MAX16152BDCT [MAXIM]
nanoPower Supervisor and Watchdog Timer;
| 型号： | MAX16152BDCT |
| 厂家： | 
MAXIM INTEGRATED PRODUCTS |
| 描述： | nanoPower Supervisor and Watchdog Timer |
| 文件： | 总20页 (文件大小：405K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
EVALUATION KIT AVAILABLE
Click here for production status of specific part numbers.
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
General Description
Benefits and Features
The MAX16152/MAX16153/MAX16154/MAX16155 ultra-
low-current supervisory circuits monitor a single system
supply voltage and the integrity of code execution by a
microprocessor or microcontroller. These supervisors as-
● 400nA (typ) Supply Current
● 1.2V to 5.5V Operating Supply Range
● Monitors Supply Voltage and Provides System Reset
Signal
sert the reset output whenever the V
supply voltage is
● 1.5V to 5V Input Threshold Range in 100mV
Increments
● Watchdog Function Detects Faulty Code Execution
● Open-Drain Reset and Watchdog Outputs
● Watchdog Timer Enable Input
● 6-Bump WLP Package
CC
greater than the minimum operating voltage, but less than
the reset threshold. After the supply voltage rises above
the reset threshold, the reset output remains asserted for
the reset timeout period, and then de-asserts. Reset volt-
age thresholds are available from 1.50V to 5.0V in approx-
imately 100mV increments.
● 6-Pin SOT23 Package
● -40°C to +125°C Operating Temperature Range
A watchdog timer circuit monitors microprocessor or mi-
crocontroller activity. During normal operation, the micro-
processor or microcontroller should repeatedly toggle the
watchdog input (WDI) before the supervisor’s watchdog
timeout period elapses to confirm that the system is exe-
cuting code properly. If the microprocessor or microcon-
troller does not provide a valid watchdog input transition
before the timeout period expires, the supervisor asserts
a watchdog (WDO) output to signal that the system is
not executing code as expected. The watchdog output
pulse can be used to reset the microprocessor or micro-
controller, or it may be used to interrupt the system to
warn of execution errors. The MAX16152 and MAX16153
feature a manual reset input (MR) to allow an external
pushbutton or logic signal to initiate a reset pulse. The
MAX16154 and MAX16155 feature a logic input (WD_EN)
that allows the system to enable and disable the watchdog
function.
Ordering Information appears at end of data sheet.
The MAX16152 and MAX16154 are offered in a 0.86mm
x 1.27mm 6-bump WLP, while the MAX16153 and
MAX16155 are offered in 6-pin SOT23 package. All de-
vices operate over the -40ºC to +125ºC temperature
range.
Applications
● Portable/Battery-Powered Equipment
● Tablets/e-Readers/Mobile Devices
● Glucose Monitors/Patient Monitor
● Metering
19-100532; Rev 0; 4/2019
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Typical Application Circuit
1.2V ≤ VIN ≤ 5.5V
V
CC
RST
V
RST
CC
0.1µF
MAX16155
I/O
WDI
µP
WD_EN
WDO
NMI
GND
GND
www.maximintegrated.com
Maxim Integrated | 2
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Absolute Maximum Ratings
V
CC
to GND.............................................................. -0.3V to +6V
Continuous Power Dissipation (SOT23) (T = +70°C, derate
A
WDI, WD_EN to GND................................... -0.3V to V
WDO, RST to GND................................................... -0.3V to +6V
Maximum Current, Any Pin (input/output) ........................... 20mA
+ 0.3V
8.70mW/°C above +70°C) ................................................696mW
Operating Temperature Range...........................-40°C to +125°C
Junction Temperature.......................................................+150°C
CC
Continuous Power Dissipation (WLP) (T = +70°C, derate 10.5
A
mW/°C above +70°C)....................................................... 840mW
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may
affect device reliability.
