MAX3222EEUP+ [MAXIM]
±15kV ESD-Protected, Down to 10nA, 3.0V to 5.5V, Up to 1Mbps, True RS-232 Transceivers; ± 15kV ESD保护,低至10nA的, 3.0V至5.5V ,最高可达1Mbps,真RS- 232收发器型号: | MAX3222EEUP+ |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | ±15kV ESD-Protected, Down to 10nA, 3.0V to 5.5V, Up to 1Mbps, True RS-232 Transceivers |
文件: | 总22页 (文件大小:336K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
1±-12±8; Rev 12; 12/10
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
7/MAX3241E
General Description
Next-Generation Device Features
♦ For Space-Constrained Applications
MAX3228E/MAX3229E: ±±15k ESꢀ-ꢁrotectedꢂ
+2.1k to +1.1kꢂ RS-232 Transceivers in UCSꢁ
♦ For Low-koltage or ꢀata Cable Applications
MAX3380E/MAX338±E: +2.31k to +1.1kꢂ ±µAꢂ
2Tx/2Rxꢂ RS-232 Transceivers with ±±15k
ESꢀ-ꢁrotected I/O and Logic ꢁins
The MAX3222E/MAX3232E/MAX3237E/MAX3241E/
MAX3246E +3.0V-powered EIA/TIA-232 and V.28/V.24
communications interface devices feature low power con-
sumption, high data-rate capabilities, and enhanced
electrostatic-discharge (ESD) protection. The enhanced
ESD structure protects all transmitter outputs and
receiver inputs to ±1ꢀ5V using IEꢁ 1000-4-2 Air-ꢂap
Discharge, ±85V using IEꢁ 1000-4-2 ꢁontact Discharge
(±±5V for MAX3246E), and ±1ꢀ5V using the ꢃuman ꢄodꢅ
Model. The logic and receiver I/O pins of the MAX3237E
are protected to the above standards, while the transmit-
ter output pins are protected to ±1ꢀ5V using the ꢃuman
ꢄodꢅ Model.
Applications
ꢄatterꢅ-Powered Equipment
ꢁell Phones Smart Phones
ꢁell-Phone Data ꢁables
Noteboo5, Subnoteboo5, and Palmtop ꢁomputers
Printers
A proprietarꢅ low-dropout transmitter output stage delivers
true RS-232 performance from a +3.0V to +ꢀ.ꢀV power
supplꢅ, using an internal dual charge pump. The charge
pump requires onlꢅ four small 0.1µF capacitors for opera-
tion from a +3.3V supplꢅ. Each device guarantees opera-
tion at data rates of 2ꢀ05bps while maintaining RS-232
output levels. The MAX3237E guarantees operation at
2ꢀ05bps in the normal operating mode and 1Mbps in the
Megaꢄaud™ operating mode, while maintaining RS-232-
compliant output levels.
xDSL Modems
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
20 TQFN-EP**
(5mm x 5mm)
MAX3222ECTP+
0°C to +70°C
The MAX3222E/MAX3232E have two receivers and two
transmitters. The MAX3222E features a 1µA shutdown
mode that reduces power consumption in batterꢅ-pow-
ered portable sꢅstems. The MAX3222E receivers remain
active in shutdown mode, allowing monitoring of external
devices while consuming onlꢅ 1µA of supplꢅ current. The
MAX3222E and MAX3232E are pin, pac5age, and func-
tionallꢅ compatible with the industrꢅ-standard MAX242
and MAX232, respectivelꢅ.
MAX3222ECUP+
MAX3222ECAP+
MAX3222ECWN+
MAX3222ECPN+
MAX3222EC/D+
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
20 TSSOP
20 SSOP
18 Wide SO
18 Plastic DIP
Dice*
20 TQFN-EP**
(5mm x 5mm)
MAX3222EETP+
-40°C to +85°C
MAX3222EEUP/V+
MAX3222EEUP+
MAX3222EEAP+
MAX3222EEWN+
MAX3222EEPN+
MAX3232ECAE+
MAX3232ECWE+
MAX3232ECPE+
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
20 TSSOP
The MAX3241E/MAX3246E are complete serial ports
(three drivers/five receivers) designed for noteboo5 and
subnoteboo5 computers. The MAX3237E (five drivers/
three receivers) is ideal for peripheral applications that
require fast data transfer. These devices feature a shut-
down mode in which all receivers remain active, while
consuming onlꢅ 1µA (MAX3241E/MAX3246E) or 10nA
(MAX3237E).
20 TSSOP
20 SSOP
18 Wide SO
18 Plastic DIP
16 SSOP
16 Wide SO
16 Plastic DIP
/MAX3246E
The MAX3222E, MAX3232E, and MAX3241E are avail-
able in space-saving SO, SSOP, TQFN and TSSOP pac5-
ages. The MAX3237E is offered in an SSOP pac5age.
The MAX3246E is offered in the ultra-small 6 x 6 UꢁSP™
pac5age.
+Denotes a lead(Pb)-free/RoꢃS-compliant pac5age.
*Dice are tested at T = +2ꢀ°ꢁ, Dꢁ parameters onlꢅ.
**EP = Exposed pad.
/V denotes an automotive qualified part.
A
Ordering Information continued at end of data sheet.
Pin Configurations, Selector Guide, and Typical Operating
Circuits appear at end of data sheet.
Megaꢄaud and UꢁSP are trademar5s of Maxim Integrated
Products, Inc.
________________________________________________________________ Maxim Integrated Products
±
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim's website at www.maxim-ic.com.
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
ABSOLUTE MAXIMUM RATINGS
V
ꢁꢁ
to ꢂND..............................................................-0.3V to +6V
20-Pin TQFN (derate 21.3mW/°ꢁ above +70°ꢁ) ........1702mW
20-Pin TSSOP (derate 10.±mW/°ꢁ above +70°ꢁ) ........87±mW
20-Pin SSOP (derate 8.00mW/°ꢁ above +70°ꢁ) ..........640mW
28-Pin SSOP (derate ±.ꢀ2mW/°ꢁ above +70°ꢁ) ..........762mW
28-Pin Wide SO (derate 12.ꢀ0mW/°ꢁ above +70°ꢁ).............1W
28-Pin TSSOP (derate 12.8mW/°ꢁ above +70°ꢁ) ......1026mW
32-Pin TQFN (derate 33.3mW/°ꢁ above +70°ꢁ)...........2666mW
6 x 6 UꢁSP (derate 12.6mW/°ꢁ above +70°ꢁ).............1010mW
Operating Temperature Ranges
V+ to ꢂND (Note 1)..................................................-0.3V to +7V
V- to ꢂND (Note 1) ...................................................+0.3V to -7V
V+ + |V-| (Note 1).................................................................+13V
Input Voltages
T_IN, EN, SHDN, MꢄAUD to ꢂND ........................-0.3V to +6V
R_IN to ꢂND .....................................................................±2ꢀV
Output Voltages
T_OUT to ꢂND...............................................................±13.2V
R_OUT, R_OUTꢄ (MAX3237E/MAX3241E)...-0.3V to (V + 0.3V)
Short-ꢁircuit Duration, T_OUT to ꢂND.......................ꢁontinuous
MAX32_ _Eꢁ_ _ ...................................................0°ꢁ to +70°ꢁ
MAX32_ _EE_ _.................................................-40°ꢁ to +8ꢀ°ꢁ
Storage Temperature Range.............................-6ꢀ°ꢁ to +1ꢀ0°ꢁ
Lead Temperature (soldering, 10s) .................................+300°ꢁ
Soldering Temperature (reflow) .......................................+260°ꢁ
ꢄump Reflow Temperature (Note 2)
ꢁꢁ
/MAX3246E
ꢁontinuous Power Dissipation (T = +70°ꢁ)
A
16-Pin SSOP (derate 7.14mW/°ꢁ above +70°ꢁ) ..........ꢀ71mW
16-Pin TSSOP (derate ±.4mW/°ꢁ above +70°ꢁ) .......7ꢀ4.7mW
16-Pin TQFN (derate 20.8mW/°ꢁ above +70°ꢁ) .....1666.7mW
16-Pin Wide SO (derate ±.ꢀ2mW/°ꢁ above +70°ꢁ) .....762mW
18-Pin Wide SO (derate ±.ꢀ2mW/°ꢁ above +70°ꢁ) .....762mW
18-Pin PDIP (derate 11.11mW/°ꢁ above +70°ꢁ)..........88±mW
Infrared, 1ꢀs..................................................................+200°ꢁ
Vapor Phase, 20s..........................................................+21ꢀ°ꢁ
Note ±: V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V.
