MAX1531EVKIT [MAXIM]
fully assembled and tested surface-mount circuit board;
| 型号： | MAX1531EVKIT |
| 厂家： | 
MAXIM INTEGRATED PRODUCTS |
| 描述： | fully assembled and tested surface-mount circuit board |
| 文件： | 总13页 (文件大小：307K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
19-3520; Rev 0; 11/04
MAX1531 Evaluation Kit
General Description
Features
The MAX1531 evaluation kit (EV kit) is a fully assembled
and tested surface-mount circuit board that provides
logic and bias power required for liquid crystal display
(LCD) monitors. The EV kit contains a step-down
switching regulator, a logic-supply linear regulator, a
source-driver-supply linear regulator, a gamma-refer-
ence linear regulator, a two-stage positive charge
pump and linear regulator for the TFT gate-on supply,
and a one-stage negative charge pump and linear reg-
ulator for the TFT gate-off supply. The source-driver
supply, the gamma-reference supply, the gate-on sup-
ply, and the gate-off supply can be sequenced in any
power-up order. The EV kit also includes a MAX1522
step-up switching regulator to provide a higher output
voltage option for the source-driver supply and the
gamma reference.
♦ Output Voltages (Input Range = +10.5V to +24V or
+9.5V to +24V Using Included MAX1522 Circuit)
+3.3V Output at 1.5A (Step-Down Switching
Regulator)
+2.5V Output at 500mA (Logic-Supply
Regulator)
+10V Output at 500mA (Source-Driver Supply
Regulator)
+9.7V Output at 50mA (Gamma-Reference
Regulator)
+25V Output at 25mA (Positive Charge Pump
and Linear Regulator)
-9V Output at 50mA (Negative Charge Pump
and Linear Regulator)
♦ +8V to +24V Input Range (Reduced Output
Voltages)
The EV kit produces the output voltages listed in the
features column using a +10.5V to +24V input voltage
range. The input range can be reduced to +9.5V if the
included MAX1522 step-up regulator circuit is used. If
lower output voltages are acceptable, the input range
can be further reduced to +8V.
♦ Resistor-Adjustable Outputs
♦ 92% Efficiency (Step-Down Switching Regulator)
♦ 250kHz/500kHz Selectable Step-Down Switching
Frequency
♦ Programmable Power-Up Sequencing
♦ Soft-Start for All Outputs
The EV kit features undervoltage protection for the
input, overcurrent protection for the step-down switch-
ing regulator, and overload protection for the source-
drive linear regulator. Operation at 500kHz allows the
use of small surface-mount components. The EV kit
also evaluates the MAX1530.
♦ Multilevel Protection
Resistor-Adjustable Input Undervoltage
Threshold
Output Undervoltage Shutdown
Overcurrent Protection for One Linear
Regulator
Current Limit for the Step-Down Switching
Regulator
Component List
♦ External Step-Up Switching Regulator (MAX1522)
Included
DESIGNATION QTY
DESCRIPTION
♦ Also Evaluates the MAX1530 (IC Replacement
1µF 10%, 25V X7R ceramic
capacitors (0805)
Required)
C1, C4
C2, C23
C3
2
0
1
TDK C2012X7R1E105K
♦ Low-Profile, Surface-Mount Components
♦ Fully Assembled and Tested
Not installed capacitors (0603)
4.7µF 10%, 25V X7R ceramic
