MAX16031EVKIT [MAXIM]
LEDs Indicate Each Output is State;型号: | MAX16031EVKIT |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | LEDs Indicate Each Output is State |
文件: | 总18页 (文件大小:1019K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-1ꢁ40; Rev 0; 11/07
MAX16031 Evaluation Kit
Evluates:MAX6031
General Description
Features
♦ USB Interface to Host PC
The MAX16031 evaluation kit (EV kit) provides a proven
printed-circuit board (PCB) layout that facilitates evalu-
ation of the MAX16031 EEPROM-based system monitor
with nonvolatile fault memory. This EV kit is a fully
assembled and tested surface-mount board.
♦ Easy-to-Use GUI Software
♦ Facilitates Programming of MAX16031s on
Prototype Boards
The EV kit includes an on-board USB-to-JTAG and I2C
interface facilitating communications between the host
PC and the MAX16031. A DAC connected to the moni-
toring inputs and the status LEDs connected to each
programmable output make it easy to evaluate the vari-
ous monitoring functions of the MAX16031.
♦ LEDs Indicate Each Output’s State
♦ On-Board DAC Simulates Monitored Voltages
♦ Convenient Test Points and Headers for Easy
Evaluation
♦ Fully Assembled and Tested
This EV kit data sheet assumes basic familiarity with the
MAX16031. Refer to the MAX16031/MAX16032 IC data
sheet for more detailed information.
Ordering Information
PART
TYPE
MAX16031EVKIT+
EV Kit
+Denotes lead-free and RoHS-compliant.
Component List
DESIGNATION QTY
DESCRIPTION
DESIGNATION
QTY
DESCRIPTION
2.2µF 20ꢀ, 10V XꢁR ceramic
capacitors (080ꢁ)
TDK C2012XꢁR1A22ꢁM
Taiyo Yuden LMK212BJ22ꢁMG
1μF 10%, 10V X5R ceramic
capacitors (0805)
TDK C2012X5R1A105K
KEMET C0805C105K4PAC
C1, C2, C4,
C100, C108
C112, C113
C114
2
1
5
0.1μF 10%, 25V X7R ceramic
capacitors (0805)
TDK C2012X7R1E104K
Taiyo Yuden TMK212B104KT
33pF ꢁꢀ, ꢁ0V C0G ceramic
capacitor (0603)
TDK C1608C0G1H330J
Taiyo Yuden UMK107CG330JZ
C3, C5, C6
C7
3
0
3
Not installed, capacitor (0805)
EXT PWR
F100
1
1
2
3
1
1
Test point, red
ꢁ00mA fast-acting fuse (240ꢁ)
Test points, black
3-pin headers
0.1μF 10%, 25V X7R ceramic
capacitors (0603)
TDK C1608X7R1E104K
Taiyo Yuden TMK107BJ104KA
C101, C102,
C103
GND, REF
J1, J2, J4
J3
2-pin header
18pF 5%, 50V C0G ceramic
capacitors (0603)
TDK C1608C0G1H180J
Taiyo Yuden UMK107CG180JZ
J100
2 x 3-pin header
C104, C105,
C106, C107
4
1
1
LED1–LED7,
LED100–LED103
11
Green LEDs (1206)
P100
1
0
1
1
1
1
1
USB_B right-angle connector
Not installed
4.7μF 20%, 6.3V X5R ceramic
capacitor (0805)
TDK C2012X5R0J475M
Taiyo Yuden JMK212BJ475MG
P101, P102
C110
C111
P1
P2
P3
P4
Pꢁ
ꢁ-pin header
2 x ꢁ-pin header
11-pin header
0.01μF 10%, 50V X7R ceramic
capacitor (0603)
TDK C1608X7R1H103K
Taiyo Yuden UMK107B103KZ
9-pin header
4-pin header
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX16031 Evaluation Kit
Component List (continued)
DESIGNATION
QTY
DESCRIPTION
DESIGNATION
QTY
DESCRIPTION
npn bipolar transistors
Fairchild MMBT3904
Maxim dual, low-noise, low-
dropout linear regulator
Q1, Q2
2
U100
1
Diodes Inc. MMBT3904-7-F
MAX8882EUTAQ+ (6-pin SOT23)
R1–R7,
R100–R103
Maxim USB peripheral controller
MAX3420EECJ+ (32-pin LQFP)
11 221ꢀ 1% resistors (0805)
U101
U102
1
1
R8–R14, R104
R23, R112
8
0
2
3
3
10kꢀ 1% resistors (0805)
Not installed, resistors
Maxim microcontroller
MAXQ2000-RAX+ (68-pin QFN-EP*)
R105, R106
33.2ꢀ 1% resistors (0805)
4.75kꢀ 1% resistors (0805)
8-row DIP switches
12MHz crystal (HCM49)
Citizen HCM49-12.000MABJ-UT
Y100
Y101
Y102
—
1
0
1
5
1
1
R108, R109, R110
S1, S2, S3
Not installed, 32kHz crystal
Maxim EEPROM-based system
monitor
MAX16031ETM+ (48-pin TQFN)
20MHz crystal (HCM49)
Citizen HCM49-20.000MABJ-UT
U1
U2
U3
1
1
1
Shunts
Maxim octal 12-bit voltage-output
DAC with serial interface
MAX5306EUE+ (16-pin TSSOP)
USB high-speed A-to-B cable,
5ft (1.5m)
—
Evluates:MAX6031
—
PCB: MAX16031 Evaluation Kit+
Maxim precision, low-dropout,
micropower voltage reference
MAX6025AEUR+ (3-pin SOT23)
*EP = Exposed paddle.