Package Information
6 WLP
Package Code
U6+1
Outline Number
21-0058
90-0175
Land Pattern Number
Thermal Resistance, Four-Layer Board:
Junction-to-Ambient (θ
)
115
80
JA
Junction-to-Case Thermal Resistance (θ
)
JC
6 SOT23
Package Code
W60C1+2
21-100258
—
Outline Number
Land Pattern Number
Thermal Resistance, Four-Layer Board:
Junction-to-Case Thermal Resistance (θJC
)
95
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages.
Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different
suffix character, but the drawing pertains to the package regardless of RoHS status.
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a
four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/
thermal-tutorial.
www.maximintegrated.com
Maxim Integrated | 3
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Electrical Characteristics
((V
= 1.2V to 5.5V, T = -40ºC to +125ºC. Limits over the operating temperature range and relevant supply voltage range are
CC
A
guaranteed by production test and/or characterization. Typical values are at T = +25ºC and V
= V + 150mV.))
TH
A
CC
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Supply Voltage Range
1.2
5.5
900
5
V
Outputs not asserted, V
150mV
= V
+
TH
CC
Supply Current
400
nA
V
V
V
Threshold Range
Reset Threshold
1.5
CC
CC
V
V
falling
rising
-2.5
+2.5
%
TH_AC
CC
Accuracy
V
CC
Reset Threshold
V
V
0.4
80
%
μs
%
CC
Hysteresis
falling from (V + 100mV) to (V
-
TH
CC
TH
V
CC
to Reset Delay
t
RD
100mV)
Reset Timeout Period
Accuracy
t
Note 1
-50
+50
RP_AC
WATCHDOG
Watchdog Timeout
Period Accuracy
t
-50
-50
+50
+50
%
%
WD_AC
Watchdog Startup Delay
Accuracy
t
START-UP_AC
Time between low-to-high transition of
WD_EN and watchdog timer enabled.
Watchdog Setup Time
t
300
μs
SETUP
V
CC
V
CC
V
CC
≥ 1.0V, I
> 2.7V, I
> 4.5V, I
= 50μA
0.3
0.3
0.4
SINK
SINK
SINK
Output Voltage Low
V
OL
= 1.2mA
= 3.2mA
V
Watchdog Input Pulse
Width
t
After WDO deasserted
1
μs
ms
V
WDI
Watchdog Output Pulse
Width
t
100
300
WDO
0.8 x
Input Voltage High
V
IH
V
CC
0.3 x
V
CC
≥ 3.3V
V
CC
Input Logic-Low
V
IL
WDI, MR, WD_EN
V
0.3 x
1.5V ≥ V
CC
V
CC
Watchdog Output
Leakage Current
V
V
= 0 to 5.5V, output deasserted
1
μA
μA
ns
ns
WDO
Reset Ouput Leakage
Current
= 0 to 5.5V, reset output
RST
1
deasserted
WD_EN Input Glitch
Rejection
300
200
Manual Reset Input
Glitch Rejection
www.maximintegrated.com
Maxim Integrated | 4
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Electrical Characteristics (continued)
((V
= 1.2V to 5.5V, T = -40ºC to +125ºC. Limits over the operating temperature range and relevant supply voltage range are
CC
A
guaranteed by production test and/or characterization. Typical values are at T = +25ºC and V
= V + 150mV.))
TH
A
CC
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Manual Reset Input to
Reset Output Delay
t
250
ns
MRD
MR, WDI, WD_EN. Input connected GND
Input Leakage Current
-1
+1
µA
or V
CC
Note 1: In addition to the specified tolerance, t
has an uncertainty of ±4ms due to the power-up delay of internal blocks.