capacitor (1210)
TDK C3225X7R1E475K
Ordering Information
C5, C6, C8,
C11, C14, C15,
C17, C18, C20
0.1µF 10%, 50V X7R ceramic
capacitors (0603)
TDK C1608X7R1H104K
PART
TEMP RANGE
IC PACKAGE
9
1
MAX1531EVKIT
0°C to +70°C
32 TQFN (5mm x 5mm)
22µF 20%, 6.3V X7R ceramic
capacitor (1206)
C7
TDK C3216X7R0J226M
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
MAX1531 Evaluation Kit
Component List (continued)
DESIGNATION QTY
DESCRIPTION
DESIGNATION QTY
DESCRIPTION
10µF 20%, 6.3V X5R ceramic
capacitor (1206)
TDK C3216X5R0J106M
10µH, 2.3A
Sumida CDR7D28MN-100
inductor
DC
L1
L2
1
1
C9
C10
1
1
2
2
1
2
1
1
2
22µH, 0.90A inductor
Sumida CDRH5D28-220
DC
470pF 10%, 50V X7R ceramic
capacitor (0603)
TDK C1608X7R1H471K
2.5A, 30V dual n-channel MOSFET
(Super SOT-6)
Fairchild Semiconductor FDC6561AN
N1
N2
1
1
0.47µF 10%, 16V X7R ceramic
capacitors (0805)
TDK C2012X7R1C474K
C12, C19
C13, C25
C16
5.2A, 30V n-channel MOSFET (Super
SOT-6)
Fairchild Semiconductor FDC633N
4.7µF 10%, 16V X7R ceramic
capacitors (1206)
TDK C3216X7R1C475K
3A, 60V low-saturation pnp bipolar
transistors
(SOT-223)
Q1, Q4
2
0.47µF 20%, 50V X7R ceramic
capacitor (1210)
TDK C3225X7R1H474M
Fairchild Semiconductor NZT660A
200mA, 40V pnp bipolar transistors
(SOT23)
Central Semiconductor CMPT3906
Q2, Q3
Q5, Q6
2
2
2.2µF 10%, 25V X7R ceramic
capacitors (1206)
TDK C3216X7R1E225K
C21, C22
C24
200mA, 40V npn bipolar transistors
(SOT23)
Central Semiconductor CMPT3904
10µF 20%, 25V X5R ceramic
capacitor (1210)
TDK C3225X5R1E106M
R1
R2, R23
R3
1
2
1
1
17.8kΩ 1% resistor (0805)
10.7kΩ 1% resistors (0805)
124kΩ 1% resistor (0805)
20.0kΩ 1% resistor (0805)
1µF 10%, 10V X5R ceramic
capacitor (0603)
TDK C1608X5R1A105K
C26
R4
R5, R6, R7,
R11
100mA, 30V Schottky diodes (SOD-
523)
Central Semiconductor CMOSH-3
4
4
4
100kΩ 5% resistors (0805)
6.8kΩ 5% resistors (0805)
10.0kΩ 1% resistors (0805)
D1, D6
R8, R17, R24,
R27
1A, 30V Schottky diode (S-flat)
Toshiba CRS02
D2
1
3
R9, R10, R19,
R32
250mA, 100V dual diodes (SOT23)
Central Semiconductor CMPD6001S
D3, D4, D5
R12
R13
1
1
1
2
1
1
1
1
1
301kΩ 1% resistor (0805)
221kΩ 1% resistor (0805)
121kΩ 1% resistor (0805)
68.1kΩ 1% resistors (0805)
43.2kΩ 1% resistor (0805)
1.5kΩ 5% resistor (0805)
75.0kΩ 1% resistor (0805)
200kΩ 1% resistor (0805)
10.5kΩ 1% resistor (0805)
250mA, 75V high-speed silicon diode
(SOD-523)
Central Semiconductor CMOD4448
D7
1
6
R14
R15, R18
R16
JU1,
JU12–JU16
3-pin headers
R21
JU2, JU3
JU4–JU7
JU8–JU11
2
4
4
2-pin headers
R22
3-way jumpers (4 pins)
4-way jumpers (5 pins)
R25
R26
2
_______________________________________________________________________________________
MAX1531 Evaluation Kit
3) Verify that a shunt is across pins 1 and 3 of jumpers
JU4, JU5, JU6, JU7, and JU8.
Component List (continued)
DESIGNATION QTY
DESCRIPTION
90.9kΩ 1% resistor (0805)
48.7kΩ 1% resistor (0805)
1Ω 5% resistor (0805)
4) Verify that a shunt is across pins 1 and 5 of jumper
JU9.
R28
R29
R30
R31
1
1
1
1
5) Verify that a shunt is across pins 1 and 4 of jumper
JU11.
