MAX9940EVKIT [MAXIM]
Proven PCB Layout;
| 型号： | MAX9940EVKIT |
| 厂家： | 
MAXIM INTEGRATED PRODUCTS |
| 描述： | Proven PCB Layout PC |
| 文件： | 总5页 (文件大小：199K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
19-4520; Rev 0; 3/09
MAX9940 Evaluation Kit
Evluates:MAX940
General Description
Features
®
The MAX9940 evaluation kit (EV kit) is an assembled
and tested PCB used to evaluate the MAX9940 high-
voltage signal-line protector for microcontroller ports.
The MAX9940 EV kit demonstrates that microcontroller
ports are protected against high-voltage faults.
o Output Connection to 1-Wire Device (DS2413)
o Pushbutton that Initiates High-Voltage Fault
o Lead(Pb)-Free and RoHS Compliant
o Proven PCB Layout
The EV kit comes with a MAX9940AXK+ installed.
o Fully Assembled and Tested
Ordering Information
PART
TYPE
MAX9940EVKIT+
EV Kit
+Denotes lead(Pb)-free and RoHS compliant.
Component List
DESIGNATION QTY
DESCRIPTION
DESIGNATION QTY
DESCRIPTION
10μF 10%, 16V X5R ceramic
capacitors (0805)
KEMET C0805C106K4PACTU
R2, R3
2
1
0
3
220ꢀ 5% resistors (0603)
C1, C7, C9
C2, C3, C4
C8
3
3
1
2
R4
R5
3kꢀ 5% resistor (0603)
Not installed, resistor (0603)
Pushbutton switches
0.1μF 10%, 16V X7R ceramic
capacitors (0603)
TDK C1608X7R1C104K
SW1, SW2, SW3
High-voltage signal-line protector
(5 SC70)
Maxim MAX9940AXK+
U1
1
1μF 10%, 16V X5R ceramic
capacitor (0603)
TDK C1608X5R1C105K
Microcontroller (68 QFN-EP*)
Maxim MAXQ2000-RAX+
U2
U3
U4
1
1
1
10pF 5%, 50V C0G ceramic
capacitors (0603)
Murata GRM1885C1H100J
C5, C6
LDO regulator (5 SC70)
Maxim MAX8511EXK25+
D1
1
3
Green LED (0603)
Red LEDs (0603)
Addressable switch (6 TSOC)
Maxim DS2413P+
D2, D3, D4
Not installed, Schottky diode
(3 SOT23)
Fairchild BAT54C
16MHz crystal
Hong Kong X’tals
SSM1600000E18FAF
D5
0
Y1
1
—
—
1
1
Shunt
Not installed, 2 x 5-pin JTAG
header
H1
0
PCB: MAX9940 Evaluation Kit+
JU1
R1
1
1
3-pin header
*EP = Exposed pad.
2kꢀ 5% resistor (0603)
Component Suppliers
SUPPLIER
PHONE
WEBSITE
Hong Kong X’tals Ltd.
KEMET Corp.
852-35112388
864-963-6300
770-436-1300
847-803-6100
www.hongkongcrystal.com
www.kemet.com
Murata Electronics North America, Inc.
TDK Corp.
www.murata-northamerica.com
www.component.tdk.com
Note: Indicate that you are using the MAX9940 when contacting these component suppliers.
1-Wire is a registered trademark of Maxim Integrated Products, Inc.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX9940 Evaluation Kit
Quick Start
Recommended Equipment
Detailed Description of Hardware
The MAX9940 EV kit is an assembled and tested PCB
used to evaluate the MAX9940 high-voltage signal-line
protector for microcontroller ports. The MAX9940 EV kit
demonstrates that microcontroller ports are protected
against high-voltage faults.
• 3.3V DC power supply
• 28V DC power supply
Procedure
The MAX9940 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on power supplies until all
connections are completed.
START Pushbutton
Press the START pushbutton (SW2) to start communicat-
ing with the DS2413, dual-channel addressable switch.
The on-board microcontroller commands the DS2413 to
continuously blink the green LED for 30 cycles.
1) Connect the 3.3V DC power supply to the VCC and
GND pads on the EV kit.
STOP Pushbutton
Press the STOP pushbutton (SW3) to stop communicat-
ing with the DS2413. The green LED should stop blink-
ing if the STOP pushbutton is pressed. If JU1 is in the
2-3 position, then the MAX9940 is also disabled.
2) Connect the 28V DC power supply to the FAULT
and GND pads on the EV kit.
3) Verify that a shunt is installed in the 1-2 position on
jumper JU1.
4) Turn on both supplies.
FAULT Pushbutton
Press the FAULT pushbutton (SW1) while the microcon-
troller is communicating with the DS2413. The red LEDs
indicate that a voltage is applied to the EXT pin of the
MAX9940.
5) Press the START pushbutton (SW2) momentarily
and observe as the green LED (D1) continuously
turns on and off every 500ms for 30 cycles.
Evluates:MAX940
6) While the green LED is still blinking, press the
FAULT pushbutton (SW1) and observe as the red
LEDs (D2, D3, and D4) turn on. Once SW1 is deac-
tivated, the red LEDs turn off and the green LED
continues blinking until it reaches the end of its
sequence.
The absolute maximum voltage of the DATA signal of the
microcontroller (U2) is specified to be (V
i.e., 3.8V.
+ 0.5)V,
DDIO
When the MAX9940 detects a voltage greater than
(V + 0.3)V, it automatically turns off, presenting the
CC
high voltage fault signal on its EXT pin from appearing
on the DATA signal line, thus protecting the microcon-
troller from damage.
Table 1. VCC Selection (JU1)
SHUNT
POSITION
DESCRIPTION
1-2*
Connects the MAX9940 to the +3.3V supply. Before changing shunt positions, press the STOP pushbutton (SW3).
Enables the MAX9940 using the MAXQ2000’s GPIO pin, which is used for power saving. Power is only applied when
the START pushbutton (SW2) is pressed. Power is disabled when the MAXQ2000 is done communicating with the
DS2413. Before changing shunt positions, press the STOP pushbutton (SW3). Note: The MAX9940 can withstand
2-3
fault voltages even when its V = 0.
CC
*Default position.
2
_______________________________________________________________________________________
MAX9940 Evaluation Kit
Evluates:MAX940
Figure 1a. MAX9940 EV Kit Schematic (Sheet 1 of 2)
_______________________________________________________________________________________
3
MAX9940 Evaluation Kit
Evluates:MAX940
Figure 1b. MAX9940 EV Kit Schematic (Sheet 2 of 2)
4
_______________________________________________________________________________________
MAX9940 Evaluation Kit
Evluates:MAX940
Figure 2. MAX9940 EV Kit Component Placement Guide—
Component Side
Figure 3. MAX9940 EV Kit PCB Layout—Component Side
Figure 4. MAX9940 EV Kit PCB Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 _____________________ 5
© 2009 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
相关型号：
MAX9943AUA+T
Operational Amplifier, 1 Func, 240uV Offset-Max, BICMOS, PDSO8, ROHS COMPLIANT, MO-187AA, USOP-8
MAXIM
©2020 ICPDF网 联系我们和版权申明