D-110-0217 [MACOM]
SolderSleeve Discrete Wire Terminators;
| 型号： | D-110-0217 |
| 厂家： | 
Tyco Electronics |
| 描述： | SolderSleeve Discrete Wire Terminators |
| 文件： | 总4页 (文件大小：117K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Wire Termination to Pin/Post/Tab
SolderSleeve Discrete Wire Terminators
Product Facts
I Transparent polyvinylidene
fluoride or polyolefin
insulation sleeve provides
encapsulation,
inspectability, strain relief,
and insulation
I Prefluxed solder preform
offers a controlled soldering
process
I One-piece design means
easy installation and low
installed cost
I Optional tape carrier
provides convenience and
ease of installation
I UL and CUL
Recognized
R
Applications
Installation
Used for terminating wires
to component terminals,
such as motor tabs, con-
nector pins, and switch
terminals.
For proper installation of
these devices, the correct
heating tool and reflector
attachment must be used.
Either of the following
5. Optional: Select tape
carrier center-to-center
spacing (D-71X series
only). This should match
center spacing of com-
ponent terminals.
Raychem heating tools are
recommended:
Product selection process
6. Select part number from
the appropriate table:
1. Determine the application
operating temperature.
I HL1802E
I AA-400 Super Heater
I For CWT series
2. From the Product Options
table on the next page,
select the product series
appropriate for the appli-
cation, based on the tem-
perature required.
(applications with low-
temperature wires—
below 125°C [257°F]),
use Table A.
Refer to Raychem installa-
tion procedure RCPS 200-
12 (for D-129, D-141, D-71X)
or RPIP 824-00 (for CWT)
for detailed instructions and
recommended reflector
attachment.
8
I For D-129/141/71X
series (applications with
wires rated higher than
125°C [257°F]), use
Table B.
3. Determine your compo-
nent connection point
type (pin, post, or tab)
and dimensions.
You will find ordering infor-
mation for these tools see
section 10.
4. Determine your wire
gauge.
Available in:
Americas
Europe
Asia Pacific
I
I
I
8-39
Catalog 1654025
Revised 12-04
Dimensions are in millimeters
and inches unless otherwise
specified. Values in brackets
are U.S. equivalents.
Dimensions are shown for
USA: 1-800-522-6752
South America: 55-11-3611-1514
Japan: 81-44-900-5102
Singapore: 65-4866-151
UK: 44-1793-528171
reference purposes only.
Specifications subject
to change.
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
www.tycoelectronics.com
Wire Termination to Pin/Post/Tab
SolderSleeve Discrete Wire Terminators (Continued)
Product Options
Product Series
CWT
Max. Operating Temperature
125°C [257°F]
Min. Wire Temperature Rating
85°C [185°F]
D-129, D-141, D-71X
150°C [302°F]
125°C [257°F]
Note: Cadmium-free option (B-152 series) is available for operating temperature of 125˚C [257˚F].
Consult Tyco Electronics for details.
Table A. CWT Series
(125°C [257°F] rated)
Connection-point
Type and Size
Terminal Dimensions
Wire AWG/mm2
Part No.
24 [0.24]
20 [0.61]
CWT-1501
CWT-1502
W = up to 0.63 [.025]
W
24 [0.24]
22 [0.38]
20 [0.61]
CWT-1501
CWT-1502
CWT-1503
W = 0.63 [.025] to
0.89 [0.035]
pin
W
W = 0.89 [0.035] to
1.14 [.045]
24–22 [0.24–0.38]
20–18 [0.61–0.95]
CWT-1502
CWT-1503
W = 1.14 [.045] to
1.52 [.060]
24–22 [0.24–0.38]
20–18 [0.61–0.95]
CWT-1503
CWT-1504
post
W = up to1.52 [.060]
24–20 [0.24–0.61]
24-18 [0.24–0.95]
CWT-1501
CWT-1502
W = 1.27 [.050] to
2.28 [.090]
W
W = 1.77 [.070] to
2.79 [.110]
24-18 [0.24–0.95]
CWT-1503
tab
W = 2.54 [.100] to
3.80 [.150]
24-18 [0.24–0.95]
22-16 [0.38–1.21]
CWT-1504
CWT-1505
W = 2.28 [.090] to
4.70 [.187]
8-40
Catalog 1654025
Revised 12-04
Dimensions are in millimeters
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
South America: 55-11-3611-1514
Japan: 81-44-900-5102
Singapore: 65-4866-151
UK: 44-1793-528171
and inches unless otherwise
specified. Values in brackets
are U.S. equivalents.
