首页 |元器件品牌

MAX6756UKLD0+T [MAXIM]

Power Supply Support Circuit, Adjustable, 1 Channel, +5VV, BICMOS, PDSO5, SOT-23, 5 PIN;
MAX6756UKLD0+T
型号： MAX6756UKLD0+T
厂家： MAXIM INTEGRATED PRODUCTS    MAXIM INTEGRATED PRODUCTS
描述：

Power Supply Support Circuit, Adjustable, 1 Channel, +5VV, BICMOS, PDSO5, SOT-23, 5 PIN

信息通信管理 光电二极管
文件： 总18页 (文件大小：1078K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
General Description  
Benefits and Features  
● Single/Dual-Supply Voltage Monitors  
The MAX6754–MAX6764 low-power window detec-  
tors monitor undervoltage/overvoltage conditions on  
system power supplies. These devices assert when the  
monitored voltage is under the undervoltage and/or over  
the overvoltage thresholds.  
● Factory-Trimmed Window Threshold Options for 5V,  
3.3V, 3V, 2.5V, 1.8V, 1.5V, 1.2V, and 0.9V Supplies  
● Externally Adjustable Window Monitoring Options for  
Supplies Down to 0.5V  
The MAX6754–MAX6759/MAX6763/MAX6764 monitor  
a single voltage. The MAX6760/MAX6761/MAX6762  
monitor dual-voltage systems. The MAX6754/MAX6755/  
MAX6756 provide a single undervoltage/overvoltage  
output and the MAX6757–MAX6764 provide independent  
undervoltage and overvoltage outputs. The outputs are  
available in push-pull or open-drain configurations.  
● Selectable Window Threshold Options (±5%, ±10%, ±15%)  
● Single (Combined UV/OV) or Dual (Separate UV and  
OV) Outputs  
● 20μs (typ) or 100ms (min) Timeout Period Options  
(MAX6754–MAX6762)  
● Manual Reset Input (MAX6754–MAX6762)  
● Latched Overvoltage Output Function  
The MAX6754–MAX6762 offer factory-fixed voltage  
thresholds for monitoring system voltages from 0.9V to  
5V with a selectable ±5%, ±10%, or ±15% window voltage.  
The MAX6763/MAX6764 allow for externally adjustable  
thresholds. The MAX6754–MAX6762 are available in  
two delay-timing options (20μs, typ or 100ms, min). The  
MAX6760/MAX6761/MAX6762 also include a latched  
overvoltage output function and the MAX6754–MAX6762  
include a manual reset input.  
(MAX6760/MAX6761/MAX6762)  
● Immune to Short Voltage Transients  
● Low 10μA Supply Current  
● Low-Voltage Operation (Outputs Valid for VCC  
Down to 1V)  
● -40°C to +125°C Operating Temperature Range  
● Small SOT23 and TDFN Packages  
● AEC-Q100 Qualified (/V Parts Only, Refer to  
Ordering Information)  
This family of products is available in small SOT23 and  
TDFN packages, and is specified over the extended  
temperature range of -40°C to +125°C.  
Typical Application Circuit  
Applications  
● Telecommunications  
● Networking  
V
CC  
● Computers/Servers  
● Data Storage  
µP  
MAX6757  
● Power Metering  
● DC-DC Converter Modules  
● Automotive  
V
SET  
OV  
CC  
GND  
NMI  
MR  
UV  
RESET  
Pin Configurations appear towards end of data sheet.  
Ordering Information appears at end of data sheet.  
19-3075; Rev 10; 11/17  
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Absolute Maximum Ratings  
(Voltages with respect to GND.)  
Operating Temperature Range...............................-40°C to +125°C  
V
, V  
, ................................................................ -0.3V to +6.5V  
+ 0.3V)  
Junction Temperature ............................................................+150°C  
Storage Temperature Range ..................................-65°C to +150°C  
Lead Temperature (soldering, 10s) .......................................+300°C  
Soldering Temperature (reflow)  
Lead(Pb)-Free Package ....................................................+260°C  
Containing Lead(Pb)..........................................................+240°C  
CC CC2  
SET, OVLATCH, MR, UVIN, OVIN.................-0.3V to (V  
CC  
UV, RESET, OV (open drain).................................... -0.3V to +6.5V  
RESET, OV, UV, UV, RESET (push-pull) ......-0.3V to (V + 0.3V)  
CC  
Input/Output Current (all pins) ..................................................20mA  
Continuous Power Dissipation (T = +70°C)  
A
5-Pin SOT23-5 (derate 7.1mW/°C above T = +70°C)... 571mW  
A
6-Pin SOT23-6 (derate 8.7mW/°C above T = +70°C)... 696mW  
A
8-Pin TDFN (derate 24.4mW/°C above T = +70°C).... 1951mW  
A
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these  
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect  
device reliability.  
Electrical Characteristics  
(V  
= 1.0V to 6.0V, V  
= 0 to 6.0V (MAX6760–MAX6762), T = -40°C to +125°C, unless otherwise noted. Typical values are at  
CC  
CC2 A  
T
= +25°C.) (Note 1)  
A
PARAMETER  
SYMBOL  
CONDITIONS  
MIN  
TYP  
MAX  
UNITS  
POWER REQUIREMENTS  
(Note 2)  
1.0  
1.4  
6.0  
6.0  
Operating Voltage Range  
V
V
MAX6760TAAA/MAX6761TAAA/  
MAX6762TAAA/MAX6763/MAX6764UT-T  
CC  
V
V
V
= 3.6V, MAX6754–MAX6759, no load  
= 3.6V, MAX6763/MAX6764, no load  
13  
10  
30  
23  
CC  
CC  
CC  
V
V
Supply Current  
I
µA  
CC  
CC  
= 3.6V, V  
≥ V  
,
CC  
CC2  
13  
1
30  
1.5  
+20  
MAX6760/MAX6761/MAX6762, no load  
V
= 1.8V, V ≥ V  
,
CC2  
CC2  
CC  
Supply Current  
µA  
nA  
CC2  
MAX6760/MAX6761/MAX6762  
I
CC2  
V
(MAX6760–MAX6762TA_AD_)  
CC2  
Adjustable Bias Current  
-20  
(Note 3)  
V
THRESHOLD  
CC  
V
= V  
5.750  
5.500  
5.250  
3.795  
3.630  
3.465  
3.450  
3.300  
3.150  
2.875  
2.750  
2.625  
2.070  
1.980  
1.890  
5.875  
5.625  
5.375  
3.878  
3.713  
3.548  
3.525  
3.375  
3.225  
2.938  
2.813  
2.688  
2.115  
2.025  
1.935  
6.000  
5.750  
5.500  
3.960  
3.795  
3.630  
3.600  
3.450  
3.300  
3.000  
2.875  
2.750  
2.160  
2.070  
1.980  
SET  
SB  
L, 5V  
SET = V  
CC  
SET = GND  
= V  
V
SET  
SB  
T, 3.3V  
SET = V  
CC  
SET = GND  
= V  
SB  
V
T
= -40°C to  
SET  
A
V
Overvoltage Threshold  
OV  
+125°C, rising R, 3.0V  
SET = V  
CC  
V
CC  
TH  
V
CC  
SET = GND  
= V  
V
SET  
SB  
Z, 2.5V  
W, 1.8V  
SET = V  
CC  
SET = GND  
= V  
V
SET  
SB  
SET = V  
CC  
SET = GND  
Maxim Integrated  
│ 2  
www.maximintegrated.com  
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Electrical Characteristics (continued)  
(V  
= 1.0V to 6.0V, V  
= 0 to 6.0V (MAX6760–MAX6762), T = -40°C to +125°C, unless otherwise noted. Typical values are at  
CC  
CC2 A  
T
= +25°C.) (Note 1)  
A
PARAMETER  
SYMBOL  
CONDITIONS  
= V  
MIN  
TYP  
MAX  
4.250  
4.500  
4.750  
2.805  
2.970  
3.135  
2.550  
2.700  
2.850  
2.125  
2.250  
2.375  
1.530  
1.620  
1.710  
3.960  
