MAX8640YEXT19+ [MAXIM]
Switching Regulator/Controller, Voltage-mode, 2000kHz Switching Freq-Max, BICMOS, PDSO6,;型号: | MAX8640YEXT19+ |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | Switching Regulator/Controller, Voltage-mode, 2000kHz Switching Freq-Max, BICMOS, PDSO6, 信息通信管理 光电二极管 |
文件: | 总13页 (文件大小:545K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
EVALUATION KIT AVAILABLE
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
General Description
Features
o Tiny SC70 and µDFN Packages
The MAX8640Y/MAX8640Z step-down converters are
optimized for applications where small size, high effi-
ciency, and low output ripple are priorities. They utilize
a proprietary PWM control scheme that optimizes the
switching frequency for high efficiency with small exter-
nal components and maintains low output ripple volt-
age at all loads. The MAX8640Z switches at up to
4MHz to allow a tiny 1µH inductor and 2.2µF output
capacitor. The MAX8640Y switches at up to 2MHz for
higher efficiency while still allowing small 2.2µH and
4.7µF components. Output current is guaranteed up to
500mA, while typical quiescent current is 28µA.
Factory-preset output voltages from 0.8V to 2.5V elimi-
nate external feedback components.
o 500mA Guaranteed Output Current
o 4MHz or 2MHz PWM Switching Frequency
o Tiny External Components: 1µH/2.2µF or
2.2µH/4.7µF
o 28µA Quiescent Current
o Factory Preset Outputs from 0.8V to 2.5V
o
1ꢀ ꢁnitial Accuracy
o Low Output Ripple at All Loads
o Ultrasonic Skip Mode Down to 1mA Loads
o Ultra-Fast Line- and Load-Transient Response
o Fast Soft-Start Eliminates ꢁnrush Current
Ordering Information
Internal synchronous rectification greatly improves effi-
ciency and replaces the external Schottky diode
required in conventional step-down converters. Internal
fast soft-start eliminates inrush current so as to reduce
input capacitor requirements.
PꢁN-
PACKAGE
PART*
TOP MARK
MAX8640YEXT08+T
MAX8640YEXT10+T
MAX8640YEXT11+T
MAX8640YEXT12+T
MAX8640YEXT13+T
MAX8640YEXT15+T
MAX8640YEXT16+T
MAX8640YEXT18+T
MAX8640YEXT19+T
MAX8640YEXT82+T
6 SC70
6 SC70
6 SC70
6 SC70
6 SC70
6 SC70
6 SC70
6 SC70
6 SC70
6 SC70
ACQ
ADF
ACR
ACS
ACG
ADD
ADB
ACI
The MAX8640Y/MAX8640Z are available in the tiny 6-
pin, SC70 (2.0mm x 2.1mm) and µDFN (1.5mm x
1.0mm) packages. Both packages are lead-free.
Applications
Microprocessor/DSP Core Power
I/O Power
ACH
Cell Phones, PDAs, DSCs, MP3s
Other Handhelds Where Space Is Limited
ADJ
*Contact factory for availability of each version. For 2.85V output
(82 version), request application note that includes limitations
and typical operating characteristics.
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
Note: All devices are specified over the -40°C to +85°C
operating temperature range.
Ordering ꢁnformation continued and Selector Guide appears
at end of data sheet.
Pin Configurations
Typical Operating Circuit
TOP VIEW
OUTPUT
L1
1µH OR 2.2µH
+
+
INPUT
0.8V TO 2.5V
UP TO 500mA
2.7V TO 5.5V
IN
IN
6
LX
1
2
3
6
5
4
1
LX
IN
LX
MAX8640Y
MAX8640Z
MAX8640Y
MAX8640Z
MAX8640Y
MAX8640Z
C1
2.2µF
GND
GND
OUT
2
3
5
4
GND
GND
OUT
GND
OUT
C2
2.2µF OR
4.7µF
SHDN
SHDN
SHDN
ON/OFF
SC70
µDFN
2.0mm x 2.1mm
1.5mm x 1.0mm
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.
