LTC1064-2MS [Linear]
IC SWITCHED CAPACITOR FILTER, BUTTERWORTH, LOWPASS, PDSO14, PLASTIC, SO-14, Active Filter;型号: | LTC1064-2MS |
厂家: | Linear |
描述: | IC SWITCHED CAPACITOR FILTER, BUTTERWORTH, LOWPASS, PDSO14, PLASTIC, SO-14, Active Filter |
文件: | 总12页 (文件大小:120K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LTC1064-2
Low Noise, High Frequency,
8th Order Butterworth Lowpass Filter
U
FEATURES
DESCRIPTIO
The LTC®1064-2 is a monolithic 8th order lowpass
Butterworth filter, which provides a maximally flat pass-
band. The attenuation slope is –48dB/octave and the
maximum attenuation is in excess of 80db. An external
TTL or CMOS clock programs the filter’s cutoff frequency.
The clock to cutoff frequency ratio is 100:1 (Pin 10 at
V–) or 50:1 (Pin 10 at V+). The maximum cutoff frequency
is 140kHz. No external components are needed.
■
8th Order Filter in a 14-Pin Package
■
140kHz Maximum Corner Frequency
■
No External Components
50:1 and 100:1 Clock to Cutoff Frequency Ratio
80µVRMS Total Wideband Noise
0.03% THD or Better
Operates from ±2.37V to ±8V Power Supplies
■
■
■
■
U
The LTC1064-2 features low wideband noise and low
harmonic distortion even for input voltages up to 3VRMS
In fact the LTC1064-2 overall performance competes with
equivalent multiple op amp RC active realizations. The
LTC1064-2 is available in a 14-pin DIP or 16-pin surface
mounted SW package. The LTC1064-2 is fabricated using
LTC’s enhanced analog CMOS Si-gate process.
APPLICATIO S
.
■
Antialiasing Filters
■
Smoothing Filters
■
Tracking High Frequency Lowpass Filters
The LTC1064-2 is pin compatible with the LTC1064-1.
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATIO
8th Order Clock Sweepable
Lowpass Butterworth Filter
Measured Frequency Response
0
1
2
3
4
5
6
7
14
13
12
11
10
9
OUT C
LTC1064-2
V
= ±7.5V
NC
S
–15
–30
–45
–60
–75
–90
–105
NC
V
IN
–
–8V
V
AGND
+
CLOCK = 5MHz
8V
f
CLK
V
50/100
AGND
NC
V
OUT
8
NC
R
A
IN
1064 TA01a
400
100 200 300
FREQUENCY (kHz)
600 700
0
500
NOTE: THE POWER SUPPLIES SHOULD BE BYPASSED BY A 0.1µF
CAPACITOR CLOSE TO THE PACKAGE. THE NC PINS 1, 6, 8,
AND 13 SHOULD BE PREFERABLY GROUNDED.
1064-2 TA01b
10642fa
1
LTC1064-2
W W
U W
ABSOLUTE AXI U RATI GS
(Note 1)
Total Supply Voltage (V+ to V–)............................ 16.5V
Power Dissipation.............................................. 400mW
Storage Temperature Range ................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
Operating Temperature Range
LTC1064-2M (OBSOLETE) ............... –55°C to 125°C
LTC1064-2C ....................................... –40°C to 85°C
U
W
U
PACKAGE/ORDER I FOR ATIO
TOP VIEW
ORDER PART
NUMBER
ORDER PART
1
2
3
4
5
6
7
OUT C
NC
14
13
12
11
10
9
TOP VIEW
NC
NUMBER
V
IN
NC
1
2
3
4
5
6
7
8
OUT C
NC
16
15
14
13
12
–
V
AGND
LTC1064-2CN
LTC1064-2CSW
V
IN
+
f
–
V
CLK
AGND
V
50/100
+
AGND
NC
V
NC
V
OUT
AGND
NC
f
CLK
NC
8
R
A
IN
11 50/100
10 NC
NC
N PACKAGE
14-LEAD PDIP
9
R
A
V
OUT
IN
TJMAX = 150°C, θJA = 110°C/W
J PACKAGE
SW PACKAGE
14-LEAD CERDIP
16-LEAD PLASTIC (WIDE) SO
LTC1064-2MJ
LTC1064-2CJ
TJMAX = 150°C, θJA = 130°C/W
OBSOLETE PACKAGE
Consider the N14 Package for Alternate Source
Consult LTC Marketing for parts specified with wider operating temperature ranges.