Note 2: This device is constructed using a unique set of pac5aging techniques that impose a limit on the thermal profile the device
can be exposed to during board-level solder attach and rewor5. This limit permits onlꢅ the use of the solder profiles recom-
mended in the industrꢅ-standard specification, JEDEꢁ 020A, paragraph 7.6, Table 3 for IR/VPR and convection reflow.
Preheating is required. ꢃand or wave soldering is not allowed.
Stresses beꢅond those listed under “Absolute Maximum Ratings” maꢅ cause permanent damage to the device. These are stress ratings onlꢅ, and functional
operation of the device at these or anꢅ other conditions beꢅond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods maꢅ affect device reliabilitꢅ.
ELECTRICAL CHARACTERISTICS
(V = +3V to +ꢀ.ꢀV, ꢁ1–ꢁ4 = 0.1µF, T = T
to T , unless otherwise noted. Tꢅpical values are at T = +2ꢀ°ꢁ.) (Notes 3, 4)
MAX A
ꢁꢁ
A
MIN
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
DC CHARACTERISTICS (V = +3.3V or +5V, T = +25°C)
CC
A
MAX3222E, MAX3232E,
MAX3241E, MAX3246E
0.3
1
Supply Current
SHDN = V , no load
mA
CC
MAX3237E
0.5
1
2.0
10
SHDN = GND
μA
nA
Shutdown Supply Current
SHDN = R_IN = GND, T_IN = GND or V (MAX3237E)
10
300
CC
LOGIC INPUTS
Input Logic Low
T_IN, EN, SHDN, MBAUD
0.8
V
V
V
V
V
= +3.3V
= +5.0V
2.0
2.4
CC
Input Logic High
T_IN, EN, SHDN, MBAUD
CC
Transmitter Input Hysteresis
Input Leakage Current
0.5
0.01
9
MAX3222E, MAX3232E,
MAX3241E, MAX3246E
T_IN, EN, SHDN
1
μA
T_IN, SHDN, MBAUD
MAX3237E (Note 5)
18
7/MAX3241E
2
_______________________________________________________________________________________
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
7/MAX3241E
ELECTRICAL CHARACTERISTICS (continued)
(V = +3V to +ꢀ.ꢀV, ꢁ1–ꢁ4 = 0.1µF, T = T
to T , unless otherwise noted. Tꢅpical values are at T = +2ꢀ°ꢁ.) (Notes 3, 4)
MAX A
ꢁꢁ
A
MIN
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
RECEIVER OUTPUTS
R_OUT (MAX3222E/MAX3237E/MAX3241E/
MAX3246E), EN = V , receivers disabled
Output Leakage Current
0.05
10
μA
V
CC
I
= 1.6mA (MAX3222E/MAX3232E/MAX3241E/
OUT
Output-Voltage Low
Output-Voltage High
0.4
MAX3246E), I
= 1.0mA (MAX3237E)
OUT
V
0.6
-
V
CC
-
CC
I
= -1.0mA
V
OUT
0.1
RECEIVER INPUTS
Input Voltage Range
-25
0.6
0.8
+25
V
V
V
CC
V
CC
V
CC
V
CC
= +3.3V
= +5.0V
= +3.3V
= +5.0V
1.1
1.5
1.5
2.0
0.5
5
Input Threshold Low
Input Threshold High
T
T
= +25°C
= +25°C
A
2.4
2.4
V
A
Input Hysteresis
V
Input Resistance
T
A
= +25°C
3
7
kꢀ
TRANSMITTER OUTPUTS
All transmitter outputs loaded with 3kꢀ to ground
(Note 6)
Output Voltage Swing
5
5.4
V
Output Resistance
V
CC
= 0V, transmitter output = 2V
300
50k
ꢀ
Output Short-Circuit Current
60
25
mA
V
= 0V or +3.0V to +5.5V, V
=
12V, transmitters
CC
OUT
Output Leakage Current
μA
V
disabled (MAX3222E/MAX3232E/MAX3241E/MAX3246E)
MOUSE DRIVABILITY (MAX3241E)
T1IN = T2IN = GND, T3IN = V , T3OUT loaded with
CC
3kꢀ to GND, T1OUT and T2OUT loaded with 2.5mA
Transmitter Output Voltage
5
each
ESD PROTECTION
Human Body Model
15
15
8
IEC 1000-4-2 Air-Gap Discharge (except MAX3237E)
IEC 1000-4-2 Contact Discharge (except MAX3237E)
IEC 1000-4-2 Contact Discharge (MAX3246E only)
Human Body Model
R_IN, T_OUT
kV
kV
±9
15
15
8
/MAX3246E
T_IN, R_IN, R_OUT, EN, SHDN,
MBAUD
MAX3237E
IEC 1000-4-2 Air-Gap Discharge
IEC 1000-4-2 Contact Discharge
_______________________________________________________________________________________
3
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
TIMING CHARACTERISTICS—MAX3222E/MAX3232E/MAX324±E/MAX3246E
(V = +3V to +ꢀ.ꢀV, ꢁ1–ꢁ4 = 0.1µF, T = T
to T , unless otherwise noted. Tꢅpical values are at T = +2ꢀ°ꢁ.) (Notes 3, 4)
MAX A
ꢁꢁ
A
MIN
PARAMETER
SYMBOL
CONDITIONS
= T
MIN
2ꢀ0
2ꢀ0
TYP
MAX
UNITS
T
to T
MAX
A
MIN
R = 35Ω,
ꢁ = 1000pF,
L
L
(MAX3222E/MAX3232E/
MAX3241E) (Note 6)
Maximum Data Rate
5bps
one transmitter
switching
T = +2ꢀ°ꢁ (MAX3246E)
A
t
t
0.1ꢀ
0.1ꢀ
200
200
100
ꢀ0
PꢃL
PLꢃ
Receiver input to receiver output,
ꢁ = 1ꢀ0pF
L
Receiver Propagation Delaꢅ
µs
/MAX3246E
Receiver Output Enable Time
Receiver Output Disable Time
Transmitter S5ew
Normal operation (except MAX3232E)
Normal operation (except MAX3232E)
(Note 7)
ns
ns
ns
ns
|t
|t
- t
|
|
PꢃL PLꢃ
Receiver S5ew
- t
PꢃL PLꢃ
V
ꢁꢁ
= +3.3V, T = +2ꢀ°ꢁ,
A
ꢁ = 1ꢀ0pF
L
to 1000pF
R = 35Ω to 75Ω, measured
from +3.0V to -3.0V or -3.0V to
L
Transition-Region Slew Rate
6
30
V/µs
+3.0V, one transmitter switching
TIMING CHARACTERISTICS—MAX3237E
(V
ꢁꢁ
= +3V to +ꢀ.ꢀV, ꢁ1–ꢁ4 = 0.1µF, T = T
A
to T
, unless otherwise noted. Tꢅpical values are at T = +2ꢀ°ꢁ.) (Note 3)
MAX A
MIN
PARAMETER
CONDITIONS
R = 35Ω, ꢁ = 1000pF, one transmitter switching,
MIN
TYP
MAX
UNITS
L
L
2ꢀ0
MꢄAUD = ꢂND
V
= +3.0V to +4.ꢀV, R = 35Ω, ꢁ = 2ꢀ0pF,
ꢁꢁ
L
L
Maximum Data Rate
1000
1000
5bps
one transmitter switching, MꢄAUD = V
ꢁꢁ
V
= +4.ꢀV to +ꢀ.ꢀV, R = 35Ω, ꢁ = 1000pF,
ꢁꢁ
L
L
one transmitter switching, MꢄAUD = V
ꢁꢁ
t
t
0.1ꢀ
0.1ꢀ
2.6
PꢃL
PLꢃ
Receiver Propagation Delaꢅ
R_IN to R_OUT, ꢁ = 1ꢀ0pF
L
µs
Receiver Output Enable Time
Receiver Output Disable Time
Normal operation
Normal operation
µs
µs
2.4
|t
|t
|t
- t
|, MꢄAUD = ꢂND
PꢃL PLꢃ
Transmitter S5ew (Note 7)
Receiver S5ew
100
ꢀ0
ns
ns
- t
|, MꢄAUD = V
|
PꢃL PLꢃ
ꢁꢁ
- t
PꢃL PLꢃ
V
= +3.3V,
ꢁꢁ
MꢄAUD = ꢂND
MꢄAUD = V
6
24
4
30
1ꢀ0
30
ꢁ = 1ꢀ0pF
L
to 1000pF
R = 35Ω to 75Ω,
+3.0V to -3.0V or
-3.0V to +3.0V,
L
Transition-Region Slew Rate
V/µs
ꢁꢁ
ꢁ = 1ꢀ0pF to 2ꢀ00pF,
L
T
A
= +2ꢀ°ꢁ
MꢄAUD = ꢂND
Note 3:MAX3222E/MAX3232E/MAX3241E: ꢁ1–ꢁ4 = 0.1µF tested at +3.3V ±10ꢆ; ꢁ1 = 0.047µF, ꢁ2, ꢁ3, ꢁ4 = 0.33µF tested at +ꢀ.0V
±10ꢆ. MAX3237E: ꢁ1–ꢁ4 = 0.1µF tested at +3.3V ±ꢀꢆ, ꢁ1–ꢁ4 = 0.22µF tested at +3.3V ±10ꢆ; ꢁ1 = 0.047µF, ꢁ2, ꢁ3, ꢁ4 =
0.33µF tested at +ꢀ.0V ±10ꢆ. MAX3246E: ꢁ1-ꢁ4 = 0.22µF tested at +3.3V ±10ꢆ; ꢁ1 = 0.22µF, ꢁ2, ꢁ3, ꢁ4 = 0.ꢀ4µF tested at
+ꢀ.0V ±10ꢆ.
