27C16A-25P [MICROCHIP]
16K (2K x 8) CMOS EEPROM; 16K ( 2K ×8 )的CMOS EEPROM型号: | 27C16A-25P |
厂家: | MICROCHIP |
描述: | 16K (2K x 8) CMOS EEPROM |
文件: | 总8页 (文件大小:68K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
28C16A
16K (2K x 8) CMOS EEPROM
FEATURES
PACKAGE TYPES
A7
A6
• 1
2
24 Vcc
23 A8
• Fast Read Access Time—150 ns
• CMOS Technology for Low Power Dissipation
- 30 mA Active
A6
A5
A4
A3
A2
A1 10
A0 11
NC 12
I/O0 13
5
6
7
8
9
29 A8
28 A9
A5
3
22 A9
A4
4
21 WE
20 OE
19 A10
18 CE
17 I/O7
16 I/O6
15 I/O5
14 I/O4
13 I/O3
27 NC
26 NC
25 OE
24 A10
23 CE
22 I/O7
21 I/O6
A3
5
- 100 µA Standby
A2
6
• Fast Byte Write Time—200 µs or 1 ms
• Data Retention >200 years
A1
7
A0
8
4
I/O0
I/O1
I/O2
9
• High Endurance - Minimum 10 Erase/Write Cycles
10
11
• Automatic Write Operation
- Internal Control Timer
VSS 12
- Auto-Clear Before Write Operation
- On-Chip Address and Data Latches
• Data polling
• Chip Clear Operation
• Enhanced Data Protection
- VCC Detector
• Pin 1 indicator on PLCC on top of package
OE
NC
A9
1
2
3
4
5
6
7
28 A10
27
CE
26 I/07
25 I/06
24 I/05
23 I/04
22 I/03
A8
NC
WE
Vcc
- Pulse Filter
- Write Inhibit
NC
NC
8
9
21 Vss
20 I/02
19 I/01
18 I/00
17 A0
16 A1
15 A2
A7 10
A6 11
A5 12
A4 13
A3 14
• Electronic Signature for Device Identification
• 5-Volt-Only Operation
• Organized 2Kx8 JEDEC Standard Pinout
• 24-pin Dual-In-Line Package
• 32-pin PLCC Package
• 28-pin Thin Small Outline Package (TSOP)
8x20mm
• 28-pin Very Small Outline Package (VSOP)
8x13.4mm
OE
NC
A9
A8
NC
WE
22
23
24
25
26
27
A10
CE
21
20
19
18
17
16
15
14
13
12
11
10
9
I/O7
I/O6
I/O5
I/O4
I/O3
VSS
I/O2
I/O1
I/O0
A0
28
1
VCC
NC
2
3
4
5
6
7
NC
A7
A6
A5
A4
A3
• Available for Extended Temperature Ranges:
- Commercial: 0˚C to +70˚C
- Industrial: -40˚C to +85˚C
A1
A2
8
BLOCK DIAGRAM
DESCRIPTION
I/O0
I/O7
The Microchip Technology Inc. 28C16A is a CMOS 16K
non-volatile electrically Erasable PROM. The 28C16A
is accessed like a static RAM for the read or write
cycles without the need of external components. Dur-
ing a “byte write”, the address and data are latched
internally, freeing the microprocessor address and data
bus for other operations. Following the initiation of
write cycle, the device will go to a busy state and auto-
matically clear and write the latched data using an
internal control timer. To determine when a write cycle
is complete, the 28C16A uses Data polling. Data poll-
ing allows the user to read the location last written to
when the write operation is complete. CMOS design
and processing enables this part to be used in systems
where reduced power consumption and reliability are
required. A complete family of packages is offered to
provide the utmost flexibility in applications.