110kΩ 1% resistor (0805)
6) Verify that a shunt is across pins 2 and 3 of jumpers
JU13, JU14, JU15, and JU16.
0.050Ω 1% resistor (1206)
IRC LRC-LR 1206-01-R050-F
R33
1
7) Connect the positive terminal of the input power
supply to the PIN pad. Connect the negative termi-
nal of the input power supply to the PGND pad.
R34
R35, R36
R37, R38
R39–R42
U1
0
2
2
4
1
1
Not installed resistor (0805)
1.00Ω 1% resistors (0805)
10Ω 5% resistors (0805)
2.0kΩ 5% resistors (0805)
MAX1531ETJ (32-pin TQFN)
MAX1522EUT-T (6-pin SOT23)
8) Turn on the power supply and verify that the step-
down regulator output (VOUT) is +3.3V.
9) Verify that the internal 5V linear regulator output
(VL) is +5V.
U2
10) Verify that the logic-supply linear regulator output
(VLOG) is +2.5V.
None
16 Shunts (see table for jumper settings)
MAX1531 PC board
None
1
11) Verify that the source-driver-supply linear regulator
output (VSRC) is +10V.
Quick Start
12) Verify that the gamma-reference linear regulator
output (VGAM) is +9.7V.
The MAX1531 EV kit is fully assembled and tested.
Follow these steps to verify board operation. Do not
turn on the power supply until all connections are
completed.
13) Verify that the gate-on linear regulator output (GON)
is +25V.
14) Verify that the gate-off linear regulator output
(GOFF) is -9V.
The MAX1531 EV kit operates with up to +24V inputs.
However, due to external-component voltage stress limi-
tations, default jumper configurations must be modified
for operation above +13.2V. See the Positive Charge
Pump and Gate-On Linear Regulator Output Voltage
(GON) sections.
For instructions on selecting the feedback resistors for
other output voltages, see the Output Voltage Selection
section.
Detailed Description
Recommended Equipment
• +10.5V to +13.2V, 2A DC power supply
The MAX1531 EV kit contains a step-down switching
regulator, a linear regulator for a low-voltage logic sup-
ply, a high-current linear regulator for a source-driver
supply, a linear regulator for a gamma reference, a two-
stage positive charge pump with a positive high-volt-
age linear regulator, and a one-stage negative charge
pump with a negative linear regulator. The EV kit oper-
ates from a +10.5V and +24V DC power supply, which
• One voltmeter
1) Verify that a shunt is across pins 1 and 2 of jumpers
JU1, JU10, and JU12.
2) Verify that there are no shunts across jumpers JU2
and JU3.
Component Suppliers
SUPPLIER
PHONE
FAX
WEBSITE
www.centralsemi.com
Central Semiconductor
631-435-1110
888-522-5372
361-992-7900
847-545-6700
847-803-6100
949-455-2000
631-435-1824
—
Fairchild
IRC
www.fairchildsemi.com
www.irctt.com
361-992-3377
847-545-6720
847-390-4405
949-859-3963
Sumida
TDK
www.sumida.com
www.component.tdk.com
www.toshiba.com/taec
Toshiba
Note: Indicate you are using the MAX1530/MAX1531 when contacting these manufacturers.
_______________________________________________________________________________________
3
MAX1531 Evaluation Kit
can provide at least 2A. The step-down switching regu-
lator’s switching frequency is jumper configurable
between 250kHz and 500kHz. The adjustable input
undervoltage protection (EN) protects the EV kit from
undervoltage conditions. The step-up switching regula-
tor and the source-drive regulator are protected against
overloads.
age, which is the output of the negative charge pump
(see the Output Voltage Selection section).
The EV kit also features power-up sequencing. After EN
and SEQ go high, the logic voltage supply (VLOG) soft-
starts. The gamma reference, the gate-on supply, the
source-driver supply, and the gate-off supply can soft-
start in any sequence by setting the appropriate
jumpers (see the Power-Up Sequencing section).
The step-down switching regulator (VOUT) generates a
+3.3V output and can provide at least 1.5A. The step-
down switching-regulator output voltage can be adjust-
ed as low as +1.24V using different feedback resistors
(see the Output Voltage Selection section).