Component Suppliers
SUPPLIER
PHONE
WEBSITE
Diodes, Inc.
805-446-4800
888-522-5372
864-963-6300
800-348-2496
847-390-4373
www.diodes.com
Fairchild Semiconductor
KEMET Corp.
www.fairchildsemi.com
www.kemet.com
Taiyo Yuden
www.t-yuden.com
TDK Corp.
www.component.tdk.com
Note: Indicate that you are using the MAX16031 when contacting these component suppliers.
2) Connect the MAX16031 EV kit to a PC using the
Quick Start
Required Equipment
Before beginning, the following equipment is needed:
USB cable provided with the EV kit. LED100 will
light indicating that the EV kit has power.
3) Install the EV kit software.
4) Launch MAX16031.exe.
•
•
MAX16031 EV kit (includes USB cable)
A user-supplied PC with a spare USB port
ꢁ) Click the I2C radio button in the Connect dialog
box, and make sure Address is 0x18. Press the OK
button.
Note: In the following sections, software-related items
are identified by bolding. Text in bold refers to items
directly from the EV kit software.
6) Click the number 0.00 next to DAC Voltage for IN1.
Procedure
The MAX16031 EV kit is fully assembled and tested.
Follow the steps below to verify board operation:
7) In the Set Input Voltage dialog box, enter 1.00 and
press the OK button.
8) Note that the voltage in the chart-recorder view
increases to 1V.
1) Make sure jumpers J1 and J2 are in the 0 position, J3
is closed, J100 is in the 3.3V position, and J4 is in the
1-2 position. Also ensure that all switches in switch
banks S1, S2, and S3 are all in the ON position.
2
_______________________________________________________________________________________
MAX16031 Evaluation Kit
Evluates:MAX6031
Detailed Description of Software
Connecting to the MAX16031 EV Kit
Make sure the EV kit is connected to the PC by the USB
cable. Launch the software and in the Connect dialog
(Figure 1), select the I2C or JTAG radio button and
click OK. If the software is being used without the EV kit
connected, select the Demo (No Hardware Required)
radio button.
2
The I C slave address may be specified. The default is
0x18, but other values (depending on the settings of
jumpers J1 and J2) can be used.
Voltages Tab
The Voltages tab (Figure 2) provides a visual indication
of the voltage present on every IN_ input. Each channel
has a settings dialog (accessed by clicking the under-
lined IN_ link), a DAC output voltage setting, settings
for each overvoltage and undervoltage threshold, two
fault flags, and a chart-recorder view.
Figure 1. Connect Dialog
Figure 2. Voltages Tab
_______________________________________________________________________________________
3
MAX16031 Evaluation Kit
Each IN_ input can be connected to the on-board
MAXꢁ306 DAC using switch bank S1. This allows the
voltage at the IN_ input to be manually controlled through
the EV kit software. Click the link next to DAC Voltage to
set the voltage of the DAC in the 0 to 2.ꢁV range. The
DAC voltage can also be changed by dragging the dot-
ted green line, shown in the chart-recorder view.
To set the primary or secondary overvoltage or under-
voltage thresholds for a particular channel, click the
appropriate underlined number next to that parameter.
