MAX5153ACEE [MAXIM]
Low-Power, Dual, 13-Bit Voltage-Output DACs with Configurable Outputs; 低功耗,双通道, 13位电压输出DAC,带有可配置输出型号: | MAX5153ACEE |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | Low-Power, Dual, 13-Bit Voltage-Output DACs with Configurable Outputs |
文件: | 总20页 (文件大小:227K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-1304; Rev 0; 10/97
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
2/MAX153
_______________Ge n e ra l De s c rip t io n
____________________________Fe a t u re s
The MAX5152/MAX5153 low-power, serial, voltage-out-
put, dual 13-bit digital-to-analog converters (DACs)
consume only 500µA from a single +5V (MAX5152) or
+3V (MAX5153) supply. These devices feature Rail-to-
♦ 13-Bit Dual DAC with Configurable Output
Amplifier
♦ Single-Supply Operation: +5V (MAX5152)
+3V (MAX5153)
®
Rail output swing and are available in space-saving
♦ Rail-to-Rail Output Swing
16-pin QSOP and DIP packages. Access to the invert-
ing input allows for specific gain configurations, remote
sensing, and high output current capability, making
these devices ideally suited for industrial process con-
trols. These devices are also well suited for digitally
programmable (4–20mA) current loops.
♦ Low Quiescent Current:
500µA (normal operation)
2µA (shutdown mode)
♦ Power-On Reset Clears DAC Outputs to Zero
♦ SPI/QSPI and Microwire Compatible
♦ Space-Saving 16-Pin QSOP Package
The 3-wire s e ria l inte rfa c e is SPI™/QSPI™ a nd
Mic rowire ™ c omp a tib le . Ea c h DAC ha s a d oub le -
buffered input organized as an input register followed
by a DAC register, which allows the input and DAC reg-
isters to be updated independently or simultaneously.
Additional features include a programmable shutdown
(2µA), hardware-shutdown lockout, a separate voltage
reference for each DAC, power-on reset, and an active-
low clear input (CL) that resets all registers and DACs
to zero. The MAX5152/MAX5153 provide a programma-
ble logic output pin for added functionality, and a seri-
al-data output pin for daisy chaining.
♦ Pin-Compatible 12-Bit Versions:
MAX5156/MAX5157
______________Ord e rin g In fo rm a t io n
INL
(LSB)
PART
TEMP. RANGE
PIN-PACKAGE
MAX5152ACPE
MAX5152BCPE
MAX5152ACEE
MAX5152BCEE
MAX5152BC/D
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
16 Plastic DIP
16 Plastic DIP
16 QSOP
±1/2
±1
________________________Ap p lic a t io n s
Industrial Process Control Motion Control
±1/2
±1
16 QSOP
Dice*
±1
Digital Offset and Gain
Adjustment
Digitally Programmable
4–20mA Current Loops
Ordering Information continued at end of data sheet.
*Dice are tested at T = +25°C, DC parameters only.
A
Remote Industrial Controls Automatic Test Equipment
Pin Configuration appears at end of data sheet.
_________________________________________________________Fu n c t io n a l Dia g ra m
V
DD
DOUT CL
PDL
DGND
REFA
AGND
INPUT
REG A
DAC
REG A
OUTA
FBA
DAC A
DECODE
CONTROL
16-BIT
SHIFT
REGISTER
MAX5152
MAX5153
INPUT
REG B
DAC
REG B
OUTB
FBB
DAC B
LOGIC
OUTPUT
SR
CONTROL
REFB
CS
DIN SCLK UPO
Rail-to-Rail is a registered trademark of Nippon Motorola Ltd. SPI and QSPI are trademarks of Motorola, Inc.
Microwire is a trademark of National Semiconductor Corp.
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 408-737-7600 ext. 3468.
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
ABSOLUTE MAXIMUM RATINGS
V
to AGND............................................................-0.3V to +6V
to DGND ...........................................................-0.3V to +6V
Continuous Power Dissipation (T = +70°C)
A
DD
V
Plastic DIP (derate 10.5mW/°C above +70°C) .............593mW
QSOP (derate 8.30mW/°C above +70°C).....................667mW
CERDIP (derate 10.00mW/°C above +70°C)................800mW
Operating Temperature Ranges
DD
AGND to DGND..................................................................±0.3V
FBA, FBB to AGND.....................................-0.3V to (V + 0.3V)
REF_, OUT_ to AGND.................................-0.3V to (V + 0.3V)
DD
DD
Digital Inputs (SCLK, DIN, CS, CL, PDL)
to DGND................................................................-0.3V to +6V