The EV kit includes a current-limit circuit for the step-
down switching regulator. The current-limit threshold is
set by resistor-dividers R12, R13, and the R
of
DS(on)
MOSFET N1 (refer to the MOSFET Selection and
Current-Limit Setting section in the MAX1531 data sheet
for further detail). The EV kit also includes current over-
load protection for the source-driver supply voltage. The
MAX1531 will shut down if the source-driver supply
exceeds a current threshold. The output current over-
load threshold is set by sense resistors R35 and R36
(refer to the Overcurrent Protection Block (CSH, CSL)
section in the MAX1531 data sheet for further detail).
The logic voltage supply (VLOG) is set to +2.5V using a
linear regulator controller and an external pnp bipolar
pass transistor. This logic voltage supply can provide at
least 500mA of current. The logic-voltage-supply linear
regulator’s output can be adjusted between +1.24V and
its input supply, which is the step-down regulator’s out-
put voltage (see the Output Voltage Selection section).
The source-driver supply (VSRC) is set to +10V using a
linear regulator controller and an external pnp bipolar
pass transistor. This source-driver supply can provide
at least 500mA of current. The source-drive linear regu-
lator’s output can be adjusted between +1.24V and its
input voltage, which is either the EV kit input voltage
(PIN) or the output of the MAX1522 step-up regulator,
depending on jumper JU15 (see the Output Voltage
Selection section).
Jumper Selection
Enable (EN)
The MAX1531 features an enable (EN) pin that enables
or disables the MAX1531 and the EV kit’s output. The
EN pin can also be used with resistor-dividers R3 and
R4 to set the lower limit of the input voltage range (refer
to the On/Off Control (EN) section in the MAX1531 data
sheet for further detail). The 3-pin jumper JU1 provides
an option to enable, disable, or use the undervoltage
threshold feature for the MAX1531 EV kit. Table 1 lists
the selectable jumper options.
The gamma reference (VGAM) is set to +9.7V using a lin-
ear regulator controller and an external pnp bipolar pass
transistor. This gamma reference can provide at least
50mA of current. The gamma linear regulator’s output
can be adjusted between +1.24V and its input voltage,
which is either the EV kit input voltage (PIN) or the output
of the MAX1522 step-up regulator, depending on jumper
JU14 (see the Output Voltage Selection section).
Table 1. Jumper JU1 Functions
SHUNT
LOCATION
MAX1531 (U1)
IC STATUS
EN PIN
The TFT gate-on supply (GON) uses a two-stage posi-
tive charge pump to generate approximately +33V. The
output is postregulated to +25V using a linear regulator
controller and an external pnp bipolar pass transistor
and can provide at least 25mA. The positive linear reg-
ulator’s output can be adjusted between +1.24V and its
input, which depends on the EV kit’s input voltage and
the charge-pump configuration, jumpers JU12 and
JU13 (see the Output Voltage Selection section).
Connected to GND
None
Disabled
Connected to PIN
through resistor-
dividers R3 and R4
1-2
(Default)
Enabled
when V
> 9V
PIN
2-3
Connected to VL
Enabled
Switching Frequency Selection (FREQ)
The MAX1531 EV kit features an option to choose the
step-down switching regulator’s operating frequency
(JU2). Table 2 lists the selectable jumper options. The
EV kit is configured for 500kHz operation. Optimum
performance at 250kHz requires a larger inductor value
(refer to the Inductor Selection section in the MAX1531
data sheet).
The TFT gate-off supply (GOFF) uses a negative charge
pump to generate approximately -11V. The output is
postregulated to -9V using a linear regulator controller
and an external npn bipolar pass transistor and can pro-
vide greater than 50mA. The negative linear regulator’s
output can be adjusted between 0V and its input volt-
4
_______________________________________________________________________________________
MAX1531 Evaluation Kit
Table 2. Jumper JU2 Functions
Table 3. Jumper JU3 Function
SHUNT
LOCATION
MAX1531 EV KIT
FREQUENCY
SHUNT
LOCATION
FREQ PIN
SEQ PIN
MAX1531 STATE
Installed
Connected to GND
Frequency = 250kHz
Sequence block disabled.
