LTC1733EMSE#TR [Linear]
暂无描述;型号: | LTC1733EMSE#TR |
厂家: | Linear |
描述: | 暂无描述 电池 |
文件: | 总16页 (文件大小:170K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LTC1733
Monolithic Linear
Lithium-Ion Battery Charger with
Thermal Regulation
U
FEATURES
DESCRIPTIO
The LTC®1733 is a standalone constant-current/
constant-voltage linear charger for lithium-ion batteries
withanon-chippowerMOSFET.Internalthermalfeedback
regulates the charge current to limit die temperature
during high power operation or high ambient temperature
conditions. This feature allows the user to program a high
charge current without risk of damaging the LTC1733 or
the handheld product.
■
Complete Linear Charger for 1-Cell Lithium-Ion
Batteries
■
■
Thermal Regulation Maximizes Charging Rate
without Risk of Overheating*
No External MOSFET, Sense Resistor or Blocking
Diode Required
Up to 1.5A Charge Current
Preset Charge Voltage with 1% Accuracy
Programmable Charge Current with 7% Accuracy
Programmable Charge Termination Timer
Tiny Thermally Enhanced 10-Pin MSOP Package
Charge Current Monitor Useful for Gas Gauging*
C/10 Charge Current Detection Output
Automatic Recharge
■
■
■
■
■
■
■
■
■
■
■
No external current sense resistor is needed and no
blocking diode is required due to the internal MOSFET
architecture. The charge current and charge time can be
set externally with a single resistor and capacitor, respec-
tively. When the input supply (wall adapter) is removed,
the LTC1733 automatically enters a low current sleep
mode, dropping the battery drain current to less than 5µA.
Thermistor Input for Temperature Qualified Charging
AC Present Logic Output
4.1V/4.2V Pin Selectable Output Voltage
The LTC1733 also includes NTC temperature sensing,
C/10 detection circuitry, AC present logic, 4.1V/4.2V pin
selectability and low battery charge conditioning (trickle
charging).
U
APPLICATIO S
■
Cellular Telephones
The LTC1733 is available in a 10-pin thermally enhanced
MSOP package.
■
Handheld Computers
■
Digital Still Cameras
Charging Docks and Cradles
, LTC and LT are registered trademarks of Linear Technology Corporation.
■
*Patent Pending
U
TYPICAL APPLICATIO
Charge Current vs Battery Voltage
Standalone Li-Ion Battery Charger
1200
T
A
= 0°C
CONSTANT
CURRENT
V
= 5V
IN
1000
800
600
400
200
0
T
= 40°C
8
2
A
T
= 25°C
A
SEL
V
I
= 1A
CC
BAT
9
7
CONSTANT
POWER
4.7µF
BAT
4.2V
LTC1733
TIMER
4
1-CELL
Li-Ion
PROG
CONSTANT
VOLTAGE
GND
NTC
6
BATTERY*
1.5k
1%
5
0.1µF
TRICKLE
CHARGE
V
= 5V
IN
1733TA01
θ
= 40°C/W
JA
2.5
3
4
4.5
2
3.5
*AN OUTPUT CAPACITOR MAY BE REQUIRED
DEPENDING ON BATTERY LEAD LENGTH
BATTERY VOLTAGE (V)
1733 TA01b
sn1733 1733fs
1
LTC1733
W W
U W
U
W
U
ABSOLUTE AXI U RATI GS
PACKAGE/ORDER I FOR ATIO
(Note 1)
Input Supply Voltage (VCC) ........................................ 7V
BAT............................................................................ 7V
NTC, SEL, TIMER, PROG ................ –0.3V to VCC + 0.3V
CHRG, FAULT, ACPR ...................................–0.3V to 7V
BAT Short-Circuit Duration ...........................Continuous
BAT Current (Note 2) .............................................. 1.6A
PROG Current (Note 2) ........................................ 1.6mA
Junction Temperature........................................... 125°C
Operating Temperature Range (Note 3) ...–40°C to 85°C
Storage Temperature Range ................. –65°C to 150°C
Lead Temperature (Soldering, 10 sec).................. 300°C
ORDER PART
TOP VIEW
CHRG
1
2
3
4
5
10 ACPR
NUMBER
V
9
8
7
6
BAT
CC
FAULT
TIMER
GND
SEL
PROG
NTC
LTC1733EMSE
MSE EXPOSED PAD PACKAGE
10-LEAD PLASTIC MSOP
TJMAX = 125°C, θJA = 40°C/W (Note 4)
EXPOSED PAD IS GROUND.
(MUST BE SOLDERED TO PCB
FOR MAXIMUM HEAT TRANSFER).