Digital Outputs (DOUT, UPO) to DGND.....-0.3V to (V + 0.3V)
Maximum Current into Any Pin .........................................±20mA
MAX5152_C_E/MAX5153_C_E ...........................0°C to +70°C
MAX5152_E_E/MAX5153_E_E..........................-40°C to +85°C
MAX5152_MJE/MAX5153_MJE ......................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
DD
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—MAX5152
(V = +5V ±10%, V
= V
= 2.5V, R = 10kΩ, C = 100pF, T = T
to T , unless otherwise noted. Typical values are at
MAX
DD
REFA
REFB
L
L
A
MIN
T
A
= +25°C, output buffer connected in unity-gain configuration (Figure 9).)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
2/MAX153
STATIC PERFORMANCE
Resolution
N
13
Bits
MAX5152A
MAX5152B
±1/2
±1
Integral Nonlinearity
INL
(Note 1)
LSB
Differential Nonlinearity
Offset Error
DNL
Guaranteed monotonic
Code = 20
±1
LSB
mV
V
OS
±6
Offset Tempco
Gain Error
TCV
Normalized to 2.5V
3
-0.5
3
ppm/°C
LSB
OS
±6
Gain-Error Tempco
Normalized to 2.5V
ppm/°C
V
Power-Supply
DD
PSRR
REF
4.5V ≤ V ≤ 5.5V
20
200
µV/V
DD
Rejection Ratio
REFERENCE INPUT
V
-
DD
Reference Input Range
V
0
1.4
Reference Input Resistance
R
Minimum with code 1555 hex
Input code = 1FFF hex,
14
20
kΩ
REF
MULTIPLYING-MODE PERFORMANCE
Reference 3dB Bandwidth
600
-85
82
kHz
dB
V
REF
= 0.67Vp-p at 2.5V
DC
Input code = 0000 hex,
= (V - 1.4Vp-p) at 1kHz
Reference Feedthrough
V
REF
DD
Signal-to-Noise plus
SINAD
Input code = 1FFF hex,
= 1Vp-p at 2.5V , f = 25kHz
dB
V
REF
Distortion Ratio
DC
DIGITAL INPUTS
Input High Voltage
Input Low Voltage
Input Hysteresis
V
3.0
V
V
CL, PDL, CS, DIN, SCLK
CL, PDL, CS, DIN, SCLK
IH
V
IL
0.8
±1
V
HYS
200
0.001
8
mV
µA
pF
Input Leakage Current
Input Capacitance
I
IN
V
= 0V to V
IN DD
C
IN
2
_______________________________________________________________________________________
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
2/MAX153
ELECTRICAL CHARACTERISTICS—MAX5152 (continued)
(V = +5V ±10%, V
= V
= 2.5V, R = 10kΩ, C = 100pF, T = T
to T , unless otherwise noted. Typical values are at
MAX
DD
REFA
REFB
L
L
A
MIN
T
A
= +25°C, output buffer connected in unity-gain configuration (Figure 9).)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DIGITAL OUTPUTS (DOUT, UPO)
V
DD
0.5
-
Output High Voltage
V
I
= 2mA
V
V
OH
SOURCE
Output Low Voltage
V
OL
I
= 2mA
0.13
0.40
SINK
DYNAMIC PERFORMANCE
Voltage Output Slew Rate
Output Settling Time
SR
0.75
20
V/µs
µs
To 1/2LSB of full-scale, V
= 2.5V
STEP
Output Voltage Swing
Current into FBA or FBB
Rail-to-rail (Note 2)
0 to V
V
DD
I
FB
_
0
±0.1
µA
Time Required to Exit
Shutdown
25
µs
Digital Feedthrough
Digital Crosstalk
5
5
nV-s
nV-s
CS = V , f
= 100kHz, V
= 5Vp-p
DD DIN
SCLK
POWER SUPPLIES
Positive Supply Voltage
Power-Supply Current
V
4.5
5.5
V
DD
I
DD
(Note 3)
(Note 3)
0.5
2
0.65
mA
Power-Supply Current in
Shutdown
I
10
±1
µA
µA
DD(SHDN)
Reference Current in
Shutdown
TIMING CHARACTERISTICS
SCLK Clock Period
t
(Note 4)
100
40
ns
ns
ns
CP
SCLK Pulse Width High
SCLK Pulse Width Low
t
CH
t
40
CL
CS Fall to SCLK Rise Setup
Time
t
40
0
ns
ns
CSS
SCLK Rise to CS Rise Hold
Time
t
CHS
DIN Setup Time
DIN Hold Time
t
40
0
ns
ns
DS
t
DH
SCLK Rise to DOUT Valid
Propagation Delay
t
C
C
= 200pF
= 200pF
80
80
ns
ns
DO1
DO2
LOAD
LOAD
SCLK Fall to DOUT Valid
Propagation Delay
t
t
10
40
ns
ns
ns
SCLK Rise to CS Fall Delay
CS Rise to SCLK Rise Hold
CS Pulse Width High
CS0
t
CS1
t
100
CSW
Note 1: Accuracy is specified from code 20 to code 8191.
Note 2: Accuracy is better than 1LSB for V greater than 6mV and less than V - 50mV. Guaranteed by PSRR test at the end
OUT
DD
points.
Note 3: Digital inputs are set to either V or DGND, code = 0000 hex, R = ∞.
DD
L
Note 4: SCLK minimum clock period includes rise and fall times.
_______________________________________________________________________________________
3
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
ELECTRICAL CHARACTERISTICS—MAX5153
(V = +2.7V to +3.6V, V
= V
= 1.25V, R = 10kΩ, C = 100pF, T = T
to T , unless otherwise noted. Typical values
MAX
DD
REFA
REFB
L
L
A
MIN
are at T = +25°C, output buffer connected in unity-gain configuration (Figure 9).)
