximum Ratings are those beyond which the life if the
device may be impaired.
Note 6: This parameter is not 100% tested.
Note 7: Matching parameters are the difference between any two
Note 2: The inputs are protected by back-to-back diodes and internal
series resistors. If the differential input voltage exceeds 10V, the input
current must be limited to less than 10mA.
amplifiers. ∆CMRR and ∆PSRR are defined as follows: (1) CMRR and
PSRR are measured in µV/V for the individual amplifiers. (2) The
difference between matching amplifiers is calculated in µV/V. (3) The
result is converted to dB.
Note 3: A heat sink may be required to keep the junction temperature
below absolute maximum ratings.
Note 4: Both the LT6011C/LT6012C and LT6011I/LT6012I are guaranteed
functional over the operating temperature range of –40°C to 85°C.
Note 5: The LT6011C/LT6012C are guaranteed to meet the specified
performance from 0°C to 70°C and is designed, characterized and
expected to meet specified performance from –40°C to 85°C but is not
tested or QA sampled at these temperatures. The LT6011I/LT6012I are
guaranteed to meet specified performance from –40°C to 85°C.
Note 8: The specifications for V , I , and I depend on the grade and on
the package. The following table clarifies the notations.
OS B OS
STANDARD GRADE
A GRADE
S8 Package
LT6011S8
LT6011DD
LT6012S
LT6011AS8
LT6011ADD
LT6012AS
LT6012AGN
DFN Package
S14 Package
GN16 Package
LT6012GN
sn60112 60112fas
6
LT6011/LT6012
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Input Offset Voltage
Offset Voltage
vs Temperature
Distribution of Input Offset Voltage
vs Input Common Mode Voltage
125
100
75
30
25
120
100
80
V
= 5V, 0V
= 25°C
LT6011S8,
LT6012S
V = 5V, 0V
S
REPRESENTATIVE UNITS
V = ±15V
S
TYPICAL PART
S
A
T
50
20
T
= 85°C
A
25
60
T
A
= –40°C
= 25°C
0
15
10
40
–25
–50
–75
–100
–125
T
A
20
5
0
0
–20
–50
0
25
50
75 100 125
–25
–90 –70 –50 –30 –10 10 30 50 70 90
–15 –10
–5
0
5
10
15
TEMPERATURE (°C)
INPUT OFFSET VOLTAGE (µV)
INPUT COMMON MODE VOLTAGE (V)
6011 G02
6011 G01
6011 G03
Input Bias Current
vs Input Common Mode Voltage
Input Bias Current vs Temperature
Distribution of Input Bias Current
25
20
15
10
5
1600
1400
1200
1000
800
600
400
200
0
300
200
100
0
V
T
= 5V, 0V
= 25°C
LT6011A,
LT6012A
V
= 5V, 0V
V
= ±15V
S
A
S
S
TYPICAL PART
TYPICAL PART
13.9V
T
= 85°C
A
T
= –40°C
A
T
= 25°C
A
–14.2V
–10
–
–100
–200
I
B
+
I
B
0
–200
–400 –300 –200 –100
0
100 200 300 400
–15
–5
0
5
10
15
–50 –25
0
25
125
50
75 100
INPUT BIAS CURRENT (pA)
COMMON MODE VOLTAGE (V)
TEMPERATURE (°C)
6011 G04
1635 G06
6011 G05
Total Input Noise
vs Source Resistance
0.1Hz to 10Hz Noise
en, in vs Frequency
10
1
1000
100
V
T
= 5V, 0V
S
A
V
T
= ±15V
= 25°C
S
A
= 25°C
f = 1kHz
UNBALANCED
SOURCE RESISTORS
CURRENT NOISE
UNBALANCED
SOURCE RESISTORS
0.1
TOTAL NOISE
100
0.01
0.001
0.0001
RESISTOR NOISE ONLY
VOLTAGE NOISE
100
10
100
1k
10k 100k
1M
10M 100M
0
1
2
3
4
5
6
7
8
9
10
1
10
1000
SOURCE RESISTANCE (Ω)
FREQUENCY (Hz)
TIME (SEC)
6011 G08
6011 G07
6011 G09
sn60112 60112fas
7
LT6011/LT6012
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Output Saturation Voltage
Output Voltage Swing
0.01Hz to 1Hz Noise
vs Load Current (Output High)
vs Temperature
+
1
V
V = 5V, 0V
S
V
T
= ±15V
= 25°C
V
= 5V, 0V
S
S
NO LOAD
A
–20
–40
T