MSE PART MARKING
LTLX
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VCC = 5V
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
V
CC
V
CC
Supply Voltage
Supply Current
●
4.5
6.5
V
CC
I
Charger On; Current Mode; R
= 30k (Note 5)
●
●
1
0.9
3
2
mA
mA
CC
PROG
Shutdown Mode; V
= 3V
PROG
V
BAT
V
BAT
Regulated Output Voltage
SEL = 0V
●
●
4.059
4.158
4.1
4.2
4.141
4.242
V
V
SEL = V
CC
I
Battery Pin Current
R
R
= 3k; Current Mode
= 1k; Current Mode
●
465
1.395
500
1.5
±1
535
1.605
±5
mA
A
µA
µA
BAT
PROG
PROG
Shutdown Mode; V
Sleep Mode V < V
= 3V
PROG
or V < (V – ∆V )
±1
±5
CC
BAT
CC
UV
UV
I
Trickle Charge Current
V
V
< 2V; R
Rising
= 3k
PROG
●
●
35
50
2.48
100
4.2
65
mA
V
TRIKL
BAT
BAT
V
Trickle Charge Trip Threshold
Trickle Charge Trip Hysteresis
TRIKL
∆V
mV
V
TRIKL
UV
V
V
CC
V
CC
Undervoltage Lockout Voltage
Undervoltage Lockout Hysteresis
V
CC
Rising
4.5
UV
∆V
150
2.15
100
mV
V
V
V
V
Manual Shutdown Threshold Voltage
Manual Shutdown Hysteresis Voltage
PROG Pin Voltage Rising
MSD
mV
MSD-HYS
ASD
Automatic Shutdown Threshold Voltage (V - V ) Voltage Falling
30
60
mV
mV
CC
BAT
(V - V ) Voltage Rising
CC
BAT
sn1733 1733fs
2
LTC1733
ELECTRICAL CHARACTERISTICS
TA = 25°C. VCC = 5V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS MIN
TYP
1.5
MAX
UNITS
V
V
PROG Pin Voltage
R
= 3k, I
= 1V
= 500µA; Current Mode
PROG
PROG
CHRG
PROG
CHRG
CHRG
I
CHRG Pin Weak Pulldown Current
CHRG Pin Output Low Voltage
ACPR Pin Output Low Voltage
FAULT Pin Output Low Voltage
End of Charge Indication Current Level
TIMER Accuracy
V
25
µA
V
V
V
V
I
I
I
= 5mA
0.35
0.35
0.35
50
CHRG
ACPR
FAULT
C/10
= 5mA
= 5mA
V
ACPR
V
FAULT
I
t
R
PROG
= 3k
35
65
mA
%
C
= 0.1µF
±10
TIMER
TIMER
V
Recharge Battery Voltage Threshold
Battery Voltage Falling, SEL = 0V
Battery Voltage Falling, SEL = 5V
3.9
4.0
V
V
RECHRG
V
V
V
V
V
V
V
V
NTC Pin Hot Threshold Voltage
NTC Pin Hot Hysteresis Voltage
NTC Pin Cold Threshold Voltage
NTC Pin Cold Hystersis Voltage
NTC Pin Disable Threshold Voltage
NTC Pin Disable Hystersis Voltage
SEL Pin Threshold Input Low
SEL Pin Threshold Input High
V
V
V
Falling
Rising
Rising
2.5
70
V
mV
V
NTC-HOT
HOT-HYS
NTC-COLD
COLD-HYS
NTC-DIS
DIS-HYS
SEL-IL
NTC
NTC
NTC
4.375
70
mV
mV
mV
V
100
10
0.3
1
V
SEL-IH
T
Junction Temperature in
Constant-Temperature Mode
105
375
°C
LIM
R
Power MOSFET “ON” Resistance
mΩ
ON
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
temperature range are assured by design, characterization and correlation
with statistical process controls.
Note 2: The Absolute Maximum BAT Current Rating of 1.6A is guaranteed
by design and current density calculations. The Absolute Maximum PROG
Current Rating is guaranteed to be 1/1000 of BAT current rating by design.
Note 4: Failure to solder the exposed backside of the package to the PC
board will result in a thermal resistance much higher than 40°C/W.
Note 5: Supply current includes PROG pin current but does not include
Note 3: The LTC1733E is guaranteed to meet performance specifications
from 0°C to 70°C. Specifications over the –40°C to 85°C operating
any current delivered to the battery through the BAT pin.
sn1733 1733fs
3
LTC1733
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Battery Regulation Voltage vs
Battery Charge Current
Battery Regulation Voltage vs
Temperature
Battery Regulation Voltage vs VCC
4.24
4.22
4.20
4.18
4.16
4.14
4.12
4.10
4.08
4.06
4.24
4.22
4.20
4.18
4.16
4.14
4.12
4.10
4.08
4.06
4.24
4.22
4.20
4.18
4.16
4.14
4.12
4.10
4.08
4.06
V
T
= 5V
T
= 25°C
A
V
I
= 5V
CC
A
R
CC
BAT
R
= 25°C
I
= 10mA
= 1.5k
= 10mA
= 1.5k
BAT
R
PROG
V
SEL
= 5V
V
SEL
= 5V
V
SEL
= V
CC
= 1.5k
PROG
PROG
V
SEL
= 0V
V
SEL
= 0V
V
= 0V
SEL
6.0
400
I
5.5
(V)
0
100 200 300
500 600 700 800 900 1000
(mA)
25
TEMPERATURE(°C)
4.0
4.5
5.0
6.5
7.0
–50 –25
0
50
75 100 125
V
BAT
CC
1733 G01
1733 G03
1733 G02
PROG Pin Voltage vs Charge
Current
Charge Current vs Battery Voltage
Charge Current vs Input Voltage
1100
1000
900
800
700
600
500
400
300
200
100
0
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
1100
1000
900
800
700
600
500
400
300
200
100
0
V
T
= 5V
V
T
= 5V
CC
A
CC
A
= 25°C
= 25°C
R
V
= 1.5k
R
V
= 1.5k
PROG
PROG
= 5V
= 5V
SEL
SEL
V
T
= 4.1V
BAT
A
R
= 25°C
= 1.5k
PROG
V
= 5V
SEL
4.0
4.5
5.0
5.5
(V)
6.0
6.5
7.0
400
0
0.5 1.0 1.5
2.5
(V)
3.5 4.0 4.5
3.0
0
100 200 300
500 600 700 800 900 1000
2.0
V
V
CHARGE CURRENT (mA)
CC
BAT
1733 G06
1733 G04
1733 G05
Charge Current vs Temperature
with Thermal Regulation
Charge Current vs Temperature
