AT24C02C-SSHM-T-989 [MICROCHIP]
EEPROM, 256X8, Serial, CMOS, PDSO8;
| 型号： | AT24C02C-SSHM-T-989 |
| 厂家： | 
MICROCHIP |
| 描述： | EEPROM, 256X8, Serial, CMOS, PDSO8 可编程只读存储器 电动程控只读存储器 电可擦编程只读存储器 时钟 光电二极管 内存集成电路 |
| 文件： | 总22页 (文件大小：1002K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
AT24C01C and AT24C02C
I2C-Compatible (2-wire) Serial EEPROM
1-Kbit (128 x 8), 2-Kbit (256 x 8)
DATASHEET
Features
Low-voltage Operation
VCC = 1.7V to 5.5V
̶
Internally Organized as 128 x 8 (1K) or 256 x 8 (2K)
I2C Compatible (2-wire) Serial Interface
Schmitt Trigger, Filtered Inputs for Noise Suppression
Bidirectional Data Transfer Protocol
400kHz (1.7V) and 1MHz (2.5V, 2.7V, 5.0V) Compatibility
Write Protect Pin for Hardware Data Protection
8-byte Page Write Mode
̶
Partial Page Writes Allowed
Self-timed Write Cycle (5ms max)
High-reliability
̶
̶
Endurance: 1,000,000 Write Cycles
Data Retention: 100 Years
Green Package Options (Pb/Halide-free/RoHS-compliant)
̶
8-lead PDIP, 8-lead JEDEC SOIC, 8-lead TSSOP, 8-pad UDFN, 5-lead
SOT23, and 8-ball VFBGA
Die Sale Options: Wafer Form and Tape and Reel Available
Description
The Atmel® AT24C01C/02C provides 1024/2048-bits of Serial Electrically
Erasable and Programmable Read-Only Memory (EEPROM) organized as
128/256 words of eight bits each. Both devices include a cascading feature that
allows up to eight devices to share a common 2-wire bus. These devices are
optimized for use in many industrial and commercial applications where low
power and low voltage operation are essential. The AT24C01C/02C are available
in space saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead TSSOP, 8-lead UDFN,
5-lead SOT23, and 8-ball VFBGA packages. In addition, the entire family
operates from 1.7V to 5.5V VCC
.
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
1.
Pin Configurations and Pinouts
Table 1-1.
Pin Descriptions
Pin
Number
Pin
Symbol
Asserted
State
Pin
Type
Pin Name and Functional Description
Address Inputs: The A2, A1, and A0 pins are device address inputs that
are hard wired. As many as eight 1-Kbit or 2-Kbit devices may be
addressed on a single bus system.
1, 2, 3
A0 – A2
—
—
—
Input
Ground: The ground reference for the power supply. GND should be
connected to the system ground.
4
5
GND
SDA
Power
Serial Data: The SDA pin is bidirectional for serial data transfer. This pin
is open drain driven and may be wire-ORed with any number of other
open drain or open collector devices.
Input/
Output
Serial Clock Input: The SCL input is used to positive edge clock data
into each EEPROM device and negative edge clock data out of each
device.
6
7
8
SCL
WP
VCC
—
Input
Input
Write Protect: Provides hardware data protection. The Write Protect pin
allows normal read/write operations when connected to Ground (GND).
When the Write Protect pin is connected to VCC, the write protection
feature is enabled and operates as shown in Table 5-1.
Device Power Supply: The VCC pin is used to supply the source voltage
to the device. Operations at invalid VCC voltages may produce spurious
results and should not be attempted.
—
Power
Note:
1. For use of 5-lead SOT23, the software A2, A1, and A0 bits in the device address word must be set to zero to
properly communicate.
8-pad UDFN
8-lead SOIC
8-lead TSSOP
1
2
3
4
8
7
6
5
A0
A1
VCC
WP
A0
A1
A2
1
2
3
4
8
7
6
5
VCC
WP
SCL
SDA
A0
A1
VCC
WP
SCL
SDA
1
2
3
4
8
7
6
5
A2
SCL
SDA
A2
GND
GND
GND
Top View
Top View
5-lead SOT23
Top View
8-ball VFBGA
8-lead PDIP
1
2
3
4
8
7
6
5
1
2
3
4
A0
8
7
6
5
VCC
A0
A1
A2
VCC
SCL
GND
SDA
1
2
3
5
WP
VCC
WP
A1
A2
WP
SCL
SDA
SCL
SDA
4
GND
GND
Top View
Top View
Top View
Note: Package drawings are not to scale.
