MT3A-0113H [MARKIMICROWAVE]
TWO-TONE-TERMINATOR MIXER/LO-AMPLIFIER;
| 型号： | MT3A-0113H |
| 厂家： | 
Marki |
| 描述： | TWO-TONE-TERMINATOR MIXER/LO-AMPLIFIER 放大器 |
| 文件： | 总8页 (文件大小：736K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TWO-TONE-TERMINATOR MIXER/LO-AMPLIFIER
MT3A-0113H
The MT3A-0113H is a versatile, robust, and broadband Two-Tone-
Terminator mixer integrated with a low phase noise LO driver amplifier.
The MT3A-0113H employs the most sophisticated mixer on the market
today and offers unparalleled performance when compared to all other
mixer technologies. The MT3A-0113H delivers exceptional IMD
suppression with low conversion loss and high IP3. The integrated
positive bias only LO amplifier allows for high linearity with low LO drive
levels down to just +5dBm.
Die
Module
Features
Ultra-Broadband RF, LO, and IF
Integrated Low Phase Noise LO Amplifier
Up to +30dBm IIP3
Low LO drive requirements down to +5dBm
Application Note: T3 Mixer Primer
Electrical Specifications - Specifications guaranteed from -55C to +100C, measured in a 50Ω system.
Parameter
LO
RF
IF
Min
Typ
Max
14
(GHz)
(GHz)
(GHz)
Conversion Loss (dB)
1.0 – 13.0
1.0 – 13.0
0.5 – 2.0
2.0 – 8.5
9.5
11.5
+8
LO Drive Level (dBm)
LO Leakage (dBm)
LO-RF
+3
+15
1.0 – 13.0
1.0 – 13.0
1.0 – 13.0
See
Plots
LO-IF
1.0 – 13.0
1.0 – 13.0
RF-IF Isolation (dB)
Input 0.1 dB Compression (dBm)
1.0 – 13.0
1.0 – 13.0
See Plot
+13
1.0 – 13.0
1.0 – 13.0
See
Plot
Input Two-Tone Third Order
Intercept Point (dBm)
1.0 – 13.0
Bias Requirements (mA)
+6.0VB/+7.0VC
80
120
150
Part Number Options
Model Number
MT3A-0113HPA
MT3A-0113HCH-2
Description
Connectorized Package
Bare Die
Export Classification
EAR99
EAR99
Marki Microwave reserves the right to make changes to the product(s) or information contained herein without notice. Marki Microwave makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Marki Microwave assume any liability
whatsoever arising out of the use of or application of any product.
215 Vineyard Court, Morgan Hill, CA 95037 | Ph: 408.778.4200 | Fax 408.778.4300 | info@markimicrowave.com
Copyright © [2020] Marki Microwave, Inc. All Rights Reserved.
MT3A-0113H
TWO-TONE-TERMINATOR MIXER/LO AMPLIFIER
Page 2
LO/RF 1 GHz to 13 GHz
IF 0.5 GHz to 8.5 GHz
Typical Performance
Conversion Loss vs LO Power (dB)
Relative IF Response (dB)
-6
-8
0
-2
2GHz RF
12GHz RF
-10
-12
-14
-16
-18
-20
-4
-6
+3dBm
+9dBm
+0dBm
+6dBm
-8
+12dBm
+15dBm
-10
0
1
1
1
3
6
9
12
15
13
13
13
0
1
1
0
2
4
6
8
10
13
13
IF Frequency (GHz)
RF Frequency (GHz)
Input IP3 vs LO Power (dBm)
Output IP3 vs LO Power (dBm)
40
35
30
25
20
15
10
5
35
30
25
20
15
10
5
+6dBm
+12dBm
+9dBm
+6dBm
+9dBm
0
+15dBm
+12dBm
+15dBm
0
-5
3
3
3
5
7
9
11
3
5
7
9
11
RF Frequency (GHz)
RF Frequency (GHz)
LO Return Loss (dB)
RF Return Loss (dB)
0
-5
0
-5
-10
-15
-20
-25
-30
-35
-40
-10
-15
-20
-25
-30
-35
-40
5
7
9
11
3
5
7
9
11
RF Frequency (GHz)
LO Frequency (GHz)
IF Return Loss (dB)
RF to IF Isolation (dB)
0
-10
-20
-30
-40
-50
-60
0
-5
2GHz RF
12GHz RF
-10
-15
-20
-25
-30
-35
-40
5
7
9
11
2
4
6
8
10
RF Frequency (GHz)
IF Frequency (GHz)
Copyright © [2020] Marki Microwave, Inc. All Rights Reserved.