A
PARAMETER
STATIC PERFORMANCE
Resolution
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
N
13
Bits
MAX5153A
MAX5153B
±1
±2
±1
±6
Integral Nonlinearity
INL
(Note 5)
LSB
Differential Nonlinearity
Offset Error
DNL
Guaranteed monotonic
Code = 40
LSB
mV
V
OS
Offset Tempco
Gain Error
TCV
Normalized to 1.25V
6
-0.5
6
ppm/°C
LSB
OS
±8
Gain-Error Tempco
Normalized to 1.25V
ppm/°C
V
Power-Supply
DD
PSRR
REF
2.7V ≤ V ≤ 3.6V
20
320
µV/V
DD
Rejection Ratio
2/MAX153
REFERENCE INPUT (V
)
REF
V
-
DD
Reference Input Range
V
0
1.4
Reference Input Resistance
R
Minimum with code 1555 hex
Input code = 1FFF hex,
14
kΩ
REF
MULTIPLYING-MODE PERFORMANCE
Reference 3dB Bandwidth
600
-92
73
kHz
dB
V
= 0.67Vp-p at 1.25V
DC
REF(AC)
Input code = 0000 hex,
= (V - 1.4V) at 1kHz
Reference Feedthrough
V
REF
DD
Signal-to-Noise plus
SINAD
Input code = 1FFF hex,
= 1Vp-p at 1.25V , f = 15kHz
dB
V
REF
Distortion Ratio
DC
DIGITAL INPUTS
Input High Voltage
Input Low Voltage
Input Hysteresis
V
2.2
V
V
CL, PDL, CS, DIN, SCLK
CL, PDL, CS, DIN, SCLK
IH
V
IL
0.8
V
HYS
200
0
mV
µA
pF
Input Leakage Current
Input Capacitance
I
IN
V
= 0V to V
DD
±0.1
IN
C
8
IN
DIGITAL OUTPUTS (DOUT, UPO)
Output High Voltage
Output Low Voltage
V
I
= 2mA
V - 0.5
DD
V
V
OH
SOURCE
V
OL
I
= 2mA
0.13
0.4
SINK
4
_______________________________________________________________________________________
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
2/MAX153
ELECTRICAL CHARACTERISTICS—MAX5153 (continued)
(V = +2.7V to +3.6V, V
= V
= 1.25V, R = 10kΩ, C = 100pF, T = T
to T
, unless otherwise noted. Typical values
MAX
DD
REFA
REFB
L
L
A
MIN
are at T = +25°C, output buffer connected in unity-gain configuration (Figure 9).)
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DYNAMIC PERFORMANCE
Voltage Output Slew Rate
Output Settling Time
SR
0.75
25
V/µs
µs
To 1/2LSB of full-scale, V
= 1.25V
STEP
Output Voltage Swing
Current into FBA or FBB
Rail-to-rail (Note 6)
0 to V
V
DD
I
0
±0.1
µA
FB_
Time Required to Exit
Shutdown
25
µs
Digital Feedthrough
Digital Crosstalk
5
5
nV-s
nV-s
CS = V , f
= 100kHz, V
= 3Vp-p
DD DIN
SCLK
POWER SUPPLIES
Positive Supply Voltage
Power-Supply Current
V
2.7
3.6
0.6
V
DD
I
DD
(Note 7)
(Note 7)
0.5
1
mA
Power-Supply Current in
Shutdown
I
8
µA
µA
DD(SHDN)
Reference Current in
Shutdown
±1
TIMING CHARACTERISTICS
SCLK Clock Period
t
(Note 4)
100
40
ns
ns
ns
CP
SCLK Pulse Width High
SCLK Pulse Width Low
t
CH
t
40
CL
CS Fall to SCLK Rise Setup
Time
t
40
0
ns
ns
CSS
SCLK Rise to CS Rise Hold
Time
t
CHS
DIN Setup Time
DIN Hold Time
t
50
0
ns
ns
DS
t
DH
SCLK Rise to DOUT Valid
Propagation Delay
t
t
C
C
= 200pF
= 200pF
120
120
ns
ns
DO1
DO2
LOAD
LOAD
SCLK Fall to DOUT Valid
Propagation Delay
t
10
40
ns
ns
ns
SCLK Rise to CS Fall Delay
CS Rise to SCLK Rise Hold
CS Pulse Width High
CS0
CS1
t
t
100
CSW
Note 4: SCLK minimum clock period includes rise and fall times.
Note 5: Accuracy is specified from code 40 to code 8191.
Note 6: Accuracy is better than 1LSB for V
greater than 6mV and less than V - 100mV. Guaranteed by PSRR test at the end
DD
OUT
points.
Note 7: Digital inputs are set to either V or DGND, code = 0000 hex, R = ∞.
DD
L
_______________________________________________________________________________________
5
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
__________________________________________Typ ic a l Op e ra t in g Ch a ra c t e ris t ic s
(V = +5V, R = 10kΩ, C = 100pF, FB_ tied to OUT_, T = +25°C, unless otherwise noted.)