19-3997; Rev 5; 8/14
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
ABSOLUTE MAXꢁMUM RATꢁNGS
IN to GND.................................................................-0.3V to +6V
6-Pin µDFN (derate 2.1mW/°C above +70°C) ..............167.7mW
OUT, SHDN to GND ....................................-0.3V to (V + 0.3V)
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
IN
LX Current (Note 1) ........................................................0.8A
RMS
OUTPUT Short Circuit to GND ...................................Continuous
Continuous Power Dissipation (T = +70°C)
A
6-Pin SC70 (derate 3.1mW/°C above +70°C)..............245mW
Note 1: LX has internal clamp diodes to IN and GND. Applications that forward bias these diodes should not exceed the IC’s package
power-dissipation limit.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRꢁCAL CHARACTERꢁSTꢁCS
(V = 3.6V, SHDN = IN, T = -40°C to +85°C, typical values are at T = +25°C, unless otherwise noted.) (Note 2)
IN
A
A
PARAMETER
SYMBOL
CONDꢁTꢁONS
MꢁN
2.7
TYP
MAX UNꢁTS
Supply Range
V
5.5
2.70
48
V
V
IN
UVLO Threshold
UVLO
V
rising, 100mV hysteresis
2.44
2.6
28
IN
No load, no switching
Supply Current
I
µA
T
T
= +25°C
= +85°C
0.01
0.1
0.1
CC
A
SHDN = GND
A
Output Voltage Range
V
Factory preset
0.8
-1
2.5
+1
+2
V
OUT
I
= 0mA, T = +25°C
0
LOAD
LOAD
A
Output Voltage Accuracy
(Falling Edge)
%
I
= 0mA, T = -40°C to +85°C
-2
A
Output Load Regulation
(Voltage Positioning)
Equal to inductor DC resistance
R
V/A
V
L
V
V
V
= 2.7V to 5.5V
= 2.7V to 5.5V
1.4
IH
IN
IN
SHDN Logic Input Level
SHDN Input Bias Current
V
0.4
1
IL
T
T
= +25°C
= +85°C
0.001
0.01
A
V
= 5.5V,
IN
I
µA
µs
IH,IL
SHDN = GND or IN
A
Minimum Required SHDN Reset
Time
t
10
SHDN
Peak Current Limit
I
pFET switch
nFET rectifier
nFET rectifier
590
450
10
770
650
40
1400
1300
70
mA
mA
mA
LIMP
Valley Current Limit
I
LIMN
Rectifier Off-Current Threshold
I
LXOFF
R
pFET switch, I = -40mA
0.6
0.35
0.1
1
1.2
0.7
1
ONP
ONN
LX
On-Resistance
Ω
µA
ns
R
nFET rectifier, I = 40mA
LX
T
T
= +25°C
= +85°C
A
V
= 5.5V, LX = GND
IN
LX Leakage Current
Minimum On and Off Times
I
LXLKG
to IN, SHDN = GND
A
t
95
ON(MIN)
t
95
OFF(MIN)
Thermal Shutdown
+160
20
°C
°C
Thermal-Shutdown Hysteresis
Note 2: All devices are 100% production tested at T = +25°C. Limits over the operating temperature range are guaranteed by design.
A
2
Maxim Integrated
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
Typical Operating Characteristics
(V = 3.6V, V
IN
= 1.5V, MAX8640Z, L = Murata LQH32CN series, T = +25°C, unless otherwise noted.)
A
OUT
EFFICIENCY vs. LOAD CURRENT
1.8V OUTPUT
NO-LOAD SUPPLY CURRENT
vs. SUPPLY VOLTAGE
SWITCHING FREQUENCY
vs. LOAD CURRENT
100
90
80
70
60
50
40
30
20
10
0
10
35
30
25
20
15
10
5
MAX8640YEXT18
MAX8640YEXT18
MAX8640ZEXT15
MAX8640YEXT18
MAX8640ZEXT15
1
0.1
0.1
1
10
100
1000
2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5
SUPPLY VOLTAGE (V)
0
100
200
300
400
500
LOAD CURRENT (mA)
LOAD CURRENT (mA)
OUTPUT VOLTAGE vs. LOAD CURRENT
(VOLTAGE POSITIONING)
LIGHT-LOAD SWITCHING WAVEFORMS
(I = 1mA)
OUT
MAX8640Y/Z toc05
1.55
1.50
1.45
1.40
1.35
1.30
20mV/div
(AC-COUPLED)
V
MAX8640ZEXT15
OUT
V
I
LX
2V/div
LX
200mA/div
10μs/div
0
100
200
300
400
500
LOAD CURRENT (mA)
MEDIUM-LOAD SWITCHING WAVEFORMS
(I = 40mA)
HEAVY-LOAD SWITCHING WAVEFORMS
(I = 300mA)
OUT
OUT
MAX8640Y/Z toc06
MAX8640Y/Z toc07
20mV/div
(AC-COUPLED)
20mV/div
(AC-COUPLED)
V
V
OUT
OUT
2V/div
0V
V
I
V
I
LX
LX
2V/div
0V
200mA/div
200mA/div
0mA
LX
LX
0mA
200ns/div
200ns/div
Maxim Integrated
3
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
Typical Operating Characteristics (continued)
(V = 3.6V, V
IN
= 1.5V, MAX8640Z, L = Murata LQH32CN series, T = +25°C, unless otherwise noted.)
