MCP3427-ESL [MAXIM]
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference; 16位,多通道模拟数字转换器,带有I2C接口,并板载参考型号: | MCP3427-ESL |
厂家: | MAXIM INTEGRATED PRODUCTS |
描述: | 16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference |
文件: | 总56页 (文件大小:944K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MCP3426/7/8
16-Bit, Multi-Channel ΔΣ Analog-to-Digital Converter with
I2C™ Interface and On-Board Reference
Features
Description
• 16-bit ΔΣ ADC with Differential Inputs:
- 2 channels: MCP3426 and MCP3427
- 4 channels: MCP3428
The MCP3426, MCP3427 and MCP3428 devices
(MCP3426/7/8) are the low noise and high accuracy
16 Bit Delta-Sigma Analog-to-Digital (ΔΣ A/D) Con-
verter family members of the MCP342X series from
Microchip Technology Inc. These devices can convert
analog inputs to digital codes with up to 16 bits of reso-
lution.
• Differential Input Full Scale Range: -VREF to
+VREF
• Self Calibration of Internal Offset and Gain per
Each Conversion
The MCP3426 and MCP3427 devices have two
differential input channels and the MCP3428 has four
differential input channels. All electrical properties of
these three devices are the same except the
differences in the number of input channels and I2C
address bit selection options.
• On-Board Voltage Reference (VREF):
- Accuracy: 2.048V ± 0.05%
- Drift: 15 ppm/°C
• On-Board Programmable Gain Amplifier (PGA):
- Gains of 1,2, 4 or 8
These devices can output analog-to-digital conversion
results at rates of 15 (16-bit mode), 60 (14-bit mode), or
240 (12-bit mode) samples per second depending on
the user controllable configuration bit settings using the
two-wire I2C serial interface. During each conversion,
the device calibrates offset and gain errors
automatically. This provides accurate conversion
results from conversion to conversion over variations in
temperature and power supply fluctuation.
• INL: 10 ppm of Full Scale Range
• Programmable Data Rate Options:
- 15 SPS (16 bits)
- 60 SPS (14 bits)
- 240 SPS (12 bits)
• One-Shot or Continuous Conversion Options
• Low Current Consumption (VDD= 3V):
- Continuous Conversion: 135 µA typical
The device has an on-board 2.048V reference voltage,
which enables an input range of ± 2.048V differentially
(full scale range = 4.096/PGA).
- One-Shot Conversion with 1 SPS:
- 9 µA typical for 16 bit mode
- 2.25 µA typical for 14 bit mode
- 0.56 µA typical for 12 bit mode
The user can select the gain of the on-board
programmable gain amplifier (PGA) using the
configuration register bits (gain of x1, x2, x4, or x8).
This allows the MCP3426/7/8 devices to convert a very
weak input signal with high resolution.
• On-Board Oscillator
• I2C™ Interface:
- Standard, Fast and High Speed Modes
- User configurable two external address
selection pins for MCP3427 and MCP3428
The MCP3426/7/8 devices have two conversion
modes: (a) One-Shot Conversion mode and
(b) Continuous Conversion mode. In the One-Shot
conversion mode, the device performs a single
• Single Supply Operation: 2.7V to 5.5V
• Extended Temperature Range: -40°C to +125°C
conversion and enters
a
low current standby
Typical Applications
(shutdown) mode automatically until it receives another
conversion command. This reduces current
consumption greatly during idle periods. In continuous
conversion mode, the conversion takes place
continuously at the configured conversion speed. The
device updates its output buffer with the most recent
conversion data.
• Portable Instrumentation and Consumer Goods
• Temperature Sensing with RTD, Thermistor, and
Thermocouple
• Bridge Sensing for Pressure, Strain, and Force
• Weigh Scales and Battery Fuel Gauges
• Factory Automation Equipment
The devices operate from a single 2.7V to 5.5V power
supply and have a two-wire I2C compatible serial
interface for a standard (100 kHz), fast (400 kHz), or
high-speed (3.4 MHz) mode.
© 2009 Microchip Technology Inc.
DS22226A-page 1
MCP3426/7/8
The I2C address bits for the MCP3427 and MCP3428
are selected by using two external I2C address
selection pins (Adr0 and Adr1). The user can configure
the device to one of eight available addresses by
The MCP3426 is available in 8-pin SOIC, DFN, and
MSOP packages. The MCP3427 is available in 10-pin
DFN, and MSOP packages. The MCP3428 is available
in 14-pin SOIC and TSSOP packages.
connecting these two address selection pins to VDD
V
,
SS or float. The I2C address bits of the MCP3426 are
programmed at the factory during production.
Package Types
MSOP, SOIC
MSOP
SOIC, TSSOP
14
CH1+
CH1-
1
2
3
4
5
6
7
CH1+
CH4-
10
9
Adr1
1
2
3
4
5
CH1+
CH1-
8
CH2-
1
CH1-
13
12
Adr0
SCL
SDA
CH4+
CH3-
7
6
5
CH2+
2
3
4
8
V
SS
CH2+
CH2-
V
V
DD
SS
CH2+
CH2-
7
6
SCL
11
10
SDA
CH3+
Adr1
V
DD
V
SS
9
8
V
Adr0
SCL
DD
SDA
MCP3426
2x3 DFN *
MCP3427
3x3 DFN *
CH1+
CH1-
CH2-
CH1+
CH1-
Adr1
1
2
8
7
1
10
9
CH2+
Adr0
2
EP
9
EP
11
VDD
VSS
V
SCL
SDA
VDD
3
4
6
5
3
4
5
8
7
6
SS
SDA
SCL
CH2+
CH2-
* Includes Exposed Thermal Pad (EP); see Table 3-1.
MCP3426 Functional Block Diagram
VDD
VSS
Voltage Reference
(2.048V)
MCP3426
VREF
CH1+
SCL
SDA
I2C
Interface
ΔΣ ADC
Converter
CH1-
CH2+
CH2-
PGA
Gain = 1, 2, 4, or 8
Clock
Oscillator
DS22226A-page 2
© 2009 Microchip Technology Inc.
MCP3426/7/8
MCP3427 Functional Block Diagram
VDD
VSS
MCP3427
Adr1
Adr0
Voltage Reference
(2.048V)
VREF
CH1+
SCL
I2C
ΔΣ ADC
Converter
CH1-
PGA
Interface
SDA
CH2+
CH2-
Gain = 1, 2, 4, or 8
Clock
Oscillator
MCP3428 Functional Block Diagram
VDD
VSS
MCP3428
CH1+
Adr1
Adr0
Voltage Reference
(2.048V)
CH1-
VREF
CH2+
SCL
SDA
I2C
CH2-
ΔΣ ADC
Converter
PGA
Interface
CH3+
CH3-
Gain = 1, 2, 4, or 8
Clock
Oscillator
CH4+
CH4-
© 2009 Microchip Technology Inc.
DS22226A-page 3
MCP3426/7/8
NOTES:
DS22226A-page 4
© 2009 Microchip Technology Inc.
MCP3426/7/8
†Notice: Stresses above those listed under “Maximum Rat-
ings” may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied.
Exposure to maximum rating conditions for extended periods
may affect device reliability.
1.0
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings†
VDD...................................................................................7.0V
All inputs and outputs ............. ..........VSS –0.4V to VDD+0.4V
Differential Input Voltage ...................................... |VDD - VSS
|
Output Short Circuit Current ................................Continuous
Current at Input Pins ....................................................±2 mA
Current at Output and Supply Pins ............................±10 mA
Storage Temperature ....................................-65°C to +150°C
Ambient Temp. with power applied ...............-55°C to +125°C
ESD protection on all pins ................ ≥ 6 kV HBM, ≥ 400V MM
Maximum Junction Temperature (TJ)..........................+150°C
ELECTRICAL CHARACTERISTICS
Electrical Specifications: Unless otherwise specified, all parameters apply for TA = -40°C to +85°C, VDD = +5.0V, VSS = 0V,
CHn+ = CHn- = VREF/2, VINCOM = VREF /2. All ppm units use 2*VREF as differential full scale range.
Parameters
Analog Inputs
Sym
Min
Typ
Max
Units
Conditions
Differential Full Scale Input
Voltage Range
FSR
—
±2.048/PGA
—
V
VIN = [CHn+ - CHn-]
Maximum Input Voltage Range
Differential Input Impedance
VSS-0.3
—
—
VDD+0.3
—
V
(Note 1)
ZIND (f)
ZINC (f)
2.25/PGA
MΩ
During normal mode operation
(Note 2)
Common Mode input
Impedance
—
25
—
MΩ
PGA = 1, 2, 4, 8
System Performance
Resolution and No Missing
Codes
(Effective Number of Bits)
(Note 3)
12
14
16
—
—
—
—
—
—
Bits
Bits
Bits
DR = 240 SPS
DR = 60 SPS
DR = 15 SPS
Data Rate
(Note 4)
DR
176
44
11
240
60
328
82
SPS
SPS
SPS
12 bits mode
14 bits mode
16 bits mode
15
20.5
—
Output Noise
—
2.5
µVRMS TA = +25°C, DR =15 SPS,
PGA = 1, VIN+ = VIN- = GND
Integral Non-Linearity
INL
—
10
—
ppm of DR = 15 SPS
FSR
(Note 5)
Internal Reference Voltage
Gain Error (Note 6)
VREF
—
—
—
—
2.048
0.1
—
—
—
—
V
%
PGA = 1, DR = 15 SPS
PGA Gain Error Match (Note 6)
Gain Error Drift (Note 6)
0.1
%
Between any 2 PGA settings
15
ppm/°C PGA=1, DR=15 SPS
Note 1: Any input voltage below or greater than this voltage causes leakage current through the ESD diodes at the input pins.
This parameter is ensured by characterization and not 100% tested.
2: This input impedance is due to 3.2 pF internal input sampling capacitor.
3: This parameter is ensured by design and not 100% tested.
4: The total conversion speed includes auto-calibration of offset and gain.
5: INL is the difference between the endpoints line and the measured code at the center of the quantization band.
6: Includes all errors from on-board PGA and VREF
.
7: This parameter is ensured by characterization and not 100% tested.
8: MCP3427 and MCP3428 only.
9: Addr_Float voltage is applied at address pin.
10: No voltage is applied at address pin (left “floating”).
© 2009 Microchip Technology Inc.
DS22226A-page 5
MCP3426/7/8
ELECTRICAL CHARACTERISTICS (CONTINUED)
Electrical Specifications: Unless otherwise specified, all parameters apply for TA = -40°C to +85°C, VDD = +5.0V, VSS = 0V,
CHn+ = CHn- = VREF/2, VINCOM = VREF /2. All ppm units use 2*VREF as differential full scale range.
Parameters
Offset Error
Sym
Min
Typ
Max
Units
Conditions
VOS
—
30
—
µV
PGA = 1
DR = 15 SPS
Offset Drift vs. Temperature
Common-Mode Rejection
—
—
—
—
50
105
110
5
—
—
—
—
nV/°C
dB
at DC and PGA =1,
dB
at DC and PGA =8, TA = +25°C
Gain vs. VDD
ppm/V TA = +25°C, VDD = 2.7V to 5.5V,
PGA = 1
Power Supply Rejection at DC
Input
—
100
—
dB
TA = +25°C, VDD = 2.7V to 5.5V,
PGA = 1
Power Requirements
Voltage Range
VDD
IDDA
2.7
—
—
—
—
5.5
180
—
V
Supply Current during
Conversion
145
135
0.3
µA
µA
µA
VDD = 5.0V
VDD = 3.0V
VDD = 5.0V
Supply Current during Standby
Mode
IDDS
1
I2C Digital Inputs and Digital Outputs
High level input voltage
Low level input voltage
Low level output voltage
VIH
0.7VDD
—
—
—
—
—
VDD
0.3VDD
0.4
V
V
V
V
at SDA and SCL pins
at SDA and SCL pins
IOL = 3 mA
VIL
VOL
—
Hysteresis of Schmidt Trigger
VHYST
0.05VDD
—
fSCL = 100 kHz
for inputs (Note 7)
Supply Current when I2C bus
line is active
IDDB
—
—
10
µA
Device is in standby mode while
I2C bus is active
Input Leakage Current
IILH
IILL
Logic Status of I2C Address Pins (Note 8)
—
-1
—
—
1
µA
µA
VIH = 5.5V
VIL = GND
—
Adr0 and Adr1 Pins
Adr0 and Adr1 Pins
Adr0 and Adr1 Pins
Addr_Low
VSS
—
—
—
0.2VDD
VDD
V
V
V
The device reads logic low.
The device reads logic high.
Addr_High 0.75VDD
Addr_Float 0.35VDD
0.6VDD
Read pin voltage if voltage is
applied to the address pin.
(Note 9)
—
V
DD/2
—
Device outputs float output
voltage (VDD/2) on the address
pin, if left “floating”. (Note 10)
Pin Capacitance and I2C Bus Capacitance
Pin capacitance
I2C Bus Capacitance
CPIN
Cb
—
—
4
10
pF
pF
—
400
Note 1: Any input voltage below or greater than this voltage causes leakage current through the ESD diodes at the input pins.
This parameter is ensured by characterization and not 100% tested.
2: This input impedance is due to 3.2 pF internal input sampling capacitor.
3: This parameter is ensured by design and not 100% tested.
4: The total conversion speed includes auto-calibration of offset and gain.
5: INL is the difference between the endpoints line and the measured code at the center of the quantization band.
6: Includes all errors from on-board PGA and VREF
.
7: This parameter is ensured by characterization and not 100% tested.
8: MCP3427 and MCP3428 only.
9: Addr_Float voltage is applied at address pin.
10: No voltage is applied at address pin (left “floating”).
DS22226A-page 6
© 2009 Microchip Technology Inc.
MCP3426/7/8
TEMPERATURE CHARACTERISTICS
Electrical Specifications: Unless otherwise indicated, TA = -40°C to +125°C, VDD = +5.0V, VSS = 0V.
Parameters
Temperature Ranges
Sym
Min
Typ
Max
Units
Conditions
Specified Temperature Range
Operating Temperature Range
Storage Temperature Range
TA
TA
TA
-40
-40
-65
—
—
—
+85
+125
+150
°C
°C
°C
Thermal Package Resistances
Thermal Resistance, 8L-DFN (2x3)
Thermal Resistance, 8L-MSOP
Thermal Resistance, 8L-SOIC
Thermal Resistance, 10L-DFN (3x3)
Thermal Resistance, 10L-MSOP
Thermal Resistance, 14L-SOIC
Thermal Resistance, 14L-TSSOP
θJA
θJA
θJA
θJA
θJA
θJA
θJA
—
—
—
—
—
—
—
84.5
211
—
—
—
—
—
—
—
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
149.5
57
202
120
100
© 2009 Microchip Technology Inc.
DS22226A-page 7
MCP3426/7/8
NOTES:
DS22226A-page 8
© 2009 Microchip Technology Inc.
MCP3426/7/8
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
Note: Unless otherwise indicated, TA = -40°C to +85°C, VDD = +5.0V, VSS = 0V, CHn+ = CHn- = VREF/2,
VINCOM = VREF/2.
0.005
0.004
0.003
0.002
0.001
0
12
10
8
PGA = 1
PGA = 1
PGA = 2
6
PGA = 4
PGA = 8
4
PGA = 4
2
PGA = 2
3.5
PGA = 8
0
2.5
3
4
4.5
5
5.5
-100 -75 -50 -25
0
25
50
75 100
Input Signal (% of FSR)
V
DD (V)
FIGURE 2-1:
(V ).
INL vs. Supply Voltage
FIGURE 2-4:
Voltage.
Output Noise vs. Input
DD
0.005
2
1.5
1
TA = +25°C
PGA = 1
PGA = 8
0.004
0.003
0.002
0.001
0
0.5
0
2.7V
PGA = 4
-0.5
-1
PGA = 2
-1.5
-2
5V
-60 -40 -20
0
20 40 60 80 100 120 140
-100 -75 -50 -25
0
25
50
75 100
Temperature (oC)
Input Voltage (% of Full-Scale)
FIGURE 2-2:
INL vs. Temperature.
FIGURE 2-5:
Total Error vs. Input Voltage.
