MAX11503EVKIT+ [MAXIM]
Surface-Mount Construction;型号: | MAX11503EVKIT+ |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | Surface-Mount Construction |
文件: | 总6页 (文件大小:112K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-4027; Rev 0; 2/08
MAX11503 Evaluation Kit
Evluates:MAX1503
General Description
Features
♦ 2.7V to 5.25V Operating Range
♦ DC- or AC-Coupled Input
The MAX11503 evaluation kit (EV kit) is a fully assem-
bled and tested surface-mount printed-circuit board
(PCB). The MAX11503 EV kit evaluates the MAX11503
IC, a video amplifier with Y/C summer and chroma
mute. The MAX11503 operates at 3V (typ) and drives
two terminated 75Ω loads at an overall gain of +6dB.
♦ DC- or AC-Coupled Output
♦ Surface-Mount Construction
♦ Fully Assembled and Tested
Component List
Ordering Information
DESIGNATION QTY
DESCRIPTION
PART
TYPE
MAX11503EVKIT+
EV Kit
10µF 20ꢀ, 6.3V X7R ceramic
capacitor (0805)
Murata GRM21BR70J106K
TDK C2012X7R0J106K or equivalent
+Denotes lead-free and RoHS-compliant.
C1
1
0.1µF 10ꢀ, 16V X7R ceramic
capacitors (0603)
C2, C3, C4
C5, C6
3
Murata GRM188R71C104K
TDK C1608X7R1C104KT or
equivalent
Not installed, aluminum electrolytic
capacitors (6.3mm x 6mm)
0
3
C_IN, OUT,
Y_IN
75Ω BNC PCB-mount jack
connectors
JU1, JU2
JU3, JU4
R1, R2, R3
R5, R6
2
2
3
2
3-pin headers
2-pin headers
75Ω
1ꢀ resistors (0603)
0Ω resistors (0603)
®
Video filter amplifier (8-pin µMAX )
Maxim MAX11503EUA+
U1
1
—
—
4
1
Shunts
PCB: MAX11503 Evaluation Kit+
µMAX is a registered trademark of Maxim Integrated Products, Inc.
Component Suppliers
SUPPLER
Murata Mfg. Co., Ltd.
TDK Corp.
PHONE
WEBSITE
770-436-1300
847-803-6100
www.murata.com
www.component.tdk.com
Note: Indicate that you are using the MAX11503 when contacting these component suppliers.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim's website at www.maxim-ic.com.
MAX11503 Evaluation Kit
Jumper Selection
The EV kit incorporates jumper JU1 to control the
PSAVE pin. The PSAVE pin puts the device into a low-
power mode. See Table 1 for jumper JU1 settings.
Quick Start
Recommended Equipment
Before beginning, the following equipment is needed:
• 3V DC power supply
Table 1. Jumper JU1 Settings
• Video signal generator (e.g., Tektronix TG2000 or
similar)
SHUNT
POSITION
PSAVE PIN
MAX11503 OUTPUT
• Video measurement equipment (e.g., Tektronix
VM700A or similar)
1-2*
2-3
Connected to VCC
Connected to GND
Enabled
Disabled
Procedure
*Default position.
The MAX11503 EV kit is a fully assembled and tested
surface-mount PCB. Follow the steps below to verify
board operation. Caution: Do not turn on the power
supply until all connections are completed.
1) Verify that a shunt is installed across pins 1-2 of
jumper JU1 (power-up).
The EV kit incorporates jumper JU2 to control the
CMUTE pin. The CMUTE pin provides options to enable
or disable the chroma input signal from the summer.
See Table 2 for jumper JU2 settings.
2) Verify that a shunt is installed across pins 2-3 of
jumper JU2 (summer is enabled).
Table 2. Jumper JU2 Settings
SHUNT
POSITION
CMUTE PIN
MAX11503 OUTPUT
3) Connect the output of the video signal generator to
the Y_IN (luma) and C_IN (chroma) BNC connectors
on the EV kit.
Evluates:MAX1503
1-2
Connected to VCC
Connected to GND
Y (luma) signal
Composite CVBS
signal
4) Connect the composite CVBS video output signal
from the OUT BNC connector on the EV kit to the
input of the video measurement equipment.
2-3*
*Default position.
5) Connect a 3V supply to the VCC pad. Connect the
supply ground to the GND pad.
Input Signals
The MAX11503 accepts either DC- or AC-coupled luma
input signals that are selected with jumpers JU3 and
JU4, as shown in Table 3. The MAX11503 is configured
for AC-coupled inputs by default. When using DC-cou-
pled inputs, make sure that the luma input signal has a
sync tip near ground.
6) Set the video signal generator for the desired video
input signals. This signal must contain sync informa-
tion (i.e., composite or Y).
7) Turn on the power supply and enable the video sig-
nal generator.
8) Analyze the output signal with the VM700A video
measurement equipment.
Table 3. Jumper JU3, JU4 Settings
SHUNT POSITION
Installed
MAX11503 INPUT
DC-coupled
Detailed Description
The MAX11503 EV kit evaluates the MAX11503 3V
operation video amplifier with Y/C summer and a chro-
ma mute that can drive two terminated 75Ω video
loads. The MAX11503 EV kit accepts AC-coupled Y
(luma) and C (chroma) input signals summing them into
a composite CVBS output signal with gain of +6dB.
Not installed*
AC-coupled
*Default position.
Output Signal
The MAX11503 EV kit can provide a sag-corrected DC-
or AC-coupled composite CVBS or Y (luma) signal. The
default output signal is set as DC-coupled composite
CVBS. To change the output signal to sag-corrected
AC-coupled, remove the R5 and R6 0Ω resistors and
install a 68µF and a 22µF aluminum electrolytic capaci-
tor on the C5 and C6 pads, respectively.
2
_______________________________________________________________________________________
MAX11503 Evaluation Kit
Evluates:MAX1503
Figure 1. MAX11503 EV Kit Schematic
_______________________________________________________________________________________
3
MAX11503 Evaluation Kit
Evluates:MAX1503
Figure 2. MAX11503 EV Kit Component Placement Guide—Top Silkscreen
4
_______________________________________________________________________________________
MAX11503 Evaluation Kit
Evluates:MAX1503
Figure 3. MAX11503 EV Kit PCB Layout—Component Side
_______________________________________________________________________________________
5
MAX11503 Evaluation Kit
Evluates:MAX1503
Figure 4. MAX11503 EV Kit PCB Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
6 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2008 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
Boblet
相关型号:
©2020 ICPDF网 联系我们和版权申明