The ■ denotes the specifications which apply over the full operating
ELECTRICAL CHARACTERISTICS
otherwise specified.
temperature range, otherwise specifications are at TA = 25°C. VS = ±7.5V, 100:1, fCLK = 2MHz, R1 = 10k, TTL clock input level unless
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Passband Gain (Note 2)
Gain TempCo
–3dB Frequency
Referenced to 0dB, 1Hz to 1kHz
■
–0.5
0.15
dB
dB/°C
kHz
kHz
dB
0.0002
20
40
100:1
50:1
Gain at –3dB Frequency
Stopband Attenuation
Stopband Attenuation
Stopband Attenuation
Stopband Attenuation
Referenced to 0dB, f = 20kHz
■
■
■
–3
–2.75
IN
At 1.5f
, 50:1, f = 60kHz
–24
–44
–27
–47
–74
–90
dB
dB
dB
dB
–3dB
IN
At 2f
At 3f
At 4f
, 100:1, f = 40kHz
–3dB
–3dB
–3dB
IN
, 100:1, f = 60kHz
IN
, 100:1, f = 80kHz
IN
Input Frequency Range
100:1
50:1
0
0
<f /2
kHz
kHz
CLK
<f
CLK
Output Voltage Swing and
Operating Input Voltage Range
V = ±2.37V
■
■
■
±1.1
±3.1
±5.0
V
V
V
S
V = ±5V
S
V = ±7.5V
S
Total Harmonic Distortion
Wideband Noise
V = ±5V, Input = 1V
V = ±7.5V, Input = 3V
S
at 1kHz
RMS
0.015
0.03
%
%
S
at 1kHz
RMS
V = ±5V, Input = GND 1Hz – 1.99MHz
80
90
µV
µV
S
RMS
RMS
V = ±7.5V, Input = GND 1Hz – 1.99MHz
S
10642fa
2
LTC1064-2
The ■ denotes the specifications which apply over the full operating
ELECTRICAL CHARACTERISTICS
otherwise specified.
temperature range, otherwise specifications are at TA = 25°C. VS = ±7.5V, 100:1, fCLK = 2MHz, R1 = 10k, TTL clock input level unless
PARAMETER
CONDITIONS
V = ±7.5V
V = ±5V
S
MIN
TYP
MAX
UNITS
Output DC Offset (Note 2)
Output DC Offset TempCo
±30
±90
±125
mV
µV/°C
S
Input Impedance
10
20
2
kΩ
Ω
Output Impedance
f
= 10kHz
OUT
Output Short-Circuit Current
Clock Feedthrough
Source/Sink
3/1
200
mA
µV
RMS
Maximum Clock Frequency
50% Duty Cycle, V = ±5V
5
7
MHz
MHz
S
50% Duty Cycle, T = 25°C, V = ±7.5V
A
S
Power Supply Current
V = ±2.37V, f
= 1MHz
CLK
= 1MHz
■
■
11
14
22
23
26
28
32
mA
mA
mA
mA
mA
S
V = ±5V, f
S
CLK
V = ±7.5V, f
S
= 1MHz
CLK
17
■
■
Power Supply Voltage Range
±2.37
±8
V
Note 1: Absolute Maximum Ratings are those values beyond which the life
Note 2: For tighter specifications please contact LTC Marketing.
of a device may be impaired.