0.2
0.1
20
15
10
5
VDD = 5V
PGA = 8
PGA = 4
PGA = 8
0
PGA = 1
-0.1
-0.2
-0.3
-0.4
-0.5
-0.6
0
-5
-10
-15
PGA = 2
PGA = 2
PGA = 1
-20
-25
PGA = 4
-40 -20
0
20 40 60 80 100 120 140
Temperature (oC)
-60 -40 -20
0
20 40 60 80 100 120 140
Temperature (°C)
FIGURE 2-3:
Offset Error vs.
FIGURE 2-6:
Gain Error vs. Temperature.
Temperature.
© 2009 Microchip Technology Inc.
DS22226A-page 9
MCP3426/7/8
Note: Unless otherwise indicated, TA = -40°C to +85°C, VDD = +5.0V, VSS = 0V, CHn+ = CHn- = VREF/2,
VINCOM = VREF/2.
5
4
200
180
160
140
120
100
80
VDD = 5.5V
3
2
VDD = 2.7V
VDD = 2.7V
1
VDD = 5.0V
0
VDD = 5.0V
60
-1
-60 -40 -20
0
20 40 60 80 100 120 140
Temperature (°C)
-60 -40 -20
0
20 40 60 80 100 120 140
Temperature (°C)
FIGURE 2-7:
I
vs. Temperature.
FIGURE 2-10:
Oscillator Drift vs.
DDA
Temperature.
0
-10
-20
-30
-40
-50
-60
-70
-80
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Data Rate = 15 SPS
VDD = 5.5V
VDD = 5.0V
-90
-100
-110
-120
VDD = 2.7V
1k
10k
0.1
1
10
100
-60 -40 -20
0
20 40 60 80 100 120 140
Temperature (°C)
Input Signal Frequency (Hz)
FIGURE 2-8:
I
vs. Temperature.
FIGURE 2-11:
Frequency Response.
DDS
14
VDD = 5.5V
12
10
8
VDD = 5.0V
VDD = 4.5V
6
4
VDD = 2.7V
2
0
-60 -40 -20
0
20 40 60 80 100 120 140
Temperature (°C)
FIGURE 2-9:
I
vs. Temperature.
DDB
DS22226A-page 10
© 2009 Microchip Technology Inc.
MCP3426/7/8
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
MCP3426
PIN FUNCTION TABLE
MCP3427 MCP3428
Sym
Function
MSOP,
SOIC
SOIC,
TSSOP
DFN
DFN
MSOP
1
2
1
2
1
2
1
2
1
2
CH1+
CH1-
CH2+
CH2-
VSS
Positive Differential Analog Input Pin of Channel 1
Negative Differential Analog Input Pin of Channel 1
Positive Differential Analog Input Pin of Channel 2
Negative Differential Analog Input Pin of Channel 2
Ground Pin
7
7
4
4
3
8
8
5
5
4
6
6
3
3
5
3
3
6
6
6
VDD
Positive Supply Voltage Pin
4
4
7
7
7
SDA
SCL
Bidirectional Serial Data Pin of the I2C Interface
Serial Clock Pin of the I2C Interface
5
5
8
8
8
—
—
—
—
—
—
9
—
—
—
—
—
—
—
9
9
9
Adr0
Adr1
CH3+
CH3-
CH4+
CH4-
EP
I2C Address Selection Pin. See Section 5.3.2.
I2C Address Selection Pin. See Section 5.3.2.
Positive Differential Analog Input Pin of Channel 3
Negative Differential Analog Input Pin of Channel 3
Positive Differential Analog Input Pin of Channel 4
Negative Differential Analog Input Pin of Channel 4
10
—
—
—
—
11
10
—
—
—
—
—
10
11
12
13
14
—
Exposed Thermal Pad (EP); must be connected to
VSS
3.1
Analog Inputs (CHn+, CHn-)
3.2
Supply Voltage (VDD, VSS)
CHn+ and CHn- are differential input pins for
channel n. The user can also connect CHn- pin to VSS
for a single-ended operation. See Figure 6-4 for
differential and single-ended connection examples.
VDD is the power supply pin for the device. This pin
requires an appropriate bypass ceramic capacitor of
about 0.1 µF to ground to attenuate high frequency
noise presented in application circuit board. An
additional 10 µF capacitor (tantalum) in parallel is also
recommended to further attenuate current spike
noises. The supply voltage (VDD) must be maintained
in the 2.7V to 5.5V range for specified operation.
The maximum voltage range on each differential input
pin is from VSS-0.3V to VDD+0.3V. Any voltage below or
above this range will cause leakage currents through
the Electrostatic Discharge (ESD) diodes at the input
pins.
VSS is the ground pin and the current return path of the
device. The user must connect the VSS pin to a ground
plane through a low impedance connection. If an
analog ground path is available in the application PCB
(printed circuit board), it is highly recommended that
the VSS pin be tied to the analog ground path or
isolated within an analog ground plane of the circuit
board.
This ESD current can cause unexpected performance
of the device. The input voltage at the input pins should
be within the specified operating range defined in
Section 1.0 “Electrical Characteristics” and
Section 4.0 “Description of Device Operation”.
See Section 4.5 “Input Voltage Range” for more
details of the input voltage range.
Figure 3-1 shows the input structure of the device. The
device uses a switched capacitor input stage at the
front end. CPIN is the package pin capacitance and
typically about 4 pF. D1 and D2 are the ESD diodes.
CSAMPLE is the differential input sampling capacitor.
© 2009 Microchip Technology Inc.
DS22226A-page 11
MCP3426/7/8
VDD
D1
Sampling
Switch
VT = 0.6V
VT = 0.6V
RS
SS
CHn
RSS
ILEAKAGE
(~ ±1 nA)
CPIN
4 pF
CSAMPLE
(3.2 pF)
V
D2
VSS
LEGEND
V
Rss
CHn
CPIN
VT
=
=
=
=
=
Signal Source
ILEAKAGE
=
=
=
=
Leakage Current at Analog Pin
Sampling Switch
Source Impedance
Analog Input Pin
SS
Rs
CSAMPLE
D1, D2
Sampling Switch Resistor
Sample Capacitance
Input Pin Capacitance
Threshold Voltage
=
ESD Protection Diode
FIGURE 3-1:
Equivalent Analog Input Circuit.
3.3
Serial Clock Pin (SCL)
3.4
Serial Data Pin (SDA)
SCL is the serial clock pin of the I2C interface. The
device acts only as a slave and the SCL pin accepts
only external serial clocks. The input data from the
Master device is shifted into the SDA pin on the rising
edges of the SCL clock and output from the slave
device occurs at the falling edges of the SCL clock. The
SCL pin is an open-drain N-channel driver. Therefore,
it needs a pull-up resistor from the VDD line to the SCL
SDA is the serial data pin of the I2C interface. The SDA
pin is used for input and output data. In read mode, the
conversion result is read from the SDA pin (output). In
write mode, the device configuration bits are written
(input) though the SDA pin. The SDA pin is an
open-drain N-channel driver. Therefore, it needs a
pull-up resistor from the VDD line to the SDA pin.
Except for start and stop conditions, the data on the
SDA pin must be stable during the high period of the
clock. The high or low state of the SDA pin can only
change when the clock signal on the SCL pin is low.
Refer to Section 5.3 “I2C Serial Communications”
for more details on I2C Serial Interface communication.
pin.
Refer
to
Section 5.3
“I2C
Serial
Communications” for more details on I2C Serial
Interface communication.
The typical range of the pull-up resistor value for SCL
and SDA is from 5 kΩ to 10 kΩ for standard (100 kHz)
and fast (400 kHz) modes, and less than 1 kΩ for high
speed mode (3.4 MHz).
3.5
Exposed Thermal Pad (EP)
There is an internal electrical connection between the
Exposed Thermal Pad (EP) and the VSS pin; they must
be connected to the same potential on the Printed
Circuit Board (PCB).
DS22226A-page 12
© 2009 Microchip Technology Inc.
MCP3426/7/8
The threshold voltage is set at 2.2V with a tolerance of
approximately ±5%. If the supply voltage falls below
this threshold, the device will be held in a reset
condition. The typical hysteresis value is approximately
200 mV.
4.0
DESCRIPTION OF DEVICE
OPERATION
4.1
General Overview
The
MCP3426/7/8
devices
are
differential
The POR circuit is shut down during the low-power
standby mode. Once a power-up event has occurred,
multi-channel low-power, 16-Bit Delta-Sigma A/D
converters with an I2C serial interface. The devices
contain an input channel selection multiplexer (mux), a
programmable gain amplifier (PGA), an on-board
voltage reference (2.048V), and an internal oscillator.
the
device
requires
additional
delay
time
(approximately 300 µs) before a conversion takes
place. During this time, all internal analog circuitries are
settled before the first conversion occurs. Figure 4-1
illustrates the conditions for power-up and power-down
events under typical start-up conditions.
When the device powers up (POR is set), it
automatically resets the configuration bits to default
settings.
VDD
4.1.1
DEVICE DEFAULT SETTINGS ARE:
2.2V
2.0V
300 µS
• Conversion bit resolution: 12 bits (240 sps)
• Input channel: Channel 1
• PGA gain setting: x1
• Continuous conversion
Time
Once the device is powered-up, the user can
reprogram the configuration bits using I2C serial
interface any time. The configuration bits are stored in
the volatile memory.
Reset Start-up
Normal Operation
Reset
FIGURE 4-1:
POR Operation.
4.3
Internal Voltage Reference
4.1.2
USER SELECTABLE OPTIONS ARE:
The device contains an on-board 2.048V voltage
reference. This reference voltage is for internal use
only and not directly measurable. The specification of
the reference voltage is part of the device’s gain and
drift specifications. Therefore, there is no separate
specification for the on-board reference.
• Conversion bit resolution: 12, 14, or 16 bits
• Input channel selection: CH1, CH2, CH3, or CH4.
• PGA Gain selection: x1, x2, x4, or x8
• Continuous or one-shot conversion
In the Continuous Conversion mode, the device
converts the inputs continuously. While in the One-Shot
Conversion mode, the device converts the input one
time and stays in the low-power standby mode until it
receives another command for a new conversion.
During the standby mode, the device consumes less
than 1 µA maximum.
4.4
Analog Input Channels
The user can select the input channel using the
configuration register bits. Each channel can be used
for differential or single-ended input.
Each input channel has a switched capacitor input
structure. The internal sampling capacitor (3.2 pF for
PGA = 1) is charged and discharged to process a
conversion. The charging and discharging of the input
sampling capacitor creates dynamic input currents at
each input pin. The current is a function of the
differential input voltages, and inversely proportional to
the internal sampling capacitance, sampling frequency,
and PGA setting.
4.2
Power-On-Reset (POR)
The device contains an internal Power-On-Reset
(POR) circuit that monitors power supply voltage (VDD
during operation. This circuit ensures correct device
start-up at system power-up and power-down events.
)
The device resets all configuration register bits to
default settings as soon as the POR is set.
The POR has built-in hysteresis and a timer to give a
high degree of immunity to potential ripples and noises
on the power supply. A 0.1 µF decoupling capacitor
should be mounted as close as possible to the VDD pin
for additional transient immunity.
© 2009 Microchip Technology Inc.
DS22226A-page 13
MCP3426/7/8
Care must be taken in setting the input voltage ranges
so that the input voltage does not exceed the absolute
maximum input voltage range.
4.5
Input Voltage Range
The differential (VIN) and common mode voltage
(VINCOM) at the input pins without considering PGA
setting are defined by:
4.6
Input Impedance
The device uses a switched-capacitor input stage using
a 3.2 pF sampling capacitor. This capacitor is switched
(charged and discharged) at a rate of the sampling
frequency that is generated by on-board clock. The
differential input impedance varies with the PGA
settings. The typical differential input impedance during
a normal mode operation is given by:
VIN = (CHn+) – (CHn-)
(CHn+) + (CHn-)
VINCOM = -----------------------------------------------
2
Where:
n
=
nth input channel (n=1, 2, 3, or 4)
The input signal levels are amplified by the internal
programmable gain amplifier (PGA) at the front end of
the ΔΣ modulator.
ZIN(f) = 2.25 MΩ /PGA
Since the sampling capacitor is only switching to the
input pins during a conversion process, the above input
impedance is only valid during conversion periods. In a
low power standby mode, the above impedance is not
presented at the input pins. Therefore, only a leakage
current due to ESD diode is presented at the input pins.
The user needs to consider two conditions for the input
voltage range: (a) Differential input voltage range and
(b) Absolute maximum input voltage range.
4.5.1
DIFFERENTIAL INPUT VOLTAGE
RANGE
The conversion accuracy can be affected by the input
signal source impedance when any external circuit is
connected to the input pins. The source impedance
adds to the internal impedance and directly affects the
time required to charge the internal sampling capacitor.
Therefore, a large input source impedance connected
to the input pins can degrade the system performance,
such as offset, gain, and Integral Non-Linearity (INL)
errors. Ideally, the input source impedance should be
zero. This can be achievable by using an operational
amplifier with a closed-loop output impedance of tens
of ohms.
The device performs conversions using its internal
reference voltage (VREF = 2.048V). Therefore, the
absolute value of the differential input voltage (VIN),
with PGA setting is included, needs to be less than the
internal reference voltage. The device will output
saturated output codes (all 0s or all 1s except sign bit)
if the absolute value of the input voltage (VIN), with
PGA setting is included, is greater than the internal
reference voltage (VREF = 2.048V). The input full scale
voltage range is given by:
EQUATION 4-1:
4.7
Aliasing and Anti-aliasing Filter
–VREF ≤ (VIN • PGA) ≤ (VREF – 1LSB)
Aliasing occurs when the input signal contains
time-varying signal components with frequency greater
than half the sample rate. In the aliasing conditions, the
device can output unexpected output codes. For
applications that are operating in electrical noise
environments, the time-varying signal noise or high
frequency interference components can be easily
added to the input signals and cause aliasing. Although
the device has an internal first order sinc filter, the filter
response (Figure 2-11) may not give enough
attenuation to all aliasing signal components. To avoid
the aliasing, an external anti-aliasing filter, which can
be accomplished with a simple RC low-pass filter, is
typically used at the input pins. The low-pass filter cuts
off the high frequency noise components and provides
a band-limited input signal to the input pins.
Where:
VIN
=
=
CHn+ - CHn-
2.048V
VREF
If the input voltage level is greater than the above limit,
the user can use a voltage divider and bring down the
input level within the full scale range. See Figure 6-7 for
more details of the input voltage divider circuit.
4.5.2
ABSOLUTE MAXIMUM INPUT
VOLTAGE RANGE
The input voltage at each input pin must be less than
the following absolute maximum input voltage limits:
• Input voltage < VDD+0.3V
• Input voltage > VSS-0.3V
4.8
Self-Calibration
Any input voltage outside this range can turn on the
input ESD protection diodes, and result in input
leakage current, causing conversion errors, or
permanently damage the device.
The device performs a self-calibration of offset and
gain for each conversion. This provides reliable
conversion results from conversion-to-conversion over
variations in temperature as well as power supply
fluctuations.
DS22226A-page 14
© 2009 Microchip Technology Inc.
MCP3426/7/8
Table 4-1 shows the LSB size of each conversion rate
setting. The measured unknown input voltage is
obtained by multiplying the output codes with LSB. See
the following section for the input voltage calculation
using the output codes.
4.9
Digital Output Codes and
Conversion to Real Values
4.9.1
DIGITAL OUTPUT CODE FROM
DEVICE
The digital output code is proportional to the input
voltage and PGA settings. The output data format is a
binary two’s complement. With this code scheme, the
MSB can be considered a sign indicator. When the
MSB is a logic ‘0’, the input is positive. When the MSB
is a logic ‘1’, the input is negative. The following is an
example of the output code:
TABLE 4-1:
RESOLUTION SETTINGS VS.
LSB
Resolution Setting
12 bits
LSB
1 mV
14 bits
16 bits
250 µV
62.5 µV
(a) for a negative full scale input voltage: 100...000
Example: (CHn+ - CHn-) •PGA = -2.048V
(b) for a zero differential input voltage: 000...000
Example: (CHn+ - CHn-) = 0
TABLE 4-2: EXAMPLE OF OUTPUT CODE
FOR 16 BITS (NOTE 1, NOTE 2)
Input Voltage:
Digital Output Code
[CHn+ - CHn-] • PGA
(c) for a positive full scale input voltage: 011...111
Example: (CHn+ - CHn-) • PGA = 2.048V
≥ VREF
REF - 1 LSB
2 LSB
0111111111111111
0111111111111111
0000000000000010
0000000000000001
0000000000000000
1111111111111111
1111111111111110
1000000000000000
1000000000000000
The MSB (sign bit) is always transmitted first through
the I2C serial data line. The resolution for each
conversion is 16, 14, or 12 bits depending on the
conversion rate selection bit settings by the user.