Note 4:MAX3246E devices are production tested at +2ꢀ°ꢁ. All limits are guaranteed bꢅ design over the operating temperature range.
Note 1:The MAX3237E logic inputs have an active positive feedbac5 resistor. The input current goes to zero when the inputs are at
the supplꢅ rails.
Note 6: MAX3241EEUI is specified at T = +2ꢀ°ꢁ.
A
7/MAX3241E
Note 7: Transmitter s5ew is measured at the transmitter zero crosspoints.
4
_______________________________________________________________________________________
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
7/MAX3241E
__________________________________________Typical Operating Characteristics
(V
ꢁꢁ
= +3.3V, 2ꢀ05bps data rate, 0.1µF capacitors, all transmitters loaded with 35Ω and ꢁ , T = +2ꢀ°ꢁ, unless otherwise noted.)
L A
MAX3222E/MAX3232E
OPERATING SUPPLY CURRENT
vs. LOAD CAPACITANCE
MAX3222E/MAX3232E
TRANSMITTER OUTPUT VOLTAGE
vs. LOAD CAPACITANCE
MAX3222E/MAX3232E
SLEW RATE vs. LOAD CAPACITANCE
16
14
12
10
8
45
6
T1 TRANSMITTING AT 250kbps
T2 TRANSMITTING AT 15.6kbps
5
4
V
OUT+
40
35
30
25
20
-SLEW
+SLEW
3
250kbps
120kbps
T1 TRANSMITTING AT 250kbps
T2 TRANSMITTING AT 15.6kbps
2
1
0
-1
-2
-3
-4
-5
-6
6
20kbps
15
10
5
4
V
2
OUT-
FOR DATA RATES UP TO 250kbps
0
0
0
1000
2000
3000
4000
5000
0
1000
2000
3000
4000
5000
0
1000
2000
3000
4000
5000
LOAD CAPACITANCE (pF)
LOAD CAPACITANCE (pF)
LOAD CAPACITANCE (pF)
MAX3241E
TRANSMITTER OUTPUT VOLTAGE
vs. LOAD CAPACITANCE
MAX3241E
OPERATING SUPPLY CURRENT
vs. LOAD CAPACITANCE
MAX3241E
SLEW RATE vs. LOAD CAPACITANCE
6
5
14
60
50
40
30
20
10
0
1 TRANSMITTER AT 250kbps
2 TRANSMITTERS AT 15.6kbps
V
OUT+
12
10
8
4
250kbps
3
1 TRANSMITTER AT 250kbps
2 TRANSMITTERS AT 15.6kbps
2
120kbps
1
0
6
-1
-2
-3
-4
-5
-6
20kbps
4
2
V
OUT-
0
0
1000
2000
3000
4000
5000
0
1000
2000
3000
4000
5000
0
1000
2000
3000
4000
5000
LOAD CAPACITANCE (pF)
LOAD CAPACITANCE (pF)
LOAD CAPACITANCE (pF)
MAX3237E
TRANSMITTER OUTPUT VOLTAGE
vs. LOAD CAPACITANCE
MAX3237E
TRANSMITTER OUTPUT VOLTAGE
vs. LOAD CAPACITANCE (MBAUD = GND)
MAX3237E
TRANSMITTER OUTPUT VOLTAGE
vs. LOAD CAPACITANCE (MBAUD = V
)
CC
6
5
4
3
2
1
7.5
5.0
2.5
0
6
5
1Mbps
V
OUT+
V
+
OUT
4
/MAX3246E
FOR DATA RATES UP TO 250kbps
1 TRANSMITTER AT 250kbps
4 TRANSMITTERS AT 15.6kbps
ALL TRANSMITTERS LOADED
2Mbps
1.5Mbps
3
2
FOR DATA RATES UP TO 250kbps
1 TRANSMITTER 250kbps
1 TRANSMITTER AT FULL DATA RATE
4 TRANSMITTERS AT 1/16 DATA RATE
3kΩ + C LOAD, EACH OUTPUT
1
WITH 3kΩ + C
L
0
4 TRANSMITTERS 15.6kbps
ALL TRANSMITTERS LOADED
0
L
-1
-2
-3
-1
-2
-3
-4
-5
-6
WITH 3kΩ + C
L
-2.5
-5.0
-7.5
1.5Mbps
1Mbps
2Mbps
-4
-5
V
OUT-
V
OUT-
-6
0
500 1000 1500 2000 2500 3000
LOAD CAPACITANCE (pF)
0
500
1000
1500
2000
0
500 1000 1500 2000 2500 3000
LOAD CAPACITANCE (pF)
LOAD CAPACITANCE (pF)
_______________________________________________________________________________________
1
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
Typical Operating Characteristics (continued)
(V
ꢁꢁ
= +3.3V, 2ꢀ05bps data rate, 0.1µF capacitors, all transmitters loaded with 35Ω and ꢁ , T = +2ꢀ°ꢁ, unless otherwise noted.)
L A
MAX3237E
SUPPLY CURRENT vs. LOAD CAPACITANCE
WHEN TRANSMITTING DATA (MBAUD = GND)
MAX3237E
SLEW RATE vs. LOAD CAPACITANCE
(MBAUD = GND)
MAX3237E
SLEW RATE vs. LOAD CAPACITANCE
(MBAUD = V
)
CC
50
12
10
70
60
50
40
30
20
250kbps
120kbps
40
30
20
10
0
-SLEW, 1Mbps
+SLEW, 1Mbps
-SLEW, 2Mbps
+SLEW, 2Mbps
SR-
SR+
8
20kbps
/MAX3246E
6
4
1 TRANSMITTER AT 20kbps, 120kbps, 250kbps
4 TRANSMITTERS AT 15.6kbps
ALL TRANSMITTERS LOADED
1 TRANSMITTER AT 250kbps
4 TRANSMITTERS AT 15.6kbps
ALL TRANSMITTERS LOADED
1 TRANSMITTER AT FULL DATA RATE
4 TRANSMITTERS AT 1/16 DATA RATE
2
0
10
0
3kΩ + C LOAD EACH OUTPUT
WITH 3kΩ + C
L
L
WITH 3kΩ + C
L
0
500
1000
1500
2000
0
500
1000 1500 2000 2500 3000
LOAD CAPACITANCE (pF)
0
500
1000 1500 2000 2500 3000
LOAD CAPACITANCE (pF)
LOAD CAPACITANCE (pF)
MAX3237E
TRANSMITTER OUTPUT VOLTAGE
vs. SUPPLY VOLTAGE (MBAUD = GND)
MAX3237E
MAX3237E SUPPLY CURRENT
vs. SUPPLY VOLTAGE (MBAUD = GND)
TRANSMITTER SKEW vs. LOAD CAPACITANCE
(MBAUD = V
)
CC
100
50
6
5
V
+
OUT
4
80
60
40
20
0
40
30
3
2
1 TRANSMITTER AT 250kbps
4 TRANSMITTERS AT 15.6kbps
ALL TRANSMITTERS LOADED
WITH 3kΩ + 1000pF
1
0
-1
-2
-3
-4
-5
-6
20
1 TRANSMITTER AT 250kbps
4 TRANSMITTERS AT 15.6kbps
ALL TRANSMITTERS LOADED
WITH 3kΩ AND 1000pF
|tPLH - t
|
PHL
1 TRANSMITTER AT 500kbps
4 TRANSMITTERS AT 1/16 DATA RATE
ALL TRANSMITTERS LOADED
10
0
V
OUT-
4.5
WITH 3kΩ + C
L
0
500
1000
1500
2000
2.0
2.5
3.0
3.5
4.0
4.5
5.0
2.0
2.5
3.0
3.5
4.0
5.0
LOAD CAPACITANCE (pF)
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
MAX3246E
OPERATING SUPPLY CURRENT
vs. LOAD CAPACITANCE
MAX3246E
TRANSMITTER OUTPUT VOLTAGE
vs. LOAD CAPACITANCE
MAX3246E
SLEW RATE vs. LOAD CAPACITANCE
60
55
50
45
40
35
30
25
20
15
10
5
7
6
5
4
3
2
1
0
16
14
1 TRANSMITTER AT 250kbps
2 TRANSMITTERS AT 15.6kbps
V
OUT+
1 TRANSMITTER AT 250kbps
2 TRANSMITTERS AT 15.6kbps
12
250kbps
120kbps
SR-
SR+
10
8
-1
-2
-3
-4
-5
-6
20kbps
6
4
V
OUT-
0
0
1000
2000
3000
4000
5000
0
1000
2000
3000
4000
5000
0
1000
2000
3000
4000
5000
LOAD CAPACITANCE (pF)
LOAD CAPACITANCE (pF)
LOAD CAPACITANCE (pF)
7/MAX3241E
6
_______________________________________________________________________________________
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
7/MAX3241E
ꢂin Description
PIN
MAX3222E
SO/ TSSOP/
MAX3232E
MAX3241E
MAX3237E SSOP/
SO/DIP/
SSOP/
NAME
FUNCTION
MAX3246E
20-PIN
TQFN
TQFN
SO/ TQFN
TSSOP
DIP SSOP
16-PIN TSSOP
TSSOP
Receiver Enable. Active
low.