The primary thresholds can also be modified by drag-
ging the dotted red lines in the chart-recorder view. The
secondary thresholds can be changed the same way;
both appear as dotted yellow lines.
Two fault flag indicators are associated with each chan-
nel. The upper one corresponds to the primary fault
thresholds; the lower one corresponds with the sec-
ondary fault thresholds. If an undervoltage or overvolt-
age fault occurs, one or both these indicators will turn
red and remain so even after the original fault condition
is removed. To clear a fault indicator, click the indicator
and select Clear Fault or Clear All Faults on the menu
that appears.
Evluates:MAX6031
Each chart-recorder view shows the voltage on the cor-
responding IN_ input with a solid green line. To zoom in
and zoom out, click the magnifying glass icons in the
upper right of the chart-recorder view. Another way to
zoom in and out is to click and “drag” a selection rec-
tangle. Drag from upper left to lower right to zoom in,
and from lower right to upper left to zoom out.
Figure 3. Settings Dialog
The Settings dialog (Figure 3) can set the IN input-volt-
age range to one of three settings: 1.4V, 2.8V, and
ꢁ.6V. To enable channel monitoring, make sure the
Enable Fault Detection checkbox is selected. The
Disable Interrupts and Outputs for group box allows
faults on the primary or secondary thresholds to be
“masked,” which prevents them from triggering an
SMBus™ interrupt or asserting a fault output. The Save
State to EEPROM on group box selects which type of
fault can trigger a nonvolatile fault save operation.
Two IN inputs can be paired to form a combined differ-
ential input. Click any of the Single Ended links in the
center of the window to pair two inputs together, or to
separate two paired inputs.
SMBus is a trademark of Intel Corp.
4
_______________________________________________________________________________________
MAX16031 Evaluation Kit
Evluates:MAX6031
the settings dialog. To enable channel monitoring,
make sure Enable Fault Detection is selected (Figure
ꢁ). The Disable Interrupts and Outputs for group box
allows faults on the primary or secondary thresholds to
be “masked,” which prevents them from triggering an
SMBus interrupt or asserting a fault output. The Save
State to EEPROM on group box controls whether a
fault can trigger a nonvolatile fault save operation.
Current and Temperature Tab
The Current and Temperature tab (Figure 4) provides
a set of chart-recorder views similar to the Voltages
tab. To select the display units for the temperature sen-
sors, click the appropriate setting of the Temperature
Display radio buttons.
Similar to the input channels on the Voltages tab, the
current and the temperature channels each have a set-
tings dialog. Click the title of each channel to display
Figure 4. Current and Temperature Tab
_______________________________________________________________________________________
5
MAX16031 Evaluation Kit
Each external temperature channel has some additional
items on the settings dialog, shown in Figure ꢁ.
Additional fault mask bits are provided for the diode-
short and diode-open faults, and two controls are pro-
vided to set the temperature offset and gain calibration
parameters. The value provided for gain controls the
current (in µA) of the internal high-current source, while
the offset controls the digital offset value added to the
temperature conversion result (in Celsius).
Output Control Tab
The Output Control tab (Figure 6) facilitates configura-
tion of the programmable outputs.
The MAX16031 has several programmable outputs:
FAULT1, FAULT2, OVERT, RESET, GPIO1, and GPIO2.
The FAULT1 and FAULT2 outputs can be configured to
depend on many combinations of fault conditions for all
voltage, current, and temperature channels that are not
masked. The OVERT output depends on combinations
of temperature-related faults. Finally, the RESET output
depends on a combination of fault conditions for both
voltage and temperature and for a programmable set of
voltage inputs. The RESET output also has a program-
mable timeout, which is the amount of time RESET
remains asserted after all fault conditions are cleared.
Evluates:MAX6031
GPIO1 and GPIO2 can be used as general-purpose
inputs or outputs (GPIOs), and can also be configured
to act as manual reset inputs or additional fault outputs.
When a GPIO is configured as a fault output, the follow-
ing fault conditions can be monitored:
•
Primary undervoltage and overvoltage for one
selectable voltage channel
•
One or more of the following: primary overvoltage
for all voltage inputs, secondary over/undervoltage
for all inputs, overtemperature for each sensor, or
secondary overcurrent
Figure ꢁ. Temperature Settings Dialog
•
Both of the above options at once
6
_______________________________________________________________________________________
MAX16031 Evaluation Kit
Evluates:MAX6031
Figure 6. Output Control Tab
Overcurrent settings include OC timeout, which con-
trols the amount of time a secondary overcurrent condi-
tion must be present before it triggers a fault, and OC
output pin, which controls whether the OVERC output
latches an overcurrent fault or follows the state of the
primary overcurrent comparator.