2
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
2.
Block Diagram
Figure 2-1.
Block Diagram
VCC
GND
WP
Start
Stop
Logic
SCL
SDA
Serial
Control
Logic
EN
H.V. Pump/Timing
Data Recovery
LOAD
COMP
Device
Address
Comparator
LOAD
INC
A2
A1
A0
R/W
Data Word
Addr/counter
EEPROM
Serial MUX
Y DEC
DOUT/ACK
Logic
DIN
DOUT
3.
Absolute Maximum Ratings
*Notice: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent
damage to the device. This is a stress rating
only and functional operation of the device at
these or any other conditions beyond those
indicated in the operational sections of this
specification is not implied. Exposure to
Operating Temperature . . . . . . . . . . .-55C to +125C
Storage Temperature . . . . . . . . . . . . .-65C to +150C
Voltage on any pin
with respect to ground . . . . . . . . . . . . . -1.0V to +7.0V
Maximum Operating Voltage . . . . . . . . . . . . . . . 6.25V
DC Output Current . . . . . . . . . . . . . . . . . . . . . . .5.0mA
absolute maximum rating conditions for
extended periods may affect device reliability.
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
3
4.
Memory Organization
AT24C01C, 1K Serial EEPROM: Internally organized with 16 pages of eight bytes each, the 1K requires a 7-bit
data word address for random word addressing.
AT24C02C, 2K Serial EEPROM: Internally organized with 32 pages of eight bytes each, the 2K requires an
8-bit data word address for random word addressing.
4.1
Pin Capacitance
Table 4-1.
Applicable over recommended operating range from TA = 25C, f = 1.0MHz, VCC = 1.7V to 5.5V.
Pin Capacitance(1)
Symbol
CI/O
Test Condition
Max
8
Units
pF
Conditions
VI/O = 0V
VIN = 0V
Input/Output Capacitance (SDA)
Input Capacitance (A0, A1, A2, SCL)
CIN
6
pF
Note:
1. This parameter is characterized and is not 100% tested.
4.2
DC Characteristics
Table 4-2.
DC Characteristics
Applicable over recommended operating range from: TAI = -40°C to +85°C, VCC = 1.7V to 5.5V (unless otherwise noted).
Symbol
VCC1
VCC2
VCC3
ICC1
ICC2
ISB1
Parameter
Test Condition
Min
1.7
2.5
4.5
Typ
Max
5.5
Units
V
Supply Voltage
Supply Voltage
5.5
V
Supply Voltage
5.5
V
Supply Current VCC = 5.0V
Supply Current VCC = 5.0V
Standby Current VCC = 1.7V
Standby Current VCC = 2.5V
Standby Current VCC = 5.5V
Input Leakage Current
Output Leakage Current
Input Low Level(1)
Read at 400kHz
Write at 400kHz
VIN = VCC or VSS
VIN = VCC or VSS
VIN = VCC or VSS
VIN = VCC or VSS
VOUT = VCC or VSS
0.4
2.0
1.0
mA
mA
μA
μA
μA
μA
μA
V
3.0
1.0
ISB2
2.0
ISB3
6.0
ILI
0.10
0.05
3.0
ILO
3.0
VIL
-0.6
VCC x 0.3
VCC + 0.5
0.2
VIH
Input High Level(1)
VCC x 0.7
V
VOL1
VOL2
Output Low Level VCC = 1.7V
Output Low Level VCC = 3.0V
IOL = 0.15mA
IOL = 2.1mA
V
0.4
V
Note:
1. VIL min and VIH max are reference only and are not tested.
4
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
4.3
AC Characteristics
Table 4-3.
AC Characteristics
Applicable over recommended operating range from TAI = -40C to +85C, VCC = 1.7V to 5.5V, CL = 1TTL Gate and 100pF
(unless otherwise noted). Test conditions are listed in Note 2.
