LTC3834IGN-1-TRPBF [Linear]
30μA IQ Synchronous Step-Down Controller; 30μA IQ同步降压型控制器
| 型号： | LTC3834IGN-1-TRPBF |
| 厂家： | 
Linear |
| 描述： | 30μA IQ Synchronous Step-Down Controller |
| 文件： | 总28页 (文件大小：291K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LTC3834-1
30μA I Synchronous
Q
Step-Down Controller
U
FEATURES
DESCRIPTIO
TheLTC®3834-1isahighperformancestep-downswitch-
ing regulator controller that drives an all N-channel syn-
chronous power MOSFET stage. A constant-frequency
current mode architecture allows a phase-lockable fre-
quency of up to 650kHz.
■
Wide Output Voltage Range: 0.8V V OUT 10V
■
Low Operating IQ: 30μA
OPTI-LOOP® Compensation Minimizes COUT
1ꢀ Output Voltage Accuracy
Wide VIN Range: 4V to 36V
■
■
■
■
Phase-Lockable Fixed Frequency 140kHz to 650kHz
The 30μA no-load quiescent current extends operating
life in battery powered systems. OPTI-LOOP compen-
sation allows the transient response to be optimized over
a wide range of output capacitance and ESR values. The
LTC3834-1 featuresaprecision0.8Vreference. The4Vto
36V input supply range encompasses a wide range of bat-
tery chemistries.
■
Dual N-Channel MOSFET Synchronous Drive
■
Very Low Dropout Operation: 99% Duty Cycle
■
Adjustable Output Voltage Soft-Start or Tracking
■
Output Current Foldback Limiting
■
Output Overvoltage Protection
■
Low Shutdown IQ: 4μA
■
Selectable Continuous, Pulse-Skipping or
Burst Mode® Operation at Light Loads
The TRACK/SS pin ramps the output voltage during start-
up. Current foldback limits MOSFET heat dissipation
during short-circuit conditions. An enhanced feature set
part (LTC3834) is available.
■
Small 16-Lead Narrow SSOP or 5mm × 3mm
DFN Package
U
Comparison of LTC3834 and LTC3834-1
CLKOUT/
APPLICATIO S
■
Automotive Systems
PART #
PHASMD
EXTV
PGOOD
PACKAGES
CC
■
Telecom Systems
LTC3834
LTC3834-1
YES
YES
NO
YES
FE20/4 × 5 QFN
GN16/3 × 5 DFN
■
Battery-Operated Digital Devices
Distributed DC Power Systems
NO
NO
■
, LT, LTC, LTM, Burst Mode, PolyPhase and OPTI-LOOP are registered trademarks of
Linear Technology Corporation. All other trademarks are the property of their respective
owners. Protected by U.S. Patents, including 5408150, 5481178, 5705919, 5929620,
6304066, 6498466, 6580258, 6611131.
U
TYPICAL APPLICATIO
Efficiency and Power Loss
vs Load Current
High Efficiency Step-Down Converter
10000
1000
100
10
100
90
PLLLPF
V
IN
V
IN
4V TO 36V
10μF
RUN
TG
0.01μF
80
0.22μF
TRACK/SS
70
BOOST
SW
3.3μH
V
OUT
0.012Ω
I
TH
3.3V
5A
60
50
560pF
54.2k
LTC3834-1
150pF
40
30
20
10
SGND
PLLIN/MODE
INTV
CC
150μF
4.7μF
68.1k
V
FB
BG
1
–
+
SENSE
SENSE
215k
PGND
0
0.1
0.000001
0.0001
0.01
1
OUTPUT CURRENT (A)
38341 TA01
38341 TA01b
38341f
1
LTC3834-1
W W U W
ABSOLUTE AXI U RATI GS
(Note 1)
Input Supply Voltage (VIN).........................36V to –0.3V Peak Output Current <10μs (TG, BG)......................... 3A
Top Side Driver Voltage (BOOST) ..............42V to –0.3V INTVCC Peak Output Current ................................ 50mA
Switch Voltage (SW) ....................................36V to –5V Operating Temperature Range (Note 2) .. –40°C to 85°C
INTVCC, (BOOST-SW).................................8.5V to –0.3V Junction Temperature (Note 3)............................. 125°C
RUN, TRACK/SS ......................................... 7V to –0.3V Storage Temperature Range ................. –65°C to 150°C
SENSE+, SENSE– Voltages.........................11V to –0.3V Lead Temperature
PLLIN/MODE, PLLLPF ......................... INTVCC to –0.3V
TH, VFB Voltages .......................................2.7V to –0.3V
(GN Package, Soldering, 10 sec) ...................... 300°C
I
U
U
U
PI CO FIGURATIO
TOP VIEW
TOP VIEW
PLLLPF
1
2
3
4
5
6
7
8
16 PLLIN/MODE
PLLLPF
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
PLLIN/MODE
+
+
I
TH
15 SENSE
I
TH
SENSE
–
–
TRACK/SS
14 SENSE
TRACK/SS
SENSE
V
FB
13 RUN
12 BOOST
11 TG
V
FB
RUN
BOOST
TG
17
SGND
PGND
BG
SGND
PGND
BG
10 SW
SW
INTV
CC
9
V
IN
INTV
CC
V
IN
GN PACKAGE
16-LEAD PLASTIC SSOP
DHC PACKAGE
16-Pin (5mm × 3mm) PLASTIC DFN
TJMAX = 150°C, θJA = 90°C/W
TJMAX = 125°C, θJA = 43.5°C/W
EXPOSED PAD (PIN 17) IS SGND
MUST BE SOLDERED TO PCB
U
W
U
ORDER I FOR ATIO
LEAD FREE FINISH
LTC3834EDHC-1#PBF
LTC3834IDHC-1#PBF
LTC3834EGN-1#PBF
LTC3834IGN-1#PBF
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
–40°C to 85°C (Note 2)
–40°C to 85°C
–40°C to 85°C (Note 2)
–40°C to 85°C
LTC3834EDHC-1#TRPBF
LTC3834IDHC-1#TRPBF
LTC3834EGN-1#TRPBF
LTC3834IGN-1#TRPBF
38341
38341
38341
38341
16-Lead (5mm × 3mm) Plastic DFN
16-Lead (5mm × 3mm) Plastic DFN
16-Lead Plastic SSOP
16-Lead Plastic SSOP
Consult LTC Marketing for parts specified with wider operating temperature ranges. *Temperature grades are identified by a label on the shipping container.
Consult LTC Marketing for information on nonstandard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 12V, VRUN = 5V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Main Control Loop
V
Regulated Feedback Voltage
Feedback Current
(Note 4); I Voltage = 1.2V
●
0.792
0.800
–5
0.808
–50
V
nA
FB
TH
I
(Note 4)
VFB
V
Reference Voltage Line Regulation
V
IN
= 4V to 30V (Note 4)
0.002
0.02
%/V
38341f
REFLNREG
2
LTC3834-1
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. VIN = 12V, VRUN = 5V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
V
Output Voltage Load Regulation
(Note 4)
LOADREG
Measured in Servo Loop; I Voltage = 1.2V to 0.7V
●
●
0.1
–0.1
0.5
–0.5
%
%
TH
Measured in Servo Loop; I Voltage = 1.2V to 2V
TH
g
Transconductance Amplifier g
I
= 1.2V; Sink/Source 5μA (Note 4)
TH
0.5
mmho
m
m
I
Input DC Supply Current
Sleep Mode
(Note 5)
Q
RUN = 5V, V = 0.83V (No Load)
30
4
50
10
μA
μA
FB
Shutdown
V
V
= 0V
RUN
UVLO
Undervoltage Lockout
Ramping Down
●
3.7
10
4
V
%
IN
V
Feedback Overvoltage Lockout
Sense Pins Total Source Current
Maximum Duty Factor
Measured at V Relative to Regulated V
8
12
OVL
FB
FB
I
V
– = V + = 0V
SENSE SENSE
–220
99.4
1.1
μA
%
SENSE
DF
In Dropout
98
0.85
0.5
85
MAX
I
Soft-Start Charge Current
V
V
V
= 0V
TRACK
1.45
0.9
μA
V
TRACK/SS
V
V
ON
RUN Pin ON Threshold
V Rising
RUN1, RUN2
0.7
RUN
Maximum Current Sense Threshold
= 0.7V, V
– = 3.3V
SENSE
●
100
115
mV
SENSE(MAX)
FB
TG Transition Time:
Rise Time
Fall Time
(Note 6)
TG1, 2 t
TG1, 2 t
C
C
= 3300pF
50
50
90
90
ns
ns
r
f
LOAD
= 3300pF
LOAD
BG Transition Time:
Rise Time
Fall Time
(Note 6)
LOAD
LOAD
BG1, 2 t
BG1, 2 t
C
C
= 3300pF
= 3300pF
40
40
90
80
ns
ns
r
f
TG/BG t
Top Gate Off to Bottom Gate On Delay C
Synchronous Switch-On Delay Time
= 3300pF
70
ns
ns
ns
1D
LOAD
LOAD
BG/TG t
Bottom Gate Off to Top Gate On Delay C
Top Switch-On Delay Time
= 3300pF
70
2D
t
Minimum On-Time
(Note 7)
200
ON(MIN)
CC
INTV Linear Regulator
V
V
Internal V Voltage
8.5V < V < 30V
5.0
5.25
0.2
5.5
1.0
V
INTVCCVIN
LDOVIN
CC
IN
INTV Load Regulation
I
= 0mA to 20mA
CC
%
CC
Oscillator and Phase-Locked Loop
f
f
f
f
f
I
Nominal Frequency
Lowest Frequency
Highest Frequency
V
V
V
= No Connect
= 0V
360
220
475
400
250
530
115
800
440
280
580
140
kHz
kHz
kHz
kHz
kHz
NOM
PLLLPF
PLLLPF
PLLLPF
LOW
= INTV
HIGH
CC
Minimum Synchronizable Frequency PLLIN/MODE = External Clock; V
Maximum Synchronizable Frequency PLLIN/MODE = External Clock; V
Phase Detector Output Current
Sinking Capability
Sourcing Capability
= 0V
= 2V
SYNCMIN
SYNCMAX
PLLLPF
PLLLPF
650
PLLLPF
f
f
< f
> f
–5
5
μA
μA
PLLIN/MODE
PLLIN/MODE
OSC
OSC
Note 4: The LTC3834-1 is tested in a feedback loop that servos V to a
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may
cause permanent damage to the device. Exposure to any Absolute Maximum
Rating condition for extended periods may affect device reliability and lifetime.