MT3A-0113H
TWO-TONE-TERMINATOR MIXER
Page 3
LO/RF 1 GHz to 13 GHz
IF 0.5 GHz to 8.5 GHz
Typical Performance
LO to IF Leakage vs LO Power (dBm)
LO to RF Leakage vs LO Power (dBm)
+15dBm +12dBm +9dBm
10
0
10
0
15dBm
+12dBm
+9dBm
+6dBm
+6dBm
-10
-20
-30
-40
-10
-20
-30
-40
1
1
1
1
3
5
7
9
11
13
1
1
1
1
3
5
7
9
11
13
LO Frequency (GHz)
LO Frequency (GHz)
Even LO Harmonic to RF Leakage (dBm)
Even LO Harmonic to IF Leakage (dBm)
0
-10
-20
-30
-40
-50
0
-10
-20
-30
-40
-50
2xLO
4xLO
2xLO
4xLO
3
3
3
5
7
9
11
13
3
3
3
5
7
9
11
13
LO Frequency (GHz)
LO Frequency (GHz)
Odd LO Harmonic to RF Leakage (dBm)
Odd LO Harmonic to IF Leakage (dBm)
0
-10
-20
-30
-40
-50
0
-10
-20
-30
-40
-50
3xLO
5xLO
3xLO
5xLO
5
7
9
11
13
5
7
9
11
13
LO Frequency (GHz)
LO Frequency (GHz)
2RF x 2LO Spurious Supression (dBc)
2IF x 1LO Spurious Supression (dBc)
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
5
7
9
11
13
5
7
9
11
13
RF Frequency (GHz)
RF Frequency (GHz)
Copyright © [2020] Marki Microwave, Inc. All Rights Reserved.
MT3A-0113H
TWO-TONE-TERMINATOR MIXER
Page 4
LO/RF 1 GHz to 13 GHz
IF 0.5 GHz to 8.5 GHz
Upconversion Spurious Suppression
Spurious data is taken by mixing a 1 GHz IF with LO frequencies (+mLO+nIF), which creates an RF within the 1 GHz to
13 GHz RF band. The mixer is swept across the full spurious output band and the mean is calculated. The numbers
shown in the table below are for a -10 dBm IF input. Spurious suppression is scaled for different IF input power levels by
(n-1), where “n” is the IF spur order. For example, the 2IFx1LO spur is typically 66 dBc for a -10 dBm input, so a -20
dBm IF input creates a spur that is (2-1) x (-10 dB) dB lower, or 76 dBc.
Typical Upconversion Spurious Suppression (dBc): +12 dBm Sine Wave LO Input
-10 dBm RF Input
0xLO
-------------
29
1xLO
2xLO
3xLO
4xLO
5xLO
0xIF
1xIF
2xIF
3xIF
4xIF
5xIF
See LO to RF Isolation and LO Harmonic to RF Isolation Plots (Page 3)
Reference
66
20
64
17
41
17
65
21
64
65
102
81
57
80
84
83
122
112
113
127
112
127
112
128
111
128
147
132
Downconversion Spurious Suppression
Spurious data is taken by selecting RF and LO frequencies (+mLO+nRF) within the 1 GHz to 13 GHz RF/LO bands,
which create a 1 GHz IF spurious output. The mixer is swept across the full spurious band and the mean is calculated.
The numbers shown in the table below are for a -10 dBm RF input. Spurious suppression is scaled for different RF
power levels by (n-1), where “n” is the RF spur order. For example, the 2RFx2LO spur is 63 dBc for a -10 dBm input, so
a -20 dBm RF input creates a spur that is (2-1) x (-10 dB) dB lower, or 73 dBc.
Typical Downconversion Spurious Suppression (dBc): +12 dBm Sine Wave LO Input
-10 dBm RF Input
0xRF
0xLO
-------------
23
1xLO
2xLO
3xLO
4xLO
5xLO
See LO to IF Isolation and LO Harmonic to IF Isolation Plots (Page 3)
1xRF
Reference
63
20
67
16
41
17
63
25
53
2xRF
71
3xRF
91
80
56
78
75
73
4xRF
118
109
112
129
109
123
108
124
100
119
5xRF
129
124
Copyright © [2020] Marki Microwave, Inc. All Rights Reserved.
MT3A-0113H
TWO-TONE-TERMINATOR MIXER
Page 5
LO/RF 1 GHz to 13 GHz
IF 0.5 GHz to 8.5 GHz
Recommended Operating Conditions
The Recommended Operating Conditions indicate the limits, inside which the device should be operated, to guarantee the
performance given in Electrical Specifications Operating outside these limits may not necessarily cause damage to the device,
but the performance may degrade outside the limits of the electrical specifications. For limits, above which damage may occur,
see Absolute Maximum Ratings.