1.7V
2.5V, 5.0V
Symbol
fSCL
Parameter
Min
Max
Min
Max
Units
kHz
μs
Clock Frequency, SCL
Clock Pulse Width Low
Clock Pulse Width High
Noise Suppression Time
Clock Low to Data Out Valid
400
1000
tLOW
tHIGH
tI
1.2
0.6
0.4
0.4
μs
100
0.9
50
ns
tAA
0.1
1.2
0.05
0.5
0.55
μs
Time the bus must be free before a
new transmission can start.
tBUF
μs
tHD.STA
tSU.STA
tHD.DAT
tSU.DAT
tR
Start Hold Time
0.6
0.6
0
0.25
0.25
0
μs
Start Setup Time
Data In Hold Time
Data In Setup Time
Inputs Rise Time(1)
Inputs Fall Time(1)
Stop Setup Time
μs
μs
100
100
ns
0.3
0.3
μs
tF
300
100
ns
tSU.STO
tDH
0.6
50
.25
50
μs
ns
Data Out Hold Time
Write Cycle Time
3.3V, +25C, Page Mode
tWR
5
5
ms
Endurance(1)
1,000,000
Write Cycles
Note:
1. This parameter is ensured by characterization only.
2. AC measurement conditions:
RL (connects to VCC): 1.3 k (2.5V, 5V), 10 k (1.7V)
Input pulse voltages: 0.3 VCC to 0.7 VCC
Input rise and fall times: 50ns
Input and output timing reference voltages: 0.5 VCC
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
5
5.
Write Protection
The AT24C01C/02C utilizes a hardware data protection scheme that allows the user to write protect the entire
memory contents when the WP pin is at VCC (or a valid VIH). No write protection will be set if the WP pin is at
GND or left floating.
Table 5-1.
Write Protect
WP Pin Status
At VCC
Part of the Array Protected
Full (2K) Array
At GND
Normal Read/Write Operations
6.
Device Operation
Clock and Data Transitions: The SDA pin is normally pulled high with an external device. Data on the SDA pin
may change only during SCL low time periods. Data changes during SCL high periods will indicate a Start or
Stop condition as defined below.
Figure 6-1.
Data Validity
SDA
SCL
Data Stable
Data Stable
Data
Change
Start Condition: A high-to-low transition of SDA with SCL high is a Start condition which must precede any
other command.
Stop Condition: A low-to-high transition of SDA with SCL high is a Stop condition. After a read sequence, the
Stop condition will place the EEPROM in a standby power mode.
Figure 6-2.
Start and Stop Definition
SDA
SCL
Start
Stop
6
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
Acknowledge: All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words.
The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock
cycle.
Figure 6-3.
Output Acknowledge
1
8
9
SCL
Data In
Data Out
Start
Acknowledge
Standby Mode: The AT24C01C/02C features a low-power standby mode which is enabled:
Upon power-up.
After the receipt of the Stop condition and the completion of any internal operations.
2-wire Software Reset: After an interruption in protocol, power-loss, or system reset, any 2-wire part can be
reset by following these steps:
1. Create a Start condition (if possible).
2. Clock nine cycles.
3. Create another Start condition followed by Stop condition as shown in Figure 6-4.
The device will be ready for the next communication after above steps have been completed. The device should
be ready for the next communication after above steps have been completed. In the event that the device is still
non-responsive or remains active on the SDA bus, a power cycle must be used to reset the device.
Figure 6-4.
Software Reset
Dummy Clock Cycles
3
SCL
1
2
8
9
Start
Condition
Stop
Start
Condition
Condition
SDA
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
7
Figure 6-5.
Bus Timing
SCL: Serial Clock, SDA: Serial Data I/O
tHIGH
tF
tR
tLOW
tLOW
SCL
tSU.STA
tHD.STA
tHD.DAT
tSU.DAT
tSU.STO
SDA IN
tAA
tDH
tBUF
SDA OUT
Figure 6-6.
Write Cycle Timing
SCL: Serial Clock, SDA: Serial Data I/O
SCL
8th Bit
ACK
SDA
WORDN
(1)
t
WR
Start
Stop
Condition
Condition
Note:
1. The write cycle time tWR is the time from a valid Stop condition of a write sequence to the end of the internal
clear/write cycle.
8
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
7.
Device Addressing
The 1-Kbit and 2-Kbit EEPROM device requires an 8-bit device address word following a Start condition to
enable the device for a Read or Write operation.
The device address word consists of a mandatory ‘1010’ (0xA) sequence for the first four most significant bits
as shown in Figure 7-1. This is common to all Serial EEPROM devices.
The next three bits are the A2, A1, and A0 device address bits for the 1K and 2K EEPROM. These three bits
must compare to their corresponding hard-wired input pins A2, A1, and A0 in order for the part to acknowledge.
The eighth bit of the device address is the Read/Write operation select bit. A Read operation is initiated if this bit
is high and a Write operation is initiated if this bit is low.