Note 2: The LTC3834E-1 is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 85°C operating temperature
range are assured by design, characterization and correlation with statistical
process controls. The LTC3834I-1 is guaranteed to meet performance
specifications over the –40°C to 85°C operating temperature range.
ITH
specified voltage and measures the resultant V
FB.
Note 5: Dynamic supply current is higher due to the gate charge being
delivered at the switching frequency. See Applications Information.
Note 6: Rise and fall times are measured using 10% and 90% levels. Delay
times are measured using 50% levels.
Note 7: The minimum on-time condition is specified for an inductor
peak-to-peak ripple current 40% of I
(see Minimum On-Time
MAX
Note 3: T is calculated from the ambient temperature T and power
Considerations in the Applications Information section).
J
A
dissipation P according to the following formulas:
D
LTC3834GN-1: T = T + (P • 90°C/W)
J
A
D
LTC3834DHC-1: T = T + (P • 43.5°C/W)
J
A
D
38341f
3
LTC3834-1
U W
TYPICAL PERFOR A CE CHARACTERISTICS
TA = 25ºC, unless otherwise noted.
Efficiency and Power Loss vs
Output Current
Efficiency vs Load Current
Efficiency vs Input Voltage
10000
1000
100
10
100
90
100
90
98
96
94
92
90
88
Burst Mode OPERATION
FORCED CONTINUOUS MODE
PULSE SKIPPING MODE
= 12V
= 3.3V
V
V
= 12V
= 5V
IN
IN
V
= 3.3V
OUT
80
V
V
IN
OUT
70
80
60
50
70
40
30
20
10
0
60
50
40
86
84
82
80
1
V
OUT
= 3.3V
FIGURE 10 CIRCUIT
10
FIGURE 10 CIRCUIT
0.01
FIGURE 10 CIRCUIT
0.01
0.1
20 25 30 35 40
INPUT VOLTAGE (V)
0.000001
0.0001
OUTPUT CURRENT (A)
1
0
5
15
0.000001
0.0001
OUTPUT CURRENT (A)
1
38341 G01
38341 G02
38341 G03
Load Step (Forced Continuous
Mode)
Load Step (Burst Mode Operation)
Load Step (Pulse Skipping Mode)
V
V
V
OUT
OUT
OUT
100mV/DIV
AC
100mV/DIV
AC
100mV/DIV
AC
COUPLED
COUPLED
COUPLED
IL
2A/DIV
IL
2A/DIV
IL
2A/DIV
38341 G04
38341 G06
38341 G05
20μs/DIV
20μs/DIV
20μs/DIV
V
= 3.3V
V
= 3.3V
V
= 3.3V
OUT
OUT
OUT
FIGURE 10 CIRCUIT
FIGURE 10 CIRCUIT
FIGURE 10 CIRCUIT
Inductor Current at Light Load
Soft Start-Up
Tracking Start-Up
MASTER
2V/DIV
FORCED
CONTINUOUS
MODE
V
OUT
1V/DIV
V
OUT
2A/DIV
Burst Mode
OPERATION
2V/DIV
PULSE
SKIPPING
MODE
38341 G07
38341 G08
38341 G09
2μs/DIV
20ms/DIV
FIGURE 10 CIRCUIT
20ms/DIV
FIGURE 10 CIRCUIT
V
LOAD
FIGURE 10 CIRCUIT
= 3.3V
OUT
I
= 100μA
38341f
4
LTC3834-1
U W
TYPICAL PERFOR A CE CHARACTERISTICS
TA = 25ºC, unless otherwise noted.
Total Input Supply Current vs
Input Voltage
INTVCC Voltages vs Temperature
INTVCC Line Regulation
350
300
250
200
150
5.5
5.4
5.3
5.2
5.1
5.0
6.0
5.8
5.6
5.4
5.2
5.0
4.8
4.6
FIGURE 10 CIRCUIT
INTV
CC
300μA LOAD
100
50
0
4.4
4.2
4.0
NO LOAD
20
15
INPUT VOLTAGE (V)
30
35
5
10
25
25
10 15 20
INPUT VOLTAGE (V)
35 40
35
75
95
0
5
30
–45 –25 –5
15
55
TEMPERATURE (°C)
38341 G10
38341 G12
38341 G11
Maximum Current Sense Voltage
vs ITH Voltage Cycle
SENSE Pins Total Input Bias
Current
Maximum Current Sense
Threshold vs Duty
100
80
60
30
120
100
80
FORCED CONTINUOUS
Burst Mode OPERATION
(RISING)
Burst Mode OPERATION
(FALLING)
PULSE SKIPPING
0
–30
–60
–90
6O
40
20
0
–120
–150
–180
–210
–240
–270
–300
60
40
20
0
–20
10% DUTY CYCLE
1.0 1.2 1.4
PIN VOLTAGE (V)
–40
0.6
0
0.2 0.4
I
0.8
5
6
7
8
9
10
0
1
2
3
4
40
60 70 80 90 100
50
0
10 20 30
V
COMMON MODE VOLTAGE (V)
DUTY CYCLE (%)
TH
SENSE
38341 G13
38341 G14
38341 G15
Foldback Current Limit
Quiescent Current vs Temperature
120
100
80
40
38
36
34
32
60
40
20
0
30
28
26
24
22
0.4
0.6 0.7 0.8 0.9
0
0.1 0.2 0.3
0.5
30
TEMPERATURE (°C)
60 75 90
–45 –30 –15
0
15
45
FEEDBACK VOLTAGE (V)
38341 G16
38341zz G17
38341f
5
LTC3834-1
U W
TYPICAL PERFOR A CE CHARACTERISTICS
TA = 25ºC, unless otherwise noted.
TRACK/SS Pull-Up Current vs
Temperature
Shutdown (RUN) Threshold vs
Temperature
SENSE Pins Total Input Bias
Current vs ITH
4
1.30
1.00
0.95
0.90
0.85
0.80
0.75
0.70
0.65
0.60
0.55
0.50
1.25
1.20
1.15
1.10
1.05
1.00
0.95
0.90
3
2
1
0
1.0
VOLTAGE (V)
1.4
30
TEMPERATURE (°C)
60 75 90
0
0.2 0.4 0.6 0.8
1.2
–45 –30 –15
0
15
45
30
TEMPERATURE (°C)
–45 –30 –15
0
15
45 60 75 90
I
TH
38341 G18
38341 G19
38341 G20
Regulated Feedback Voltage vs
Temperature
SENSE Pins Total Input Bias
Current vs Temperature
Shutdown Current vs Input
Voltage
60
30
808
806
804
12
10
8
V
= 10V
OUT
0
V
= 3.3V
OUT
–30
–60
–90
802
800
798
796
794
792
–120
–150
–180
–210
–240
–270
–300
6
4
V
= 0V
15
OUT
2
0
30
–45 –30 –15
0
45 60 75 90
30
–45 –30 –15
0
15
45 60 75 90
5
10
15
20
25
35
30
TEMPERATURE (°C)
TEMPERATURE (°C)
INPUT VOLTAGE (V)
38341 G22
38341 G21
38341 G23
Oscillator Frequency vs
Temperature
Undervoltage Lockout Threshold
vs Temperature
4.2
4.1
800
700
600
500
400
300
200
100
0
4.0
3.9
3.8
3.7
3.6
3.5
3.4
3.3
3.2
RISING
V
= INTV
CC
PLLLPF
V
= FLOAT
= GND
PLLLPF
FALLING
V
PLLLPF
30
0
TEMPERATURE (°C)
35
TEMPERATURE (°C)
75
95
–45 –30 –15
15
45 60 75 90
–45 –25 –5
15
55
38341 G25
38341 G24
38341f
6
LTC3834-1
U W
TYPICAL PERFOR A CE CHARACTERISTICS
TA = 25ºC, unless otherwise noted.
INTVCC vs Load Current
Shutdown Current vs Temperature
5.3
7
6
5
4
3
2
1
0
5.2
5.1
5.0
4.9
4.8
4.7
4.6
V
= 12V
IN
30
TEMPERATURE (°C)
60 75 90
40
60
–45 –30 –15
0
15
45
0
10
20
30
50
LOAD CURRENT (mA)
38341 G27
38341 G26
U
U
U
PI FU CTIO S (DHC Package/GN Package)
PLLLPF (Pin 1/Pin 1): The phase-locked loop’s lowpass
filter is tied to this pin when synchronizing to an external
clock. Alternatively, tie this pin to GND, INTVCC or leave
floating to select 250kHz, 530kHz or 400kHz switching
frequency.
BG (Pin 7/Pin 7): High Current Gate Drive for Bottom
(Synchronous) N-Channel MOSFET. Voltage swing at this
pin is from ground to INTVCC.
INTVCC (Pin 8/Pin 8): Output of the Internal Linear Low
Dropout Regulator. The driver and control circuits are
powered from this voltage source. Must be decoupled to
power ground with a minimum of 4.7μF tantalum or
ceramic capacitor.
ITH (Pin 2/Pin 2): Error Amplifier Outputs and Switching
Regulator Compensation Points. The current comparator
trip point increases with this control voltage.