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
www.tycoelectronics.com
Wire Termination to Pin/Post/Tab
SolderSleeve Discrete Wire Terminators (Continued)
Table B. D-129/141/71X Series
(up to 150°C [302°F] rated)
Connection-point
Type and Size
Tape Carrier Spacing of Sleeves (Center-to-Center)
Wire
Terminal
Dimensions
1.27
2.54
3.17
4.0
[0.156]
AWG
mm2
None
[0.050]
[0.100]
[0.125]
W
30–26
24–22
[0.05–0.15]
[0.24–0.38]
D-141-30
D-141-07
D-713-03
—
—
—
—
—
—
W = up to 0.61 [.024]
D-711-00
W = 0.63 [.025] to
0.81 [.032]
[0.61]
D-141-31
D-141-56
—
—
D-711-04
—
D-711-07
—
D-711-08
—
20
pin
W
W = 0.76 [.030] to
1.27 [.050]
24–20
[0.24–0.61]
W = up to 1.52 [.060]
24–20
[0.24–0.61]
D-129-05
—
D-714-01
—
—
post
W
W = 1.27 [.050] to
2.28 [.090]
24–20
24–20
[0.24–0.61]
[0.24–0.61]
D-129-03
—
—
—
—
—
—
D-714-00
—
W = 2.28 [.090] to
3.55 [.140]
D-129-0043
tab
For Fine Wire Terminations
0.15 mm2 (26 AWG) and
Smaller*
Part
No.*
Inside Diameter
As Supplied**
Fully
Length††
Recovered†
0.6 [0.025]
0.6 [0.025]
0.75 [0.030]
0.75 [0.030]
0.75 [0.030]
D-110-0062
D-110-0217
D-141-13
D-141-22
D-141-30
1.0 [0.040]
16.0 [0.630]
9.0 [0.360]
4.7 [0.185]
6.0 [0.240]
9.5 [0.375]
1.0 [0.040]
0.75 x 1.65 [0.030 X 0.065]
0.75 x 1.65 [0.030 X 0.065]
0.75 x 1.65 [0.030 X 0.065]
8
Note: Micro SolderSleeve terminators are used for attaching leads smaller than 26 AWG (0.15 mm2) to terminals less
than 0.6 [.025] wide.
*The D-110 series sleeves are primarily for single wire terminations and do not have a wire stop. The D-141 series will
accept either one or two wires; the parts have a built-in wire stop that will locate the wire approximately 0.76 [0.03]
from bottom of terminal.
**Minimum. Wire insulation must be smaller than this. When using the D-141 parts for two-wire terminations, the com-
bined wire insulation diameters must be less than 1.5 [.060].
†Maximum. The combination of conductor diameter and terminal width and the wire insulation must be greater than
this.
††The terminal length should be at least 1.2 [0.05] shorter than this. The wire strip length must be adjusted so that,
when terminated, the exposed conductor is covered by the sleeve.
8-41
Catalog 1654025
Revised 12-04
Dimensions are in millimeters
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
South America: 55-11-3611-1514
Japan: 81-44-900-5102
Singapore: 65-4866-151
UK: 44-1793-528171
and inches unless otherwise
specified. Values in brackets
are U.S. equivalents.
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
www.tycoelectronics.com
Wire Termination to Pin/Post/Tab
SolderSleeve Discrete Wire Terminators (Continued)
Product Characteristics
Material
Insulation [D-129, D-141, D-71X]
Insulation [CWT]
Radiation-crosslinked, heat-shrinkable polyvinylidene fluoride
Radiation-crosslinked, heat-shrinkable polyolefin
Solder and flux [D-129, D-141, D-71X]
Solder and flux [CWT]
Typical Performance
Solder: Sn63 Pb37
Flux: ROL1 per ANSI -J - 004 [RMA flux]
Flux: ROM1 per ANSI -J - 004 [RA flux]
Solder: Sn50 Pb32 Cd 18
Voltage drop
2.0 mV
Tensile strength
Exceeds strength of conductor
2.0 kV
Dielectric strength
Temperature rating [CWT]
Temperature rating [D-129, D-141, D-71X]
Insulation resistance
-55°C to 125°C [-67°F to 257°F]
-55°C to 150°C [-67°F to 302°F]
1000 megohms
Specifications/Approvals
Series
CWT
Agency
Raychem
D-5023
UL and CUL E87681
UL and CUL E87681
D-129, D-141
RT-1404
8-42
Catalog 1654025
Revised 12-04
Dimensions are in millimeters
and inches unless otherwise
specified. Values in brackets
are U.S. equivalents.
Dimensions are shown for
USA: 1-800-522-6752
South America: 55-11-3611-1514
Japan: 81-44-900-5102
Singapore: 65-4866-151
UK: 44-1793-528171
reference purposes only.
Specifications subject
to change.
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
www.tycoelectronics.com
相关型号：
©2020 ICPDF网 联系我们和版权申明