A
OUT
LIGHT-LOAD STARTUP WAVEFORM
HEAVY-LOAD STARTUP WAVEFORM
(100Ω LOAD)
(5Ω LOAD)
MAX8640Y/Z toc08
MAX8640Y/Z toc09
5V/div
5V/div
V
V
SHDN
SHDN
1V/div
0V
1V/div
0V
V
OUT
V
OUT
100mA/div
0mA
100mA/div
0mA
I
IN
I
IN
500mA/div
0mA
I
LX
I
LX
500mA/div
0mA
20μs/div
20μs/div
LINE-TRANSIENT RESPONSE
LOAD-TRANSIENT RESPONSE
(4V TO 3.5V TO 4V)
(5mA TO 250mA TO 5mA)
MAX8640Y/Z toc10
MAX8640Y/Z toc11
1V/div
4V
50m/div
AC-COUPLED
V
IN
V
OUT
500mA/div
I
LX
V
OUT
20mV/div
AC-COUPLED
200mA/div
0mA
I
200mA/div
0mA
I
LX
OUT
20μs/div
40μs/div
LOAD-TRANSIENT RESPONSE
(10mA TO 500mA TO 10mA)
MAX8640Y/Z toc12
100mV/div
V
OUT
AC-COUPLED
I
LX
500mA/div
0V
I
OUT
200mA/div
40μs/div
4
Maxim Integrated
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
Pin Description
PꢁN
1
NAME
LX
FUNCTꢁON
Inductor Connection to the Internal Drains of the p-channel and n-channel MOSFETs. High impedance
during shutdown.
2, 5
3
GND
OUT
Ground. Connect these pins together directly under the IC.
Output Sense Input. Bypass with a ceramic capacitor as close as possible to pin 3 (OUT) and pin 2 (GND).
OUT is internally connected to the internal feedback network.
Active-Low Shutdown Input. A logic-low on SH D N disables the step-down DC-DC and resets the logic. A logic-
high on SH D N enables the step-down DC-DC. Ensure that SH D N is low for ≥ 10µs (t
undervoltage lockout threshold (UVLO) to reset the logic. See the Shutdown Mode section for more information.
) after V rises above its
IN
4
6
SHDN
SHDN
Supply Voltage Input. Input voltage range is 2.7V to 5.5V. Bypass with a ceramic capacitor as close as
possible to pin 6 (IN) and pin 5 (GND).
IN
Voltage-Positioning Load Regulation
The MAX8640Y/MAX8640Z utilize a unique feedback
Detailed Description
The MAX8640Y/MAX8640Z step-down converters deliv-
er over 500mA to outputs from 0.8V to 2.5V. They utilize
a proprietary hysteretic PWM control scheme that
switches at up to 4MHz (MAX8640Z) or 2MHz
(MAX8640Y), allowing some trade-off between efficien-
cy and size of external components. At loads below
100mA, the MAX8640Y/MAX8640Z automatically switch
to pulse-skipping mode to minimize the typical quies-
cent current (28µA). Output ripple remains low at all
loads, while the skip-mode switching frequency
remains ultrasonic down to 1mA (typ) loads. Figure 1 is
the simplified functional diagram.
network. By taking DC feedback from the LX node, the
usual phase lag due to the output capacitor is
removed, making the loop exceedingly stable and
allowing the use of very small ceramic output capacitors.
This configuration yields load regulation equal to the
inductor’s series resistance multiplied by the load current.
This voltage-positioning load regulation greatly reduces
overshoot during load transients, effectively halving the
peak-to-peak output-voltage excursions compared to tra-
ditional step-down converters. See the Load-Transient
Response in the Typical Operating Characteristics.