TRACK/SS (Pin 3/Pin 3): External Tracking and Soft-
Start Input. The LTC3834-1 regulates the VFB voltage
to the smaller of 0.8V or the voltage on the TRACK/
SS pin. A internal 1μA pull-up current source is connected
to this pin. A capacitor to ground at this pin sets the
ramp time to final regulated output voltage. Alternatively,
a resistor divider on another voltage supply connected
to this pin allows the LTC3834-1 output to track the
other supply during startup.
VIN (Pin 9/Pin 9): Main Supply Pin. A bypass capacitor
should be tied between this pin and the signal ground pin.
SW (Pin 10/Pin 10): Switch Node Connections to Induc-
tor. Voltage swing at this pin is from a Schottky diode
(external) voltage drop below ground to VIN.
TG (Pin 11/Pin 11): High Current Gate Drive for Top N-
Channel MOSFET. These are the outputs of floating driv-
ers with a voltage swing equal to INTVCC – 0.5V superim-
posed on the switch node voltage SW.
VFB (Pin 4/Pin 4): Receives the remotely sensed feed-
back voltage from an external resistive divider across
the output.
BOOST (Pin 12/Pin 12): Bootstrapped Supply to the Top
Side Floating Driver. A capacitor is connected between the
BOOST and SW pins and a Schottky diode is tied between
the BOOST and INTVCC pins. Voltage swing at the BOOST
pin is from INTVCC to (VIN + INTVCC).
SGND (Pin 5/Pin 5): Small Signal Ground. Must be routed
separately from high current grounds to the common (–)
terminals of the input capacitor.
RUN (Pin 13/Pin 13): Digital Run Control Input for Con-
PGND (Pin 6/Pin 6): Driver Power Ground. Connects to
the source of bottom (synchronous) N-channel MOSFET,
anode of the Schottky rectifier and the (–) terminal of CIN.
troller. Forcing this pin below 0.7V shuts down all control-
38341f
7
LTC3834-1
U
U
U
PI FU CTIO S (DHC Package/GN Package)
ler functions, reducing the quiescent current that the
LTC3834-1 draws to approximately 4μA.
SENSE– (Pin 14/Pin 14): The (–) Input to the Differential
Current Comparator.
SENSE+ (Pin 15/Pin 15): The (+) Input to the Differential
Current Comparator. The ITH pin voltage and controlled
offsets between the SENSE– and SENSE+ pins in conjunc-
tion with RSENSE set the current trip threshold.
phase-locked loop will force the rising TG signal to be
synchronized with the rising edge of the external clock. In
this case, an R-C filter must be connected to the PLLLPF
pin. When not synchronizing to an external clock, this
input determines how the LTC3834-1 operates at light
loads. Pulling this pin below 0.7V selects Burst Mode
operation. Tying this pin to INTVCC forces continuous
inductor current operation. Tying this pin to a voltage
greater than 0.9V and less than INTVCC selects pulse-
skipping operation.
PLLIN/MODE (Pin 16/Pin 16): External Synchronization
Input to Phase Detector and Forced Continuous Control
Input. When an external clock is applied to this pin, the
Exposed Pad (Pin 17, DHC Package): SGND. Must be
soldered to PCB.
U
U
W
FU CTIO AL DIAGRA
INTV
CC
V
IN
PLLIN/MODE
F
IN
PHASE DET
D
B
BOOST
TG
PLLLPF
C
R
LP
B
DROP
OUT
DET
CLK
TOP
BOT
C
IN
D
OSCILLATOR
BOT
TOP ON
FC
SW
C
LP
S
R
Q
Q
SWITCH
LOGIC
INTV
CC
BG
–
+
INTV -0.5V
CC
FC
BURSTEN
SLEEP
C
OUT
PGND
B
+
–
0.4V
V
OUT
–
+
PLLIN/MODE
BURSTEN
SHDN
R
SENSE
0.8V
L
ICMP
IR
+
–
–
+ +
–
+
–
+
SENSE
SENSE
6mV
0.45V
2(V
–
)
FB
SLOPE
COMP
V
FB
R
B
V
FB
–
+
V
IN
TRACK/SS
0.80V
EA
OV
R
A
V
IN
+
–
0.88V
LDO
5.25V
0.5μA
C
C
I
TH
INTV
CC
R
C
C2
6V
C
+
1μA
INTERNAL
SUPPLY
TRACK/SS
SGND
RUN
SHDN
C
SS
3834-1 FD
38341f
8
LTC3834-1
U
OPERATIO
Main Control Loop
(Refer to Functional Diagram)
Shutdown and Start-Up (RUN and TRACK/SS Pins)
The LTC3834-1 uses a constant-frequency, current mode
step-down architecture. During normal operation, each
external top MOSFET is turned on when the clock sets the
RS latch, and is turned off when the main current com-
parator, ICMP, resets the RS latch. The peak inductor
current at which ICMP trips and resets the latch is con-
trolled by the voltage on the ITH pin, which is the output of
the error amplifier EA. The error amplifier compares the
output voltage feedback signal at the VFB pin, (which is
generated with an external resistor divider connected
across the output voltage, VOUT, to ground) to the internal
0.800Vreferencevoltage.Whentheloadcurrentincreases,
it causes a slight decrease in VFB relative to the reference,
which cause the EA to increase the ITH voltage until the
average inductor current matches the new load current.
The LTC3834-1 can be shut down using the RUN pin.
Pulling this pin below 0.7V shuts down the main control
loop for the controller. A low disables the controller and
most internal circuits, including the INTVCC regulator,
at which time the LTC3834-1 draws only 4μA of quies-
cent current.
Releasing the RUN pin allows an internal 0.5μA current to
pull up the pin and enable that controller. Alternatively, the
RUN pin may be externally pulled up or driven directly by
logic. Be careful not to exceed the Absolute Maximum
rating of 7V on this pin.
Thestart-upoftheoutputvoltageVOUT iscontrolledbythe
voltage on the TRACK/SS pin. When the voltage on the
TRACK/SS pin is less than the 0.8V internal reference, the
LTC3834-1 regulates the VFB voltage to the TRACK/SS pin
voltage instead of the 0.8V reference. This allows the
TRACK/SS pin to be used to program a soft-start by
connecting an external capacitor from the TRACK/SS pin
to SGND. An internal 1μA pull-up current charges this
capacitorcreatingavoltagerampontheTRACK/SSpin.As
the TRACK/SS voltage rises linearly from 0V to 0.8V (and
beyond), the output voltage VOUT rises smoothly from
zero to its final value.
After the top MOSFET is turned off each cycle, the bottom
MOSFET is turned on until either the inductor current
starts to reverse, as indicated by the current comparator
IR, or the beginning of the next clock cycle.
INTVCC Power
Power for the top and bottom MOSFET drivers and most
other internal circuitry is derived from the INTVCC pin. An
internal5.25VlowdropoutlinearregulatorsuppliesINTVCC
power from VIN.
Alternatively the TRACK/SS pin can be used to cause the
start-up of VOUT to “track” that of another supply. Typi-
cally, this requires connecting to the TRACK/SS pin an
external resistor divider from the other supply to ground
(see Applications Information section).
The top MOSFET driver is biased from the floating boot-
strap capacitor CB, which normally recharges during each
off cycle through an external diode when the top MOSFET
turns off. If the input voltage VIN decreases to a voltage
close to VOUT, the loop may enter dropout and attempt to
turn on the top MOSFET continuously. The dropout detec-
tor detects this and forces the top MOSFET off for about
onetwelfthoftheclockperiodeverytenthcycletoallowCB
to recharge.
When the RUN pin is pulled low to disable the LTC3834-
1, or when VIN drops below its undervoltage lockout
threshold of 3.5V, the TRACK/SS pin is pulled low by an
internal MOSFET. When in undervoltage lockout, the
controller is disabled and the external MOSFETs are
held off.
38341f
9
LTC3834-1
U
OPERATIO
(Refer to Functional Diagram)
Light Load Current Operation (Burst Mode Operation,
Pulse-Skipping, or Continuous Conduction)
(PLLIN/MODE Pin)
Mode operation. However, continuous operation has the
advantages of lower output ripple and less interference to
audio circuitry. In forced continuous mode, the output
ripple is independent of load current.
The LTC3834-1 can be enabled to enter high efficiency
Burst Mode operation, constant-frequency pulse-skip-
ping mode, or forced continuous conduction mode at low
load currents. To select Burst Mode operation, tie the
PLLIN/MODEpintoaDCvoltagebelow0.8V(e.g., SGND).
To select forced continuous operation, tie the PLLIN/
MODE pin to INTVCC. To select pulse-skipping mode, tie
thePLLIN/MODEpintoaDCvoltagegreaterthan0.8Vand
less than INTVCC – 0.5V.
When the PLLIN/MODE pin is connected for pulse-skip-
ping mode or clocked by an external clock source to use
thephase-lockedloop(seeFrequencySelectionandPhase-
Locked Loop section), the LTC3834-1 operates in PWM
pulse-skipping mode at light loads. In this mode, con-
stant-frequency operation is maintained down to approxi-
mately 1% of designed maximum output current. At very
light loads, the current comparator ICMP may remain
tripped for several cycles and force the external top
MOSFET to stay off for the same number of cycles (i.e.,
skipping pulses). The inductor current is not allowed to
reverse (discontinuous operation). This mode, like forced
continuousoperation, exhibitslowoutputrippleaswellas
low audio noise and reduced RF interference as compared
to Burst Mode operation. It provides higher low current
efficiency than forced continuous mode, but not nearly as
high as Burst Mode operation.
When the LTC3834-1 is enabled for Burst Mode opera-
tion, the peak current in the inductor is set to approxi-
mately one-tenth of the maximum sense voltage even
though the voltage on the ITH pin indicates a lower value.