1±
1
1
—
—
—
13*
23
22
ꢄ3
EN
Positive Terminal of
Voltage-Doubler ꢁharge-
Pump ꢁapacitor
1
2
3
2
3
16
1ꢀ
1
2
2
3
28
27
28
27
28
27
F3
F1
ꢁ1+
V+
+ꢀ.ꢀV ꢂenerated bꢅ the
ꢁharge Pump
20
Negative Terminal of
Voltage-Doubler ꢁharge-
Pump ꢁapacitor
2
3
4
ꢀ
4
ꢀ
1
2
3
4
4
ꢀ
2ꢀ
1
24
1
23
2±
F4
E1
ꢁ1-
Positive Terminal of
Inverting ꢁharge-Pump
ꢁapacitor
ꢁ2+
Negative Terminal of
Inverting ꢁharge-Pump
ꢁapacitor
4
ꢀ
6
7
6
7
3
4
ꢀ
6
6
7
3
4
2
3
30
31
D1
ꢁ1
ꢁ2-
V-
-ꢀ.ꢀV ꢂenerated bꢅ the
ꢁharge Pump
±,
10,
11
6,
7,
8
8,
1ꢀ
ꢀ,
12
ꢀ, 6, 7,
10, 12
F6, E6,
D6
RS-232 Transmitter
Outputs
6, 1ꢀ
8, 17
7, 14
8, 17
T_OUT
A4, Aꢀ,
A6, ꢄ6,
ꢁ6
±,
6,
7, 14
8, 13
±, 16
10, 1ꢀ
12, 13
8, 13
±, 12
±, 16
8, ±, 11
4–8
1–ꢀ
R_IN
R_OUT
T_IN
RS-232 Receiver Inputs
14
11
13,
14,
1ꢀ,
ꢁ2, ꢄ1,
A1, A2,
A3
10,
13
7,
10
12,
1ꢀ
18, 20,
21
TTL/ꢁMOS Receiver
Outputs
1ꢀ–1±
17, 18
17*, 1±*,
22*, 23*,
24*
10,
11,
12
12,
13,
14
/MAX3246E
11,
12
13,
14
E3, E2,
D2
TTL/ꢁMOS Transmitter
Inputs
10, 11
8, ±
10, 11
*These pins have an active positive feedbac5 resistor internal to the MAX3237E, allowing unused inputs to be left unconnected.
_______________________________________________________________________________________
7
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
ꢂin Description (continued)
PIN
MAX3222E
SO/ TSSOP/
MAX3232E
MAX3241E
SO/DIP/
SSOP/
16-PIN
TSSOP
NAME
FUNCTION
SSOP/
SO/ TQFN
TSSOP
MAX3237E
MAX3246E
20-PIN
TSSOP
TQFN
TQFN
DIP SSOP
16
17
16
17
18
1±
13
14
1ꢀ
18
1±
2
2ꢀ
26
24
26
Fꢀ
F2
ꢂND
ꢂround
+3.0V to +ꢀ.ꢀV Supplꢅ
Voltage
/MAX3246E
V
16
26
ꢁꢁ
Shutdown ꢁontrol. Active
low.
18
18
—
20
—
—
—
—
—
14*
—
22
—
21
ꢄ2
SHDN
No ꢁonnection. For
MAX3246E, these
locations are not
populated with solder
bumps.
ꢁ3, D3, ꢄ4,
ꢁ4, D4, E4,
ꢄꢀ, ꢁꢀ, Dꢀ,
Eꢀ
±, 16,
2ꢀ,
32
1, 10,
11, 20
±, 12
11, 14
N.ꢁ.
Megaꢄaud ꢁontrol Input.
ꢁonnect to ꢂND for
normal operation; connect
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1ꢀ*
16
—
—
—
1±, 20
—
—
—
—
MꢄAUD
R_OUTꢄ
EP
to V
for 1Mbps
ꢁꢁ
transmission rates.
Noninverting
ꢁomplementarꢅ Receiver
Outputs. Alwaꢅs active.
20,
21
Exposed Pad. Solder the
exposed pad to the
ground plane or leave
unconnected (for TQFN
onlꢅ).
—
7/MAX3241E
8
_______________________________________________________________________________________
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
7/MAX3241E
V
V
CC
CC
0.1μF
0.1μF
V
V
CC
CC
C1+
C1+
V+
V-
V+
V-
C1
C2
C1
C2
C3
C4
C3
C4
C1-
C2+
C1-
C2+
MAX3222E
MAX3232E
MAX3237E
MAX3241E
MAX3246E
MAX3222E
MAX3232E
MAX3237E
MAX3241E
MAX3246E
C2-
C2-
T_ OUT
R_ IN
T_ OUT
R_ IN
T_ IN
T_ IN
R_ OUT
R_ OUT
5kΩ
5kΩ
1000pF
(2500pF, MAX3237E only)
7kΩ
150pF
3kΩ
GND
GND
MINIMUM SLEW-RATE TEST CIRCUIT
Figure 1. Slew-Rate Test ꢁircuits
MAXIMUM SLEW-RATE TEST CIRCUIT
into a high-impedance state when the device is in shut-
down mode (SHDN = ꢂND). The MAX3222E/
MAX3232E/MAX3237E/MAX3241E/MAX3246E permit
the outputs to be driven up to ±12V in shutdown.
Detailed Description
Dual Charge-ꢂump koltage Converter
The MAX3222E/MAX3232E/MAX3237E/MAX3241E/
MAX3246E’s internal power supplꢅ consists of a regu-
lated dual charge pump that provides output voltages
of +ꢀ.ꢀV (doubling charge pump) and -ꢀ.ꢀV (inverting
The MAX3222E/MAX3232E/MAX3241E/MAX3246E
transmitter inputs do not have pullup resistors. ꢁonnect
unused inputs to ꢂND or V . The MAX3237E’s trans-
ꢁꢁ
charge pump) over the +3.0V to +ꢀ.ꢀV V
range. The
ꢁꢁ
mitter inputs have a 4005Ω active positive-feedbac5
charge pump operates in discontinuous mode; if the
output voltages are less than ꢀ.ꢀV, the charge pump is
enabled, and if the output voltages exceed ꢀ.ꢀV, the
charge pump is disabled. Each charge pump requires
a flꢅing capacitor (ꢁ1, ꢁ2) and a reservoir capacitor
(ꢁ3, ꢁ4) to generate the V+ and V- supplies (Figure 1).
resistor, allowing unused inputs to be left unconnected.
MAX3237E MegaBaud Operation
For higher-speed serial communications, the
MAX3237E features Megaꢄaud operation. In
Megaꢄaud operating mode (MꢄAUD = V ), the
ꢁꢁ
MAX3237E transmitters guarantee a 1Mbps data rate
Rꢁ-232 Transmitters
The transmitters are inverting level translators that con-
vert TTL/ꢁMOS-logic levels to ±ꢀV EIA/TIA-232-compli-
ant levels.
with worst-case loads of 35Ω in parallel with 2ꢀ0pF for
+3.0V < V
< +4.ꢀV. For +ꢀV ±10ꢆ operation, the
ꢁꢁ
MAX3237E transmitters guarantee a 1Mbps data rate
/MAX3246E
into worst-case loads of 35Ω in parallel with 1000pF.
