58562-2 [MACOM]

PRO-CRIMPER III Hand Crimping Tool;


型号：	58562-2
厂家：	Tyco Electronics
描述：	PRO-CRIMPER III Hand Crimping Tool
文件：	总4页 (文件大小：127K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Instruction Sheet

PRO- CRIMPER* III Hand

Crimping Tool Assembly 58562-1

with Die Assembly 58562-2

408-4080

15 JAN 10 Rev B

PROPER USE GUIDELINES

Cumulative Trauma Disorders can resultfrom the prolonged use ofmanually powered hand tools. Hand tools are intended for occasional use and low volume

applications. A wide selection of powered application equipment for extended-use, production operations is available.

Stationary Jaw

Front of Tool

Back of Tool

(Wire Side)

Pivot Pin

Die Assembly

PRO-CRIMPER III Hand

Crimping Tool Frame

354940-1 (408-9930)

Moving Jaw

Ratchet

Adjustment

Wheeel

The PRO-CRIMPER III Hand Crimping Tool is a “Commercial” grade hand

tool and is designed primarily for field installation, repair, maintenance work, or

prototyping in industrial, commercial, or institutional applications. Product

crimped with this tool will meet the crimp height requirement for hand tools in

the appropriate 114 series specification, but may not comply with other feature

parameters of the specification. Tyco Electronics offers a variety of tools to

satisfy your performance requirements. For additional information, contact the

Tooling Assistance Center at 1-800-722-1111.

Stationary

Handle

Moving Handle

Wire

Contact Family^{

TE Die Assembly

Strip Length

mm [In.]

Size (AWG)

Insul Dia

2.29 to 3.30

[.090 to .130]

4.75

[.187]

58561--2

.250 FASTON* Receptacle

22--18

{ Supplied with die assembly. Also available separately..

} Contact the TOOLING ASSISTANCE CENTER or PRODUCT INFORMATION (see below) for specific contact part numbers.

Figure 1

Dimensions on this sheet are in millimeters [with

inch equivalents provided in brackets]. Figures

and illustrations are for identification only and are

not drawn to scale.

1. INTRODUCTION

NOTE

PRO--CRIMPER III Hand Crimping Tool

Assembly 58562--1 consists of Die Assembly

58562--2 and PRO--CRIMPER III Hand Crimping Tool

Frame 354940--1. The die assembly consists of wire

and insulation crimping dies.

2. DESCRIPTION (Figures 1 and 2)

The tool features a tool frame with a stationary jaw

and handle, a moving jaw, a moving handle, and an

adjustable ratchet that ensures full contact crimping.

The tool frame holds a die assembly with two

crimping sections.

Read these instructions thoroughly before crimping

any terminals.

Reasons for reissue are provided in Section 10,

REVISION SUMMARY.

The die assembly features a wire anvil, an insulation

anvil, a wire crimper, and an insulation crimper.

TOOLING ASSISTANCE CENTER 1-800-722-1111

PRODUCT INFORMATION 1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.tycoelectronics.com

E2010 Tyco Electronics Corporation, Harrisburg, PA

1 of 4

All International Rights Reserved

TE logo and Tyco Electronics are trademarks.

LOC B

*Trademark. Other products, logos, and company names used are the property of their respective owners.

408-4080

PRO-CRIMPER III Hand Crimping Tool Assembly 58562-1

Tool Frame

Insulationn

Crimper

Chamfer

Die Retaining

Pins

Wire Crimper

Wire Anvil

Insulation

Anvil

Die Retaining

Screws

Chamfer

Figure 2

Die retaining pins and die retaining screws are used

to position and secure the dies in the tool frame.

9. To disassemble, close the tool handles until the

ratchet releases, remove the two die retaining

screws and the four die retaining pins, and slide

the anvils and crimpers out of the tool jaws.

3. INSTALLATION AND REMOVAL OF DIE SET (Figure 2)

4. CRIMPING PROCEDURE

1. Open the tool handles and remove the two die

retaining screws from the tool jaws.

This tool is provided with a crimp adjustment

feature. Initially, the crimp height should be

verified as specified in Figure 4. Refer to

Section 5, CRIMP HEIGHT INSPECTION, and

Section 6, RATCHET (Crimp Height)

ADJUSTMENT, to verify crimp height before

using the tool to crimp desired terminals and wire

sizes.

NOTE

2. Place the wire anvil and insulation anvil so that

their chamfered sides and their marked surfaces

face outward, when mounted in the moving jaw of

the tool frame.

3. Insert the two die retaining pins.

4. Insert a die retaining screw through the jaw

and through both anvil dies, and tighten the screw

just enough to hold the dies in place. Do not

tighten the screw completely at this time.

Refer to the table in Figure 1 and select wire of the

specified size and insulation diameter. Strip the wire

to the length indicated in Figure 1, taking care not to

nick or cut wire strands. Select an applicable terminal

and identify the appropriate crimp section according

to the wire size markings on the tool. Refer to

Figure 3 and proceed as follows:

5.Place the wire crimper and insulation crimper so

that their chamfered sides and their marked

surfaces face outward, when mounted in the

stationary jaw of the tool frame.

1. Hold the tool so that the back (wire side) is

facing you. Squeeze tool handles together and

allow them to open fully.

6. Insert the two die retaining pins.

7. Insert a die retaining screw through the jaw

and through both crimper dies, and tighten the

screw just enough to hold the dies in place. Do not

tighten the screw completely at this time.

2. Holding the terminal by the mating end, insert

the terminal — insulation barrel first — through the

front of the tool and into the appropriate crimp

section.

8. Carefully close the tool handles, making sure

that the anvils and crimpers align properly.

