RH1086BKK [Linear]
IC,VOLT REGULATOR,ADJUSTABLE,+1.23 TO +25V,BIPOLAR, RAD HARD,TO-204/-3,3PIN,METAL;型号: | RH1086BKK |
厂家: | Linear |
描述: | IC,VOLT REGULATOR,ADJUSTABLE,+1.23 TO +25V,BIPOLAR, RAD HARD,TO-204/-3,3PIN,METAL |
文件: | 总17页 (文件大小:569K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
REVISION RECORD
DESCRIPTION
REV
DATE
0
A
INITIAL RELEASE
PAGE 11, FIGURES 6, 7, CHANGED θja AND θjc.
PAGE 3, PARAGRAPH 3.8 CHANGED VERBIAGE ADDED “HEREIN” AFTER TABLE 1.
06/02/98
09/24/99
B
03/07/01
PAGE 4, PARAGRAPH 5.0 CHANGED VERBIAGE ADDED “HEREIN” AFTER TABLE 3.
PARAGRAPH 5.2 ADDED “HEREIN” AFTER TABLE 2.
PARAGRAPH 6.2 ADDED “HEREIN” AFTER TABLE 3.
PAGE 5, 6.3 CHANGED VERBIAGE ADDED “HEREIN” AFTER TABLE 3.
• REMOVED THE “M” FROM THE DEVICE TITLE, THROUGHOUT THE SPEC, TO MATCH THE
DATA SHEET AND RPL.
C
07/16/02
• PAGE 3, PARAGRAPH 3.6 CHANGED TO REFLECT ONLY FIGURE 1 FOR BOTH DEVICE
OPTIONS.
PARAGRAPH 3.7.1, CHANGED THE DOSAGE RATE FROM “APPROXIMATELY 20 RADS PER
SECOND” TO “LESS THAN OR EQUAL TO 10 RADS PER SECOND”.
PARAGRAPH 3.7.3, NOW REFLECTS TOTAL DOSE BIAS AS FIGURE 2.
• PAGE 4, PARAGRAPH 5.5, NOW REFLECTS BURN-IN CIRCUITS AS FIGURES 3 AND 4.
PARAGRAPH 5.6, NOW REFLECTS CASE OUTLINES AS FIGURES 5 AND 6.
PARAGRAPH 5.7, NOW REFLECTS TERMINAL CONNECTIONS AS FIGURES 7 AND 8.
PARAGRAPH 6.1 CHANGED QUALITY ASSURANCE PROVISIONS TO STATE THAT LTC IS
QML CERTIFIED AND THAT RAD HARD CANDIDATES ARE ASSEMBLED ON QUALIFIED
CLASS S MANUFACTURING LINES.
• PAGES 6 THROUGH 12, ALL FIGURE TITLES CHANGED TO HAVE DEVICE OPTIONS AND
PACKAGE TYPES AT TOP OF PAGE, AND HAVE ALL FIGURES AT BOTTOM OF PAGE.
• CONVERSION OF SPECIFICATION FROM WORD PERFECT TO MICROSOFT WORD.
CAUTION: ELECTROSTATIC DISCHARGE SENSITIVE PART
REVISION
INDEX
PAGE NO.
REVISION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
E
15
E
16
E
E
E
E
E
E
E
E
E
E
E
E
E
E
LINEAR TECHNOLOGY CORPORATION
MILPITAS, CALIFORNIA
TITLE: MICROCIRCUIT, LINEAR,
RH1086BHK, 0.5A AND RH1086BKK, 1.5A,
LOW DROPOUT POSITIVE
ORIG
DSGN
ENGR
MFG
CM
REGULATOR DICE
SIZE
CAGE
CODE
64155
DRAWING
NUMBER
05-08-5134
REV
QA
PROG
E
APPLICATION
FUNCT
SIGNOFFS
DATE CONTRACT:
FOR OFFICIAL USE ONLY
LINEAR TECHNOLOGY CORPORATION
Page 1 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
REVISION RECORD
DESCRIPTION
CHANGED RH1086H TO RH1086BHK AND RH1086K TO RH1086BKK THROUGHOUT SPEC.
