MAX15022EVKIT [MAXIM]
Independent Enable Inputs for All Outputs;
| 型号： | MAX15022EVKIT |
| 厂家： | 
MAXIM INTEGRATED PRODUCTS |
| 描述： | Independent Enable Inputs for All Outputs |
| 文件： | 总10页 (文件大小：251K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
19-4101; Rev 0; 5/08
MAX15022 Evaluation Kit
Evluates:MAX1502
General Description
Features
The MAX15022 evaluation kit (EV kit) circuit demon-
strates the MAX15022 IC, which integrates two high-
performance PWM switching step-down regulators and
two low-dropout (LDO) controllers. Each controller and
regulator features independent enable controls for
power-up sequence operation. The EV kit is designed
to operate from a single 4.5V to 5.5V DC power supply.
o 4.5V to 5.5V Input Range
o Regulator Outputs
3.3V at 4A
1.5V at 2A
o 2MHz Switching Frequency
o LDO Outputs
The synchronous step-down outputs provide 3.3V/4A
and 1.5V/2A, and can be configured for power-up
sequencing or tracking operation. The converter
switching frequency is set to 2MHz and operates 180°
out-of-phase, reducing input voltage ripple and total
RMS input ripple current. The LDO outputs provide
2.5V and 1.2V, at up to 500mA each. Each LDO con-
troller is powered from either the input power source or
one of the regulator outputs.
2.5V (Up to 500mA)
1.2V (Up to 500mA)
o Independent Enable Inputs for All Outputs
o Configurable Power-Up Sequencing for Outputs
o Configurable Power-Up Tracking for Regulators
(VOUT1, VOUT2)
o Thermal Shutdown and Hiccup-Mode Short-
Circuit Protection
Ordering Information
o Fully Assembled and Tested
PART
TYPE
MAX15022EVKIT+
EV Kit
+Denotes lead-free and RoHS-compliant.
Component List
DESIGNATION QTY
DESCRIPTION
DESIGNATION QTY
DESCRIPTION
150µF 20ꢀ, 10V aluminum
electrolytic capacitor
(6.6mm x 6.6mm)
68pF 5ꢀ, 50V C0G ceramic
capacitor (0603)
Murata GRM1885C1H680J
C15
C17
1
1
C1
1
Panasonic EEEFK1A151P
270pF 5ꢀ, 50V C0G ceramic
capacitor (0603)
Murata GRM1885C1H271J
0.1µF 10ꢀ, 16V X7R ceramic
capacitors (0603)
Murata GRM188R71C104K
C2, C4, C9,
C10, C14, C18
6
6
1
1
1µF 10ꢀ, 10V X7R ceramic
capacitors (0805)
TDK C2012X7R1A105K
C20, C22
C25, C26
C27, C28
2
0
2
10µF 10ꢀ, 6.3V X7R ceramic
capacitors (0805)
Murata GRM21BR70J106K
C3, C8, C11,
C12, C19, C21
Not installed, ceramic capacitors
(0603)
180pF 5ꢀ, 50V C0G ceramic
capacitor (0603)
Murata GRM1885C1H181J
C5
C6
2200pF 10ꢀ, 16V X7R ceramic
capacitors (0603)
Murata GRM188R71C222K
390pF 5ꢀ, 50V C0G ceramic
capacitor (0603)
Murata GRM1885C1H391J
JU1–JU4
L1
4
1
3-pin headers
0.47µH, 5A inductor
Vishay IHLP-1616BZ-ER-R47-M-01
10pF 5ꢀ, 50V C0G ceramic
capacitors (0603)
Murata GRM1885C1H100J
C7, C16
2
0
1µH, 4A inductor
Vishay IHLP-1616BZ-ER-1R0-M-01
L2
1
C13, C23, C24
Not installed, capacitors (0805)
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX15022 Evaluation Kit
Component List (continued)
DESIGNATION QTY
DESCRIPTION
DESIGNATION QTY
DESCRIPTION
R16
R17, R21
R20
1
2
1
1
1
1
1
0
1kΩ 1ꢀ resistor (0603)
-20V, 1.5A pnp transistors
(SOT223-4)
Fairchild Semiconductor BCP69
Q1, Q2
2
15kΩ 1ꢀ resistors (0603)
2.55kΩ 1ꢀ resistor (0603)
47.5kΩ 1ꢀ resistor (0603)
10.5kΩ 1ꢀ resistor (0603)
18.2kΩ 1ꢀ resistor (0603)
10kΩ 1ꢀ resistor (0603)
Not installed, resistors (1206)
R1, R7
2
1
1
1
1
3
1
1
1
2
3
120Ω 5ꢀ resistors (0603)
100Ω 1ꢀ resistor (0603)
23.7kΩ 1ꢀ resistor (0603)
7.5kΩ 1ꢀ resistor (0603)
15.8kΩ 1ꢀ resistor (0603)
11.5kΩ 1ꢀ resistors (0603)
1.5kΩ 1ꢀ resistor (0603)
18.7kΩ 1ꢀ resistor (0603)
15Ω 1ꢀ resistor (0603)
R22
R2
R3
R23
R25
R4
R26
R5
R27, R28
R6, R9, R10
R11
Dual regulator/LDO controller
(28 TQFN-EP*)
Maxim MAX15022ATI+
U1
1
R12
—
—
4
1
Shunts (JU1–JU4)
R13
PCB: MAX15022 Evaluation Kit+
R14, R18
R15, R19, R24
24.9kΩ 1ꢀ resistors (0603)
16.5kΩ 1ꢀ resistors (0603)
*EP = Exposed pad.