Continue closing the tool handles until the ratchet

in the tool frame has engaged sufficiently to hold

the anvils and crimpers in place, then tighten both

die retaining screws.

3. Position the terminal so that the mating end of

the terminal is on the front side of the tool, and so

that the open “U” of the wire and insulation barrels

face the top of the tool. Place the terminal up into

the nest.

2 of 4

Tyco Electronics Corporation

Rev B

408-4080

PRO-CRIMPER III Hand Crimping Tool Assembly 58562-1

4. Rotate the tool sufficiently to be able to view the

front side of the wire crimper, and position the

terminal so that the front edge of the wire barrel is

even with the front edge of the wire crimper, as

shown in Figure 3.

9. Check the terminal’s crimp height as described

in Section 5, CRIMP HEIGHT INSPECTION. If

necessary, adjust the crimp height as described in

Section 6, RATCHET (Crimp Height)

ADJUSTMENT.

Make sure that both sides of the insulation barrel

are started evenly into the crimping section. Do

NOT attempt to crimp an improperly positioned

terminal.

CAUTION

5. CRIMP HEIGHT INSPECTION

Crimp height inspection is performed through the use

of a micrometer with a modified anvil, commonly

referred to as a crimp--height comparator. Tyco

Electronics does not manufacture or market

crimp--height comparators. Detailed information on

obtaining and using crimp--height comparators can be

found in instruction sheet 408--7424.

5. Hold the terminal in position and squeeze the

tool handles together until ratchet engages

sufficiently to hold the terminal in position. Do NOT

deform insulation barrel or wire barrel.

6. Rotate the tool so that the back (wire side) is

once again facing you.

Proceed as follows:

7. Insert stripped wire into terminal insulation and

wire barrels until the end of the wire is even with

the edge of the wire barrel and wire crimper, as

shown in Figure 3.

1. Refer to Figure 4 and select a wire (maximum

size) for each crimp section listed.

2. Refer to Section 4, CRIMPING PROCEDURE,

and crimp the contact(s) accordingly.

8. Holding the wire in place, squeeze tool handles

together until ratchet releases. Allow tool handles

to open and remove crimped terminal.

3. Using a crimp height comparator, measure the

wire barrel crimp height as shown in Figure 4. If the

crimp height conforms to that shown in the table,

the tool is considered dimensionally correct. If not,

the tool must be adjusted. Refer to Section 6,

RATCHET (Crimp Height) ADJUSTMENT.

The crimped terminal may stick in the crimping

area, but the terminal can be easily removed by

pushing downward on the mating end of the

terminal.

NOTE

Front of the Wire

Wire Crimper

Back of Tool

(Wire Side)

Barrel Even with

Edge of Wire Crimper

Strip

Length

Wire Barrel

Terminal (Typ)

Wire

Figure 3

Rev B

Tyco Electronics Corporation

3 of 4

408-4080

PRO-CRIMPER III Hand Crimping Tool Assembly 58562-1

Position Point

on Center of

Wire Barrel

Opposite

secure the lockscrew. If the dimension is

unacceptable, continue to adjust the ratchet, and

again measure a sample crimp.

Seam

7. MAINTENANCE

Ensure that the tool and dies are clean by wiping

them with a clean, soft cloth. Remove any debris with

a clean, soft brush. Do not use objects that could

damage the tool. When not in use, keep handles

closed to prevent objects from becoming lodged in

the crimping dies, and store in a clean, dry area.

Modified Anvil

“A”

Crimp Height

Dimension A

Wire Size

AWG (Max)

Crimp Section

(Wire Size Marking))

and Tolerance (+)

1.230 + .05

22--20

[.0485 + .0020]

8. VISUAL INSPECTION

1.40 + .05

[.055 + .0020]

The crimping dies should be inspected on a regular

basis to ensure that they have not become worn or

damaged. Inspect the crimp sections for flattened,

chipped, worn, or broken areas. If damage or

abnormal wear is evident, the tool must be replaced.

See Section 9, REPLACEMENT.

Figure 4

6. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)

1. Remove the lockscrew from the ratchet

adjustment wheel.

9. REPLACEMENT

Customer--replaceable parts are shown in Figure 1.

2. With a screwdriver, adjust the ratchet wheel

from the front side of the tool.

Available separately, PRO--CRIMPER III Hand

Crimping Tool Repair Kit 679221--1 includes a

replacement nut and a variety of pins, rings, screws,

and springs.

3. Observe the ratchet adjustment wheel. If a

tighter crimp is required, rotate the adjustment

wheel COUNTERCLOCKWISE to a

higher--numbered setting. If a looser crimp is

required, rotate the adjustment wheel

CLOCKWISE to a lower--numbered setting.

If the dies are damaged or worn excessively, they

must be replaced.

Order the repair kit and replaceable parts through

your Tyco Electronics representative, or call

1--800--526--5142, or send a facsimile of your

purchase order to 1--717--986--7605, or write to:

4. Replace the lockscrew.

Screwdriver

CUSTOMER SERVICE (38--35)

TYCO ELECTRONICS

PO BOX 3608

HARRISBURG PA 17105--3608

10. REVISION SUMMARY

Ratchet

Adjustment

Wheel

Revisions to this instruction sheet include:

S Logo change;

S Changed PRO--CRIMPER II to

PRO--CRIMPER III Hand Crimping Tool.

Lockscrew

(Typ)

Figure 5

5. Make a sample crimp and measure the crimp

height. If the dimension is acceptable, replace and

4 of 4

Tyco Electronics Corporation

Rev B

58562-2 [MACOM]

相关型号：

5856B

5856BK001

5856BL001

5856BR001

5856BR005

5856SL001

5857-3100

5857-31000

5857-5100

5857B

5857BK005

5857BK007