= 85°C
A
OUTPUT HIGH
–60
T
= 25°C
A
0.1
60
40
20
T
= –40°C
OUTPUT LOW
A
–
0.01
V
0.01
0.1
1
10
0
10 20 30 40 50 60 70 80 90 100
–25
0
50
75 100 125
–50
25
LOAD CURRENT (mA)
TIME (SEC)
TEMPERATURE (°C)
6011 G12
6011 G10
6011 G11
Output Saturation Voltage
vs Load Current (Output Low)
Warm-Up Drift
Supply Current vs Supply Voltage
1
3
2
1
0
500
450
400
350
300
250
200
150
100
50
V
= 5V, 0V
S
PER AMPLIFIER
±15V
T
= 85°C
A
T
= 85°C
A
T
= 25°C
A
T
= 25°C
A
0.1
T
= –40°C
A
±2.5V
T
= –40°C
A
0.01
0
0.01
0.1
1
10
30
60
90
120
150
0
2
4
6
8
10 12 14 16 18 20
LOAD CURRENT (mA)
TIME AFTER POWER-ON (SECONDS)
SUPPLY VOLTAGE (±V)
6011 G13
6011 G15
6011 G14
THD + Noise vs Frequency
THD + Noise vs Frequency
Settling Time vs Output Step
10
1
10
1
10
8
V
S
A
V
= ±15V
= 1
V
V
T
= 5V, 0V
= 2V
V
V
T
= ±15V
S
OUT
A
V
V
S
= 20V
P-P
IN P-P
= 25°C
= 25°C
A
A
= 1: R = 10k
L
A
= –1: R = R = 10k
F
G
0.1
6
0.1
0.1%
0.01%
A
= –1
0.01
0.001
0.0001
0.01
0.001
0.0001
V
4
2
0
A
= –1
V
A
= 1
V
A
= 1
V
0
10 20 30 40 50 60 70 80 90
10
100
1k
FREQUENCY (Hz)
10k
100k
10
100
1k
10k
SETTLING TIME (µs)
FREQUENCY (Hz)
6011 G16
6011 G17
6011 G18
sn60112 60112fas
8
LT6011/LT6012
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Settling Time vs Output Step
Channel Separation vs Frequency
CMRR vs Frequency
160
140
120
100
80
10
8
160
140
120
100
80
V
T
= 5V, 0V
= 25°C
V
S
A
V
= ±15V
= –1
T
= 25°C
A
S
A
6
0.1%
V
= ±15V
S
0.01%
V
S
= 5V, 0V
4
2
0
60
60
40
40
20
20
0
0
0
10 20 30 40 50 60 70 80 90
1
10
100
1k
10k 100k
1M
1
10
100
1k
10k 100k
1M
SETTLING TIME (µs)
FREQUENCY (Hz)
FREQUENCY (Hz)
6011 G20
6011 G21
6011 G19
PSRR vs Frequency
Output Impedance vs Frequency
Open-Loop Gain vs Frequency
1000
100
10
140
120
100
80
140
120
100
80
V
T
= 5V, 0V
= 25°C
V
T
= 5V, 0V
S
A
V
T
= 5V, 0V
S
A
S
= 25°C
= 25°C
A
R
= 10k
L
60
A
= 100
V
+PSRR
40
60
1
–PSRR
20
A
= 10
V
40
0
0.1
0.01
20
A
= 1
–20
–40
V
0
0.1
1
10 100 1k 10k 100k 1M
FREQUENCY (Hz)
1
10
100
1k
10k 100k
1M
0.01 0.1
1
10 100 1k 10k 100k 1M 10M
FREQUENCY (Hz)
FREQUENCY (Hz)
6011 G23
6011 G24
6011 G22
Gain vs Frequency, AV = 1
Gain vs Frequency, AV = –1
Gain and Phase vs Frequency
10
5
10
5
60
50
–80
V
T
= 5V, 0V
= 25°C
V
T
= 5V, 0V
S
A
S
A
V
= 5V, 0V
= 25°C
= 10k
S
A
L
= 25°C
T
R
40
–120
–160
–200
–240
–280
C
= 500pF
L
C
= 500pF
L
30
0
0
GAIN
C
= 50pF
L
20
C
= 50pF
L
PHASE
–5
–5
10
0
–10
–15
–20
–10
–15
–20
–10
–20
–30
–40
1k
10k
100k
1M
1k
10k
100k
1M
1k
10k
100k
FREQUENCY (Hz)
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
6011 G25
6011 G26
6011 G27
sn60112 60112fas
9
LT6011/LT6012
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Small-Signal Transient Response
Large-Signal Transient Response
Rail-to-Rail Output Swing
5V
0V
20mV/DIV
2V/DIV
0V
1V/DIV
AV = 1
2µs/DIV
6011 G28
A
V = –1
50µs/DIV
6011 G29
A
V = –1
100µs/DIV
6011 G30
VS = ±15V
VS = 5V, 0V
W U U
U
APPLICATIO S I FOR ATIO
Preserving Input Precision
series with either input. This internal protection limits the
input current to approximately 10mA (the maximum al-
lowed) for a 10V differential input voltage. Use additional
external series resistors to limit the input current to 10mA
in applications where differential inputs of more than 10V
areexpected. Forexample, a1kresistorinserieswitheach
input provides protection against 30V differential voltage.