DD
L
L
A
MAX5152
REFERENCE VOLTAGE INPUT
FREQUENCY RESPONSE
SUPPLY CURRENT
vs. TEMPERATURE
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
0
0.60
0.55
0.50
0.45
0.40
-30
-40
-50
-60
-70
-80
-90
V
= 1Vp-p AT 2.5V
DC
REF
-2
-4
R =
L
∞
CODE = 1FFF (HEX)
CODE = 1FFF (HEX)
-6
-8
-10
-12
-14
-16
-18
-20
CODE = 0000 (HEX)
V
= 0.67Vp-p AT 2.5V
DC
REF
CODE = 1FFF (HEX)
2/MAX153
0
600 1200
1800
2400
3000
-60
-20
20
60
100
140
0
10
100
FREQUENCY (kHz)
TEMPERATURE (°C)
FREQUENCY (kHz)
POWER-DOWN CURRENT
vs. TEMPERATURE
REFERENCE FEEDTHROUGH AT 1kHz
FULL-SCALE ERROR vs. LOAD
-50
-60
3.0
2.5
2.0
1.5
1.0
0.5
0
0
V
= 3.6Vp-p AT 1.88V
DC
REF
V
REF
= 2.5V
CODE = 0000 (HEX)
-70
-0.2
-0.4
-0.6
-0.8
-80
-90
-100
-110
-120
-130
-140
-150
-1.0
-55 -35 -15
5
25 45 65 85 105 125
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
FREQUENCY (kHz)
0.1
1
10
100
1000
TEMPERATURE (°C)
LOAD (kΩ)
OUTPUT FFT PLOT
DYNAMIC-RESPONSE FALL TIME
MAX5152 TOC09
DYNAMIC-RESPONSE RISE TIME
MAX5152 TOC08
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
CS
5V/div
AC COUPLED
CS
5V/div
AC COUPLED
V
REF
= 3.6Vp-p AT 1.8V
DC
f = 1kHz
CODE = 1FFF (HEX)
NOTE: RELATIVE TO FULL SCALE
OUT_
500mV/div
OUT_
500mV/div
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
FREQUENCY (kHz)
2µs/div
2µs/div
6
_______________________________________________________________________________________
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
2/MAX153
____________________________Typ ic a l Op e ra t in g Ch a ra c t e ris t ic s (c o n t in u e d )
(V = +3V, R = 10kΩ, C = 100pF, FB_ tied to OUT_, T = +25°C, unless otherwise noted.)
DD
L
L
A
MAX5153
REFERENCE VOLTAGE INPUT
FREQUENCY RESPONSE
TOTAL HARMONIC DISTORTION
PLUS NOISE vs. FREQUENCY
SUPPLY CURRENT
vs. TEMPERATURE
0
-30
-40
-50
-60
-70
-80
-90
0.60
0.55
0.50
0.45
0.40
V
= 1Vp-p AT 1V
DC
REF
-2
-4
R = ∞
L
CODE = 1FFF (HEX)
-6
CODE = 1FFF (HEX)
CODE = 0000 (HEX)
-8
-10
-12
-14
-16
-18
-20
V
= 0.67Vp-p AT 1.25V
DC
REF
CODE = 1FFF (HEX)
0
500 1000
1500
2000
2500
0
10
100
-60
-20
20
60
100
140
FREQUENCY (kHz)
FREQUENCY (kHz)
TEMPERATURE (°C)
POWER-DOWN CURRENT
vs. TEMPERATURE
REFERENCE FEEDTHROUGH AT 1kHz
FULL-SCALE ERROR vs. LOAD
-50
-60
0
-0.2
-0.4
-0.6
-0.8
-1.0
-1.2
3.0
2.5
2.0
1.5
1.0
0.5
0
V
REF
= 1.6Vp-p AT 0.88V
DC
CODE = 0000 (HEX)
-70
-80
-90
-100
-110
-120
-130
-140
-150
V
= 1.25V
1
REF
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
FREQUENCY (kHz)
-55 -35 -15
5
25 45 65 85 105 125
0.1
10
100
1000
TEMPERATURE (°C)
LOAD (kΩ)
OUTPUT FFT PLOT
DYNAMIC-RESPONSE FALL TIME
DYNAMIC-RESPONSE RISE TIME
MAX5152 TOC18
MAX5152 TOC17
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
V
REF
= 1.6Vp-p AT 0.88V
DC
f = 1kHz
CODE = 1FFF (HEX)
NOTE: RELATIVE TO FULL SCALE
CS
2V/div
CS
2V/div
OUT_
500mV/div
OUT_
500mV/div
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
FREQUENCY (kHz)
2µs/div
2µs/div
_______________________________________________________________________________________
7
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
____________________________Typ ic a l Op e ra t in g Ch a ra c t e ris t ic s (c o n t in u e d )
(V = +5V (MAX5152), V = +3V (MAX5153), R = 10kΩ, C = 100pF, FB_ tied to OUT_, T = T
to T , unless otherwise
MAX
DD
DD
L
L
A
MIN
noted.)
MAX5152/MAX5153
MAX5153
MAX5152
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
0.55
0.50
0.45
0.40
0.35
0.30
0.60
0.55
0.50
0.45
0.40
0.35
0.30
CODE = 1FFF (HEX)
CODE = 1FFF (HEX)
CODE = 0000 (HEX)
CODE = 0000 (HEX)
2/MAX153
R = ∞
L
R = ∞
L
2.7
3.0
3.3
3.6
4.50
4.75
5.00
5.25
5.50
SUPPLY VOLTAGE (V)
SUPPLY VOLTAGE (V)
MAX5152
MAJOR-CARRY TRANSITION
MAX5152 TOC20
CS
2V/div
OUT_
10mV/div
AC COUPLED
2µs/div
MAX5152
ANALOG CROSSTALK
MAX5152
DIGITAL FEEDTHROUGH
MAX5152 TOC21
MAX5152 TOC22
SCLK
5V/div
OUTA
1V/div
OUTA
500µV/div
AC COUPLED
OUTB
200µV/div
AC COUPLED
200µs/div
1µs/div
8
_______________________________________________________________________________________
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
2/MAX153
______________________________________________________________P in De s c rip t io n
PIN
NAME
FUNCTION
1
2
3
4
5
AGND
OUTA
FBA
Analog Ground
DAC A Output Voltage
DAC A Output Amplifier Feedback Input. Inverting input of the output amplifier.