3.795  
3.630  
3.600  
3.450  
3.300  
3.000  
2.875  
2.750  
2.160  
2.070  
1.980  
1.800  
1.725  
1.650  
1.440  
1.380  
1.320  
1.080  
1.035  
0.990  
0.511  
0.489  
0.468  
UNITS  
V
4.000  
4.250  
4.500  
2.640  
2.805  
2.970  
2.400  
2.550  
2.700  
2.000  
2.125  
2.250  
1.440  
1.530  
1.620  
3.795  
3.630  
3.465  
3.450  
3.300  
3.150  
2.875  
2.750  
2.625  
2.070  
1.980  
1.890  
1.725  
1.650  
1.575  
1.380  
1.320  
1.260  
1.035  
0.990  
0.945  
0.489  
0.468  
0.447  
4.125  
4.375  
4.625  
2.723  
2.888  
3.053  
2.475  
2.625  
2.775  
2.063  
2.188  
2.313  
1.485  
1.575  
1.665  
3.878  
3.713  
3.548  
3.525  
3.375  
3.225  
2.938  
2.813  
2.688  
2.115  
2.025  
1.935  
1.763  
1.688  
1.613  
1.410  
1.350  
1.290  
1.058  
1.013  
0.968  
0.500  
0.479  
0.457  
SET  
SB  
L, 5V  
SET = V  
CC  
SET = GND  
= V  
V
SET  
SB  
T, 3.3V SET = V  
CC  
SET = GND  
= V  
SB  
V
SET  
T
= -40°C  
A
V
Undervoltage Threshold  
UV  
to +125°C, R, 3.0V SET = V  
V
CC  
TH  
CC  
falling V  
CC  
SET = GND  
= V  
V
SET  
SB  
Z, 2.5V SET = V  
CC  
SET = GND  
= V  
V
SET  
SB  
W, 1.8V SET = V  
CC  
SET = GND  
= V  
V
SET  
SB  
T, 3.3V SET = V  
CC  
SET = GND  
= V  
V
SET  
SB  
R, 3.0V SET = V  
CC  
SET = GND  
= V  
V
SET  
SB  
Z, 2.5V SET = V  
CC  
SET = GND  
= V  
V
SET  
SB  
W, 1.8V SET = V  
CC  
T
= -40°C  
A
SET = GND  
= V (Note 2)  
V
Overvoltage Threshold  
OV  
to +125°C,  
rising V  
V
CC2  
TH2  
V
SET  
SB  
CC2  
I, 1.5V SET = V  
(Note 2)  
CC  
SET = GND (Note 2)  
= V (Note 2)  
V
SET  
SB  
G, 1.2V SET = V  
(Note 2)  
CC  
SET = GND (Note 2)  
= V (Note 2)  
V
SET  
SB  
E, 0.9V SET = V  
(Note 2)  
CC  
SET = GND (Note 2)  
= V  
V
SET  
SB  
ADJ  
SET = V  
CC  
SET = GND  
Maxim Integrated  
│ 3  
www.maximintegrated.com  
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Electrical Characteristics (continued)  
(V  
= 1.0V to 6.0V, V  
= 0 to 6.0V (MAX6760–MAX6762), T = -40°C to +125°C, unless otherwise noted. Typical values are at  
CC  
CC2 A  
T
= +25°C.) (Note 1)  
A
PARAMETER  
SYMBOL  
CONDITIONS  
= V  
MIN  
TYP  
2.723  
2.888  
3.053  
2.475  
2.625  
2.775  
2.063  
2.188  
2.313  
1.485  
1.575  
1.665  
1.238  
1.313  
1.388  
0.990  
1.050  
1.110  
0.743  
0.788  
0.833  
0.351  
0.372  
0.394  
0.7  
MAX  
2.805  
2.970  
3.135  
2.550  
2.700  
2.850  
2.125  
2.250  
2.375  
1.530  
1.620  
1.710  
1.275  
1.350  
1.425  
1.020  
1.080  
1.140  
0.765  
0.810  
0.855  
0.362  
0.383  
0.404  
UNITS  
V
2.640  
2.805  
2.970  
2.400  
2.550  
2.700  
2.000  
2.125  
2.250  
1.440  
1.530  
1.620  
1.200  
1.275  
1.350  
0.960  
1.020  
1.080  
0.720  
0.765  
0.810  
0.340  
0.362  
0.383  
SET  
SB  
T, 3.3V SET = V  
CC  
SET = GND  
= V  
V
SET  
SB  
R, 3.0V SET = V  
CC  
SET = GND  
= V  
V
SET  
SB  
Z, 2.5V SET = V  
CC  
SET = GND  
= V  
V
SET  
SB  
W, 1.8V SET = V  
CC  
T
= -40°C  
A
SET = GND  
= V (Note 2)  
to +125°C,  
falling  
V
V
Undervoltage Threshold  
UV  
V
CC2  
TH2  
V
SET  
SB  
CC2  
I, 1.5V SET = V  
(Note 2)  
CC  
SET = GND (Note 2)  
= V (Note 2)  
V
SET  
SB  
G, 1.2V SET = V  
(Note 2)  
CC  
SET = GND (Note 2)  
= V (Note 2)  
V
SET  
SB  
E, 0.9V SET = V  
(Note 2)  
CC  
SET = GND (Note 2)  
= V  
V
SET  
SB  
ADJ  
SET = V  
CC  
SET = GND  
Threshold Hysteresis  
V
V
, V  
%
HYST  
CC CC2  
UNDERVOLTAGE/OVERVOLTAGE INPUTS (UVIN, OVIN) (MAX6763/MAX6764)  
UVIN, OVIN Threshold Voltage  
UVIN, OVIN Input Bias Current  
V
0.485  
-20  
0.5  
0.7  
0.515  
+20  
V
TH-IN  
I
(Note 3)  
nA  
IN  
UVIN, OVIN Threshold  
Hysteresis  
V
%
HYST  
Maxim Integrated  
│ 4  
www.maximintegrated.com  
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Electrical Characteristics (continued)  
(V  
= 1.0V to 6.0V, V  
= 0 to 6.0V (MAX6760–MAX6762), T = -40°C to +125°C, unless otherwise noted. Typical values are at  
CC  
CC2 A  
T
= +25°C.) (Note 1)  
A
PARAMETER  
SYMBOL  
CONDITIONS  
MIN  
TYP  
MAX  
UNITS  
TIMING CHARACTERISTICS  
D0  
D3  
20  
µs  
Reset and UV Timeout Period  
t
Figure 7  
/V  
RP  
100  
185  
320  
ms  
V
falling at 10mV/µs from  
CC CC2  
V
to Reset Delay  
to UV Delay  
t
20  
20  
µs  
µs  
CC  
CC  
D-RESET  
UV + 100mV to UV - 100mV  
TH  
TH  
V
/V  
rising at 10mV/µs from  
CC CC2  
V
t
D-UV  
OV - 100mV to OV + 100mV  
TH  
TH  
V
/V  
rising at 10mV/µs from  
CC CC2  
V
to OV Delay  
t
OV - 100mV to OV + 100mV  
20  
µs  
CC  
D-OV  
TH  
TH  
(MAX6757–MAX6762 only)  
UVIN to UV Delay  
OVIN to OV Delay  
Startup Delay Time  
(MAX6763/MAX6764)  
20  
20  
2
µs  
µs  
(MAX6763/MAX6764)  
t
ms  
D0 options only, OV output (Note 4)  
START  
THRESHOLD WINDOW SELECT INPUT (SET)  
Input-Voltage Low  
0
0.1  
V
V
V
= 1.4V  
= 3.0V  
= 6.0V  
0.65  
0.81  
1.10  
0.75  
2.19  
4.90  
CC  
CC  
CC  
Input Bias Voltage  
(Note 5)  
V
V
V
SB  
Input-Voltage High  
Input Current  
V
- 0.1  
V
V
CC  
CC  
I
-1  
+1  
µA  
SET  
MANUAL RESET (MR)  
0.23 x  
Input-Voltage Low  
V
V
V
CC  
0.6 x  
Input-Voltage High  
V
CC  
Pullup Resistance to V  
Minimum Pulse Width  
Transient Immunity  
26  
kΩ  
µs  
ns  
CC  
4
300  
300  
40  
t
t
MR falling, Figure 7  
MR rising, Figure 7  
D-MR  
ns  
Propagation Delay  
D0  
D3  
MR_P  
100  
185  
320  
ms  
OVERVOLTAGE OUTPUT LATCH CONTROL INPUT (OVLATCH)  
0.3 x  
Input-Voltage Low  
V
V
V
CC  
0.7 x  
Input-Voltage High  
V
CC  
Maxim Integrated  
│ 5  
www.maximintegrated.com  
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Electrical Characteristics (continued)  
(V  
= 1.0V to 6.0V, V  
= 0 to 6.0V (MAX6760–MAX6762), T = -40°C to +125°C, unless otherwise noted. Typical values are at  
CC  
CC2 A  
T
= +25°C.) (Note 1)  
A
PARAMETER  
SYMBOL  
CONDITIONS  
MIN  
TYP  
MAX  
UNITS  
Input Bias Current  
I
-1  
+1  
µA  
OVLATCH  
RESET, RESET, UV, UV, OV  
Any V  
output asserted  
≥ 1.0V, I  
= 100µA,  
= 200µA,  
= 1.0mA,  
CC  
SINK  
0.3  
0.3  
0.3  
0.3  
0.3  
Any V ≥ 1.2V, I  
CC  
SINK  
output asserted  
Any V ≥ 1.71V, I  
RESET, UV Output Low (Open  
Drain or Push-Pull)  
CC  
SINK  
V
V
OL  
output asserted  
Any V ≥ 2.85V, I  
output asserted  
= 2.0mA,  
= 4.0mA,  
SINK  
CC  
SINK  
Any V ≥ 4.75V, I  
CC  
output asserted  
Any V ≥ 1.71V, I  
output deasserted  
= 0.8mA,  
= 2.0mA,  
= 4.0mA,  
0.8 x  
V
CC  
CC  
SOURCE  