Shutdown Mode
A logic-low on SHDN places the MAX8640Y/MAX8640Z
in shutdown mode by disabling the step-down DC-DC
and resetting its logic. In shutdown mode, the supply
Control Scheme
A proprietary hysteretic PWM control scheme ensures
high efficiency, fast switching, fast transient response,
low output ripple, and physically tiny external compo-
nents. This control scheme is simple: when the output
voltage is below the regulation threshold, the error
comparator begins a switching cycle by turning on the
high-side switch. This switch remains on until the mini-
mum on-time expires and the output voltage is above
the regulation threshold or the inductor current is above
the current-limit threshold. Once off, the high-side
switch remains off until the minimum off-time expires
and the output voltage falls again below the regulation
threshold. During the off period, the low-side synchro-
nous rectifier turns on and remains on until either the
high-side switch turns on again or the inductor current
approaches zero. The internal synchronous rectifier
eliminates the need for an external Schottky diode.
current (I ) is reduced to 0.01µA typical. Additionally,
CC
the power MOSFETs between IN, LX, and GND
(Figure 1) are open such that LX is high impedance.
Ensure that SHDN is low for ≥ 10µs (t
) after V
IN
SHDN
rises above its undervoltage lockout threshold (UVLO)
to reset the logic. In the majority of systems, this t
SHDN
requirement is fulfilled naturally because the upstream
logic controlling SHDN is powered off of the same V
IN
as the MAX8640Y/MAX8640Z. However, systems that
want an always on regulator without the burden of
enable/disable logic can use an R and C circuit on
SHDN as shown in Figure 2.
Maxim Integrated
5
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
as Li+ and alkaline cells. See the Soft-Start Response
in the Typical Operating Characteristics.
IN
Applications Information
The MAX8640Y/MAX8640Z are optimized for use with a
tiny inductor and small ceramic capacitors. The correct
selection of external components ensures high efficien-
cy, low output ripple, and fast transient response.
PWM
LOGIC
SHDN
LX
Inductor Selection
A 1µH inductor is recommended for use with the
MAX8640Z, and 2.2µH is recommended for the
MAX8640Y. A 1µH inductor is physically smaller but
requires faster switching, resulting in some efficiency
loss. Table 1 lists several recommended inductors.
GND
OUT
0.6V
It is acceptable to use a 1.5µH inductor with either the
MAX8640Y or MAX8640Z, but efficiency and ripple
should be verified. Similarly, it is acceptable to use a
3.3µH inductor with the MAX8640Y, but performance
should be verified.
MAX8640Y
MAX8640Z
For optimum voltage positioning of load transients,
choose an inductor with DC series resistance in the
75mΩ to 150mΩ range. For higher efficiency at heavy
loads (above 200mA) or minimal load regulation (but
some transient overshoot), the resistance should be
kept as low as possible. For light-load applications up
to 200mA, higher resistance is acceptable with very lit-
tle impact on performance.
Figure 1. Simplified Functional Diagram
MAX8640
IN
ESD
DIODE
100kΩ
Capacitor Selection
VIN
SHDN
Output Capacitor
The output capacitor, C2, is required to keep the output
voltage ripple small and to ensure regulation loop sta-
bility. C2 must have low impedance at the switching fre-
quency. Ceramic capacitors are recommended due to
their small size and low ESR. Make sure the capacitor
maintains its capacitance over temperature and DC
bias. Capacitors with X5R or X7R temperature charac-
teristics typically perform well. The output capacitance
can be very low; see the Selector Guide for recom-
mended capacitance values. For optimum load-tran-
sient performance and very low output ripple, the output
capacitor value in µF should be equal to or larger than
the inductor value in µH.
4.7nF
GND
Figure 2. Using an R and C circuit to create an always on regu-
lator
Soft-Start
The MAX8640Y/MAX8640Z include internal soft-start
circuitry that eliminates inrush current at startup, reduc-
ing transients on the input source. Soft-start is particu-
larly useful for higher impedance input sources, such
6
Maxim Integrated
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
Table 1. Suggested ꢁnductors
ꢁNDUCTANCE
(µH)
DC RESꢁSTANCE
CURRENT RATꢁNG
(mA)
DꢁMENSꢁONS
L x W x H (mm)
MANUFACTURER
SERꢁES
(Ω typ)
MIPFT2520D
2.0
1.5
2.2
3.3
1.0
1.5
2.2
1.2
1.5
2.2
1.0
1.5
2.2
1.0
2.2
1.0
2.2
1.0
2.2
1.0
2.2
1.0
2.2
0.16
0.07
0.08
0.10
0.12
0.16
0.22
0.08
0.09
0.12
0.11
0.13
0.14
0.15
0.36
0.07
0.10
0.10
0.20
0.05
0.08
0.07
0.14
900
1500
1300
1200
1200
1000
900
2.5 x 2.0 x 0.5
2.5 x 2.0 x 1.0
FDK
MIPF2520D
LQM31P
Murata
3.2 x 1.6 x 0.95
3.0 x 3.0 x 1.0
3.2 x 1.6 x 0.9
590
Sumida
CDRH2D09
CKP3216T
520
440
1100
1000
900
Taiyo Yuden
460
GLF201208T
GLF2012T
2.0 x 1.25 x 0.9
2.0 x 1.25 x 1.35
2.5 x 1.8 x 1.35
2.5 x 2.0 x 1.0
2.8 x 2.8 x 1.2
300
400
TDK
300
800
GLF251812T
MDT2520-CR
D2812C
600
1000
700
TOKO
1100
770
ꢁnput Capacitor
PCB Layout and Routing
High switching frequencies and large peak currents
make PCB layout a very important part of design. Good
design minimizes excessive EMI on the feedback paths
and voltage gradients in the ground plane, both of
which can result in instability or regulation errors.