If the average inductor current is lower than the load
current, theerroramplifierEAwilldecreasethevoltageon
the ITH pin. When the ITH voltage drops below 0.4V, the
internal sleep signal goes high (enabling “sleep” mode)
and both external MOSFETs are turned off. The ITH pin is
thendisconnectedfromtheoutputoftheEAand“parked”
at 0.425V.
Frequency Selection and Phase-Locked Loop (PLLLPF
and PLLIN/MODE Pins)
In sleep mode, much of the internal circuitry is turned off,
reducing the quiescent current that the LTC3834-1 draws
to only 30μA. In sleep mode, the load current is supplied
by the output capacitor. As the output voltage decreases,
the EA’s output begins to rise. When the output voltage
drops enough, the ITH pin is reconnected to the output of
the EA, the sleep signal goes low, and the controller
resumes normal operation by turning on the top external
MOSFET on the next cycle of the internal oscillator.
The selection of switching frequency is a tradeoff between
efficiency and component size. Low frequency operation
increasesefficiencybyreducingMOSFETswitchinglosses,
butrequireslargerinductanceand/orcapacitancetomain-
tain low output ripple voltage.
The switching frequency of the LTC3834-1’s controllers
can be selected using the PLLLPF pin.
If the PLLIN/MODE pin is not being driven by an external
clock source, the PLLLPF pin can be floated, tied to
INTVCC, or tied to SGND to select 400kHz, 530kHz, or
250kHz, respectively.
WhentheLTC3834-1isenabledforBurstModeoperation,
the inductor current is not allowed to reverse. The reverse
current comparator (IR) turns off the bottom external
MOSFET just before the inductor current reaches zero,
preventing it from reversing and going negative, thus
operating in discontinuous operation.
A phase-locked loop (PLL) is available on the LTC3834-1
to synchronize the internal oscillator to an external clock
source that is connected to the PLLIN/MODE pin. In this
case, a series R-C should be connected between the
PLLLPFpinandSGNDtoserveasthePLL’sloopfilter. The
LTC3834-1 phase detector adjusts the voltage on the
PLLLPF pin to align the turn-on of the external top MOS-
In forced continuous operation, the inductor current is
allowed to reverse at light loads or under large transient
conditions.Thepeakinductorcurrentisdeterminedbythe
voltage on the ITH pin, just as in normal operation. In this
mode, the efficiency at light loads is lower than in Burst
FET to the rising edge of the synchronizing signal.
38341f
10
LTC3834-1
U
OPERATIO
(Refer to Functional Diagram)
Output Overvoltage Protection
The typical capture range of the LTC3834-1’s phase-
locked loop is from approximately 115kHz to 800kHz,
with a guarantee to be between 140kHz and 650kHz. In
otherwords, theLTC3834-1’sPLLisguaranteedtolockto
an external clock source whose frequency is between
140kHz and 650kHz.
Anovervoltagecomparatorguardsagainsttransientover-
shoots as well as other more serious conditions that
may overvoltage the output. When the VFB pin rises to
more than 10% higher than its regulation point of
0.800V, the top MOSFET is turned off and the bottom
MOSFET is turned on until the overvoltage condition
is cleared.
The typical input clock thresholds on the PLLIN/MODE pin
are 1.6V (rising) and 1.2V (falling).
W U U
U
APPLICATIO S I FOR ATIO
RSENSE Selection for Output Current
The internal oscillator of the LTC3834-1 runs at a nominal
400kHz frequency when the PLLLPF pin is left floating and
the PLLIN/MODE pin is a DC low or high. Pulling the
PLLLPF to INTVCC selects 530kHz operation; pulling the
PLLLPF to SGND selects 250kHz operation.
RSENSE is chosen based on the required output current.
The current comparator has a maximum threshold of
100mV/RSENSE and an input common mode range of
SGND to 10V. The current comparator threshold sets the
peak of the inductor current, yielding a maximum average
output current IMAX equal to the peak value less half the
Alternatively, the LTC3834-1 will phase-lock to a clock
signal applied to the PLLIN/MODE pin with a frequency
between 140kHz and 650kHz (see Phase-Locked Loop
and Frequency Synchronization).
peak-to-peak ripple current, I .
L
Allowing a margin for variations in the IC and external
component values yields:
Inductor Value Calculation
80mV
IMAX
The operating frequency and inductor selection are inter-
related in that higher operating frequencies allow the use
of smaller inductor and capacitor values. So why would
anyone ever choose to operate at lower frequencies with
larger components? The answer is efficiency. A higher
frequency generally results in lower efficiency because of
MOSFET gate charge losses. In addition to this basic
trade-off, the effect of inductor value on ripple current and
low current operation must also be considered.
RSENSE
=
When using the controller in very low dropout conditions,
the maximum output current level will be reduced due to
the internal compensation required to meet stability crite-
rion for buck regulators operating at greater than 50%
duty factor. A curve is provided to estimate this reduction
in peak output current level depending upon the operating
duty factor.
The inductor value has a direct effect on ripple current.
Operating Frequency and Synchronization
The inductor ripple current I decreases with higher
L
inductance or frequency and increases with higher VIN:
The choice of operating frequency, is a trade-off between
efficiency and component size. Low frequency operation
improvesefficiencybyreducingMOSFETswitchinglosses,
both gate charge loss and transition loss. However, lower
frequency operation requires more inductance for a given
amount of ripple current.
⎛
⎞
⎟
1
VOUT
ΔIL =
VOUT 1–
⎜
(f)(L)
V
IN
⎝
⎠
38341f
11
LTC3834-1
W U U
U
APPLICATIO S I FOR ATIO
Accepting larger values of I allows the use of low
inductances, but results in higLher output voltage ripple
and greater core losses. A reasonable starting point for
Power MOSFET and Schottky Diode (Optional)
Selection
Two external power MOSFETs must be selected for each
controller in the LTC3834-1: One N-channel MOSFET for
the top (main) switch, and one N-channel MOSFET for the
bottom (synchronous) switch.
setting ripple current is I =0.3(IMAX). The maximum I
L
L
occurs at the maximum input voltage.
The inductor value also has secondary effects. The transi-
tion to Burst Mode operation begins when the average
inductor current required results in a peak current below
10% of the current limit determined by RSENSE. Lower
The peak-to-peak drive levels are set by the INTVCC
voltage. This voltage is typically 5V during start-up (see
EXTVCC Pin Connection). Consequently, logic-level
threshold MOSFETs must be used in most applications.
The only exception is if low input voltage is expected
(VIN < 5V); then, sub-logic level threshold MOSFETs
(VGS(TH) < 3V) should be used. Pay close attention to the
BVDSS specification for the MOSFETs as well; most of the
logic level MOSFETs are limited to 30V or less.
inductor values (higher I ) will cause this to occur at
L
lower load currents, which can cause a dip in efficiency in
the upper range of low current operation. In Burst Mode
operation, lower inductance values will cause the burst
frequency to decrease.
Inductor Core Selection
SelectioncriteriaforthepowerMOSFETsincludethe“ON”
resistanceRDS(ON), MillercapacitanceCMILLER, inputvolt-
age and maximum output current. Miller capacitance,
CMILLER, can be approximated from the gate charge curve
usually provided on the MOSFET manufacturers’ data
sheet. CMILLER isequaltotheincreaseingatechargealong
the horizontal axis while the curve is approximately flat
divided by the specified change in VDS. This result is then
multiplied by the ratio of the application applied VDS to the
Gate charge curve specified VDS. When the IC is operating
in continuous mode the duty cycles for the top and bottom
MOSFETs are given by:
Once the value for L is known, the type of inductor must
be selected. High efficiency converters generally cannot
afford the core loss found in low cost powdered iron
cores, forcing the use of more expensive ferrite or
molypermalloy cores. Actual core loss is independent of
coresizeforafixedinductorvalue, butitisverydependent
on inductance selected. As inductance increases, core
losses go down. Unfortunately, increased inductance
requires more turns of wire and therefore copper losses
will increase.
Ferrite designs have very low core loss and are preferred
at high switching frequencies, so design goals can con-
centrate on copper loss and preventing saturation. Ferrite
core material saturates “hard,” which means that induc-
tance collapses abruptly when the peak design current is
exceeded. This results in an abrupt increase in inductor
ripple current and consequent output voltage ripple. Do
not allow the core to saturate!
VOUT
V
IN
Main SwitchDuty Cycle =
V – VOUT
IN
Synchronous SwitchDuty Cycle =
V
IN
38341f
12
LTC3834-1
W U U
APPLICATIO S I FOR ATIO
U
The MOSFET power dissipations at maximum output
current are given by:
could cost as much as 3% in efficiency at high VIN. A 1A
to 3A Schottky is generally a good compromise for both
regions of operation due to the relatively small average
current.Largerdiodesresultinadditionaltransitionlosses
due to their larger junction capacitance.
VOUT
2
PMAIN
=
(
I
1+ δΔT R
+
(
)
)
(
MAX
DS(ON)
V
IN
I
⎛
⎞
2
MAX
2
CIN and COUT Selection
V
R
DR )(
C
MILLER
•
)
(
)
IN
⎜
⎝
⎟
⎠
In continuous mode, the source current of the top MOS-
FETisasquarewaveofdutycycle(VOUT)/(VIN). Toprevent
large voltage transients, a low ESR capacitor sized for the
maximum RMS current of one channel must be used. The
maximum RMS capacitor current is given by:
⎡
⎤
⎥
⎦
1
1
+
f
( )
⎢
⎣
V
INTVCC – VTHMIN VTHMIN
V – VOUT
2
IN
PSYNC
=
I
(
1+ δΔT R
DS(ON)
(
)
)
MAX
1/2
V
IMAX
IN
CIN Required IRMS
≈
V
OUT)(
V – V
IN OUT
(
[
)
]
V
IN
where δ is the temperature dependency of RDS(ON) and
RDR (approximately 2 ) is the effective driver resistance
at the MOSFET’s Miller threshold voltage. VTHMIN is the
typical MOSFET minimum threshold voltage.