VSS
Data Protection
VCC
Circuitry
Chip Enable/
Output Enable
Control Logic
CE
OE
Input/Output
Buffers
WE
Auto Erase/Write
Timing
Data
Poll
Program Voltage
Generation
A0
Y
Y Gating
Decoder
L
a
t
c
h
e
s
16K bit
X
Decoder
Cell Matrix
A10
1996 Microchip Technology Inc.
DS11125G-page 1
28C16A
TABLE 1-1:
Name
PIN FUNCTION TABLE
Function
1.0
ELECTRICAL CHARACTERISTICS
1.1
MAXIMUM RATINGS*
VCC and input voltages w.r.t. VSS.......-0.6V to + 6.25V
Voltage on OE w.r.t. VSS .....................-0.6V to +13.5V
Voltage on A9 w.r.t. VSS ......................-0.6V to +13.5V
Output Voltage w.r.t. VSS................ -0.6V to VCC+0.6V
Storage temperature .......................... -65˚C to +125˚C
Ambient temp. with power applied ....... -50˚C to +95˚C
A0 - A10
CE
Address Inputs
Chip Enable
OE
Output Enable
Write Enable
WE
I/O0 - I/O7 Data Inputs/Outputs
VCC
VSS
NC
+5V Power Supply
*Notice: Stresses above those listed under “Maximum Ratings”
may cause permanent damage to the device. This is a stress rat-
ing only and functional operation of the device at those or any
other conditions above those indicated in the operation listings of
this specification is not implied. Exposure to maximum rating con-
ditions for extended periods may affect device reliability.
Ground
No Connect; No Internal Connection
NU
Not Used; No External Connection is
Allowed
TABLE 1-2:
READ/WRITE OPERATION DC CHARACTERISTICS
VCC = +5V ±10%
Commercial (C): Tamb = 0˚C
to +70˚C
Industrial
(I): Tamb = -40˚C to +85˚C
Parameter
Status
Symbol
Min
Max
Units
Conditions
Input Voltages
Logic ‘1’
Logic ‘0;
VIH
VIL
2.0
-0.1
VCC+1
0.8
V
V
Input Leakage
—
—
ILI
-10
—
10
10
µA
VIN = -0.1V to VCC+1
Input Capacitance
CIN
pF
VIN = 0V; Tamb = 25˚C;
f = 1 MHz
Output Voltages
Logic ‘1’
Logic ‘0’
VOH
VOL
2.4
V
V
IOH = -400µA
IOL = 2.1 mA
0.45
10
Output Leakage
—
—
ILO
-10
—
µA
VOUT = -0.1V to VCC+0.1V
Output Capacitance
COUT
12
pF
VIN = 0V; Tamb = 25˚C;
f = 1 MHz
Power Supply Current,
Active
TTL input
ICC
—
—
30
mA
f = 5 MHz (Note 1)
VCC = 5.5V;
Power Supply Current,
Standby
TTL input
TTL input
CMOS input ICC(S)CMOS
ICC(S)TTL
ICC(S)TTL
2
3
100
mA
mA
µA
CE = VIH (0˚C to +70˚C)
CE = VIH (-40˚C to +85˚C)
CE = VCC-0.3 to VCC+1
Note 1: AC power supply current above 5 MHz; 1 mA/MHz.
DS11125G-page 2
1996 Microchip Technology Inc.
28C16A
TABLE 1-3:
READ OPERATION AC CHARACTERISTICS
AC Testing Waveform:
Output Load:
VIH = 2.4V; VIL = 0.45V; VOH = 2.0V; Vol = 0.8V
1 TTL Load + 100pF
Input Rise and Fall Times: 20 ns
Ambient Temperature:
Commercial (C): Tamb = 0˚C to +70˚0˚C
Industrial (I):
Tamb = -40˚C to +85˚C
28C16A-15
Sym
28C16A-20
28C16A-25
Parameter
Units
Conditions
Min
Max
Min
Max
Min
Max
Address to Output Delay
CE to Output Delay
tACC
tCE
—
—
—
0
150
150
70
—
—
—
0
200
200
80
—
—
—
0
250
250
100
70
ns
ns
ns
ns
ns
OE = CE = VIL
OE = VIL
OE to Output Delay
tOE
CE = VIL
CE or OE High to Output Float
tOFF
tOH
50
55
Output Hold from CE or OE,
whichever occurs first
0
—
0
—
0
—
Endurance
—
1M
—
1M
—
1M
—
cycles 25°C, Vcc =
5.0V, Block
Mode (Note)
Note: This parameter is not tested but guaranteed by characterization. For endurance estimates in a specific appli-
cation, please consult the Total Endurance Model which can be obtained on our BBS or website.