SOURCE  
SOURCE  
Any V ≥ 2.85V, I  
0.8 x  
RESET, UV Output High  
(Push-Pull)  
CC  
V
V
V
OH  
output deasserted  
V
CC  
Any V ≥ 4.75V, I  
0.8 x  
CC  
output deasserted  
V
CC  
Any V ≥ 1.71V, I  
= 1.0mA,  
CC  
SINK  
SINK  
0.3  
0.3  
0.3  
output deasserted  
RESET, UV Output Low  
(Push-Pull)  
Any V ≥ 2.85V, I  
= 2.0mA,  
= 4.0mA,  
CC  
V
OL  
output deasserted  
Any V ≥ 4.75V, I  
CC  
SINK  
output deasserted  
Any V ≥ 1.0V, I  
= 50µA,  
0.8 x  
CC  
SOURCE  
output asserted  
V
CC  
Any V ≥1.2V, I  
= 100µA,  
0.8 x  
CC  
SOURCE  
output asserted  
V
CC  
RESET, UV Output High  
(Push-Pull)  
Any V ≥ 1.71V, I  
output asserted  
= 0.8mA,  
= 2.0mA,  
= 4.0mA,  
0.8 x  
V
CC  
CC  
SOURCE  
SOURCE  
SOURCE  
V
V
OH  
Any V ≥ 2.85V, I  
0.8 x  
V
CC  
CC  
output asserted  
Any V ≥ 4.75V, I  
0.8 x  
CC  
output asserted  
V
CC  
Maxim Integrated  
│ 6  
www.maximintegrated.com  
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Electrical Characteristics (continued)  
(V  
= 1.0V to 6.0V, V  
= 0 to 6.0V (MAX6760–MAX6762), T = -40°C to +125°C, unless otherwise noted. Typical values are at  
CC  
CC2 A  
T
= +25°C.) (Note 1)  
A
PARAMETER  
SYMBOL  
CONDITIONS  
MIN  
TYP  
MAX  
UNITS  
Any V  
output asserted  
≥ 1.98V, I  
= 1.4mA,  
CC  
SINK  
SINK  
SINK  
0.3  
Any V ≥ 2.75V, I  
= 2.0mA,  
= 3.0mA,  
CC  
0.3  
0.3  
0.3  
OV Output Low  
(Open-Drain or  
Push-Pull)  
output asserted  
V
V
OL  
Any V ≥ 3.63V, I  
CC  
output asserted  
Any V ≥ 5.5V, I  
= 4.0mA,  
SINK  
CC  
output asserted  
Any V ≥ 1.0V, I  
= 50µA,  
0.8 x  
CC  
SOURCE  
output deasserted  
V
CC  
Any V ≥ 1.2V, I  
= 100µA,  
0.8 x  
CC  
SOURCE  
output deasserted  
V
CC  
Any V ≥ 1.98V, I  
output deasserted  
= 1.4mA,  
= 2.0mA,  
= 3.0mA,  
0.8 x  
V
CC  
CC  
SOURCE  
SOURCE  
SOURCE  
OV Output High  
(Push-Pull)  
V
V
OH  
Any V ≥ 2.75V, I  
0.8 x  
V
CC  
CC  
output deasserted  
Any V ≥ 3.63V, I  
0.8 x  
CC  
output deasserted  
V
CC  
Any V ≥ 5.5V, I  
= 4.5mA,  
SOURCE  
0.8 x  
CC  
output deasserted  
V
CC  
RESET, UV, OV Output Open-  
Drain Leakage Current  
I
Output not asserted  
1
µA  
LKG  
Note 1: Devices are production tested at +25°C. Overtemperature limits are guaranteed by design.  
Note 2: Voltage monitoring requires that V must be greater than or equal to 1.4V, but outputs remain asserted in the correct state  
CC  
for V  
down to 1.0V.  
CC  
Note 3: Guaranteed by design.  
Note 4: For D0 window detector options and OV outputs, startup delay time is the time required for the internal reference/circuitry to  
reach specified accuracy after the monitor is powered up from GND.  
Note 5: The input bias voltage is based off of V . The minimum value is given by the equation (0.1 x V  
+ 0.51)V and the  
CC  
CC  
maximum value is given by (0.9 x V  
- 0.51)V.  
CC  
Maxim Integrated  
│ 7  
www.maximintegrated.com  
Low-Power, Single/Dual-Voltage Window Detectors  
MAX6754–MAX6764  
Typical Operating Characteristics  
(V  
= 5V, V  
= 3.3V, T = +25°C, unless otherwise noted.)  
CC  
CC2 A  
OVERVOLTAGE THRESHOLD  
vs. TEMPERATURE  
UNDERVOLTAGE THRESHOLD  
vs. TEMPERATURE  
TRANSIENT IMMUNITY  
vs. THRESHOLD OVERDRIVE  
1.03  
1.03  
1.02  
1.01  
1.00  
0.99  
0.98  
0.97  
1000  
100  
10  
1.02  
1.01  
1.00  
0.99  
0.98  
0.97  
UNDERVOLTAGE THRESHOLD RISING  
UNDERVOLTAGE THRESHOLD FALLING  
OUTPUT ASSERTS  
ABOVE THIS LINE  
OVERVOLTAGE THRESHOLD RISING  
OVERVOLTAGE THRESHOLD FALLING  
NORMALIZED TO RISING  
NORMALIZED TO FALLING  
THRESHOLD AT T = +25°C  
THRESHOLD AT T = +25°C  
A
A
-40 -25 -10  
5
20 35 50 65 80 95 110 125  
-40 -25 -10  
5
20 35 50 65 80 95 110 125  
1
10  
100  
1000  
TEMPERATURE (°C)  
TEMPERATURE (°C)  
OVERDRIVE (mV)  
D3 TIMEOUT PERIOD  
vs. TEMPERATURE  
SUPPLY CURRENT vs. SUPPLY VOLTAGE  
20  
18  
16  
14  
12  
10  
8
194  
192  
190  
188  
186  
184  
182  
180  
T
A
T
A
T
A
T
A
= +125°C  
= +85°C  
= +25°C  
= -40°C  
6
1
2
3
4
5
6
-40 -25 -10  
5
20 35 50 65 80 95 110 125  
V
CC  
(V)  
TEMPERATURE (°C)  
OUTPUT-VOLTAGE LOW  
vs. SINK CURRENT  
OUTPUT-VOLTAGE HIGH  
vs. SOURCE CURRENT  
1.8  
1.6  
1.4  
1.2  
1.0  
0.8  
0.6  
0.4  
0.2  
0
0
-0.2  
-0.4  
-0.6  
-0.8  
-1.0  
-1.2  
-1.4  
-1.6  
-1.8  
V
CC  
V
CC  
V
CC  
V
CC  
= 5.0V  
= 3.3V  
= 2.5V  
= 1.8V  
V
= 5.0V  
CC  
V
= 3.3V  
CC  
V
CC  
= 1.8V  
V
CC  
= 2.5V  
0
5
10  
(mA)  
15  
20  
0
5
10  
15  
20  
I
I
(mA)  
SOURCE  
SINK  
Maxim Integrated  
│ 8  
www.maximintegrated.com  
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Pin Configurations  
TOP VIEW  
1
2
3
4
8
7
6
5
MR  
V
CC  
V
1
2
3
5
4
SET  
CC  
OVLATCH  
UV (UV)  
OV  
GND  
MAX6760  
MAX6761  
MAX6762  
MAX6754  
MAX6755  
MAX6756  
V
GND  
CC2  
SET  
MR  
RESET (RESET)  
TDFN  
( ) MAX6761 ONLY.  
SOT23  
( ) MAX6755 ONLY.  
V
1
2
3
6
5
4
SET  
V
1
6
OVIN  
OV  
CC  
CC  
MAX6757  
MAX6758  
MAX6759  
MAX6763  
MAX6764  
GND  
OV  
GND  
UVIN  
2
3
5
4
MR  
UV (UV)  
UV  
SOT23  
( ) MAX6758 ONLY.  
SOT23  
Pin Description  
PIN  
MAX6754/ MAX6757/ MAX6760/  
MAX6755/ MAX6758/ MAX6761/  
MAX6756 MAX6759 MAX6762  
NAME  
FUNCTION  
MAX6763/  
MAX6764  
Power Voltage Input. V  
powers the device. V  
is the monitored  
CC  
CC  
voltage. Connect V  
of the MAX6756 to an RC filter to ensure  
CC  
1
1
1
–
proper operation during extreme transition events. A 100Ω resistor  
in series with a 0.1µF bypass capacitor is sufficient for most  
applications. See Figure 9 for more details.  
V
CC  
—
2
—
2
—
2
1
2
Power Input. V  
Ground  
powers the device.  
CC  
GND  
Active-Low Manual Reset Input. Drive MR low to assert undervoltage  
and reset outputs. The asserted output remains asserted for the  
specified propagation delay period after MR goes high. MR is  
3
3
8
—
MR  
internally pulled up to V  
through a 26kΩ resistor.  
CC  
Reset Output. The Reset Output asserts when V  
is below the  
CC  
selected UV threshold or above the selected OV threshold.  
TH  
TH  
Reset output deasserts after the specified timeout period after V  
CC  
RESET/  
RESET  
4
—
—
—
rises above the UV threshold or drops below the OV threshold.  
TH TH  
MAX6754: Active-low push-pull output (RESET).  
MAX6755: Active-high push-pull output (RESET).  
MAX6756: Active-low open-drain output (RESET).  
Maxim Integrated  
│ 9  
www.maximintegrated.com  
 
