ATMEGA64A-ANR [MICROCHIP]
IC MCU 8BIT 64KB FLASH 64TQFP;
| 型号： | ATMEGA64A-ANR |
| 厂家： | 
MICROCHIP |
| 描述： | IC MCU 8BIT 64KB FLASH 64TQFP 时钟 微控制器 外围集成电路 |
| 文件： | 总20页 (文件大小：285K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
8-bit AVR Micrcontroller
ATmega64A
DATASHEET SUMMARY
Introduction
The Atmel® ATmega64A is a low-power CMOS 8-bit microcontroller based
on the AVR® enhanced RISC architecture. By executing powerful instructions
in a single clock cycle, the ATmega64A achieves throughputs close to
1MIPS per MHz. This empowers system designer to optimize the device for
power consumption versus processing speed.
Features
•
•
High-performance, Low-power Atmel AVR 8-bit Microcontroller
Advanced RISC Architecture
–
–
130 Powerful Instructions - Most Single-clock Cycle Execution
32 × 8 General Purpose Working Registers + Peripheral Control
Registers
–
–
–
Fully Static Operation
Up to 16MIPS Throughput at 16MHz
On-chip 2-cycle Multiplier
•
High Endurance Non-volatile Memory segments
–
64Kbytes of In-System Self-programmable Flash program
memory
–
–
–
–
–
2Kbytes EEPROM
4Kbytes Internal SRAM
Write/Erase cycles: 10,000 Flash/100,000 EEPROM
Data retention: 20 years at 85°C/100 years at 25°C(1)
Optional Boot Code Section with Independent Lock Bits
•
•
In-System Programming by On-chip Boot Program
True Read-While-Write Operation
–
–
–
Up to 64 Kbytes Optional External Memory Space
Programming Lock for Software Security
SPI Interface for In-System Programming
This is a summary document. A
complete document is available
on our Web site at
•
JTAG (IEEE std. 1149.1 Compliant) Interface
–
–
Boundary-scan Capabilities According to the JTAG Standard
Extensive On-chip Debug Support
www.atmel.com
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
–
Programming of Flash, EEPROM, Fuses and Lock Bits through the JTAG Interface
®
•
•
Atmel QTouch library support
–
–
–
Capacitive touch buttons, sliders and wheels
Atmel QTouch and QMatrix acquisition
Up to 64 sense channels
Peripheral Features
–
–
Two 8-bit Timer/Counters with Separate Prescalers and Compare Modes
Two Expanded 16-bit Timer/Counters with Separate Prescaler, Compare Mode and Capture
Mode
–
–
–
–
–
Real Time Counter with Separate Oscillator
Two 8-bit PWM Channels
6 PWM Channels with Programmable Resolution from 1 to 16 Bits
Output Compare Modulator
8-channel, 10-bit ADC
•
•
•
8 Single-ended Channels
7 Differential Channels
2 Differential Channels with Programmable Gain at 1x, 10x, or 200x
–
–
–
–
–
Byte-oriented Two-wire Serial Interface
Dual Programmable Serial USARTs
Master/Slave SPI Serial Interface
Programmable Watchdog Timer with On-chip Oscillator
On-chip Analog Comparator
•
Special Microcontroller Features
–
–
–
–
Power-on Reset and Programmable Brown-out Detection
Internal Calibrated RC Oscillator
External and Internal Interrupt Sources
Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby, and
Extended Standby
–
–
–
Software Selectable Clock Frequency
ATmega103 Compatibility Mode Selected by a Fuse
Global Pull-up Disable
•
I/O and Packages
–
–
53 Programmable I/O Lines
64-lead TQFP and 64-pad QFN/MLF
•
•
Operating Voltages
2.7 - 5.5V
Speed Grades
0 - 16MHz
–
–
Atmel ATmega64A [DATASHEET]
2
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
Table of Contents
Introduction......................................................................................................................1
Features.......................................................................................................................... 1
1. Description.................................................................................................................4
2. Configuration Summary.............................................................................................5
3. Ordering Information..................................................................................................6
4. Block Diagram........................................................................................................... 7
5. ATmega103 and ATmega64A Compatibility.............................................................. 8
5.1. ATmega103 Compatibility Mode...................................................................................................8
6. Pin Configurations..................................................................................................... 9
6.1. Pin Descriptions............................................................................................................................9
7. Resources................................................................................................................12
8. Data Retention.........................................................................................................13
9. About Code Examples.............................................................................................14
10. Capacitive Touch Sensing....................................................................................... 15
11. Packaging Information.............................................................................................16
11.1. 64A.............................................................................................................................................16
11.2. 64M1...........................................................................................................................................17
12. Errata.......................................................................................................................18
12.1. ATmega64A Rev. D....................................................................................................................18
1.