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Amplitude Response
Phase Response
Group Delay vs Frequency
45
0
15
0
220
200
180
160
140
120
100
80
V
T
= ±7.5V
= 25°C
= 1MHz
V
T
= ±7.5V
= 25°C
S
A
S
A
f
= 7MHz
CLK
f–3dB = 140kHz
f
f
= 1MHz
CLK
–45
CLK
100:1
100:1
f
= 2MHz
–15
–30
–45
–60
–75
–90
–105
CLK
–90
f
= 10kHz
f
= 10kHz
f–3dB = 40kHz
–3dB
–3dB
–135
–180
–225
–270
–315
–360
–405
–450
f
= 5MHz
CLK
f–3dB = 100kHz
60
40
V
= ±7.5V; 50:1
= 25°C
S
A
20
T
0
10k
100k
(Hz)
1M
0
1
2
3
4
5
6
7
8
9 10 11
0
1
2
3
4
5
6
7
8
9
10 11
f
f
(kHz)
f
IN
(kHz)
IN
IN
1064 G01
1064 G02
1064 G03
10642fa
3
LTC1064-2
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Phase vs f–3dB Frequency
Phase Matching
Noise Spectral Density
2.4
2.0
1.6
1.2
0.8
0.4
0
30
0
1600
1400
1200
V
= ±7.5V, f
= 1MHz, f
= 20kHz, 50:1
–3dB
S
CLK
f
= 2MHz
= 40kHz
CLK
50 UNIT SAMPLE (TA = 25°C TO 125°C)
f
–3dB
–30
f
= 500kHz
= 5kHz
CLK
–3dB
f
= 500kHz
–3dB
CLK
–60
100:1, f
(1060)
1000
f
= 10kHz
–90
f
= 1MHz
= 20kHz
CLK
800
–120
–150
–180
–210
–240
–270
f
–3dB
f
= 2MHz
= 20kHz
CLK
–3dB
600
100:1, f
100:1, f
(530)
400
(335)
f
= 5MHz
= 50kHz
CLK
–3dB
200
V
50:1
= ±7.5V
S
0
0.1k
0
8
12
16
20
24
4
100
1k
FREQUENCY (Hz)
10k
1k
10k
100k
FREQUENCY (kHz)
FREQUENCY (Hz)
1064 G04
1064-2 G05
1064-2 G06
Harmonic Distortion vs Frequency
Harmonic Distortion vs Amplitude
1
0.1
f
= 1MHz, f
= 20kHz, 50:1
–3dB
CLK
±2.5V
±5V
±5V, 1V
INPUT
RMS
±7V
0.1
0.01
±7.5V, 3V
INPUT
RMS
0.01
f
= 1MHz, f = 20kHz
–3dB
CLK
50:1, 1kHz INPUT
0.001
0.001
0.5
1.0
5.0
1k
10k
20k
AMPLITUDE (V
)
RMS
FREQUENCY (Hz)
1064-2 G08
1064-2 G07
Amplitude Response with Pin 10
at Ground
Power Suppy vs Current
48
44
40
36
32
28
24
20
16
12
8
15
0
PIN 10 AT GROUND
=1MHz
f
CLK
–15
–30
–45
–60
–75
–90
–105
T
= –55°C
= 25°C
A
A
T
T
= 125°C
A
4
0
0
2
4
6
8
10 12 14 16 18 20 22 24
1
10
(kHz)
100
f
IN
POWER SUPPLY VOLTAGE (V)
1064-2 G10
1064 G09
10642fa
4
LTC1064-2
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Table 1. Gain/Delay, f–3dB = 1kHz,
Table 3. Gain/Delay, f–3dB = 1kHz,
LTC1064-2 Typical Response VS = ±5V, TA = 25°C,
fCLK = 100kHz, Ratio = Pin 10 at V– (fltr 100:1)
LTC1064-2 Typical Response VS = ±5V, TA = 25°C,
fCLK = 50kHz, Ratio = Pin 10 at V+ (fltr 50:1)
FREQUENCY (kHz)
0.200
GAIN (dB)
–0.213
–0.240
–0.260
–0.280
–0.310
–0.370
–0.530
–1.200
–3.370
–7.500
–12.640
DELAY (ms)
0.821
0.837
0.858
0.893
0.947
1.034
1.172
1.325
1.346
1.158
0.899
FREQUENCY (kHz)
0.200
GAIN (dB)
–0.247
–0.270
–0.290
–0.300
–0.320
–0.370
–0.520
–1.200
–3.380
–7.530
–12.670
DELAY (ms)
0.857
0.872
0.893
0.929
0.983
1.071
1.210
1.364
1.381
1.192
0.935
0.300
0.300
0.400
0.400
0.500
0.500
0.600
0.600
0.700
0.700
0.800
0.800
0.900
0.900
1.000
1.000
1.100
1.100
1.200
1.200
Table 2. Gain, f–3dB = 1kHz,
Table 4. Gain, f–3dB = 1kHz,
LTC1064-2 Typical Response VS = ±5V, TA = 25°C,
LTC1064-2 Typical Response VS = ±5V, TA = 25°C,
fCLK = 50kHz, Ratio = Pin 10 at V+ (fltr 50:1)
fCLK = 100kHz, Ratio = Pin 10 at V– (fltr 100:1)
FREQUENCY (kHz)
