91376--1 [MACOM]
Seating Tools 91347- [ ], 91350- [ ]; 休息工具91347- [] ， 91350- []
| 型号： | 91376--1 |
| 厂家： | 
Tyco Electronics |
| 描述： | Seating Tools 91347- [ ], 91350- [ ] |
| 文件： | 总4页 (文件大小：106K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Instruction Sheet
Seating Tools 91347-[ ], 91350-[ ], and
91376-[ ] for Z-PACK* Hard Metric (HM)-Zd
Receptacle Connectors
408-8500
21 JUN 10 Rev F
Seating Tool 91376-1
(Shown)
HM -Zd 3-Pair Receptacle
Connector (Shown)
Printed Circuit (PC)
Board
Eye-of -Needle
Contacts
SEATING
TOOL
CONNECTOR
TYPE
91350--[ ]
91376--[ ]
91347--[ ]
2--Pair
3--Pair
4--Pair
PC Board Support Fixture
(Custom Designed)
Figure 1
1. INTRODUCTION
2. DESCRIPTION
The seating tool is a one--piece design. During
seating, the seating tool covers the connector and
presses on the top surface of the connector when the
applicator ram applies force to the seating tool.
Seating Tools 91347--[ ], 91350--[ ], and 91376--[ ] are
used to seat Z--PACK HM--Zd receptacle connectors
onto a pc board. See Figure 1. Dash number
indicates number of connector columns. The
connectors contain eye--of--needle contacts which
allow solderless pc board installation.
3. REQUIREMENTS
3.1. PC Board Support Fixture (Custom Designed)
All numerical values in this instruction sheet are
in metric units [with U.S. customary units in
brackets]. Dimensions are in millimeters [and
inches]. Figures are not drawn to scale.
NOTE
A pc board support must be used to provide proper
support for the pc board and alignment of the tool to
the contacts and to protect the pc board and contacts
from damage.
i
3.2. Application Tooling
Read these instructions and understand them before
using the seating tool.
Power for seating tools must be provided by a
machine capable of supplying a downward force of
89 Newtons (N) [20 lb] per contact. Manual Electric
Servo Press (MEP 6T) 1585699--1, Bench Top
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
E2010 Tyco Electronics Corporation, Berwyn, PA
1 of 4
All Rights Reserved
TE logo and Tyco Electronics are trademarks.
LOC B
*Trademark. Other product names, logos, or company names might be trademarks of their respective owners.
408-8500
5. Center the seating tool (with the connector)
under the ram of the applicator tool; slowly lower
the ram until it just meets the seating tool. Verify
the alignment of the pc board support fixture, pc
board, connector, and seating tool.
Seating Tools 91347-[ ], 91350-[ ], and 91376-[ ]
Electric Servo Presses (BMEP 3T) 1585697--1, and
(BMEP 5T) 1585696--1 are available for this seating
tool. For information on the presses, visit the press--fit
assembly equipment website at
http://tooling.tycoelectronics.com/pressfit.asp.
Over -driving of the connector will deform parts
Damage to the pc board, seating tool, or
CAUTION
CAUTION
critical to the quality of the connection. Maximum
connector may occur if the seating height is
force occurs prior to the connector bottoming on
the pc board.
improperly set, the pc board is not properly
!
!
positioned over the pc board support, or the
seating tool is not properly seated on the
connector before cycling the applicator ram.
4. SEATING
1. Set seating height to the dimension shown in
Figure 2 (application tool shut height will equal the
tool seating height PLUS the combined
thicknesses of the pc board and support fixture).
After seating, a gap of no more than 0.10 mm
[.004 in.] between the connector housing and the
pc board is allowed.
6. Cycle the ram according to instructions included
with the application tooling. Check the connector
for proper seating using the requirements in
Application Specification 114--13059.
7. Remove the pc board or re--position the pc
board and pc board support fixture for seating
additional connectors.
NOTE
The seating height of 38.1 mm [1.50 in.] is a
reference starting point. The seating height might
have to be adjusted to properly seat the
connector onto the pc board.
5. MAINTENANCE AND INSPECTION
5.1. Daily Maintenance
i
2. Position the connector on the pc board so that
contacts are properly aligned with the holes in the
pc board and pc board support fixture.