Description
The AVR core combines a rich instruction set with 32 general purpose working registers. All the 32
registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to
be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code
efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers.
The ATmega64A provides the following features: 64 Kbytes In-System Programmable Flash with Read-
While- Write capabilities, 2 Kbytes EEPROM, 4 Kbytes SRAM, 53 general purpose I/O lines, 32 general
purpose working registers, Real Time Counter (RTC), four flexible Timer/Counters with compare modes
and PWM, two USARTs, a byte oriented Two-wire Serial Interface, an 8-channel, 10-bit ADC with optional
differential input stage with programmable gain, programmable Watchdog Timer with internal Oscillator,
an SPI serial port, IEEE std. 1149.1 compliant JTAG test interface, also used for accessing the On-chip
Debug system and programming, and six software selectable power saving modes. The Idle mode stops
the CPU while allowing the SRAM, Timer/Counters, SPI port, and interrupt system to continue
functioning. The Power-down mode saves the register contents but freezes the Oscillator, disabling all
other chip functions until the next interrupt or Hardware Reset. In Power-save mode, the asynchronous
timer continues to run, allowing the user to maintain a timer base while the rest of the device is sleeping.
The ADC Noise Reduction mode stops the CPU and all I/O modules except asynchronous timer and
ADC, to minimize switching noise during ADC conversions. In Standby mode, the crystal/resonator
Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with
low power consumption. In Extended Standby mode, both the main Oscillator and the asynchronous timer
continue to run.
The device is manufactured using Atmel’s high-density non-volatile memory technology. The On-chip ISP
Flash allows the program memory to be reprogrammed In-System through an SPI serial interface, by a
conventional nonvolatile memory programmer, or by an On-chip Boot program running on the AVR core.
The Boot Program can use any interface to download the Application Program in the Application Flash
memory. Software in the Boot Flash section will continue to run while the Application Flash section is
updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System
Self-Programmable Flash on a monolithic chip, the Atmel ATmega64A is a powerful microcontroller that
provides a highly-flexible and cost-effective solution to many embedded control applications.
The ATmega64A AVR is supported with a full suite of program and system development tools including: C
compilers, macro assemblers, program debugger/simulators, in-circuit emulators, and evaluation kits.
Atmel ATmega64A [DATASHEET]
4
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
2.
Configuration Summary
Features
ATmega64A
Pin count
64
Flash (KB)
64
SRAM (KB)
4
EEPROM (KB)
General Purpose I/O pins
SPI
2
53
1
TWI (I2C)
1
USART
2
ADC
10-bit, up to 76.9ksps (15ksps at max resolution)
ADC channels
AC propagation delay
8-bit Timer/Counters
16-bit Timer/Counters
PWM channels
RC Oscillator
6 (8 in TQFP and QFN/MLF packages)
Typ 400ns
2
1
8
+/-3%
VREF Bandgap
Operating voltage
Max operating frequency
Temperature range
JTAG
2.7 - 5.5V
16MHz
-55°C to +125°C
Yes
Atmel ATmega64A [DATASHEET]
5
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
3.
Ordering Information
Speed (MHz) Power Supply Ordering Code(2)
Package(1) Operational Range
ATmega64A-AU
ATmega64A-AUR(3)
64A
64A
Industrial (-40oC to 85oC)
ATmega64A-MU
64M1
ATmega64A-MUR(3)
64M1
16
2.7 - 5.5V
ATmega64A-AN
ATmega64A-ANR(3)
64A
64A
Extended (-40oC to 105oC)(4)
ATmega64A-MN
64M1
ATmega64A-MNR(3)
64M1
Note:ꢀ
1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for
detailed ordering information and minimum quantities.
2. Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances
(RoHS directive). Also Halide free and fully Green.
3. Tape and Reel
4. See characterization specifications at 105°C
Package Type
64A 64-lead, Thin (1.0mm) Plastic Gull Wing Quad Flat Package (TQFP)
64M1 64-pad, 9 x 9 x 1.0mm body, lead pitch 0.50mm, Quad Flat No-Lead/Micro Lead Frame Package
(QFN/MLF)
Atmel ATmega64A [DATASHEET]
6
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
4.
Block Diagram
Figure 4-1ꢀBlock Diagram
SRAM
FLASH
TCK
TMS
TDI
CPU
OCD
JTAG
TDO
PARPROG
SERPROG
NVM
programming
PEN
PDI
PDO
SCK
EEPROM
EEPROMIF
AD[7:0]
ExtMem
A[15:8]
RD/WR/ALE
Clock generation
D
A
T
A
B
U
S
XTAL1
8MHz
Crystal Osc
8MHz
Calib RC
Power
management
and clock
control
PA[7:0]
PB[7:0]
PC[7:0]
PD[7:0]
PE[7:0]
PF[7:0]
PG[4:0]
12MHz
External
RC Osc
XTAL2
External
clock
I/O
PORTS
TOSC1
32.768kHz
XOSC
1MHz int
osc
TOSC2
ExtInt
INT[7:0]
VCC
Power
Watchdog
Timer
Supervision
POR/BOD &
RESET
ADC[7:0]
AREF
RESET
GND
ADC
AC
Internal
AIN0
AIN1
ACO
Reference
ADCMUX
MISO
MOSI
SCK
SS
TC 0
SPI
OC0
(8-bit async)
OC1A/B/C
T1
ICP1
SDA
SCL
TC 1
TWI
(16-bit)
RxD0
TxD0
XCK0
T2
OC2
TC 2
USART 0
USART 1
(8-bit)
RxD1
TxD1
XCK1
OC3A/B
T3
ICP3
TC 3
(16-bit)
Atmel ATmega64A [DATASHEET]
7
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
5.
ATmega103 and ATmega64A Compatibility
The ATmega64A is a highly complex microcontroller where the number of I/O locations supersedes the
64 I/O locations reserved in the AVR instruction set. To ensure backward compatibility with the
ATmega103, all I/O locations present in ATmega103 have the same location in ATmega64A. Most
additional I/O locations are added in an Extended I/O space starting from 0x60 to 0xFF, (that is, in the
ATmega103 internal RAM space). These locations can be reached by using LD/LDS/LDD and
ST/STS/STD instructions only, not by using IN and OUT instructions. The relocation of the internal RAM
space may still be a problem for ATmega103 users. Also, the increased number of interrupt vectors might
be a problem if the code uses absolute addresses. To solve these problems, an ATmega103 compatibility
mode can be selected by programming the fuse M103C. In this mode, none of the functions in the
Extended I/O space are in use, so the internal RAM is located as in ATmega103. Also, the Extended
Interrupt vectors are removed.
The Atmel AVR ATmega64A is 100% pin compatible with ATmega103, and can replace the ATmega103
on current Printed Circuit Boards. The application note “Replacing ATmega103 by ATmega64A” describes
what the user should be aware of replacing the ATmega103 by an ATmega64A.
5.1.
ATmega103 Compatibility Mode
By programming the M103C fuse, the ATmega64A will be compatible with the ATmega103 regards to
RAM, I/O pins and interrupt vectors as described above. However, some new features in ATmega64A are
not available in this compatibility mode, these features are listed below:
•
One USART instead of two, Asynchronous mode only. Only the eight least significant bits of the
Baud Rate Register is available.
•
One 16 bits Timer/Counter with two compare registers instead of two 16-bit Timer/Counters with
three compare registers.