Miscellaneous Tab
Many other configuration options are available in the
Miscellaneous tab (Figure 7): the boot-up delay, the
temperature filter, overcurrent settings, deglitch set-
tings, fault settings, memory lock bits, and the SMBus
alert configuration.
Filtering of the voltage-monitoring channels is con-
trolled by the Hysteresis of all thresholds setting,
which sets the voltage difference between the rising
and falling voltage threshold of each fault comparator.
Require 2 faults in a row, when turned on, prevents
any voltage fault from occurring unless the fault condi-
tion is present for two complete ADC conversion cycles
in a row.
The After-boot timeout setting controls the time delay
from when power is applied, to when monitoring is
enabled. This can prevent a partially powered system
from triggering false fault signals during startup.
The Temp sense filter time constant provides the
ability to filter the temperature sensors to reduce noise.
_______________________________________________________________________________________
7
MAX16031 Evaluation Kit
The On major fault setting controls what information is
saved to the fault EEPROM during a fault condition.
Save only fault flags means that only the fault flags
are stored to EEPROM during a fault event; Save fault
flags and ADC means that both the fault flags and the
ADC readings for all channels are stored to EEPROM
during a fault event.
The registers and the configuration EEPROM can be
locked with the Configuration setting to prevent unin-
tentional modification of configuration settings. The lock
icon in the lower-left corner of the window also indi-
cates and controls this lock bit.
The fault EEPROM is locked automatically when a fault
condition occurs and must be unlocked before any
subsequent fault will get stored to EEPROM. Unlock it
using the ADC-related EEPROM lock setting.
Version code provides user access to register ꢁEh.
This register does not control any function of the chip,
but can be used to store user-defined data such as a
version number.
To enable full SMBus functionality and allow the
SMBALERT output to assert, the SMBALERT# Signal
option must be enabled.
Evluates:MAX6031
Figure 7. Miscellaneous Tab
8
_______________________________________________________________________________________
MAX16031 Evaluation Kit
Evluates:MAX6031
Most configuration registers have a matching EEPROM
location that is copied to the register when the
MAX16031 powers up. The Registers tab places each
pair on the same row. After experimenting with a partic-
ular register configuration, that configuration can be
written to the EEPROM by clicking the Commit
Configuration to EEPROM button.
Registers Tab
Besides the easy-to-use GUI controls, the MAX16031
can also be configured by directly modifying the regis-
ters and EEPROM. The Registers tab (Figure 8) pro-
vides access to the registers and EEPROM. Modify a
register by clicking the cell under the Value column,
entering the new value, and pressing Enter or clicking
in another cell.
Figure 8. Registers Tab
_______________________________________________________________________________________
9
MAX16031 Evaluation Kit
About
This menu item launches the About dialog, which dis-
plays the software version, whether the EV kit is connect-
ed, and the firmware revision of the USB interface.
Menu Reference
System
Connect... directs the software to open a connection
with a connected EV kit and brings up the Connect
dialog (Figure 1) to select the connection type. Once
connected, this menu item changes to Disconnect.
SMBus Alert Functionality
When the SMBALERT# signal is enabled using the
option in the Miscellaneous tab, any fault that occurs
will cause this signal to be asserted. When that hap-
pens, the status bar displays SMBALERT# detected.
Click here to send Alert Response Address. Clicking
the status bar item then causes the EV kit hardware to
issue an Alert Response Address command, which
returns the slave address of the SMBus device that trig-
gered the SMBus alert.
Save as SVF… writes the EEPROM configuration to an
SVF file, which is a standard format used by JTAG
device programmers for production programming.
Save Configuration… and Load Configuration…
save and load the register and EEPROM configuration
to a text file.
Polling
On and Off turn register polling on and off. When
polling is on, the controls in all the tabs are periodically
refreshed from the physical registers. If polling is off,
register content can be read from the device by select-
ing Read All Registers.
Detailed Description of Hardware
The MAX16031 monitors eight voltages, three tempera-
tures, and one current. Seven configurable outputs
indicate fault-status information. Figure 9 provides an
overview of the major features of the EV kit PCB.