Charge Current vs VCC
1100
1000
900
800
700
600
500
400
535
530
525
520
515
510
505
500
495
490
485
480
475
470
465
1000
900
800
700
600
500
400
300
200
100
0
V
V
= 5V
CC
R
= 1.5k
PROG
= 4V
BAT
PROG
R
= 3k
V
= 5V
SEL
V
T
= 3.5V
BAT
A
SEL
THERMAL CONTROL
LOOP IN OPERATION
= 25°C
V
= V
CC
V
V
= 5V
CC
R
= 3k
PROG
= 3.5V
BAT
PROG
R
= 1.5k
V
= 5V
SEL
50
TEMPERATURE (°C)
100
4.0
4.5
5.0
5.5
6.0
6.5
7.0
–50
–25
0
25
75
–50
–25
0
25
50
75
100
V
(V)
TEMPERATURE (°C)
CC
1733 G07
1733 G09
1733 G08
sn1733 1733fs
4
LTC1733
U W
TYPICAL PERFOR A CE CHARACTERISTICS
PROG Pin Voltage vs VCC
Constant Current Mode
PROG Pin Voltage vs Temperature
Constant Current Mode
Trickle Charge Current vs
Temperature
1.515
1.510
1.505
1.500
1.495
1.490
1.485
130
120
110
100
90
1.515
1.510
1.505
1.500
1.495
1.490
1.485
T
= 25°C
V
V
= 5V
= 2V
V
V
= 5V
= 4V
A
CC
BAT
PROG
CC
BAT
V
= 3.5V
BAT
PROG
SEL
R
V
= 3k
R
V
= 1.5k
R
V
= 3k
PROG
= 5V
= 5V
= 5V
SEL
SEL
80
70
6.0
7.0
4.0
4.5
5.0
5.5
(V)
6.5
50
TEMPERATURE (°C)
100
50
TEMPERATURE (°C)
100
–50
–25
0
25
75
–50
–25
0
25
75
V
CC
1733 G10
1733 G12
1733 G11
Trickle Charge Current vs VCC
Timer Accuracy vs VCC
Timer Accuracy vs Temperature
13
12
11
10
9
105
104
103
102
101
100
99
105
104
103
102
101
100
99
T
= 25°C
BAT
V
I
= 5V
CC
BAT
V
SEL
T
I
V
C
= 25°C
A
A
V
= 2V
= 0mA
= 5V
= 0mA
= 5V
= 0.1µF
BAT
SEL
R
V
= 1.5k
PROG
SEL
= 5V
C
= 0.1µF
TIMER
TIMER
98
98
97
97
8
96
96
7
4.0
95
95
6.0
7.0
4.5
5.0
5.5
(V)
6.5
25
TEMPERATURE(°C)
–50 –25
0
50
75 100 125
6.0
7.0
4.0
4.5
5.0
5.5
(V)
6.5
V
V
CC
CC
1733 G13
1733 G14
1733 G15
sn1733 1733fs
5
LTC1733
U
U
U
PI FU CTIO S
CHRG: Open-Drain Charge Status Output. When the
battery is being charged, the CHRG pin is pulled low by an
internal N-channel MOSFET. When the charge current
drops to 10% of the full-scale current, the N-channel
MOSFET latches off and a 25µA current source is con-
nected from the CHRG pin to ground. The C/10 latch can
be cleared by momentarily pulling the PROG pin above the
2.15V shutdown threshold, or by toggling VCC. When the
timer runs out or the input supply is removed, the current
source is disconnected and the CHRG pin is forced to a
high impedance state.
GND: Ground. Connect exposed back package to ground.
NTC: Input to the NTC (Negative Temperature Coefficient)
Thermistor Temperature Monitoring Circuit. With an ex-
ternal 10kΩ NTC thermistor to ground and a 1% resistor
to VCC, this pin can sense the temperature of the battery
pack and stop charging when it is out of range. When the
voltage at this pin drops below (0.5)•(VCC) at hot tempera-
tures or rises above (0.875)•(VCC) at cold, charging is
suspended and the internal timer is frozen. The CHRG pin
output status is not affected in this hold state. The FAULT
pinispulledtoground,butnotlatched.Whenthetempera-
ture returns to an acceptable range, charging will resume
and the FAULT pin is released. The NTC feature can be
disabled by grounding the NTC pin.
VCC: Positive Input Supply Voltage. When VCC is within
30mV of VBAT or less than the undervoltage lockout
threshold, the LTC1733 enters sleep mode, dropping IBAT
to less than 5µA. VCC can range from 4.5V to 6.5V. Bypass
this pin with at least a 4.7µF ceramic capacitor to ground.
PROG: Charge Current Program, Shutdown Input and
Charge Current Monitor Pin. The charge current is pro-
grammed by connecting a resistor, RPROG to ground.
When in constant-current mode, the LTC1733 servos the
PROG pin voltage to 1.5V. In all modes the voltage on the
PROG pin can be used to measure the charge current as
follows:
FAULT:Open-DrainFaultStatusOutput. TheFAULTopen-
drain logic signal indicates that the charger has timed out
undertricklechargeconditions(1/4oftotaltimeperiod)or
the NTC comparator is indicating an out-of-range battery
temperature condition. When VBAT is less that 2.48V,
trickle charging activates whereby the charge current
drops to one tenth of its programmed value and the timer
period is reduced by a factor of four. When one fourth of
the timing period has elapsed, if VBAT is still less than
2.48V, trickle charging stops and the FAULT pin latches to
ground. The fault can be cleared by toggling VCC, momen-
tarily pulling the PROG pin above the 2.15V shutdown
threshold, or pulling the BAT pin above 2.48V. If the NTC
comparatorisindicatinganout-of-rangebatterytempera-
ture condition, then the FAULT pin will pull to ground until
the temperature returns to the acceptable range.