This formula has a maximum at VIN = 2VOUT, where IRMS
= IOUT/2. This simple worst-case condition is commonly
usedfordesignbecauseevensignificantdeviationsdonot
offer much relief. Note that capacitor manufacturers’
ripple current ratings are often based on only 2000 hours
of life. This makes it advisable to further derate the
capacitor, or to choose a capacitor rated at a higher
temperature than required. Several capacitors may be
paralleled to meet size or height requirements in the
design. Due to the high operating frequency of the
LTC3834-1, ceramic capacitors can also be used for CIN.
Always consult the manufacturer if there is any question.
BothMOSFETshaveI2RlosseswhilethetopsideN-channel
equation includes an additional term for transition losses,
which are highest at high input voltages. For VIN < 20V the
high current efficiency generally improves with larger
MOSFETs, while for VIN > 20V the transition losses rapidly
increasetothepointthattheuseofahigherRDS(ON)device
withlowerCMILLER actuallyprovideshigherefficiency.The
synchronous MOSFET losses are greatest at high input
voltage when the top switch duty factor is low or during a
short-circuit when the synchronous switch is on close to
100% of the period.
The selection of COUT is driven by the effective series
resistance (ESR). Typically, once the ESR requirement is
satisfied, the capacitance is adequate for filtering. The
output ripple ( V OUT) is approximated by:
The term (1+δΔT) is generally given for a MOSFET in the
form of a normalized RDS(ON) vs Temperature curve, but
δ = 0.005/°C can be used as an approximation for low
voltage MOSFETs.
⎛
⎞
1
ΔVOUT ≈IRIPPLE ESR +
⎜
⎟
8fCOUT
⎝
⎠
The optional Schottky diode D1 shown in Figure 8 con-
ducts during the dead-time between the conduction of the
two power MOSFETs. This prevents the body diode of the
bottom MOSFET from turning on, storing charge during
the dead-time and requiring a reverse recoveryperiod that
where f is the operating frequency, COUT is the output
capacitance and IRIPPLE is the ripple current in the induc-
tor. The output ripple is highest at maximum input voltage
since IRIPPLE increases with input voltage.
38341f
13
LTC3834-1
W U U
U
APPLICATIO S I FOR ATIO
Setting Output Voltage
60
30
0
The LTC3834-1 output voltage is set by an external feed-
back resistor divider carefully placed across the output, as
shown in Figure 1. The regulated output voltage is deter-
mined by:
–30
–60
–90
–120
–150
–180
–210
–240
–270
–300
⎛
⎝
RB ⎞
RA ⎠
VOUT = 0.8V • 1+
⎜
⎟
To improve the frequency response, a feed-forward ca-
pacitor, CFF, may be used. Great care should be taken to
route the VFB line away from noise sources, such as the
inductor and the SW line.
5
10
0
1
2
3
4
6
7
8
9
V
COMMON MODE VOLTAGE (V)
SENSE
38341 G14
Figure 2. SENSE Pins Input Bias Current
vs Common Mode (Output) Voltage
V
OUT
Tracking and Soft-Start (TRACK/SS Pin)
R
B
C
FF
LTC3834-1
V
The start-up of VOUT is controlled by the voltage on the
TRACK/SS pin. When the voltage on the TRACK/SS pin is
less than the internal 0.8V reference, the LTC3834-1
regulates the VFB pin voltage to the voltage on the TRACK/
SS pin instead of 0.8V. The TRACK/SS pin can be used to
program an external soft-start function or to allow VOUT to
“track” another supply during start-up.
FB
R
A
3834-1 F01
Figure 1. Setting Output Voltage
SENSE+ and SENSE– Pins
LTC3834-1
TRACK/SS
The common mode input range of the current comparator
is from 0V to 10V. Continuous linear operation is provided
throughout this range allowing output voltages from 0.8V
to 10V. The input stage of the current comparator requires
that current either be sourced or sunk from the SENSE
pins depending on the output voltage, as shown in the
curve in Figure 2. If the output voltage is below 1.5V,
current will flow out of both SENSE pins to the main
output. In these cases, the output can be easily pre-loaded
by the VOUT resistor divider to compensate for the current
comparator’s negative input bias current. Since VFB is
servoed to the 0.8V reference voltage, RA in Figure 1
should be chosen to be less than 0.8V/ISENSE, with ISENSE
determined from Figure 2 at the specified output voltage.
C
SS
SGND
3834-1 F03
Figure 3. Using the TRACK/SS Pin to Program Soft-Start
Soft-start is enabled by simply connecting a capacitor
from the TRACK/SS pin to ground, as shown in Figure 3.
An internal 1μA current source charges up the capacitor,
providing a linear ramping voltage at the TRACK/SS pin.
The LTC3834-1 will regulate the VFB pin (and hence VOUT
)
according to the voltage on the TRACK/SS pin, allowing
VOUT to rise smoothly from 0V to its final regulated value.
The total soft-start time will be approximately:
0.8V
1μA
tSS = CSS
•
38341f
14
LTC3834-1
W U U
APPLICATIO S I FOR ATIO
U
Alternatively, the TRACK/SS pin can be used to track two
(or more) supplies during start-up, as shown qualitatively
in Figures 4a and 4b. To do this, a resistor divider should
be connected from the master supply (VX) to the TRACK/
SS pin of the slave supply (VOUT), as shown in Figure 5.
Duringstart-upVOUT willtrackVX accordingtotheratioset
by the resistor divider:
INTVCC Regulator
The LTC3834-1 features an internal P-channel low drop-
out linear regulator (LDO) that supplies power at the
INTVCC pin from the VIN supply pin. INTVCC powers the
gate drivers and much of the LTC3834-1’s internal cir-
cuitry. The VIN LDO regulates the voltage at the INTVCC pin
to 5.25V. It can supply a peak current of 50mA and must
be bypassed to ground with a minimum of 4.7μF ceramic
capacitor. The ceramic capacitor placed directly adjacent
to the INTVCC and PGND IC pins is highly recommended.
Good bypassing is needed to supply the high transient
currents required by the MOSFET gate drivers and to
prevent interaction between the channels.
VX
RA
RTRACKA + RTRACKB
RA + RB
=
•
VOUT RTRACKA
For coincident tracking (VOUT = VX during start-up),
RA = RTRACKA
RB = RTRACKB
V (MASTER)
X
V (MASTER)
X
V
(SLAVE)
V
(SLAVE)
OUT
OUT
3834-1 F04B
TIME
TIME
3834-1 F04A
(4a) Coincident Tracking
(4b) Ratiometric Tracking
Figure 4. Two Different Modes of Output Voltage Tracking
V
x
V
OUT
LTC3834-1
FB
RB
V
RA
R
R
TRACKB
TRACK/SS
38341 F05
TRACKA
Figure 5. Using the TRACK/SS Pin for Tracking
38341f
15
LTC3834-1
W U U
U
APPLICATIO S I FOR ATIO
High input voltage applications in which large MOSFETs
are being driven at high frequencies may cause the maxi-
mum junction temperature rating for the LTC3834-1 to be
exceeded. The INTVCC current, which is dominated by the
gate charge current, is supplied by the 5.25V VIN LDO.
Power dissipation for the IC in this case is equal to VIN •
Fault Conditions: Current Limit and Current Foldback
TheLTC3834-1includescurrentfoldbacktohelplimitload
current when the output is shorted to ground. If the output
falls below 70% of its nominal output level, then the
maximum sense voltage is progressively lowered from
100mV to 30mV. Under short-circuit conditions with very
low duty cycles, the LTC3834-1 will begin cycle skipping
in order to limit the short-circuit current. In this situation
the bottom MOSFET will be dissipating most of the power
but less than in normal operation. The short-circuit ripple
current is determined by the minimum on-time tON(MIN) of
the LTC3834-1 ( 200ns), the input voltage and induct-or
value:
I
INTVCC.Thegatechargecurrentisdependentonoperating
frequency as discussed in the Efficiency Considerations
section. The junction temperature can be estimated by
using the equations given in Note 2 of the Electrical
Characteristics. For example, the LTC3834-1 INTVCC cur-
rent is limited to less than 25mA from a 24V supply when
in the GN package:
TJ = 70°C + (25mA)(24V)(90°C/W) = 125°C
I
L(SC) = tON(MIN) (VIN/L)
Topreventthemaximumjunctiontemperaturefrombeing
exceeded, the input supply current must be checked while
operating in continuous conduction mode (PLLIN/MODE
= INTVCC) at maximum VIN.
The resulting short-circuit current is:
30mV
1
ISC
=
– ΔIL(SC)
RSENSE
2
Topside MOSFET Driver Supply (CB, DB)
Fault Conditions: Overvoltage Protection (Crowbar)
External bootstrap capacitors CB connected to the BOOST
pins supply the gate drive voltages for the topside
MOSFET.CapacitorCBintheFunctionalDiagramischarged
though external diode DB from INTVCC when the SW pin is
low. When one of the topside MOSFET is to be turned on,
the driver places the CB voltage across the gate-source of
the desired MOSFET. This enhances the
MOSFET and turns on the topside switch. The switch node
voltage, SW, rises to VIN and the BOOST pin follows.
With the topside MOSFET on, the boost voltage is above
the input supply: VBOOST = VIN + VINTVCC. The value of the
boost capacitor CB needs to be 100 times that of the total
input capacitance of the topside MOSFET(s). The reverse
breakdown of the external Schottky diode must be greater
thanVIN(MAX).Whenadjustingthegatedrivelevel,thefinal
arbiter is the total input current for the regulator. If a
change is made and the input current decreases, then the
efficiency has improved. If there is no change in input
current, then there is no change in efficiency.
