MAX825SEUK [MICREL]
Voltage Supervisor with Watchdog Timer and Manual Reset;型号: | MAX825SEUK |
厂家: | MICREL SEMICONDUCTOR |
描述: | Voltage Supervisor with Watchdog Timer and Manual Reset 信息通信管理 光电二极管 |
文件: | 总14页 (文件大小:957K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MAX823/4/5
Voltage Supervisor with Watchdog Timer
and Manual Reset
Revision 1.0
Features
General Description
Precision 1.665V to 4.625V power supply monitor
±0.5% threshold accuracy at TA = +25°C
±1.5% threshold accuracy from TA = –40°C to +125°C
3.8µA supply current (S,R,T,W,Y,Z options)
4.8µA supply current (L,M options)
Manual reset input (MAX823/5)
140ms (min.) reset timeout period
1.6s (typ.) watchdog timeout period
The MAX823/4/5 voltage supervisory circuits combine
low-current, manual reset input, watchdog timer, active-
high and active-low push-pull outputs. The reset outputs
are asserted and held when the supply voltage falls below
the factory-programmed threshold voltage, when the /MR
pin is pulled low, or if the watchdog times out. Reset is
asserted for the reset timeout delay after the supply
voltage increases above the rising threshold voltage or
when manual reset input is asserted high.
Active-high and active-low push-pull outputs
Guaranteed reset output valid to VCC = 1V
40°C to +125°C junction temperature range
5-pin SOT23 & SC70 packages
The MAX823/4/5 features an integrated pull-up resistor on
the /MR pin. An active-low push-pull reset output (/RESET)
and an active-high reset output (RESET) provide flexibility
when interfacing with various microcontrollers, PMICs, or
load switches. The watchdog input can be left
unconnected for applications that do not require watchdog
monitoring.
8x lower watchdog input current than competition
Applications
The MAX823/4/5 consumes a quiescent current of only
3.8µA and is offered in standard SOT23-5 and SC70-5
packages. It is rated for the –40°C to +125°C temperature
range.
Computers and Controllers
Embedded Controllers
Intelligent Instruments
Automotive Systems
Datasheets and support documentation are available on
Micrel’s web site at: www.micrel.com.
Critical µP Monitoring
Portable/ Battery-Powered Equipment
Typical Application
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
Revision 1.0
January 14, 2014
Micrel, Inc.
MAX823/4/5
FUNCTION
MAX823
MAX824
MAX825
Active-Low Reset
Active-High Reset
Watchdog Input
−
−
−
Manual Reset Input
Ordering Information(1)
VRST: Nominal Threshold
Voltage (V)
Part Number
Top Marking
X3L
Package
MAX823LEUK
MAX823MEUK
MAX823REUK
MAX823SEUK
MAX823TEUK
MAX823WEUK
MAX823YEUK
MAX823ZEUK
MAX823LEXK
MAX823MEXK
MAX823REXK
MAX823SEXK
MAX823TEXK
MAX823WEXK
MAX823YEXK
MAX823ZEXK
4.625
4.375
2.625
2.925
3.075
1.665
2.188
2.315
4.625
4.375
2.625
2.925
3.075
1.665
2.188
2.315
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
X3M
X3R
X3S
X3T
X3W
X3Y
X3Z
XA
XB
XF
XE
XC
XL
XK
XJ
Revision 1.0
January 14, 2014
2
Micrel, Inc.
MAX823/4/5
Ordering Information (Continued)(1)
VRST: Nominal Threshold
Voltage (V)
Part Number
Top Marking
Package
MAX824LEUK
MAX824MEUK
MAX824REUK
MAX824SEUK
MAX824TEUK
MAX824WEUK
MAX824YEUK
MAX824ZEUK
MAX824LEXK
MAX824MEXK
MAX824REXK
MAX824SEXK
MAX824TEXK
MAX824WEXK
MAX824YEXK
MAX824ZEXK
X4L
X4M
X4R
X4S
X4T
X4W
X4Y
X4Z
4Y
4.625
4.375
2.625
2.925
3.075
1.665
2.188
2.315
4.625
4.375
2.625
2.925
3.075
1.665
2.188
2.315
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
YA
YD
YC
YB
YG
YF
YE
VRST: Nominal Threshold
Voltage (V)
Part Number
Top Marking
Package
MAX825LEUK
MAX825MEUK
MAX825REUK
MAX825SEUK
MAX825TEUK
MAX825WEUK
MAX825YEUK
MAX825ZEUK
MAX825LEXK
MAX825MEXK
MAX825REXK
MAX825SEXK
MAX825TEXK
MAX825WEXK
MAX825YEXK
MAX825ZEXK
Note:
X5L
X5M
X5R
X5S
X5T
X5W
X5Y
X5Z
YE
4.625
4.375
2.625
2.925
3.075
1.665
2.188
2.315
4.625
4.375
2.625
2.925
3.075
1.665
2.188
2.315
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SOT23-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
SC70-5
YI
YO
YK
YJ
YT
YS
YR
1. All devices are available in tape-and-reel only. Contact Micrel for tape-and-reel options.
Revision 1.0
January 14, 2014
3
Micrel, Inc.