ICHG = (VPROG/RPROG) • 1000.
The IC can be forced into shutdown by pulling the PROG
pin above the 2.15V shutdown threshold voltage (note: it
will not be pulled up when allowed to float).
SEL: 4.1V/4.2V Battery Selection Input. Grounding this
pin sets the battery float voltage to 4.1V, while connecting
to VCC sets the voltage to 4.2V.
BAT: ChargeCurrentOutput. Abypasscapacitorofatleast
1µFwitha1Ωseriesresistorisrequiredtominimizeripple
voltage when the battery is not present. A precision
internal resistor divider sets the final float potential on this
pin. The internal resistor divider is disconnected in sleep
and shutdown modes.
TIMER:TimerCapacitor. Thetimerperiodissetbyplacing
a capacitor, CTIMER, to ground. The timer period is:
Time (Hours) = (CTIMER • 3 hr)/(0.1µF)
ACPR: Open-Drain Power Supply Status Output. When
VCC is greater than the undervoltage lockout threshold
and at least 30mV above VBAT, the ACPR pin will pull to
ground. Otherwise, the pin is forced to a high impedance
state.
ShorttheTIMERpintogroundtodisabletheinternaltimer
function.
sn1733 1733fs
6
LTC1733
W
W
SI PLIFIED BLOCK DIAGRA
V
CC
2
105°C
–
D1
TA
D2
D3
T
+
DIE
M2
×1
M1
×1000
+
–
MA
BAT
9
30µA
R1
R2
NTC
6
NTC
MP
+
–
VA
CA
+
–
2.485V
R4
REF
HOT COLD DISABLE
–
+
1
CHRG
C1
SHDN
STOP
2.15V
1.5V
R3
8
SEL
C/10
R5
R6
R7
2.5µA
25µA
LOGIC
10
3
ACPR
ACPR
0.15V
+
–
C2
FAULT
FAULT
CHARGE
COUNTER
OSCILLATOR
4
C3
+
–
2.485V
TO BAT
7
5
1733 F01
PROG
GND
TIMER
R
PROG
C
TIMER
Figure 1.
sn1733 1733fs
7
LTC1733
U
OPERATIO
TheLTC1733isalinearbatterychargerdesignedprimarily
for charging single cell lithium-ion batteries. Featuring an
internal P-channel power MOSFET, the charger uses a
constant-current/constant-voltage charge algorithm with
programmable current and a programmable timer for
charge termination. Charge current can be programmed
up to 1.5A with a final float voltage accuracy of ±1%. No
blocking diode or sense resistor is required thus dropping
the external component count to three for the basic
charger circuit. The CHRG, ACPR, and FAULT open-drain
status outputs provide information regarding the status of
the LTC1733 at all times. An NTC thermistor input
provides the option of charge qualification using battery
temperature.
into the fast charge constant-current mode once the
voltage on the BAT pin rises above 2.48V. In constant-
current mode, the charge current is set by RPROG
.
When the battery approaches the final float voltage, the
chargecurrentbeginstodecreaseastheLTC1733switches
toconstant-voltagemode.Whenthecurrentdropsto10%
of the full-scale charge current, an internal comparator
latches off the MOSFET at the CHRG pin and connects a
weak current source to ground to indicate a near end-of-
charge (C/10) condition. The C/10 latch can be cleared by
momentarily pulling the PROG pin above the 2.15V
shutdown threshold, or momentarily removing and reap-
plying VCC.
An external capacitor on the TIMER pin sets the total
charge time. When this time elapses the charge cycle
terminates and the CHRG pin assumes a high impedance
state. To restart the charge cycle, simply remove the input
voltage and reapply it, or force the PROG pin above the
2.15Vshutdownthreshold(note:simplyfloatingthePROG
pin will not restart the charging cycle.
An internal thermal limit reduces the programmed charge
current if the die temperature attempts to rise above a
presetvalueofapproximately105°C. Thisfeatureprotects
the LTC1733 from excessive temperature, and allows the
user to push the limits of the power handling capability of
agivencircuitboardwithoutriskofdamagingtheLTC1733
ortheexternalcomponents.AnotherbenefitoftheLTC1733
thermal limit is that charge current can be set according to
typical, not worst-case, ambient temperatures for a given
application with the assurance that the charger will auto-
matically reduce the current in worst-case conditions.
For lithium-ion and similar batteries that require accurate
final float potential, the internal reference, voltage ampli-
fier and the resistor divider provide regulation with ±1%
(max) accuracy.
When the input voltage is not present, the charger goes
into a sleep mode, dropping battery drain current, IBAT, to
lessthan5µA.Thisgreatlyreducesthecurrentdrainonthe
batteryandincreasesthestandbytime.Thechargercanbe
shut down (ICC = 0.9mA) by forcing the PROG pin above
2.15V.
The charge cycle begins when the voltage at the VCC pin
rises above the UVLO level and a program resistor is
connected from the PROG pin to ground. At the beginning
of the charge cycle, if the battery voltage is below 2.48V,
the charger goes into trickle charge mode to bring the cell
voltage up to a safe level for charging. The charger goes
sn1733 1733fs
8
LTC1733
U
W U U
APPLICATIO S I FOR ATIO
Undervoltage Lockout (UVLO)
recharge comparator is disabled and a new charge cycle
willnotbeginunlesstheinputvoltageistoggled,thePROG
pin is pulled above the 2.15V shutdown threshold, or the
BATpinispulledabovethe2.48Vtricklechargethreshold.