The overvoltage crowbar is designed to blow a system
input fuse when the output voltage of the regulator rises
much higher than nominal levels. The crowbar causes
huge currents to flow, that blow the fuse to protect against
a shorted top MOSFET if the short occurs while the
controller is operating.
A comparator monitors the output for overvoltage condi-
tions. The comparator (OV) detects overvoltage faults
greaterthan10%abovethenominaloutputvoltage. When
this condition is sensed, the top MOSFET is turned off and
the bottom MOSFET is turned on until the overvoltage
condition is cleared. The bottom MOSFET remains on
continuously for as long as the OV condition persists; if
VOUT returns to a safe level, normal operation automati-
cally resumes. A shorted top MOSFET will result in a high
current condition which will open the system fuse. The
switching regulator will regulate properly with a leaky
top MOSFET by altering the duty cycle to accommodate
the leakage.
38341f
16
LTC3834-1
W U U
APPLICATIO S I FOR ATIO
U
Phase-Locked Loop and Frequency Synchronization
The output of the phase detector is a pair of complemen-
tary current sources that charge or discharge the external
filter network connected to the PLLLPF pin. The relation-
ship between the voltage on the PLLLPF pin and operating
frequency, when there is a clock signal applied to PLLIN/
MODE, is shown in Figure 6 and specified in the Electrical
Characteristics table. Notethatthe LTC3834-1canonly be
synchronized to an external clock whose frequency is
within range of the LTC3834-1’s internal VCO, which is
nominally 115kHz to 800kHz. This is guaranteed to be
between 140kHz and 650kHz. A simplified block diagram
is shown in Figure 7.
TheLTC3834-1hasaphase-lockedloop(PLL)comprised
of an internal voltage-controlled oscillator (VCO) and a
phase detector. This allows the turn-on of the top MOS-
FET to be locked to the rising edge of an external clock
signalappliedtothePLLIN/MODEpin.Thephasedetector
isanedgesensitivedigitaltypethatprovideszerodegrees
phase shift between the external and internal oscillators.
This type of phase detector does not exhibit false lock to
harmonics of the external clock.
900
800
700
600
500
400
300
200
100
0
1.0
PLLLPF VOLTAGE (V)
2.0
2.5
0
0.5
1.5
3834 G28
Figure 6. Relationship Between Oscillator Frequency and Voltage
at the PLLLPF Pin When Synchronizing to an External Clock
R
LP
2.4V
C
LP
PLLLPF
PLLIN/
MODE
DIGITAL
PHASE/
EXTERNAL
OSCILLATOR
FREQUENCY
DETECTOR
OSCILLATOR
3834-1 F07
Figure 7. Phase-Locked Loop Block Diagram
38341f
17
LTC3834-1
W U U
U
APPLICATIO S I FOR ATIO
If the external clock frequency is greater than the internal
oscillator’s frequency, fOSC, then current is sourced con-
tinuously from the phase detector output, pulling up the
PLLLPF pin. When the external clock frequency is less
than fOSC, current is sunk continuously, pulling down the
PLLLPFpin. Iftheexternalandinternalfrequenciesarethe
same but exhibit a phase difference, the current sources
turn on for an amount of time corresponding to the phase
difference. The voltage on the PLLLPF pin is adjusted until
the phase and frequency of the internal and external
oscillators are identical. At the stable operating point, the
phase detector output is high impedance and the filter
capacitor CLP holds the voltage.
Minimum On-Time Considerations
Minimum on-time tON(MIN) is the smallest time duration
that the LTC3834-1 is capable of turning on the top
MOSFET. Itisdeterminedbyinternaltimingdelaysandthe
gate charge required to turn on the top MOSFET. Low duty
cycle applications may approach this minimum on-time
limit and care should be taken to ensure that
VOUT
tON(MIN)
<
V (f)
IN
Ifthedutycyclefallsbelowwhatcanbeaccommodatedby
the minimum on-time, the controller will begin to skip
cycles. The output voltage will continue to be regulated,
but the ripple voltage and current will increase.
The loop filter components, CLP and RLP, smooth out the
current pulses from the phase detector and provide a
stable input to the voltage-controlled oscillator. The filter
components CLP and RLP determine how fast the loop
acquires lock. Typically RLP = 10k and CLP is 2200pF
to 0.01μF.
Theminimumon-timefortheLTC3834-1isapproximately
200ns. However, as the peak sense voltage decreases the
minimum on-time gradually increases up to about 250ns.
This is of particular concern in forced continuous applica-
tions with low ripple current at light loads. If the duty cycle
drops below the minimum on-time limit in this situation,
a significant amount of cycle skipping can occur with
correspondingly larger current and voltage ripple.
Typically, the external clock (on PLLIN/MODE pin) input
high threshold is 1.6V, while the input low thres-
hold is 1.2V.
Table 1 summarizes the different states in which the
PLLLPF pin can be used.
Table 1
PLLLPF PIN
0V
PLLIN/MODE PIN
DC Voltage
FREQUENCY
250kHz
400kHz
Floating
DC Voltage
INTV
DC Voltage
530kHz
CC
RC Loop Filter
Clock Signal
Phase-Locked to External Clock
38341f
18
LTC3834-1
W U U
APPLICATIO S I FOR ATIO
U
Efficiency Considerations
RSENSE, but is “chopped” between the topside MOS-
FET and the synchronous MOSFET. If the two MOS-
FETs have approximately the same RDS(ON), then the
resistanceofoneMOSFETcansimplybesummedwith
the resistances of L, RSENSE and ESR to obtain I2R
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can be
expressed as:
losses. For example, if each RDS(ON) = 30m , R
=
L
50m , R
= 10m and R
= 40m (sum of
both inpuStEaNnSdE output capacitaEnScRe losses), then the
total resistance is 130m . This results in losses rang-
ing from 3% to 13% as the output current increases
from 1A to 5A for a 5V output, or a 4% to 20% loss for
a3.3Voutput. Efficiencyvariesastheinversesquareof
VOUT for the same external components and output
power level. The combined effects of increasingly
lower output voltages and higher currents required by
high performance digital systems is not doubling but
quadruplingtheimportanceoflosstermsintheswitch-
ing regulator system!
%Efficiency = 100% – (L1 + L2 + L3 + ...)
whereL1, L2, etc. aretheindividuallossesasapercentage
of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC3834-1 circuits: 1) IC VIN current, 2) INTVCC
regulator current, 3) I2R losses, 4) Topside MOSFET
transition losses.
1. TheVIN currenthastwocomponents:thefirstistheDC
supply current given in the Electrical Characteristics
table, which excludes MOSFET driver and control cur-
rents; the second is the current drawn from the 3.3V
linear regulator output. VIN current typically results in
a small (<0.1%) loss.
4. TransitionlossesapplyonlytothetopsideMOSFET(s),
and become significant only when operating at high
input voltages (typically 15V or greater). Transition
losses can be estimated from:
Transition Loss = (1.7) VIN2 IO(MAX) CRSS
f
2. INTVCC current is the sum of the MOSFET driver and
control currents. The MOSFET driver current results
from switching the gate capacitance of the power
MOSFETs. Each time a MOSFET gate is switched from
low to high to low again, a packet of charge dQ moves
fromINTVCC toground.TheresultingdQ/dtisacurrent
out of INTVCC that is typically much larger than the
control circuit current. In continuous mode, IGATECHG
=f(QT+QB), whereQT andQB arethegatechargesofthe
topside and bottom side MOSFETs.
3. I2R losses are predicted from the DC resistances of the
fuse (if used), MOSFET, inductor, current sense resis-
tor, and input and output capacitor ESR. In continuous
mode the average output current flows through L and
Other “hidden” losses such as copper trace and internal
battery resistances can account for an additional 5% to
10% efficiency degradation in portable systems. It is very
important to include these “system” level losses during
the design phase. The internal battery and fuse resistance
losses can be minimized by making sure that CIN has
adequate charge storage and very low ESR at the switch-
ing frequency. A 25W supply will typically require a mini-
mum of 20μF to 40μF of capacitance having a maximum
of 20m to 50m of ESR. Other losses including
Schottky conduction losses during dead-time and induc-
tor core losses generally account for less than 2% total
additional loss.
38341f
19
LTC3834-1
W U U
U
APPLICATIO S I FOR ATIO
Checking Transient Response
gain and phase. An output current pulse of 20% to 80% of
full-load current having a rise time of 1μs to 10μs will
produce output voltage and ITH pin waveforms that will
give a sense of the overall loop stability without breaking
the feedback loop. Placing a power MOSFET directly
across the output capacitor and driving the gate with an
appropriate signal generator is a practical way to produce
a realistic load step condition. The initial output voltage
step resulting from the step change in output current may
not be within the bandwidth of the feedback loop, so this
signal cannot be used to determine phase margin. This is
why it is better to look at the ITH pin signal which is in the
feedback loop and is the filtered and compensated control
loop response. The gain of the loop will be increased by
increasing RC and the bandwidth of the loop will be
increased by decreasing CC. If RC is increased by the same
factor that CC is decreased, the zero frequency will be kept
the same, thereby keeping the phase shift the same in the
most critical frequency range of the feedback loop. The
outputvoltagesettlingbehaviorisrelatedtothestabilityof
the closed-loop system and will demonstrate the actual
overall supply performance.
The regulator loop response can be checked by looking at
the load current transient response. Switching regulators
take several cycles to respond to a step in DC (resistive)
load current. When a load step occurs, VOUT shifts by an
amount equal to I LOAD (ESR), where ESR is the effective
series resistance of COUT. I LOAD also begins to charge or
discharge COUT generating the feedback error signal that
forces the regulator to adapt to the current change and
return VOUT to its steady-state value. During this recovery
time VOUT can be monitored for excessive overshoot or
ringing, which would indicate a stability problem.