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Pin Description (continued)  
PIN  
MAX6754/ MAX6757/ MAX6760/  
MAX6755/ MAX6758/ MAX6761/  
MAX6756 MAX6759 MAX6762  
NAME  
FUNCTION  
MAX6763/  
MAX6764  
Threshold Window Select Input. SET configures the undervoltage  
and overvoltage window range for the internal detectors. Connect  
5
6
4
—
SET  
SET to GND for ±5% window, or to V  
for ±10% window. Bias SET  
CC  
to V /2 for a ±15% window.  
CC  
Undervoltage Output. UV/UV asserts when the monitored supply/  
supplies are below the UV thresholds or MR is low. UV/UV  
TH  
deasserts after the specified timeout period when the monitored  
UV/  
UV  
supply/supplies rise above the UV thresholds or for the specified  
propagation delay after MR goes high.  
MAX6757/MAX6760: Active-low push-pull output (UV).  
MAX6758/MAX6761: Active-high push-pull output (UV).  
MAX6759/MAX6762: Active-low open-drain output (UV).  
TH  
—
—
4
6
3
—
—
V
Voltage Input. Input for the second window voltage monitor,  
CC2  
—
V
CC2  
and device output power supply when V  
> V  
.
CC2  
CC  
Active-Low Overvoltage Output. OV asserts low when the monitored  
supply/supplies are above their overvoltage threshold (OV ). OV  
TH  
goes high impedance immediately when the monitored supply/  
supplies drop below OV  
.
TH  
There is no timeout delay period for the OV output.  
For MAX6763/MAX6764, OV is low when OVIN is above the internal  
0.5V threshold. OV is high when OVIN is below the internal 0.5V  
threshold.  
5
5
5
OV  
MAX6757–MAX6762: Active-low open-drain output.  
MAX6763: Active-low push-pull output.  
MAX6764: Active-low open-drain output.  
Overvoltage Output Latch Control Input. Drive OVLATCH high  
to latch the overvoltage output for any V  
or V  
overvoltage  
CC  
CC2  
condition. Drive OVLATCH low to clear the latch after overvoltage  
conditions have been removed. The latch is transparent when  
OVLATCH is connected to GND. OVLATCH is a high-impedance  
input. Use external pullup or pulldown.  
7
—
OVLATCH  
Undervoltage Input. UV is low when UVIN is below the internal 0.5V  
threshold. UV is high when UVIN is above the internal 0.5V threshold.  
—
—
—
—
—
—
3
4
UVIN  
Undervoltage Output. UV is low when UVIN is below the internal  
0.5V threshold. UV is high when UVIN is above the internal 0.5V  
threshold. There is no timeout delay period for the UV output.  
UV  
Overvoltage Input. OV is low when OVIN is above the internal 0.5V  
threshold. OV is high when OVIN is below the internal 0.5V threshold.  
—
—
—
—
—
—
6
OVIN  
EP  
Exposed Pad (TDFN Only). EP is internally connected to GND.  
Leave EP unconnected or connect to GND.  
—
Maxim Integrated  
│ 10  
www.maximintegrated.com  
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Functional Diagrams  
V
CC  
MR  
ADJUST  
MONITOR  
VOLTAGE  
(RESET)/  
RESET  
TIMEOUT  
PERIOD  
OPTION  
UV  
TH  
UV MONITOR  
OV MONITOR  
SET  
OV  
TH  
GND  
UV THRESHOLD  
-5%, -10%, -15%  
OV THRESHOLD  
+5%, +10%, +15%  
MAX6754/MAX6755/MAX6756  
INTERNAL  
REFERENCE  
( ) MAX6755 ONLY.  
Figure 1. MAX6754/MAX6755/MAX6756 Functional Diagram  
V
CC  
ADJUST  
MONITOR  
VOLTAGE  
(UV)/  
UV  
TIMEOUT  
PERIOD  
OPTION  
UV  
OV  
TH  
UV MONITOR  
SET  
MR  
OV  
V
CC  
TH  
OV MONITOR  
GND  
UV THRESHOLD  
-5%, -10%, -15%  
OV THRESHOLD  
+5%, +10%, +15%  
MAX6757/MAX6758/MAX6759  
INTERNAL  
REFERENCE  
( ) MAX6758 ONLY.  
Figure 2. MAX6757/MAX6758/MAX6759 Functional Diagram  
Maxim Integrated  
│ 11  
www.maximintegrated.com  
 