MAX823/4/5
Pin Configuration
MAX823
MAX824
SOT23(EUK) &SC70(EXK)
Top View
MAX825
SOT23(EUK) &SC70(EXK)
Top View
SOT23(EUK) &SC70(EXK)
Top View
Pin Description
Pin Number
MAX823
Pin Number
MAX824
Pin Number
MAX825
Pin Name Pin Function
Active-Low Reset Output. Pulses low for 200ms when triggered, and
remains low whenever VCC is below the reset threshold or when /MR is
a logic low. It remains low for 200ms after one of the following occurs:
VCC rises above the reset threshold, the watchdog triggers a reset, or
/MR goes low to high.
1
2
-
1
2
3
1
2
3
/RESET
GND
Ground.
Active-High Reset Output. Pulses high for 200ms when triggered, and
remains high whenever VCC is below the reset threshold or when /MR
is a logic low. It remains high for 200ms after one of the following
occurs: VCC rises above the reset threshold, the watchdog triggers a
reset, or /MR goes low to high. RESET is the inverse of /RESET.
RESET
Watchdog Input. If WDI remains either high or low for longer than the
watchdog timeout period, the internal watchdog timer runs out and a
reset is triggered. The internal watchdog timer clears whenever reset
is asserted, or whenever WDI sees a rising or falling edge. If WDI is
left unconnected or is connected to a three-stated buffer output, the
watchdog feature is disabled.
4
3
4
-
-
WDI
/MR
Manual Reset Input. A logic low on /MR asserts reset. Reset remains
asserted as long as /MR is held low and for 200ms after /MR returns
high. The active-low input has an internal 52kΩ pull-up resistor. It can
be driven from a CMOS logic line or shorted to ground with a switch.
Leave open or connect to VCC if unused.
4
Supply Voltage Pin. VCC is the input to the supply voltage monitor.
When the supply voltage falls below the reset threshold voltage, reset
outputs (/RESET and RESET) are triggered immediately. When the
supply voltage rises above the reset threshold plus hysteresis voltage,
the reset outputs remain asserted for the duration of the reset timeout
period. An optional 0.1µF bypass capacitor mounted close to VCC
provides additional transient immunity.
5
5
5
VCC
Revision 1.0
January 14, 2014
4
Micrel, Inc.
MAX823/4/5
Absolute Maximum Ratings(2)
Operating Ratings(3)
Supply Voltage (VCC).................................... +1.0V to +5.5V
Watchdog Input (WDI)...........................................0V to VCC
Junction Temperature (TJ) ........................–40°C to +125°C
Junction Thermal Resistance
Supply Voltage (VCC).................................... 0.3V to 6.0V
/MR, WDI, RESET, /RESET.................. 0.3V to VCC +0.3V
Input Current (All Pins except RESET, /RESET)........20mA
Output Current (RESET, /RESET)..............................20mA
Junction Temperature (TJ) ........................40°C to +150°C
Storage Temperature (Ts).........................65°C to +150°C
ESD Rating(4) (Human Body Model)(MAX823/4/5) ........3kV
5-Pin SOT23....................................................215°C/W
5-Pin SC70 ......................................................250°C/W
Electrical Characteristics(5)
VCC = 4.7V to 5.5V for MAX823/4/5L, VCC = 4.5V to 5.5V for MAX823/4/5M, VCC = 3.15V to 3.6V for MAX823/4/5T, VCC = 3.0V to 3.6V
for MAX823/4/5S, VCC = 2.7V to 3.6V for MAX823/4/5R, VCC = 2.38V to 2.75V for MAX823/4/5Z, VCC = 2.25V to 2.75V for
MAX823/4/5Y, VCC = 1.75V to 2.0V for MAX823/4/5W; TJ = +25˚C, bold values(6) indicate –40˚C ≤ TJ ≤ +125˚C, unless otherwise noted.
Parameter
Condition
Min.