•
•
•
•
•
•
•
Two-wire serial interface is not supported.
Port C is output only.
Port G serves alternate functions only (not a general I/O port).
Port F serves as digital input only in addition to analog input to the ADC.
Boot Loader capabilities is not supported.
It is not possible to adjust the frequency of the internal calibrated RC Oscillator.
The External Memory Interface can not release any Address pins for general I/O, neither configure
different wait-states to different External Memory Address sections.
•
•
•
•
•
In addition, there are some other minor differences to make it more compatible to ATmega103:
Only EXTRF and PORF exists in MCUCSR.
Timed sequence not required for Watchdog Time-out change.
External Interrupt pins 3 - 0 serve as level interrupt only.
USART has no FIFO buffer, so data overrun comes earlier.
Unused I/O bits in ATmega103 should be written to 0 to ensure same operation in ATmega64A.
Atmel ATmega64A [DATASHEET]
8
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
6.
Pin Configurations
Figure 6-1ꢀPinout ATmega64A
Power
Ground
Programming/debug
Digital
Analog
Crystal/Osc
External Memory
PEN
(RXD0/PDI) PE0
(TXD0/PDO) PE1
(XCK0/AIN0) PE2
(OC3A/AIN1) PE3
(OC3B/INT4) PE4
(OC3C/INT5) PE5
(T3/INT6) PE6
(ICP3/INT7) PE7
(SS) PB0
1
2
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
PA3 (AD3)
PA4 (AD4)
PA5 (AD5)
PA6 (AD6)
PA7 (AD7)
PG2 (ALE)
PC7 (A15)
PC6 (A14)
PC5 (A13)
PC4 (A12)
PC3 (A11)
PC2 (A10)
PC1 (A9)
3
4
5
6
7
8
9
10
11
12
13
14
15
16
(SCK) PB1
(MOSI) PB2
(MISO) PB3
(OC0) PB4
PC0 (A8)
(OC1A) PB5
PG1 (RD)
PG0 (WR)
(OC1B) PB6
Note:ꢀ The Pinout figure applies to both TQFP and MLF packages. The bottom pad under the QFN/MLF
package should be soldered to ground.
6.1.
Pin Descriptions
6.1.1.
VCC
Digital supply voltage.
Atmel ATmega64A [DATASHEET]
9
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
6.1.2.
6.1.3.
GND
Ground.
Port A (PA7:PA0)
Port A is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port A
output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs,
Port A pins that are externally pulled low will source current if the pull-up resistors are activated. The Port
A pins are tristated when a reset condition becomes active, even if the clock is not running.
Port A also serves the functions of various special features of the ATmega64A as listed in Alternate
Functions of Port A.
6.1.4.
Port B (PB7:PB0)
Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B
output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs,
Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port
B pins are tristated when a reset condition becomes active, even if the clock is not running.
Port B also serves the functions of various special features of the ATmega64A as listed in Alternate
Functions of Port B.
6.1.5.
Port C (PC7:PC0)
Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port C
output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs,
Port C pins that are externally pulled low will source current if the pull-up resistors are activated. The Port
C pins are tristated when a reset condition becomes active, even if the clock is not running.
Port C also serves the functions of special features of the ATmega64A as listed in Alternate Functions of
Port C. In ATmega103 compatibility mode, Port C is output only, and the port C pins are not tri-stated
when a reset condition becomes active.
Note:ꢀ The Atmel AVR ATmega64A is by default shipped in ATmega103 compatibility mode. Thus, if the
parts are not programmed before they are put on the PCB, PORTC will be output during first power up,
and until the ATmega103 compatibility mode is disabled.
6.1.6.
6.1.7.
6.1.8.
Port D (PD7:PD0)
Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D
output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs,
Port D pins that are externally pulled low will source current if the pull-up resistors are activated. The Port
D pins are tristated when a reset condition becomes active, even if the clock is not running.
Port D also serves the functions of various special features of the ATmega64A as listed in Alternate
Functions of Port D.
Port E (PE7:PE0)
Port E is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port E
output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs,
Port E pins that are externally pulled low will source current if the pull-up resistors are activated. The Port
E pins are tristated when a reset condition becomes active, even if the clock is not running.