Reference for DAC A
REFA
CL
Active-Low Clear Input. Resets all registers to zero. DAC outputs go to 0V.
6
Chip-Select Input
CS
DIN
7
Serial Data Input
8
SCLK
DGND
DOUT
UPO
Serial Clock Input
9
Digital Ground
10
11
12
13
14
15
16
Serial Data Output
User-Programmable Output
PDL
Power-Down Lockout. The device cannot be powered down when PDL is low.
Reference Input for DAC B
REFB
FBB
DAC B Output Amplifier Feedback Input. Inverting input of the output amplifier.
DAC B Output Voltage
OUTB
V
DD
Positive Power Supply
_______________De t a ile d De s c rip t io n
FB_
The MAX5152/MAX5153 dual, 13-bit, voltage-output
DACs are easily configured with a 3-wire serial inter-
face. These devices include a 16-bit data-in/data-out
shift register, and each DAC has a double-buffered
input comprised of an input register and a DAC register
(see Functional Diagram). Both DACs use an inverted
R-2R ladder network that produces a weighted voltage
proportional to the input voltage value. Each DAC has
its own reference input to facilitate independent full-
scale values. Figure 1 depicts a simplified circuit dia-
gram of one of the two DACs.
OUT_
R
R
R
2R
D0
2R
D10
2R
D11
2R
D12
2R
REF_
AGND
Re fe re n c e In p u t s
The reference inputs accept both AC and DC values
SHOWN FOR ALL 1s ON DAC
with a voltage range extending from 0V to (V - 1.4V).
DD
Determine the output voltage using the following equa-
tion:
Figure 1. Simplified DAC Circuit Diagram
V
= V
x NB / 8192
Ou t p u t Am p lifie r
The output amplifier’s inverting input is available to the
user, allowing force and sense capability for remote
sensing and specific gain configurations. The inverting
input can be connected to the output to provide a unity-
gain buffered output. The output amplifiers have a typi-
cal slew rate of 0.75V/µs and settle to 1/2LSB within
25µs, with a load of 10kΩ in parallel to 100pF. Loads
less than 2kΩ degrade performance.
OUT
REF
where NB is the numeric value of the DAC’s binary input
code (0 to 8191) and V is the reference voltage.
REF
The reference input impedance ranges from 14kΩ (1555
hex) to several giga ohms (with an input code of 0000
hex). This reference input capacitance is code depen-
dent and typically ranges from 15pF with an input code
of all zeros to 50pF with an input code of all ones.
_______________________________________________________________________________________
9
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
Table 1. Serial-Interface Programming Commands
16-BIT SERIAL WORD
FUNCTION
D 1 2 . . . . . . . . . . . . . . . . D 0
A0 C1
C0
MSB
LSB
0
1
0
1
0
0
1
1
1
1
0
0
13 bits of DAC data
Load input register A; DAC register is unchanged.
Load input register B; DAC register is unchanged.
Load input register A; all DAC registers are updated.
Load input register B; all DAC registers are updated.
13 bits of DAC data
13 bits of DAC data
13 bits of DAC data
Load all DAC registers from the shift register (start up both DACs with new
data).
0
1
1
13 bits of DAC data
Update both DAC registers from their respective input registers
(start up both DACs with data previously stored in the input registers).
1
1
0
0
1
0
0
1
0
xxxxxxxxxxxxx
xxxxxxxxxxxxx
Shut down both DACs if PDL = 1.
2/MAX153
Update DAC register A from input register A (start up DAC A with data previ-
ously stored in input register A).
0 0 1 x xxxxxxxxx
Update DAC register B from input register B (start up DAC B with data previ-
ously stored in input register B).
0
0
0
1 0 1 x xxxxxxxxx
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1 1 0 x xxxxxxxxx
1 1 1 x xxxxxxxxx
0 1 0 x xxxxxxxxx
0 1 1 x xxxxxxxxx
1 0 0 1 xxxxxxxxx
1 0 0 0 xxxxxxxxx
0 0 0 x xxxxxxxxx
Shut down DAC A when PDL = 1.
Shut down DAC B when PDL = 1.
UPO goes low (default).
UPO goes high.
Mode 1, DOUT clocked out on SCLK’s rising edge.
Mode 0, DOUT clocked out on SCLK’s falling edge (default).
No operation (NOP).
“x” = don’t care
Note: When A0, C1, and C0 = “0”, D12, D11, D10, and D9 become control bits.
P o w e r-Do w n Mo d e
S e ria l In t e rfa c e
The MAX5152/MAX5153 feature a software-program-
mable shutdown mode that reduces the typical supply
current to 2µA. The two DACs can be shut down inde-
pendently or simultaneously by using the appropriate
programming word. For instance, enter shutdown mode
(for both DACs) by writing an input control word of
111XXXXXXXXXXXXX (Table 1). In shutdown mode, the
reference inputs and amplifier outputs become high
impedance, and the serial interface remains active.
Da ta in the inp ut re g is te rs is s a ve d , a llowing the
MAX5152/MAX5153 to recall the output state prior to
entering shutdown when returning to normal mode. Exit
shutdown by recalling the previous condition or by
updating the DAC with new information. When returning
to normal operation (exiting shutdown), wait 20µs for
output stabilization.
The MAX5152/MAX5153 3-wire serial interface is com-
patible with both Microwire (Figure 2) and SPI/QSPI
(Figure 3) serial-interface standards. The 16-bit serial
input word consists of an address bit, two control bits,
and 13 bits of data (MSB to LSB) as shown in Figure 4.