0.500
GAIN (dB)
FREQUENCY (kHz)
0.500
GAIN (dB)
–0.298
–3.380
–0.279
–3.370
1.000
1.000
1.500
–27.500
–47.200
–63.300
–75.190
–86.100
–95.310
–104.240
–109.650
–121.930
–123.920
–114.150
–116.990
–120.070
–113.470
–130.090
–114.770
–117.760
1.500
–27.500
–47.200
–62.300
–75.130
–86.090
–95.210
–103.030
–108.690
–114.830
–120.540
–114.750
–116.430
–120.790
–121.290
–119.970
–120.020
–125.170
2.000
2.000
2.500
2.500
3.000
3.000
3.500
3.500
4.000
4.000
4.500
4.500
5.000
5.000
5.500
5.500
6.000
6.000
6.500
6.500
7.000
7.000
7.500
7.500
8.000
8.000
8.500
8.500
9.000
9.000
9.500
9.500
10642fa
5
LTC1064-2
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Table 5. Gain, f–3dB = 20kHz,
Table 6. Gain, f–3dB = 140kHz,
LTC1064-2 Typical Response VS = ±7.5V, TA = 25°C,
LTC1064-2 Typical Response VS = ±7.5V, TA = 25°C,
fCLK = 1MHz, Ratio = Pin 10 at V+ (fltr 50:1)
fCLK = 7MHz, Ratio = Pin 10 at V+ (fltr 50:1)
FREQUENCY (kHz)
10.000
GAIN (dB)
–0.308
FREQUENCY (kHz)
50.00
GAIN (dB)
–0.238
–0.140
0.050
20.000
–3.350
60.00
30.000
–27.400
–47.100
–62.300
–74.890
–85.430
–95.070
–103.150
–108.700
–107.520
–108.030
–104.990
–106.090
–105.320
70.00
40.000
80.00
0.350
50.000
90.00
0.810
60.000
100.00
110.00
120.00
130.00
140.00
150.00
160.00
170.00
180.00
190.00
200.00
210.00
220.00
230.00
240.00
250.00
260.00
270.00
280.00
290.00
300.00
1.450
70.000
2.110
80.000
1.830
90.000
–0.700
–4.840
–9.350
–13.690
–17.760
–21.600
–25.200
–28.500
–31.800
–34.800
–37.700
–40.500
–43.200
–45.700
–48.200
–50.500
–52.700
–54.900
100.000
110.000
120.000
130.000
140.000
150.000
Table 7. Gain Non-Butterworth Response (Pin 10 to GND),
LTC1064-2 Typical Response VS = ±5V, TA = 25°C,
fCLK = 100kHz
FREQUENCY (kHz)
0.500
GAIN (dB)
–0.012
1.000
1.240
1.500
–14.690
–28.600
–41.100
–52.500
–62.800
–71.500
–79.370
–86.730
–93.340
–99.350
–105.270
–113.270
–114.600
–114.010
–122.810
–122.980
–119.450
2.000
2.500
3.000
3.500
4.000
4.500
5.000
5.500
6.000
6.500
7.000
7.500
8.000
8.500
9.000
9.500
10642fa
6
LTC1064-2
U
U
U
PI FU CTIO S (Pin Numbers Refer to the 14-Pin Package)
NC(Pins1,6,8and13):The“noconnection”pinsshould
be preferably grounded. These pins are not internally
connected.
RIN A,OUTC(Pins7,14):Averyshortconnectionbetween
Pin 7 and Pin 14 is recommended. This connection should
be preferably done under the IC package. In a breadboard
use a one inch, or less, shielded coaxial cable: the shield
should be grounded. In a PC board, use a one inch trace or
less; surround the trace by a ground plane.
VIN, VOUT (Pins 2, 9): The input Pin 2 is connected to an
18k resistor tied to the inverting input of an op amp. Pin
2 is protected against static discharge. The device’s
output, Pin 9, is the output of an op amp which can
typically source/sink 3mA/1mA. Although the internal op
amps are unity gain stable, driving long coax cables is not
recommended.
50/100 (Pin 10): The DC level at this pin determines the
ratio of clock frequency to the –3dB frequency of the filter.
