MAX8867EUK25 [MAXIM]
Fixed Positive LDO Regulator, 2.5V, PDSO5, MO-178, SOT-23, 5 PIN;型号: | MAX8867EUK25 |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | Fixed Positive LDO Regulator, 2.5V, PDSO5, MO-178, SOT-23, 5 PIN 光电二极管 输出元件 调节器 |
文件: | 总9页 (文件大小:458K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
19-1302; Rev 2; 3/01
Low-Noise, Low-Dropout,
150mA Linear Regulators in SOT23
_______________General Description
____________________________Features
The MAX8867/MAX8868 low-noise, low-dropout linear
regulators operate from a 2.5V to 6.5V input and deliver
up to 150mA. Typical output noise for these devices is
ꢀ Low Output Noise: 30µV
RMS
ꢀ Low 55mV Dropout at 50mA Output
(165mV at 150mA output)
just 30µV
, and typical dropout is only 165mV at
RMS
150mA. The output voltage is preset to voltages in the
range of 2.5V to 5.0V, in 100mV increments. The
MAX8867 and MAX8868 are pin-compatible with the
MAX8863 and MAX8864, except for the BP pin.
ꢀ Low 85µA No-Load Supply Current
ꢀ Low 100µA Operating Supply Current
(even in dropout)
Designed with an internal P-channel MOSFET pass
transistor, the MAX8867/MAX8868 maintain a low
100µA supply current, independent of the load current
and dropout voltage. Other features include a 10nA
logic-controlled shutdown mode, short-circuit and ther-
mal-shutdown protection, and reverse battery protec-
tion. The MAX8868 also includes an auto-discharge
function, which actively discharges the output voltage
to ground when the device is placed in shutdown. Both
devices come in a miniature 5-pin SOT23 package.
ꢀ Thermal-Overload and Short-Circuit Protection
ꢀ Reverse Battery Protection
ꢀ Output Current Limit
ꢀ Preset Output Voltages ( 1.4% accuracy)
ꢀ 10nA Logic-Controlled Shutdown
______________Ordering Information
________________________Applications
PART*
TEMP. RANGE
0°C to +70°C
-40°C to +85°C
0°C to +70°C
-40°C to +85°C
PIN-PACKAGE
Dice**
Cellular Telephones
Cordless Telephones
PCS Telephones
PCMCIA Cards
Modems
MAX8867C/Dxy
MAX8867EUKxy-T
MAX8868C/Dxy
MAX8868EUKxy-T
Hand-Held Instruments
Palmtop Computers
Electronic Planners
5 SOT23-5
Dice**
5 SOT23-5
* xy is the output voltage code (see Expanded Ordering
Information table).
__________________Pin Configuration
** Dice are tested at T = +25 C
A
TOP VIEW
SHDN
GND
IN
1
2
3
5
4
BP
___Expanded Ordering Information
MAX8867
MAX8868
PRESET
SOT TOP MARK
MAX8867 MAX8868
ACAY ACBF
OUTPUT
VOLTAGE (xy)
CODE
OUTPUT
VOLTAGE
(V)
OUT
MAX886_EUK25
MAX886_EUK28
MAX886_EUK29
MAX886_EUK30
MAX886_EUK32
MAX886_EUK33
MAX886_EUK36
MAX886_EUK50
Other xy***
2.50
2.80
2.84
3.00
3.15
3.30
3.60
5.00
x.y0
SOT23-5
ACAZ
ACBA
ACBB
ACBC
ACBD
ACCZ
ACBE
—
ACBG
ACBH
ACBI
ACBJ
ACBK
ACDA
ACBL
—
__________Typical Operating Circuit
INPUT
OUTPUT
2.5V TO 6.5V
PRESET
IN
OUT
2.5V TO 5.0V
150mA
C
1 F
IN
C
OUT
1 F
MAX8867
MAX8868
ON
SHDN
OFF
BP
***Other xy between 2.5V and 5.0V are available in 100mV incre-
ments. Contact factory for other versions. Minimum order
quantity is 25,000 units.