Connect the inductor, input capacitor, and output
capacitor as close together as possible, and keep their
traces short, direct, and wide. Connect the two GND
pins under the IC and directly to the grounds of the
input and output capacitors. Keep noisy traces, such
as the LX node, as short as possible. Refer to the
MAX8640Z evaluation kit for an example PCB layout
and routing scheme.
The input capacitor, C1, reduces the current peaks
drawn from the battery or input power source and
reduces switching noise in the IC. The impedance of C1
at the switching frequency should be kept very low.
Ceramic capacitors are recommended due to their
small size and low ESR. Make sure the capacitor main-
tains its capacitance over temperature and DC bias.
Capacitors with X5R or X7R temperature characteristics
typically perform well. Due to the MAX8640Y/
MAX8640Z soft-start, the input capacitance can be very
low. For optimum noise immunity and low input ripple,
choose a capacitor value in µF that is equal to or larger
than the inductor’s value in µH.
Maxim Integrated
7
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
Selector Guide
RECOMMENDED COMPONENTS
OUTPUT
VOLTAGE (V)
FREQUENCY
(MHz)
PART
TOP MARK
C2 (µF)
10
L1 (µH)
2.2
MAX8640YEXT08
MAX8640YEXT10
MAX8640YEXT11
MAX8640YEXT12
MAX8640YEXT13
MAX8640YEXT15
MAX8640YEXT16
MAX8640YEXT18
MAX8640YEXT19
MAX8640YEXT24
MAX8640YEXT25
0.8
1.0
1.1
1.2
1.3
1.5
1.6
1.8
1.9
2.4
2.5
1.2
1.6
1.7
1.8
1.9
2.0
2.0
2.0
2.0
2.0
1.7
ACQ
ADF
ACR
ACS
ACG
ADD
ADB
ACI
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
10
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
ACH
ADM
ACJ
2.2
2.2
MAX8640YEXT82
MAX8640YELT08
2.85
0.8
1.5
1.2
2.2
2.2
ADJ
NB
MAX8640YELT11
MAX8640YELT12
MAX8640YELT13
MAX8640YELT15
MAX8640YELT16
MAX8640YELT18
MAX8640YELT19
MAX8640YELT25
MAX8640YELT82
1.1
1.2
1.3
1.5
1.6
1.8
1.9
2.5
2.85
1.7
1.8
1.9
2.0
2.0
2.0
2.0
1.7
1.5
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
2.2
2.2
2.2
2.2
2.2
4.7
2.2
NC
ND
NE
NF
NG
NH
NI
NJ
OW
MAX8640ZEXT08
MAX8640ZEXT11
MAX8640ZEXT12
MAX8640ZEXT13
MAX8640ZEXT15
MAX8640ZEXT18
MAX8640ZELT08
MAX8640ZELT11
0.8
1.1
1.2
1.3
1.5
1.8
0.8
1.1
2.4
3.4
3.6
3.7
3.9
4.0
2.4
3.4
1
1
1
1
1
1
1
1
ACL
ACM
ACN
ACO
ACP
ACU
NK
NL
8
Maxim Integrated
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
Selector Guide (continued)
RECOMMENDED COMPONENTS
OUTPUT
VOLTAGE (V)
FREQUENCY
(MHz)
PART
TOP MARK
C2 (µF)
2.2
L1 (µH)
MAX8640ZELT12
MAX8640ZELT13
MAX8640ZELT15
MAX8640ZELT18
1.2
1.3
1.5
1.8
3.6
3.7
3.9
4.0
1
1
1
1
NM
NN
NO
NP
2.2
2.2
2.2
Ordering Information (continued)
PꢁN-
PACKAGE
PꢁN-
PACKAGE
PART*
TOP MARK
PART*
TOP MARK
MAX8640YEXT24+T
MAX8640YEXT25+T
MAX8640YELT08+T
MAX8640YELT11+T
6 SC70
6 SC70
6 µDFN
6 µDFN
ADM
ACJ
NB
MAX8640ZEXT08+T
MAX8640ZEXT11+T
MAX8640ZEXT12+T
MAX8640ZEXT13+T
MAX8640ZEXT15+T
MAX8640ZEXT18+T
MAX8640ZELT08+T
MAX8640ZELT11+T