V
1 LSB
0
The output codes will not roll-over even if the input
voltage exceeds the maximum input range. In this
case, the code will be locked at 0111...11 for all
voltages greater than (VREF - 1 LSB)/PGA and
1000...00 for voltages less than -VREF/PGA.
Table 4-2 shows an example of output codes of various
input levels for 16-bit conversion mode. Table 4-3
shows an example of minimum and maximum output
codes for each conversion rate option.
-1 LSB
-2 LSB
- VREF
< -VREF
Note 1: MSB is a sign indicator:
0: Positive input (CHn+ > CHn-)
1: Negative input (CHn+ < CHn-)
2: Output data format is binary two’s
The number of output code is given by:
complement.
EQUATION 4-2:
TABLE 4-3:
MINIMUM AND MAXIMUM
OUTPUT CODES (NOTE)
Number of Output Code =
(CHn+ – CHn-)
----------------------------------------
= (Maximum Code + 1) × PGA ×
2.048V
Resolution
Setting
Minimum Maximum
Data Rate
Where:
Code
Code
See Table 4-3 for Maximum Code
12
14
16
240 SPS
60 SPS
15 SPS
-2048
-8192
2047
8191
The LSB of the data conversion is given by:
-32768
32767
Note:
Maximum n-bit code = 2N-1 - 1
EQUATION 4-3:
Minimum n-bit code = -1 x 2N-1
2 × VREF
LSB = --------------------- = --------------------------
2 × 2.048V
2N 2N
Where:
N
=
Resolution, which is programmed in
the Configuration Register: 12, 14,
or 16.
© 2009 Microchip Technology Inc.
DS22226A-page 15
MCP3426/7/8
4.9.2
CONVERTING THE DEVICE
OUTPUT CODE TO INPUT SIGNAL
VOLTAGE
EQUATION 4-4:
CONVERTING OUTPUT
CODES TO INPUT
VOLTAGE
When the user gets the digital output codes from the
device as described in Section 4.9.1 “Digital output
code from device”, the next step is converting the
digital output codes to a measured input voltage.
Equation 4-4 shows an example of converting the
output codes to its corresponding input voltage.
If MSB = 0 (Positive Output Code):
Input Voltage = (Output Code) •
LSB
PGA
-----------
If MSB = 1 (Negative Output Code):
LSB
PGA
(2′s complement of Output Code)
-----------
•
Input Voltage =
If the sign indicator bit (MSB) is ‘0’, the input voltage
is obtained by multiplying the output code with the LSB
and divided by the PGA setting.
Where:
LSB
2’s complement
=
=
See Table 4-1
1’s complement + 1
If the sign indicator bit (MSB) is ‘1’, the output code
needs to be converted to two’s complement before
multiplied by LSB and divided by the PGA setting.
Table 4-4 shows an example of converting the device
output codes to input voltage.
TABLE 4-4:
EXAMPLE OF CONVERTING OUTPUT CODE TO VOLTAGE (WITH 16 BIT SETTING)
Input Voltage
[CHn+ - CHn-] • PGA]
Digital Output Code
MSB
Example of Converting Output Codes to Input Voltage
≥ VREF
0111111111111111
(214+213+212+211+210+29+28+27+26+25+24+23+22+21+20)x
LSB(62.5μV)/PGA = 2.048 (V) for PGA = 1
0
VREF - 1 LSB
2 LSB
0111111111111111
0000000000000010
0000000000000001
0000000000000000
1111111111111111
1111111111111110
1000000000000000
1000000000000000
(214+213+212+211+210+29+28+27+26+25+24+23+22+21+20)x
LSB(62.5μV)/PGA = 2.048 (V) for PGA = 1
(0+0+0+0+0+0+0+0+0+0+0+0+0+21+0)x LSB(62.5μV)/PGA
= 125 (μV) for PGA = 1
(0+0+0+0+0+0+0+0+0+0+0+0+0+0+20)x LSB(62.5μV)/PGA
= 62.5 (μV)for PGA = 1
0
0
0
0
1
1
1
1
1 LSB
0
(0+0+0+0+0+0+0+0+0+0+0+0+0+0+0)x LSB(62.5μV)/PGA
= 0 V (V) for PGA = 1
-(0+0+0+0+0+0+0+0+0+0+0+0+0+0+20)x LSB(62.5μV)/
PGA = - 62.5 (μV)for PGA = 1
-(0+0+0+0+0+0+0+0+0+0+0+0+0+21+0)x LSB(62.5μV)/
PGA = - 125 (μV)for PGA = 1
-(215+0+0+0+0+0+0+0+0+0+0+0+0+0+0) x LSB(62.5μV)/
PGA = - 2.048 (V) for PGA = 1
-(215+0+0+0+0+0+0+0+0+0+0+0+0+0+0) x LSB(62.5μV)/
-1 LSB
-2 LSB
- VREF
≤ -VREF
PGA = - 2.048 (V) for PGA = 1
Note:
MSB = sign bit (1: “-”, 0: “+”)
DS22226A-page 16
© 2009 Microchip Technology Inc.
MCP3426/7/8
5.1.2
ONE-SHOT CONVERSION MODE
(O/C BIT = 0)
5.0
5.1
USING THE DEVICES
Operating Modes
Once the One-Shot Conversion (single conversion)
Mode is selected, the device performs only one
conversion, updates the output data register, clears the
data ready flag (RDY = 0), and then enters a low power
standby mode. A new One-Shot Conversion is started
again when the device receives a new write command
with RDY = 1.
The user operates the device by setting up the device
configuration register using a write command (see
Figure 5-3) and reads the conversion data using a read
command (see Figure 5-4 ). The device operates in two
modes: (a) Continuous Conversion Mode or
(b) One-Shot Conversion Mode (single conversion).
This mode selection is made by setting the O/C bit in
the Configuration Register. Refer to Section 5.2
“Configuration Register” for more information.
• When writing configuration register:
- The RDY bit needs to be set to begin a new
conversion in one-shot mode.
• When reading conversion data:
5.1.1
CONTINUOUS CONVERSION
MODE (O/C BIT = 1)
- RDY bit = 0means the latest conversion
result is ready.
The device performs a Continuous Conversion if the
O/C bit is set to logic “high”. Once the conversion is
completed, RDY bit is toggled to ‘0’and the result is
placed at the output data register. The device
immediately begins another conversion and overwrites
the output data register with the most recent result.
The device clears the data ready flag (RDY bit = 0)
when the conversion is completed. The device sets the
ready flag bit (RDY bit = 1), if the latest conversion
result has been read by the Master.
- RDY bit = 1means the conversion result is
not updated since the last reading. A new
conversion is under processing and the RDY
bit will be cleared when the new conversion is
done.
This One-Shot Conversion Mode is highly
recommended for low power operating applications
where the conversion result is needed by request on
demand. During the low current standby mode, the
device consumes less than 1 µA maximum (or 300 nA
typical). For example, if the user collects 16-bit
• When writing configuration register:
- Setting RDY bit in continuous mode does not
affect anything.
conversion data once
a
second in One-Shot
Conversion mode, the device draws only about one-
fifteenth of the operating currents for the continuous
conversion mode. In this example, the device
• When reading conversion data:
- RDY bit = 0 means the latest conversion
result is ready.
consumes
approximately
9 µA
(135 µA
/
15 SPS = 9 µA), when the device performs only one
conversion per second (1 SPS) in 16-bit conversion
mode with 3V power supply.
- RDY bit = 1 means the conversion result is
not updated since the last reading. A new
conversion is under processing and the RDY
bit will be cleared when the new conversion
result is ready.
© 2009 Microchip Technology Inc.
DS22226A-page 17
MCP3426/7/8
The user can rewrite the configuration byte any time
during the device operation. Register 5-1 shows the
configuration register bits.
5.2
Configuration Register
The device has an 8-bit wide configuration register to
select for: input channel, conversion mode, conversion
rate, and PGA gain. This register allows the user to
change the operating condition of the device and check
the status of the device operation.
REGISTER 5-1:
CONFIGURATION REGISTER
R/W-1
RDY
R/W-0
C1
R/W-0
C0
R/W-1
O/C
1 *
R/W-0
S1
R/W-0
S0
R/W-0
G1
R/W-0
G0
1 *
0 *
0 *
0 *
0 *
0 *
0 *
bit 7
bit 0
* Default Configuration after Power-On Reset
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
‘1’ = Bit is set
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared x = Bit is unknown
bit 7
RDY: Ready Bit
This bit is the data ready flag. In read mode, this bit indicates if the output register has been updated
with a latest conversion result. In One-Shot Conversion mode, writing this bit to “1” initiates a new
conversion.
Reading RDY bit with the read command:
1= Output register has not been updated.
0= Output register has been updated with the latest conversion result.
Writing RDY bit with the write command:
Continuous Conversion mode: No effect
One-Shot Conversion mode:
1= Initiate a new conversion.
0= No effect.
bit 6-5
C1-C0: Channel Selection Bits
00 = Select Channel 1 (Default)
01 = Select Channel 2
10 = Select Channel 3 (MCP3428 only, treated as “00” by the MCP3426/MCP3427)
11 = Select Channel 4 (MCP3428 only, treated as “01” by the MCP3426/MCP3427)
bit 4
O/C: Conversion Mode Bit
1= Continuous Conversion Mode (Default). The device performs data conversions continuously.
0= One-Shot Conversion Mode. The device performs a single conversion and enters a low power
standby mode until it receives another write or read command.
bit 3-2
bit 1-0
S1-S0: Sample Rate Selection Bit
00 = 240 SPS (12 bits) (Default)
01 = 60 SPS (14 bits)
10 = 15 SPS (16 bits)
G1-G0: PGA Gain Selection Bits
00 = x1 (Default)
01 = x2
10 = x4
11 = x8
DS22226A-page 18
© 2009 Microchip Technology Inc.
MCP3426/7/8
I2C Serial Communications
If the configuration byte is read repeatedly by clocking
continuously after reading the data bytes (i.e., after the
4th byte in the 16-bit conversion mode), the state of the
RDY bit indicates whether the device is ready with new
conversion result. When the Master finds the RDY bit is
cleared, it can send a not-acknowledge (NAK) bit and
a stop bit to exit the current read operation and send a
new read command for the latest conversion data.
Once the conversion data has been read, the ready bit
toggles to ‘1’ until the next new conversion data is
ready. The conversion data in the output register is
overwritten every time a new conversion is completed.
5.3
The device communicates with the Master
(microcontroller) through a serial I2C (Inter-Integrated
Circuit) interface and support standard (100 kbits/sec),
fast (400 kbits/sec) and high-speed (3.4 Mbits/sec)
modes. The serial I2C is a bidirectional 2-wire data bus
communication protocol using open-drain SCL and
SDA lines.
The device can only be addressed as a slave. Once
addressed, it can receive configuration bits with a write
command or transmit the latest conversion results with
a read command. The serial clock pin (SCL) is an input
only and the serial data pin (SDA) is bidirectional. The
Master starts communication by sending a START bit
and terminates the communication by sending a STOP
bit. In read mode, the device releases the SDA line
after receiving NAK and STOP bits.
Figure 5-3 shows an example of writing configuration
register, and Figure 5-4 shows an example of reading
conversion data. The user can rewrite the configuration
byte any time for a new setting. Table 5-1 and Table 5-
2 show the examples of the configuration bit operation.
TABLE 5-1:
WRITE CONFIGURATION BITS
Operation
An example of a hardware connection diagram is
shown in Figure 6-1. More details of the I2C bus
characteristic is described in Section 5.6 “I2C Bus
Characteristics”.
R/W O/C RDY
0
0
0
No effect if all other bits remain
the same - operation continues
with the previous settings.
2
5.3.1
I C DEVICE ADDRESSING
0
0
0
0
1
1
1
0
1
Initiate One-Shot Conversion.
Initiate Continuous Conversion.
Initiate Continuous Conversion.
The first byte after the START bit is always the address
byte of the device, which includes the device code (4
bits), address bits (3 bits), and R/W bit. The device
code for the devices is 1101, which is programmed at
the factory. The I2C address bits (A2, A1, A0 bits) are
as follows:
TABLE 5-2:
READ CONFIGURATION BITS
Operation
• MCP3426: Programmed at factory
R/W O/C RDY
• MCP3427 and MCP3428: Progammed by the
user. It is determined by the logic status of the two
external address selection pins on the user’s
application board (Adr0 and Adr1 pins). The
Master must know the Adr0 and Adr1 pin
conditions before sending read or write command.
See Section 5.3.2 “Device Address Bits (A2,
A1, A0) and Address Selection Pins (MCP3427
and MCP3428)” for more details
1
1
1
1
0
0
1
1
0
1
0
1
New conversion result in One-
Shot conversion mode has just
been read. The RDY bit remains
low until set by a new write
command.
One-Shot Conversion is in prog-
ress. The conversion result is not
updated yet. The RDY bit stays
high until the current conversion
is completed.
Figure 5-1 shows the details of the address byte.
The three I2C address bits allow up to eight devices on
the same I2C bus line. The (R/W) bit determines if the
Master device wants to read the conversion data or
write to the Configuration register. If the (R/W) bit is set
(read mode), the device outputs the conversion data in
the following clocks. If the (R/W) bit is cleared (write
mode), the device expects a configuration byte in the
following clocks. When the device receives the correct
address byte, it outputs an acknowledge bit after the
R/W bit.
New conversion result in
Continuous Conversion mode
has just been read. The RDY bit
changes to high after reading the
conversion data.
The conversion result in
Continuous Conversion mode
was already read. The next new
conversion data is not ready. The
RDY bit stays high until a new
conversion is completed.
© 2009 Microchip Technology Inc.
DS22226A-page 19
MCP3426/7/8
It is recommended to issue a General Call Reset or
General Call Latch command once after the device
has powered up. This will ensure that the device reads
the address pins in a stable condition, and avoid
latching the address bits while the power supply is
ramping up. This might cause inaccurate address pin
detection.
Acknowledge bit
Read/Write bit
Start bit
Address
R/W ACK
Address Byte
When the address pin is left “floating”:
Address Byte:
When the address pin is left “floating”, the address pin
momentarily outputs a short pulse with an amplitude of
about VDD/2 during the latch event. The device also
latches this pin voltage at the same time.
Device Code
Address Bits (Note 1)
1
1
1
0
A2 A1
A0
If the “floating” pin is connected to a large parasitic
capacitance (> 20 pF) or to a long PCB trace, this short
floating voltage output can be altered. As a result, the
device may not latch the pin correctly.
Note 1: MCP3427 and MCP3428: Configured by
the user. See Table 5-4 for address bit
configurations.
2: MCP3426: Programmed at the factory
during production.
It is strongly recommended to keep the “floating” pin
pad as short as possible in the customer application
PCB and minimize the parasitic capacitance to the pin
as small as possible (< 20 pF).
FIGURE 5-1:
5.3.2
Address Byte.
Figure 5-2 shows an example of the Latch voltage
output at the address pin when the address pin is left
“floating”. The waveform at the Adr0 pin is captured by
using an oscilloscope probe with 15 pF of capacitance.
The device latches the floating condition immediately
after the General Call Latch command.
DEVICE ADDRESS BITS (A2, A1, A0)
AND ADDRESS SELECTION PINS
(MCP3427 AND MCP3428)
The MCP3427 and MCP3428 have two external
device address pins (Adr1, Adr0). These pins can be
set to a logic high (or tied to VDD), low (or tied to VSS),
or left floating (not connected to anything, or tied to
VDD/2), These combinations of logic level using the
two pins allow eight possible addresses. Table 5-3
shows the device address depending on the logic
status of the address selection pins.
Float waveform (output)
a
t address pin
The device samples the logic status of the Adr0 and
Adr1 pins in the following events:
SCL
SDA
(a) Device power-up.