Aninternalundervoltagelockoutcircuitmonitorstheinput
voltageandkeepsthechargerinshutdownmodeuntilVCC
risesabovetheundervoltagelockoutthreshold. TheUVLO
circuit has a built-in hysteresis of 150mV. Furthermore, to
protect against reverse current in the power MOSFET, the
UVLO circuit keeps the charger in shutdown mode if VCC
falls to within 30mV of the battery voltage. If the UVLO
comparator is tripped, the charger will not come out of
shutdown until VCC rises 60mV above the battery voltage.
Programming Charge Current
The formula for the battery charge current (see Figure 1)
is:
ICHG = (IPROG) • 1000
= (1.5V / RPROG) • 1000 or
RPROG = 1500/ICHG
Trickle Charge and Defective Battery Detection
At the beginning of a charge cycle, if the battery voltage is
low (below 2.48V) the charger goes into trickle charge
reducing the charge current to 10% of the full-scale
current. If the low battery voltage persists for one quarter
of the total charge time, the battery is assumed to be
defective, the charge cycle is terminated, the CHRG pin
output assumes a high impedance state, and the FAULT
pin latches low. The fault can be cleared by toggling VCC,
temporarily forcing the PROG pin above 2.15V, or tempo-
rarily forcing the BAT pin voltage above 2.48V.
where RPROG is the total resistance from the PROG pin to
ground. Under trickle charge conditions, this current is
reduced to 10% of the full-scale value.
For example, if 500mA charge current is required,
calculate:
RPROG = 1500/0.5A = 3kΩ
For best stability over temperature and time, 1% metal-
film resistors are recommended.
If the charger is in constant-temperature or constant-
voltage mode, the battery current can be monitored by
measuring the PROG pin voltage as follows:
Shutdown
The LTC1733 can be shutdown (ICC = 0.9mA) by pulling
the PROG pin above the 2.15V shutdown threshold volt-
age. In shutdown the internal linear regulator is turned off,
and the internal timer is reset.
ICHG = (VPROG / RPROG) • 1000
Programming the Timer
The programmable timer is used to terminate the charge
cycle. The timer duration is programmed by an external
capacitor at the TIMER pin. The total charge time is:
Recharge
The LTC1733 has the ability to recharge a battery
assuming that the battery voltage has been charged above
4.05V (SEL = 5V) or 3.95V (SEL = 0V). Once above these
thresholds, a new charge cycle will begin if the battery
voltage drops below 4V (SEL = 5V) or 3.9V (SEL = 0V) due
to either a load on the battery or self-discharge. The
recharge circuit integrates the BAT pin voltage for a few
milliseconds to prevent a transient from restarting the
charge cycle.
Time (Hours) = (3 Hours) • (CTIMER / 0.1µF) or
CTIMER = 0.1µF • Time (Hours)/3 (Hours)
The timer starts when an input voltage greater than the
undervoltage lockout threshold level is applied and the
program resistor is connected to ground. After a time-out
occurs, the charge current stops, and the CHRG output
assumes a high impedance state to indicate that the
charginghasstopped.ConnectingtheTIMERpintoground
disables the timer function.
If the battery voltage remains below 2.48V during trickle
chargefor1/4oftheprogrammedtime, thebatterymaybe
defective and the charge cycle will end. In addition, the
sn1733 1733fs
9
LTC1733
W U U
U
APPLICATIO S I FOR ATIO
+
Open-Drain Status Outputs
V
DD
V
8
The LTC1733 has three open-drain status outputs: ACPR,
CHRG and FAULT. The ACPR pin pulls low when an input
voltage greater than the undervoltage lockout threshold is
applied and goes high impedance when power (VIN < VUV)
is removed. CHRG and FAULT work together to indicate
the status of the charge cycle. Table 1 describes the status
of the charge cycle based on the CHRG and FAULT
outputs.
V
CC
400k
µPROCESSOR
LTC1733
2k
3
OUT
IN
CHRG
1733 F02
Figure 2. Microprocessor Interface
Table 1.
FAULT
CHRG
Description
When the LTC1733 is in charge mode, the CHRG pin is
pulled low by the internal N-channel MOSFET. To detect
this mode, force the digital output pin, OUT, high and
measure the voltage at the CHRG pin. The N-channel
MOSFET will pull the pin low even with the 2k pull-up
resistor. Once the charge current drops to 10% of the full-
scale current (C/10), the N-channel MOSFET is turned off
and a 25µA current source is connected to the CHRG pin.
The IN pin will then be pulled high by the 2k pull-up. By
forcing the OUT pin to a high impedance state, the current
source will pull the pin low through the 400k resistor.
When the internal timer has expired, the CHRG pin will
assume a high impedance state and the 400k resistor will
then pull the pin high to indicate that charging has termi-
nated.
High
Low
Charge cycle has started, C/10 has not been
reached and charging is proceeding normally.
Low
Low
Charge cycle has started, C/10 has not been
reached, but the charge current and timer
have been paused due to an NTC out-of-
temperature condition.
High
Low
25µA
C/10 has been reached and charging is
pulldown proceeding normally.
25µA
C/10 has been reached but the charge current
pulldown and timer have paused due to an
NTC out-of-temperature condition.
High
Low
High
High
Normal timeout (charging has terminated).
If FAULT goes low and CHRG goes high
impedance simultaneously, then the LTC1733
has timed out due to a bad cell (V
after one-quarter the programmed charge time).
If CHRG goes high impedance first, then
the LTC1733 has timed out normally (charging
has terminated), but NTC is indicating an out-
of-temperature condition.