The MAX3222E/MAX3232E/MAX3237E/MAX3241E/
MAX3246E transmitters guarantee a 2ꢀ05bps data rate
with worst-case loads of 35Ω in parallel with 1000pF,
providing compatibilitꢅ with Pꢁ-to-Pꢁ communication
software (such as LapLin5™). Transmitters can be par-
alleled to drive multiple receivers or mice.
Rꢁ-232 Receivers
The receivers convert RS-232 signals to ꢁMOS-logic
output levels. The MAX3222E/MAX3237E/MAX3241E/
MAX3246E receivers have inverting three-state outputs.
Drive EN high to place the receiver(s) into a high-
impedance state. Receivers can be either active or
inactive in shutdown (Table 1).
The MAX3222E/MAX3237E/MAX3241E/MAX3246E
transmitters are disabled and the outputs are forced
LapLin5 is a trademar5 of Traveling Software.
_______________________________________________________________________________________
9
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
V
CC
5V/div
0
SHDN
T2OUT
PREVIOUS
RS-232
V
CC
PROTECTION
2V/div
0
DIODE
Rx
5kΩ
/MAX3246E
UART
T1OUT
V
= 3.3V
Tx
CC
C1–C4 = 0.1μF
GND
SHDN = GND
40μs/div
Figure 3. Transmitter Outputs Recovering from Shutdown or
Powering Up
a) OLDER RS-232: POWERED-DOWN UART DRAWS CURRENT FROM
AA ACTIVE RECEIVER OUTPUT IN SHUTDOWN.
V
CC
TO
μP
MAX3222E/MAX3237E/MAX3241E/
MAX3246E ꢁhutdown Mode
Supplꢅ current falls to less than 1µA in shutdown mode
(SHDN = low). The MAX3237E’s supplꢅ current falls
to10nA (tꢅp) when all receiver inputs are in the invalid
range (-0.3V < R_IN < +0.3V). When shut down, the
device’s charge pumps are shut off, V+ is pulled down
to V , V- is pulled to ground, and the transmitter out-
ꢁꢁ
puts are disabled (high impedance). The time required
to recover from shutdown is tꢅpicallꢅ 100µs, as shown
LOGIC
TRANSITION
DETECTOR
MAX3237E/MAX3241E
R1OUTB
V
CC
PROTECTION
DIODE
R1IN
Rx
R1OUT
THREE-STATED
in Figure 3. ꢁonnect SHDN to V
if shutdown mode is
ꢁꢁ
EN = V
CC
5kΩ
not used. SHDN has no effect on R_OUT or R_OUTꢄ
UART
(MAX3237E/MAX3241E).
T1OUT
T1IN
Tx
1ꢀ5k EꢁD ꢂrotection
As with all Maxim devices, ESD-protection structures
are incorporated to protect against electrostatic dis-
charges encountered during handling and assemblꢅ.
The driver outputs and receiver inputs of the
MAX3222E/MAX3232E/MAX3237E/MAX3241E/MAX3246E
have extra protection against static electricitꢅ. Maxim’s
engineers have developed state-of-the-art structures to
protect these pins against ESD of ±1ꢀ5V without damage.
The ESD structures withstand high ESD in all states:
normal operation, shutdown, and powered down. After
an ESD event, Maxim’s E versions 5eep wor5ing without
latchup, whereas competing RS-232 products can latch
and must be powered down to remove latchup.
GND
SHDN = GND
b) NEW MAX3237E/MAX3241E: EN SHUTS DOWN RECEIVER OUTPUTS
B (EXCEPT FOR B OUTPUTS), SO NO CURRENT FLOWS TO UART IN SHUTDOWN.
B B OUTPUTS INDICATE RECEIVER ACTIVITY DURING SHUTDOWN WITH EN HIGH.
Figure 2. Detection of RS-232 Activitꢅ when the UART and
Interface are Shut Down; ꢁomparison of MAX3237E/MAX3241E
(b) with Previous Transceivers (a)
The complementarꢅ outputs on the MAX3237E/
MAX3241E (R_OUTꢄ) are alwaꢅs active, regardless of the
state of EN or SHDN. This allows the device to be used
for ring indicator applications without forward biasing
other devices connected to the receiver outputs. This is
ideal for sꢅstems where V
to accommodate peripherals such as UARTs (Figure 2).
Furthermore, the MAX3237E logic I/O pins also have
±1ꢀ5V ESD protection. Protecting the logic I/O pins to
±1ꢀ5V ma5es the MAX3237E ideal for data cable
applications.
drops to zero in shutdown
ꢁꢁ
7/MAX3241E
±0 ______________________________________________________________________________________
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
7/MAX3241E
ESD protection can be tested in various waꢅs; the
Table ±. MAX3222E/MAX3237E/MAX324±E/
transmitter outputs and receiver inputs for the
MAX3246E Shutdown and Enable Control
MAX3222E/MAX3232E/MAX3241E/MAX3246E are
characterized for protection to the following limits:
Truth Table
• ±1ꢀ5V using the ꢃuman ꢄodꢅ Model
R_OUTB
(MAX3237E/
MAX3241E)
SHDN
EN
T_OUT
R_OUT
• ±85V using the ꢁontact Discharge method specified
in IEꢁ 1000-4-2
• ±±5V (MAX3246E onlꢅ) using the ꢁontact Discharge
method specified in IEꢁ 1000-4-2
ꢃigh
impedance
0
0
Active
Active
• ±1ꢀ5V using the Air-ꢂap Discharge method speci-
fied in IEꢁ 1000-4-2
ꢃigh
impedance
ꢃigh
impedance
0
1
1
1
0
1
Active
Active
Active
Active
Active
ꢃigh
impedance
Active
R
C
R
D
1MΩ
1500Ω
I
P
100%
90%
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
I
r
DISCHARGE
RESISTANCE
CHARGE-CURRENT-
LIMIT RESISTOR
AMPERES
36.8%
HIGH-
VOLTAGE
DC
DEVICE-
UNDER-
TEST
C
100pF
STORAGE
CAPACITOR
s
10%
0
SOURCE
TIME
0
t
RL
t
DL
CURRENT WAVEFORM
Figure 4b. ꢃuman ꢄodꢅ Model ꢁurrent Waveform
Figure 4a. ꢃuman ꢄodꢅ ESD Test Model
I
100%
R
R
D
330Ω
C
90%
50MΩ to 100MΩ
DISCHARGE
RESISTANCE
CHARGE-CURRENT-
LIMIT RESISTOR
HIGH-
VOLTAGE
DC
DEVICE-
UNDER-
TEST
/MAX3246E
C
s
150pF
STORAGE
CAPACITOR
SOURCE
10%
t
t = 0.7ns to 1ns
r
30ns
60ns
Figure ꢀa. IEꢁ 1000-4-2 ESD Test Model
Figure ꢀb. IEꢁ 1000-4-2 ESD ꢂenerator ꢁurrent Waveform
______________________________________________________________________________________ ±±
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
Table 2. Required Minimum Capacitor
6
kalues
5
V
C1
C2, C3, C4
(µF)
V
OUT+
4
3
CC
V
= 3.0V
CC
(V)
(µF)
2
MAX3222E/MAX3232E/MAX3241E
V
V
1
OUT+
OUT-
3.0 to 3.6
4.ꢀ to ꢀ.ꢀ
0.1
0.047
0.1
0.1
0
0.33
0.47
-1
-2
-3
-4
-5
-6
3.0 to ꢀ.ꢀ
V
CC
1
/MAX3246E
MAX3237E/MAX3246E
3.0 to 3.6
V
OUT-
9
0.22
0.1
0.22
0.1
3.1ꢀ to 3.6
0
2
3
4
5
6
7
8
10
4.ꢀ to ꢀ.ꢀ
0.047
0.22
0.33
1.0
LOAD CURRENT PER TRANSMITTER (mA)
3.0 to ꢀ.ꢀ
Figure 6a. MAX3241E Transmitter Output Voltage vs. Load
ꢁurrent Per Transmitter
Table 3. Logic-Family Compatibility with
karious Supply koltages
IEC 1000-4-2
SYSTEM
V
SUPPLY
VOLTAGE
(V)
CC
The IEꢁ 1000-4-2 standard covers ESD testing and
performance of finished equipment; it does not specifi-
callꢅ refer to integrated circuits. The MAX3222E/
MAX3232E/MAX3237E/MAX3241E/MAX3246E help ꢅou
design equipment that meets level 4 (the highest level)
of IEꢁ 1000-4-2, without the need for additional ESD-
protection components.