(b) General Call Reset
(See Section 5.4 “General Call”).
(c) General Call Latch
(See Section 5.4 “General Call”).
FIGURE 5-2:
Command and Voltage Output at Address Pin
Left “Floating” (MCP3427 and MCP3428).
General Call Latch
The device samples the logic status (address pins)
during the above events, and latches the values until a
new latch event occurs. During normal operation (after
the address pins are latched), the address pins are
internally disabled from the rest of the internal circuit.
DS22226A-page 20
© 2009 Microchip Technology Inc.
MCP3426/7/8
TABLE 5-3:
ADDRESS BITS VS. ADDRESS
SELECTION PINS FOR
(MCP3427 AND MCP3428
ONLY) (NOTE 1, 2, 3)
5.3.3
WRITING A CONFIGURATION BYTE
TO THE DEVICE
When the Master sends an address byte with the R/W
bit low (R/W = 0), the device expects one configuration
byte following the address. Any byte sent after this
second byte will be ignored. The user can change the
operating mode of the device by writing the
configuration register bits.
I2C Device
Address Bits
Logic Status of Address
Selection Pins
A2
A1
A0
Adr0 Pin
Adr1 Pin
0
0
0
1
1
1
0
1
0
0
0
1
0
0
1
1
1
0
0
1
0
0
1
0
1
1
0
0 (Addr_Low)
0 (Addr_Low)
0 (Addr_Low)
0 (Addr_Low)
Float
If the device receives a write command with a new
configuration setting, the device immediately begins a
new conversion and updates the conversion data.
1 (Addr_High)
1 (Addr_High) 0 (Addr_Low)
1 (Addr_High) Float
1 (Addr_High) 1 (Addr_High)
Float
Float
Float
0 (Addr_Low)
1 (Addr_High)
Float
Note 1: Float: (a) Leave pin without connecting to
anything (left floating), or (b) apply
Addr_Float voltage.
2: The user can tie the pins to VSS or VDD
:
- Tie to VSS for Addr_Low
- Tie to VDD for Addr_High
3: See Addr_Low, Addr_High, and
Addr_Float parameters in Electrical
Characteristics Table.
1
1
9
9
SCL
SDA
1
1
1
A2 A1 A0
R/W
C1 C0
S1 S0 G1 G0
0
Start Bit by
Master
ACK by
MCP3426/7/8
Stop Bit by
Master
ACK by
MCP3426/7/8
O/C
RDY
(a) One-Shot Mode: 1
(b) Continuous Mode: not effected
1st Byte:
Address Byte
with Write command
2nd Byte:
Configuration Byte
Note:
– Stop bit can be issued any time during writing.
– MCP3426/7/8 device code is 1101(programmed at the factory).
– See Figure 5-1 for details in Address Byte.
FIGURE 5-3:
Timing Diagram For Writing To The MCP3426/7/8.
© 2009 Microchip Technology Inc.
DS22226A-page 21
MCP3426/7/8
The configuration byte follows the output data bytes.
The device repeatedly outputs the configuration byte
only if the Master sends clocks repeatedly after the
data bytes.
5.3.4
READING OUTPUT CODES AND
CONFIGURATION BYTE FROM THE
DEVICE
When the Master sends a read command (R/W = 1),
the device outputs both the conversion data and
configuration bytes. Each byte consists of 8 bits with
one acknowledge (ACK) bit. The ACK bit after the
address byte is issued by the device and the ACK bits
after each conversion data bytes are issued by the
Master.
The device terminates the current outputs when it
receives a Not-Acknowledge (NAK) with a repeated
start or a stop bit at the end of each output byte. It is not
required to read the configuration byte. However, the
Master may read the configuration byte to check the
RDY bit condition.The Master may continuously send
clock (SCL) to repeatedly read the configuration byte
(to check the RDY bit status).
When the device receives a read command, it outputs
two data bytes followed by a configuration register. In
16-bit conversion mode, the MSB (= sign bit) of the first
data byte is D15. In 14-bit conversion mode, the first
two bits in the first data byte are repeated MSB bits and
can be ignored, and the 3rd bit (D13) is the MSB (=sign
bit) of the conversion data. In 12-bit conversion mode,
the first four bits are repeated MSB bits and can be
ignored. The 5th bit (D11) of the byte represents the
MSB (= sign bit) of the conversion data. Table 5-4
summarizes the conversion data output of each
conversion mode.
Figure 5-4 shows the timing diagram for reading the
ADC conversion data.
TABLE 5-4:
OUTPUT CODES OF EACH RESOLUTION OPTION
Digital Output Codes
Conversion
Option
16-bits
14-bits
12-bits
D15 ~ D8 (1st data byte) - D7 ~ D0 (2nd data byte) - Configuration byte. (Note 1)
MMD13D ~ D8 (1st data byte) - D7 ~ D0 (2nd data byte) - Configuration byte. (Note 2)
MMMMD11 ~ D8 (1st data byte) - D7 ~ D0 (2nd data byte) - Configuration byte. (Note 3)
Note 1: D15 is MSB (= sign bit).
2: D13 is MSB (= sign bit), M is repeated MSB of the data byte.
3: D11 is MSB (= sign bit), M is repeated MSB of the data byte.
DS22226A-page 22
© 2009 Microchip Technology Inc.
MCP3426/7/8
FIGURE 5-4:
Timing Diagram For Reading From The MCP3426/7/8 With 12-Bit to 16-Bit Modes.
© 2009 Microchip Technology Inc.
DS22226A-page 23
MCP3426/7/8
5.4
General Call
5.5
High-Speed (HS) Mode
The device acknowledges the general call address
(0x00 in the first byte). The meaning of the general call
address is always specified in the second byte. Refer
to Figure 5-5. The device supports the following three
general calls.
For more information on the general call, or other I2C
modes, refer to the Phillips I2C specification.
The I2C specification requires that a high-speed mode
device must be ‘activated’ to operate in high-speed
mode. This is done by sending a special address byte
of “00001XXX” following the START bit. The “XXX”bits
are unique to the High-Speed (HS) mode Master. This
byte is referred to as the High-Speed (HS) Master
Mode Code (HSMMC). The MCP3426/7/8 devices do
not acknowledge this byte. However, upon receiving
this code, the device switches on its HS mode filters
and communicates up to 3.4 MHz on SDA and SCL
bus lines. The device will switch out of the HS mode on
the next STOP condition.
5.4.1
GENERAL CALL RESET
The general call reset occurs if the second byte is
‘00000110’ (06h). At the acknowledgement of this
byte, the device will abort current conversion and
perform the following tasks:
For more information on the HS mode, or other I2C
modes, refer to the Philips I2C specification.
(a) Internal reset similar to a Power-On-Reset (POR).
All configuration and data register bits are reset to
default values.
5.6
I2C Bus Characteristics
The I2C specification defines the following bus
protocol:
(b) Latch the logic status of external address selection
pins (Adr0 and Adr1 pins).
• Data transfer may be initiated only when the bus
is not busy
5.4.2
GENERAL CALL LATCH (MCP3427
AND MCP3428)
• During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is HIGH will be
interpreted as a START or STOP condition
The general call latch occurs if the second byte is
‘00000100’(04h). The device will latch the logic sta-
tus of the external address selection pins (Adr0 and
Adr1 pins), but will not perform a reset.
Accordingly, the following bus conditions have been
defined using Figure 5-6.
5.4.3
GENERAL CALL CONVERSION
5.6.1
BUS NOT BUSY (A)
The general call conversion occurs if the second byte
is ‘00001000’(08h). All devices on the bus initiate a
conversion simultaneously. When the device receives
this command, the configuration will be set to the
One-Shot Conversion mode and a single conversion
will be performed. The PGA and data rate settings are
unchanged with this general call.
Both data and clock lines remain HIGH.
5.6.2
START DATA TRANSFER (B)
A HIGH to LOW transition of the SDA line while the
clock (SCL) is HIGH determines a START condition. All
commands must be preceded by a START condition.
START
LSB STOP
5.6.3
STOP DATA TRANSFER (C)
A LOW to HIGH transition of the SDA line while the
clock (SCL) is HIGH determines a STOP condition. All
operations can be ended with a STOP condition.
S
0 0 0 0 0 0 0 0
A
X X X X X X X X A S
5.6.4
DATA VALID (D)
ACK
ACK
First Byte
(General Call Address)
Second Byte
The state of the data line represents valid data when,
after a START condition, the data line is stable for the
duration of the HIGH period of the clock signal.
Note:
The I2C specification does not allow
‘00000000’ (00h) in the second byte.
The data on the line must be changed during the LOW
period of the clock signal. There is one clock pulse per
bit of data.
FIGURE 5-5:
General Call Address
Format.
Each data transfer is initiated with a START condition
and terminated with a STOP condition.
DS22226A-page 24
© 2009 Microchip Technology Inc.
MCP3426/7/8
During reads, the Master (microcontroller) can
terminate the current read operation by not providing
an acknowledge bit (not Acknowledge (NAK)) on the
last byte. In this case, the MCP3426/7/8 devices
release the SDA line to allow the Master
(microcontroller) to generate a STOP or repeated
START condition.
5.6.5
ACKNOWLEDGE AND
NON-ACKNOWLEDGE
The Master (microcontroller) and the slave (MCP3426/
7/8) use an acknowledge pulse (ACK) as a hand shake
of communication for each byte. The ninth clock pulse
of each byte is used for the acknowledgement. The
clock pulse is always provided by the Master
(microcontroller) and the acknowledgement is issued
by the receiving device of the byte (Note: The
transmitting device must release the SDA line during
the acknowledge pulse.). The acknowledgement is
achieved by pulling-down the SDA line “LOW” during
the 9th clock pulse by the receiving device.
The non-acknowledgement (NAK) is issued by
providing the SDA line to “HIGH” during the 9th clock
pulse.
(A)
(B)
(D)
(D)
(C) (A)
SCL
SDA
START
STOP
ADDRESS OR
DATA
CONDITION
CONDITION
ACKNOWLEDGE ALLOWED
VALID TO CHANGE
2
FIGURE 5-6:
Data Transfer Sequence on I C Serial Bus.
© 2009 Microchip Technology Inc.
DS22226A-page 25
MCP3426/7/8
2
TABLE 5-5:
I C SERIAL TIMING SPECIFICATIONS
Electrical Specifications: Unless otherwise specified, all limits are specified for TA = -40 to +85°C, VDD = +2.7V to +5.0V,
V
SS = 0V, CHn+ = CHn- = VREF/2.
Parameters
Sym
Min
Typ
Max
Units
Conditions
Standard Mode (100 kHz)
Clock frequency
fSCL
0
—
—
—
—
—
—
100
—
kHz
ns
Clock high time
T
4000
4700
—
HIGH
Clock low time
T
—
ns
LOW
SDA and SCL rise time
SDA and SCL fall time
START condition hold time
T
1000
300
—
ns
From VIL to VIH (Note 1)
From VIH to VIL (Note 1)
R
T
—
ns
F
T
T
4000
ns
After this period, the first clock
pulse is generated.
HD:STA
Repeated START condition
setup time
4700
—
—
ns
Only relevant for repeated Start
condition
SU:STA
Data hold time
T
T
0
—
—
—
—
—
3450
—
ns
ns
ns
ns
ns
(Note 3)
HD:DAT
SU:DAT
SU:STO
Data input setup time
STOP condition setup time
Output valid from clock
Bus free time
250
4000
0
T
—
T
3750
—
(Note 2, Note 3)
AA
T
4700
Time between START and STOP
conditions.
BUF
Fast Mode (400 kHz)
Clock frequency
T
0
—
—
—
—
—
—
400
—
kHz
ns
SCL
Clock high time
T
600
HIGH
Clock low time
T
1300
—
ns
LOW
SDA and SCL rise time
SDA and SCL fall time
START condition hold time
T
20 + 0.1Cb
20 + 0.1Cb
600
300
300
—
ns
From VIL to VIH (Note 1)
From VIH to VIL (Note 1)
R
T
ns
F
T
T
ns
After this period, the first clock
pulse is generated
HD:STA
Repeated START condition
setup time
600
—
—
ns
Only relevant for repeated Start
condition
SU:STA
Data hold time
T
T
0
100
600
0
—
—
—
—
—
900
—
ns
ns
ns
ns
ns
(Note 4)
HD:DAT
SU:DAT
SU:STO
Data input setup time
STOP condition setup time
Output valid from clock
Bus free time
T
—
T
1200
—
(Note 2, Note 3)
AA
T
1300
Time between START and STOP
conditions.
BUF
Input filter spike suppression
T
0
—
50
ns
SDA and SCL pins (Note 5)
SP
Note 1: This parameter is ensured by characterization and not 100% tested.
2: This specification is not a part of the I2C specification. This specification is equivalent to the Data Hold Time (T
)
HD:DAT
plus SDA Fall (or rise) time: TAA = THD:DAT + TF (OR TR).
3: If this parameter is too short, it can create an unintended Start or Stop condition to other devices on the bus line. If this
parameter is too long, Clock Low time (TLOW) can be affected.
4: For Data Input: This parameter must be longer than tSP. If this parameter is too long, the Data Input Setup (TSU:DAT) or
Clock Low time (TLOW) can be affected.
For Data Output: This parameter is characterized, and tested indirectly by testing TAA parameter.
5: This parameter is ensured by characterization and not 100% tested. This parameter is not available for Standard Mode.
DS22226A-page 26
© 2009 Microchip Technology Inc.
MCP3426/7/8
2
TABLE 5-5:
I C SERIAL TIMING SPECIFICATIONS (CONTINUED)
Electrical Specifications: Unless otherwise specified, all limits are specified for TA = -40 to +85°C, VDD = +2.7V to +5.0V,
V
SS = 0V, CHn+ = CHn- = VREF/2.
Parameters
Sym
Min
Typ
Max
Units
Conditions
High Speed Mode (3.4 MHz)
Clock frequency
fSCL
0
—
—
—
—
—
—
—
3.4
1.7
—
MHz
MHz
ns
Cb = 100 pF
Cb = 400 pF
0
Clock high time
Clock low time
T
60
Cb = 100 pF, fSCL = 3.4 MHz
Cb = 400 pF, fSCL = 1.7 MHz
Cb = 100 pF, fSCL = 3.4 MHz
Cb = 400 pF, fSCL = 1.7 MHz
HIGH
120
160
320
—
—
ns
T
—
ns
LOW
—
ns
SCL rise time
(Note 1)
T
40
ns
From VIL to VIH
Cb = 100 pF, fSCL = 3.4 MHz
From VIL to VIH
,
R
—
—
—
—
—
—
—
—
—
—
—
—
—
—
80
40
ns
ns
ns
ns
ns
ns
ns
,
Cb = 400 pF, fSCL = 1.7 MHz
SCL fall time
(Note 1)
T
From VIH to VIL,
Cb = 100 pF, fSCL = 3.4 MHz
F
80
From VIH to VIL,
Cb = 400 pF, fSCL = 1.7 MHz
SDA rise time
(Note 1)
T
80
From VIL to VIH
Cb = 100 pF, fSCL = 3.4 MHz
From VIL to VIH
,
R: DAT
160
80
,
Cb = 400 pF, fSCL = 1.7 MHz
SDA fall time
(Note 1)
T
T
From VIH to VIL,
Cb = 100 pF, fSCL = 3.4 MHz
F: DATA
160
From VIH to VIL,
Cb = 400 pF, fSCL = 1.7 MHz
Data hold time
(Note 4)
0
0
—
—
—
—
—
70
150
150
310
—
ns
ns
ns
ns
ns
Cb = 100 pF, fSCL = 3.4 MHz
Cb = 400 pF, fSCL = 1.7 MHz
Cb = 100 pF, fSCL = 3.4 MHz
Cb = 400 pF, fSCL = 1.7 MHz
HD:DAT
Output valid from clock
(Notes 2 and 3)
T
—
—
160
AA
START condition hold time
T
After this period, the first clock
pulse is generated
HD:STA
Repeated START condition
setup time
TSU:STA
160
—
—
ns
Only relevant for repeated Start
condition
Data input setup time
T
10
160
0
—
—
—
—
—
10
ns
ns
ns
SU:DAT
T
SU:STO
STOP condition setup time
Input filter spike suppression
T
SDA and SCL pins (Note 5)
SP
Note 1: This parameter is ensured by characterization and not 100% tested.