Connected to VSRC, VGAM, GON, and
None
(Default)
Connected to VL
through R5
Installed
Frequency = 500kHz
GND
GOFF disabled, regardless of
ONL2 to ONL5 voltage levels.
Power-Up Sequencing (SEQ)
Sequence block enabled.
Each ONL_ sources 2µA.
VGAM soft-starts when ONL2
reaches 1.24V.
The EV kit features adjustable power-up sequencing for
several of the linear regulators. After the MAX1531’s EN
pin goes high, the internal VL linear regulator starts up
and the step-down switching regulator soft-starts.
When the step-down regulator reaches regulation, the
logic-voltage-supply linear regulator (VLOG) and the
sequence block that controls the other four linear regu-
lators are simultaneously enabled. The logic regulator
soft-starts immediately but the sequence block starts
only if SEQ is high. SEQ is controlled by JU3.
None
(Default)
Connected to GON soft-starts when ONL3
VL through R6 reaches 1.24V.
VSRC soft-starts when ONL4
reaches 1.24V.
GOFF soft-starts when ONL5
reaches 1.24V
Each linear regulator soft-starts individually when it is
enabled. After SEQ goes high, the ONL2 to ONL5 pins
each source current into C11, which controls the overall
time for startup. Resistors R14, R15, and R16 determine
the startup spacing between the respective regulator
and JU8 to JU11 determine the startup order. Each
regulator starts after SEQ is high and its ONL_ pin
exceeds 1.24V. JU4 to JU7 enable immediate startup
of their respective regulator after the step-down regula-
tor reaches regulation and SEQ is high, without addi-
tional delay. (See the Power-Up Sequencing section.)
See Tables 3 through 7 for configuring the jumpers.
Table 4. ONL2 Setting (JU4 and JU8)
JU4 SHUNT
LOCATION
JU8 SHUNT
LOCATION
ONL2 PIN
SEQUENCING MODE
Gamma linear regulator enabled immediately if JU3 is removed
(SEQ = high) and step-down switching regulator soft-start is
finished. Sequence not used.
Connected to VL
through R39
1-2
1-4
Don’t Care
Connected to
GND
Don’t Care
1-2
Gamma linear regulator disabled.
Gamma linear regulator soft-starts about 6ms after sequence
block enabled.
Connected to R14
Connected to R15
Connected to R16
Connected to C11
1-3
(Default)
Gamma linear regulator soft-starts about 9ms after sequence
block enabled.
Gamma linear regulator soft-starts about 12ms after sequence
block enabled.
1-3
(Default)
1-4
1-5
Gamma linear regulator soft-starts about 15ms after sequence
block enabled.
_______________________________________________________________________________________
5
MAX1531 Evaluation Kit
Table 5. ONL3 Setting (JU5 and JU9)
JU5 SHUNT
LOCATION
JU9 SHUNT
LOCATION
ONL3 PIN
SEQUENCING MODE
GON linear regulator enabled immediately if JU3 is removed
(SEQ = high) and step-down switching regulator soft-start is
finished. Sequence not used.
Connected to VL
through R40
1-2
1-4
Don’t Care
Connected to
GND
Don’t Care
1-2
GON linear regulator disabled.
GON linear regulator soft-starts about 6ms after sequence block
enabled.
Connected to R14
Connected to R15
Connected to R16
Connected to C11
GON linear regulator soft-starts about 9ms after sequence block
enabled.
1-3
1-3
(Default)
GON linear regulator soft-starts about 12ms after sequence block
enabled.
1-4
1-5
(Default)
GON linear regulator soft-starts about 15ms after sequence block
enabled.
Table 6. ONL4 Setting (JU6 and JU10)
JU6 SHUNT
LOCATION
JU10 SHUNT
LOCATION
ONL4 PIN
SEQUENCING MODE
VSRC linear regulator enabled immediately if JU3 is removed
(SEQ = high) and step-down switching regulator soft-start is
finished. Sequence not used.