The ratio is 50:1 when Pin 10 is at V+ and 100:1 when
Pin 10 is at V–. This pin should be bypassed with a 0.1µF
capacitor to analog ground when it’s connected to V– or V+
(Figure1). SeeTables1through7fortypicalgainanddelay
responses for the two ratios.
When testing the device for noise and distortion, the
output, Pin 9, should be buffered. (Figure 1) The op amp
power supply wire (or trace) should be connected
directly to the power source. To eliminate switching
transients from filter output, buffer filter output with a
third order lowpass (Figure 5).
fCLK (Pin 11): For ±5V supplies the logic threshold level is
1.4V. For ±8V and 0V to 5V supplies the logic threshold
levels are 2.2V and 3V respectively. The logic threshold
levels vary ±100mV over the full military temperature
range. The recommended duty cycle of the input clock is
50% although for clock frequencies below 500kHz the
clock “on” time can be as low as 200ns. The maximum
clock frequency for ±5V supplies is 4MHz. For ±7V sup-
plies and above, the maximum clock frequency is 7MHz.
Do not allow the clock levels to exceed the power supplies.
For single supply operation ≥6V use level shifting at Pin 11
with T2L levels (Figure 4).
AGND (Pins 3, 5): For dual supply operation these pins
should be connected to a ground plane. For single supply
operation both pins should be tied to one half supply,
(Figure 3).
V+, V– (Pins 4, 12): Should be bypassed with a 0.1µF
capacitortoanadequateAGND. Lownoise, nonswitching
powersuppliesarerecommended.Toavoidlatchupwhen
the power supplies exhibit high turn-on transients, a
1N5817 Schottky diode should be added from the V+ and
V– pins to ground (Figures 1, 2 and 3).
10642fa
7
LTC1064-2
U
TYPICAL APPLICATIO S
POWER SOURCE
1
2
3
4
5
6
7
1
2
3
4
5
6
7
14
13
12
11
10
9
14
13
12
11
10
9
OUT C
+
–
V
V
NC
OUT C
NC
NC
NC
V
V
IN
IN
LTC1064-2
LTC1064-2
–
–
–
V
V
V
AGND
AGND
0.1µF
0.1µF
1N5817
+
+
+
f
f
V
V
V
CLK
CLK
0.1µF
20k
0.1µF
1N5817
0.1µF
+
–
50/100
V /V
50/100
AGND
NC
AGND
NC
20k
V
V
OUT
–
+
OUT
8
0.1µF
8
8
R
A
V
IN
LT1006
OUT
R
IN
A
NC
NC
750Ω
1064-2 F02
4
RECOMMENDED OP AMPS:
LT1022, LT318, LT1056
1064-2 F01
0.1µF
Figure 2. Using Schottky Diodes to Protect the
IC from Transient Supply Reversal.
Figure 1. Buffering the Filter Output. The Buffer Op Amp
Should Not Share the LTC1064-2 Power Lines.
1
2
3
4
5
6
7
14
OUT C
NC
13
12
11
10
9
NC
V
IN
LTC1064-2
–
V
AGND
+
+
f
V = 15V
V
CLK
0.1µF
50/100
AGND
NC
0V TO 10V
5k
V
OUT
+
V /2
8
0.1µF
5k
NC
R
A
IN
1064-2 F03
Figure 3. Single Supply Operation. If Fast Power Up or Down
Transients are Expected, Use a 1N5817 Schottky Diode Between
Pin 4 and Pin 5. For V+ = 5V, Derive the Mid-Supply Voltage
with a 7.5k Resistor and an LT1004 2.5V Reference.
10642fa
8
LTC1064-2
U
TYPICAL APPLICATIO S
1
2
3
4
5
6
7
14
13
12
11
10
9
OUT C
NC
NC
+
V
V
IN
LTC1064-2
–
V
AGND
2.2k
2
T L
+
+
f
V
V
CLK
LEVEL
1µF
5k
50/100
AGND
NC
5k
RATIO
V
OUT
8
5k
0.1µF
NC
R
A
IN
1064-2 F04
Figure 4. Level Shifting the Input T2L Clock
for Single Supply Operation ≥6V.
1
14
OUT C
NC
20k
2
3
4
5
6
7
13
NC
V
OUT
V
–
IN
V
100pF
LTC1064-2
12
11
10
9
–
V
AGND
0.1µF
+
+
f
V
V
CLK
0.1µF
+
–
15V
LT1056
–15V
50/100
AGND
NC
V /GND/V
10k
10k
V
–
+
OUT
50Ω
8
NC
220pF
R
A
IN
0.027µF
1064-2 F05
Figure 5. Adding an Output Buffer-Filter to Eliminate Any Clock
Feedthrough. Passband ±0.1dB to 50kHz, –3dB at 94kHz.