OPTI-LOOP compensation allows the transient response
to be optimized over a wide range of output capacitance
and ESR values. The availability of the ITH pin not only
allows optimization of control loop behavior but also
provides a DC coupled and AC filtered closed loop re-
sponse test point. The DC step, rise time and settling at
this test point truly reflects the closed loop response.
Assuming a predominantly second order system, phase
margin and/or damping factor can be estimated using
the percentage of overshoot seen at this pin. The band-
width can also be estimated by examining the rise time at
the pin. The ITH external components shown in Figure 10
circuit will provide an adequate starting point for most
applications.
A second, more severe transient is caused by switching in
loads with large (>1μF) supply bypass capacitors. The
dischargedbypasscapacitorsareeffectivelyputinparallel
with COUT, causing a rapid drop in VOUT. No regulator can
alter its delivery of current quickly enough to prevent this
sudden step change in output voltage if the load switch
resistance is low and it is driven quickly. If the ratio of
CLOAD to COUT is greater than 1:50, the switch rise time
should be controlled so that the load rise time is limited to
approximately 25 • CLOAD. Thus a 10μF capacitor would
require a 250μs rise time, limiting the charging current to
about 200mA.
The ITH series RC-CC filter sets the dominant pole-zero
loop compensation. The values can be modified slightly
(from 0.5 to 2 times their suggested values) to optimize
transient response once the final PC layout is done and the
particular output capacitor type and value have been
determined. The output capacitors need to be selected
because the various types and values determine the loop
38341f
20
LTC3834-1
W U U
APPLICATIO S I FOR ATIO
U
Design Example
1.8V
22V
2
PMAIN
=
5
1+ (0.005)(50°C – 25°C) •
( )
[
]
As a design example, assume VIN = 12V(nominal), VIN =
22V(max), VOUT = 1.8V, IMAX = 5A, and f = 250kHz.
5A
2
⎛
⎞
2
0.035Ω + 22V
) (
4Ω 215pF •
)(
(
)
(
)
⎜
⎝
⎟
⎠
Theinductancevalueischosenfirstbasedona30%ripple
current assumption. The highest value of ripple current
occurs at the maximum input voltage. Tie the PLLLPF pin
to GND, generating 250kHz operation. The minimum
inductance for 30% ripple current is:
1
1
⎡
⎤
+
300kHz = 332mW
(
)
⎢
⎣
⎥
⎦
5 – 2.3 2.3
A short-circuit to ground will result in a folded back cur-
rent of:
⎛
⎜
⎝
⎞
⎟
⎠
VOUT
(f)(L)
VOUT
ΔIL =
1–
V
IN
⎛
⎞
25mV 1 120ns(22V)
ISC
=
–
= 2.1A
⎜
⎟
⎠
A 4.7μH inductor will produce 23% ripple current and a
3.3μH will result in 33%. The peak inductor current will be
the maximum DC value plus one half the ripple current, or
5.84A, for the 3.3μH value. Increasing the ripple current
will also help ensure that the minimum on-time of 180ns
is not violated. The minimum on-time occurs at maxi-
mum VIN:
0.01Ω 2⎝ 3.3μH
withatypicalvalueofRDS(ON)andδ=(0.005/°C)(20)=0.1.
The resulting power dissipated in the bottom MOSFET is:
22V – 1.8V
22V
= 100mW
2
PSYNC
=
2.1A 1.125 0.022Ω
(
) (
)(
)
VOUT
1.8V
which is less than under full-load conditions.
tON(MIN)
=
=
= 327ns
V
IN(MAX)f 22V(250kHz)
CIN is chosen for an RMS current rating of at least 3A at
temperature assuming only this channel is on. COUT is
chosen with an ESR of 0.02 for low output ripple. The
output ripple in continuous mode will be highest at the
maximum input voltage. The output voltage ripple due to
ESR is approximately:
The RSENSE resistor value can be calculated by using the
maximum current sense voltage specification with some
accommodation for tolerances:
80mV
5.84A
RSENSE
≤
≈ 0.012Ω
VORIPPLE = RESR ( I ) = 0.02 (1.67A) = 33mV
L
P–P
Choosing 1% resistors: R1 = 25.5k and R2 = 32.4k yields
an output voltage of 1.816V.
The power dissipation on the top side MOSFET can be
easily estimated. Choosing a Fairchild FDS6982S dual
MOSFET results in: RDS(ON) = 0.035 /0.022 , C
MILLER
= 215pF. At maximum input voltage with T(estimated)
= 50°C:
38341f
21
LTC3834-1
W U U
U
APPLICATIO S I FOR ATIO
PC Board Layout Checklist
4. Are the SENSE – and SENSE+ leads routed together
with minimum PC trace spacing? The filter capacitor
between SENSE+ and SENSE– should be as close as
possibletotheIC.Ensureaccuratecurrentsensingwith
Kelvin connections at the SENSE resistor.
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of the
IC. These items are also illustrated graphically in the
layout diagram of Figure 8. The Figure 9 illustrates the
current waveforms present in the various branches of the
synchronous regulator operating in the continuous mode.
Check the following in your layout:
5. Is the INTVCC decoupling capacitor connected close to
theIC, betweentheINTVCC andthepowergroundpins?
This capacitor carries the MOSFET drivers current
peaks. An additional 1μF ceramic capacitor placed
immediatelynexttotheINTVCC andPGNDpinscanhelp
improve noise performance substantially.
1. Is the top N-channel MOSFET M1 located within 1cm
of CIN?
2. Are the signal and power grounds kept separate? The
combined IC signal ground pin and the ground return
of CINTVCC must return to the combined COUT (–) termi-
nals. The path formed by the top N-channel MOSFET,
Schottky diode and the CIN capacitor should have short
leads and PC trace lengths. The output capacitor (–)
terminals should be connected as close as possible to
the (–) terminals of the input capacitor by placing the
capacitorsnexttoeachotherandawayfromtheSchottky
loop described above.
6. Keep the switching node (SW), top gate node (TG), and
boost node (BOOST) away from sensitive small-signal
nodes, especially from the opposites channel’s voltage
and current sensing feedback pins. All of these nodes
have very large and fast moving signals and therefore
should be kept on the “output side” of the LTC3834-1
and occupy minimum PC trace area.
7. Use a modified “star ground” technique: a low imped-
ance, large copper area central grounding point on the
same side of the PC board as the input and output
capacitors with tie-ins for the bottom of the INTVCC
decoupling capacitor, the bottom of the voltage feed-
back resistive divider and the SGND pin of the IC.
3. DoestheLTC3834-1VFB pinresistivedividerconnectto
the (+) terminals of COUT? The resistive divider must be
connected between the (+) terminal of COUT and signal
ground. The feedback resistor connections should not
be along the high current input feeds from the input
capacitor(s).
TRACK/SS
+
L1
R
SENSE
V
SENSE
TG
OUT
–
SENSE
SW
C
D
LTC3834EGN-1
BOOST
B
M1
M2
D1
Optional
V
FB
PLLLPF
V
IN
C
OUT
f
IN
PLLIN/MODE
RUN
BG
1μF
CERAMIC
R
IN
B
C
VIN
GND
I
INTV
TH
CC
C
IN
V
IN
C
INTVCC
SGND
PGND
3834-1 F08
Figure 8. LTC3834-1 Recommended Printed Circuit Layout Diagram
38341f
22
LTC3834-1
W U U
APPLICATIO S I FOR ATIO
U
L1
R
SENSE
SW
V
OUT
V
IN
R
IN
C
IN
D1
C
R
L1
OUT
3834-1 F09
BOLD LINES INDICATE HIGH SWITCHING
CURRENT. KEEP LINES TO A MINIMUM LENGTH.
Figure 9. Branch Current Waveforms
PC Board Layout Debugging
lems coincide with high input voltages and low output
currents,lookforcapacitivecouplingbetweentheBOOST,
SW, TG, and possibly BG connections and the sensitive
voltage and current pins. The capacitor placed across the
current sensing pins needs to be placed immediately
adjacent to the pins of the IC. This capacitor helps to
minimize the effects of differential noise injection due to
high frequency capacitive coupling. If problems are en-
countered with high current output loading at lower input
voltages,lookforinductivecouplingbetweenCIN,Schottky
and the top MOSFET components to the sensitive current
and voltage sensing traces. In addition, investigate com-
mon ground path voltage pickup between these compo-
nents and the SGND pin of the IC.
It is helpful to use a DC-50MHz current probe to monitor
the current in the inductor while testing the circuit. Moni-
tor the output switching node (SW pin) to synchronize the
oscilloscope to the internal oscillator and probe the actual
output voltage as well. Check for proper performance over
the operating voltage and current range expected in the
application. The frequency of operation should be main-
tained over the input voltage range down to dropout and
until the output load drops below the low current opera-
tion threshold—typically 10% of the maximum designed
current level in Burst Mode operation.
The duty cycle percentage should be maintained from
cycle to cycle in a well-designed, low noise PCB imple-
mentation. Variation in the duty cycle at a subharmonic
rate can suggest noise pickup at the current or voltage
sensing inputs or inadequate loop compensation. Over-
compensation of the loop can be used to tame a poor PC
layout if regulator bandwidth optimization is not required.
An embarrassing problem, which can be missed in an
otherwise properly working switching regulator, results
when the current sensing leads are hooked up back-
wards. The output voltage under this improper hookup
will still be maintained but the advantages of current
mode control will not be realized. Compensation of the
voltage loop will be much more sensitive to component
selection. This behavior can be investigated by tempo-
rarily shorting out the current sensing resistor—don’t
worry, the regulator will still maintain control of the
output voltage.
ReduceVIN fromitsnominalleveltoverifyoperationofthe
regulator in dropout. Check the operation of the under-
voltage lockout circuit by further lowering VIN while moni-
toring the outputs to verify operation.