REV
DATE
D
10/28/03
E
•
PAGE 3, CHANGED INITIAL RATE OF RADS TO 240 RADS/SEC.
FOR OFFICIAL USE ONLY
LINEAR TECHNOLOGY CORPORATION
Page 2 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
1.0
2.0
SCOPE:
1.1
This specification defines the performance and test requirements for a microcircuit processed to a
space level manufacturing flow.
APPLICABLE DOCUMENTS:
2.1 Government Specifications and Standards: the following documents listed in the Department of
Defense Index of Specifications and Standards, of the issue in effect on the date of solicitation,
form a part of this specification to the extent specified herein.
SPECIFICATIONS:
MIL-PRF-38535
Integrated Circuits (Microcircuits) Manufacturing, General Specification
for
MIL-STD-883
MIL-STD-1835
Test Method and Procedures for Microcircuits
Microcircuits Case Outlines
2.2
Order of Precedence: In the event of a conflict between the documents referenced herein and the
contents of this specification, the order of precedence shall be this specification, MIL-PRF-38535
and other referenced specifications.
3.0
REQUIREMENTS:
3.1
General Description: This specification details the requirements for the RH1086BHK, 0.5A and
RH1086BKK, 1.5A, Low Dropout Positive Regulator Dice and Element Evaluation Test Samples,
processed to space level manufacturing flow as specified herein.
3.2
Part Number:
3.2.1 OPTION 1 – RH1086BHK Dice
3.2.2 OPTION 2 – RH1086BKK Dice
3.3
Special Handling of Dice: Rad Hard dice require special handling as compared to standard IC
dice. Rad Hard dice are susceptible to surface damage due to the absence of silicon nitride
passivation as on standard dice. Silicon nitride protects the dice surface from scratches by it’s hard
and dense properties. The passivation on Rad Hard dice is silicon dioxide which is much “softer”
than silicon nitride.
LTC recommends that dice handling be performed with extreme care so as to protect the dice
surface from scratches. If the need arises to move the die around from the chip tray, use a Teflon
tipped vacuum wand. This wand can be made by pushing a small diameter of Teflon tubing onto
the tip of a steel tipped wand. The inside diameter of the Teflon tip should match the dice size for
efficient pickup. The tip of the Teflon should be cut square and flat to ensure good vacuum to dice
surface. Ensure the Teflon tip remains clean from debris by inspecting under stereo scope.
During die attach, care must be exercised to ensure no tweezers touch the top of the dice.
LINEAR TECHNOLOGY CORPORATION
Page 3 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
3.4
The Absolute Maximum Ratings:
.
.
Power Dissipation
Input to Output Voltage Differential
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Internally Limited
25V
.
.
Operating Junction Temperature Range
Control Section
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
-55°C to +150°C
-55°C to +200°C
-65°C to +150°C
300°C
Power Transistor
Storage Temperature Range
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Lead Temperature (Soldering, 10 sec)
3.5
3.6
3.7
Design, Construction, and Physical Dimensions: Detail design, construction, physical dimensions,
and electrical requirements shall be specified herein.
Outline Dimensions and Pad Functions: Dice outline dimensions, pad functions, and locations shall
be specified in Figure 1.
Radiation Hardness Assurance (RHA):
3.7.1
3.7.2
3.7.3
The manufacturer shall perform a lot sample test as an internal process monitor for total
dose radiation tolerance. The sample test is performed using a non-certified cobalt 60
source at an initial rate of 240 rads/sec with a predetermined exponential decay.
For guaranteed radiation performance to MIL-STD-883, Method 1019, total dose
irradiation, the manufacturer will provide certified RAD testing and report through an
independent test laboratory when required as a customer purchase order line item.
Total dose bias circuit is specified in Figure 2.
3.8
Wafer (or Dice) Probe: Dice shall be 100% probed at Ta = +25°C to the limits shown in Table I
herein. All reject dice shall be removed from the lot. This testing is normally performed prior to
dicing the wafer into chips. Final specifications after assembly are sample tested during the
element evaluation.