C
GND
BP
0.01 F
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Low-Noise, Low-Dropout,
150mA Linear Regulators in SOT23
ABSOLUTE MAXIMUM RATINGS
IN to GND....................................................................-7V to +7V
Output Short-Circuit Duration ............................................Infinite
SHDN to GND..............................................................-7V to +7V
SHDN to IN...............................................................-7V to +0.3V
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature......................................................+150°C
..................................................................................140°C/W
Storage Temperature Range.............................-65°C to +160°C
Lead Temperature (soldering, 10sec) .............................+300°C
JB
OUT, BP to GND..........................................-0.3V to (V + 0.3V)
IN
Continuous Power Dissipation (T = +70°C)
A
SOT23-5 (derate 7.1mW/°C above +70°C)...................571mW
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V = V
+ 0.5V, T = -40°C to +85°C, unless otherwise noted. Typical values are at T = +25°C.) (Note 1)
IN
OUT(NOMINAL)
A
A
PARAMETER
SYMBOL
CONDITIONS
MIN
2.5
-1.4
-3
TYP
MAX
6.5
1.4
2
UNITS
Input Voltage (Note 2)
V
IN
V
I
I
= 0mA, T = +25°C
OUT
A
Output Voltage Accuracy
%
= 0mA to 120mA
OUT
Maximum Output Current
Current Limit
150
160
mA
mA
I
390
85
LIM
No load
180
120
Ground-Pin Current
I
Q
µA
I
I
I
I
= 150mA
= 1mA
100
1.1
55
OUT
OUT
OUT
OUT
= 50mA
= 150mA
Dropout Voltage (Note 2)
mV
165
0
Line Regulation
Load Regulation
V
V
V
IN
= (V
+ 0.1V) to 6.5V, I = 1mA
OUT
-0.15
2.0
0.15
0.04
%/V
LNR
OUT
I
= 0mA to 120mA, C
= 1µF
0.01
30
%/mA
LDR
OUT
OUT
C
C
= 10µF
OUT
f = 10Hz to 100kHz,
= 0.01µF
Output Voltage Noise
SHUTDOWN
e
n
µV
RMS
C
BP
= 100µF
20
OUT
V
V
V
= 2.5V to 5.5V
= 2.5V to 5.5V
IH
IN
V
SHDN Input Threshold
V
0.4
IL
IN
T
A
T
A
T
A
T
A
T
A
T
A
= +25°C
0.01
0.5
100
I
V
= V
nA
µA
µs
SHDN Input Bias Current
SHDN
SHDN
IN
= +85°C
= +25°C
0.01
0.2
1
Shutdown Supply Current
I
V = 0V
OUT
Q, SHDN
= +85°C
= +25°C
30
150
300
Shutdown Exit Delay
(Note 3)
C
C
= 0.1µF,
= 1µF, no load
BP
OUT
= -40°C to +85°C
Shutdown Discharge
Resistance
MAX8868 only
300
2
_______________________________________________________________________________________
Low-Noise, Low-Dropout,
150mA Linear Regulators in SOT23
ELECTRICAL CHARACTERISTICS (continued)
(V = V
+ 0.5V, T = -40°C to +85°C, unless otherwise noted. Typical values are at T = +25°C.) (Note 1)
IN
OUT(NOMINAL)
A
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
THERMAL PROTECTION
Thermal Shutdown
Temperature
T
155
15
°C
°C
SHDN
Thermal Shutdown
Hysteresis
T
SHDN
Note 1: Limits are 100% production tested at T = +25°C. Limits over the operating temperature range are guaranteed through
A
correlation using Statistical Quality Control (SQC) Methods.
Note 2: The dropout voltage is defined as V - V
, when V
is 100mV below the value of V
for V = V
+ 0.5V.
IN
OUT
OUT
OUT
IN
OUT
Note 3: Time needed for V
to reach 95% of final value.
OUT
__________________________________________Typical Operating Characteristics
(V = V
IN
+ 0.5V, C = 1µF, C
= 1µF, C = 0.01µF, T = +25°C, unless otherwise noted.)