RP
www.maximintegrated.com
Maxim Integrated | 5
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Typical Operating Characteristics
(V
= 1.2V TO 5.5V, T = -40ºC TO 125ºC)
CC
A
www.maximintegrated.com
Maxim Integrated | 6
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Pin Configurations
6 WLP
TOP VIEW
MAX16152
1
2
3
A
V
CC
GND
WDI
RST
WDO
MR
B
6 SOT23
TOP VIEW
6
5
1
2
RST
V
CC
MAX16153
GND
WDI
MR
4
3
WDO
www.maximintegrated.com
Maxim Integrated | 7
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
6 WLP
TOP VIEW
MAX16154
1
2
3
A
V
CC
GND
WDI
RST
WDO
WD_EN
B
6 SOT23
TOP VIEW
1
2
V
6
5
CC
RST
MAX16155
GND
WDI
WD_EN
WDO
3
4
www.maximintegrated.com
Maxim Integrated | 8
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Pin Description
PIN
NAME
FUNCTION
MAX1615 MAX1615 MAX1615 MAX1615
2
3
1
2
4
5
1
2
Supply Voltage. V
monitoring input. Bypass with a 0.1μF capacitor to GND.
is the power supply input and the
CC
A3
A2
A3
A2
V
CC
GND
Ground
Watchdog Input. If WDI remains either high or low for the
duration of the watchdog timeout period (t ), WDO pulses low
WD
A1
3
A1
3
WDI
for the watchdog output pulse width, t
. The internal
WDO
watchdog timer clears whenever RST is de-asserted or
whenever WDI sees a falling edge.
Watchdog Output. WDO pulses low for the watchdog output
B1
B2
—
4
5
B1
—
4
—
5
WDO
MR
pulse width, t
, when the internal watchdog times out.
WDO
WDO is an open-drain output and requires a pull-up resistor.
Manual Reset Input. Drive MR low to manually reset the device.
RST remains asserted for the reset timeout period after MR is
released. MR is internally pulled up to VCC with a TBDkΩ
resistor.
Watchdog Enable Input. Drive WD_EN high to enable the
watchdog timer. Drive WD_EN low to disable the watchdog
timer.
—
B2
WD_EN
Reset Output. RST asserts when V
falls below the factory-set
CC
threshold. When V
goes above V + V
, RST remains
CC
TH
HYS
B3
6
B3
6
RST
asserted for the reset timeout period t
and then de-
RP
asserts. RST is an open-drain output and requires a pull up
resistor.
www.maximintegrated.com
Maxim Integrated | 9
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Functional Diagrams
MAX16152/MAX16153 Block Diagram
MR
MAX16152
MAX16153
V
V
CC
CC
V
CC
RST
RESET
TIMEOUT
PERIOD
V
CC
WDO
VOLTAGE
REFERENCE
WATCHDOG
TIMER
TRANSITION
DETECTOR
WDI
GND
www.maximintegrated.com
Maxim Integrated | 10
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Functional Diagrams (continued)
MAX16154/MAX16155 Block Diagram
MAX16154
V
CC
MAX16155
VCC
RST
RESET
TIMEOUT
PERIOD
V
CC
VOLTAGE
REFERENCE
WDO
WATCHDOG
TIMER
WD_EN
TRANSITION
DETECTOR
WDI
GND
www.maximintegrated.com
Maxim Integrated | 11
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Detailed Description
The MAX16152/MAX16153/MAX16154/MAX16155 are ultra-low-current supervisory circuits that monitor a single system
supply voltage and assert an active-low reset signal when the supply voltage drops below the factory-trimmed reset
threshold. After the supply voltage rises above the threshold voltage, the reset output remains asserted during the
reset timeout period, and finally asserts after the timeout period ends. In addition, a watchdog timer circuit monitors
microprocessor or microcontroller activity. During normal operation, the microprocessor or microcontroller toggles the
WDI input periodically with a valid logic transition (low to high or high to low). If the WDI input is toggled within
the watchdog timeout period (t
), the internal timer is cleared and restarted, and the WDO output remains high. If the
WD
input is not strobed before the timeout period expires, the watchdog output is asserted low for a period equal to the
watchdog output pulse width (t
).
WDO
Input Threshold
The MAX16152/MAX16153/MAX16154/MAX16155 monitor V
with ±2.5% accuracy across the full temperature and
CC
supply voltage ranges. The input threshold is programmable from 1.5V to 5V in approximately 100mV increments.