Upon a valid compare of the device address with hard-wired input pins A2, A1, and A0, the EEPROM will output
a zero. If a compare is not successfully made, the chip will return to a standby state.
Figure 7-1.
Device Address
1K or 2K
1
0
1
0
A2
A1
A0 R/W
LSB
MSB
8.
Write Operations
Byte Write: A Byte Write operation requires an 8-bit data word address following the device address word and
acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in
the first 8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a zero and the
addressing device, such as a microcontroller, must terminate the write sequence with a Stop condition. At this
time, the EEPROM enters an internally timed write cycle, tWR, to the nonvolatile memory. All inputs are disabled
during this write cycle and the EEPROM will not respond until the write is complete.
Figure 8-1.
Byte Write
S
T
W
R
I
S
T
A
R
T
Device
Address
T
E
O
P
Word Address
Data
SDA LINE
M
S
B
R A
A
C
K
A
C
K
/
C
W K
Page Write: The 1-Kbit and 2-Kbit EEPROM are capable of an 8-byte Page Write.
A Page Write is initiated the same as a Byte Write, but the microcontroller does not send a Stop condition after
the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the
microcontroller can transmit up to seven data words. The EEPROM will respond with a zero after each data
word received. The microcontroller must terminate the page write sequence with a Stop condition.
The data word address lower three bits are internally incremented following the receipt of each data word. The
higher data word address bits are not incremented, retaining the memory page row location. When the word
address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the
same page. If more than eight data words are transmitted to the EEPROM, the data word address will “roll over”
and previous data will be overwritten.
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
9
Figure 8-2.
Page Write
S
T
A
R
T
W
R
I
S
T
Device
Address
Word
Address (n)
T
E
O
P
Data (n)
Data (n + 1)
Data (n + x)
SDA LINE
M
S
B
R A
A
C
K
A
C
K
A
C
K
A
C
K
/
C
W K
Acknowledge Polling: Once the internally timed write cycle has started and the EEPROM inputs are disabled,
acknowledge polling can be initiated. This involves sending a Start condition followed by the device address
word. The read/write bit is representative of the operation desired. Only if the internal write cycle has completed
will the EEPROM respond with a zero allowing the read or write sequence to continue.
Data Security: The AT24C01C/02C has a hardware data protection scheme that allows the user to write
protect the entire memory when the WP pin is at VCC
.
9.
Read Operations
Read operations are initiated the same way as write operations with the exception that the read/write select bit
in the device address word is set to one. There are three read operations:
Current Address Read
Random Address Read
Sequential Read.
Current Address Read: The internal data word address counter maintains the last address accessed during
the last read or write operation, incremented by one. This address stays valid between operations as long as the
chip power is maintained. The address roll-over during read is from the last byte of the last memory page to the
first byte of the first page. The address roll-over during write is from the last byte of the current page to the first
byte of the same page.
Once the device address with the read/write select bit set to one is clocked in and acknowledged by the
EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an
zero but does generate a following Stop condition
Figure 9-1.
Current Address Read
S
T
R
S
T
A
R
T
E
A
D
Device
Address
O
P
Data
SDA LINE
M
S
B
R A
N
O
/
C
W K
A
C
K
10
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
Random Read: A Random Read requires a dummy byte write sequence to load in the data word address. Once
the device address word and data word address are clocked in and acknowledged by the EEPROM, the
microcontroller must generate another start condition. The microcontroller now initiates a Current Address Read
by sending a device address with the read/write select bit high. The EEPROM acknowledges the device
address and serially clocks out the data word. The microcontroller does not respond with a zero but does
generate a following stop condition.
Figure 9-2.
Random Read
S
T
W
R
I
S
T
A
R
T
R
E
A
D
S
T
A
R
T
Device
Address
Word
Address (n)
Device
Address
T
E
O
P
Data (n)
SDA LINE
M
S
B
R A
A
C
K
A
C
K
N
O
/
C
W K
A
C
K
Dummy Write
Sequential Read: Sequential Reads are initiated by either a Current Address Read or a Random Address
Read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM
receives an acknowledge, it will continue to increment the data word address and serially clock out sequential
data words. When the memory address limit is reached, the data word address will roll-over and the Sequential
Read will continue. The Sequential Read operation is terminated when the microcontroller does not respond
with a zero but does generate a following stop condition.
Figure 9-3.