Connected to VL
through R41
1-2
1-4
Don’t Care
Don’t Care
Connected to
GND
VSRC linear regulator disabled.
1-2
(Default)
VSRC linear regulator soft-starts about 6ms after sequence block
enabled.
Connected to R14
Connected to R15
Connected to R16
Connected to C11
VSRC linear regulator soft-starts about 9ms after sequence block
enabled.
1-3
1-4
1-5
1-3
(Default)
VSRC linear regulator soft-starts about 12ms after sequence
block enabled.
VSRC linear regulator soft-starts about 15ms after sequence
block enabled.
6
_______________________________________________________________________________________
MAX1531 Evaluation Kit
Table 7. ONL5 Setting (JU7 and JU11)
JU7 SHUNT
LOCATION
JU11 SHUNT
LOCATION
ONL5 PIN
SEQUENCING MODE
GOFF linear regulator enabled immediately if JU3 is removed
(SEQ = high) and step-down switching regulator soft-start is
finished. Sequence not used.
Connected to VL
through R42
1-2
1-4
Don’t Care
Connected to
GND
Don’t Care
1-2
GOFF linear regulator disabled.
GOFF linear regulator soft-starts about 6ms after sequence block
enabled.
Connected to R14
Connected to R15
Connected to R16
Connected to C11
GOFF linear regulator soft-starts about 9ms after sequence block
enabled.
1-3
1-3
(Default)
1-4
(Default)
GOFF linear regulator soft-starts about 12ms after sequence
block enabled.
GOFF linear regulator soft-starts about 15ms after sequence
block enabled.
1-5
Positive Charge Pump
Table 8. Jumper JU12 Functions
The positive charge pump of the MAX1531 EV kit pow-
ers the GON linear regulator and features an option to
cascade up to two charge-pump stages. The charge
pump’s first stage can be connected to PIN or VOUT,
and the charge pump’s second stage can be connect-
ed to PIN or the previous stage. Jumpers JU12 and
JU13 configure the number of stages and select the
voltage source for the positive charge pump on the
MAX1531 EV kit. Tables 8 and 9 list the jumper options.
The default configuration of the positive charge pump
of the MAX1531 EV kit is a two-stage charge pump
powered from PIN as indicated in Tables 8 and 9.
1ST STAGE
SHUNT
LOCATION
POSITIVE
CHARGE
PUMP
OPERATING MODE
First stage of a two-stage
charge pump connected to
PIN.
1-2
(Default)
Connected to
PIN
First stage of a two-stage
charge pump connected to
VOUT.
Connected to
VOUT
2-3
Since the positive charge pump powers the GON linear
regulator, ensure that the combination of the charge-
pump configuration and the input voltage range (PIN)
does not over stress the GON linear regulator’s external
The first stage is not used for
one-stage charge pumps.
None
Not used
pass transistor. The V
maximum rating of the
CEO
Table 9. Jumper JU13 Functions
MMBT3904 used on this EV kit is 40V. If the input volt-
age (PIN) exceeds +13.2V, either reconfigure the
charge pump (using JU12 and JU13) as a two-stage
charge pump from VOUT or a one-stage charge pump
from PIN, as appropriate, or select a higher-voltage-
rated transistor for Q3. Also, if higher charge-pump
voltages are required, ensure that Q6 and C15 are not
over stressed. Refer to the Charge Pumps section of
the MAX1531 data sheet for more information on select-
ing a charge-pump configuration.
2ND STAGE
SHUNT
LOCATION
POSITIVE
CHARGE
PUMP
OPERATING MODE
Connected to One-stage charge pump
1-2
PIN
connected to PIN.
Connected to
2-3
previous stage Last stage of a two-stage
(Default)
charge pump.
charge-pump
output
None
Not used
Charge pump not used.
_______________________________________________________________________________________
7
MAX1531 Evaluation Kit
VGAM Power Supply
The power supply for the VGAM linear regulator can be
connected to PIN or STEP_UP. PIN is the input voltage
for the EV kit. STEP_UP is the output of the MAX1522
step-up switching regulator circuit on the EV kit.
Jumper JU14 selects the power supply for the VGAM
linear regulator on the MAX1531 EV kit. Table 10 lists
the jumper options.