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Functional Diagrams (continued)  
V
MR  
CC  
ADJUST  
MONITOR  
VOLTAGE  
(UV)/  
UV  
TIMEOUT  
PERIOD  
OPTION  
UV  
TH  
UV MONITOR  
OV MONITOR  
OV  
OV  
CIRCUIT  
OV  
TH  
SET  
UV THRESHOLD  
-5%, -10%, -15%  
OVLATCH  
OV THRESHOLD  
+5%, +10%, +15%  
INTERNAL  
REFERENCE  
GND  
UV  
TH  
UV MONITOR  
OV MONITOR  
ADJUST  
MONITOR  
VOLTAGE  
V
CC2  
MAX6760/  
MAX6761/MAX6762  
OV  
TH  
( ) MAX6761 ONLY.  
Figure 3. MAX6760/MAX6761/MAX6762 Functional Diagram  
Maxim Integrated  
│ 12  
www.maximintegrated.com  
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
and lower voltage thresholds to be set externally (down  
to 0.5V). The MAX6754–MAX6762 are available with  
two timing options (20μs propagation delay or 100ms  
minimum reset timeout).  
Functional Diagrams (continued)  
MAX6763/MAX6764  
UVIN  
Supply Voltages  
UV  
V
CC  
is the power-supply input and the monitored volt-  
age of the MAX6754–MAX6762. These devices feature  
a factory-trimmed V and V divider that sets the  
UV  
OV  
TH  
UV MONITOR  
CC  
CC2  
nominal input range (see Table 1 and Table 2). V  
for the  
CC  
INTERNAL  
REFERENCE  
0.5V  
V
GND  
CC  
MAX6763/MAX6764 is the power supply of the device and  
not the monitored voltage. For noisy systems, bypass V  
CC  
TH  
and V  
each with a 0.1μF capacitor to GND. Connect  
CC2  
V
of the MAX6756 to an RC filter to ensure proper  
CC  
OV  
operation during extreme transition events. A 100Ω resis-  
tor in series with a 0.1µF bypass capacitor is sufficient for  
most applications. See Figure 9 for more details.  
OVIN  
OV MONITOR  
Setting the Adjustable Nominal Voltage  
Threshold  
Figure 4. MAX6763/MAX6764 Functional Diagram  
The MAX6760/MAX6761/MAX6762 (versions with  
suffixes LA, TA, RA, ZA, WA, and AA) offer adjustable  
Detailed Description  
nominal voltage threshold to monitor V  
. Use an  
CC2  
The MAX6754–MAX6764 are low-power window voltage  
detectors capable of monitoring undervoltage and  
overvoltage conditions on system power supplies.  
Whenever a monitored voltage falls below its undervoltage  
threshold or exceeds its overvoltage threshold, these  
devices assert their outputs to notify the system (see  
Functional Diagrams).  
external voltage-divider to set the voltage at V  
to  
CC2  
0.4255V. Configure SET to select a monitor window of  
±5%, ±10%, or ±15% (see Figure 5). The MAX6760/  
MAX6761/MAX6762 suffix AA monitor only V  
and do  
CC2  
not monitor V  
.
CC  
The MAX6754/MAX6755/MAX6756 are single-voltage  
window detectors with internally fixed nominal voltage,  
externally adjustable set window, single reset undervoltage/  
overvoltage output, and a manual reset input.  
0.4255V +5%  
+10%  
V+  
+15%  
OV  
The MAX6757/MAX6758/MAX6759 are single-voltage  
window detectors with internally set nominal voltage,  
externally adjustable set window, separate undervoltage/  
overvoltage outputs, and manual reset input.  
R1  
V
CC2  
(UV)  
R2  
The MAX6760/MAX6761/MAX6762 are dual-voltage  
window detectors with internally/externally set nominal  
voltages, externally adjustable set window, separate  
undervoltage/overvoltage outputs, manual reset input, and  
overvoltage latch functions.  
UV  
0.4255V -5%  
-10%  
-15%  
MAX6760/MAX6761/MAX6762  
(SUFFIXES LA, TA, RA, ZA, WA, AA)  
The MAX6763/MAX6764 are single adjustable window  
detectors with separate undervoltage/overvoltage outputs.  
( ) MAX6761 ONLY.  
The MAX6754–MAX6762 offer factory-fixed voltage  
thresholds for monitoring system voltages from 0.9V to  
5V. The MAX6754–MAX6762 include a SET function to  
select the window voltage to ±5%, ±10%, or ±15%. The  
MAX6763/MAX6764 allow for externally adjustable upper  
Figure 5. Setting the Threshold Voltage of V  
CC2  
Maxim Integrated  
│ 13  
www.maximintegrated.com  
 