OUT(NOMINAL)
IN
OUT
BP
A
MAX886_EUK25
OUTPUT VOLTAGE vs. LOAD CURRENT
MAX886_EUK50
OUTPUT VOLTAGE vs. LOAD CURRENT
GROUND PIN CURRENT
vs. LOAD CURRENT
2.60
2.55
2.50
5.2
5.1
5.0
110
105
100
95
MAX886_EUK50
MAX886_EUK25
90
85
80
75
2.45
2.40
4.9
4.8
70
65
60
0
50
100
150
0
50
100
150
0
50
100
150
LOAD CURRENT (mA)
LOAD CURRENT (mA)
LOAD CURRENT (mA)
MAX886_EUK50
GROUND PIN CURRENT vs. INPUT VOLTAGE
MAX886_EUK25
GROUND PIN CURRENT vs. INPUT VOLTAGE
OUTPUT VOLTAGE vs. INPUT VOLTAGE
120
100
6
5
120
100
I
= 50mA
I
= 50mA
LOAD
LOAD
MAX886_EUK50
80
60
40
20
0
4
3
2
1
0
80
60
40
20
0
NO LOAD
NO LOAD
MAX886_EUK25
0
1
2
3
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
5
6
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
_______________________________________________________________________________________
3
Low-Noise, Low-Dropout,
150mA Linear Regulators in SOT23
____________________________Typical Operating Characteristics (continued)
(V = V
+ 0.5V, C = 1µF, C
= 1µF, C = 0.01µF, T = +25°C, unless otherwise noted.)
IN
OUT(NOMINAL)
IN
OUT
BP
A
MAX886_EUK25
OUTPUT VOLTAGE vs. TEMPERATURE
MAX886_EUK50
OUTPUT VOLTAGE vs. TEMPERATURE
GROUND PIN CURRENT vs. TEMPERATURE
200
180
160
140
120
100
80
2.60
2.55
5.20
I
= 50mA
LOAD
I
= 50mA
I
= 50mA
LOAD
LOAD
5.10
5.00
4.90
4.80
MAX886_EUK50
MAX886_EUK25
2.50
2.45
2.40
60
40
20
0
-40 -20
0
20
40
60
80
100
-40 -20
0
20
40
60
80
100
-40 -20
0
20
40
60
80
100
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
MAX886_EUK25
DROPOUT VOLTAGE vs. LOAD CURRENT
MAX886_EUK50
DROPOUT VOLTAGE vs. LOAD CURRENT
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY
70
60
50
40
30
20
10
0
250
200
150
100
50
200
150
T
A
= +85°C
C
OUT
= 10 F
T
A
= +85°C
T
A
= +25°C
C
OUT
= 1 F
100
50
0
T
A
= +25°C
T
A
= -40°C
T
A
= -40°C
I
= 50mA
= 0.1 F
LOAD
C
BP
0
0
20 40 60 80 100 120 140 160
LOAD CURRENT (mA)
0
20 40 60 80 100 120 140 160
LOAD CURRENT (mA)
0.01
0.1
1
10
100
1000
FREQUENCY (kHz)
OUTPUT NOISE SPECTRAL DENSITY
vs. FREQUENCY
OUTPUT NOISE vs. BP CAPACITANCE
OUTPUT NOISE vs. LOAD CURRENT
80
70
60
10
1
C
C
= 10 F
OUT
C
LOAD
= 10 F
= 10mA
OUT
C
LOAD
= 0.01 F
BP
= 0.01 F
BP
I
I
= 10mA
50
f = 10Hz TO 100kHz
f = 10Hz TO 100kHz
MAX886_EUK50
60
50
40
30
20
40
30
20
MAX886_EUK50
MAX886_EUK30
MAX886_EUK30
C
OUT
= 1 F
0.1
0.01
MAX886_EUK25
MAX886_EUK25
10
0
C
OUT
= 10 F
10
0
0.001
0.01
BP CAPACITANCE ( F)
0.1
1
10
100
0.1
1
10
FREQUENCY (kHz)
100
1000
LOAD CURRENT (mA)
4
_______________________________________________________________________________________
Low-Noise, Low-Dropout,
150mA Linear Regulators in SOT23
____________________________Typical Operating Characteristics (continued)
(V = V
IN
+ 0.5V, C = 1µF, C
= 1µF, C = 0.01µF, T = +25°C, unless otherwise noted.)