POWER-SUPPLY
VOLTAGE
(V)
COMPATIBILITY
ꢁompatible with all
ꢁMOS families
3.3
ꢀ
3.3
ꢀ
ꢁompatible with all
TTL and ꢁMOS
families
The major difference between tests done using the
ꢃuman ꢄodꢅ Model and IEꢁ 1000-4-2 is higher pea5
current in IEꢁ 1000-4-2, because series resistance is
lower in the IEꢁ 1000-4-2 model. ꢃence, the ESD with-
stand voltage measured to IEꢁ 1000-4-2 is generallꢅ
lower than that measured using the ꢃuman ꢄodꢅ
Model. Figure ꢀa shows the IEꢁ 1000-4-2 model, and
Figure ꢀb shows the current waveform for the ±85V IEꢁ
1000-4-2 level 4 ESD ꢁontact Discharge test. The Air-
ꢂap Discharge test involves approaching the device
with a charged probe. The ꢁontact Discharge method
connects the probe to the device before the probe is
energized.
ꢁompatible with AꢁT
and ꢃꢁT ꢁMOS, and
with Aꢁ, ꢃꢁ, or
ꢀ
3.3
ꢁD4000 ꢁMOS
For the MAX3237E, all logic and RS-232 I/O pins are
characterized for protection to ±1ꢀ5V per the ꢃuman
ꢄodꢅ Model.
EꢁD Test Conditions
ESD performance depends on a varietꢅ of conditions.
ꢁontact Maxim for a reliabilitꢅ report that documents
test setup, test methodologꢅ, and test results.
Machine Model
The Machine Model for ESD tests all pins using a
200pF storage capacitor and zero discharge resis-
tance. Its objective is to emulate the stress caused bꢅ
contact that occurs with handling and assemblꢅ during
manufacturing. All pins require this protection during
manufacturing, not just RS-232 inputs and outputs.
Therefore, after Pꢁ board assemblꢅ, the Machine
Model is less relevant to I/O ports.
Human Body Model
Figure 4a shows the ꢃuman ꢄodꢅ Model, and Figure
4b shows the current waveform it generates when dis-
charged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of interest,
which is then discharged into the test device through a
1.ꢀ5Ω resistor.
7/MAX3241E
±2 ______________________________________________________________________________________
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
7/MAX3241E
V
CC
= +3.0V TO +5.5V
C
BYPASS
26
27
3
28
V
CC
C1+
V+
V-
C1
C3
C4
24
C1-
COMPUTER SERIAL PORT
1
C2+
MAX3241E
C2
2
C2-
9
T1IN
14
13
T1OUT
T2OUT
T3OUT
+V
+V
T2IN
10
11
T3IN
12
21
V
CC
-V
R1OUTB
GND
Tx
20
19
R2OUTB
R1OUT
R1IN
R2IN
R3IN
R4IN
4
5
6
5kΩ
18
17
16
R2OUT
R3OUT
5kΩ
5kΩ
5kΩ
5kΩ
7
R4OUT
R5OUT
EN
MOUSE
15
23
R5IN
8
22
SHDN
V
CC
GND
25
Figure 6b. Mouse Driver Test ꢁircuit
excessivelꢅ with temperature. If in doubt, use capaci-
tors with a larger nominal value. The capacitor’s equiv-
alent series resistance (ESR), which usuallꢅ rises at low
temperatures, influences the amount of ripple on V+
and V-.
Applications Information
Capacitor ꢁelection
The capacitor tꢅpe used for ꢁ1–ꢁ4 is not critical for
proper operation; polarized or nonpolarized capacitors
can be used. The charge pump requires 0.1µF capaci-
tors for 3.3V operation. For other supplꢅ voltages, see
Table 2 for required capacitor values. Do not use val-
ues smaller than those listed in Table 2. Increasing the
capacitor values (e.g., bꢅ a factor of 2) reduces ripple
on the transmitter outputs and slightlꢅ reduces power
consumption. ꢁ2, ꢁ3, and ꢁ4 can be increased without
changing ꢁ1’s value. Howeverꢂ do not increase C±
without also increasing the values of C2ꢂ C3ꢂ C4ꢂ
ꢂower-ꢁupply Decoupling
In most circumstances, a 0.1µF V
bꢅpass capacitor
/MAX3246E
ꢁꢁ
is adequate. In applications sensitive to power-supplꢅ
noise, use a capacitor of the same value as charge-
pump capacitor ꢁ1. ꢁonnect bꢅpass capacitors as
close to the Iꢁ as possible.
Operation Down to 2.7k
Transmitter outputs meet EIA/TIA-ꢀ62 levels of ±3.7V
with supplꢅ voltages as low as 2.7V.
and C
to maintain the proper ratios (C± to
BYꢁASS
the other capacitors).
When using the minimum required capacitor values,
ma5e sure the capacitor value does not degrade
______________________________________________________________________________________ ±3
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
the transmitters are enabled onlꢅ when the magnitude
of V- exceeds approximatelꢅ -3.0V.
Transmitter Outputs Recovering
from ꢁhutdown
Figure 3 shows two transmitter outputs recovering from
shutdown mode. As theꢅ become active, the two trans-
mitter outputs are shown going to opposite RS-232 levels
(one transmitter input is high; the other is low). Each
transmitter is loaded with 35Ω in parallel with 2ꢀ00pF.
The transmitter outputs displaꢅ no ringing or undesir-
able transients as theꢅ come out of shutdown. Note that
Mouse Drivability
The MAX3241E is designed to power serial mice while
operating from low-voltage power supplies. It has
been tested with leading mouse brands from manu-
facturers such as Microsoft and Logitech. The
MAX3241E successfullꢅ drove all serial mice tested
and met their current and voltage requirements.
/MAX3246E
V
CC
0.1μF
5V/div
5V/div
5V/div
T1IN
T1OUT
R1OUT
V
CC
C1+
V+
V-
C3
C4
C1
C1-
C2+
MAX3222E
MAX3232E
MAX3237E
MAX3241E
MAX3246E
C2
C2-
V
CC
= 3.3V, C1–C4 = 0.1μF
T_ OUT
T_ IN
2μs/div
R_ IN
R_ OUT
Figure ±. MAX3241E Loopbac5 Test Result at 2ꢀ05bps
5kΩ
1000pF
GND
+5V
T_IN
0
Figure 7. Loopbac5 Test ꢁircuit
+5V
0
-5V
+5V
0
T_OUT
5kΩ + 250pF
V
= 3.3V
CC
C1–C4 = 0.1μF
5V/div
T1IN
R_OUT
400ns/div
5V/div
5V/div
T1OUT
Figure 10. MAX3237E Loopbac5 Test Result at 10005bps
(MꢄAUD = V
)
ꢁꢁ
R1OUT
V
= 3.3V
CC
C1–C4 = 0.1μF
2μs/div
2
Figure 8. MAX3241E Loopbac5 Test Result at 1205bps
±4 ______________________________________________________________________________________
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
7/MAX3241E
Figure 6a shows the transmitter output voltages under
increasing load current at +3.0V. Figure 6b shows a
tꢅpical mouse connection using the MAX3241E.
UCꢁꢂ Reliability
The UꢁSP represents a unique pac5aging form factor
that maꢅ not perform equallꢅ to a pac5aged product
through traditional mechanical reliabilitꢅ tests. UꢁSP
reliabilitꢅ is integrallꢅ lin5ed to the user’s assemblꢅ
methods, circuit board material, and usage environ-
ment. The user should closelꢅ review these areas when
considering use of a UꢁSP pac5age. Performance
through Operating Life Test and Moisture Resistance
remains uncompromised as the wafer-fabrication
process primarilꢅ determines it.
High Data Rates
The MAX3222E/MAX3232E/MAX3237E/MAX3241E/
MAX3246E maintain the RS-232 ±ꢀV minimum transmit-
ter output voltage even at high data rates. Figure 7
shows a transmitter loopbac5 test circuit. Figure 8
shows a loopbac5 test result at 1205bps, and Figure ±
shows the same test at 2ꢀ05bps. For Figure 8, all trans-
mitters were driven simultaneouslꢅ at 1205bps into RS-
232 loads in parallel with 1000pF. For Figure ±, a single
transmitter was driven at 2ꢀ05bps, and all transmitters
were loaded with an RS-232 receiver in parallel with
1000pF.