 
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Overvoltage Latch Control Input (OVLATCH)  
The MAX6760/MAX6761/MAX6762 provide an overvoltage  
latch control input (OVLATCH). Drive OVLATCH high  
V+  
R1  
to latch the overvoltage output for any V  
or V  
MAX6763/MAX6764  
CC  
CC2  
UVIN  
overvoltage condition. Drive OVLATCH low to clear the  
latch after overvoltage conditions have been removed.  
The latch is transparent when OVLATCH is connected to  
GND. OVLATCH is a high impedance input. Use external  
pullup or pulldown.  
UV  
UV  
OV  
TH  
UV MONITOR  
INTERNAL  
REFERENCE  
0.5V  
V
GND  
OV  
CC  
R2  
Reset, Undervoltage, and Overvoltage  
Outputs (RESET, RESET, UV, UV, OV)  
RESET, RESET, UV, UV, and OV outputs assert when  
TH  
the monitored supply is below the selected UV threshold  
TH  
or above the selected OV  
threshold. The reset output  
TH  
OVIN  
deasserts after the specified timeout period when the  
monitored supply rises above the UV threshold or  
OV MONITOR  
V+ x R3  
TH  
R3  
drops below the OV  
are referenced to V  
threshold. The push-pull versions  
TH  
.
OVERVOLTAGE ASSERTS WHEN  
UNDERVOLTAGE ASSERTS WHEN  
> 0.5V  
CC  
R1 + R2 + R3  
The MAX6760/MAX6761/MAX6762 monitor both V  
CC  
V+ x (R2 + R3)  
R1 + R2 + R3  
< 0.5V  
and V  
. An undervoltage/overvoltage condition on  
CC2  
either voltage supply asserts the corresponding output.  
Figure 6. Setting the Undervoltage/Overvoltage Window  
RESET and UV are guaranteed to be in the correct logic  
state when V  
or V  
> 1V.  
CC  
CC2  
Choose R2 to have a resistance of up to 500kΩ.  
Calculate R1 by:  
R1 = ((V+ - 0.4255V) x R2) / 0.4255V  
MR  
The MAX6763/MAX6764 provide inputs to a window  
detector allowing the programming of the threshold  
voltage to within V  
(see Figure 6).  
t
CC  
D-MR  
Choose R1, R2, and R3 such that:  
(V+ / (R1 + R2 + R3)) ≥ 1μA  
t
RESET, UV  
MR_P  
SET  
The MAX6754–MAX6762 allow the setting of the window  
voltage range of the voltage detector. Connect SET to  
Figure 7a. Manual RESET/RESET Timing Diagram  
GND to set a ±5% window. Connect SET to V  
for a  
CC  
±10% window. Bias SET to V  
/ 2 for a ±15% window.  
CC  
Manual Reset (MR)  
V
CC  
The MAX6754–MAX6762 include an active-low manual  
reset input. Drive MR low to assert a reset output  
(MAX6754/MAX6755/MAX6756) or an undervoltage output  
(MAX6757/MAX6758/MAX6759). The output remains  
asserted for the specified propagation delay time (see  
Figure 7a and Figure 7b) after MR goes high. MR is inter-  
t
D-UV  
RESET, UV  
t
RP  
nally pulled to V  
with a 26kΩ resistor.  
CC  
(RESET IS THE COMPLEMENT OF RESET)  
Figure 7b. V /RESET, UV Timing Diagram  
CC  
Maxim Integrated  
│ 14  
www.maximintegrated.com  
 