2: This specification is not a part of the I2C specification. This specification is equivalent to the Data Hold Time (T
)
HD:DAT
plus SDA Fall (or rise) time: TAA = THD:DAT + TF (OR TR).
3: If this parameter is too short, it can create an unintended Start or Stop condition to other devices on the bus line. If this
parameter is too long, Clock Low time (TLOW) can be affected.
4: For Data Input: This parameter must be longer than tSP. If this parameter is too long, the Data Input Setup (TSU:DAT) or
Clock Low time (TLOW) can be affected.
For Data Output: This parameter is characterized, and tested indirectly by testing TAA parameter.
5: This parameter is ensured by characterization and not 100% tested. This parameter is not available for Standard Mode.
© 2009 Microchip Technology Inc.
DS22226A-page 27
MCP3426/7/8
TF
TR
THIGH
TSU:STA
SCL
TSU:STO
TBUF
TSU:DAT
TLOW
THD:STA
THD:DAT
SDA
0.7VDD
0.3VDD
TSP
TAA
2
FIGURE 5-7:
I C Bus Timing Data.
DS22226A-page 28
© 2009 Microchip Technology Inc.
MCP3426/7/8
2
6.1.3
I C ADDRESS SELECTION PINS
(MCP3427 AND MCP3428)
6.0
BASIC APPLICATION
CONFIGURATION
The user can tie the Adr0 and Adr1 pins to VSS, VDD
,
The MCP3426/7/8 devices can be used for various
precision analog-to-digital converter applications.
These devices operate with very simple connections to
the application circuit. The following sections discuss
the examples of the device connections and
applications.
or left floating. See more details in Section 5.3.2
“Device Address Bits (A2, A1, A0) and Address
Selection Pins (MCP3427 and MCP3428)”.
MCP3428
Input
Input
Signal 1
1
2
3
4
5
6
7
CH1+
CH1-
CH4- 14
Signal 4
6.1
Connecting to the Application
Circuits
13
12
CH4+
CH3-
Input
Input
CH2+
CH2-
Signal 3
Signal 2
11
CH3+
2
6.1.1
BYPASS CAPACITORS ON V PIN
V
I C Address
Selection
Pins
Adr1 10
SS
DD
V
9
DD
Adr0
For an accurate measurement, the application circuit
needs a clean supply voltage and must block any noise
signal to the MCP3426/7/8 devices. Figure 6-1 shows
an example of using two bypass capacitors (a 10 µF
tantalum capacitor and a 0.1 µF ceramic capacitor) on
the VDD line of the MCP3428. These capacitors are
helpful to filter out any high frequency noises on the
VDD line and also provide the momentary bursts of
extra currents when the device needs from the supply.
These capacitors should be placed as close to the VDD
pin as possible (within one inch). If the application
circuit has separate digital and analog power supplies,
the VDD and VSS of the MCP3426/7/8 devices should
reside on the analog plane.
C
1
SDA
8
SCL
C
2
TO MCU
(MASTER)
RP
RP
V
DD
Rp is the pull-up resistor:
5 kΩ - 10 kΩ for fSCL = 100 kHz to 400 kHz
~700Ω for fSCL = 3.45 MHz
C1: 0.1 µF, Ceramic capacitor
2
6.1.2
CONNECTING TO I C BUS USING
PULL-UP RESISTORS
C2: 10 µF, Tantalum capacitor
FIGURE 6-1:
Typical Connection.
The SCL and SDA pins of the MCP3426/7/8 are
open-drain configurations. These pins require a pull-up
resistor as shown in Figure 6-1. The value of these
pull-up resistors depends on the operating speed
(standard, fast, and high speed) and loading
capacitance of the I2C bus line. Higher value of pull-up
resistor consumes less power, but increases the signal
transition time (higher RC time constant) on the bus.
Therefore, it can limit the bus operating speed. The
lower value of resistor, on the other hand, consumes
higher power, but allows higher operating speed. If the
bus line has higher capacitance due to long bus line or
high number of devices connected to the bus, a smaller
pull-up resistor is needed to compensate the long RC
time constant. The pull-up resistor is typically chosen
between 5 kΩ and 10 kΩ ranges for standard and fast
modes, and less than 1 kΩ for high speed mode
depending on the presence of bus loading capacitance.
Figure 6-2 shows an example of multiple device
connections. The I2C bus loading capacitance
increases as the number of device connected to the I2C
bus line increases. The bus loading capacitance affects
on the bus operating speed. For example, the highest
bus operating speed for the 400 pF bus capacitance is
1.7 MHz, and 3.4 MHz for 100 pF. Therefore, the user
needs to consider the relationship between the
maximum operation speed versus. the number of I2C
devices that are connected to the I2C bus line.
SDA SCL
Microcontroller
(PIC16F876)
MCP3426
MCP3427
MCP3428
MCP4725
FIGURE 6-2:
Connection on I C Bus.
Example of Multiple Device
2
© 2009 Microchip Technology Inc.
DS22226A-page 29
MCP3426/7/8
6.1.4
DEVICE CONNECTION TEST
6.1.5
DIFFERENTIAL AND
SINGLE-ENDED CONFIGURATION
The user can test the presence of the MCP3426/7/8 on
the I2C bus line without performing an input data
conversion. This test can be achieved by checking an
acknowledge response from the MCP3426/7/8 after
sending a read or write command. Here is an example
using Figure 6-3:
Figure 6-4 shows typical connection examples for
differential and single-ended inputs. Differential input
signals can be connected to the CHn+ and CHn- input
pins, where n = the channel number (1, 2, 3, or 4). For
the single-ended input, the input signal is applied to one
of the input pins (typically connected to the CHn+ pin)
while the other input pin (typically CHn- pin) is
grounded. All device characteristics hold for the
single-ended configuration, but this configuration loses
one bit resolution because the input can only stand in
positive half scale. Refer to Section 1.0 “Electrical
a. Set the R/W bit “HIGH” in the address byte.
b. Check the ACK pulse after sending the address
byte.
If the device acknowledges (ACK = 0), then the
device is connected, otherwise it is not
connected.
Characteristics”
.
c. Send STOP or START bit.
(a) Differential Input Signal Connection:
Excitation
Address Byte
Sensor
1
1
2
1
3
0
4
5
6
7
8
1
9
SCL
SDA
CHn+
Input Signal
1 A2 A1 A0
CHn-
MCP342X
Start
Bit
Stop
Bit
Address bits
Device bits
R/W
(b) Single-ended Input Signal Connection:
MCP342X
Response
Excitation
R1
2
FIGURE 6-3:
I C Bus Connection Test.
CHn+
Input Signal
Sensor
R2
CHn-
MCP342X
FIGURE 6-4:
Differential and
Single-Ended Input Connections.
DS22226A-page 30
© 2009 Microchip Technology Inc.
MCP3426/7/8
Therefore, the current measurement often prefers to
use a current sensor with smaller resistance value,
which, in turn, requires high resolution ADC device.
6.2
Application Examples
The MCP3426/7/8 devices can be used for broad
ranges of sensor and data acquisition applications.
The device can measure the input voltage as low as
7.8 µV range (or current in ~ µA range) with 16 bit
resolution and PGA = 8 settings.
Figure 6-5 shows a circuit example measuring both the
battery voltage and current using the MCP3426 device.
Channels 1 and 2 are measuring the voltage and the
current, respectively.
The MSB (= sign bit) of the output code determines the
direction of the current, which identifies the charging or
the discharging current.
When the input voltage is greater than the internal
reference voltage (VREF = 2.048V), it needs a voltage
divider circuit to prevent the output code from being
saturated. In the example, R1 and R2 form a voltage
divider. The R1 and R2 are set to yield VIN to be less
than the internal reference voltage (VREF = 2.048V).
For the current measurement, the device measure the
voltage across the current sensor, and converts it by
dividing the measured voltage by a known resistance
value. The voltage drops across the sensor is waste.
Discharging Current
To Load
Current Sensor
Charging
Current
To Battery
R1
Battery
VBAT
MCP3426
VIN
(Rechargeable)
8
1
2
CH2-
CH1+
CH1-
VDD
SDA
7
6
5
CH2+
VSS
3
4
0.1 µF
SCL
R2
SCL
10 µF
TO MCU
(MASTER)
SDA
R2
------------------
VIN
=
× VBAT
5 kΩ
R1 + R2
5 kΩ
R1 and R2 = Voltage Divider
VDD
FIGURE 6-5:
Battery Voltage and Charging/Discharging Current Measurement.
© 2009 Microchip Technology Inc.
DS22226A-page 31
MCP3426/7/8
Figure 6-6, shows an example of using the MCP3428
for
four-channel
thermocouple
temperature
measurement applications.
Thermocouple Sensor
Isothermal Block
Isothermal Block
MCP9800
MCP3428
MCP9800
1
2
CH1+
CH1-
14
13
12
11
CH4-
SDA
SCL
SDA
CH4+
CH3-
SCL
3 CH2+
CH2-
4
CH3+
Adr1
Adr0
SCL
5 VSS
10
9
8
VDD
0.1 µF
10 µF
VDD
6
7
SDA
MCP9800
MCP9800
SDA
Heat
SCL
SCL
SDA
SCL
TO MCU
SDA
(MASTER)
5 kΩ
5 kΩ
VDD
FIGURE 6-6:
Four-Channel Thermocouple Applications.
With Type
K
thermocouple, it can measure
EQUATION 6-1:
temperature from 0°C to +1250°C degrees. The full
scale output range of the Type K thermocouple is
about 50 mV. This provides 40 µV/°C (= 50 mV/
1250°C) of measurement resolution. Equation 6-1
shows the measurement budget for sensor signal using
the MCP3426/7/8 device with 16 bits and PGA = 8
settings. With this configuration, the MCP3428 can
detect the input signal level as low as approximately
7.8 µV. By setting the internal PGA option to x8, the
40 µV/°C input from the thermocouple is amplified
internally to 320 µV/°C before the conversion takes
place. This results in about 5 LSB output codes per
1°C of change in temperature, with 16-bit conversion
mode.
Detectable Input Signal Level = 62.5μV/PGA
= 7.8125μV for PGA = 8
Input Signal Level after gain of 8:
= (40μV/°C) • 8 = 320μV/°C
320μV/°C
No. of LSB/°C = ------------------------ = 5.12 Codes/°C
62.5μV
Where:
1 LSB
=
62.5 µV with 16 bit configuration
DS22226A-page 32
© 2009 Microchip Technology Inc.
MCP3426/7/8
Equation 6-2 shows an example of calculating the
expected number of output code with various PGA gain
settings for Type K thermocouple output.
EQUATION 6-2:
EXPECTED NUMBER OF
OUTPUT CODE FOR TYPE
K THERMOCOUPLE
Expected
Number of Output Code =
⎛
⎜
⎜
⎝
⎞
⎟
⎟
⎠
50 mV
-----------------
log2
62.5μV
-----------------
PGA
ln(800 • PGA)
⎛
⎝
⎞
⎠
=
-------------------------------------
ln(2)
= 9.6 bits for PGA = 1
= 10.6 bits for PGA = 2
= 11.6 bits for PGA = 4
= 12.6 bits for PGA = 8
Where:
1 LSB
=
62.5 µV with 16 Bit configuration.
VDD
VDD
Pressure Sensor
(NPP301)
Pressure Sensor
(NPP301)
MCP3428
1
2
CH1+
CH1-
14
CH4-
13
12
CH4+
CH3-
VIN
VDD
3 CH2+
VIN
CH2-
VSS
VDD
SDA
11
10
4
5
6
VDD
CH3+
Adr1
VDD
R1
9
8
Adr0
SCL
0.1 µF
7
R1
R2
R2
Thermistor
10 µF
TO MCU
(MASTER)
Thermistor
5 kΩ
5 kΩ
VDD
R2
------------------
R1 + R2
VIN
=
× VDD
R1 and R2 = Voltage Divider
FIGURE 6-7:
Example of Pressure and Temperature Measurement.
© 2009 Microchip Technology Inc.
DS22226A-page 33
MCP3426/7/8
Figure 6-7 shows an example of measuring both
pressure and temperature. The pressure is measured
by using NPP 301 (manufactured by GE NovaSensor),
and temperature is measured by a thermistor. The
pressure sensor output is 20 mV/V. This gives 100 mV
of full scale output for VDD of 5V (sensor excitation
voltage). Equation 6-3 shows an example of calculating
the number of output code for the full scale output of the
NPP301.
EQUATION 6-3:
EXPECTED NUMBER OF
OUTPUT CODE FOR
NPP301 PRESSURE
SENSOR
⎛
⎜
⎜
⎝
⎞
⎟
⎟
⎠
Expected
Number of Output Code =
100 mV
--------------------
log2
62.5μV
-----------------
PGA
ln(1600 • PGA)
⎛
⎝
⎞
⎠
=
----------------------------------------
ln(2)
= 10.6 bits for PGA = 1
= 11.6 bits for PGA = 2
= 12.6 bits for PGA = 4
= 13.6 bits for PGA = 8
Where:
1 LSB
=
62.5 µV with 16 Bit configuration.
The thermistor temperature sensor can measure the
temperature range from -100°C to +300°C. The
resistance of the thermistor sensor decreases as
temperature
increases
(negative
temperature
coefficient). As shown in Figure 6-7, the thermistor (R2)
forms a voltage divider with R1.
The thermistor sensor is simple to use and widely used
for the temperature measurement applications. It has
both linear and non-linear responses over temperature
range. R1 is used to adjust the linear region of interest
for measurement.
DS22226A-page 34
© 2009 Microchip Technology Inc.
MCP3426/7/8
7.0
7.1
PACKAGING INFORMATION
Package Marking Information
Example:
8-Lead DFN (2x3) (MCP3426)
XXX
YWW
NN
ABX
945
25
Example:
8-Lead MSOP (MCP3426)
XXXXXX
3426A0
945256
YWWNNN
8-Lead SOIC (300 mil) (MCP3426)
Example:
3426A0E
XXXXXXXX
XXXXYYWW
e
3
SN^^0945
256
NNN
Legend: XX...X Customer-specific information
Y
YY
WW
NNN
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
e
3
Pb-free JEDEC designator for Matte Tin (Sn)
*
This package is Pb-free. The Pb-free JEDEC designator (
can be found on the outer packaging for this package.
)
e3
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
© 2009 Microchip Technology Inc.
DS22226A-page 35
MCP3426/7/8
Package Marking Information (Continued)
10-Lead DFN (3x3) (MCP3427)
Example:
1
2
3
4
5
10
9
1
10
9
XXXX
YYWW
NNN
3427
0945
256
2
3
4
5
8
8
7
7
6
6
Example:
10-Lead MSOP (MCP3427)
3427E
945256
XXXXXX
YWWNNN
14-Lead SOIC (150 mil) (MCP3428)
Example:
MCP3428
E/SL
XXXXXXXXXXX
XXXXXXXXXXX
e
3
YYWWNNN
0945256
14-Lead TSSOP (4.4 mm) (MCP3428)
Example:
XXXXXXXX
YYWW
MCP3428E
0945
NNN
256
DS22226A-page 36
© 2009 Microchip Technology Inc.
MCP3426/7/8
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢆꢏꢈꢄꢊꢐꢆꢑꢒꢆꢂꢃꢄꢅꢆꢇꢄꢌꢓꢄꢔꢃꢆꢕꢖꢗꢘꢆMꢆꢙꢚꢛꢚꢜ !ꢆ""ꢆ#ꢒꢅ$ꢆ%ꢍꢏꢑ&
ꢑꢒꢊꢃ' 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ*ꢇꢐꢉꢅ"ꢊꢇ)ꢃꢄꢐ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢖꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ*ꢇꢐꢃꢄꢐꢅꢕꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ133)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ*ꢇꢐꢃꢄꢐ
e
D
b
N
N
L
K
E2
E
EXPOSED PAD
NOTE 1
NOTE 1
2
1
1
2
D2
BOTTOM VIEW
TOP VIEW
A
NOTE 2
A3
A1
4ꢄꢃ%
ꢖꢙ55ꢙꢖ,ꢗ,ꢘꢕ
ꢓꢃ&ꢉꢄ ꢃꢌꢄꢅ5ꢃ&ꢃ%
ꢖꢙ6
67ꢖ
9
ꢚꢁ.ꢚꢅ/ꢕ0
ꢚꢁꢛꢚ
ꢖꢔ8
6!&(ꢉꢊꢅꢌ$ꢅꢂꢃꢄ
ꢂꢃ%ꢍꢎ
7ꢆꢉꢊꢇꢈꢈꢅ:ꢉꢃꢐꢎ%
ꢕ%ꢇꢄ"ꢌ$$ꢅ
0ꢌꢄ%ꢇꢍ%ꢅꢗꢎꢃꢍ*ꢄꢉ
7ꢆꢉꢊꢇꢈꢈꢅ5ꢉꢄꢐ%ꢎ
7ꢆꢉꢊꢇꢈꢈꢅ;ꢃ"%ꢎ
6
ꢉ
ꢔ
ꢔꢀ
ꢔ+
ꢓ
ꢚꢁ9ꢚ
ꢚꢁꢚꢚ
ꢀꢁꢚꢚ
ꢚꢁꢚ.