Evluates:MAX1502
Component Suppliers
SUPPLIER
PHONE
WEBSITE
Fairchild Semiconductor
Murata Electronics North America, Inc.
Panasonic Corp.
888-522-5372
770-436-1300
714-373-7366
847-803-6100
203-268-6261
www.fairchildsemi.com
www.murata-northamerica.com
www.panasonic.com
TDK Corp.
www.component.tdk.com
www.vishay.com
Vishay
Note: Indicate that you are using the MAX15022 when contacting these component suppliers.
2) Install shunts across pins 1-2 of jumpers JU3
Quick Start
Required Equipment
Before beginning, the following equipment is needed:
(VOUT2 sequences after VOUT1) and JU4
(sequencing mode for outputs VOUT1, VOUT2).
3) Connect the voltmeter positive-terminal inputs to the
VOUT1–VOUT4 PCB pads.
•
•
Adjustable 4.5V to 5.5V, 5A DC power supply
Four voltmeters
4) Connect the voltmeter negative-terminal inputs to
the respective output’s PGND PCB pads.
Procedure
5) Connect a DC power supply to the VIN and PGND
pads and set the voltage to 5V.
The MAX15022 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed.
6) Enable the power-supply output.
7) Verify that the voltmeters at VOUT1–VOUT4 mea-
sure 3.3V, 1.5V, 2.5V, and 1.2V, respectively.
1) Install shunts across pins 2-3 of jumpers JU1
(VOUT1 input source for VOUT3) and JU2 (VOUT2
input source for VOUT4).
2
_______________________________________________________________________________________
MAX15022 Evaluation Kit
Evluates:MAX1502
The MAX15022 IC operates with either regulator output
as the master or slave during tracking mode. However,
the MAX15022 EV kit is designed with VOUT1 as the
master and VOUT2 as the slave during tracking opera-
tion. See Table 1 for jumpers JU3 and JU4 configura-
tion for operating the EV kit step-down regulators in
tracking or sequencing mode.
Detailed Description of Hardware
The MAX15022 EV kit circuit demonstrates the
MAX15022 IC, which integrates two high-performance
PWM switching synchronous step-down regulators and
two LDO controllers. The EV kit regulator outputs can
be configured for sequencing, ratiometric-tracking, or
coincident-tracking mode. The MAX15022 IC operates
with either step-down regulator outputs as the master;
however, the EV kit is designed with VOUT1 as the
master during tracking operation. Each controller and
regulator features independent enable controls for
power-up sequencing operation. The EV kit is designed
to operate from a single DC power supply that provides
4.5V to 5.5V and 5A of current.
Table 1. VOUT1/VOUT2 Tracking/
Sequencing Operation (JU3, JU4)
SHUNT
POSITION
EV KIT CIRCUIT
MODIFICATION
EV KIT VOUT1/VOUT2
OPERATION
JU3
JU4
1-2
1-2
—
—
Sequence mode
The EV kit’s dual step-down regulator’s outputs (VOUT1
and VOUT2) are configured for 3.3V and 1.5V, providing
up to 4A and 2A, respectively. The regulator’s tracking
sequencing operation modes are selectable through
jumpers JU3 and JU4. The switching frequency is set to
2MHz by resistor R24 and can be programmed from
500kHz to 4MHz. The outputs operate 180° out-of-
phase to reduce input voltage ripple and total RMS
input ripple current.