Mechanical stress performance is a greater considera-
tion for a UꢁSP pac5age. UꢁSPs are attached through
direct solder contact to the user’s Pꢁ board, foregoing
the inherent stress relief of a pac5aged product lead
frame. Solder joint contact integritꢅ must be consid-
ered. Table 4 shows the testing done to characterize
the UꢁSP reliabilitꢅ performance. In conclusion, the
UꢁSP is capable of performing reliablꢅ through envi-
ronmental stresses as indicated bꢅ the results in the
table. Additional usage data and recommendations are
detailed in Application Note 18±1: Wafer-Level
Pac5aging (WLP) and Its Applications.
The MAX3237E maintains the RS-232 ±ꢀ.0V minimum
transmitter output voltage at data rates up to 1Mbps.
Figure 10 shows a loopbac5 test result at 1Mbps with
MꢄAUD = V . For Figure 10, all transmitters were
ꢁꢁ
loaded with an RS-232 receiver in parallel with 2ꢀ0pF.
Interconnection with 3k and ꢀk Logic
The MAX3222E/MAX3232E/MAX3237E/MAX3241E/
MAX3246E can directlꢅ interface with various ꢀV logic
families, including AꢁT and ꢃꢁT ꢁMOS. See Table 3
for more information on possible combinations of inter-
connections.
Table 4. Reliability Test ꢀata
FAILURES PER
DURATION
TEST
CONDITIONS
SAMPLE SIZE
T
A
T
A
= -3ꢀ°ꢁ to +8ꢀ°ꢁ,
= -40°ꢁ to +100°ꢁ
1ꢀ0 cꢅcles,
±00 cꢅcles
0/10,
0/200
Temperature ꢁꢅcle
Operating Life
T
T
T
T
= +70°ꢁ
240 hours
240 hours
240 hours
24 hours
—
0/10
0/10
0/10
0/10
0/1ꢀ
0/ꢀ
A
A
A
A
Moisture Resistance
Low-Temperature Storage
Low-Temperature Operational
Solderabilitꢅ
= +20°ꢁ to +60°ꢁ, ±0ꢆ Rꢃ
= -20°ꢁ
/MAX3246E
= -10°ꢁ
8-hour steam age
ESD
1ꢀ5V, ꢃuman ꢄodꢅ Model
—
ꢃigh-Temperature Operating
Life
T = +1ꢀ0°ꢁ
J
168 hours
0/4ꢀ
______________________________________________________________________________________ ±1
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
__________________________________________________________ꢂin Configurations
TOP VIEW
+
+
+
+
N.C.
C1+
V+
1
2
N.C.
EN
C1+
V+
20
19
18
17
16
15
14
13
12
11
1
2
3
4
5
6
7
8
9
SHDN
1
2
3
4
5
6
7
8
C1+
V+
V
CC
18
17
16
15
14
13
12
11
EN
C1+
V+
1
2
SHDN
20
19
18
17
16
15
14
13
12
11
16
15
14
V
CC
V
GND
V
CC
CC
GND
3
GND
C1-
T1OUT
GND
3
T1OUT
R1IN
C1-
4
T1OUT
R1IN
C1-
T1OUT
R1IN
R1OUT
N.C.
MAX3232E
C1-
4
C2+
C2-
13 R1IN
12 R1OUT
11 T1IN
/MAX3246E
MAX3232E
MAX3222E
MAX3222E
C2+
C2-
5
C2+
C2-
C2+
C2-
5
R1OUT
T1IN
6
R1OUT
T1IN
6
V-
V-
7
V-
V-
10
9
7
T2OUT
R2IN
T2IN
T2OUT
T2IN
8
T2IN
T2OUT
R2IN
T2OUT
T1IN
R2OUT
8
R2OUT
N.C.
R2IN
N.C.
9
10 R2OUT
T2IN
R2IN
9
SO/DIP/SSOP/TSSOP
R2OUT
10
N.C.
10
SO/DIP
TSSOP
TSSOP/SSOP
+
+
TOP VIEW
28
28
27
26
25
24
23
22
1
2
1
2
3
4
5
6
7
8
9
C2+
C2-
C2+
GND
C1+
V+
C1+
27
26
V+
V
C2-
V-
3
CC
V
CC
+
R1IN
R2IN
1
2
3
4
5
6
7
8
24 GND
V-
25 C1-
4
R1IN
R2IN
R3IN
R4IN
R5IN
T1OUT
GND
C1-
23 C1-
T1IN
T1OUT
T2OUT
T3OUT
5
24
23
MAX3237E
MAX3241E
R3IN
22 EN
6
T2IN
EN
R4IN
21 SHDN
20 R1OUTB
19 R2OUTB
18 R1OUT
17 R2OUT
7
22 T3IN
21
SHDN
MAX3241E
R5IN
21 R1OUTB
R1IN
R2IN
8
R1OUT
T1OUT
T2OUT
T3OUT
20
19
20
19
R2OUTB
R1OUT
9
R2OUT
T4IN
10
11
12
13
14
T2OUT 10
T4OUT
R3IN
*EP
18 R3OUT T3OUT
18 R2OUT
17 R3OUT
16 R4OUT
11
12
13
14
T5IN
17
T5OUT
EN
T3IN
T2IN
T1IN
16 R1OUTB
15
15
MBAUD
R5OUT
SHDN
SSOP
SSOP/SO/TSSOP
TQFN
*CONNECT EP TO GND.
7/MAX3241E
±6 ______________________________________________________________________________________
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
7/MAX3241E
ꢂin Configurations (continued)
TOP VIEW
TOP VIEW
15
14
13
12
11
12
11
10
9
T2IN
N.C.
10
9
GND 16
17
T2IN
8
7
6
5
GND 13
V
CC
V
14
15
16
R2OUT
R2IN
CC
SHDN 18
EN 19
8
R2OUT
R2IN
MAX3222E
MAX3232E
V+
7
*EP
*EP
T2OUT
+
C1+
+
T2OUT
20
6
V+
1
2
3
4
5
1
2
3
4
TQFN
TQFN
TOP VIEW
(BUMPS ON BOTTOM)
B2: SHDN
C2: R1OUT
D2: T3IN
+
R4OUT R5OUT
R1IN
A4
R2IN
A5
E2: T2IN
B3: EN
A1
A2
B2
C2
D2
E2
F2
A3
A6 R3IN
R3OUT
E3: T1IN
BUMPS B4, B5, C3, C4,
C5, D3, D4, D5, E4, AND
E5 NOT POPULATED
R2OUT B1
B3
B6 R4IN
C6
C1
V-
R5IN
MAX3246E
C2-
C2+
V+
D6 T3OUT
D1
E1
F1
E3
E6
T2OUT
/MAX3246E
F3
F4
F5
F6 T1OUT
V
CC
C1+
C1-
GND
UCSP
*CONNECT EP TO GND.
______________________________________________________________________________________ ±7
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
__________________________________________________Typical Operating Circuits
+3.3V
+3.3V
17
16
C
C
BYPASS
BYPASS
V
V
CC
CC
3
7
2
4
5
6
2
6
1
3
4
5
C1+
C1+
V+
V+
C1
0.1μF
C1
0.1μF
C3*
C3*
0.1μF
0.1μF
C1-
C2+
C1-
C2+
MAX3222E
MAX3232E
V-
V-
C2
0.1μF
C2
0.1μF
/MAX3246E
C4
0.1μF
C4
0.1μF
C2-
C2-
12
T1OUT
T1IN
15
8
11
T1OUT
T1IN
14
7
TTL/CMOS
INPUTS
RS-232
OUTPUTS
TTL/CMOS
INPUTS
RS-232
OUTPUTS
T2IN
T2OUT
R1IN
11
T2IN
T2OUT
R1IN
10
14
9
13 R1OUT
10 R2OUT
13
8
12 R1OUT
TTL/CMOS
OUTPUTS
TTL/CMOS
OUTPUTS
RS-232
INPUTS
5kΩ
RS-232
INPUTS
5kΩ
R2IN
9
R2OUT
R2IN
5kΩ
5kΩ
EN
1
18
SHDN
GND
16
GND
15
*C3 CAN BE RETURNED TO EITHER V OR GROUND.
CC
NOTE: PIN NUMBERS REFER TO SO/DIP PACKAGES.
MAX3222E PINOUT REFERS TO SO/DIP PACKAGES.
MAX3232E PINOUT REFERS TO TSSOP/SSOP/SO/DIP PACKAGES
SEE TABLE 2 FOR CAPACITOR SELECTION.