Preserving the input accuracy of the LT6011/LT6012 re-
quires that the applications circuit and PC board layout do
notintroduceerrorscomparabletoorgreaterthanthe25µV
typical offset of the amplifiers. Temperature differentials
across the input connections can generate thermocouple
voltagesof10’sofmicrovoltssotheconnectionstotheinput
leads should be short, close together and away from heat
dissipatingcomponents.Aircurrentsacrosstheboardcan
also generate temperature differentials.
Input Common Mode Range
The LT6011/LT6012 output is able to swing close to each
power supply rail (rail-to-rail out), but the input stage is
limitedtooperatingbetweenV–+1VandV+–1.2V.Exceed-
ing this common mode range will cause the gain to drop
to zero, however, no phase reversal will occur.
Theextremelylowinputbiascurrents(20pAtypical)allow
high accuracy to be maintained with high impedance
sources and feedback resistors. The LT6011/LT6012 low
input bias currents are obtained by a cancellation circuit
on-chip. This causes the resulting IB and IB to be
uncorrelated, as implied by the IOS specification being
comparabletoIB.Donottrytobalancetheinputresistances
ineachinputlead;insteadkeeptheresistanceateitherinput
as low as possible for maximum accuracy.
+
–
Total Input Noise
TheLT6011/LT6012amplifiercontributesnegligiblenoise
to the system when driven by sensors (sources) with
impedance between 20kΩ and 1MΩ. Throughout this
range, total input noise is dominated by the 4kTRS noise
of the source. If the source impedance is less than 20kΩ,
the input voltage noise of the amplifier starts to contribute
withaminimumnoiseof14nV/√Hzforverylowsourceim-
pedance. If the source impedance is more than 1MΩ, the
input current noise of the amplifier, multiplied by this high
impedance, starts to contribute and eventually dominate.
Total input noise spectral density can be calculated as:
Leakage currents on the PC board can be higher than the
inputbiascurrent.Forexample,10GΩofleakagebetween
a 15V supply lead and an input lead will generate 1.5nA!
Surround the input leads with a guard ring driven to the
samepotentialastheinputcommonmodetoavoidexces-
sive leakage in high impedance applications.
Input Protection
2
n(TOTAL) = en + 4kTRS +(inRS)2
The LT6011/LT6012 feature on-chip back-to-back diodes
between the input devices, along with 500Ω resistors in
v
sn60112 60112fas
10
LT6011/LT6012
W U U
APPLICATIO S I FOR ATIO
U
Rail-to-Rail Operation
where en = 14nV/√Hz , in = 0.1pA/√Hz and RS is the total
impedance at the input, including the source impedance.
TheLT6011/LT6012outputscanswingtowithinmillivolts
of either supply rail, but the inputs can not. However, for
mostopampconfigurations, theinputsneedtoswingless
thantheoutputs.Figure1showsthebasicopampconfigu-
rations,listswhathappenstotheopampinputsandspeci-
fieswhetherornottheopampmusthaverail-to-railinputs.
Select a rail-to-rail input op amp only when really neces-
sary,becausetheinputprecisionspecificationsareusually
inferior.
Capacitive Loads
TheLT6011/LT6012candrivecapacitiveloadsupto500pF
inunitygain.Thecapacitiveloaddrivingcapabilityincreases
astheamplifierisusedinhighergainconfigurations.Asmall
series resistance between the output and the load further
increases the amount of capacitance that the amplifier can
drive.