The address and control bits determines the response
of the MAX5152/MAX5153, as outlined in Table 1.
The MAX5152/MAX5153’s digital inputs are double
buffered, which allows any of the following: loading the
input register(s) without updating the DAC register(s),
updating the DAC register(s) from the input register(s),
or updating the input and DAC registers concurrently.
The address and control bits allow for the DACs to act
independently.
10 ______________________________________________________________________________________
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
2/MAX153
Se nd the 16-b it d a ta a s two 8-b it p a c ke ts (SPI,
Microwire) or one 16-bit word (QSPI), with CS low dur-
ing this period. The address and control bits determine
which register will be updated, as well as the state of
the re g is te rs whe n e xiting s hutd own. The 3-b it
address/control determines:
SCLK
SK
• registers to be updated
MICROWIRE
PORT
MAX5152
MAX5153
• clock edge on which data is clocked out via the seri-
DIN
CS
SO
I/O
al data output (DOUT)
• state of the user-programmable logic output
• configuration of the device after shutdown
The general timing diagram in Figure 5 illustrates how
data is acquired. Driving CS low enables the device to
receive data. Otherwise, the interface control circuitry is
disabled. With CS low, data at DIN is clocked into the
register on the rising edge of SCLK. As CS goes high,
data is latched into the input and/or DAC registers
depending on the address and control bits. The maxi-
mum clock frequency guaranteed for proper operation
is 10MHz. Figure 6 depicts a more detailed timing dia-
gram of the serial interface.
Figure 2. Connections for Microwire
V
CC
Serial Data Output (DOUT)
DOUT is the internal shift register’s output. It allows for
d a is y-c ha ining a nd d a ta re a d b a c k. The MAX5152/
MAX5153 c a n b e p rog ra mme d to s hift d a ta out of
DOUT on SCLK’s falling edge (Mode 0) or rising edge
(Mode 1). Mode 0 provides a lag of 16 clock cycles,
whic h ma inta ins c omp a tib ility with SPI/QSPI a nd
Microwire interfaces. In Mode 1, the output data lags
15.5 clock cycles. On power-up, the device defaults to
Mode 0.
SS
DIN
MOSI
SCK
SPI/QSPI
PORT
MAX5152
SCLK
MAX5153
CS
I/O
User-Programmable Logic Output (UPO)
UPO allows an external device to be controlled through
the MAX5152/MAX5153 serial interface (Table 1), there-
by reducing the number of microcontroller I/O pins
required. On power-up, UPO is low.
CPOL = 0, CPHA = 0
Figure 3. Connections for SPI/QSPI
Power-Down Lockout Input (PDL)
PDL disables software shutdown when low. When in
shutdown, transitioning PDL from high to low wakes up
the part with the output set to the state prior to shut-
down. PDL can also be used to asynchronously wake
up the device.
MSB ..................................................................................LSB
16 Bits of Serial Data
Address Bits
A0
Control Bits
C1, C0
MSB.......Data Bits.........LSB
D12.................................D0
13 Data Bits
Daisy Chaining Devices
Any numb e r of MAX5152/MAX5153s c a n b e d a is y
chained by connecting the DOUT pin of one device to
the DIN pin of the following device in the chain (Figure
7).
1 Address/2 Control Bits
Figure 4. Serial-Data Format
______________________________________________________________________________________ 11
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
CS
COMMAND
EXECUTED
SCLK
1
8
9
16
D6 D5 D4 D3 D2 D1 D0
C1
DIN
A0
C0 D12 D11 D10 D9 D8
D7
Figure 5. Serial-Interface Timing Diagram
t
CSW
CS
t
CP
t
CSH
t
t
CH
CSS
t
t
CL
CSO
t
CS1
2/MAX153
SCLK
t
DS
t
DH
DIN
Figure 6. Detailed Serial-Interface Timing Diagram
SCLK
SCLK
SCLK
MAX5152
MAX5153
MAX5152
MAX5153
MAX5152
MAX5153
DIN
CS
DOUT
DIN
CS
DOUT
DIN
CS
DOUT
TO OTHER
SERIAL DEVICES
Figure 7. Daisy Chaining MAX5152/MAX5153s
Since the MAX5152/MAX5153’s DOUT has an internal
active pull-up, the DOUT sink/source capability deter-
mines the time required to discharge/charge a capaci-
Figure 8 shows an alternative method of connecting
several MAX5152/MAX5153s. In this configuration, the
data bus is common to all devices; data is not shifted
through a daisy-chain. More I/O lines are required in
this configuration because a dedicated chip-select
input (CS) is required for each IC.
tive loa d . Re fe r to the d ig ita l outp ut V
a nd V
OH
OL
specifications in the Electrical Characteristics.