3.9
Wafer Lot Acceptance: Wafer lot acceptance shall be in accordance with MIL-PRF-38535,
Appendix A, except for the following: Top side glassivation thickness shall be a minimum of
4KÅ.
3.10
3.11
Wafer Lot Acceptance Report: SEM is performed per MIL-STD-883, Method 2018. Copies of
SEM photographs shall be supplied with the Wafer Lot Acceptance Report as part of a Space Data
Pack when specified as a customer purchase order line item.
Traceability: Wafer Diffusion Lot and Wafer traceability shall be maintained through Quality
Conformance Inspection.
4.0
5.0
QUALITY CONFORMANCE INSPECTION: Quality Conformance Inspection shall consist of the tests
and inspections specified herein.
SAMPLE ELEMENT EVALUATION: A sample from each wafer supplying dice shall be assembled and
subjected to element evaluation per Table III herein.
LINEAR TECHNOLOGY CORPORATION
Page 4 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
5.1
100 Percent Visual Inspection: All dice supplied to this specification shall be inspected in
accordance with MIL-STD-883, Method 2010, Condition A. All reject dice shall be removed from
the lot.
5.2
5.3
Electrical Performance Characteristics for Element Evaluation: The electrical performance
characteristics shall be as specified in Table I and Table II herein.
Sample Testing: Each wafer supplying dice for delivery to this specification shall be subjected to
element evaluation sample testing. No dice shall be delivered until all the lot sample testing has
been performed and the results found to be acceptable unless the customer supplies a written
approval for shipment prior to completion of wafer qualification as specified in this specification.
5.4
Part Marking of Element Evaluation Sample Includes:
5.4.1 LTC Logo
5.4.2 LTC Part Number
5.4.3 Date Code
5.4.4 Serial Number
5.4.5 ESD Identifier per MIL-PRF-38535, Appendix A
5.4.6 Diffusion Lot Number
5.4.7 Wafer Number
5.5
5.6
Burn-In Requirement: Burn-In circuit for TO39 package is specified in Figure 3 and Burn-In
circuit for TO3 package is specified in Figure 4.
Mechanical/Packaging Requirements: Case Outline and Dimensions are in accordance with
Figure 5 and Figure 6.
5.7
5.8
Terminal Connections: The terminal connections shall be as specified in Figure 7 and Figure 8.
Lead Material and Finish: The lead material and finish shall be Kovar for device option 1 and
Alloy 42 for device option 2, with hot solder dip (Finish letter A) in accordance with MIL-PRF-
38535.
6.0
VERIFICATION (QUALITY ASSURANCE PROVISIONS)
6.1
Quality Assurance Provisions: Quality Assurance provisions shall be in accordance with MIL-
PRF-38535. Linear Technology is a QML certified company and all Rad Hard candidates are
assembled on qualified Class S manufacturing lines.
6.2
6.3
Sampling and Inspection: Sampling and Inspection shall be in accordance with Table III herein.
Screening: Screening requirements shall be in accordance with Table III herein.
LINEAR TECHNOLOGY CORPORATION
Page 5 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
6.4
Source Inspection:
6.4.1 The manufacturer will coordinate Source Inspection at wafer lot acceptance and pre-seal
internal visual.
6.4.2 The procuring activity has the right to perform source inspection at the supplier’s facility
prior to shipment for each lot of deliverables when specified as a customer purchase order
line item. This may include wafer lot acceptance, die visual, and final data review.
6.5
Deliverable Data: Deliverable data that will ship with devices when a Space Data Pack is ordered:
6.5.1 Lot Serial Number Sheets identifying all Canned Sample devices accepted through final
inspection by serial number.
6.5.2 100% attributes (completed element evaluation traveler).
6.5.3 Element Evaluation variables data, including Burn-In and Op Life
6.5.4 SEM photographs (3.10 herein)
6.5.5 Wafer Lot Acceptance Report (3.9 herein)
6.5.6 A copy of outside test laboratory radiation report if ordered
6.5.7 Certificate of Conformance certifying that the devices meet all the requirements of this
specification and have successfully completed the mandatory tests and inspections herein.