Coincident-tracking mode
(VOUT1 master, VOUT2
slave)
2-3
2-3
2-3
2-3
Ratiometric-tracking
mode (VOUT1 master,
VOUT2 slave)
Resistor R14 must
be removed
The LDO outputs (VOUT3 and VOUT4) are configured
for 2.5V and 1.2V, respectively, and provide up to
500mA each. Jumpers JU1 and JU2 select the LDO’s
input power source or configure VOUT3 and VOUT4 for
power-supply sequencing to the regulator outputs,
VOUT1 and VOUT2, respectively.
The EV kit’s VOUT1 and VOUT2 outputs are configured
for coincident-tracking operation by default. VOUT2
output voltage ramps up, tracking the VOUT1 voltage
using resistor pairs R14/R15 and R18/R19, which sets
the resistor-divider ratios. Place shunts across pins 2-3
of jumpers JU3 and JU4 to operate VOUT1 and VOUT2
in coincident tracking mode.
Input Power Source
The MAX15022 EV kit regulator outputs (VOUT1 and
VOUT2) are optimized to provide up to 4A and 2A,
respectively, when operating with an input-voltage
source of 4.5V to 5.5V. The EV kit accommodates input
voltages down to 2.35V; however, each output rail’s
passive filtering, enabling, and compensation circuitry
needs to be revisited to confirm optimal performance.
Additionally, VOUT1’s 3.3V rail likely needs to be read-
justed to a lower-than-VIN potential. Refer to the
MAX15022 IC data sheet for additional information on
the minimum voltage requirements, as well as the PWM
Controllers Design Procedure and LDO Controllers
Design Procedure sections.
In ratiometric-tracking mode, VOUT1 and VOUT2 soft-
start controllers are synchonized, and hence, their
respective output voltages track ratiometrically. For
ratiometric-tracking operation, the EV kit PCB requires a
minor modification. Place shunts across pins 2-3 of
jumpers JU3 and JU4 and remove resistor R14 for ratio-
metric-tracking mode.
When operating the EV kit in sequencing mode, each
regulator operates independently with its own enable
input. To operate regulator outputs VOUT1 and VOUT2
in sequencing mode, install shunts across pins 1-2 of
jumpers JU3 and JU4. The VOUT2 output does not turn
on until VOUT1 rises above the EN2 1.22V threshold.
Refer to the Tracking/Sequencing section in the
MAX15022 IC data sheet for additional information on
operating in coincident/ratiometric-tracking and
sequencing modes, and to calculate the proper values
for resistor pairs R14/R15 and R18/R19.
Regulator's Power Tracking/Sequencing
The MAX15022 EV kit can be configured to power up
and power down the VOUT1 and VOUT2 outputs in
sequencing, ratiometric-tracking, or coincident-
tracking mode by configuring jumpers JU3 and JU4.
_______________________________________________________________________________________
3
MAX15022 Evaluation Kit
VOUT3 current capability is restricted by the regulator’s
input power source, the output voltage setting, and
transistor Q1. Verify that Q1 power dissipation rating is
not exceeded when operating the LDO regulator at
high input-to-output voltage differentials and full load.
Step-Down Regulator Output Voltages
(VOUT1, VOUT2)
Regulator output VOUT1 is set to 3.3V with resistors
R22 and R23 and provides up to 4A at 90ꢀ efficiency.
Capacitors C15, C16, and C17, and resistors R18 and
R19 provide a compensation network for VOUT1 on the
EV kit.
1.2V Regulator Output (VOUT4)
VOUT4 LDO output is set to 1.2V by feedback resistors
R9 and R10 and provides up to 500mA of output cur-
rent. Jumper JU2 selects the input power source for
VOUT4 or configures VOUT4 for power-supply
sequencing with VOUT2. Install a shunt across pins 1-2
to select VIN as the input power source. Install a shunt
across pins 2-3 to select VOUT2 as the LDO input
power source. Resistors R11 and R12 set the VOUT4
turn-on threshold to 1.3V. See Table 3 for proper
jumper configuration of VOUT4 input power source.
Regulator output VOUT2 is set to 1.5V with resistors
R18 and R19 and provides up to 2A at 84ꢀ efficiency.