 
 
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
turns the SCR on, blowing the fuse to disconnect the  
circuit from the power source. An optional capacitor (C1)  
on the gate of the SCR provides additional transient  
Applications Information  
Microprocessor Monitoring  
Figure 8 shows a microprocessor monitoring circuit. An  
overvoltage condition on either the core or I/O supply  
immunity against nuisance trips.  
CORE  
DC-DC  
CORE  
CONVERTER  
FUSE  
I/O  
DC-DC  
I/O  
CONVERTER  
UNREGULATED  
POWER SOURCE  
mP  
MAX6760  
V
V
MR  
OVLATCH  
UV  
CC2  
PUSH BUTTON  
CC  
GND  
SET  
RESET  
100kΩ  
100kΩ  
SCR  
OV  
NMI  
100kΩ  
*C1  
1mF  
*OPTIONAL.  
Figure 8. Microprocessor Monitoring  
VCC  
VCC  
100Ω  
SET  
VCC  
VCC  
0.1µF  
10kΩ  
MAX6756  
µP  
RESET  
RESET  
NMI  
GND  
MR  
Figure 9. MAX6756 Input Filter Connection  
Maxim Integrated  
│ 15  
www.maximintegrated.com  
 
 
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Table 1. Window Threshold Voltage  
Table 3. Timeout Period Suffix Guide  
Suffix Guide Single Fixed V  
(MAX6754—MAX6759)  
CC  
ACTIVE TIMEOUT PERIOD  
TIMEOUT  
PERIOD SUFFIX  
MIN (ms)  
Typ (ms)  
0.02  
MAX (ms)  
PART NO. SUFFIX  
V
NOMINAL SYSTEM VOLTAGE (V)  
CC  
D0  
D3  
—
—
L
T
5.0  
3.3  
3.0  
2.5  
1.8  
100  
185  
320  
R
Z
Standard Versions Table  
PART  
PART  
W
MAX6754UKLD0  
MAX6754UKLD3  
MAX6754UKTD0  
MAX6754UKTD3  
MAX6754UKZD0  
MAX6754UKZD3  
MAX6754UKWD0  
MAX6754UKWD3  
MAX6755UKLD0  
MAX6755UKLD3  
MAX6755UKTD0  
MAX6755UKTD3  
MAX6755UKZD0  
MAX6755UKZD3  
MAX6755UKWD0  
MAX6755UKWD3  
MAX6756UKLD0  
MAX6756UKLD3  
MAX6756UKTD0  
MAX6756UKTD3  
MAX6756UKZD0  
MAX6756UKZD3  
MAX6756UKWD0  
MAX6756UKWD3  
MAX6757UTTD0  
MAX6757UTTD3  
MAX6757UTLD0  
MAX6757UTLD3  
MAX6757UTZD0  
MAX6757UTZD3  
MAX6757UTWD0  
MAX6757UTWD3  
MAX6758UTLD0  
MAX6758UTLD3  
MAX6758UTTD0  
MAX6758UTTD3  
MAX6758UTZD0  
MAX6758UTZD3  
MAX6758UTWD0  
MAX6758UTWD3  
MAX6759UTLD0  
MAX6759UTLD3  
MAX6759UTTD0  
MAX6759UTTD3  
MAX6759UTZD0  
MAX6759UTZD3  
MAX6759UTWD0  
MAX6759UTWD3  
MAX6760TALTD3  
MAX6760TALAD3  
MAX6760TATZD3  
MAX6760TATWD3  
MAX6760TATAD3  
MAX6760TARAD3  
MAX6760TAZWD3  
MAX6760TAZAD3  
MAX6760TAWED3  
MAX6760TAWAD3  
MAX6761TALTD3  
MAX6761TALAD3  
MAX6761TATZD3  
MAX6761TATWD3  
MAX6761TATAD3  
MAX6761TARAD3  
MAX6761TAZWD3  
MAX6761TAZAD3  
MAX6761TAWED3  
MAX6761TAWAD3  
MAX6762TALTD3  
MAX6762TALAD3  
MAX6762TATZD3  
MAX6762TATWD3  
MAX6762TATAD3  
MAX6762TARAD3  
MAX6762TAZWD3  
MAX6762TAZAD3  
MAX6762TAWED3  
MAX6762TAWAD3  
MAX6763UT  
Table 2. Window Threshold Voltage  
Suffix Guide Dual Fixed/Adjustable  
(MAX6760/MAX6761/MAX6762)  
V
NOMINAL  
V
NOMINAL  
CC  
CC2  
PART NO.  
SUFFIX  
SYSTEM VOLTAGE  
SYSTEM VOLTAGE  
(V)  
(V)  
LT  
LR  
LA  
TZ  
TW  
TI  
5
3.3  
3.0  
5
5
ADJ*  
2.5  
3.3  
3.3  
3.3  
3.3  
3.3  
3.3  
3.0  
3.0  
3.0  
3.0  
3.0  
3.0  
2.5  
2.5  
2.5  
2.5  
2.5  
1.8  
1.8  
1.8  
1.8  
—
1.8  
1.5  
TG  
TE  
TA  
1.2  
0.9  
ADJ*  
2.5  
RZ  
RW  
RI  
1.8  
1.5  
RG  
RE  
RA  
ZW  
ZI  
1.2  
0.9  
ADJ*  
1.8  
1.5  
ZG  
ZE  
ZA  
WI  
WG  
WE  
WA  
AA  
1.2  
0.9  
ADJ*  
1.5  
1.2  
0.9  
ADJ*  
ADJ*  
MAX6764UT  
*See the Setting the Adjustable Nominal Voltage Threshold section.  
Maxim Integrated  
│ 16  
www.maximintegrated.com  
 
 
 