Typ.
Max.
Units
Power Suppy Input
1.0
5.5
14
Supply Voltage (VCC
)
V
L/M (WDI and /MR unconnected)
4.8
3.8
µA
µA
Supply Current (IVCC
)
8.4
T/S/R/Z/Y/W (WDI and /MR unconnected)
Reset Threshold Voltage
4.602
4.556
4.353
4.309
3.060
3.029
2.910
2.881
2.612
2.586
2.303
2.280
2.177
2.155
1.657
1.640
4.625
4.375
3.075
2.925
2.625
2.315
2.188
1.665
4.648
4.694
4.397
4.441
3.090
3.121
2.940
2.969
2.638
2.664
2.327
2.350
2.199
2.221
1.673
1.690
V
L (falling) TA = 25C
V
L (falling) 40C TA +125C
M (falling) TA = 25C
V
V
M (falling) –40C TA +125C
T (falling) TA = 25C
V
V
T (falling) –40C TA +125C
S (falling) TA = 25C
V
V
S (falling) –40C TA +125C
R (falling) TA = 25C
Reset Threshold Voltage
(VRST
)
V
V
R (falling) –40C TA +125C
Z (falling) TA = 25C
V
V
V
Z (falling) –40C TA +125C
Y (falling) TA = 25C
V
Y (falling) –40C TA +125C
W (falling) TA = 25C
V
V
W (falling) –40C TA +125C
L, M
10
5
mV
mV
ppm/˚C
Reset Threshold
Hysteresis
T, S, R, Z, Y, W
Reset Threshold Tempco
40
Revision 1.0
January 14, 2014
5
Micrel, Inc.
MAX823/4/5
Electrical Characteristics (Continued)(5)
VCC = 4.7V to 5.5V for MAX823/4/5L, VCC = 4.5V to 5.5V for MAX823/4/5M, VCC = 3.15V to 3.6V for MAX823/4/5T, VCC = 3.0V to 3.6V
for MAX823/4/5S, VCC = 2.7V to 3.6V for MAX823/4/5R, VCC = 2.38V to 2.75V for MAX823/4/5Z, VCC = 2.25V to 2.75V for
MAX823/4/5Y, VCC = 1.75V to 2.0V for MAX823/4/5W; TJ = +25˚C, bold values(6) indicate –40˚C ≤ TJ ≤ +125˚C, unless otherwise noted.
Parameter
Condition
Min.
140
Typ.
Max.
280
Units
Reset Timeout Period
200
ms
(tRP
)
Reset Time
VCC to /RESET Delay
10
µs
(tRD
Reset Outputs (/RESET, RESET)
L, M: VCC VRST (MAX), ISOURCE = 120µA
)
VCC – 1.5
0.8 × VCC
0.8 × VCC
V
V
/RESET Output Voltage
High (VOH
T, S, R, Z, Y: VCC VRST (MAX)
,
)
ISOURCE = 30µA
V
V
W: VCC VRST (MAX), ISOURCE = 20µA
L, M: VCC VRST (MIN), ISINK = 3.2mA
0.4
0.3
T, S, R, Z, Y, W: VCC VRST (MIN)
ISINK = 1.2mA
,
V
/RESET Output Voltage
Low (VOL
)
0.3
0.3
TA = 0˚C to +70˚C, VCC = 1V, ISINK =50µA
VCC = 1.2V, ISINK =100µA
V
V
800
L, M: /RESET = 0V, VCC = 5.5V
µA
/RESET Output Short-
Circuit Current(7)
T, S, R, Z, Y, W: /RESET = 0V,
VCC = 3.6V
400
µA
RESET Output Voltage
0.8 × VCC
V
V
V
VCC 1.6VISOURCE = 150µA
High (VOH
)
0.4
0.3
L, M: VCC VRST (MAX), ISINK = 3.2mA
RESET Output Voltage
Low (VOL
T, S, R, Z, Y, W: VCC VRST (MAX)
ISINK = 1.2mA
,
)
Watchdog Input (WDI)(8)
Watchdog Timeout
1.12
50
2.40
1.60
s
ns
V
Period (tWD
)
Watchdog Pulse Width
0.3 ×
VCC
Watchdog Input Low
Voltage (VIL)
Watchdog Input High
Voltage (VIH)
0.7 × VCC
-20
V
25
WDI = VCC
WDI = 0V
15
µA
µA
Watchdog Input Current
-15
Revision 1.0
January 14, 2014
6
Micrel, Inc.