12 ______________________________________________________________________________________
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
2/MAX153
DIN
SCLK
CS1
CS2
TO OTHER
SERIAL DEVICES
CS3
CS
CS
CS
MAX5152
MAX5153
SCLK
MAX5152
MAX5153
SCLK
MAX5152
MAX5153
SCLK
DIN
DIN
DIN
Figure 8. Multiple MAX5152/MAX5153s Sharing a Common DIN Line
Table 2. Unipolar Code Table (Gain = +1)
+5V/+3V
REF_
DAC CONTENTS
ANALOG OUTPUT
MSB
LSB
V
DD
8191
8192
1 1 1 1 1
1 1 1 1
0 0 0 0
0 0 0 0
1 1 1 1
1 1 1 1
+V
REF
MAX5152
MAX5153
FB_
4097
8192
1 0 0 0 0
1 0 0 0 0
0 1 1 1 1
0 0 0 1
0 0 0 0
1 1 1 1
+V
REF
DAC
OUT_
V
4096
8192
REF
+V
=
REF
2
DGND
AGND
4095
+V
REF
8192
1
Figure 9. Unipolar Output Circuit
0 0 0 0 0
0 0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 1
0 0 0 0
+V
REF
8192
0V
Bip o la r Ou t p u t
__________Ap p lic a t io n s In fo rm a t io n
The MAX5152/MAX5153 can be configured for a bipo-
lar output, as shown in Figure 11. The output voltage is
given by the equation:
Un ip o la r Ou t p u t
Figure 9 depicts the MAX5152/MAX5153 configured for
unity-gain, unipolar operation. Table 2 lists the unipolar
output codes. To increase dynamic range, specific
gain configurations can be used as shown in Figure 10.
V
OUT
= V
[((2 x NB) / 8192) - 1]
REF
where NB represents the numeric value of the DAC’s
binary input code. Table 3 shows digital codes and the
corresponding output voltage for Figure 11’s circuit.
______________________________________________________________________________________ 13
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
REF_
+5V/+3V
+5V/+3V
REF_
10k
10k
V
DD
R2
R1
V
DD
MAX5152
MAX5153
FB_
V+
FB_
MAX5152
MAX5153
V
OUT
DAC
V
OUT
OUT_
DAC _
OUT_
DGND
N
AGND
V-
DGND
AGND
=
+ R1
V
REF_
V
OUT
1
(
) (
)(
)
R2 8192
Figure 10. Configurable Output Gain
Figure 11. Bipolar Output Circuit
2/MAX153
Table 3. Bipolar Code Table
+5V/
+3V
DAC CONTENTS
+5V/+3V
ANALOG OUTPUT
26k
AC
MSB
LSB
MAX495
REF_
REFERENCE
INPUT
4095
1 1 1 1 1
1 1 1 1
1 1 1 1
+V
REF
4096
10k
1
500mVp-p
1 0 0 0 0
1 0 0 0 0
0 1 1 1 1
0 0 0 0
0 0 0 0
1 1 1 1
0 0 0 1
0 0 0 0
1 1 1 1
+V
V
DD
REF
4096
FB_
0V
1
-V
REF
4096
DAC_
OUT_
4095
4096
0 0 0 0 0
0 0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 1
0 0 0 0
-V
REF
MAX5152
MAX5153
DGND
AGND
4096
4096
-V
= - V
REF
REF
Figure 12. AC Reference Input Circuit
Us in g a n AC Re fe re n c e
Ha rm o n ic Dis t o rt io n a n d No is e
The total harmonic distortion plus noise (THD+N) is typ-
ically less than -80dB at full scale with a 1Vp-p input
swing at 5kHz. The typical -3dB frequency is 600kHz
for both devices, as shown in the Typical Operating
Characteristics.
In applications where the reference has an AC signal
component, the MAX5152/MAX5153 have multiplying
capabilities within the reference input voltage range
specifications. Figure 12 shows a technique for apply-
ing a sinusoidal input to the reference input to REF_,
where the AC signal is offset before being applied to
the reference input.
14 ______________________________________________________________________________________
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
2/MAX153
Dig it a l Ca lib ra t io n a n d
Th re s h o ld S e le c t io n
Figure 13 shows the MAX5152/MAX5153 in a digital
V+
calibration application. With a bright value applied to
REF_
+5V/+3V
PHOTODIODE
the photodiode (on), the DAC is digitally ramped up
until it trips the comparator. The microprocessor stores
this high calibration value. Repeat the process with a
dim light (off) to obtain the dark current calibration. The
microprocessor then programs the DAC to set an out-
put voltage that is the midpoint of the two calibration
values. Applications include tachometers, motion sens-
ing, automatic readers, and liquid clarity analysis.
V
DD
MAX5152
MAX5153
V+
FB_
V
OUT
OUT_
Dig it a l Co n t ro l o f Ga in a n d Offs e t
The two DACs can be used to control the offset and
gain for curve-fitting nonlinear functions, such as trans-
ducer linearization or analog compression/expansion
applications. The input signal is used as the reference
for the gain-adjust DAC, whose output is summed with
the output from the offset-adjust DAC. The relative
weight of each DAC output is adjusted by R1, R2, R3,
and R4 (Figure 14).
DAC _
µP
DIN
V-
R
DGND
AGND
Figure 13. Digital Calibration
+5V/+3V
V
DD
MAX5152
MAX5153
FBA
V
IN
R1
REFA
DACA
CS
OUT_A
OUT_B
R2
DIN
SCLK
CL
V
OUT
R3
DACB
REFB
R4
V
REF
FBB
V
OUT
= GAIN
–
OFFSET
[ ] [
]
NA
R2
R4
1+
(
)( )( ) ( NB )(R4 )
=
V
V
REF
DGND
AGND
IN
[
R3 ] [
]
8192 R1+R2
8192 R3
NA IS THE NUMERIC VALUE OF THE INPUT CODE FOR DACA.
NB IS THE NUMERIC VALUE OF THE INPUT CODE FOR DACB.
Figure 14. Digital Control of Gain and Offset
______________________________________________________________________________________ 15
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
Dig it a l P ro g ra m m a b le Cu rre n t S o u rc e
Figure 15 depicts a digitally programmable, unidirec-
tional current source that can be used in industrial con-
trol applications. The output current is:
REF_
+5V/+3V
I
= (V
/ R) (NB / 8192)
OUT
REF
V
L
where NB is the DAC code and R is the sense resistor.