 
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Selector Guide  
PUSH-PULL PUSH-PULL OPEN-DRAIN PUSH-PULL PUSH-PULL OPEN-DRAIN PUSH-PULL OPEN-DRAIN  
RESET  
RESET  
RESET  
—
—
X
UV  
UV  
UV  
OV  
OV  
MAX6754  
MAX6755  
MAX6756  
MAX6757  
MAX6758  
MAX6759  
MAX6760  
MAX6761  
MAX6762  
MAX6763  
MAX6764  
X
—
X
—
—
—
X
—
—
—
—
X
—
—
—
—
—
X
—
—
—
—
—
—
—
—
—
X
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
X
X
X
X
X
X
—
X
—
—
X
—
—
X
—
—
X
—
—
X
—
—
—
—
X
—
—
Ordering Information  
Chip Information  
PROCESS: BiCMOS  
PART  
TEMP RANGE PIN-PACKAGE  
-40°C to +125°C 5 SOT23-5  
-40°C to +125°C 5 SOT23-5  
-40°C to +125°C 5 SOT23-5  
-40°C to +125°C 5 SOT23-5  
-40°C to +125°C 6 SOT23-6  
-40°C to +125°C 6 SOT23-6  
-40°C to +125°C 6 SOT23-6  
-40°C to +125°C 8 TDFN-EP  
-40°C to +125°C 8 TDFN-EP  
-40°C to +125°C 8 TDFN-EP  
-40°C to +125°C 6 SOT23-6  
-40°C to +125°C 6 SOT23-6  
MAX6754UK_D_-T  
MAX6755UK_D_-T  
MAX6756UK_D_-T  
MAX6756UK_D_/V+T  
MAX6757UT_D_-T  
MAX6758UT_D_-T  
MAX6759UT_D_/V-T  
MAX6760TA_ _D_-T  
MAX6761TA_ _D_-T  
MAX6762TA_ _D_-T  
MAX6763UT-T  
Package Information  
For the latest package outline information and land patterns  
(footprints), go to www.maximintegrated.com/packages. Note  
that a “+”, “#”, or “-” in the package code indicates RoHS status  
only. Package drawings may show a different suffix character, but  
the drawing pertains to the package regardless of RoHS status.  
PACKAGE  
TYPE  
PACKAGE  
CODE  
OUTLINE  
NO.  
LAND  
PATTERN NO.  
5 SOT23  
6 SOT23  
8 TDFN  
U5+1  
U6-1  
21-0057  
21-0058  
21-0137  
90-0174  
90-0175  
90-0059  
MAX6764UT-T  
T833-2  
Devices are available in both leaded and lead(Pb)-free packag-  
ing. Specify lead-free by replacing “-T” with “+T” when ordering.  
/V denotes an automotive qualified part.  
Insert the threshold level suffixes for V  
and V  
(see Table 1  
CC2  
CC  
and Table 2) after UK, UT, or TA. For the MAX6754–MAX6759,  
insert only the V threshold suffix after the UK or UT. Insert  
CC  
the reset timeout delay (see Table 3) after D to complete the  
part number. For example, the MAX6760TALTD3-T provides a  
V
threshold of 5V, a V  
threshold of 3.3V, and a 100ms  
CC  
CC2  
minimum reset timeout period. Sample stock is generally held  
on standard versions only (see the Standard Versions Table).  
Standard versions have an order increment requirement of 2500  
pieces. Nonstandard versions have an order increment require-  
ment of 10,000 pieces. Contact factory for availability.  
Maxim Integrated  
│ 17  
www.maximintegrated.com  
 
MAX6754–MAX6764  
Low-Power, Single/Dual-Voltage Window Detectors  
Revision History  
REVISION REVISION  
PAGES  
DESCRIPTION  
CHANGED  
NUMBER  
DATE  
Added /V to the MAX6759 Ordering Information and added soldering temperature  
in the Absolute Maximum Rating section  
4
1/11  
2, 16  
5
6
7
8
10/15  
11/15  
3/16  
Adding /V part number of MAX6756 to data sheet  
Updated package code for 5 SOT23 in Ordering Information section  
Re-added Standard Versions table  
1, 16–18  
19  
17–18  
17–18  
6/16  
Removed top mark information from Standard Versions table  
Moved Ordering Information and Selector Guide to end of data sheet and Pin  
Configurations to before Pin Description table; updated Pin Description (row 1),  
Supply Voltages section, and added Figure 9  
9
3/17  
1, 9, 13, 16, 17  
1
10  
11/17  
Added AEC statement to Benefits and Features section  
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.  
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses  
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits)  
shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.  
©
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.  
2017 Maxim Integrated Products, Inc.  
│ 18  

相关型号：

MAX6756UKLD0-T

 Power Supply Support Circuit, Adjustable, 1 Channel, +5VV, BICMOS, PDSO5, SOT-23, 5 PIN
MAXIM

MAX6756UKLD3

 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5, MO-178AA, SOT-23, 5 PIN
ROCHESTER

MAX6756UKLD3+

 Power Supply Support Circuit, Adjustable, 1 Channel, +5VV, BICMOS, PDSO5, MO-178AA, SOT-23, 5 PIN
MAXIM

MAX6756UKRD0+T

 Power Supply Support Circuit, Adjustable, 1 Channel, +3VV, BICMOS, PDSO5, LEAD FREE, MO-178AA, SOT-23, 5 PIN
MAXIM

MAX6756UKTD0+

 Power Supply Support Circuit, Adjustable, 1 Channel, +3.3VV, BICMOS, PDSO5, MO-178AA, SOT-23, 5 PIN
MAXIM

MAX6756UKTD3+

 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5, MO-178AA, SOT-23, 5 PIN
ROCHESTER

MAX6756UKTD3+T

 Power Supply Support Circuit, Adjustable, 1 Channel, +3.3VV, BICMOS, PDSO5, SOT-23, 5 PIN
MAXIM

MAX6756UKWD3

 Power Supply Support Circuit, Adjustable, 1 Channel, +1.8VV, BICMOS, PDSO5, MO-178AA, SOT-23, 5 PIN
MAXIM

MAX6756UKWD3+

 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5, MO-178AA, SOT-23, 5 PIN
ROCHESTER

MAX6756UKWD3+T

 Power Supply Support Circuit, Adjustable, 1 Channel, +1.8VV, BICMOS, PDSO5, SOT-23, 5 PIN
MAXIM

MAX6756UKWD3-T

 Power Supply Support Circuit, Adjustable, 1 Channel, +1.8VV, BICMOS, PDSO5, SOT-23, 5 PIN
MAXIM

MAX6756UKZD0+

 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5, MO-178AA, SOT-23, 5 PIN
ROCHESTER
©2020 ICPDF网 联系我们和版权申明