Sequential Read
R
E
S
T
A
C
K
A
C
K
A
C
K
Device
Address
A
D
O
P
Data (n)
Data (n + 1)
Data (n + 2)
Data (n + x)
SDA LINE
M
S
B
R A
/ C
N
O
W K
A
C
K
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
11
10. Ordering Code Detail
A T 2 4 C 0 1 C - S S H M - B
Atmel Designator
Product Family
Shipping Carrier Option
B or Blank = Bulk (Tubes)
T
E
=
=
Tape and Reel, Standard Quantity Option
Tape and Reel, Expanded Quantity Option
24C = Standard I2C-compatible
Serial EEPROM
Operating Voltage
1.7V to 5.5V
M
=
Device Density
Package Device Grade or
Wafer/Die Thickness
01 = 1-Kbit
02 = 2-Kbit
U
=
=
=
Green, matte Sn lead finish,
Industrial temperature range
(-40˚C to +85˚C)
Device Revision
H
Green, NiPdAu lead finish,
Industrial temperature range
(-40˚C to +85˚C)
11
11mil wafer thickness
Package Option
SS = JEDEC SOIC
X
= TSSOP
MA = UDFN
PDIP
ST = SOT23
VFBGA
WWU = Wafer Unsawn
P
=
C
=
12
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
11. Part Markings
AT24C01C and AT24C02C: Package Marking Information
8-lead TSSOP
8-lead SOIC
8-lead PDIP
ATHYWW
###% @
ATMLUYWW
###%
AAAAAAAA
ATMLHYWW
###%
AAAAAAAA
@
@
AAAAAAA
8-pad UDFN
5-lead SOT-23
8-ball VFBGA
2.35 x 3.73 mm Body
2.0 x 3.0 mm Body
###
###U
##@%U
YMXX
@YMXX
H%@
YXX
Note 1:
Note 2: Package drawings are not to scale
Note 3: For SOT23 package with date codes before 7B, the bottom line (YMXX) is marked on the bottom side and there is no Country of Assembly (
designates pin 1
@
) mark on the top line.
Catalog Number Truncation
AT24C01C
AT24C02C
Truncation Code ###: 01C / ##: 1C
Truncation Code ###: 02C / ##: 2C
Date Codes
Voltages
Y = Year
6: 2016
7: 2017
8: 2018
9: 2019
M = Month
A: January
B: February
...
WW = Work Week of Assembly
% = Minimum Voltage
M: 1.7V min
0: 2020
1: 2021
2: 2022
3: 2023
02: Week 2
04: Week 4
...
L: December
52: Week 52
Country of Assembly
Lot Number
AAA...A = Atmel Wafer Lot Number
Grade/Lead Finish Material
@ = Country of Assembly
U: Industrial/Matte Tin/SnAgCu
H: Industrial/NiPdAu
Trace Code
Atmel Truncation
XX = Trace Code (Atmel Lot Numbers Correspond to Code)
Example: AA, AB.... YZ, ZZ
AT: Atmel
ATM: Atmel
ATML: Atmel
12/7/16
TITLE
DRAWING NO.
REV.
24C01-02CSM, AT24C01C and AT24C02C Package Marking
Information
Package Mark Contact:
DL-CSO-Assy_eng@atmel.com
24C01-02CSM
C
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
13
12. Ordering Information
Delivery Information
Operation
Range
Atmel Ordering Code
AT24C01C-SSHM-B
AT24C01C-SSHM-T
AT24C01C-XHM-B
Lead Finish
Package
Form
Quantity
Bulk (Tubes)
Tape and Reel
Bulk (Tubes)
100 per Tube
4,000 per Reel
100 per Tube
5,000 per Reel
5,000 per Reel
8S1
NiPdAu
(Lead-free/Halogen-free)
8X
AT24C01C-XHM-T
AT24C01C-MAHM-T
AT24C01C-MAHM-E
AT24C01C-PUM
Tape and Reel
Tape and Reel
Industrial
Temperature
(-40C to 85C)
8MA2
Tape and Reel 15,000 per Reel
8P3
Bulk (Tubes)
50 per Tube
Matte Tin
(Lead-free/Halogen-free)
AT24C01C-STUM-T
5TS1
Tape and Reel
5,000 per Reel
SnAgCu Ball
(Lead-free/Halogen-free)
AT24C01C-CUM-T
8U3-1
Tape and Reel
5,000 per Reel
AT24C01C-WWU11M(1)
N/A
Wafer Sale
Note 1
AT24C02C-SSHM-B
AT24C02C-SSHM-T
AT24C02C-XHM-B
AT24C02C-XHM-T
AT24C02C-MAHM-T
AT24C02C-MAHM-E
AT24C02C-PUM
Bulk (Tubes)
Tape and Reel
Bulk (Tubes)
100 per Tube
4,000 per Reel
100 per Tube
5,000 per Reel
5,000 per Reel
8S1
8X
NiPdAu
(Lead-free/Halogen-free)
Tape and Reel
Tape and Reel
Industrial
Temperature
(-40C to 85C)
8MA2
Tape and Reel 15,000 per Reel
8P3
Bulk (Tubes)
50 per Tube
Matte Tin
(Lead-free/Halogen-free)
AT24C02C-STUM-T
5TS1
Tape and Reel
5,000 per Reel
SnAgCu Ball
(Lead-free/Halogen-free)
AT24C02C-CUM-T
8U3-1
Tape and Reel
5,000 per Reel
AT24C02C-WWU11M(1)
N/A
Wafer Sale
Note 1
Note:
1. For Wafer sales, please contact Atmel Sales.
Package Type
8-lead, 0.300" wide, Plastic Dual Inline (PDIP)
8P3
8S1
8X
8-lead, 0.150" wide, Plastic Gull Wing Small Outline (JEDEC SOIC)
8-lead, 4.4mm body, Plastic Thin Shrink Small Outline (TSSOP)
8MA2
8-lead, 2.00mm x 3.00mm body, 0.50mm Pitch, Ultra Thin Dual Flat No Lead (UDFN)
5-lead, 2.90mm x 1.60mm body, Plastic Thin Shrink Small Outline (SOT23)
8-ball, die Ball Grid Array (VFBGA)
5TS1
8U3-1
14
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
13. Packaging Information
13.1 8S1 — 8-lead JEDEC SOIC
C
1
E
E1
L
N
Ø
TOP VIEW
END VIEW
e
b
COMMON DIMENSIONS
(Unit of Measure = mm)
A
MIN
1.35
0.10
MAX
1.75
0.25
NOM
–
–
NOTE
SYMBOL
A1
A
A1
b
0.31
0.17
4.80
3.81
5.79
–
0.51
0.25
5.05
3.99
6.20
C
D
E1
E
e
–
–
D
–
–
SIDE VIEW
Notes: This drawing is for general information only.
Refer to JEDEC Drawing MS-012, Variation AA
for proper dimensions, tolerances, datums, etc.
1.27 BSC
L
0.40
0°
–
–
1.27
8°
Ø
6/22/11
DRAWING NO. REV.
8S1
TITLE
GPC
8S1, 8-lead (0.150” Wide Body), Plastic Gull Wing
Small Outline (JEDEC SOIC)
SWB
G
Package Drawing Contact:
packagedrawings@atmel.com
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
15
13.2 8X — 8-lead TSSOP
C
1
Pin 1 indicator
this corner
E1
E
L1
N
L
Top View
End View
A
b
A1
COMMON DIMENSIONS
(Unit of Measure = mm)
e
A2
D
SYMBOL
MIN
-
NOM
-
MAX
1.20
0.15
1.05
3.10
NOTE
2, 5
A
Side View
A1
A2
D
0.05
0.80
2.90
-
Notes: 1. This drawing is for general information only.
1.00
Refer to JEDEC Drawing MO-153, Variation AA, for proper
dimensions, tolerances, datums, etc.
3.00
2. Dimension D does not include mold Flash, protrusions or gate
burrs. Mold Flash, protrusions and gate burrs shall not exceed
0.15mm (0.006in) per side.
E
6.40 BSC
4.40
E1
b
4.30
0.19
4.50
0.30
3, 5
4
3. Dimension E1 does not include inter-lead Flash or protrusions.
Inter-lead Flash and protrusions shall not exceed 0.25mm
(0.010in) per side.
4. Dimension b does not include Dambar protrusion.
Allowable Dambar protrusion shall be 0.08mm total in excess
of the b dimension at maximum material condition. Dambar
cannot be located on the lower radius of the foot. Minimum
space between protrusion and adjacent lead is 0.07mm.
5. Dimension D and E1 to be determined at Datum Plane H.
0.25
e
0.65 BSC
0.60
L
0.45
0.09
0.75
0.20
L1
C
1.00 REF
-
2/27/14
TITLE
GPC
TNR
DRAWING NO.
REV.