Investigate whether any problems exist only at higher
output currents or only at higher input voltages. If prob-
38341f
23
LTC3834-1
U
TYPICAL APPLICATIO S
High Efficiency 9.5V, 3A Step-Down Converter
PLLLPF
RUN
V
IN
V
IN
10V TO 36V
C
10μF
IN
M1
TG
0.01μF
C
B
0.22μF
TRACK/SS
L1
BOOST
SW
7.2μH
V
OUT
0.015Ω
I
TH
9.5V
3A
560pF
LTC3834-1
100pF
105k
C
OUT
SGND
PLLIN/MODE
INTV
CC
150μF
4.7μF
39.2k
M2
V
FB
BG
–
+
SENSE
SENSE
432k
PGND
22pF
38341 TA02
M1, M2: Si4840DY
L1: CDEP105-7R2M
C : SANYO 10TPD150M
OUT
High Efficiency 12V to 1.8V, 2A Step-Down Converter
PLLLPF
RUN
V
IN
V
IN
12V
C
10μF
IN
M1
TG
0.01
C
B
0.22μF
TRACK/SS
BOOST
SW
TBD
V
1.8V
2A
TBD
OUT
I
TH
1000pF
LTC3834-1
100pF
48.7k
SGND
PLLIN/MODE
INTV
CC
C
OUT
4.7μF
68.1k
100μF
CERAMIC
M2
V
FB
BG
–
+
SENSE
SENSE
84.5k
PGND
100pF
38341 TA03
M1, M2: Si4840DY
L1 TOKO 053LC A915AY-3R3M
38341f
24
LTC3834-1
U
TYPICAL APPLICATIO S
High Efficiency 5V, 5A Step-Down Converter
PLLLPF
RUN
V
IN
V
IN
5.5V TO
36V
C
10μF
IN
M1
TG
0.01μF
C
B
0.22μF
TRACK/SS
L1
BOOST
SW
3.3μH
V
0.012Ω
OUT
I
TH
5V
5A
560pF
LTC3834-1
150pF
54k
C
OUT
150μF
SGND
PLLIN/MODE
INTV
CC
4.7μF
69.8k
M2
V
BG
FB
–
+
SENSE
SENSE
365k
39pF
PGND
38341 TA04
M1, M2: Si4840DY
L1: CDEP105-3R2M
C
: SANYO 10TPD150M
OUT
High Efficiency 1.2V, 5A Step-Down Converter
GND
PLLLPF
RUN
V
IN
V
IN
4V TO
36V
C
10μF
IN
M1
TG
0.01μF
C
B
0.22μF
TRACK/SS
L1
BOOST
SW
2.2μH
V
0.012Ω
OUT
I
TH
1.2V
5A
2.2nF
26.1k
LTC3834-1
100pF
C
OUT
150μF × 2
SGND
PLLIN/MODE
INTV
CC
4.7μF
68.1k
M2
V
BG
FB
–
+
SENSE
SENSE
34k
PGND
390pF
38341 TA05
M1, M2: Si4840DY
L1: CDEP105-2R2M
C
: SANYO 10TPD150M
OUT
38341f
25
LTC3834-1
U
PACKAGE DESCRIPTIO
DHC Package
16-Lead Plastic DFN (5mm × 3mm)
(Reference LTC DWG # 05-08-1706)
0.65 ±0.05
3.50 ±0.05
1.65 ±0.05
2.20 ±0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 ± 0.05
0.50 BSC
4.40 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
R = 0.115
TYP
0.40 ± 0.10
5.00 ±0.10
(2 SIDES)
9
16
R = 0.20
TYP
3.00 ±0.10 1.65 ± 0.10
(2 SIDES)
(2 SIDES)
PIN 1
TOP MARK
(SEE NOTE 6)
PIN 1
NOTCH
(DHC16) DFN 1103
8
1
0.25 ± 0.05
0.75 ±0.05
0.200 REF
0.50 BSC
4.40 ±0.10
(2 SIDES)
0.00 – 0.05
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WJED-1) IN JEDEC
PACKAGE OUTLINE MO-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
38341f
26
LTC3834-1
U
PACKAGE DESCRIPTIO
GN Package
16-Lead Plastic SSOP (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1641)
.189 – .196*
(4.801 – 4.978)
.045 ±.005
.009
(0.229)
REF
16 15 14 13 12 11 10 9
.254 MIN
.150 – .165
.229 – .244
.150 – .157**
(5.817 – 6.198)
(3.810 – 3.988)
.0165 ± .0015
.0250 BSC
RECOMMENDED SOLDER PAD LAYOUT
1
2
3
4
5
6
7
8
.015 ± .004
(0.38 ± 0.10)
× 45°
.0532 – .0688
(1.35 – 1.75)
.004 – .0098
(0.102 – 0.249)
.007 – .0098
(0.178 – 0.249)
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
.0250
(0.635)
BSC
.008 – .012
GN16 (SSOP) 0204
(0.203 – 0.305)
TYP
NOTE:
1. CONTROLLING DIMENSION: INCHES
INCHES
2. DIMENSIONS ARE IN
(MILLIMETERS)
3. DRAWING NOT TO SCALE
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
38341f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tationthattheinterconnectionofitscircuitsasdescribedhereinwillnotinfringeonexistingpatentrights.
27
LTC3834-1
U
TYPICAL APPLICATIO
PLLLPF
RUN
V
IN
V
IN
4V TO 36V
C
IN
10μF
TG
0.01μF
C
B
0.22μF
TRACK/SS
BOOST
SW
I
TH
L1
3.2μH 0.012Ω
560pF
54k
LTC3834-1
V
3.3V
5A
OUT
D
B
150pF
CMDSH-3
SGND
PLLIN/MODE
INTV
CC
C
OUT
150μF
4.7μF
68.1k
V
FB
BG
–
+
SENSE
SENSE
215k
PGND
39pF
38341 TA06
M1, M2: Si4840DY
L1: CDEP 105-3R2M
C : SANYO 10TPD150M
OUT
Figure 10. High Efficiency 3.3V, 5A Step-Down Converter
RELATED PARTS
PART NUMBER
LTC1735
DESCRIPTION
High Efficiency Synchronous Step-Down Switching Regulator Output Fault Protection, 16-Pin SSOP
No R Current Mode Synchronous Step-Down Up to 97% Efficiency, 4V 36V, 0.8V
Up to 20A
COMMENTS
LTC1778/LTC1778-1
V
V
(0.9)(V ),
OUT IN
SENSE
IN
Controllers
Dual, 2-Phase, DC/DC Controller with Output Tracking
I
OUT
LTC3708
Current Mode, No R , Up/Down Tracking, Synchronizable
SENSE
LTC3727/LTC3727-1
High Efficiency, 2-Phase, Synchronous Step-Down Switching 2-Phase Operation; 4V
V
36V, 0.8V
V
14V,
OUT
IN
Regulators
99% Duty Cycle, 5mm × 5mm QFN, SSOP-28
LTC3728
LTC3729
Dual, 550kHz, 2-Phase Synchronous Step-Down
Controller
20A to 200A, 550kHz PolyPhase Synchronous Controller
Dual 180° Phased Controllers, V 3.5V to 35V, 99% Duty Cycle,
IN
5mm × 5mm QFN Package, SSOP-28
Expandable from 2-Phase to 12-Phase, Uses All Surface Mount
Components, V Up to 36V
IN
LTC3731
LT3800
3- to 12-Phase Step-Down Synchronous Controller
High Voltage Synchronous Regulator Controller
60A to 240A Output Current, 0.6V V
6V, 4.5V V
32V
IN
OUT
V
up to 60V, I
20A, Current Mode, Onboard Bias
OUT
IN
Regulator, Burst Mode Operation, 16-Lead TSSOP Package
LTC3826/LTC3826-1
LTC3827/LTC3827-1
30μA I , Dual, 2-Phase Synchronous Step-Down Controller
Q
2-Phase Operation; 30μA One Channel No Load I (50μA Total),
Q
4V
V
36V, 0.8V
V
10V
OUT
IN
Low I Dual Synchronous Controllers
2-Phase Operation; 115μA Total No Load I , 4V
V
36V
IN
Q
Q
80μA No Load I with One Channel On
Q
LTC3835/LTC3835-1
LT3844
Low I Synchronous Step-Down Controller
80μA No Load I , 4V
V
36V, 0.8V
V
10V
OUT
Q
Q
IN
High Voltage Current Mode Controller with
Programmable Operating Frequency
V
up to 60V, I
5A Onboard Bias Regulator, Burst Mode
OUT
IN
Operation, Sync Capability, 16-Lead TSSOP Package
LTC3845
LTC3850
Low I Synchronous Step-Down Controller
4V
2-Phase Operation; 4V
No R Option, I
V
60V, 1.23V
V
36V, 120μA Quiescent Current
24V, 95% Efficiency,
Q
IN
OUT
Dual, 2-Phase Synchronous Step-Down DC/DC Controller
V
IN
Up to 20A, 4mm × 4mm QFN
OUT
SENSE
No RSENSE is a trademark of Linear Technology Corporation. PolyPhase is a registered trademark of Linear Technology Corporation. Pentium is a registered trademark of Intel Corporation.
38341f
LT 1107 • PRINTED IN USA
LinearTechnology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
28
© LINEAR TECHNOLOGY CORPORATION 2007
●
●
(408) 432-1900 FAX: (408) 434-0507 www.linear.com
相关型号：
LTC3835EDHC-1#PBF
LTC3835-1 - Low IQ Synchronous Step-Down Controller; Package: DFN; Pins: 16; Temperature Range: -40°C to 85°C
Linear
LTC3835EDHC-1#TR
LTC3835-1 - Low IQ Synchronous Step-Down Controller; Package: DFN; Pins: 16; Temperature Range: -40°C to 85°C
Linear
©2020 ICPDF网 联系我们和版权申明