ꢚꢁꢚꢏ
ꢚꢁꢏꢚꢅꢘ,2
ꢏꢁꢚꢚꢅ/ꢕ0
+ꢁꢚꢚꢅ/ꢕ0
M
M
ꢚꢁꢏ.
,
,#ꢑꢌ ꢉ"ꢅꢂꢇ"ꢅ5ꢉꢄꢐ%ꢎ
,#ꢑꢌ ꢉ"ꢅꢂꢇ"ꢅ;ꢃ"%ꢎ
0ꢌꢄ%ꢇꢍ%ꢅ;ꢃ"%ꢎ
0ꢌꢄ%ꢇꢍ%ꢅ5ꢉꢄꢐ%ꢎ
0ꢌꢄ%ꢇꢍ%ꢝ%ꢌꢝ,#ꢑꢌ ꢉ"ꢅꢂꢇ"
ꢓꢏ
,ꢏ
(
5
=
ꢀꢁ+ꢚ
ꢀꢁ.ꢚ
ꢚꢁꢏꢚ
ꢚꢁ+ꢚ
ꢚꢁꢏꢚ
ꢀꢁ..
ꢀꢁꢜ.
ꢚꢁ+ꢚ
ꢚꢁ.ꢚ
M
ꢚꢁꢒꢚ
M
ꢑꢒꢊꢃꢉ'
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃ !ꢇꢈꢅꢃꢄ"ꢉ#ꢅ$ꢉꢇ%!ꢊꢉꢅ&ꢇꢋꢅꢆꢇꢊꢋ'ꢅ(!%ꢅ&! %ꢅ(ꢉꢅꢈꢌꢍꢇ%ꢉ"ꢅ)ꢃ%ꢎꢃꢄꢅ%ꢎꢉꢅꢎꢇ%ꢍꢎꢉ"ꢅꢇꢊꢉꢇꢁ
ꢏꢁ ꢂꢇꢍ*ꢇꢐꢉꢅ&ꢇꢋꢅꢎꢇꢆꢉꢅꢌꢄꢉꢅꢌꢊꢅ&ꢌꢊꢉꢅꢉ#ꢑꢌ ꢉ"ꢅ%ꢃꢉꢅ(ꢇꢊ ꢅꢇ%ꢅꢉꢄ" ꢁ
+ꢁ ꢂꢇꢍ*ꢇꢐꢉꢅꢃ ꢅ ꢇ)ꢅ ꢃꢄꢐ!ꢈꢇ%ꢉ"ꢁ
ꢒꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄꢃꢄꢐꢅꢇꢄ"ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢃꢄꢐꢅꢑꢉꢊꢅꢔꢕꢖ,ꢅ-ꢀꢒꢁ.ꢖꢁ
/ꢕ01 /ꢇ ꢃꢍꢅꢓꢃ&ꢉꢄ ꢃꢌꢄꢁꢅꢗꢎꢉꢌꢊꢉ%ꢃꢍꢇꢈꢈꢋꢅꢉ#ꢇꢍ%ꢅꢆꢇꢈ!ꢉꢅ ꢎꢌ)ꢄꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ ꢁ
ꢘ,21 ꢘꢉ$ꢉꢊꢉꢄꢍꢉꢅꢓꢃ&ꢉꢄ ꢃꢌꢄ'ꢅ! !ꢇꢈꢈꢋꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ'ꢅ$ꢌꢊꢅꢃꢄ$ꢌꢊ&ꢇ%ꢃꢌꢄꢅꢑ!ꢊꢑꢌ ꢉ ꢅꢌꢄꢈꢋꢁ
ꢖꢃꢍꢊꢌꢍꢎꢃꢑ ꢗꢉꢍꢎꢄꢌꢈꢌꢐꢋ ꢓꢊꢇ)ꢃꢄꢐ 0ꢚꢒꢝꢀꢏ+0
© 2009 Microchip Technology Inc.
DS22226A-page 37
MCP3426/7/8
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢆꢏꢈꢄꢊꢐꢆꢑꢒꢆꢂꢃꢄꢅꢆꢇꢄꢌꢓꢄꢔꢃꢆꢕꢖꢗꢘꢆMꢆꢙꢚꢛꢚꢜ !ꢆ""ꢆ#ꢒꢅ$ꢆ%ꢍꢏꢑ&
ꢑꢒꢊꢃ' 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ*ꢇꢐꢉꢅ"ꢊꢇ)ꢃꢄꢐ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢖꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ*ꢇꢐꢃꢄꢐꢅꢕꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ133)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ*ꢇꢐꢃꢄꢐ
DS22226A-page 38
© 2009 Microchip Technology Inc.
MCP3426/7/8
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢖꢋꢌ(ꢒꢆ)"ꢄꢈꢈꢆ*ꢎꢊꢈꢋ+ꢃꢆꢇꢄꢌꢓꢄꢔꢃꢆꢕꢖ)ꢘꢆ%ꢖ)*ꢇ&
ꢑꢒꢊꢃ' 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ*ꢇꢐꢉꢅ"ꢊꢇ)ꢃꢄꢐ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢖꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ*ꢇꢐꢃꢄꢐꢅꢕꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ133)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ*ꢇꢐꢃꢄꢐ
D
N
E
E1
NOTE 1
2
b
1
e
c
φ
A2
A
L
L1
A1
4ꢄꢃ%
ꢖꢙ55ꢙꢖ,ꢗ,ꢘꢕ
ꢓꢃ&ꢉꢄ ꢃꢌꢄꢅ5ꢃ&ꢃ%
ꢖꢙ6
67ꢖ
ꢖꢔ8
6!&(ꢉꢊꢅꢌ$ꢅꢂꢃꢄ
ꢂꢃ%ꢍꢎ
6
ꢉ
9
ꢚꢁ>.ꢅ/ꢕ0
7ꢆꢉꢊꢇꢈꢈꢅ:ꢉꢃꢐꢎ%
ꢖꢌꢈ"ꢉ"ꢅꢂꢇꢍ*ꢇꢐꢉꢅꢗꢎꢃꢍ*ꢄꢉ
ꢕ%ꢇꢄ"ꢌ$$ꢅ
7ꢆꢉꢊꢇꢈꢈꢅ;ꢃ"%ꢎ
ꢖꢌꢈ"ꢉ"ꢅꢂꢇꢍ*ꢇꢐꢉꢅ;ꢃ"%ꢎ
7ꢆꢉꢊꢇꢈꢈꢅ5ꢉꢄꢐ%ꢎ
2ꢌꢌ%ꢅ5ꢉꢄꢐ%ꢎ
ꢔ
M
ꢚꢁꢜ.
ꢚꢁꢚꢚ
M
ꢚꢁ9.
ꢀꢁꢀꢚ
ꢚꢁꢛ.
ꢚꢁꢀ.
ꢔꢏ
ꢔꢀ
,
,ꢀ
ꢓ
M
ꢒꢁꢛꢚꢅ/ꢕ0
+ꢁꢚꢚꢅ/ꢕ0
+ꢁꢚꢚꢅ/ꢕ0
ꢚꢁ>ꢚ
5
ꢚꢁꢒꢚ
ꢚꢁ9ꢚ
2ꢌꢌ%ꢑꢊꢃꢄ%
2ꢌꢌ%ꢅꢔꢄꢐꢈꢉ
5ꢀ
ꢀ
ꢚꢁꢛ.ꢅꢘ,2
M
ꢚꢞ
9ꢞ
5ꢉꢇ"ꢅꢗꢎꢃꢍ*ꢄꢉ
5ꢉꢇ"ꢅ;ꢃ"%ꢎ
ꢍ
(
ꢚꢁꢚ9
ꢚꢁꢏꢏ
M
M
ꢚꢁꢏ+
ꢚꢁꢒꢚ
ꢑꢒꢊꢃꢉ'
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃ !ꢇꢈꢅꢃꢄ"ꢉ#ꢅ$ꢉꢇ%!ꢊꢉꢅ&ꢇꢋꢅꢆꢇꢊꢋ'ꢅ(!%ꢅ&! %ꢅ(ꢉꢅꢈꢌꢍꢇ%ꢉ"ꢅ)ꢃ%ꢎꢃꢄꢅ%ꢎꢉꢅꢎꢇ%ꢍꢎꢉ"ꢅꢇꢊꢉꢇꢁ
ꢏꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄ ꢅꢓꢅꢇꢄ"ꢅ,ꢀꢅ"ꢌꢅꢄꢌ%ꢅꢃꢄꢍꢈ!"ꢉꢅ&ꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢁꢅꢖꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢅ ꢎꢇꢈꢈꢅꢄꢌ%ꢅꢉ#ꢍꢉꢉ"ꢅꢚꢁꢀ.ꢅ&&ꢅꢑꢉꢊꢅ ꢃ"ꢉꢁ
+ꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄꢃꢄꢐꢅꢇꢄ"ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢃꢄꢐꢅꢑꢉꢊꢅꢔꢕꢖ,ꢅ-ꢀꢒꢁ.ꢖꢁ
/ꢕ01 /ꢇ ꢃꢍꢅꢓꢃ&ꢉꢄ ꢃꢌꢄꢁꢅꢗꢎꢉꢌꢊꢉ%ꢃꢍꢇꢈꢈꢋꢅꢉ#ꢇꢍ%ꢅꢆꢇꢈ!ꢉꢅ ꢎꢌ)ꢄꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ ꢁ
ꢘ,21 ꢘꢉ$ꢉꢊꢉꢄꢍꢉꢅꢓꢃ&ꢉꢄ ꢃꢌꢄ'ꢅ! !ꢇꢈꢈꢋꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ'ꢅ$ꢌꢊꢅꢃꢄ$ꢌꢊ&ꢇ%ꢃꢌꢄꢅꢑ!ꢊꢑꢌ ꢉ ꢅꢌꢄꢈꢋꢁ
ꢖꢃꢍꢊꢌꢍꢎꢃꢑ ꢗꢉꢍꢎꢄꢌꢈꢌꢐꢋ ꢓꢊꢇ)ꢃꢄꢐ 0ꢚꢒꢝꢀꢀꢀ/
© 2009 Microchip Technology Inc.
DS22226A-page 39
MCP3426/7/8
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
DS22226A-page 40
© 2009 Microchip Technology Inc.
MCP3426/7/8
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆ)"ꢄꢈꢈꢆ*ꢎꢊꢈꢋ+ꢃꢆꢕ)ꢑꢘꢆMꢆꢑꢄ((ꢒ,ꢐꢆꢛ !ꢜꢆ""ꢆ#ꢒꢅ$ꢆ%)*-ꢗ&
ꢑꢒꢊꢃ' 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ*ꢇꢐꢉꢅ"ꢊꢇ)ꢃꢄꢐ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢖꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ*ꢇꢐꢃꢄꢐꢅꢕꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ133)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ*ꢇꢐꢃꢄꢐ
D
e
N
E
E1
NOTE 1
1
2
3
α
h
b
h
c
φ
A2
A
L
A1
L1
β
4ꢄꢃ%
ꢖꢙ55ꢙꢖ,ꢗ,ꢘꢕ
ꢓꢃ&ꢉꢄ ꢃꢌꢄꢅ5ꢃ&ꢃ%
ꢖꢙ6
67ꢖ
ꢖꢔ8
6!&(ꢉꢊꢅꢌ$ꢅꢂꢃꢄ
ꢂꢃ%ꢍꢎ
6
ꢉ
9
ꢀꢁꢏꢜꢅ/ꢕ0
7ꢆꢉꢊꢇꢈꢈꢅ:ꢉꢃꢐꢎ%
ꢔ
M
ꢀꢁꢏ.
ꢚꢁꢀꢚ
M
M
M
ꢀꢁꢜ.
M
ꢚꢁꢏ.
ꢖꢌꢈ"ꢉ"ꢅꢂꢇꢍ*ꢇꢐꢉꢅꢗꢎꢃꢍ*ꢄꢉ
ꢕ%ꢇꢄ"ꢌ$$ꢅꢅ
ꢔꢏ
ꢔꢀ
,
ꢟ
7ꢆꢉꢊꢇꢈꢈꢅ;ꢃ"%ꢎ
>ꢁꢚꢚꢅ/ꢕ0
ꢖꢌꢈ"ꢉ"ꢅꢂꢇꢍ*ꢇꢐꢉꢅ;ꢃ"%ꢎ
7ꢆꢉꢊꢇꢈꢈꢅ5ꢉꢄꢐ%ꢎ
0ꢎꢇ&$ꢉꢊꢅAꢌꢑ%ꢃꢌꢄꢇꢈB
2ꢌꢌ%ꢅ5ꢉꢄꢐ%ꢎ
,ꢀ
ꢓ
ꢎ
+ꢁꢛꢚꢅ/ꢕ0
ꢒꢁꢛꢚꢅ/ꢕ0
ꢚꢁꢏ.
ꢚꢁꢒꢚ
M
M
ꢚꢁ.ꢚ
ꢀꢁꢏꢜ
5
2ꢌꢌ%ꢑꢊꢃꢄ%
2ꢌꢌ%ꢅꢔꢄꢐꢈꢉ
5ꢉꢇ"ꢅꢗꢎꢃꢍ*ꢄꢉ
5ꢉꢇ"ꢅ;ꢃ"%ꢎ
ꢖꢌꢈ"ꢅꢓꢊꢇ$%ꢅꢔꢄꢐꢈꢉꢅꢗꢌꢑ
ꢖꢌꢈ"ꢅꢓꢊꢇ$%ꢅꢔꢄꢐꢈꢉꢅ/ꢌ%%ꢌ&
5ꢀ
ꢀ
ꢀꢁꢚꢒꢅꢘ,2
ꢚꢞ
ꢚꢁꢀꢜ
ꢚꢁ+ꢀ
.ꢞ
M
M
M
M
M
9ꢞ
ꢍ
(
ꢁ
ꢚꢁꢏ.
ꢚꢁ.ꢀ
ꢀ.ꢞ
ꢂ
.ꢞ
ꢀ.ꢞ
ꢑꢒꢊꢃꢉ'
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃ !ꢇꢈꢅꢃꢄ"ꢉ#ꢅ$ꢉꢇ%!ꢊꢉꢅ&ꢇꢋꢅꢆꢇꢊꢋ'ꢅ(!%ꢅ&! %ꢅ(ꢉꢅꢈꢌꢍꢇ%ꢉ"ꢅ)ꢃ%ꢎꢃꢄꢅ%ꢎꢉꢅꢎꢇ%ꢍꢎꢉ"ꢅꢇꢊꢉꢇꢁ
ꢏꢁ ꢟꢅꢕꢃꢐꢄꢃ$ꢃꢍꢇꢄ%ꢅ0ꢎꢇꢊꢇꢍ%ꢉꢊꢃ %ꢃꢍꢁ
+ꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄ ꢅꢓꢅꢇꢄ"ꢅ,ꢀꢅ"ꢌꢅꢄꢌ%ꢅꢃꢄꢍꢈ!"ꢉꢅ&ꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢁꢅꢖꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢅ ꢎꢇꢈꢈꢅꢄꢌ%ꢅꢉ#ꢍꢉꢉ"ꢅꢚꢁꢀ.ꢅ&&ꢅꢑꢉꢊꢅ ꢃ"ꢉꢁ
ꢒꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄꢃꢄꢐꢅꢇꢄ"ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢃꢄꢐꢅꢑꢉꢊꢅꢔꢕꢖ,ꢅ-ꢀꢒꢁ.ꢖꢁ
/ꢕ01 /ꢇ ꢃꢍꢅꢓꢃ&ꢉꢄ ꢃꢌꢄꢁꢅꢗꢎꢉꢌꢊꢉ%ꢃꢍꢇꢈꢈꢋꢅꢉ#ꢇꢍ%ꢅꢆꢇꢈ!ꢉꢅ ꢎꢌ)ꢄꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ ꢁ
ꢘ,21 ꢘꢉ$ꢉꢊꢉꢄꢍꢉꢅꢓꢃ&ꢉꢄ ꢃꢌꢄ'ꢅ! !ꢇꢈꢈꢋꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ'ꢅ$ꢌꢊꢅꢃꢄ$ꢌꢊ&ꢇ%ꢃꢌꢄꢅꢑ!ꢊꢑꢌ ꢉ ꢅꢌꢄꢈꢋꢁ
ꢖꢃꢍꢊꢌꢍꢎꢃꢑ ꢗꢉꢍꢎꢄꢌꢈꢌꢐꢋ ꢓꢊꢇ)ꢃꢄꢐ 0ꢚꢒꢝꢚ.ꢜ/
© 2009 Microchip Technology Inc.