8X, 8-lead 4.4mm Body, Plastic Thin
Shrink Small Outline Package (TSSOP)
8X
E
Package Drawing Contact:
packagedrawings@atmel.com
16
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
13.3 8MA2 — 8-pad UDFN
E
1
8
7
6
5
Pin 1 ID
2
3
4
D
C
TOP VIEW
E2
SIDE VIEW
A2
A
A1
b (8x)
8
1
2
3
4
COMMON DIMENSIONS
(Unit of Measure = mm)
7
6
5
Pin#1 ID
D2
MIN
0.50
MAX
0.60
NOM
0.55
NOTE
SYMBOL
A
A1
A2
D
0.0
-
0.02
-
0.05
0.55
2.10
1.60
3.10
1.40
0.30
e (6x)
L (8x)
BOTTOM VIEW
K
1.90
1.40
2.90
1.20
0.18
2.00
D2
E
1.50
3.00
Notes:
1. This drawing is for general information only. Refer to
Drawing MO-229, for proper dimensions, tolerances,
datums, etc.
E2
b
1.30
0.25
3
2. The Pin #1 ID is a laser-marked feature on Top View.
3. Dimensions b applies to metallized terminal and is
measured between 0.15 mm and 0.30 mm from the
terminal tip. If the terminal has the optional radius on
the other end of the terminal, the dimension should
not be measured in that radius area.
C
1.52 REF
0.35
L
0.30
0.20
0.40
-
e
0.50 BSC
-
K
4. The Pin #1 ID on the Bottom View is an orientation
feature on the thermal pad.
11/26/14
TITLE
DRAWING NO.
REV.
GPC
8MA2, 8-pad 2 x 3 x 0.6mm Body, Thermally
YNZ
8MA2
G
Package Drawing Contact:
packagedrawings@atmel.com
Enhanced Plastic Ultra Thin Dual Flat No-Lead
Package (UDFN)
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
17
13.4 8P3 — 8-lead PDIP
E
1
E1
.381
Gage Plane
N
Top View
c
eA
End View
COMMON DIMENSIONS
(Unit of Measure = mm)
D
e
MIN
MAX
5.334
-
NOM
-
NOTE
SYMBOL
D1
A2 A
A
-
2
A1
A2
b
0.381
2.921
0.356
1.143
0.762
0.203
9.017
0.127
7.620
6.096
-
3.302
0.457
1.524
0.991
0.254
9.271
0.000
7.874
6.350
2.540 BSC
7.620 BSC
3.302
4.953
0.559
1.778
1.143
0.356
10.160
0.000
8.255
7.112
5
6
6
b2
b3
c
A1
b2
D
3
3
4
3
L
b3
D1
E
m
b
4 PLCS
0.254
C
v
E1
e
Side View
eA
L
4
2
2.921
3.810
Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information.
2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3.
3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch.
4. E and eA measured with the leads constrained to be perpendicular to datum.
5. Pointed or rounded lead tips are preferred to ease insertion.
6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm).
07/31/14
TITLE
GPC
PTC
DRAWING NO.
8P3
REV.
E
8P3, 8-lead, 0.300” Wide Body, Plastic Dual
In-line Package (PDIP)
Package Drawing Contact:
packagedrawings@atmel.com
18
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
13.5 5TS1 — 5-lead SOT23
e1
C
4
5
E1
C
L
E
L1
3
1
2
TOP VIEW
END VIEW
b
A2
A
SEATING
PLANE
A1
e
D
SIDE VIEW
COMMON DIMENSIONS
(Unit of Measure = mm)
1. Dimension D does not include mold flash, protrusions or gate burrs. Mold flash,
MIN
MAX
NOM
NOTE
protrusions or gate burrs shall not exceed 0.15 mm per end. Dimension E1 does
not include interlead flash or protrusion. Interlead flash or protrusion shall not
exceed 0.15 mm per side.
SYMBOL
A
A1
A2
c
D
E
E1
L1
e
e1
b
-
-
-
1.00
0.10
2. The package top may be smaller than the package bottom. Dimensions D and E1
are determined at the outermost extremes of the plastic body exclusive of mold
flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch
between the top and bottom of the plastic body.
3. These dimensions apply to the flat section of the lead between 0.08 mm and 0.15
mm from the lead tip.
4. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion
shall be 0.08 mm total in excess of the "b" dimension at maximum material
condition. The dambar cannot be located on the lower radius of the foot. Minimum
space between protrusion and an adjacent lead shall not be less than 0.07 mm.