Port E also serves the functions of various special features of the ATmega64A as listed in Alternate
Functions of Port E.
Port F (PF7:PF0)
Port F serves as the analog inputs to the A/D Converter.
Atmel ATmega64A [DATASHEET]
10
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
Port F also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used. Port pins can
provide internal pull-up resistors (selected for each bit). The Port F output buffers have symmetrical drive
characteristics with both high sink and source capability. As inputs, Port F pins that are externally pulled
low will source current if the pull-up resistors are activated. The Port F pins are tri-stated when a reset
condition becomes active, even if the clock is not running. If the JTAG interface is enabled, the pull-up
resistors on pins PF7(TDI), PF5(TMS), and PF4(TCK) will be activated even if a Reset occurs.
The TDO pin is tri-stated unless TAP states that shift out data are entered.
Port F also serves the functions of the JTAG interface.
In ATmega103 compatibility mode, Port F is an input Port only.
6.1.9.
Port G (PG4:PG0)
Port G is a 5-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port G
output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs,
Port G pins that are externally pulled low will source current if the pull-up resistors are activated. The Port
G pins are tristated when a reset condition becomes active, even if the clock is not running.
Port G also serves the functions of various special features.
The port G pins are tri-stated when a reset condition becomes active, even if the clock is not running.
In Atmel AVR ATmega103 compatibility mode, these pins only serves as strobes signals to the external
memory as well as input to the 32kHz Oscillator, and the pins are initialized to PG0 = 1, PG1 = 1, and
PG2 = 0 asynchronously when a reset condition becomes active, even if the clock is not running. PG3
and PG4 are oscillator pins.
6.1.10. RESET
Reset input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if
the clock is not running. The minimum pulse length is given in System and Reset Characteristics. Shorter
pulses are not guaranteed to generate a reset.
6.1.11. XTAL1
Input to the inverting Oscillator amplifier and input to the internal clock operating circuit.
6.1.12. XTAL2
Output from the inverting Oscillator amplifier.
6.1.13. AVCC
AVCC is the supply voltage pin for Port F and the A/D Converter. It should be externally connected to VCC
even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-pass filter.
,
6.1.14. AREF
AREF is the analog reference pin for the A/D Converter.
6.1.15. PEN
PEN is a programming enable pin for the SPI Serial Programming mode, and is internally pulled high. By
holding this pin low during a Power-on Reset, the device will enter the SPI Serial Programming mode.
PEN has no function during normal operation.
Atmel ATmega64A [DATASHEET]
11
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
7.
Resources
A comprehensive set of development tools, application notes and datasheets are available for download
on http://www.atmel.com/avr.
Atmel ATmega64A [DATASHEET]
12
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
8.
Data Retention
Reliability Qualification results show that the projected data retention failure rate is much less than 1 PPM
over 20 years at 85°C or 100 years at 25°C.
Atmel ATmega64A [DATASHEET]
13
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
9.
About Code Examples
This datasheet contains simple code examples that briefly show how to use various parts of the device.
These code examples assume that the part specific header file is included before compilation. Be aware
that not all C compiler vendors include bit definitions in the header files and interrupt handling in C is
compiler dependent. Please confirm with the C compiler documentation for more details.
For I/O registers located in extended I/O map, “IN”, “OUT”, “SBIS”, “SBIC”, “CBI”, and “SBI” instructions
must be replaced with instructions that allow access to extended I/O. Typically “LDS” and “STS”
combined with “SBRS”, “SBRC”, “SBR”, and “CBR”.
Atmel ATmega64A [DATASHEET]
14
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
10.
Capacitive Touch Sensing
The Atmel QTouch Library provides a simple to use solution to realize touch sensitive interfaces on most
Atmel AVR microcontrollers. The QTouch Library includes support for the QTouch and QMatrix®
acquisition methods.
Touch sensing can be added to any application by linking the appropriate Atmel QTouch Library for the
AVR Microcontroller. This is done by using a simple set of APIs to define the touch channels and sensors,
and then calling the touch sensing API’s to retrieve the channel information and determine the touch
sensor states.