MAX8640ZELT12+T
MAX8640ZELT13+T
MAX8640ZELT15+T
MAX8640ZELT18+T
6 SC70
6 SC70
6 SC70
6 SC70
6 SC70
6 SC70
6 µDFN
6 µDFN
6 µDFN
6 µDFN
6 µDFN
6 µDFN
ACL
ACM
ACN
ACO
ACP
ACU
NK
NC
MAX8640YELT12+T
MAX8640YELT13+T
MAX8640YELT15+T
MAX8640YELT16+T
MAX8640YELT18+T
MAX8640YELT19+T
MAX8640YELT25+T
MAX8640YELT82+T
6 µDFN
6 µDFN
6 µDFN
6 µDFN
6 µDFN
6 µDFN
6 µDFN
6 µDFN
ND
NE
NF
NG
NH
NI
NL
NM
NN
NJ
NO
OW
NP
*Contact factory for availability of each version. For 2.85V output
(82 version), request application note that includes limitations
and typical operating characteristics.
+Denotes a lead(Pb)-free/RoHS-compliant package.
T = Tape and reel.
Note: All devices are specified over the -40°C to +85°C
Chip Information
PROCESS: BiCMOS
operating temperature range.
Maxim Integrated
9
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
Package Information
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the
package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
DOCUMENT NO.
6 µDFN
6 SC70
L611-1
X6S-1
21-0147
21-0077
SCOTT SCHROEDER
01/12/12
10
Maxim Integrated
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
Package Information (continued)
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the
package regardless of RoHS status.
SCOTT SCHROEDER
01/12/12
Maxim Integrated
11
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
Package Information (continued)
For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the
package regardless of RoHS status.
12
Maxim Integrated
MAX8640Y/MAX8640Z
Tiny 500mA, 4MHz/2MHz Synchronous
Step-Down DC-DC Converters
Revision History
REVꢁSꢁON
NUMBER
REVꢁSꢁON
DATE
PAGES
CHANGED
DESCRꢁPTꢁON
Added MAX8640YEXT10+T voltage option
3
4
6/08
7
Added MAX8640YEXT24+T voltage option and
MAX8640YELT82+MAX8640YEXT82+ (82 = 2.85V), and corrected error
2/09
8/14
1, 2, 7, 8
Updated Electrical Characteristics table, Pin Description, and Shutdown Mode
sections
5
2, 5
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and
max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 ________________________________ 13
© 2014 Maxim Integrated Products, Inc.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
相关型号:
MAX8640YEXT19-T
Switching Regulator/Controller, Voltage-mode, 2000kHz Switching Freq-Max, BICMOS, PDSO6
MAXIM
MAX8640YEXT25
Switching Regulator/Controller, Voltage-mode, 1700kHz Switching Freq-Max, BICMOS, PDSO6,
MAXIM
MAX8640YEXT25+
Switching Regulator/Controller, Voltage-mode, 1700kHz Switching Freq-Max, BICMOS, PDSO6,
MAXIM
MAX8640ZELT08+T
Switching Regulator, Voltage-mode, 1.4A, 4000kHz Switching Freq-Max, BICMOS, 1.50 X 1 MM, 0.80 MM HEIGHT, ROHS COMPLIANT, MO-252WAAD, MICRO, DFN-6
MAXIM
MAX8640ZELT11+T
Switching Regulator, Voltage-mode, 1.4A, 4000kHz Switching Freq-Max, BICMOS, 1.50 X 1 MM, 0.80 MM HEIGHT, ROHS COMPLIANT, MO-252WAAD, MICRO, DFN-6
MAXIM
©2020 ICPDF网 联系我们和版权申明