Evluates:MAX6031
CONNECTED
ACTIVITY
EXT
PWR
GND
LED100
USB
EXTERNAL POWER
SUPPLY
POWER
LED103
LED102
LED101
(OPTIONAL)
J100
CURRENT-SENSE
RESISTOR
VCC SELECT
EEPROM
(OPTIONAL)
P2
JTAG
S1
S3
J3
2
I C
P1
PULLUP
VOLTAGE
SELECT
CURRENT-SENSE
BIAS
S2
J4
CONNECTS DAC
OUTPUTS TO
MONITORING
INPUTS
MONITORED INPUTS
CONFIGURES
JTAG AND I C
BUS ROUTING
2
MAX16031
OUTPUTS
Q2
Q1
OUTPUT
STATUS
INDICATORS
TEMPERATURE
SENSORS
1-800-737-7600 WWW.MAXIM-IC.COM
MAX16031 EVALUATION KIT+
P5
TEMPERATURE-SENSOR CONNECTIONS
2
I C ADDRESS SELECT
Figure 9. Evaluation Kit PCB Diagram
10 ______________________________________________________________________________________
MAX16031 Evaluation Kit
Evluates:MAX6031
USB-Host Interface
Voltage Monitoring
The eight voltage monitoring inputs connect to pins on
P3 located on the left side of the board. Switch bank S1
allows each input to be connected to the output of a
DAC, which allows the voltage to be set using the EV kit
software for ease of evaluation. The DAC output voltage
range is limited to 2.ꢁV. Do not attempt to force an
external voltage while the DAC is connected; doing so
could damage the DAC or the external voltage source.
The MAX16031 EV kit includes a built-in USB-to-
2
JTAG/I C host interface. The host interface uses
Maxim’s MAX3420 USB peripheral controller, along
with a MAXQ2000 microcontroller to communicate with
2
the host PC and generate the I C/JTAG bus signals.
Three indicators (LED101, LED102, LED103) provide
status information of the host interface. LED101 lights
during EEPROM write operations, LED102 lights during
2
I C or JTAG bus activity, and LED103 lights when the
software is communicating to the EV kit.
Current Monitoring
The current-sense inputs are connected to pins on
header P3 and can be used in two ways. A small volt-
age source can be applied directly across CS+ and
CS-, which the MAX16031 will measure directly. For this
situation, J3 must be closed, which connects CS+ to
To facilitate prototype development and programming,
the host interface can be used to interface with a
MAX16031 on another board by turning off switches
1-7 in switch bank S2. This disconnects the on-board
2
MAX16031 from the JTAG and I C buses. Connect to
V
CC
to ensure proper bias. As an alternative, a current-
the other board using P1 and P2. The pinout of each
sense resistor can be soldered in the R23 position and
CS+ and CS- can be connected in series with the
external circuit to be measured.
2
connector is shown in Tables 2 and 3. Note that the I C
pullup resistors are located on the EV kit.
The on-board MAX16031 can be connected to an
external JTAG or I C interface by turning switch bank
S3 (switches 1-7) off while keeping switch bank S2
(switches 1-7) on. Connect the external interface to P2
for JTAG or P1 for I C. The MAX16031 can be com-
pletely disconnected from the on-board USB host inter-
face by using this technique, while providing external
power to EXT PWR (J100 must be in the EXT position),
and disconnecting the on-board DACs by turning off all
the switches in switch bank S1.
If an external bias voltage is to be used, remove J3 and
connect the CS+ pin of P3 to the external source. Do
not supply a bias voltage higher than 28V. The current-
sense circuit in the MAX16031 will not function for bias
voltages less than 3V.
2
2
Temperature Monitoring
One of the temperature sensors is internal and the
other two are external. Both external temperature sen-
sors are included on the EV kit as Q1 and Q2, which
are diode-connected 2N3904 transistors. These can be
desoldered and replaced if necessary. The connec-
tions are easily accessible through header Pꢁ.
Each interface can be disconnected or connected sep-
2
arately. I C uses switches 1-3 on both S2 and S3 while
JTAG uses switches 4-7 on both S2 and S3.
Inputs and Outputs
Each output has a separate indicator LED and pullup
resistor, and each signal is brought out to a pin on P4.