DS22226A-page 41
MCP3426/7/8
ꢀꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆ)"ꢄꢈꢈꢆ*ꢎꢊꢈꢋ+ꢃꢆꢕ)ꢑꢘꢆMꢆꢑꢄ((ꢒ,ꢐꢆꢛ !ꢜꢆ""ꢆ#ꢒꢅ$ꢆ%)*-ꢗ&
ꢑꢒꢊꢃ' 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ*ꢇꢐꢉꢅ"ꢊꢇ)ꢃꢄꢐ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢖꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ*ꢇꢐꢃꢄꢐꢅꢕꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ133)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ*ꢇꢐꢃꢄꢐ
DS22226A-page 42
© 2009 Microchip Technology Inc.
MCP3426/7/8
.ꢜꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢆꢏꢈꢄꢊꢐꢆꢑꢒꢆꢂꢃꢄꢅꢆꢇꢄꢌꢓꢄꢔꢃꢆꢕꢖꢏꢘꢆMꢆꢛꢚꢛꢚꢜ !ꢆ""ꢆ#ꢒꢅ$ꢆ%ꢍꢏꢑ&
ꢑꢒꢊꢃ' 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ*ꢇꢐꢉꢅ"ꢊꢇ)ꢃꢄꢐ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢖꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ*ꢇꢐꢃꢄꢐꢅꢕꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ133)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ*ꢇꢐꢃꢄꢐ
D
e
b
N
N
L
K
E
E2
EXPOSED
PAD
NOTE 1
NOTE 1
2
1
1
2
D2
BOTTOM VIEW
TOP VIEW
A
A1
A3
NOTE 2
4ꢄꢃ%
ꢖꢙ55ꢙꢖ,ꢗ,ꢘꢕ
ꢓꢃ&ꢉꢄ ꢃꢌꢄꢅ5ꢃ&ꢃ%
ꢖꢙ6
67ꢖ
ꢀꢚ
ꢚꢁ.ꢚꢅ/ꢕ0
ꢚꢁꢛꢚ
ꢖꢔ8
6!&(ꢉꢊꢅꢌ$ꢅꢂꢃꢄ
ꢂꢃ%ꢍꢎ
7ꢆꢉꢊꢇꢈꢈꢅ:ꢉꢃꢐꢎ%
ꢕ%ꢇꢄ"ꢌ$$ꢅ
0ꢌꢄ%ꢇꢍ%ꢅꢗꢎꢃꢍ*ꢄꢉ
7ꢆꢉꢊꢇꢈꢈꢅ5ꢉꢄꢐ%ꢎ
,#ꢑꢌ ꢉ"ꢅꢂꢇ"ꢅ5ꢉꢄꢐ%ꢎ
7ꢆꢉꢊꢇꢈꢈꢅ;ꢃ"%ꢎ
6
ꢉ
ꢔ
ꢔꢀ
ꢔ+
ꢓ
ꢓꢏ
,
ꢚꢁ9ꢚ
ꢚꢁꢚꢚ
ꢀꢁꢚꢚ
ꢚꢁꢚ.
ꢚꢁꢚꢏ
ꢚꢁꢏꢚꢅꢘ,2
+ꢁꢚꢚꢅ/ꢕ0
ꢏꢁ+.
+ꢁꢚꢚꢅ/ꢕ0
ꢀꢁ.9
ꢚꢁꢏ.
ꢚꢁꢒꢚ
M
ꢏꢁꢏꢚ
ꢏꢁꢒ9
,#ꢑꢌ ꢉ"ꢅꢂꢇ"ꢅ;ꢃ"%ꢎ
0ꢌꢄ%ꢇꢍ%ꢅ;ꢃ"%ꢎ
0ꢌꢄ%ꢇꢍ%ꢅ5ꢉꢄꢐ%ꢎ
0ꢌꢄ%ꢇꢍ%ꢝ%ꢌꢝ,#ꢑꢌ ꢉ"ꢅꢂꢇ"
,ꢏ
(
5
ꢀꢁꢒꢚ
ꢚꢁꢀ9
ꢚꢁ+ꢚ
ꢚꢁꢏꢚ
ꢀꢁꢜ.
ꢚꢁ+ꢚ
ꢚꢁ.ꢚ
M
=
ꢑꢒꢊꢃꢉ'
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃ !ꢇꢈꢅꢃꢄ"ꢉ#ꢅ$ꢉꢇ%!ꢊꢉꢅ&ꢇꢋꢅꢆꢇꢊꢋ'ꢅ(!%ꢅ&! %ꢅ(ꢉꢅꢈꢌꢍꢇ%ꢉ"ꢅ)ꢃ%ꢎꢃꢄꢅ%ꢎꢉꢅꢎꢇ%ꢍꢎꢉ"ꢅꢇꢊꢉꢇꢁ
ꢏꢁ ꢂꢇꢍ*ꢇꢐꢉꢅ&ꢇꢋꢅꢎꢇꢆꢉꢅꢌꢄꢉꢅꢌꢊꢅ&ꢌꢊꢉꢅꢉ#ꢑꢌ ꢉ"ꢅ%ꢃꢉꢅ(ꢇꢊ ꢅꢇ%ꢅꢉꢄ" ꢁ
+ꢁ ꢂꢇꢍ*ꢇꢐꢉꢅꢃ ꢅ ꢇ)ꢅ ꢃꢄꢐ!ꢈꢇ%ꢉ"ꢁ
ꢒꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄꢃꢄꢐꢅꢇꢄ"ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢃꢄꢐꢅꢑꢉꢊꢅꢔꢕꢖ,ꢅ-ꢀꢒꢁ.ꢖꢁ
/ꢕ01 /ꢇ ꢃꢍꢅꢓꢃ&ꢉꢄ ꢃꢌꢄꢁꢅꢗꢎꢉꢌꢊꢉ%ꢃꢍꢇꢈꢈꢋꢅꢉ#ꢇꢍ%ꢅꢆꢇꢈ!ꢉꢅ ꢎꢌ)ꢄꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ ꢁ
ꢘ,21 ꢘꢉ$ꢉꢊꢉꢄꢍꢉꢅꢓꢃ&ꢉꢄ ꢃꢌꢄ'ꢅ! !ꢇꢈꢈꢋꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ'ꢅ$ꢌꢊꢅꢃꢄ$ꢌꢊ&ꢇ%ꢃꢌꢄꢅꢑ!ꢊꢑꢌ ꢉ ꢅꢌꢄꢈꢋꢁ
ꢖꢃꢍꢊꢌꢍꢎꢃꢑ ꢗꢉꢍꢎꢄꢌꢈꢌꢐꢋ ꢓꢊꢇ)ꢃꢄꢐ 0ꢚꢒꢝꢚ>+/
© 2009 Microchip Technology Inc.
DS22226A-page 43
MCP3426/7/8
.ꢜꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢍꢎꢄꢈꢆꢏꢈꢄꢊꢐꢆꢑꢒꢆꢂꢃꢄꢅꢆꢇꢄꢌꢓꢄꢔꢃꢆꢕꢖꢏꢘꢆMꢆꢛꢚꢛꢚꢜ !ꢆ""ꢆ#ꢒꢅ$ꢆ%ꢍꢏꢑ&
ꢑꢒꢊꢃ' 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ*ꢇꢐꢉꢅ"ꢊꢇ)ꢃꢄꢐ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢖꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ*ꢇꢐꢃꢄꢐꢅꢕꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ133)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ*ꢇꢐꢃꢄꢐ
DS22226A-page 44
© 2009 Microchip Technology Inc.
MCP3426/7/8
.ꢜꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆꢖꢋꢌ(ꢒꢆ)"ꢄꢈꢈꢆ*ꢎꢊꢈꢋ+ꢃꢆꢇꢄꢌꢓꢄꢔꢃꢆꢕ/ꢑꢘꢆ%ꢖ)*ꢇ&
ꢑꢒꢊꢃ' 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ*ꢇꢐꢉꢅ"ꢊꢇ)ꢃꢄꢐ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢖꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ*ꢇꢐꢃꢄꢐꢅꢕꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ133)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ*ꢇꢐꢃꢄꢐ
D
N
E
E1
NOTE 1
1
2
b
e
c
A
A2
φ
L
A1
L1
4ꢄꢃ%
ꢖꢙ55ꢙꢖ,ꢗ,ꢘꢕ
ꢓꢃ&ꢉꢄ ꢃꢌꢄꢅ5ꢃ&ꢃ%
ꢖꢙ6
67ꢖ
ꢖꢔ8
6!&(ꢉꢊꢅꢌ$ꢅꢂꢃꢄ
ꢂꢃ%ꢍꢎ
6
ꢉ
ꢀꢚ
ꢚꢁ.ꢚꢅ/ꢕ0
7ꢆꢉꢊꢇꢈꢈꢅ:ꢉꢃꢐꢎ%
ꢖꢌꢈ"ꢉ"ꢅꢂꢇꢍ*ꢇꢐꢉꢅꢗꢎꢃꢍ*ꢄꢉ
ꢕ%ꢇꢄ"ꢌ$$ꢅ
7ꢆꢉꢊꢇꢈꢈꢅ;ꢃ"%ꢎ
ꢖꢌꢈ"ꢉ"ꢅꢂꢇꢍ*ꢇꢐꢉꢅ;ꢃ"%ꢎ
7ꢆꢉꢊꢇꢈꢈꢅ5ꢉꢄꢐ%ꢎ
2ꢌꢌ%ꢅ5ꢉꢄꢐ%ꢎ
ꢔ
M
ꢚꢁꢜ.
ꢚꢁꢚꢚ
M
ꢚꢁ9.
ꢀꢁꢀꢚ
ꢚꢁꢛ.
ꢚꢁꢀ.
ꢔꢏ
ꢔꢀ
,
,ꢀ
ꢓ
M
ꢒꢁꢛꢚꢅ/ꢕ0
+ꢁꢚꢚꢅ/ꢕ0
+ꢁꢚꢚꢅ/ꢕ0
ꢚꢁ>ꢚ
5
ꢚꢁꢒꢚ
ꢚꢁ9ꢚ
2ꢌꢌ%ꢑꢊꢃꢄ%
2ꢌꢌ%ꢅꢔꢄꢐꢈꢉ
5ꢀ
ꢀ
ꢚꢁꢛ.ꢅꢘ,2
M
ꢚꢞ
9ꢞ
5ꢉꢇ"ꢅꢗꢎꢃꢍ*ꢄꢉ
5ꢉꢇ"ꢅ;ꢃ"%ꢎ
ꢍ
(
ꢚꢁꢚ9
ꢚꢁꢀ.
M
M
ꢚꢁꢏ+
ꢚꢁ++
ꢑꢒꢊꢃꢉ'
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃ !ꢇꢈꢅꢃꢄ"ꢉ#ꢅ$ꢉꢇ%!ꢊꢉꢅ&ꢇꢋꢅꢆꢇꢊꢋ'ꢅ(!%ꢅ&! %ꢅ(ꢉꢅꢈꢌꢍꢇ%ꢉ"ꢅ)ꢃ%ꢎꢃꢄꢅ%ꢎꢉꢅꢎꢇ%ꢍꢎꢉ"ꢅꢇꢊꢉꢇꢁ
ꢏꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄ ꢅꢓꢅꢇꢄ"ꢅ,ꢀꢅ"ꢌꢅꢄꢌ%ꢅꢃꢄꢍꢈ!"ꢉꢅ&ꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢁꢅꢖꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢅ ꢎꢇꢈꢈꢅꢄꢌ%ꢅꢉ#ꢍꢉꢉ"ꢅꢚꢁꢀ.ꢅ&&ꢅꢑꢉꢊꢅ ꢃ"ꢉꢁ
+ꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄꢃꢄꢐꢅꢇꢄ"ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢃꢄꢐꢅꢑꢉꢊꢅꢔꢕꢖ,ꢅ-ꢀꢒꢁ.ꢖꢁ
/ꢕ01 /ꢇ ꢃꢍꢅꢓꢃ&ꢉꢄ ꢃꢌꢄꢁꢅꢗꢎꢉꢌꢊꢉ%ꢃꢍꢇꢈꢈꢋꢅꢉ#ꢇꢍ%ꢅꢆꢇꢈ!ꢉꢅ ꢎꢌ)ꢄꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ ꢁ
ꢘ,21 ꢘꢉ$ꢉꢊꢉꢄꢍꢉꢅꢓꢃ&ꢉꢄ ꢃꢌꢄ'ꢅ! !ꢇꢈꢈꢋꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ'ꢅ$ꢌꢊꢅꢃꢄ$ꢌꢊ&ꢇ%ꢃꢌꢄꢅꢑ!ꢊꢑꢌ ꢉ ꢅꢌꢄꢈꢋꢁ
ꢖꢃꢍꢊꢌꢍꢎꢃꢑ ꢗꢉꢍꢎꢄꢌꢈꢌꢐꢋ ꢓꢊꢇ)ꢃꢄꢐ 0ꢚꢒꢝꢚꢏꢀ/
© 2009 Microchip Technology Inc.
DS22226A-page 45
MCP3426/7/8
.0ꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆ)"ꢄꢈꢈꢆ*ꢎꢊꢈꢋ+ꢃꢆꢕ)ꢂꢘꢆMꢆꢑꢄ((ꢒ,ꢐꢆꢛ !ꢜꢆ""ꢆ#ꢒꢅ$ꢆ%)*-ꢗ&
ꢑꢒꢊꢃ' 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ*ꢇꢐꢉꢅ"ꢊꢇ)ꢃꢄꢐ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢖꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ*ꢇꢐꢃꢄꢐꢅꢕꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ133)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ*ꢇꢐꢃꢄꢐ
D
N
E
E1
NOTE 1
1
2
3
e
h
b
α
h
c
φ
A2
A
L
A1
β
L1
4ꢄꢃ%
ꢖꢙ55ꢙꢖ,ꢗ,ꢘꢕ
ꢓꢃ&ꢉꢄ ꢃꢌꢄꢅ5ꢃ&ꢃ%
ꢖꢙ6
67ꢖ
ꢖꢔ8
6!&(ꢉꢊꢅꢌ$ꢅꢂꢃꢄ
ꢂꢃ%ꢍꢎ
6
ꢉ
ꢀꢒ
ꢀꢁꢏꢜꢅ/ꢕ0
7ꢆꢉꢊꢇꢈꢈꢅ:ꢉꢃꢐꢎ%
ꢖꢌꢈ"ꢉ"ꢅꢂꢇꢍ*ꢇꢐꢉꢅꢗꢎꢃꢍ*ꢄꢉ
ꢕ%ꢇꢄ"ꢌ$$ꢅꢅꢟ
ꢔ
M
ꢀꢁꢏ.
ꢚꢁꢀꢚ
M
M
M
ꢀꢁꢜ.
M
ꢚꢁꢏ.