FIGURE 1-1: READ WAVEFORMS
VIH
Address
CE
Address Valid
VIL
VIH
VIL
tCE(2)
VIH
VIL
OE
tOFF(1,3)
tOH
tOE(2)
VOH
High Z
High Z
Data
WE
Valid Output
VOL
VIH
VIL
tACC
Notes: (1) tOFF is specified for OE or CE, whichever occurs first
(2) OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE
(3) This parameter is sampled and is not 100% tested
1996 Microchip Technology Inc.
DS11125G-page 3
28C16A
TABLE 1-4:
BYTE WRITE AC CHARACTERISTICS
AC Testing Waveform:
Output Load:
Input Rise/Fall Times:
Ambient Temperature:
VIH = 2.4V and VIL = 0.45V; VOH = 2.0V; VOL = 0.8V
1 TTL Load + 100 pF
20 ns
Commercial (C):
Industrial (I):
Tamb
Tamb
=
=
0˚C to +70˚C
-40˚C to +85˚C
Parameter
Symbol
Min
Max
Units
Remarks
Address Set-Up Time
Address Hold Time
Data Set-Up Time
Data Hold Time
tAS
tAH
10
50
50
10
100
50
10
10
—
—
—
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
µs
tDS
—
tDH
—
Write Pulse Width
Write Pulse High Time
OE Hold Time
tWPL
tWPH
tOEH
tOES
tDV
—
Note 1
—
—
OE Set-Up Time
—
Data Valid Time
1000
1
Note 2
tWC
tWC
—
0.5 ms typical
100 µs typical
Write Cycle Time (28C16A)
Write Cycle Time (28C16AF)
—
200
Note 1: A write cycle can be initiated be CE or WE going low, whichever occurs last. The data is latched on the pos-
itive edge of CE or WE, whichever occurs first.
2: Data must be valid within 1000ns max. after a write cycle is initiated and must be stable at least until tDH
after the positive edge of WE or CE, whichever occurs first.
FIGURE 1-2: PROGRAMMING WAVEFORMS
VIH
Address
VIL
tAS
tAH
VIH
VIL
tWPL
tDS
CE, WE
Data In
tDH
tDV
VIH
VIL
tOES
VIH
VIL
OE
tOEH
DS11125G-page 4
1996 Microchip Technology Inc.
28C16A
FIGURE 1-3: DATA POLLING WAVEFORMS
VIH
Last Written
Address Valid
Address Valid
Address
CE
VIL
t ACC
VIH
VIL
tCE
t WPH
VIH
VIL
tWPL
WE
tOE
VIH
VIL
OE
tDV
VIH
VIL
Data In
Valid
True Data Out
Data
I/O7 Out
tWC
FIGURE 1-4: CHIP CLEAR WAVEFORMS
VIH
CE
VIL
VH
OE
VIH
tS
tH
tW
VIH
WE
tW
= 10ms
VIL
tS = = 1µs
tH
= 12.0V ±0.5V
VH
TABLE 1-5:
SUPPLEMENTARY CONTROL
Mode
CE
OE
WE
A9
VCC
I/OI
Chip Clear
VIL
VIL
*
VH
VIL
VIH
VIL
VIH
*
X
VCC
Extra Row Read
Extra Row Write
Note 1: VH = 12.0V±0.5V
A9 = VH
A9 = VH
VCC
VCC
Data Out
Data In
* Pulsed per programming waveforms.
1996 Microchip Technology Inc.
DS11125G-page 5
28C16A
2.4
Write Mode
2.0
DEVICE OPERATION
The Microchip Technology Inc. 28C16A has four basic
modes of operation—read, standby, write inhibit, and
byte write—as outlined in the following table.
The 28C16A has a write cycle similar to that of a Static
RAM. The write cycle is completely self-timed and ini-
tiated by a low going pulse on the WE pin. On the fall-
ing edge of WE, the address information is latched. On
rising edge, the data and the control pins (CE and OE)
are latched.