OUT BP A
OUT(NOMINAL)
IN
LOAD-TRANSIENT RESPONSE
NEAR DROPOUT
LOAD-TRANSIENT RESPONSE
LINE-TRANSIENT RESPONSE
MAX8867/8-19
MAX8867/8-18
MAX8867/8-20
3.01V
3.00V
2.99V
4V
3V
3.01V
V
IN
3.00V
2.99V
V
OUT
V
OUT
3.001V
2.999V
V
OUT
50mA
0mA
50mA
0mA
I
LOAD
I
LOAD
10 s/div
MAX886_EUK30, V = V + 0.5V,
100 s/div
= 50mA
10 s/div
MAX886_EUK30, V = V + 0.1V,
MAX886_EUK30, I
IN
OUT
LOAD
IN
OUT
C
= 10 F, I
= 0mA TO 50mA
IN
LOAD
C
= 10 F, I
= 0mA TO 50mA
IN
LOAD
MAX8868
ENTERING SHUTDOWN
MAX886_EUK50
SHUTDOWN EXIT DELAY
MAX886_EUK25
SHUTDOWN EXIT DELAY
MAX8867/8-25
MAX8867-23
MAX8867-21
2V
0V
V
V
V
SHDN
SHDN
V
2V
2V
0V
SHDN
C
= 0.01 F
C
BP
= 0.01 F
BP
0V
V
OUT
4V
2V
1V
0V
OUT
C
BP
= 0.1 F
V
OUT
C
= 0.1 F
BP
2V
0V
0V
500 s/div
5 s/div
5 s/div
NO LOAD
I
= 50mA
I
= 50mA
LOAD
LOAD
MAX886_EUK25
10Hz TO 100kHz OUTPUT NOISE
REGION OF STABLE C
ESR
OUT
vs. LOAD CURRENT
100
10
1
C
OUT
= 1 F
C
V
OUT
= 10 F
50 V/div
OUT
STABLE REGION
0.1
0.01
1ms/div
0
20
40
60
80 100 120 140
C
OUT
= 10 F, C = 0.1 F, I
= 10mA
BP
LOAD
LOAD CURRENT (mA)
_______________________________________________________________________________________
5
Low-Noise, Low-Dropout,
150mA Linear Regulators in SOT23
______________________________________________________________Pin Description
PIN
NAME
FUNCTION
Active-Low Shutdown Input. A logic low reduces the supply current to 10nA. On the MAX8868, a logic low
also causes the output voltage to discharge to GND. Connect to IN for normal operation.
1
SHDN
Ground. This pin also functions as a heatsink. Solder to a large pad or the circuit-board ground plane to
maximize power dissipation.
2
GND
Regulator Input. Supply voltage can range from 2.5V to 6.5V. Bypass with a 1µF capacitor to GND (see
Capacitor Selection and Regulator Stability section).
3
4
5
IN
OUT
BP
Regulator Output. Sources up to 150mA. Bypass with a 1µF (<0.2 typical ESR) capacitor to GND.
Reference-Noise Bypass. Bypass with a low-leakage, 0.01µF ceramic capacitor for reduced noise at the
output.
REVERSE
BATTERY
PROTECTION
IN
SHDN
MOS DRIVER
WITH I
LIMIT
P
ERROR
AMP
SHUTDOWN
AND POWER-ON
CONTROL
MAX8867
MAX8868
OUT
N
*
1.25V
REF
THERMAL
SENSOR
GND
* AUTO-DISCHARGE, MAX8868 ONLY
BP
Figure 1. Functional Diagram
The 1.25V bandgap reference is connected to the error
amplifier’s inverting input. The error amplifier compares
this reference with the feedback voltage and amplifies
the difference. If the feedback voltage is lower than the
reference voltage, the pass-transistor gate is pulled
lower, which allows more current to pass to the output
and increases the output voltage. If the feedback volt-
age is too high, the pass-transistor gate is pulled up,
allowing less current to pass to the output. The output
voltage is fed back through an internal resistor voltage
divider connected to the OUT pin.