<2.48V
BAT
NTC Thermistor
Thebatterytemperatureismeasuredbyplacinganegative
temperature coefficient (NTC) thermistor close to the
batterypack.TheNTCcircuitryisshowninFigure3.Touse
this feature, connect a 10k NTC thermistor between the
NTCpinandgroundandaresistor(RHOT)fromtheNTCpin
to VCC. RHOT should be a 1% resistor with a value equal to
the value of the chosen NTC thermistor at 50°C (this value
is 4.1k for a Vishay NTHS0603N02N1002J thermistor).
The LTC1733 goes into hold mode when the resistance of
the NTC thermistor drops below 4.1k which should be
at 50°C. The hold mode freezes the timer and stops
the charge cycle until the thermistor indicates a return
to a valid temperature. As the temperature drops, the
CHRG Status Output Pin
When the charge cycle starts, the CHRG pin is pulled to
ground by an internal N-channel MOSFET capable of
driving an LED. When the charge current drops to 10% of
the full-scale current (C/10), the N-channel MOSFET is
latched off and a weak 25µA current source to ground is
connected to the CHRG pin. After a time-out occurs, the
pin assumes a high impedance state. By using two differ-
ent value pull-up resistors a microprocessor can detect
three states from this pin (charging, C/10, and time-out).
See Figure 2.
sn1733 1733fs
10
LTC1733
W U U
APPLICATIO S I FOR ATIO
U
resistance of the NTC thermistor rises. The LTC1733 is
designed to go into hold mode when the value of the NTC
thermistor increases to seven times the value of RHOT. For
a Vishay NTHS0603N02N1002J thermistor, this value is
28.2k which corresponds to approximately 0°C. The hot
and cold comparators each have approximately 2°C of
hysteresis to prevent oscillation about the trip point. The
NTC function can be disabled by grounding the NTC pin.
package temperature rather than the battery temperature.
This problem can be eliminated by thermally coupling the
NTC thermistor to the battery and not to the LTC1733.
Furthermore, it is essential that the VCC connection to
RHOT is made according to standard Kelvin sense tech-
niques. Since VCC is a high current path into the LTC1733,
it is essential to minimize voltage drops between the VCC
input pin and the top of RHOT
.
V
CC
NTC Trip Point Errors
7/8 V
–
+
CC
CC
CC
When a 1% resistor is used for RHOT, the major error in
the 50°C trip point is determined by the tolerance of the
NTC thermistor. A typical 10k NTC thermistor has a ±10%
tolerance. By looking up the temperature coefficient of the
thermistor at 50°C, the tolerance error can be calculated
in degrees centigrade. Consider the Vishay
NTHS0603N02N1002J thermistor which has a tempera-
ture coefficient of –3.3%/°C at 50°C. Dividing the toler-
ance by the temperature coefficient, ±10%/(–3.3%/°C) =
±3°C, gives the temperature error of the hot trip point.
R
HOT
1%
TOO COLD
TOO HOT
NTC
1/2 V
R
+
–
NTC
10k
3/160 V
+
–
DISABLE NTC
The cold trip point is a little more complicated because its
error depends on the tolerance of the NTC thermistor and
thedegreetowhichtheratioofitsvalueat0°Canditsvalue
at 50°C varies from 7 to 1. Therefore, the cold trip point
error can be calculated using the tolerance, TOL, the
temperature coefficient of the thermistor at 0°C, TC
(in %/°C), the value of the thermistor at 0°C, RCOLD, and
the value of the thermistor at 50°C, RHOT. The formula is:
LTC1733
1733 F03
Figure 3.
Thermistors
The LTC1733 NTC trip points were designed to work with
thermistors whose resistance-temperature characteris-
tics follow Vishay Dale’s “R-T Curve 2”. The Vishay
NTHS0603N02N1002J is an example of such a ther-
mistor. However, Vishay Dale has many thermistor prod-
uctsthatfollowthe“R-TCurve2”characteristicinavariety
of sizes. Futhermore, any thermistor whose ratio of RCOLD
to RHOT is about 7.0 will also work (Vishay Dale R-T Curve
2 shows a ratio of RCOLD to RHOT of 2.816/0.4086 = 6.9).
1+ TOL RCOLD
•
– 1 •100
7
RHOT
TC
TemperatureError(°C)=
Forexample,theVishayNTHS0603N02N1002Jthermistor
with a tolerance of ±10%, TC of –4.5%/°C, and RCOLD
RHOT of 6.89, has a cold trip point error of:
/
NTC Layout Considerations
1± 0.10
It is important that the NTC thermistor not be in close
thermal contact with the LTC1733. Because the LTC1733
package can reach temperatures in excess of the 50°C trip
point, the NTC function can cause a hysteretic oscillation
which turns the charge current on and off according to the
•6.89 – 1 •100
7
Temperature Error (°C) =
–4.5
= –1.8°C, +2.5°C
sn1733 1733fs
11
LTC1733
W U U
U
APPLICATIO S I FOR ATIO
Ifathermistorwithatolerancelessthan±10%isused, the
trip point errors begin to depend on errors other than
thermistor tolerance including the input offset voltage of
theinternalcomparatorsoftheLTC1733andtheeffectsof
internal voltage drops due to high charging currents.
105°C. As the battery voltage rises, the LTC1733 either
returns to constant-current mode or it enters constant-
voltage mode straight from constant-temperature mode.
Regardless of mode, the voltage at the PROG pin is
proportional to the current being delivered to the battery.
Constant-Current/Constant-Voltage/
Constant-Temperature
Power Dissipation
The conditions that cause the LTC1733 to reduce charge
current due to the thermal protection feedback can be
approximated by considering the power dissipated in the
IC. For high charge currents, the LTC1733 power dissipa-
tion is approximately:
The LTC1733 uses a unique architecture to charge a
battery in a constant-current, constant-voltage, constant-
temperature fashion. Figure 1 shows a simplified block
diagram of the LTC1733. Three of the amplifier feedback
loops shown control the constant-current, CA, constant-
voltage, VA, and constant-temperature, TA modes. A
fourth amplifier feedback loop, MA, is used to increase the
output impedance of the current source pair, M1 and M2
(note that M1 is the internal P-channel power MOSFET). It
ensures that the drain current of M1 is exactly 1000 times
greater than the drain current of M2.