An LED will light to indicate that the associated output
has gone to the logic-low state. The LEDs can be dis-
abled by turning off switch 8 in switch bank S2. The
pullup resistors are controlled by J4. To use an external
pullup voltage, connect J4 in the 2-3 position and con-
nect the voltage source to the VPU pin of P4.
Power Source
The MAX16031 IC can be powered from one of three
possible power supplies, controlled by jumper J100. To
power directly from the USB ꢁV supply, place the
jumper in the ꢁV position. To power from the on-board
3.3V regulator, place the jumper in the 3.3V position.
When the jumper is in the EXT position, the MAX16031
can be powered from an external power supply con-
nected to the EXT PWR test point. Do not supply a volt-
age higher than 14V.
GPIO1 and GPIO2 can also function as inputs. If they
are configured as such, connect the external input to
the GPIO1 or GPIO2 pin of P4.
Serial Interfaces
2
The MAX16031 has both a JTAG interface and an I C
A test point (REF) is provided to confirm the reference
voltage of the MAX16031, which is 1.4V (nominal). Do
not connect loads to this test point.
serial interface. The slave address of the on-board
MAX16031 can be set using J1 and J2, according to
Table 4.
______________________________________________________________________________________ 11
MAX16031 Evaluation Kit
Jumper Function Tables
Table 1. Jumper Function Table (J100, J3, J4, S1, S2, S3)
JUMPER
POSITION
FUNCTION
5V*
MAX16031 powered from 5V USB power
J100
3.3V
MAX16031 powered from 3.3V regulator
EXT
MAX16031 powered from EXT PWR test point
Current-sense amplifier biased externally (CS+ test point)
Open
J3
J4
Closed*
Current-sense amplifier biased from MAX16031 V
Output pullup resistors connected to 3.3V
CC
1-2*
2-3
1
Output pullup resistors connected to VPU test point
Connects IN1 to DAC channel 1 when closed
Connects IN2 to DAC channel 2 when closed
Connects IN3 to DAC channel 3 when closed
Connects IN4 to DAC channel 4 when closed
Connects IN5 to DAC channel 5 when closed
Connects IN6 to DAC channel 6 when closed
Connects IN7 to DAC channel 7 when closed
Connects IN8 to DAC channel 8 when closed
2
3
4
S1
5
6
7
Evluates:MAX6031
8
1
2
Connects P1 (I C) to on-board MAX16031 when closed
2
3
4
S2
5
Connects P2 (JTAG) to on-board MAX16031 when closed
Enables output LEDs when closed
6
7
8
1
2
Connects I C bus of host interface to P1 when closed
2
3
4
S3
5
Connects JTAG bus of host interface to P2 when closed
Not used
6
7
8
*Default position.
12 ______________________________________________________________________________________
MAX16031 Evaluation Kit
Evluates:MAX6031
2
Table 4. Jumper Function Table (J1, J2)
Table 2. I C Connector Pinout (P1)
PIN
FUNCTION
J1 SHUNT
POSITION
(A1)
J2 SHUNT
POSITION
(A0)
2
I C SLAVE
1
3.3V (output only)
ADDRESS
2
SDA
0*
0*
Z
1
0011_000 (18h)
0011_001 (19h)
0011_010 (1Ah)
0101_001 (29h)
0101_010 (2Ah)
0101_011 (2Bh)
1001_100 (4Ch)
1001_111 (4Fh)
1001_110 (4Eh)
3
Ground
SCL
0
4
0
5
SMBALERT#
Z
0
Z
Z
1
Z
Table 3. JTAG Connector Pinout (P2)
1
0
PIN
FUNCTION
1
Z
1
1
TCK
1
2
Ground
TDO
*Default position.