0.00
0.70 0.90 1.00
0.08
-
0.20
3
2.90 BSC
2.80 BSC
1.60 BSC
0.60 REF
0.95 BSC
1.90 BSC
-
1,2
1,2
1,2
This drawing is for general information only. Refer to JEDEC
Drawing MO-193, Variation AB for additional information.
0.30
0.50
3,4
5/31/12
REV.
TITLE
GPC
TSZ
DRAWING NO.
5TS1
5TS1, 5-lead 1.60mm Body, Plastic Thin
Shrink Small Outline Package (Shrink SOT)
D
Package Drawing Contact:
packagedrawings@atmel.com
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
19
13.6 8U3-1 — 8-ball VFBGA
E
D
2.
b
PIN 1 BALL PAD CORNER
A1
A2
A
TOP VIEW
SIDE VIEW
PIN 1 BALL PAD CORNER
4
3
1
2
d
(d1)
6
5
8
7
COMMON DIMENSIONS
(Unit of Measure - mm)
e
(e1)
SYMBOL
NOM
MIN
MAX
NOTE
2
0.73
0.09
0.40
0.20
0.79
0.85
0.19
0.50
0.30
A
A1
A2
b
BOTTOM VIEW
8 SOLDER BALLS
0.14
0.45
Notes:
0.25
1. This drawing is for general information only.
1.50 BSC
2.0 BSC
0.50 BSC
0.25 REF
1.00 BSC
0.25 REF
D
E
2. Dimension ‘b’ is measured at maximum solder ball diameter.
3. Solder ball composition shall be 95.5Sn-4.0Ag-.5Cu.
e
e1
d
d1
6/11/13
REV.
TITLE
DRAWING NO.
8U3-1
GPC
GXU
8U3-1, 8-ball, 1.50mm x 2.00mm body, 0.50mm pitch,
Very Thin, Fine-Pitch Ball Grid Array Package (VFBGA)
F
Package Drawing Contact:
packagedrawings@atmel.com
20
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
14. Revision History
Doc. Rev.
Date
Comments
Part marking SOT23:
8700H
12/2016
- Moved backside mark (YMXX) to front side line2.
- Added @ = Country of Assembly.
Add the UDFN extended quantity option.
8700G
8700F
01/2015
06/2012
Update part markings, package drawings, ordering information, template, and
reorganize.
Correct ordering codes:
- AT24C01C-WWU11, Die Sale to AT24C01C-WWU11M, Wafer Sale.
- AT24C02C-WWU11, Die Sale to AT24C02C-WWU11M, Wafer Sale.
Remove WDT from ordering code detail.
Update Atmel logos and disclaimer page.
Update datasheet template.
Add AT24C01C to document.
Electrical performance improvements:
- Reduce all ISB from legacy values
- Increase 1MHz frequency range to include 2.5V operation.
8700E
8700D
05/2012
08/2010
Update package drawings to latest versions (where applicable) and selected waveforms.
Change AT24C02C-XHM Part Marking from C02CM@ to 02CM @.
Ordering Information:
- Change Atmel AT24C02C-TSUM-T to Atmel AT24C02C-STUM-T.
- Change Atmel AT24C02CY6-MAHM-T to Atmel AT24C02C-MAHM-T.
- Change Atmel AT24C02CU3-CUM-T to Atmel AT24C02C-CUM-T.
Catalog numbering scheme, change TS = SOT23 to ST = SOT23.
Part marking SOT23:
- Change 2CMWU to 2CMBU.
- Change W = Write Protection Feature to B = Write Protection.
8700C
07/2010
Part marking PDIP and SOIC: Added @ = Country of Assembly.
Part marking TSSOP: Replaced and removed bottom mark.
Part marking UDFN: Added HM@.
Remove preliminary status.
Change tI Max 40 to 50 in Table AC Characteristics.
8700B
8700A
02/2010
12/2009
Correct catalog numbering scheme and ordering information.
Initial document release.
AT24C01C/02C [DATASHEET]
Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016
21
X X
X X X X
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
© 2015 Atmel Corporation. / Rev.: Atmel-8700H-SEEPROM-AT24C01C-02C-Datasheet_122016.
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation in U.S. and
other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.
相关型号：
AT24C02CY6-MAHM-T
EEPROM, 256KX8, Serial, CMOS, PDSO8, 2.00 X 3.00 MM, 0.50 MM PITCH, GREEN, MO-229, UDFN-8
MICROCHIP
©2020 ICPDF网 联系我们和版权申明