Note: Items 6.5.1 and 6.5.7 will be delivered as a minimum, with each shipment.
7.0
Packaging Requirements: Packaging shall be in accordance with Appendix A of MIL-PRF-38535. All dice
shall be packaged in multicavity containers composed of conductive, anti-static, or static dissipative
material with an external conductive field shielding barrier.
LINEAR TECHNOLOGY CORPORATION
Page 6 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
DICE OUTLINE DIMENSIONS AND PAD FUNCTIONS
OPTION 1, RH1086BHK, 0.5A DICE AND OPTION 2, RH1086BKK, 1.5A DICE
“H” OR “K” (DEPENDING ON THE DEVICE OPTION)
WILL BE REFLECTED HERE
FIGURE 1
LINEAR TECHNOLOGY CORPORATION
Page 7 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
TOTAL DOSE BIAS CIRCUIT
FIGURE 2
LINEAR TECHNOLOGY CORPORATION
Page 8 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
TO39 STATIC BURN-IN CIRCUIT
OPTION 1, T039 METAL CAN / 3 LEADS
FIGURE 3
LINEAR TECHNOLOGY CORPORATION
Page 9 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
STATIC BURN-IN CIRCUIT
OPTION #2, TO3 / 2 LEADS
FIGURE 4
LINEAR TECHNOLOGY CORPORATION
Page 10 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
DEVICE OPTION # 1
(H) TO39 METAL CAN / 3 LEADS CASE OUTLINE
FIGURE 5
θja = +150°C/W
θjc = +40°C/W
LINEAR TECHNOLOGY CORPORATION
Page 11 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
DEVICE OPTION # 2
(K) TO3 METAL CAN / 2 LEADS CASE OUTLINE
θja = +35°C/W
θjc = +3°C/W
FIGURE 6
LINEAR TECHNOLOGY CORPORATION
Page 12 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
TERMINAL CONNECTIONS
DEVICE OPTION #1, TO39 / 3 LEAD METAL CAN
FIGURE 7
DEVICE OPTION #2, TO3 / 2 LEAD METAL CAN
FIGURE 8
LINEAR TECHNOLOGY CORPORATION
Page 13 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
TABLE I DICE ELECTRICAL CHARACTERISTICS – Element Evaluation (Note 1)
LINEAR TECHNOLOGY CORPORATION
Page 14 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
TABLE II ELECTRICAL CHARACTERISTICS (POSTIRRADIATION)
TA = 25°C unless otherwise noted.
LINEAR TECHNOLOGY CORPORATION
Page 15 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
TABLE III RH ELEMENT EVALUATION TABLE QUALLIFICATION OF DICE SALES
LINEAR TECHNOLOGY CORPORATION
Page 16 of 16
SPEC NO. 05-08-5134 REV. E
RH1086BHK, 0.5A AND RH1086BKK , 1.5A
LOW DROPOUT POSITIVE REGULATOR DICE
LINEAR TECHNOLOGY CORPORATION
Page 17 of 16
相关型号:
RH1086BKKDICE
IC VREG ADJUSTABLE POSITIVE LDO REGULATOR, 1.5 V DROPOUT, MBFM2, METAL CAN, T03, 2 PIN, Adjustable Positive Single Output LDO Regulator
Linear
RH1086MH
IC VREG ADJUSTABLE POSITIVE LDO REGULATOR, 1.5 V DROPOUT, MBCY3, METAL CAN, TO-39, 3 PIN, Adjustable Positive Single Output LDO Regulator
Linear
RH1086MH#PBF
IC VREG ADJUSTABLE POSITIVE LDO REGULATOR, 1.5 V DROPOUT, MBCY3, METAL CAN, TO-39, 3 PIN, Adjustable Positive Single Output LDO Regulator
Linear
RH1086MK
IC VREG ADJUSTABLE POSITIVE LDO REGULATOR, 1.5 V DROPOUT, MBFM2, METAL CAN, TO-3, 2 PIN, Adjustable Positive Single Output LDO Regulator
Linear
©2020 ICPDF网 联系我们和版权申明