7/MAX3241E
±8 ______________________________________________________________________________________
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
7/MAX3241E
_____________________________________Typical Operating Circuits (continued)
+3.3V
+3.3V
C
C
BYPASS
BYPASS
26
26
V
V
CC
CC
27
4
27
3
28
28
C1+
C1+
V+
V-
V+
C1
0.1μF
0.1μF
C3*
0.1μF
C3*
25
1
24
1
C1-
C2+
C1-
C2+
0.1μF
MAX3237E
MAX3241E
V-
C2
0.1μF
0.1μF
0.1μF
C4
3
2
0.1μF
C2-
C2-
T1IN
T1IN
T1OUT
T2OUT
T3OUT
5
6
7
T1OUT
9
24
14
13
T1
T2
T2IN
T3IN
T2IN
T2OUT 10
23
22
TTL/CMOS
INPUTS
RS-232
OUTPUTS
T3IN
12
21
11
RS-232
OUTPUTS
T3OUT
R1IN
LOGIC
INPUTS
T3
T4
T5
R1OUTB
T4IN
T5IN
T4OUT 10
19
17
R2OUTB
R1OUT
20
19
12
T5OUT
R1IN
4
5
R1OUTB
R1OUT
16
21
5kΩ
R2OUT
R3OUT
R4OUT
R2IN
18
17
16
8
9
R1
R2
R3
5kΩ
TTL/CMOS
OUTPUTS
5kΩ
R2IN
6
7
8
R3IN
RS-232
INPUTS
RS-232
INPUTS
R2OUT
R3OUT
20
18
LOGIC
5kΩ
OUTPUTS
5kΩ
R3IN
5kΩ
R4IN
11
5kΩ
R5OUT
EN
15
23
R5IN
15
14
5kΩ
MBAUD
SHDN
EN
13
22
SHDN
GND
2
GND
25
/MAX3246E
*C3 CAN BE RETURNED TO EITHER V OR GROUND.
CC
______________________________________________________________________________________ ±9
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
_____________________________________Typical Operating Circuits (continued)
+3.3V
C
BYPASS
F2
V
CC
F1
F3
C1+
V+
V-
C1
0.1μF
C3*
F4
E1
D1
C1-
C2+
0.1μF
/MAX3246E
MAX3246E
C1
C2
0.1μF
C4
0.1μF
C2-
T1IN
T1OUT F6
T2OUT E6
E3
E2 T2IN
RS-232
OUTPUTS
TTL/CMOS
INPUTS
T3IN
D2
C2
D6
A4
T3OUT
R1OUT
R1IN
5kΩ
R2OUT
R3OUT
R4OUT
R2IN A5
5kΩ
R3IN
5kΩ
R4IN
5kΩ
R5IN C6
5kΩ
B1
A1
A2
TTL/CMOS
OUTPUTS
A6
B6
RS-232
INPUTS
R5OUT
EN
A3
B3
B2
SHDN
GND
F5
*C3 CAN BE RETURNED TO EITHER V OR GROUND.
CC
7/MAX3241E
20 ______________________________________________________________________________________
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
7/MAX3241E
Ordering Information (continued)
ꢁelector Guide
PART
TEMP RANGE
PIN-PACKAGE
NO. OF
DRIVERS/
RECEIVERS
GUARANTEED
DATA RATE
(bps)
LOW-POWER
SHUTDOWN
PART
16 TQFN-EP**
(5mm x 5mm)
MAX3232ECTE+
0°C to +70°C
MAX3232ECUE+
MAX3232ECUP+
MAX3232EEAE+
MAX3232EEWE+
MAX3232EEPE+
0°C to +70°C
0°C to +70°C
16 TSSOP
20 TSSOP
16 SSOP
MAX3222E
MAX3232E
2/2
2/2
✔
2ꢀ05
2ꢀ05
—
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
MAX3237E
(Normal)
ꢀ/3
ꢀ/3
✔
✔
2ꢀ05
1M
16 Wide SO
16 Plastic DIP
MAX3237E
(Megaꢄaud)
16 TQFN-EP**
(5mm x 5mm)
MAX3232EETE+
-40°C to +85°C
MAX3241E
MAX3246E
3/ꢀ
3/ꢀ
✔
✔
2ꢀ05
2ꢀ05
MAX3232EEUE+
MAX3232EEUP+
MAX3237ECAI+
MAX3237EEAI+
MAX3241ECAI+
MAX3241ECWI+
MAX3241ECUI+
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
-40°C to +85°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
16 TSSOP
20 TSSOP
28 SSOP
ꢂac5age Information
28 SSOP
For the latest pac5age outline information and land patterns,
go to www.maxim-ic.com/pac5ages. Note that a “+”, “#”, or
“-” in the pac5age code indicates RoꢃS status onlꢅ. Pac5age
drawings maꢅ show a different suffix character, but the drawing
pertains to the pac5age regardless of RoꢃS status.
28 SSOP
28 Wide SO
28 TSSOP
32 TQFN-EP**
(7mm x 7mm)
ꢁACKAGE
TYꢁE
ꢁACKAGE
COꢀE
OUTLINE
NO.
LANꢀ
MAX3241ECTJ+
0°C to +70°C
ꢁATTERN NO.
MAX3241EEAI+
MAX3241EEWI+
MAX3241EEUI+
MAX3246ECBX-T+
MAX3246EEBX-T+
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
28 SSOP
20 TQFN
20 TSSOP
20 SSOP
18 Wide SO
18 PDIP
T20ꢀꢀ+ꢀ
ꢃ20+2
A20+1
W18+1
P18+ꢀ
20-0±40
2±-0066
2±-0016
2±-0042
2±-0043
2±-0016
2±-0042
2±-0043
2±-0±40
2±-0066
2±-0016
2±-0042
2±-0066
2±-0±44
90-00±0
90-0±±6
90-0094
90-0±8±
—
28 Wide SO
28 TSSOP
6 x 6 UCSP†
6 x 6 UCSP†
-40°C to +85°C
+Denotes a lead(Pb)-free/RoꢃS-compliant pac5age.
16 SSOP
16 Wide SO
16 PDIP
A16+2
W16+3
P16+1
90-0±06
90-0±07
—
†Requires solder temperature profile described in the Absolute
Maximum Ratings section. UꢁSP Reliabilitꢅ is integrallꢅ lin5ed
to the user’s assemblꢅ methods, circuit board material, and
environment. Refer to the UꢁSP Reliabilitꢅ Notice in the UꢁSP
Reliabilitꢅ section of this datasheet for more information.
16 TQFN
16 TSSOP
28 SSOP
28 Wide SO
28 TSSOP
32 TQFN
T16ꢀꢀ+2
U16+1
A28+1
W28+6
U28+2
T3277+2
90-0072
90-0±±7
90-0091
90-0±09
90-0±7±
90-0±21
**EP = Exposed pad.
Chip Information
PROꢁESS: ꢄIꢁMOS
/MAX3246E
Refer to
Application
Note ±89±
6x6 ꢃꢁSP
ꢄ36+3
2±-0082
______________________________________________________________________________________ 2±
1ꢀ5k EꢁD-ꢂrotected, Down to 10nA, 3.0k to ꢀ.ꢀk,
Up to 1Mbps, True Rꢁ-232 Transceivers
Revision History
REVISION REVISION
PAGES
CHANGED
DESCRIPTION
NUMBER
DATE
11
10/07
Corrected Package Information
22–28
Changed all parts to lead free in the Ordering Information, added automotive qualified
part to Ordering Information, corrected capacitor in Typical Operating Circuits
12
12/10
1, 19
/MAX3246E
Maxim cannot assume responsibilitꢅ for use of anꢅ circuitrꢅ other than circuitrꢅ entirelꢅ embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitrꢅ and specifications without notice at anꢅ time.
7/MAX3241E
22 ____________________Maxim Integrated ꢂroducts, 120 ꢁan Gabriel Drive, ꢁunnyvale, CA 94086 408-737-7600
© 2010 Maxim Integrated Products
Maxim is a registered trademar5 of Maxim Integrated Products, Inc.
相关型号:
MAX3222EEUP-T
Line Transceiver, 2 Func, 2 Driver, 2 Rcvr, BICMOS, PDSO20, 4.40 MM, MO-153AC, TSSOP-20
MAXIM
MAX3222EEUP/V+
±15kV ESD-Protected, Down to 10nA, 3.0V to 5.5V, Up to 1Mbps, True RS-232 Transceivers
MAXIM
MAX3222EEWN+
±15kV ESD-Protected, Down to 10nA, 3.0V to 5.5V, Up to 1Mbps, True RS-232 Transceivers
MAXIM
©2020 ICPDF网 联系我们和版权申明