Table 12. Jumper JU16 Functions
SHUNT
MAX1522
MAX1522
LOCATION
SHDN PIN
OPERATING MODE
Connected to
VOUT
1-2
Enabled
Disabled
2-3
(Default)
Connected to
GND
Table 10. Jumper JU14 Functions
using JU16 and set JU14 and JU15 so that VGAM and
VSRC use the step-up’s output.
VGAM
POWER
SUPPLY
SHUNT
LOCATION
OPERATING MODE
Output Voltage Selection
Step-Down Switching-Regulator Output
VGAM powered from the
output of the MAX1522 step-
up regulator.
Connected to
STEP_UP
1-2
Voltage (V )
OUT
The MAX1531 EV kit’s step-down switching-regulator
output (VOUT) is set to +3.3V by feedback resistors R1
and R2. To generate output voltages other than +3.3V
2-3
(Default)
Connected to
PIN
VGAM powered from PIN.
VGAM not used.
(from +1.24V up to 0.6 x V ), select different external
PIN
None
Not used
voltage-divider resistors (R1, R2). Output capacitor C7
is rated to +6.3V. To set the output voltage greater than
+6.3V, use a higher-voltage-rated capacitor. Refer to
the Main Step-Down Regulator Output Voltage
Selection section in the MAX1531 data sheet for
instructions on selecting the resistors.
VSRC Power Supply
The power supply for the VSRC linear regulator can be
connected to PIN or STEP_UP. PIN is the input voltage
for the EV kit. STEP_UP is the output of the MAX1522
step-up switching regulator circuit on the EV kit.
Jumper JU15 selects the power supply for the VSRC
linear regulator on the MAX1531 EV kit. Table 11 lists
the jumper options.
Logic-Voltage-Supply Linear Regulator
Output Voltage (VLOG)
The MAX1531 EV kit’s logic-voltage-supply linear regu-
lator output (VLOG) is set to +2.5V by feedback resis-
tors R9 and R10. To generate output voltages other
than +2.5V (from +1.24V up to VOUT) select different
external voltage-divider resistors (R9, R10). Output
capacitor C9 is rated to +6.3V. To set the output volt-
age greater than +6.3V, use a higher-voltage-rated
capacitor. Refer to the Linear-Regulator Controllers
Output Voltage Selection section in the MAX1531 data
sheet for instructions on selecting the resistors.
Table 11. Jumper JU15 Functions
VSRC
POWER
SUPPLY
SHUNT
LOCATION
OPERATING MODE
VSRC powered from the
output of the MAX1522 step-
up regulator.
Connected to
STEP_UP
1-2
Gamma-Reference Linear Regulator
Output Voltage (VGAM)
2-3
(Default)
Connected to
PIN
The MAX1531 EV kit’s gamma-reference linear regula-
tor output (VGAM) is set to +9.7V by feedback resistors
R18 and R19. To generate output voltages other than
+9.7V (from +1.24V up to its input voltage) select differ-
ent external voltage-divider resistors (R18, R19). Output
capacitor C12 is rated to +16V. To set the output volt-
age greater than +16V, use a higher-voltage-rated
capacitor. Refer to the Linear-Regulator Controllers
Output Voltage Selection section in the MAX1531 data
sheet for instructions on selecting the resistors.
VSRC powered from PIN.
VSRC not used.
None
Not used
The MAX1522 Step-Up Circuit
The MAX1531 EV kit includes a MAX1522 step-up
switching regulator. This regulator is not generally
needed, but is provided as a convenience for applica-
tions where the input voltage (PIN) can be less than
VSRC. If the step-up is needed, enable the MAX1522
8
_______________________________________________________________________________________
MAX1531 Evaluation Kit
Gate-On Linear Regulator Output
Voltage (GON)
Source-Supply Linear Regulator Output
Voltage (VSRC)
The MAX1531 EV kit’s gate-on linear regulator output
(GON) is set to +25V by feedback resistors R25 and
R26. To generate output voltages other than +25V (from
+1.24V up to the linear regulator’s input, which is the
output of the positive charge pump), select different
external voltage-divider resistors (R25, R26). Take care
The MAX1531 EV kit’s source-supply linear regulator
output (VSRC) is set to +10V by feedback resistors R22
and R23. To generate output voltages other than +10V
(from +1.24V up to its input voltage) select different
external voltage-divider resistors (R22, R23). Output
capacitor C13 is rated to +16V. To set the output volt-
age greater than +16V, use a higher-voltage-rated
capacitor. Refer to the Linear-Regulator Controllers
Output Voltage Selection section in the MAX1531 data
sheet for instructions on selecting the resistors.