Operation
CE
OE
WE
I/O
Mode
Read
L
H
H
X
X
L
L
X
X
L
H
X
X
X
H
L
DOUT
High Z
High Z
High Z
High Z
DIN
2.5
Data Polling
Standby
The 28C16A features Data polling to signal the com-
pletion of a byte write cycle. During a write cycle, an
attempted read of the last byte written results in the
data complement of I/O7 (I/O0 to I/O6 are indetermin-
able). After completion of the write cycle, true data is
available. Data polling allows a simple read/compare
operation to determine the status of the chip eliminat-
ing the need for external hardware.
Write Inhibit
Write Inhibit
Write Inhibit
Byte Write
X
H
Byte Clear
Automatic Before Each “Write”
X = Any TTL level.
2.6
Electronic Signature for Device
Identification
2.1
Read Mode
An extra row of 32 bytes of EEPROM memory is avail-
able to the user for device identification. By raising A9
to 12V ±0.5V and using address locations 7EO to 7FF,
the additional bytes can be written to or read from in the
same manner as the regular memory array.
The 28C16A has two control functions, both of which
must be logically satisfied in order to obtain data at the
outputs. Chip enable (CE) is the power control and
should be used for device selection. Output Enable
(OE) is the output control and is used to gate data to
the output pins independent of device selection.
Assuming that addresses are stable, address access
time (tACC) is equal to the delay from CE to output (tCE).
Data is available at the output tOE after the falling edge
of OE, assuming that CE has been low and addresses
have been stable for at least tACC-tOE.
2.7
Chip Clear
All data may be cleared to 1's in a chip clear cycle by
raising OE to 12 volts and bringing the WE and CE
low. This procedure clears all data, except for the extra
row.
2.2
Standby Mode
The 28C16A is placed in the standby mode by applying
a high signal to the CE input. When in the standby
mode, the outputs are in a high impedance state, inde-
pendent of the OE input.
2.3
Data Protection
In order to ensure data integrity, especially during criti-
cal power-up and power-down transitions, the following
enhanced data protection circuits are incorporated:
First, an internal VCC detect (3.3 volts typical) will inhibit
the initiation of non-volatile programming operation
when VCC is less than the VCC detect circuit trip.
Second, there is a WE filtering circuit that prevents WE
pulses of less than 10 ns duration from initiating a write
cycle.
Third, holding WE or CE high or OE low, inhibits a write
cycle during power-on and power-off (VCC).
DS11125G-page 6
1996 Microchip Technology Inc.
28C16A
28C16A Product Identification System
To order or to obtain information, e.g., on pricing or delivery, please use the listed part numbers, and refer to the factory or the listed
sales offices.
28C16A
F
T
–
15
I
/P
Package:
L = Plastic Leaded Chip Carrier (PLCC)
P = Plastic DIP (600 mil)
TS = Thin Small Outline Package (TSOP) 8x20mm
VS = Very Small Outline Package (VSOP) 8x13.4mm
Temperature
Range:
Blank = 0°C to +70°C
I = -40°C to +85°C
Access Time:
15 150 ns
20 200 ns
25 250 ns
Shipping:
Option:
Device:
Blank Tube
T
Tape and Reel “L” only
Blank = twc = 1ms
F = twc = 200 µs
28C16A 2K x 8 CMOS EEPROM
1996 Microchip Technology Inc.
DS11125G-page 7
WORLDWIDE SALES & SERVICE
AMERICAS
Corporate Office
ASIA/PACIFIC
China
EUROPE
United Kingdom
Microchip Technology Inc.
Microchip Technology
Arizona Microchip Technology Ltd.
Unit 6, The Courtyard
Meadow Bank, Furlong Road
Bourne End, Buckinghamshire SL8 5AJ
Tel: 44 1628 850303 Fax: 44 1628 850178
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 602 786-7200 Fax: 602 786-7277
Technical Support: 602 786-7627
Web: http://www.microchip.com
Unit 406 of Shanghai Golden Bridge Bldg.