ꢔꢏ
ꢔꢀ
,
7ꢆꢉꢊꢇꢈꢈꢅ;ꢃ"%ꢎ
>ꢁꢚꢚꢅ/ꢕ0
ꢖꢌꢈ"ꢉ"ꢅꢂꢇꢍ*ꢇꢐꢉꢅ;ꢃ"%ꢎ
7ꢆꢉꢊꢇꢈꢈꢅ5ꢉꢄꢐ%ꢎ
0ꢎꢇ&$ꢉꢊꢅAꢌꢑ%ꢃꢌꢄꢇꢈB
2ꢌꢌ%ꢅ5ꢉꢄꢐ%ꢎ
,ꢀ
ꢓ
ꢎ
+ꢁꢛꢚꢅ/ꢕ0
9ꢁ>.ꢅ/ꢕ0
ꢚꢁꢏ.
ꢚꢁꢒꢚ
M
M
ꢚꢁ.ꢚ
ꢀꢁꢏꢜ
5
2ꢌꢌ%ꢑꢊꢃꢄ%
2ꢌꢌ%ꢅꢔꢄꢐꢈꢉ
5ꢉꢇ"ꢅꢗꢎꢃꢍ*ꢄꢉ
5ꢉꢇ"ꢅ;ꢃ"%ꢎ
ꢖꢌꢈ"ꢅꢓꢊꢇ$%ꢅꢔꢄꢐꢈꢉꢅꢗꢌꢑ
ꢖꢌꢈ"ꢅꢓꢊꢇ$%ꢅꢔꢄꢐꢈꢉꢅ/ꢌ%%ꢌ&
5ꢀ
ꢀ
ꢀꢁꢚꢒꢅꢘ,2
ꢚꢞ
ꢚꢁꢀꢜ
ꢚꢁ+ꢀ
.ꢞ
M
M
M
M
M
9ꢞ
ꢍ
(
ꢁ
ꢚꢁꢏ.
ꢚꢁ.ꢀ
ꢀ.ꢞ
ꢂ
.ꢞ
ꢀ.ꢞ
ꢑꢒꢊꢃꢉ'
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃ !ꢇꢈꢅꢃꢄ"ꢉ#ꢅ$ꢉꢇ%!ꢊꢉꢅ&ꢇꢋꢅꢆꢇꢊꢋ'ꢅ(!%ꢅ&! %ꢅ(ꢉꢅꢈꢌꢍꢇ%ꢉ"ꢅ)ꢃ%ꢎꢃꢄꢅ%ꢎꢉꢅꢎꢇ%ꢍꢎꢉ"ꢅꢇꢊꢉꢇꢁ
ꢏꢁ ꢟꢅꢕꢃꢐꢄꢃ$ꢃꢍꢇꢄ%ꢅ0ꢎꢇꢊꢇꢍ%ꢉꢊꢃ %ꢃꢍꢁ
+ꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄ ꢅꢓꢅꢇꢄ"ꢅ,ꢀꢅ"ꢌꢅꢄꢌ%ꢅꢃꢄꢍꢈ!"ꢉꢅ&ꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢁꢅꢖꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢅ ꢎꢇꢈꢈꢅꢄꢌ%ꢅꢉ#ꢍꢉꢉ"ꢅꢚꢁꢀ.ꢅ&&ꢅꢑꢉꢊꢅ ꢃ"ꢉꢁ
ꢒꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄꢃꢄꢐꢅꢇꢄ"ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢃꢄꢐꢅꢑꢉꢊꢅꢔꢕꢖ,ꢅ-ꢀꢒꢁ.ꢖꢁ
/ꢕ01 /ꢇ ꢃꢍꢅꢓꢃ&ꢉꢄ ꢃꢌꢄꢁꢅꢗꢎꢉꢌꢊꢉ%ꢃꢍꢇꢈꢈꢋꢅꢉ#ꢇꢍ%ꢅꢆꢇꢈ!ꢉꢅ ꢎꢌ)ꢄꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ ꢁ
ꢘ,21 ꢘꢉ$ꢉꢊꢉꢄꢍꢉꢅꢓꢃ&ꢉꢄ ꢃꢌꢄ'ꢅ! !ꢇꢈꢈꢋꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ'ꢅ$ꢌꢊꢅꢃꢄ$ꢌꢊ&ꢇ%ꢃꢌꢄꢅꢑ!ꢊꢑꢌ ꢉ ꢅꢌꢄꢈꢋꢁ
ꢖꢃꢍꢊꢌꢍꢎꢃꢑ ꢗꢉꢍꢎꢄꢌꢈꢌꢐꢋ ꢓꢊꢇ)ꢃꢄꢐ 0ꢚꢒꢝꢚ>./
DS22226A-page 46
© 2009 Microchip Technology Inc.
MCP3426/7/8
ꢑꢒꢊꢃ' 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ*ꢇꢐꢉꢅ"ꢊꢇ)ꢃꢄꢐ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢖꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ*ꢇꢐꢃꢄꢐꢅꢕꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ133)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ*ꢇꢐꢃꢄꢐ
© 2009 Microchip Technology Inc.
DS22226A-page 47
MCP3426/7/8
.0ꢁꢂꢃꢄꢅꢆꢇꢈꢄꢉꢊꢋꢌꢆ12ꢋ+ꢆ)2(ꢋ+ꢓꢆ)"ꢄꢈꢈꢆ*ꢎꢊꢈꢋ+ꢃꢆꢕ)1ꢘꢆMꢆ0 0ꢆ""ꢆ#ꢒꢅ$ꢆ%1))*ꢇ&
ꢑꢒꢊꢃ' 2ꢌꢊꢅ%ꢎꢉꢅ&ꢌ %ꢅꢍ!ꢊꢊꢉꢄ%ꢅꢑꢇꢍ*ꢇꢐꢉꢅ"ꢊꢇ)ꢃꢄꢐ 'ꢅꢑꢈꢉꢇ ꢉꢅ ꢉꢉꢅ%ꢎꢉꢅꢖꢃꢍꢊꢌꢍꢎꢃꢑꢅꢂꢇꢍ*ꢇꢐꢃꢄꢐꢅꢕꢑꢉꢍꢃ$ꢃꢍꢇ%ꢃꢌꢄꢅꢈꢌꢍꢇ%ꢉ"ꢅꢇ%ꢅ
ꢎ%%ꢑ133)))ꢁ&ꢃꢍꢊꢌꢍꢎꢃꢑꢁꢍꢌ&3ꢑꢇꢍ*ꢇꢐꢃꢄꢐ
D
N
E
E1
NOTE 1
1
2
e
b
c
φ
A2
A
A1
L
L1
4ꢄꢃ%
ꢖꢙ55ꢙꢖ,ꢗ,ꢘꢕ
ꢓꢃ&ꢉꢄ ꢃꢌꢄꢅ5ꢃ&ꢃ%
ꢖꢙ6
67ꢖ
ꢖꢔ8
6!&(ꢉꢊꢅꢌ$ꢅꢂꢃꢄ
ꢂꢃ%ꢍꢎ
6
ꢉ
ꢀꢒ
ꢚꢁ>.ꢅ/ꢕ0
7ꢆꢉꢊꢇꢈꢈꢅ:ꢉꢃꢐꢎ%
ꢖꢌꢈ"ꢉ"ꢅꢂꢇꢍ*ꢇꢐꢉꢅꢗꢎꢃꢍ*ꢄꢉ
ꢕ%ꢇꢄ"ꢌ$$ꢅ
7ꢆꢉꢊꢇꢈꢈꢅ;ꢃ"%ꢎ
ꢖꢌꢈ"ꢉ"ꢅꢂꢇꢍ*ꢇꢐꢉꢅ;ꢃ"%ꢎ
ꢖꢌꢈ"ꢉ"ꢅꢂꢇꢍ*ꢇꢐꢉꢅ5ꢉꢄꢐ%ꢎ
2ꢌꢌ%ꢅ5ꢉꢄꢐ%ꢎ
ꢔ
M
ꢚꢁ9ꢚ
ꢚꢁꢚ.
M
ꢀꢁꢚꢚ
M
>ꢁꢒꢚꢅ/ꢕ0
ꢒꢁꢒꢚ
.ꢁꢚꢚ
ꢚꢁ>ꢚ
ꢀꢁꢏꢚ
ꢀꢁꢚ.
ꢚꢁꢀ.
ꢔꢏ
ꢔꢀ
,
,ꢀ
ꢓ
ꢒꢁ+ꢚ
ꢒꢁꢛꢚ
ꢚꢁꢒ.
ꢒꢁ.ꢚ
.ꢁꢀꢚ
ꢚꢁꢜ.
5
2ꢌꢌ%ꢑꢊꢃꢄ%
2ꢌꢌ%ꢅꢔꢄꢐꢈꢉ
5ꢉꢇ"ꢅꢗꢎꢃꢍ*ꢄꢉ
5ꢉꢇ"ꢅ;ꢃ"%ꢎ
5ꢀ
ꢀ
ꢀꢁꢚꢚꢅꢘ,2
ꢚꢞ
ꢚꢁꢚꢛ
ꢚꢁꢀꢛ
M
M
M
9ꢞ
ꢍ
(
ꢚꢁꢏꢚ
ꢚꢁ+ꢚ
ꢑꢒꢊꢃꢉ'
ꢀꢁ ꢂꢃꢄꢅꢀꢅꢆꢃ !ꢇꢈꢅꢃꢄ"ꢉ#ꢅ$ꢉꢇ%!ꢊꢉꢅ&ꢇꢋꢅꢆꢇꢊꢋ'ꢅ(!%ꢅ&! %ꢅ(ꢉꢅꢈꢌꢍꢇ%ꢉ"ꢅ)ꢃ%ꢎꢃꢄꢅ%ꢎꢉꢅꢎꢇ%ꢍꢎꢉ"ꢅꢇꢊꢉꢇꢁ
ꢏꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄ ꢅꢓꢅꢇꢄ"ꢅ,ꢀꢅ"ꢌꢅꢄꢌ%ꢅꢃꢄꢍꢈ!"ꢉꢅ&ꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢁꢅꢖꢌꢈ"ꢅ$ꢈꢇ ꢎꢅꢌꢊꢅꢑꢊꢌ%ꢊ! ꢃꢌꢄ ꢅ ꢎꢇꢈꢈꢅꢄꢌ%ꢅꢉ#ꢍꢉꢉ"ꢅꢚꢁꢀ.ꢅ&&ꢅꢑꢉꢊꢅ ꢃ"ꢉꢁ
+ꢁ ꢓꢃ&ꢉꢄ ꢃꢌꢄꢃꢄꢐꢅꢇꢄ"ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢃꢄꢐꢅꢑꢉꢊꢅꢔꢕꢖ,ꢅ-ꢀꢒꢁ.ꢖꢁ
/ꢕ01 /ꢇ ꢃꢍꢅꢓꢃ&ꢉꢄ ꢃꢌꢄꢁꢅꢗꢎꢉꢌꢊꢉ%ꢃꢍꢇꢈꢈꢋꢅꢉ#ꢇꢍ%ꢅꢆꢇꢈ!ꢉꢅ ꢎꢌ)ꢄꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ ꢁ
ꢘ,21 ꢘꢉ$ꢉꢊꢉꢄꢍꢉꢅꢓꢃ&ꢉꢄ ꢃꢌꢄ'ꢅ! !ꢇꢈꢈꢋꢅ)ꢃ%ꢎꢌ!%ꢅ%ꢌꢈꢉꢊꢇꢄꢍꢉ'ꢅ$ꢌꢊꢅꢃꢄ$ꢌꢊ&ꢇ%ꢃꢌꢄꢅꢑ!ꢊꢑꢌ ꢉ ꢅꢌꢄꢈꢋꢁ
ꢖꢃꢍꢊꢌꢍꢎꢃꢑ ꢗꢉꢍꢎꢄꢌꢈꢌꢐꢋ ꢓꢊꢇ)ꢃꢄꢐ 0ꢚꢒꢝꢚ9ꢜ/
DS22226A-page 48
© 2009 Microchip Technology Inc.
MCP3426/7/8
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
© 2009 Microchip Technology Inc.
DS22226A-page 49
MCP3426/7/8
NOTES:
DS22226A-page 50
© 2009 Microchip Technology Inc.
MCP3426/7/8
APPENDIX A: REVISION HISTORY
Revision A (December 2009)
• Original Release of this Document.
© 2009 Microchip Technology Inc.
DS22226A-page 51
MCP3426/7/8
NOTES:
DS22226A-page 52
© 2009 Microchip Technology Inc.
MCP3426/7/8
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
Examples:
PART NO.
Device
-X
/XX
a)
MCP3426A0-E/MC: 2-Channel ADC,
Temperature Package
Range
8LD DFN package.
MCP3426A0T-E/MC: Tape and Reel,
2-Channel ADC,
b)
8LD DFN package.
Device:
MCP3426: 2-Channel 16-Bit ADC
MCP3426T: 2-Channel 16-Bit ADC
(Tape and Reel)
MCP3427: 2-Channel 16-Bit ADC
MCP3427T: 2-Channel 16-Bit ADC
(Tape and Reel)
MCP3428: 4-Channel 16-Bit ADC
MCP3428T: 4-Channel 16-Bit ADC
(Tape and Reel)
c)
d)
MCP3426A0-E/MS: 2-Channel ADC,
8LD MSOP package.
MCP3426A0T-E/MS: Tape and Reel,
2-Channel ADC,
8LD MSOP package.
e)
f)
MCP3426A0-E/SN: 2-Channel ADC,
8LD SOIC package.
MCP3426A0T-E/SN: Tape and Reel,
2-Channel ADC,
Temperature Range:
Package:
E
=
-40°C to +125°C
8LD SOIC package.
a)
b)
MCP3427-E/MF:
MCP3427T-E/MF:
2-Channel ADC,
10LD DFN package.
Tape and Reel,
2-Channel ADC,
10LD DFN package.
2-Channel ADC,
MC
MS
SN
MF
UN
SL
=
=
=
=
=
=
=
Plastic Dual Flat, No Lead (2x3 DFN), 8-lead
Plastic Micro Small Outline (MSOP), 8-lead
Plastic Small Outline SOIC, 8-lead
Plastic Dual Flat, No Lead (3x3 DFN) 10-lead
Plastic Micro Small Outline (MSOP), 10-lead
Plastic Small Outline SOIC (150 mil Body), 14-lead
Plastic TSSOP (4.4mm Body), 14-lead
ST
c)
d)
MCP3427-E/UN:
MCP3427T-E/UN:
10LD MSOP package.
Tape and Reel,
2-Channel ADC,
10LD MSOP package.
a)
b)
MCP3428-E/SL:
MCP3428T-E/SL:
4-Channel ADC,
14LD SOIC package.
Tape and Reel,
4-Channel ADC,
14LD SOIC package.
4-Channel ADC,
14LD TSSOP package.
Tape and Reel,
c)
d)
MCP3428-E/ST:
MCP3428T-E/ST:
4-Channel ADC,
14LD TSSOP package.
© 2009 Microchip Technology Inc.
DS22226A-page 53
MCP3426/7/8
NOTES:
DS22226A-page 54
© 2009 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,
rfPIC and UNI/O are registered trademarks of Microchip
Technology Incorporated in the U.S.A. and other countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MXDEV, MXLAB, SEEVAL and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified
logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, PIC32 logo, REAL ICE, rfLAB, Select Mode, Total
Endurance, TSHARC, UniWinDriver, WiperLock and ZENA
are trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2009, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
© 2009 Microchip Technology Inc.
DS22226A-page 55
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4080
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Boston
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Korea - Seoul
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Cleveland
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Detroit
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-6578-300
Fax: 886-3-6578-370
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Santa Clara
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
03/26/09
DS22226A-page 56
© 2009 Microchip Technology Inc.
相关型号:
MCP3427-ESN
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference
MAXIM
MCP3427-EST
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference
MAXIM
MCP3427-EUN
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference
MAXIM
MCP3427T-EMC
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference
MAXIM
MCP3427T-EMF
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference
MAXIM
MCP3427T-EMS
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference
MAXIM
MCP3427T-ESL
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference
MAXIM
MCP3427T-ESN
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference
MAXIM
MCP3427T-EST
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference
MAXIM
MCP3427T-EUN
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference
MAXIM
MCP3428
16-Bit, Multi-Channel Analog-to-Digital Converter with I2C Interface and On-Board Reference
MAXIM
MCP3428-E/SL
4-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO14, 3.90 MM, LEAD FREE, PLASTIC, SOIC-14
MICROCHIP
©2020 ICPDF网 联系我们和版权申明