not to exceed either the pnp pass transistor’s V
rat-
CEO
ing (40V) or the output capacitor’s (C16) +50V rating.
Before GON is enabled, Q3 is off and the positive
charge pump’s full output voltage is present across Q3.
If the input voltage (PIN) exceeds 13.2V, do not power
the EV kit with the charge pump configured as a two-
stage charge pump powered from PIN, as Q3’s 40V
rating will be exceeded. Configure JU12 and JU13 for a
two-stage charge pump powered from VOUT or as a
one-stage charge pump powered from PIN, whichever
is appropriate. Alternatively, select a different transistor
for Q3 and possibly Q6, which must withstand the
Gate-Off Linear Regulator Output
Voltage (GOFF)
The MAX1531 EV kit’s negative linear regulator output
(GOFF) is set to -9V by feedback resistors R28 and
R29. To generate output voltages other than -9V (0V
down to its input voltage), select different external volt-
age-divider resistors (R28, R29). Output capacitor C19
is rated to -16V. To set the output voltage below -16V,
use a higher-voltage-rated capacitor. Refer to the
Linear-Regulator Controllers Output Voltage Selection
and Charge Pumps sections in the MAX1531 data
sheet for instructions on selecting the resistors.
same voltage, minus V . If V
exceeds +20V, even
PIN
PIN
a one-stage charge pump will exceed +40V, so either
change Q3 or disable the charge pump entirely and
power the linear regulator directly from PIN, whichever
is appropriate.
Evaluating the MAX1530
The MAX1531 EV kit can also evaluate the MAX1530.
To evaluate the MAX1530, replace U1 with the
MAX1530. Refer to the MAX1530/MAX1531 data sheets
for additional information.
Refer to the Linear-Regulator Controllers Output
Voltage Selection section in the MAX1531 data sheet
for instruction on selecting the voltage-divider resistors.
Also, refer to the Charge Pumps section for more infor-
mation about configuring the positive charge pump.
_______________________________________________________________________________________
9
MAX1531 Evaluation Kit
AM5X31
Figure 1. MAX1531 EV Kit Schematic—Sheet 1 of 2
10 ______________________________________________________________________________________
MAX1531 Evaluation Kit
PIN
C25
4.7µF
VOUT
6
C26
1µF
L2
22µH
D2
1 2
5 6
N2
V
CC
3
SET
3
5
2
EXT
FB
U2
4
STEP_UP
MAX1522
R31
110kΩ
1%
JU16
2
1
4
SHDN
C24
10µF
3
GND
1
R32
10.0kΩ
1%
R33
0.050Ω
Figure 2. MAX1531 EV Kit Schematic—Sheet 2 of 2
______________________________________________________________________________________ 11
MAX1531 Evaluation Kit
Figure 3. MAX1531 EV Kit Component Placement Guide—
Component Side
Figure 4. MAX1531 EV Kit PC Board Layout—Component Side
Figure 5. MAX1531 EV Kit PC Board Layout—GND Layer 2
Figure 6. MAX1531 EV Kit PC Board Layout—VCC Layer 3
12 ______________________________________________________________________________________
MAX1531 Evaluation Kit
Figure 7. MAX1531 EV Kit PC Board Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13
© 2004 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
相关型号：
MAX1534ETE+T
Switching Regulator, 2A, 200kHz Switching Freq-Max, BICMOS, 4 X 4 MM, 0.80 MM HEIGHT, QFN-16
MAXIM
©2020 ICPDF网 联系我们和版权申明