ES1GP [MCC]
DIODE 1 A, 400 V, SILICON, SIGNAL DIODE, DO-214AC, PLASTIC, HSMA, 2 PIN, Signal Diode;型号: | ES1GP |
厂家: | Micro Commercial Components |
描述: | DIODE 1 A, 400 V, SILICON, SIGNAL DIODE, DO-214AC, PLASTIC, HSMA, 2 PIN, Signal Diode |
文件: | 总4页 (文件大小:118K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
M C C
ES1A
THRU
ES1M
TM
ꢀꢁꢂꢃꢄꢅꢆꢄꢇꢇꢈꢃꢂꢁꢉꢊꢅꢆomponents
20736 Marilla Street Chatsworth
ꢆꢋꢅꢌꢍꢎꢍꢍ
ꢏꢐꢄꢑꢈꢒꢅꢓꢔꢍꢔ ꢅ!ꢕꢍ"#ꢌꢎꢎ
$ꢉ%ꢒꢅ ꢅ ꢅ ꢓꢔꢍꢔ ꢅ!ꢕꢍ"#ꢌꢎꢌ
Micro Commercial Components
1 Amp Super Fast
Recovery
Features
x
Case Material: Molded Plastic. UL Flammability
Classification Rating 94V-0
Silicon Rectifier
50 to 1000 Volts
x
x
High Temp Soldering: 260qC for 10 Seconds At Terminals
Superfast Recovery Times For High Efficiency
Maximum Ratings
x
x
x
Operating Temperature: -50qC to +150qC
Storage Temperature: -50qC to +150qC
Maximum Thermal Resistance; 15qC/W Junction To Lead
DO-214AC
(HSMA) (High Profile)
MCC
Part
Number
Maximum
Recurrent
Marking Peak Reverse
Voltage
Maximum
RMS
Voltage
Maximum
DC
Blocking
Voltage
50V
H
Device
Cathode Band
J
ES1A
ES1B
ES1C
ES1D
ES1G
ES1J
ES1K
ES1M
ES1A
ES1B
ES1C
ES1D
ES1G
ES1J
ES1K
ES1M
50V
100V
150V
200V
400V
600V
800V
1000V
35V
70V
100V
150V
105V
140V
280V
420V
560V
700V
200V
400V
A
C
600V
800V
1000V
E
D
B
F
G
Electrical Characteristics @ 25qC Unless Otherwise Specified
Average Forward
Current
IF(AV)
1.0A
Ta = 75qC
DIMENSIONS
INCHES
MIN
.078
.067
.002
---
MM
MIN
Peak Forward Surge
Current
Maximum
Instantaneous
Forward Voltage
ES1A-D
ES1G-J
ES1K~M
Maximum DC
Reverse Current At
Rated DC Blocking
Voltage
IFSM
30A
8.3ms, half sine
DIM
A
MAX
.116
.089
.008
.02
MAX
2.95
2.25
.20
NOTE
1.98
1.70
.05
B
C
D
E
---
.51
.035
.065
.205
.160
.100
.055
.096
.224
.180
.112
.89
1.40
2.45
5.69
4.57
2.84
F
1.65
5.21
4.06
2.57
G
H
J
VF
.975V
1.35V
1.70V
IFM = 1.0A;
TJ = 25qC*
SUGGESTED SOLDER
PAD LAYOUT
IR
5PA
TJ = 25qC
0.090”
100PA TJ = 100qC
Maximum Reverse
Recovery Time
ES1A-D
0.085”
Trr
CJ
50ns
75ns
100ns
IF=0.5A, IR=1.0A,
Irr=0.25A
ES1G-K
ES1M
0.070”
Typical Junction
Capacitance
45pF
Measured at
1.0MHz, VR=4.0V
*Pulse test: Pulse width 200 Psec, Duty cycle 2%
www.mccsemi.com
Revision: 7
2007/06/19
1 of 4
ES1A thru ES1M
M C C
TM
Figure 1
Typical Forward Characteristics
Micro Commercial Components
Figure 2
Forward Derating Curve
2.4
2.2
2.0
50
ES1A~ES1D
10
ES1G~ES1J
1.8
1.6
1.4
3.0
ES1K~ES1M
1.0
1.2
Amps
1.0
.8
.6
0.1
.01
.4
.2
Single Phase, Half Wave
60Hz Resistive or Inductive Load
0
25
50
75
100
125
150
0
.6
.8 1.0 1.2 1.4 1.6 1.8 2.0
FORWARD VOLTAGE,(V)
°C
Average Forward Rectified Current - Amperesversus
Ambient Temperature -°C
Instantaneous Forward Current - Amperesversus
Instantaneous Forward Voltage - Volts
Figure 3
Junction Capacitance
100
60
40
20
TJ=25°C;f=1MHZ
pF
10
6
4
2
1
400
1000
.1
.2
.4
1
2
10 20
200
4
40
100
Volts
Junction Capacitance - pFversus
Reverse Voltage - Volts
www.mccsemi.com
Revision: 7
2007/06/19
2 of 4
M C C
TM
ES1A thru ES1M
Micro Commercial Components
Figure 5
Typical Reverse Characteristics
Figure 4
Peak Forward Surge Current
100
30
25
Tj = 100°C
20
15
10
Amps
10
5
0
1.0
0.1
Tj = 25°C
80
100
1
6
60
4
10 20
40
8
2
Cycles
Peak Forward Surge Current - Amperesversus
Number Of Cycles At 60Hz - Cycles
0
40
80
120
PERCENT OF RATED PEAK REVERSE VOLTAGE (%)
Figure 6
Reverse Recovery Time Characteristic And Test Circuit Diagram
50Ω
10Ω
trr
+0.5A
0
-0.25
Pulse
Generator
Note 2
25Vdc
-1.0
Oscilloscope
Note 1
1Ω
1cm
Set Time Base for 20/100ns/cm
Notes:
1. Rise Time = 7ns max.
Input impedance = 1 megohm, 22pF
2. Rise Time = 10ns max.
Source impedance = 50 ohms
3. Resistors are non-inductive
Figure 7
New SMA Assembly
Round Lead
Process
www.mccsemi.com
3 of 4
Revision: 7
2007/06/19
M C C
TM
Micro Commercial Components
***IMPORTANT NOTICE***
Micro Commercial Components Corp . reserves the right to make changes without further notice to any
product herein to make corrections, modifications , enhancements , improvements , or other changes .
Micro Commercial Components Corp . does not assume any liability arising out of the application or
use of any product described herein; neither does it convey any license under its patent rights ,nor
the rights of others . The user of products in such applications shall assume all risks of such use
and will agree to hold Micro Commercial Components Corp . and all the companies whose
products are represented on our website, harmless against all damages.
***APPLICATIONS DISCLAIMER***
Products offer by Micro Commercial Components Corp . are not intended for use in Medical,
Aerospace or Military Applications.
www.mccsemi.com
4 of 4
Revision: 7
2007/06/19
相关型号:
©2020 ICPDF网 联系我们和版权申明