Contact Maxim for thresholds not listed in the Ordering Information table.
Watchdog
The MAX16152/MAX16153/MAX16154/MX16155 offer flexible watchdog circuits for monitoring microprocessor or
microcontroller activity. During normal operation, the internal timer is cleared and restarted each time the WDI input
undergoes a valid logic transition (high-to-low) within the selected timeout period (t ). The WDO remains high as long
WD
as the WDI input is strobed within the selected timeout period. If the WDI input is not strobed before the timeout period
expires, the watchdog output is asserted low for the watchdog output pulse width (t
). The MAX16154 and MAX16155
WDO
feature a logic input to enable/disable the watchdog timer during normal operation while the MAX16152 and MAX16153
does not. The watchdog timer for the MAX16152 and MAX16153 can be disabled by leaving the WDI floating.
Watchdog Startup Delay
All devices feature a factory-set startup delay. The startup delay provides an initial delay for the watchdog timer circuit
to power up and initialize before assuming responsibility for normal watchdog input monitoring. For the MAX16152 and
MAX16153, monitoring of the WDI input begins after the start-up time is complete. For the MAX16154 and MAX16155,
monitoring of the WDI input begins after the start-up delay if WD_EN is pulled high. To ensure that the system generates
no undesired watchdog outputs, the routine watchdog input transitions should begin before the minimum startup delay
period has expired. The startup delay is activated after the reset output is de-asserted. See the Selector Guide for
available watchdog startup delay options.
Watchdog Timeout Period
An open-drain, active-low watchdog output (WDO) asserts if a valid watchdog input transition is not received before the
timeout period elapses. See the Selector Guide for available watchdog timeout period options.
Watchdog Enable Input (WD_EN)
The MAX16154 and MAX16155 feature an active-high logic input (WD_EN) to enable or disable the watchdog function.
Applying a logic-low to WD_EN disables the watchdog function, causing the MAX16154 and MAX16155 to ignore any
signals applied to WDI. Applying a logic-high to WD_EN enables the watchdog function after 300μs (max) of set up time
t
. See Figure 1, Figure 2, and Figure 3 for more details.
SETUP
www.maximintegrated.com
Maxim Integrated | 12
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
V
TH
V
CC (MIN)
V
CC
WD_EN
tRP
RST
t
t
WD
STARTUP
t
WD
t
WD
WDI
A
B
E F
C
D
G
t
WDO
t
WDO
WDO
TRANSITION(S) ON WDI INGORED DURING STARTUP DELAY PERIOD.
A
B
WATCHDOG TIMER STARTS AFTER STARTUP DELAY AND WDO IS DEASSERTED.
C
TRANSITION ON WDI OCCURS BEFORE WATCHDOG TIMES OUT PERIOD. WATCHDOG TIMER CLEARS AND
D
RESTARTS TIMER EVERY TIME THERE IS A LOW TO HIGH OR HIGH TO LOW TRANSITION WITH tWD
.
E
F
WATCHDOG TIMES OUT, WDO ASSERTS AND THE NEXT WATCHDOG TIMER STARTS AT THE FALLING EDGE OF WDO.
TRANSITIONS ON WDI INGNORED WHEN WDO ASSERTED.
G
WATCHDOG TIMES OUT, WDO ASSERTS.
Figure 1. Watchdog Timing Characteristics with WD_EN Active During Power-Up
www.maximintegrated.com
Maxim Integrated | 13
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
V
TH
V
CC (MIN)
V
CC
WD_EN
tRP
RST
t
t
WD
STARTUP
t
WD
t
WD
WDI
A
B
E
F
G
C
D
t
WDO
t
WDO
WDO
TRANSITIONS ON WDI INGORED DURING tRP and tSTARTUP DELAY.
B
A
WATCHDOG TIMER STARTS AFTER STARTUP DELAY AND WD_EN IS DRIVEN HIGH.