Capacitors C5, C6, and C7, and resistors R16 and
R17 provide a compensation network for VOUT2 on
the EV kit.
VOUT1 and VOUT2 output voltages can be reconfig-
ured between 0.6V to VIN by replacing the respective
feedback resistors. To reconfigure the regulator out-
puts, refer to the Compensation Design Guidelines sec-
tion in the MAX15022 IC data sheet for instructions on
selecting new resistor values. Also refer to the Effective
Input-Voltage Range section in the MAX15022 IC data
sheet for the minimum and maximum input-voltage
range when reconfiguring the regulator outputs.
Table 3. VOUT4 Input Power Source (JU2)
SHUNT
VOUT4 INPUT
EV KIT OPERATION
POSITION POWER SOURCE
Evluates:MAX1502
1-2
2-3
VIN
VOUT4 enabled
VOUT4 enabled
Component changes are necessary for proper opera-
tion after reconfiguring the output voltage. Refer to the
Inductor Selection, Input-Capacitor Selection, and the
Compensation Design Guidelines sections in the
MAX15022 IC data sheet to select the proper values.
VOUT2
Not
installed
—
VOUT4 disabled
2.5V LDO Output (VOUT3)
The VOUT3 LDO output is set to 2.5V by feedback
resistors R3 and R4 and provide up to 500mA of output
current. Jumper JU1 selects the input power source for
VOUT3 or configures VOUT3 for power-supply
sequencing with VOUT1. Install a shunt across pins 1-2
to select VIN as the input power source. Install a shunt
across pins 2-3 to select VOUT1 as the LDO input
power source. Resistors R5 and R6 set VOUT3 turn-on
threshold to 3V. See Table 2 for proper jumper configu-
ration of VOUT3 input power source.
To reconfigure VOUT4 to different output voltages, refer
to the Output 3 and Output 4 Voltage Selection section in
the MAX15022 IC data sheet for additional information.
VOUT4 current capability is restricted by the regulator’s
input power source, the output voltage setting, and
transistor Q2. Verify that Q2 power dissipation rating is
not exceeded when operating the LDO regulator at
high input-to-output voltage differentials and full load.
Switching Frequency
The MAX15022 switching frequency is set to 2MHz by
resistor R24. Replace resistor R24 with a new resistor
value to program the switching frequency between
500kHz and 4MHz. Use the following equation to select
R24 when reconfiguring the switching frequency:
Table 2. VOUT3 Input Power Source (JU1)
SHUNT
VOUT3 INPUT
EV KIT OPERATION
POSITION POWER SOURCE
−3
R24 ≅ (8.36 ×10 ) × f
1-2
2-3
VIN
VOUT3 enabled
VOUT3 enabled
SW
VOUT1
where f
is in hertz and R24 is in ohms.
SW
Not
installed
When reconfiguring the EV kit switching frequency, it is
necessary to replace the compensation network and
power components. Refer to the Inductor Selection and
Compensation Design Guidelines sections in the
MAX15022 IC data sheet for computing new compen-
sation and power component values.
—
VOUT3 disabled
To reconfigure VOUT3 to different output voltages, refer
to the Output 3 and Output 4 Voltage Selection section in
the MAX15022 IC data sheet for additional information.
4
_______________________________________________________________________________________
MAX15022 Evaluation Kit
Evluates:MAX1502
Figure 1. MAX15022 EV Kit Schematic
_______________________________________________________________________________________
5
MAX15022 Evaluation Kit
Evluates:MAX1502
Figure 2. MAX15022 EV Kit Component Placement Guide—Component Side
6
_______________________________________________________________________________________
MAX15022 Evaluation Kit
Evluates:MAX1502
Figure 3. MAX15022 EV Kit PCB Layout—Component Side
_______________________________________________________________________________________
7
MAX15022 Evaluation Kit
Evluates:MAX1502
Figure 4. MAX15022 EV Kit PCB Layout—GND Layer 2
8
_______________________________________________________________________________________
MAX15022 Evaluation Kit
Evluates:MAX1502
Figure 5. MAX15022 EV Kit PCB Layout—Inner Trace Layer 3
_______________________________________________________________________________________
9
MAX15022 Evaluation Kit
Evluates:MAX1502
Figure 6. MAX15022 EV Kit PCB Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
10 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2008 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
相关型号：
©2020 ICPDF网 联系我们和版权申明