The QTouch Library is FREE and downloadable from the Atmel website at the following location:
www.atmel.com/qtouchlibrary. For implementation details and other information, refer to the Atmel
QTouch Library User Guide - also available for download from the Atmel website.
Atmel ATmega64A [DATASHEET]
15
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
11.
Packaging Information
11.1. 64A
PIN1
B
e
PIN1 IDENTIFIER
E1
E
D1
D
C
0°~7°
A2
A
A1
L
COMMONDIMENSIONS
(Unit of measure = mm)
MIN
–
MAX
1.20
NOM
–
NOTE
SYMBOL
A
A1
A2
D
0.05
0.95
15.75
13.90
15.75
13.90
–
0.15
1.00
16.00
14.00
16.00
14.00
0.45
–
1.05
16.25
14.10
16.25
14.10
D1
E
Note 2
Note 2
Notes:
E1
B
1.This package conforms to JEDECreference MS-026,Variation AEB.
2. Dimensions D1 and E1 do not include mold protrusion. Allowable
0.30–
protrusion is 0.25mm per side. Dimensions D1 and E1 are maximum
plastic body size dimensions including mold mismatch.
3. Lead coplanarity is 0.10mm maximum.
C
0.09
0.45
0.20
0.75
L
–
e
0.80 TYP
2010-10-20
TITLE
DRAWINGNO.
REV.
2325 Orchard Parkway
San Jose, CA 95131
64A, 64-lead, 14 x 14mm Body Size, 1.0mm BodyThickness,
0.8mm Lead Pitch,Thin Prof le Plastic Quad Flat Package (TQFP)
64A
C
Atmel ATmega64A [DATASHEET]
16
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
11.2. 64M1
D
Marked Pin# 1 I D
E
SE ATINGPLAN
E
C
A1
TOP VIE W
A
K
0.08
C
L
Pin #1 Co rner
Option A
SIDEVIEW
D2
Pin #1
Triangle
1
2
3
COMMONDIMENSIONS
(Unit of Measure = mm)
MIN
0.80
–
MAX
1.00
0.05
0.30
9.10
NOM
0.90
0.02
0.25
9.00
NOTE
SYMBOL
E2
Option B
A
A1
b
Pin #1
Cham fer
(C0.30)
0.18
8.90
D
D2
E
5.20
8.90
5.40
9.00
5.60
9.10
K
Option C
Pin #1
Notch
(0.20 R)
e
b
E2
e
5.20
5.40
0.50 BSC
0.40
5.60
BOTTOMVIE W
L
0.35
1.25
0.45
1.55
K
1.40
Notes:
1 . JEDECStandard MO-220, (S
AWSingulation) Fig . 1,VMM D.
2 . Dimension and tole rance con form to ASMEY14.5M-1994
.
2010-10-19
TITLE
DRAWINGN O.
64M1
RE V.
H
2325 Orchard Parkway
San Jos e, CA 9513 1
64M1 , 64-pad, 9 x 9 x 1.0 mm Bod y, Lead Pitch 0.50 mm
5.40 mm Exposed Pad, Micro Lead Frame Package (MLF)
,
Atmel ATmega64A [DATASHEET]
17
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
12.
Errata
The revision letter in this section refers to the revision of the ATmega64A device.
12.1. ATmega64A Rev. D
•
•
•
•
•
•
First Analog Comparator conversion may be delayed
Interrupts may be lost when writing the timer registers in the asynchronous timer
Stabilizing time needed when changing XDIV Register
Stabilizing time needed when changing OSCCAL Register
IDCODE masks data from TDI input
Reading EEPROM by using ST or STS to set EERE bit triggers unexpected interrupt request
1. First Analog Comparator conversion may be delayed
If the device is powered by a slow rising VCC, the first Analog Comparator conversion will take
longer than expected on some devices.
Problem Fix/Workaround
When the device has been powered or reset, disable then enable the Analog Comparator before
the first conversion.
2. Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem Fix/Workaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor 0x00
before writing to the asynchronous Timer Control Register (TCCRx), asynchronous Timer Counter
Register (TCNTx), or asynchronous Output Compare Register (OCRx).
3. Stabilizing time needed when changing XDIV Register
After increasing the source clock frequency more than 2% with settings in the XDIV register, the
device may execute some of the subsequent instructions incorrectly.
Problem Fix/Workaround
The NOP instruction will always be executed correctly also right after a frequency change. Thus,
the next 8 instructions after the change should be NOP instructions. To ensure this, follow this
procedure:
3.1.
3.2.
3.3.
3.4.
Clear the I bit in the SREG Register.
Set the new pre-scaling factor in XDIV register.
Execute 8 NOP instructions
Set the I bit in SREG
This will ensure that all subsequent instructions will execute correctly.
Assembly Code Example:
CLI
OUT
NOP
NOP
NOP
; clear global interrupt enable
; set new prescale value
; no operation
XDIV, temp
; no operation
; no operation
Atmel ATmega64A [DATASHEET]
18
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
NOP
NOP
NOP
NOP
NOP
SEI
; no operation
; no operation
; no operation
; no operation
; no operation
; set global interrupt enable
4. Stabilizing time needed when changing OSCCAL Register
After increasing the source clock frequency more than 2% with settings in the OSCCAL register, the
device may execute some of the subsequent instructions incorrectly.
Problem Fix/Workaround
The behavior follows errata number 3., and the same Fix / Workaround is applicable on this errata.
5. IDCODE masks data from TDI input
The JTAG instruction IDCODE is not working correctly. Data to succeeding devices are replaced by
all-ones during Update-DR.
Problem Fix/Workaround
–
–
If ATmega64A is the only device in the scan chain, the problem is not visible.
Select the Device ID Register of the ATmega64A by issuing the IDCODE instruction or by
entering the Test-Logic-Reset state of the TAP controller to read out the contents of its Device
ID Register and possibly data from succeeding devices of the scan chain. Issue the BYPASS
instruction to the ATmega64A while reading the Device ID Registers of preceding devices of
the boundary scan chain.
–
If the Device IDs of all devices in the boundary scan chain must be captured simultaneously,
the ATmega64A must be the first device in the chain.
6. Reading EEPROM by using ST or STS to set EERE bit triggers unexpected interrupt request.
Reading EEPROM by using the ST or STS command to set the EERE bit in the EECR register
triggers an unexpected EEPROM interrupt request.
Problem Fix/Workaround
Always use OUT or SBI to set EERE in EECR.
Atmel ATmega64A [DATASHEET]
19
Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
©
2015 Atmel Corporation. / Rev.: Atmel-8160ES-8-bit AVR Micrcontroller_Datasheet_Summary-09/2015
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, AVR®, and others are registered trademarks or trademarks of Atmel Corporation in
U.S. and other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any
intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND
CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED
OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY,
FITNESS FOR
A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS
INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to
update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive
applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any
applications where the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without
an Atmel officer's specific written consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the
operation of nuclear facilities and weapons systems. Atmel products are not designed nor intended for use in military or aerospace applications or environments
unless specifically designated by Atmel as military-grade. Atmel products are not designed nor intended for use in automotive applications unless specifically
designated by Atmel as automotive-grade.
相关型号：
ATMEGA64A-AUR
RISC Microcontroller, 8-Bit, FLASH, AVR RISC CPU, 16MHz, CMOS, PQFP64, 14 X 14 MM, 1 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, MS-026AEB, TQFP-64
ATMEL
ATMEGA64A-AURSL514
RISC Microcontroller, 8-Bit, FLASH, 16MHz, CMOS, PQFP64, 14 X 14 MM, 1 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, MS-026AEB, TQFP-64
ATMEL
ATMEGA64A-MUR
RISC Microcontroller, 8-Bit, FLASH, AVR RISC CPU, 16MHz, CMOS, 9 X 9 MM, 1 MM HEIGHT, 0.50 MM PITCH, GREEN, MO-220VMMD, MLF-64
ATMEL
©2020 ICPDF网 联系我们和版权申明