MAX823/4/5
Electrical Characteristics (Continued)(5)
VCC = 4.7V to 5.5V for MAX823/4/5L, VCC = 4.5V to 5.5V for MAX823/4/5M, VCC = 3.15V to 3.6V for MAX823/4/5T, VCC = 3.0V to 3.6V
for MAX823/4/5S, VCC = 2.7V to 3.6V for MAX823/4/5R, VCC = 2.38V to 2.75V for MAX823/4/5Z, VCC = 2.25V to 2.75V for
MAX823/4/5Y, VCC = 1.75V to 2.0V for MAX823/4/5W; TJ = +25˚C, bold values(6) indicate –40˚C ≤ TJ ≤ +125˚C, unless otherwise noted.
Parameter
Condition
Min.
Typ.
Max.
Units
Manual Reset Input (/MR)
Input Low Voltage (VIL)
Input High Voltage (VIH)
/MR Pulse Width
0.3 × VCC
V
V
0.7 × VCC
1.0
µs
/MR Noise Immunity (pulse
width with no reset)
100
ns
/MR to RESET Delay
/MR Internal Pull-Up Resistor
Notes:
500
52
ns
35
75
kΩ
2. Exceeding the absolute maximum ratings may damage the device.
3. The device is not guaranteed to function outside its operating ratings.
4. Devices are ESD sensitive. Handling precautions are recommended. Human body model, 1.5kΩ in series with 100pF.
5. Specification for packaged product only.
6. Overtemperature limits are guaranteed by design and not product tested.
7. The /RESET short-circuit current is the maximum pull-up current when /RESET is driven low by µP bidirectional reset pin.
8. The WDI input is designed to drive a three-state output device with a 10µA maximum leakage current and a maximum capacitance of 200pF.
Revision 1.0
January 14, 2014
7
Micrel, Inc.
MAX823/4/5
Typical Characteristics
Supply Current
vs. Input Voltage
Supply Current
vs. Temperature
RESET Timeout Period
vs. Temperature
6
7
6
5
4
3
2
1
0
250
200
150
100
50
5
MAX824L, VCC = 5.5V
MAX823W
4
MAX823W, VCC = 2V
MAX824L
3
2
1
0
MAX825S, VCC = 3.25V
MAX825S
/MR = OPEN
WDI = OPEN
/MR = Open
WDI = Open
/MR = OPEN
WDI = OPEN
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
-40
-20
0
20
40
60
80
100 120
-40 -20
0
20
40
60
80 100 120
INPUT VOLTAGE (V)
TEMPERATURE (ꢀC)
TEMPERATURE (°C)
Normalized Reset Threshold
vs. Temperature
/MR to RESET Delay
vs. Temperature
Watchdog Timeout Period vs.
Temperature
800
700
600
500
400
300
200
100
0
2
1.06
1.8
1.6
1.4
1.2
1
1.04
1.02
1
0.98
0.96
0.94
0.92
0.8
0.6
0.4
0.2
0
-40 -20
0
20 40 60 80 100 120 140
-40 -20
0
20
40
60
80 100 120
-40 -20
0
20
40
60
80 100 120
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
Revision 1.0
January 14, 2014
8
Micrel, Inc.
MAX823/4/5
Functional Diagram
Timing Diagram
Revision 1.0
January 14, 2014
9
Micrel, Inc.
MAX823/4/5
Functional Description
Design and Product Advantages
The MAX823/4/5 is series of a voltage supervisor reset
IC with a manual reset input, watchdog input, and dual
reset outputs. The MAX823/4/5 asserts and holds a reset
when the supply voltage falls below the factory-
programmed threshold voltage, when /MR is at low logic
level, or when watchdog input times out. Reset is
asserted for a fixed reset timeout period after the supply
voltage increases above the rising threshold voltage or
when the manual reset input is asserted high.
The MAX823/4/5 features an active-low, push-pull reset
output (/RESET) and an active-high, push-pull reset
output (RESET). It also contains 52kΩ pull-up resistors
on the /MR input to make it easy to connect to
pushbutton inputs. The MAX823/4 also features a
watchdog input (WDI).
Figure 1. Manual Reset Function
When Functioning as a Voltage Supervisor
The /RESET pin is asserted whenever VCC falls below the
reset threshold voltage, VRST (VCC < VRST). The VCC pin
circuitry includes hysteresis to prevent /RESET or
RESET pin chattering due to noise. The /RESET pin
remains asserted for the duration of the reset timeout
delay (tRP) after VCC has risen above the reset threshold
voltage plus the hysteresis. The reset function ensures
that a microprocessor is properly reset and powers up in
a known condition after a power failure. The /RESET
remains valid with VCC as low as 1V. The RESET output
is a complement of the /RESET output.