_______________Detailed Description
The MAX8867/MAX8868 are low-noise, low-dropout,
low-quiescent-current linear regulators designed pri-
marily for battery-powered applications. The parts are
available with preset output voltages varying from 2.5V
to 5.0V in 100mV increments. These devices can sup-
ply loads up to 150mA. As illustrated in Figure 1, the
MAX8867/MAX8868 consist of a 1.25V reference, error
amplifier, P-channel pass transistor, and internal feed-
back voltage divider.
6
_______________________________________________________________________________________
Low-Noise, Low-Dropout,
150mA Linear Regulators in SOT23
An external bypass capacitor connected to the BP pin
Operating Region and Power Dissipation
The MAX8867/MAX8868’s maximum power dissipation
depends on the thermal resistance of the case and cir-
cuit board, the temperature difference between the die
junction and ambient air, and the rate of air flow. The
reduces noise at the output. Additional blocks include a
current limiter, reverse battery protection, thermal sen-
sor, and shutdown logic. The MAX8868 also includes
an auto-discharge function, which actively discharges
the output voltage to ground when the device is placed
in shutdown mode.
power dissipation across the device is P = I
(V
-
OUT
IN
V
). The maximum power dissipation is:
OUT
P
= (T - T ) / (
+
)
BA
MAX
J
A
JB
Output Voltage
The MAX8867/MAX8868 are supplied with factory-set
output voltages from 2.5V to 5V, in 100mV increments.
Except for the MAX886_EUK29 and the MAX886_EUK32
(which have an output voltage preset at 2.84V and
3.15V, respectively), the two-digit suffix allows the cus-
tomer to choose the output voltage in 100mV increments.
For example, the MAX8867EUK33 has a preset output
voltage of 3.3V. (see Expanded Ordering Information).
where T - T is the temperature difference between the
J
A
MAX8867/MAX8868 die junction and the surrounding
air,
(or
age, and
) is the thermal resistance of the pack-
is the thermal resistance through the
JB
JC
BA
printed circuit board, copper traces, and other materi-
als to the surrounding air.
The GND pin of the MAX8867/MAX8868 performs the
dual function of providing an electrical connection to
ground and channeling heat away. Connect the GND
pin to ground using a large pad or ground plane.
Internal P-Channel Pass Transistor
The MAX8867/MAX8868 feature a 1.1 typical P-chan-
nel MOSFET pass transistor. This provides several
advantages over similar designs using PNP pass tran-
sistors, including longer battery life. The P-channel
MOSFET requires no base drive, which reduces quies-
cent current considerably. PNP-based regulators waste
considerable current in dropout when the pass transis-
tor saturates. They also use high base-drive currents
under large loads. The MAX8867/MAX8868 do not suf-
fer from these problems and consume only 100µA of
quiescent current whether in dropout, light-load, or
heavy-load applications (see the Typical Operating
Characteristics).
Reverse Battery Protection
The MAX8867/MAX8868 have a unique protection
scheme that limits the reverse supply current to 1mA
when either V or V
falls below ground. Their cir-
SHDN
IN
cuitry monitors the polarity of these two pins and dis-
connects the internal circuitry and parasitic diodes
when the battery is reversed. This feature prevents
device damage.
Noise Reduction
An external 0.01µF bypass capacitor at BP, in conjunction
with an internal 200k resistor, creates an 80Hz lowpass
filter for noise reduction. The MAX8867/MAX8868 exhibit
of output voltage noise with C
= 10µF. Start-up time is minimized by a
power-on circuit that pre-charges the bypass capacitor.
The Typical Operating Characteristics show graphs of
Noise vs. BP Capacitance, Noise vs. Load Current, and
Output Noise Spectral Density.
Current Limit
The MAX8867/MAX8868 include a current limiter, which
monitors and controls the pass transistor’s gate voltage,
limiting the output current to 390mA. For design purposes,
consider the current limit to be 160mA minimum to 500mA
maximum. The output can be shorted to ground for an
indefinite amount of time without damaging the part.