PD = (VCC – VBAT) • IBAT
where PD is the power dissipated, VCC is the input supply
voltage, VBAT is the battery voltage, and IBAT is the battery
charge current. It is not necessary to perform any worst-
case power dissipation scenarios because the LTC1733
will automatically reduce the charge current to maintain
the die temperature at approximately 105°C. However, the
approximate ambient temperature at which the thermal
feedback begins to protect the IC is:
Amplifiers CA, TA, and VA are used in three separate
feedback loops to force the charger into constant-current,
temperature, or voltage mode, respectively. Diodes, D1,
D2, and D3 provide priority to whichever loop is trying to
reduce the charging current the most. The outputs of the
other two amplifiers saturate low which effectively re-
moves their loops from the system. When in constant-
current mode, CA servos the voltage at the PROG pin to be
precisely 1.50V (or 0.15V when in trickle-charge mode).
TA limits the die temperature to approximately 105°C
when in constant-temperature mode and the PROG pin
voltage gives an indication of the charge current as dis-
cussed in “Programming Charge Current” . VA servos its
inverting input to precisely 2.485V when in constant-
voltage mode and the internal resistor divider made up of
R1 and R2 ensures that the battery voltage is maintained
at either 4.1V or 4.2V. Again, the PROG pin voltage gives
an indication of the charge current.
TA = 105°C – PDθJA
TA = 105°C – (VCC – VBAT) • IBAT • θJA
Example: Consider an LTC1733 operating from a 5V wall
adapter providing 1.2A to a 3.75V Li-Ion battery. The
ambient temperature above which the LTC1733 will begin
to reduce the 1.2A charge current is approximately:
TA = 105°C – (5V – 3.75V) • 1.2A • 40°C/W
TA = 105°C – 1.5W • 40°C/W = 105°C – 60°C = 45°C
The LTC1733 can be used above 45°C, but the charge
current will be reduced below 1.2A. The approximate
charge current at a given ambient temperature can be
approximated by:
105°C – TA
(VCC – VBAT )•θJA
In typical operation, the charge cycle begins in constant-
current mode with the current delivered to the battery
equal to 1500V/RPROG. If the power dissipation of the
LTC1733 results in the junction temperature approaching
105°C, the amplifier (TA) will begin decreasing the charge
current to limit the die temperature to approximately
IBAT
=
Consider the above example with an ambient temperature
of 55°C. The charge current will be reduced to approxi-
mately:
sn1733 1733fs
12
LTC1733
W U U
APPLICATIO S I FOR ATIO
U
Stability
105°C – 55°C
(5V – 3.75V)•40°C / W 50°C /A
50°C
IBAT
=
=
= 1A
The constant-voltage mode feedback loop is stable
without any compensation when a battery is connected.
However, a 1µF capacitor with a 1Ω series resistor to GND
is recommended at the BAT pin to keep ripple voltage low
when the battery is disconnected.
Furthermore, the voltage at the PROG pin will change
proportionally with the charge current as discussed in the
Programming Charge Current section.
It is important to remember that LTC1733 applications do
notneedtobedesignedforworst-casethermalconditions
since the IC will automatically reduce power dissipation
when the junction temperature reaches approximately
105°C. See Design Note 283 for additional information.
In the constant-current mode it is the PROG pin that is in
the feedback loop and not the battery. The constant-
current mode stability is affected by the impedance at the
PROG pin. With no additional capacitance on the PROG
pin, stability is acceptable with program resistor values as
high as 50k. However, additional capacitance on this node
reduces the maximum allowed program resistor. The pole
frequency at the PROG pin should be kept above 500kHz.
Therefore, if the PROG pin is loaded with a capacitance, C,
the following equation should be used to calculate the
Board Layout Considerations
In order to be able to deliver maximum charge current
under all conditions, it is critical that the exposed pad on
the backside of the LTC1733 package is soldered to the
board. Correctly soldered to a 2500mm2 double-sided
1oz. copper board the LTC1733 has a thermal resistance
of approximately 40°C/W. Failure to make thermal contact
between the exposed pad on the backside of the package
and the copper board will result in thermal resistances far
greater than 40°C/W. As an example, a correctly soldered
LTC1733 can deliver over 1250mA to a battery from a 5V
supply at room temperature. Without a backside thermal
connection, this number could drop to less than 500mA.
maximum resistance value for RPROG
:
RPROG < 1/(6.283 • 500E3 • C)
Average, rather than instantaneous, battery current may
beofinteresttotheuser.Forexample,ifaswitchingpower
supply operating in low-current mode is connected in
parallel with the battery the average current being pulled
out of the BAT pin is typically of more interest than the
instantaneous current pulses. In such a case, a simple RC
filter can be used on the PROG pin to measure the average
battery current as shown in Figure 4. A 10k resistor is
added between the PROG pin and the filter capacitor and
monitoring circuit to ensure stability.
VCC Bypass Capacitor
Many types of capacitors can be used for input bypassing.
However, caution must be exercised when using multi-
layer ceramic capacitors. Because of the self resonant and
high Q characteristics of some types of ceramic capaci-
tors, high voltage transients can be generated under some
start-up conditions, such as connecting the charger input
to a hot power source. For more information refer to
Application Note 88.