C
D
TRANSITION ON WDI OCCURS BEFORE WATCHDOG TIMEOUT PERIOD. WATCHDOG TIMER CLEARS AND RESTARTS TIMER EVERY
TIME THERE IS A LOW TO HIGH OR HIGH TO LOW TRANSITION WITH tWD
.
E
F
WATCHDOG TIMES OUT, WDO ASSERTS AND THE NEXT WATCHDOG TIMER STARTS AT THE FALLING EDGE OF WDO.
TRANSITIONS ON WDI INGNORED WHEN WDO ASSERTED.
G
WATCHDOG TIMES OUT, WDO ASSERTS.
Figure 2. Watchdog Timing Characteristics with WD_EN Active During Startup
www.maximintegrated.com
Maxim Integrated | 14
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
V
TH
V
CC (MIN)
V
CC
WD_EN
tRP
RST
t
START-UP
t
WD
t
WD
WDI
A
B
D
C
E
F
G
H
t
WDO
t
WDO
WDO
A
B
C
D
E
TRANSITIONS ON WDI INGORED DURING tRP and tSTARTUP DELAY.
WATCHDOG DOES NOT START AFTER START-UP PERIOD SINCE WD_EN IS HELD LOW.
TRANSITION ON WDI IGNORED WHEN WD_EN IS HELD LOW.
WATCHDOG TIMER STARTS AFTER RISING EDGE ON WD_EN.
F
G
H
WATCHDOG TIMES OUT, WDO ASSERTS AND THE NEXT WATCHDOG TIMER STARTS AT THE FALLING EDGE OF WDO.
TRANSITION ON WDI IGNORED AFTER WDO ASSERTS.
WATCHDOG TIMES OUT, WDO ASSERTS.
Figure 3. Watchdog Timing Characteristics with WD_EN Active After Startup Time
Watchdog Input Signal
Watchdog timing is measured from the last WDI falling edge associated with a pulse of at least 1µs (min) in width.
WDI transitions are ignored when WDO and/or RST are asserted, and during the startup delay period. Watchdog input
transitions are also ignored for a setup period (t
) of up to 300μs after WD_EN is asserted.
SETUP
www.maximintegrated.com
Maxim Integrated | 15
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Reset Timeout Period
The MAX16152/MAX16153/MAX16154/MAX16155 feature an active-low open-drain reset output (RST) that asserts
low when V drops below the factory-set threshold voltage, V . The reset output remains asserted as long as
CC
TH
V
CC
remains below the threshold voltage. When V
rises above the threshold voltage plus the required hysteresis,
CC
the reset output remains asserted during the reset timeout period, and then de-asserts. See Figure 4 for more
details. Contact Maxim for reset timeout period options not listed in the Ordering Information table.
V
V
TH+ HYS
V
V
TH + HYS
V
TH
V
CC (MIN)
V
CC
t
t
RP
RP
RST
Figure 4. Reset Output Timing Diagram
Note: The reset timeout period does not include additional power up delay specified in the Electrical Characteristics table.
www.maximintegrated.com
Maxim Integrated | 16
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Manual Reset
The MAX16152 and the MAX16153 include an active-low manual reset input, MR. Forcing MR low asserts the reset
output after 250ns (typ) delay period (t ). The reset output remains asserted as long as MR is held low. The
MRD
reset output de-asserts after the reset timeout period when MR is released. See Figure 5 below for MR timing
characteristics. MR has an internal pullup resistor to V and can be left unconnected if not used.
CC
V
+ V
HYS
TH
V
CC (MIN)
V
CC
t
RP
t
RP
t
STARTUP
t
STARTUP
RST
WDI PULSES IGNORED
WDO
t < t
WD
WDI
MR
Figure 5. Manual Reset Input Timing Characteristics
www.maximintegrated.com
Maxim Integrated | 17
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Applications Information
Power Supply Bypassing
The MAX16152/MAX16153/MAX16154/MAX16155 operate from a 1.20V to 5.5V supply. Bypass V
to ground with a
CC
0.1μF capacitor as close to the device as possible to improve transient immunity. For fast-rising V
transients, additional
CC
capacitance may be required. V
rise time >50µs ensures proper operation.