30µV
and C
= 0.01µF
BP
RMS
OUT
__________Applications Information
Thermal-Overload Protection
Thermal-overload protection limits total power dissipa-
tion in the MAX8867/MAX8868. When the junction tem-
Capacitor Selection and Regulator Stability
Normally, use a 1µF capacitor on the MAX8867/
MAX8868’s input and a 1µF to 10µF capacitor on the
output. Larger input capacitor values and lower ESRs
provide better supply-noise rejection and line-transient
response. Reduce noise and improve load-transient
response, stability, and power-supply rejection by
using large output capacitors. For stable operation over
the full temperature range and with load currents up to
150mA, a minimum of 1µF is recommended. Note that
some ceramic dielectrics exhibit large capacitance and
ESR variation with temperature. With dielectrics such as
perature exceeds T = +170°C, the thermal sensor
J
signals the shutdown logic, turning off the pass transis-
tor and allowing the IC to cool. The thermal sensor will
turn the pass transistor on again after the IC’s junction
temperature cools by 20°C, resulting in a pulsed output
during continuous thermal-overload conditions.
Thermal-overload protection is designed to protect the
MAX8867/MAX8868 in the event of fault conditions. For
continual operation, do not exceed the absolute maxi-
mum junction-temperature rating of T = +150°C.
J
_______________________________________________________________________________________
7
Low-Noise, Low-Dropout,
150mA Linear Regulators in SOT23
Z5U and Y5V, it may be necessary to use 2.2µF or
more to ensure stability at temperatures below -10°C.
With X7R or X5R dielectrics, 1µF should be sufficient at
all operating temperatures. Also, for high-ESR tantalum
capacitors, 2.2µF or more may be needed to maintain
ESR in the stable region. A graph of the Region of
When operating from sources other than batteries,
improved supply-noise rejection and transient response
can be achieved by increasing the values of the input
and output bypass capacitors, and through passive filter-
ing techniques. The Typical Operating Characteristics
show the MAX8867/MAX8868’s line- and load-transient
responses.
Stable C
ESR vs. Load Current is shown in the
OUT
Typical Operating Characteristics.
Load-Transient Considerations
The MAX8867/MAX8868 load-transient response
graphs (see Typical Operating Characteristics) show
two components of the output response: a DC shift from
the output impedance due to the load current change,
and the transient response. A typical transient for a
step change in the load current from 0mA to 50mA is
12mV. Increasing the output capacitor’s value and
decreasing the ESR attenuates the overshoot.
Use a 0.01µF bypass capacitor at BP for low output volt-
age noise. Increasing the capacitance will slightly
decrease the output noise, but increase the start-up time.
Values above 0.1µF provide no performance advantage
and are not recommended (see Shutdown Exit Delay
graph in the Typical Operating Characteristics).
PSRR and Operation from
Sources Other than Batteries
The MAX8867/MAX8868 are designed to deliver low
dropout voltages and low quiescent currents in battery-
powered systems. Power-supply rejection is 63dB at
low frequencies and rolls off above 10kHz. See the
Power-Supply Rejection Ratio Frequency graph in the
Typical Operating Characteristics.
Input-Output (Dropout) Voltage
A regulator’s minimum input-output voltage differential
(or dropout voltage) determines the lowest usable sup-
ply voltage. In battery-powered systems, this will deter-
mine the useful end-of-life battery voltage. Because the
MAX8867/MAX8868 use a P-channel MOSFET pass
transistor, their dropout voltage is a function of drain-to-
source on-resistance (R
) multiplied by the load
DS(ON)
current (see Typical Operating Characteristics).
Chip Information
TRANSISTOR COUNT: 247
SUBSTRATE CONNECTED TO GND
8
_______________________________________________________________________________________
Low-Noise, Low-Dropout,
150mA Linear Regulators in SOT23
________________________________________________________Package Information
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 _____________________ 9
© 2001 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
相关型号:
MAX8867EUK29
Fixed Positive LDO Regulator, 2.9V, 0.12V Dropout, CMOS, PDSO5, MO-178, SOT-23, 5 PIN
MAXIM
©2020 ICPDF网 联系我们和版权申明