V
DD
I
OUT
P o w e r-S u p p ly Co n s id e ra t io n s
On power-up, the input and DAC registers clear (reset
DAC_
OUT_
FB_
2N3904
to zero code). For rated performance, V
should be
REF_
at least 1.4V below V . Bypass the power supply with
DD
MAX5152
MAX5153
a 4.7µF capacitor in parallel with a 0.1µF capacitor to
GND. Minimize lead lengths to reduce lead inductance.
R
Gro u n d in g a n d La yo u t Co n s id e ra t io n s
Digital and AC transient signals on AGND can create
noise at the output. Connect AGND to the highest quali-
ty ground available. Use proper grounding techniques,
s uc h a s a multila ye r b oa rd with a n unb roke n, low-
inductance ground plane. Carefully lay out the traces
between channels to reduce AC cross-coupling and
crosstalk. Wire-wrapped boards and sockets are not
recommended. If noise becomes an issue, shielding
may be required.
DGND
AGND
2/MAX153
Figure 15. Digitally Programmable Current Source
16 ______________________________________________________________________________________
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
2/MAX153
_Ord e rin g In fo rm a t io n (c o n t in u e d )
__________________P in Co n fig u ra t io n
INL
(LSB)
TOP VIEW
PART
TEMP. RANGE
PIN-PACKAGE
AGND
OUTA
FBA
REFA
CL
1
2
3
4
5
6
7
8
16 V
DD
MAX5152AEPE -40°C to +85°C
MAX5152BEPE -40°C to +85°C
MAX5152AEEE -40°C to +85°C
MAX5152BEEE -40°C to +85°C
16 Plastic DIP
16 Plastic DIP
16 QSOP
±1/2
±1
±1/2
±1
±1
±1
±2
±1
±2
±2
±1
±2
±1
±2
±2
15 OUTB
14 FBB
13 REFB
12 PDL
11 UPO
10 DOUT
MAX5152
MAX5153
16 QSOP
MAX5152BMJE -55°C to +125°C 16 CERDIP**
MAX5153ACPE
MAX5153BCPE
MAX5153ACEE
MAX5153BCEE
MAX5153BC/D
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
16 Plastic DIP
16 Plastic DIP
16 QSOP
CS
DIN
SCLK
9 DGND
16 QSOP
Dice*
DIP/QSOP
MAX5153AEPE -40°C to +85°C
MAX5153BEPE -40°C to +85°C
MAX5153AEEE -40°C to +85°C
MAX5153BEEE -40°C to +85°C
16 Plastic DIP
16 Plastic DIP
16 QSOP
16 QSOP
MAX5153BMJE -55°C to +125°C 16 CERDIP**
*Dice are tested at T = +25°C, DC parameters only.
A
**Contact factory for availability.
___________________Ch ip In fo rm a t io n
TRANSISTOR COUNT: 3053
SUBSTRATE CONNECTED TO AGND
______________________________________________________________________________________ 17
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
________________________________________________________P a c k a g e In fo rm a t io n
2/MAX153
18 ______________________________________________________________________________________
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
2/MAX153
___________________________________________P a c k a g e In fo rm a t io n (c o n t in u e d )
______________________________________________________________________________________ 19
Lo w -P o w e r, Du a l, 1 3 -Bit Vo lt a g e -Ou t p u t DACs
w it h Co n fig u ra b le Ou t p u t s
___________________________________________P a c k a g e In fo rm a t io n (c o n t in u e d )
2/MAX153
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
20 ____________________Ma x im In t e g ra t e d P ro d u c t s , 1 2 0 S a n Ga b rie l Drive , S u n n yva le , CA 9 4 0 8 6 4 0 8 -7 3 7 -7 6 0 0
© 1997 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
相关型号:
MAX5153ACEE+
D/A Converter, 1 Func, Serial Input Loading, 16us Settling Time, PDSO16, 0.150 INCH, 0.025 INCH PITCH, QSOP-16
MAXIM
MAX5153ACEE-T
D/A Converter, 1 Func, Serial Input Loading, 16us Settling Time, PDSO16, 0.150 INCH, 0.025 INCH PITCH, QSOP-16
MAXIM
MAX5153ACPE+
D/A Converter, 2 Func, Serial Input Loading, 16us Settling Time, PDIP16, 0.300 INCH, PLASTIC, DIP-16
MAXIM
MAX5153AEEE
DUAL, SERIAL INPUT LOADING, 16us SETTLING TIME, 13-BIT DAC, PDSO16, 0.150 INCH, 0.025 INCH PITCH, QSOP-16
ROCHESTER
MAX5153AEEE+
D/A Converter, 2 Func, Serial Input Loading, 16us Settling Time, PDSO16, 0.150 INCH, 0.025 INCH PITCH, QSOP-16
MAXIM
MAX5153AEEE+T
D/A Converter, 2 Func, Serial Input Loading, 16us Settling Time, PDSO16, 0.150 INCH, 0.025 INCH PITCH, QSOP-16
MAXIM
MAX5153AEPE
DUAL, SERIAL INPUT LOADING, 16us SETTLING TIME, 13-BIT DAC, PDIP16, 0.300 INCH, PLASTIC, DIP-16
ROCHESTER
©2020 ICPDF网 联系我们和版权申明