It is recommended that each operator be made aware
of, and responsible for, the following steps of daily
maintenance:
3. Sit the connector onto pc board until the open
section of the contacts are resting securely on, but
have not fully entered, the holes in the pc board.
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or lint--free cloth. DO NOT
use objects that could damage the tool or any of its
components.
4. Position the seating tool onto the connector.
View After Seating
Note: Not to Scale
Applicator Ram
(Fully Down)
Seating Height
(Connector Seated)
38.1 [1.50] Ref
Seating Tool Centered Under
Applicator Ram and
Bottomed on Connector
Maximum Gap
Applicator Tooling
Shut Height
(Ram Down)
Allowed
0.10 mm [.004 in.]
Contacts in PC Board Holes and Aligned
with Holes in PC Board Support Fixture
PC Board Support Fixture
PC Board
Figure 2
2 of 4
Tyco Electronics Corporation
Rev F
408-8500
Seating Tools 91347-[ ], 91350-[ ], and 91376-[ ]
2. Ensure that the screws are in place and
secured.
6. REPLACEMENT AND REPAIR
Order replacement seating tools through your local
Tyco Electronics Representative, or call
1--800--526--5142, or send a facsimile of your
purchase order to 717--986--7605, or write to:
3. When the tool is not in use, store it in a clean,
dry area.
5.2. Inspection
CUSTOMER SERVICE (038--035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
Each seating tool is assembled and inspected before
shipment. It is recommended that the tool be
inspected using Figure 3 immediately upon arrival to
assure that it has not been damaged during shipment.
HARRISBURG PA 17105--3608
7. REVISION SUMMARY
Regular inspections should be performed by quality
control personnel. A record of scheduled inspections
should remain with the tool or be supplied to
personnel responsible for the tool. The inspection
frequency should be based on the amount of use,
working conditions, operator training and skill, and
established company standards.
Revisions to this instruction sheet include:
S Updated document to corporate requirements
S Added new text to Paragraph 3.2
S Added seating tool dimension to Figure 2
Seating Tool 91347-[ ] (4-Pair Connector)
25.4
[1.00]
22.5
[.884]
4.44 [.175]
(F Places)
33.0
[1.30]
A
B
D
E
C
DIMENSION
C
SEATING TOOL
F
A
B
D
E
91347--1
91347--2
91347--3
91347--4
91347--5
5.46 [.215]
5.21 [.205]
5.26 [.207]
5.18 [.204]
5.38 [.212]
15.49 [.610]
27.69 [1.090]
20.24 [.797]
15.19 [.598]
—
25.4 [1.000]
37.34 [1.470]
29.97 [1.180]
49.78 [1.960]
12.70 [.500]
—
—
2
2
2
4
1
—
—
—
30.18 [1.188]
—
—
40.18 [1.582]
—
Figure 3 (Cont’d)
Rev F
Tyco Electronics Corporation
3 of 4
408-8500
Seating Tools 91347-[ ], 91350-[ ], and 91376-[ ]
Seating Tool 91350-[ ] (2-Pair Connector)
29.5
[1.163]
32.3
[1.27]
4.44 [.175]
(F Places)
19
[.750]
A
24.1
[.950]
B
D
E
C
DIMENSION
C
SEATING TOOL
F
A
B
D
E
—
91350--1
91350--2
5.46 [.215]
5.18 [.204]
15.49 [.610]
15.19 [.598]
25.4 [1.000]
49.78 [1.960]
—
2
4
30.18 [1.188]
40.18 [1.582]
Seating Tool 91376-[ ] (3-Pair Connector)
29.97
[1.180]
26.97
[1.062]
A
28.58
[1.125]
4.44 [.175]
(2 Places)
B
C
DIMENSION
B
SEATING TOOL
A
C
91376--1
91376--2
5.46 [.215]
5.18 [.204]
15.49 [.610]
15.19 [.598]
25.4 [1.000]
49.78 [1.960]
Figure 3 (End)
4 of 4
Tyco Electronics Corporation
Rev F
相关型号：
©2020 ICPDF网 联系我们和版权申明