2077 Yan’an Road West, Hongiao District
Shanghai, Peoples Republic of China
Tel: 86 21 6275 5700
Fax: 011 86 21 6275 5060
Hong Kong
Microchip Technology
RM 3801B, Tower Two
Metroplaza
223 Hing Fong Road
Kwai Fong, N.T. Hong Kong
Tel: 852 2 401 1200 Fax: 852 2 401 3431
India
Microchip Technology
No. 6, Legacy, Convent Road
Bangalore 560 025 India
Tel: 91 80 526 3148 Fax: 91 80 559 9840
France
Atlanta
Arizona Microchip Technology SARL
Zone Industrielle de la Bonde
2 Rue du Buisson aux Fraises
91300 Massy - France
Tel: 33 1 69 53 63 20 Fax: 33 1 69 30 90 79
Germany
Arizona Microchip Technology GmbH
Gustav-Heinemann-Ring 125
D-81739 Muenchen, Germany
Tel: 49 89 627 144 0 Fax: 49 89 627 144 44
Microchip Technology Inc.
500 Sugar Mill Road, Suite 200B
Atlanta, GA 30350
Tel: 770 640-0034 Fax: 770 640-0307
Boston
Microchip Technology Inc.
5 Mount Royal Avenue
Marlborough, MA 01752
Tel: 508 480-9990 Fax: 508 480-8575
Chicago
Italy
Microchip Technology Inc.
333 Pierce Road, Suite 180
Itasca, IL 60143
Tel: 708 285-0071 Fax: 708 285-0075
Dallas
Microchip Technology Inc.
14651 Dallas Parkway, Suite 816
Dallas, TX 75240-8809
Tel: 972 991-7177 Fax: 972 991-8588
Dayton
Microchip Technology Inc.
Suite 150
Arizona Microchip Technology SRL
Centro Direzionale Colleone Pas Taurus 1
Viale Colleoni 1
20041 Agrate Brianza
Milan Italy
Korea
Microchip Technology
168-1, Youngbo Bldg. 3 Floor
Samsung-Dong, Kangnam-Ku,
Seoul, Korea
Tel: 82 2 554 7200 Fax: 82 2 558 5934
Singapore
Microchip Technology
200 Middle Road
#10-03 Prime Centre
Singapore 188980
Tel: 65 334 8870 Fax: 65 334 8850
Taiwan, R.O.C
Microchip Technology
10F-1C 207
Tung Hua North Road
Taipei, Taiwan, ROC
Tel: 886 2 717 7175 Fax: 886 2 545 0139
Tel: 39 39 6899939 Fax: 39 39 689 9883
JAPAN
Microchip Technology Intl. Inc.
Benex S-1 6F
3-18-20, Shin Yokohama
Kohoku-Ku, Yokohama
Kanagawa 222 Japan
Two Prestige Place
Miamisburg, OH 45342
Tel: 513 291-1654 Fax: 513 291-9175
Tel: 81 45 471 6166 Fax: 81 45 471 6122
9/3/96
Los Angeles
Microchip Technology Inc.
18201 Von Karman, Suite 1090
Irvine, CA 92612
Tel: 714 263-1888 Fax: 714 263-1338
NewYork
Microchip Technmgy Inc.
150 Motor Parkway, Suite 416
Hauppauge, NY 11788
Tel: 516 273-5305 Fax: 516 273-5335
San Jose
Microchip Technology Inc.
2107 North First Street, Suite 590
San Jose, CA 95131
Tel: 408 436-7950 Fax: 408 436-7955
Toronto
Microchip Technology Inc.
5925 Airport Road, Suite 200
Mississauga, Ontario L4V 1W1, Canada
Tel: 905 405-6279 Fax: 905 405-6253
All rights reserved. 1996, Microchip Technology Incorporated, USA. 9/96
Printed on recycled paper.
Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. No repre-
sentation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement
of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not autho-
rized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip logo and
name are registered trademarks of Microchip Technology Inc. All rights reserved. All other trademarks mentioned herein are the property of their respective companies.
DS11125G-page 8
1996 Microchip Technology Inc.
相关型号:
©2020 ICPDF网 联系我们和版权申明