Manual Reset Input (/MR)
The /MR input pin has integrated pull-up resistors to keep
the current consumption low when the pushbutton switch
is pressed.
Reset Outputs (/RESET and RESET)
There are two reset outputs: /RESET and RESET. Both
outputs are push-pull, which eliminates the need for pull-
up resistors. The RESET output is the inverse of the
/RESET output.
Asserting /RESET and RESET Outputs
When Functioning as a Manual Reset
The reset outputs /RESET and RESET are asserted
while the /MR pin is driven low. Both reset outputs remain
asserted for a factory-programmed reset timeout delay
time, tRP. The typical value of a reset timeout period is
200ms. The /RESET pin is driven low while the RESET
pin is driven high whenever /MR is pulled low.
Figure 2. Voltage Supervisor Function
Revision 1.0
January 14, 2014
10
Micrel, Inc.
MAX823/4/5
VCC Transient
Watchdog Input
The MAX823/4/5 is relatively immune to small negative-
going VCC glitches below the reset threshold. As shown in
Figure 4, the overdrive voltage is the difference between
the threshold voltage and the minimum point of the VCC
glitch. Typically, an overdrive of 100mV with duration of
2μs or less will not cause a reset.
The MAX823/4 has an on-chip watchdog timer that can
reset the microprocessor if it fails to strobe the WDI input
within a preset timeout period (tWD). If the WDI pin is left
unconnected, this function is disabled. The watchdog
timeout period starts when the reset outputs are
deasserted or either
a
high-to-low or low-to-high
transition occurs before the watchdog timeout period
(tWD). If the watchdog timer times out, then the reset
outputs will assert and stay asserted for a reset timeout
period (tRP). The watchdog timer is also cleared whenever
the reset outputs are asserted by /MR, or if VCC falls
below VRST. The watchdog timer starts again whenever
the reset outputs are de-asserted.
Figure 4. VCC Transient
Reset Valid up to VCC = 1V
The MAX823/4/5 is a supervisory circuit that monitors the
power supply voltage level. If the power supply voltage
level falls below the factory-programmed threshold level,
then the reset signals are asserted. The MAX823/4/5
maintains the reset states with VCC as low as 1V.
Supply Bypass Capacitor
An optional 0.1µF input bypass capacitor can be placed
from VCC (Pin 6) to GND (Pin 2) to increase glitch
rejection and provides additional transient immunity.
Figure 3. Watchdog Input
Watchdog Input Current
The WDI input current is the current sourced or sinked by
the WDI pin when the WDI input is driven low or high,
respectively. The WDI input is designed to drive a tri-
state output device with a 10µA maximum leakage
current and a maximum capacitance of 200pF.
Revision 1.0
January 14, 2014
11
Micrel, Inc.
MAX823/4/5
Typical Applications
Figure 5. MAX825 for Precision Power Good Function
Figure 6. MAX823 Used for Load Switch
Figure 7. MAX824 Used for Microcontroller Reset with Watchdog Input
Revision 1.0
January 14, 2014
12
Micrel, Inc.
MAX823/4/5
Package Information(9)
5-Pin SOT23 (EUK)
Revision 1.0
January 14, 2014
13
Micrel, Inc.
MAX823/4/5
Package Information (Continued)(9)
5-Pin SC70 (EXK)
Note:
9. Package information is correct as of the publication date. For updates and the most current information, go to www.micrel.com.
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com
Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This
information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry,
specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual
property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability
whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties
relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product
can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical
implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A
Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully
indemnify Micrel for any damages resulting from such use or sale.
© 2014 Micrel, Incorporated.
Revision 1.0
January 14, 2014
14
相关型号:
MAX825SEUK+T
Power Supply Support Circuit, Fixed, 1 Channel, +2.93VV, BICMOS, PDSO5, ROHS COMPLIANT, MO-178AA, SOT-23, 5 PIN
MAXIM
MAX825SEXK+
Power Supply Support Circuit, Fixed, 1 Channel, BICMOS, PDSO5, LEAD FREE, SC-70, 5 PIN
MAXIM
MAX825SEXK+T
Power Supply Management Circuit, Fixed, 1 Channel, +2.93VV, BICMOS, PDSO5, ROHS COMPLIANT, SC-70, 5 PIN
MAXIM
©2020 ICPDF网 联系我们和版权申明