LTC1733
CHARGE
10k
7
CURRENT
MONITOR
CIRCUITRY
PROG
GND
R
PROG
C
FILTER
5
1733 F04
Figure 4. Isolating Capacitive Load on PROG Pin and Filtering.
sn1733 1733fs
13
LTC1733
U
TYPICAL APPLICATIO
Basic Li-Ion Battery Charger with Reverse Polarity Input Protection
I
= 1A
BAT
LTC1733
9
7
2
8
5V WALL
ADAPTER
V
BAT
CC
SEL
+
4.2V Li-Ion
BATTERY
4.7µF
4
TIMER
PROG
GND
5
NTC
6
1.5k
1%
0.1µF
1733 F06
sn1733 1733fs
14
LTC1733
U
PACKAGE DESCRIPTIO
MSE Package
10-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1663)
BOTTOM VIEW OF
EXPOSED PAD OPTION
2.06 ± 0.102
(.081 ± .004)
2.794 ± 0.102
(.110 ± .004)
0.889 ± 0.127
(.035 ± .005)
1
1.83 ± 0.102
(.072 ± .004)
5.23
(.206)
MIN
2.083 ± 0.102 3.2 – 3.45
(.082 ± .004) (.126 – .136)
10
0.50
(.0197)
BSC
0.305 ± 0.038
(.0120 ± .0015)
TYP
3.00 ± 0.102
(.118 ± .004)
(NOTE 3)
0.497 ± 0.076
(.0196 ± .003)
REF
10 9
8
7 6
RECOMMENDED SOLDER PAD LAYOUT
3.00 ± 0.102
(.118 ± .004)
NOTE 4
4.88 ± 0.10
(.192 ± .004)
DETAIL “A”
0.254
(.010)
0° – 6° TYP
1
2
3
4 5
GAUGE PLANE
0.53 ± 0.01
(.021 ± .006)
0.86
(.034)
REF
1.10
(.043)
MAX
DETAIL “A”
0.18
(.007)
SEATING
PLANE
0.17 – 0.27
(.007 – .011)
0.13 ± 0.05
(.005 ± .002)
MSOP (MSE) 1001
0.50
(.0197)
TYP
NOTE:
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
sn1733 1733fs
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.
15
LTC1733
U
TYPICAL APPLICATIO
Full Featured Single Cell Li-Ion Charger
V
= 5V
IN
1k
1k
8
2
1k
SEL
V
CC
10
3
4k
ACPR
FAULT
BAT
1%
1
6
4
CHRG
I
= 500mA
4.7µF
LTC1733
NTC
BAT
9
1µF
7
TIMER
PROG
+
R
4.2V Li-Ion
BATTERY
NTC
10k
GND
3k
1%
1Ω
5
0.1µF
1733 F05
RELATED PARTS
PART NUMBER
DESCRIPTION
200kHz/500kHz Switching Battery Charger
Lithium-Ion Battery Charger Termination Controllers Time or Charge Current Termination, Preconditioning 8-Lead MSOP
COMMENTS
LT1571
Up to 1.5A Charge Current; Preset and Adjustable Battery Voltages
LTC1729
LTC1730
Lithium-Ion Battery Pulse Charger
No Blocking Diode Required, Current Limit for Maximum Safety
LTC1731
Lithium-Ion Linear Battery Charger Controller
Simple Charger uses External FET, Features Preset Voltages, C/10
Charger Detection and Programmable Timer
LTC1732
Lithium-Ion Linear Battery Charger Controller
Simple Charger uses External FET, Features Preset Voltages, C/10
Charger Detection and Programmable Timer, Input Power Good Indication
LTC1734
LTC1998
LTC4050
Lithium-Ion Linear Battery Charger in ThinSOT
Lithium-Ion Low Battery Detector
Simple ThinSOT Charger, No Blocking Diode, No Sense Resistor Needed
1% Accurate 2.5µA Quiescent Current, SOT-23
Lithium-Ion Linear Battery Charger Controller
Simple Charger uses External FET, Features Preset Voltages, C/10
Charger Detection and Programmable Timer, Input Power Good Indication,
Thermistor Interface
sn1733 1733fs
LT/TP 0602 2K • PRINTED IN USA
16 LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
●
●
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
相关型号:
LTC1733EMSE#TRPBF
LTC1733 - Monolithic Linear Lithium-Ion Battery Charger with Thermal Regulation; Package: MSOP; Pins: 10; Temperature Range: -40°C to 85°C
Linear
LTC1734ES6-4.1#TR
LTC1734 - Lithium-Ion Linear Battery Charger in ThinSOT; Package: SOT; Pins: 6; Temperature Range: -40°C to 85°C
Linear
LTC1734ES6-4.1#TRMPBF
LTC1734 - Lithium-Ion Linear Battery Charger in ThinSOT; Package: SOT; Pins: 6; Temperature Range: -40°C to 85°C
Linear
LTC1734ES6-4.1#TRPBF
LTC1734 - Lithium-Ion Linear Battery Charger in ThinSOT; Package: SOT; Pins: 6; Temperature Range: -40°C to 85°C
Linear
LTC1734ES6-4.2#PBF
LTC1734 - Lithium-Ion Linear Battery Charger in ThinSOT; Package: SOT; Pins: 6; Temperature Range: -40°C to 85°C
Linear
LTC1734ES6-4.2#TRM
LTC1734 - Lithium-Ion Linear Battery Charger in ThinSOT; Package: SOT; Pins: 6; Temperature Range: -40°C to 85°C
Linear
LTC1734ES6-4.2#TRMPBF
LTC1734 - Lithium-Ion Linear Battery Charger in ThinSOT; Package: SOT; Pins: 6; Temperature Range: -40°C to 85°C
Linear
©2020 ICPDF网 联系我们和版权申明