3
4
3.3V (output only)
5
TMS
—
6
7
— (Key)
—
8
9
TDI
10
Ground
______________________________________________________________________________________ 13
MAX16031 Evaluation Kit
Evluates:MAX6031
Figure 10. MAX16031 EV Kit Schematic
14 ______________________________________________________________________________________
MAX16031 Evaluation Kit
Evluates:MAX6031
+3.3
C100
1μF
C101
0.1μF
VBUS
R104
10kΩ
F100
R112
OPEN
500mA
R105
33.2Ω
1%
C104
18pF
P100
28
24
3
4
23 22
U100
1
2
VBUS
D-
VBUS
+2.5
+3.3
20
R100
D-
15
MAX8882
221Ω
GPX
6
1
3
Y100
12MHz
R106
33.2Ω
1%
OUTA
OUTB
BP
5
4
IN
SHDN
26
27
LED100
XI
XO
C113
2.2μF
3
4
21
29
30
31
32
1
2
7
8
C112
2.2μF
D+
GND
D+
C110
4.7μF
C111
0.01μF
GPIN0
GPIN1
GPIN2
GPIN3
C105
18pF
U101
MAX3420E
GND
2
17
14
13
12
11
10
USBINT
MOSI
MISO
SS
SCLK
RES
INT
MOSI
MISO
SS
SCLK
RES
USB_B
GPOUT0
GPOUT1
GPOUT2
GPOUT3
+3.3 VBUS
VCC
J100
C114
33pF
1
3
5
2
4
6
+2.5
+3.3
EXT PWR
GND
C108
1μF
9
18 19 5 6 16 25
VCC SEL
C102
C103
0.1μF
0.1μF
RST Q
57 56 55 54
49
27
33
+3.3
58
53 RX0
52 TX0
48
47
46
45
TMS
TCK
TDI
SEG0/P0.0
SEG1/P0.1
SEG2/P0.2
SEG3/P0.3
SEG4/P0.4/INT0
SEG5/P0.5/INT1
SEG6/P0.6/INT2
SEG7/P0.7/INT3
SEG8/P1.0
P7.1/RX0/INT15
P7.0/TX0/INT14
P6.5/T0/WKOUT1
P6.4/T0B/WKOUT0
P6.3/T2/OW_IN
P6.2/T2B/OW_OUT
P6.1/T1/INT13
DIN
DCLK
59
60
61
62
63
64
65
66
67
68
1
2
3
4
5
6
7
8
9
R108
R109
R110
4.75kΩ
4.75kΩ
4.75kΩ
1%
1%
1%
TDO
ALERT
SCL
SDA
44 RES
43 USBINT
P6.0/T1B/INT12
41 MISO
40 SCLK
39 MOSI
38 SS
37
36
32 TDO Q
31 TMS Q
30 TDI Q
29 TCK Q
21 EX6
20 EX5
19 EX4
18 EX3
17 EX2
16 EX1
P5.7/MISO
P5.6/SCLK
P5.5/MOSI
SEG9/P1.1
SEG10/P1.2
SEG11/P1.3
SEG12/P1.4
SEG13/P1.5
SEG14/P1.6
SEG15/P1.7
SEG16/P2.0
SEG17/P2.1
SEG18/P2.2
SEG19/P2.3
SEG20/P2.4
SEG21/P2.5
SEG22/P2.6
SEG23/P2.7
SEG24/P3.0
SEG25/P3.1
U102
P5.4/SS
LED101 LED102 LED103
P5.3/TX1/INT11
P5.2/RX1/INT10
P4.3/TDO
CS
LDAC
MAXQ2000-RAX
LED
LED
LED
P101
P4.2/TMS
1
2
3
4
5
6
7
8
9
P4.1/TDI/INT9
P4.0/TCK/INT8
SEG31/P3.7/INT7
SEG30/P3.6/INT6
SEG29/P3.5/INT5
SEG28/P3.4/INT4
SEG27/P3.3
R101
221Ω
1%
R102
221Ω
1%
R103
221Ω
1%
+3.3
10
11
12
13
14
15
SEG26/P3.2
10
11
12
13
14
15
16
+3.3
EX1
EX2
EX3
EX4
EX5
EX6
P102
TCK Q
TDO Q
TMS Q
1
3
5
7
9
2
4
6
8
10
C106
22 23 24 25 26
28 42
34
35
51
50
18pF
RST Q
TDI Q
Y101
32kHz
Y102
20MHz
C107
18pF
TEST
JTAG_MAXQ
Figure 11. MAX16031 EV Kit Schematic—USB Interface
______________________________________________________________________________________ 15
MAX16031 Evaluation Kit
Evluates:MAX6031
Figure 12. MAX16031 EV Kit Component Placement Guide—Component Side
16 ______________________________________________________________________________________
MAX16031 Evaluation Kit
Evluates:MAX6031
Figure 13. MAX16031 EV Kit PCB Layout—Component Side
______________________________________________________________________________________ 17
MAX16031 Evaluation Kit
Evluates:MAX6031
Figure 14. MAX16031 EV Kit PCB Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
18 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2007 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
相关型号:
©2020 ICPDF网 联系我们和版权申明