V
+
–
V
+
–
V
IN
+
–
REF
IN
R
G
V
IN
R
R
F
F
6011 F01
R
G
V
REF
INVERTING: A = –R /R
NONINVERTING: A = 1 + R /R
NONINVERTING: A = 1
V
V
F
G
V
F
G
OP AMP INPUTS DO NOT MOVE,
BUT ARE FIXED AT DC BIAS
INPUTS MOVE BY AS MUCH AS
INPUTS MOVE BY AS MUCH AS
OUTPUT
V
, BUT THE OUTPUT MOVES
IN
POINT V
MORE
REF
INPUT MUST BE RAIL-TO-RAIL
FOR OVERALL CIRCUIT
RAIL-TO-RAIL PERFORMANCE
INPUT DOES NOT HAVE TO BE
RAIL-TO-RAIL
INPUT MAY NOT HAVE TO BE
RAIL-TO-RAIL
Figure 1. Some Op Amp Configurations Do Not Require Rail-to-Rail Inputs to Achieve Rail-to-Rail Outputs
W
W
SI PLIFIED SCHE ATIC
(One Amplifier)
+
V
R6
R3
Q7
R4
R5
Q18
Q19
Q6
C1
Q8
R
C1
Q5
Q4
Q13
Q3
C2
Q21
B
A
D3
D4
D5
OUT
Q22
Q12
Q16
C3
R1
500Ω
Q14
Q17
C
Q20
–IN
B
A
D1
D2
+IN
R2
500Ω
Q1
Q2
Q11
Q9
Q15
Q10
–
6011 SS
V
sn60112 60112fas
11
LT6011/LT6012
U
PACKAGE DESCRIPTIO
DD Package
8-Lead Plastic DFN (3mm × 3mm)
(Reference LTC DWG # 05-08-1698)
R = 0.115
0.38 ± 0.10
TYP
5
8
0.675 ±0.05
3.5 ±0.05
2.15 ±0.05 (2 SIDES)
1.65 ±0.05
3.00 ±0.10
(4 SIDES)
1.65 ± 0.10
(2 SIDES)
PIN 1
TOP MARK
PACKAGE
OUTLINE
(DD8) DFN 0203
4
1
0.28 ± 0.05
0.75 ±0.05
0.200 REF
0.28 ± 0.05
0.50 BSC
0.50
BSC
2.38 ±0.05
(2 SIDES)
2.38 ±0.10
(2 SIDES)
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
NOTE:
1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-1)
2. ALL DIMENSIONS ARE IN MILLIMETERS
3. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
4. EXPOSED PAD SHALL BE SOLDER PLATED
sn60112 60112fas
12
LT6011/LT6012
U
PACKAGE DESCRIPTIO
S8 Package
8-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.189 – .197
(4.801 – 5.004)
.045 ±.005
NOTE 3
.050 BSC
7
5
8
6
.245
MIN
.160 ±.005
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
.030 ±.005
TYP
1
3
4
2
RECOMMENDED SOLDER PAD LAYOUT
.010 – .020
(0.254 – 0.508)
× 45°
.053 – .069
(1.346 – 1.752)
.004 – .010
(0.101 – 0.254)
.008 – .010
(0.203 – 0.254)
0°– 8° TYP
.016 – .050
(0.406 – 1.270)
.050
(1.270)
BSC
.014 – .019
(0.355 – 0.483)
TYP
NOTE:
INCHES
1. DIMENSIONS IN
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
SO8 0303
sn60112 60112fas
13
LT6011/LT6012
U
PACKAGE DESCRIPTIO
S14 Package
14-Lead Plastic Small Outline (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1610)
.337 – .344
.045 ±.005
(8.560 – 8.738)
.050 BSC
N
NOTE 3
13
12
11
10
8
14
N
9
.245
MIN
.160 ±.005
.150 – .157
(3.810 – 3.988)
NOTE 3
.228 – .244
(5.791 – 6.197)
1
2
3
N/2
N/2
7
.030 ±.005
TYP
RECOMMENDED SOLDER PAD LAYOUT
1
2
3
4
5
6
.010 – .020
(0.254 – 0.508)
× 45°
.053 – .069
(1.346 – 1.752)
.004 – .010
(0.101 – 0.254)
.008 – .010
(0.203 – 0.254)
0° – 8° TYP
.050
(1.270)
BSC
.014 – .019
(0.355 – 0.483)
TYP
.016 – .050
(0.406 – 1.270)
S14 0502
NOTE:
1. DIMENSIONS IN
INCHES
(MILLIMETERS)
2. DRAWING NOT TO SCALE
3. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
sn60112 60112fas
14
LT6011/LT6012
U
PACKAGE DESCRIPTIO
GN Package
16-Lead Plastic SSOP (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1641)
.189 – .196*
(4.801 – 4.978)
.045 ±.005
.009
(0.229)
REF
16 15 14 13 12 11 10 9
.254 MIN
.150 – .165
.229 – .244
.150 – .157**
(5.817 – 6.198)
(3.810 – 3.988)
.0165 ±.0015
.0250 TYP
RECOMMENDED SOLDER PAD LAYOUT
1
2
3
4
5
6
7
8
.015 ± .004
(0.38 ± 0.10)
× 45°
.053 – .068
(1.351 – 1.727)
.004 – .0098
(0.102 – 0.249)
.007 – .0098
(0.178 – 0.249)
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
.0250
(0.635)
BSC
.008 – .012
(0.203 – 0.305)
NOTE:
1. CONTROLLING DIMENSION: INCHES
INCHES
2. DIMENSIONS ARE IN
(MILLIMETERS)
GN16 (SSOP) 0502
3. DRAWING NOT TO SCALE
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
sn60112 60112fas
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.