10642fa
9
LTC1064-2
U
PACKAGE DESCRIPTIO
J Package
14-Lead CERDIP (Narrow 0.300, Hermetic)
(LTC DWG # 05-08-1110)
.785
(19.939)
MAX
.005
(0.127)
MIN
14
13
12
11
10
9
8
.220 – .310
.025
(5.588 – 7.874)
(0.635)
RAD TYP
2
3
4
5
6
1
7
.200
(5.080)
MAX
.300 BSC
(7.62 BSC)
.015 – .060
(0.381 – 1.524)
.008 – .018
(0.203 – 0.457)
0° – 15°
.045 – .065
(1.143 – 1.651)
.100
(2.54)
BSC
.125
(3.175)
MIN
.014 – .026
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE
OR TIN PLATE LEADS
(0.360 – 0.660)
J14 0801
OBSOLETE PACKAGE
10642fa
10
LTC1064-2
U
PACKAGE DESCRIPTIO
N Package
14-Lead PDIP (Narrow 0.300)
(LTC DWG # 05-08-1510)
.770*
(19.558)
MAX
14
13
12
11
10
9
8
7
.255 ± .015*
(6.477 ± 0.381)
1
2
3
5
6
4
.300 – .325
(7.620 – 8.255)
.045 – .065
(1.143 – 1.651)
.130 ± .005
(3.302 ± 0.127)
.020
(0.508)
MIN
.065
(1.651)
TYP
.008 – .015
(0.203 – 0.381)
+.035
.325
.005
(0.125)
MIN
–.015
.120
(3.048)
MIN
.018 ± .003
(0.457 ± 0.076)
.100
(2.54)
BSC
+0.889
8.255
(
)
–0.381
NOTE:
INCHES
MILLIMETERS
N14 1002
1. DIMENSIONS ARE
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
10642fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.
11
LTC1064-2
U
PACKAGE DESCRIPTIO
SW Package
16-Lead Plastic Small Outline (Wide .300 Inch)
(Reference LTC DWG # 05-08-1620)
.050 BSC .045 ±.005
.030 ±.005
.398 – .413
(10.109 – 10.490)
NOTE 4
TYP
15 14
12
10
9
N
16
N
13
11
.325 ±.005
.420
MIN
.394 – .419
(10.007 – 10.643)
NOTE 3
N/2
8
1
2
3
N/2
RECOMMENDED SOLDER PAD LAYOUT
2
3
5
7
1
4
6
.291 – .299
(7.391 – 7.595)
NOTE 4
.037 – .045
(0.940 – 1.143)
.093 – .104
(2.362 – 2.642)
.010 – .029
× 45°
(0.254 – 0.737)
.005
(0.127)
RAD MIN
0° – 8° TYP
.050
(1.270)
BSC
.004 – .012
.009 – .013
(0.102 – 0.305)
NOTE 3
(0.229 – 0.330)
.014 – .019
.016 – .050
(0.356 – 0.482)
TYP
(0.406 – 1.270)
NOTE:
1. DIMENSIONS IN
INCHES
(MILLIMETERS)
S16 (WIDE) 0502
2. DRAWING NOT TO SCALE
3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS
4. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
10642fa
LW/TP 1202 1K REV A • PRINTED IN USA
12 LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
■
■
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
LINEAR TECHNOLOGY CORPORATION 1990
相关型号:
LTC1064-3CN#PBF
LTC1064-3 - Low Noise, High Frequency, 8th Order Linear Phase Lowpass Filter; Package: PDIP; Pins: 14; Temperature Range: 0°C to 70°C
Linear
LTC1064-3CSW#TR
LTC1064-3 - Low Noise, High Frequency, 8th Order Linear Phase Lowpass Filter; Package: SO; Pins: 16; Temperature Range: 0°C to 70°C
Linear
LTC1064-3CSW#TRPBF
LTC1064-3 - Low Noise, High Frequency, 8th Order Linear Phase Lowpass Filter; Package: SO; Pins: 16; Temperature Range: 0°C to 70°C
Linear
©2020 ICPDF网 联系我们和版权申明