CC
Watchdog Software Considerations
To help the watchdog timer monitor software execution more closely, set and reset the watchdog input at different points
in the program, rather than pulsing the watchdog input high-low-high or low-high-low. This technique avoids a stuck loop,
in which the watchdog timer would continue to be reset inside the loop, keeping the watchdog from timing out. Figure 6
shows an example of a flow diagram where the I/O driving the watchdog input is set high at the beginning of the program,
set low at the end of every subroutine or loop, then set high again when the program returns to the beginning. If the
program should hang in any subroutine, the problem would be quickly corrected, since the I/O is continually set low and
the watchdog timer is allowed to time out, causing WDO to pulse.
START
SET WDI
HIGH
PROGRAM
CODE
POSSIBLE INFINITE
LOOP PTH
SUBROUTINE OR
PROGRAM LOOP
SET WDI LOW
RETURN
Figure 6. Watchdog Flow Diagram
Negative-Going V
Transients Protection
CC
The MAX16152/MAX16153/MAX16154/MAX16155 are relatively immune to short-duration negative-going
transients (glitches). It is usually undesirable to reset the system when V experiences only small glitches. The
V
CC
CC
Typical Operating Characteristics show Maximum Transient Duration vs. Reset Threshold Overdrive, for which reset
pulses are not generated. The graph was produced using negative-going V
pulses, starting above V
and ending
TH
CC
www.maximintegrated.com
Maxim Integrated | 18
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
below the reset threshold by the magnitude indicated (reset threshold overdrive). The graph shows the maximum pulse
width that a negative-going V transient may typically have without causing a reset pulse to be issued. As the amplitude
CC
of the transient increases (i.e., goes farther below the reset threshold), the maximum allowable pulse width decreases. A
0.1µF bypass capacitor mounted close to the V
pin provides additional transient immunity.
CC
Selector Guide
MAX161__ __ __ __ __ +T
WD STARTUP
DELAY (MIN)
PACKAGE
WLP
VTH
1.5V
1.8V
2.5V
3.3V
5.0V
WD TIMEOUT
DELAY (MIN)
PART#
52
SUF
A
SUF
B
SUF
A
SUF
tRP (MIN)
100µs
100µs
A
B
C
D
1s
C
D
E
F
53
SOT23
WLP
B
16ms
128ms
256ms
B
C
D
4s
4s
54
C
16s
16s
64s
55
SOT23
D
64s
Ordering Information
PART NUMBER
MAX16152_ _ _ _ +T*
MAX16153_ _ _ _ +T*
MAX16154_ _ _ _+T*
MAX16155ABAD+T
TEMPERATURE RANGE
-40ºC to +125ºC
PIN-PACKAGE
6 WLP
-40ºC to +125ºC
6 SOT23
6 WLP
-40ºC to +125ºC
-40ºC to +125ºC
6 SOT23
Note: See the Selector Guide for reset timeout period, threshold voltage, watchdog start up delay, and watchdog timeout options. For
additional options and future products, please visit www.maximintegrated.com.
+ Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape-and-reel.
*Future product—Contact factory for availability.
www.maximintegrated.com
Maxim Integrated | 19
MAX16152/MAX16153/
MAX16154/MAX16155
nanoPower Supervisor and Watchdog Timer
Revision History
REVISION REVISION
PAGES
DESCRIPTION
CHANGED
NUMBER
DATE
0
4/19
Initial release
—
For pricing, delivery, and ordering information, please visit Maxim Integrated’s online storefront at https://www.maximintegrated.com/en/storefront/storefront.html.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max
limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
© 2018 Maxim Integrated Products, Inc.
相关型号：
©2020 ICPDF网 联系我们和版权申明