15
LT6011/LT6012
U
TYPICAL APPLICATIO
Low Power Hall Sensor Amplifier
V
S
3
2
8
HALL ELEMENT
ASAHI-KASEI
HW-108A (RANK D)
www.asahi-kasei.co.jp
+
1
V
S
1/2 LT6011
4
–
2
6
1
LT1790-1.25
1, 2
49.9k
10k
OFFSET
7.87k
400Ω
×4
V
S
V
ADJUST
OUT
1k
1%
49.9k
+
–
3
4
100k
1%
LT1782
6
5
–
V
S
= 3V TO 18V
S
7
26.7k
1%
1/2 LT6011
I
= ~600µA
V
OUT
= ~40mV/mT
+
4
6011 TA02
RELATED PARTS
PART NUMBER
LT1112/LT1114
LT1880
DESCRIPTION
COMMENTS
Dual/Quad Low Power, Picoamp Input Precision Op Amp
Rail-to-Rail Output, Picoamp Input Precision Op Amp
250pA Input Bias Current
SOT-23
LT1881/LT1882
LT1884/LT1885
Dual/Quad Rail-to-Rail Output, Picoamp Input Precision Op Amp
C
Up to 1000pF
LOAD
Dual/Quad Rail-to-Rail Output, Picoamp Input Precision Op Amp 9.5nV/√Hz Input Noise
sn60112 60112fas
LT/TP 0903 1K REV A • PRINTED IN USA
16 LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
●
●
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
LINEAR TECHNOLOGY CORPORATION 2003
相关型号:
LT6011CS8#PBF
LT6011 - Dual/Quad 135µA, 14nV/rtHz, Rail-to-Rail Output Precision Op Amp; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LT6011CS8#TR
LT6011 - Dual/Quad 135µA, 14nV/rtHz, Rail-to-Rail Output Precision Op Amp; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LT6011CS8#TRPBF
LT6011 - Dual/Quad 135µA, 14nV/rtHz, Rail-to-Rail Output Precision Op Amp; Package: SO; Pins: 8; Temperature Range: 0°C to 70°C
Linear
LT6011IDD#PBF
LT6011 - Dual/Quad 135µA, 14nV/rtHz, Rail-to-Rail Output Precision Op Amp; Package: DFN; Pins: 8; Temperature Range: -40°C to 85°C
Linear
LT6011IS8#TR
LT6011 - Dual/Quad 135µA, 14nV/rtHz, Rail-to-Rail Output Precision Op Amp; Package: SO; Pins: 8; Temperature Range: -40°C to 85°C
Linear
LT6012ACGN#TR
LT6012 - Dual/Quad 135µA, 14nV/rtHz, Rail-to-Rail Output Precision Op Amp; Package: SSOP; Pins: 16; Temperature Range: 0°C to 70°C
Linear
LT6012ACGN#TRPBF
LT6012 - Dual/Quad 135µA, 14nV/rtHz, Rail-to-Rail Output Precision Op Amp; Package: SSOP; Pins: 16; Temperature Range: 0°C to 70°C
Linear
©2020 ICPDF网 联系我们和版权申明