Parameter
Min
Nominal
Max
Units
TA, Ambient Temperature
Positive DC Voltage (VC)
Quiescent DC Current (Ic)
DC Current with RF Input (Ic)
-40
+5
26
-
+25
+7
44
-
+85
+8
°C
V
65
mA
mA
V
150
+8
Positive DC Current Mirror Voltage (VB)
Input Power for Saturation
+5
-
+6
+10
+16
dBm
Absolute Maximum Ratings
The Absolute Maximum Ratings indicate limits beyond which damage may occur to the device. If these limits are exceeded,
the device may become inoperable or have a reduced lifetime
Absolute Maximum Ratings
Parameter
Maximum Rating
+8V
DC Voltage on VB or VC
DC Bias Current
150mA
RF Power Handling
LO Power Handling
Operating Temperature
Storage Temperature
+27dBm
+27dBm
-55ºC to +85ºC
65ºC to +125ºC
TBD ºC/W
TBD ºC
θJC, Junction to Case Thermal Resistance
Max Junction Temperature for MTTF> 1E6 hours
Max Power Dissipation for MTTF of 1E6 hours at 85˚C Baseplate
TBD mW
Temperature
ESD Sensitivity (HBM)
TBD
Copyright © [2020] Marki Microwave, Inc. All Rights Reserved.
MT3A-0113H
TWO-TONE-TERMINATOR MIXER
Page 6
LO/RF 1 GHz to 13 GHz
IF 0.5 GHz to 8.5 GHz
Connectorized Outline Drawing
Bare Die Outline Drawing
Copyright © [2020] Marki Microwave, Inc. All Rights Reserved.
MT3A-0113H
TWO-TONE-TERMINATOR MIXER
Page 7
LO/RF 1 GHz to 13 GHz
IF 0.5 GHz to 8.5 GHz
T3
I
Sine Wave
Amplifier
Square Wave
L
R
LO
RF
+V
IF
See T3 Mixer Primer for benefits of square wave LO drive
Port
Description
DC Interface Schematic
LO
The LO port is DC blocked and AC matched to 50 Ohms from 1 GHz to
13 GHz.
LO
1 uF
RF
RF
IF
The RF port is DC short to ground and AC matched to 50 Ohms from 1
GHz to 13 GHz. Blocking capacitor is optional.
The IF port is DC blocked and AC matched to 50 Ohms from 500 MHz
to 8.5 GHz.
IF
2 uF
VC
Port VC is the DC voltage supply for that supplies the amplifier’s
collector current. It is connected internally through the amplifier die’s RF
output port.
VC
VB
Port VB is the DC voltage bias for the current mirror that controls
collector current supplied to the amplifier. Larger voltages result in a
higher current draw through port VC, effectively functioning as a gain
control pin of the amplifier
VB
CH package ground path is provided through the substrate and ground
bond pads. PA package ground provided through metal housing and
outer coax conductor.
GND
Copyright © [2020] Marki Microwave, Inc. All Rights Reserved.
MT3A-0113H
TWO-TONE-TERMINATOR MIXER
Page 8
LO/RF 1 GHz to 13 GHz
IF 0.5 GHz to 8.5 GHz
Revision Code
Revision Date
Comment
_
Datasheet Initial Release
11/10/2020
Connector changed from
2.92mm to SMA
A
11/17/2020
DATA SHEET NOTES:
1. Mixer Conversion Loss Plot IF frequency is 1 GHz and LO power is +12dBm.
2. Mixer Noise Figure typically measures within 0.5 dB of conversion loss for IF frequencies greater than 5 MHz.
3. Conversion Loss typically degrades less than 0.5 dB at +100°C and improves less than 0.5 dB at -55°C.
4. There are no sequencing requirement for powering the integrated LO driver amplifier on or off.
5. Specifications are subject to change without notice. Contact Marki Microwave for the most recent specifications and data sheets.
6. Catalog mixer circuits are continually improved. Configuration control requires custom mixer model numbers and specifications.
Marki Microwave reserves the right to make changes to the product(s) or information contained herein without notice. Marki Microwave makes no
warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Marki Microwave assume any
liability whatsoever arising out of the use or application of any product.
215 Vineyard Court, Morgan Hill, CA 95037 | Ph: 408.778.4200 | Fax 408.778.4300 | sales@markimicrowave.com
www.markimicrowave.com
Copyright © [2020] Marki Microwave, Inc. All Rights Reserved.
相关型号：
MT3A-0505SI
All specifications are typical at nominal input, full load and 25ºC otherwise noted
VOLGEN
MT3A-0512SI
All specifications are typical at nominal input, full load and 25ºC otherwise noted
VOLGEN
MT3A-0512WI
All specifications are typical at nominal input, full load and 25ºC otherwise noted
VOLGEN
MT3A-0515WI
All specifications are typical at nominal input, full load and 25ºC otherwise noted
VOLGEN
MT3A-0533SI
All specifications are typical at nominal input, full load and 25ºC otherwise noted
VOLGEN
MT3A-1205SI
All specifications are typical at nominal input, full load and 25ºC otherwise noted
VOLGEN
MT3A-1212SI
All specifications are typical at nominal input, full load and 25ºC otherwise noted
VOLGEN
MT3A-1212WI
All specifications are typical at nominal input, full load and 25ºC otherwise noted
VOLGEN
MT3A-1215WI
All specifications are typical at nominal input, full load and 25ºC otherwise noted
VOLGEN
MT3A-1233SI
All specifications are typical at nominal input, full load and 25ºC otherwise noted
VOLGEN
©2020 ICPDF网 联系我们和版权申明